BCD AZ78L05ZTR-E1 3-terminal positive linear regulator Datasheet

Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
General Description
Features
The AZ78LXX series are three terminal positive regulators with several fixed output voltages. These regulators can provide local on card regulation, eliminating
the distribution problems associated with single point
regulation. The AZ78LXX can be used in logic systems, instrumentation, HiFi, and other solid state electronic equipment. When used as a Zener diode/resistor
combination replacement, the AZ78LXX usually
results an effective output impedance improvement of
two orders of magnitude, and lower quiescent current.
·
·
·
With adequate heat sinking the AZ78LXX can deliver
100mA output current. Current limiting is included to
limit the peak output current to a safe value. Thermal
protection is also provided. If internal power
dissipation becomes too high for the heat sinking
provided, the thermal shutdown circuit takes over
preventing the IC from overheating.
·
·
·
·
·
·
·
Output Current up to 100mA
Fixed Output Voltages of 5V, 8V, 9V and 12V
Output Voltage Tolerances of ±5% over the Full
Temperature Range
Internal Short Circuit Current-limiting
Internal Thermal Overload Protection
No External Components
Applications
High Efficiency Linear Regulator
Post Regulation for Switching Supply
Microprocessor Power Supply
Mother Board I/O Power Supply
The AZ78LXX are available in the plastic TO-92 (bulk
or ammo packing), SOIC-8, SOT-223 and SOT-89-3
packages.
TO-92
TO-92 Ammo Packing
SOIC-8
SOT-89-3
SOT-223
Figure 1. Package Types of the AZ78LXX
Mar. 2007 Rev. 1. 5
BCD Semiconductor Manufacturing Limited
1
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Pin Configuration
Z Package
(TO-92 Ammo Packing)
Z Package
(TO-92)
3
INPUT
3
INPUT
2
GND
2
GND
1
OUTPUT
1
OUTPUT
H Package
(SOT-223)
4
GND
3
INPUT
2
GND
1
OUTPUT
Connect pin 4 to pin 2 or leave
pin 4 electrically isolated
M Package
(SOIC-8)
R Package
(SOT-89-3)
OUTPUT
1
8
INPUT
GND
2
7
GND
GND
3
6
GND
N/C
4
5
N/C
GND
4
3
INPUT
2
GND
1
OUTPUT
Figure 2. Pin Configuration of the AZ78LXX (Top View)
Mar. 2007 Rev. 1. 5
BCD Semiconductor Manufacturing Limited
2
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Functional Block Diagram
3 (8)
1
INPUT
OUTPUT
A(B)
A for 3-pin
B for 8-pin
2, 4 (2, 3, 6, 7)
GND
Figure 3. Functional Block Diagram of the AZ78LXX
Mar. 2007 Rev. 1. 5
BCD Semiconductor Manufacturing Limited
3
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Ordering Information
-
AZ78L
E1: Lead Free
Blank: Tin Lead
Circuit Type
TR: Tape and Reel or Ammo
Blank: Tube or Bulk
Output Voltage
05: 5V
08: 8V
09: 9V
12: 12V
Package
TO-92
SOIC-8
SOT-89-3
SOT-223
Temperature
Range
-40 to 125oC
-40 to 125oC
-40 to 125oC
-40 to 125oC
Package
Z: TO-92
R: SOT-89-3
H: SOT-223
M: SOIC-8
Part Number
Tin Lead
Marking ID
Lead Free
Tin Lead
Lead Free
Packing Type
AZ78L05Z
AZ78L05Z-E1
AZ78L05Z
AZ78L05Z-E1
Bulk
AZ78L05ZTR
AZ78L05ZTR-E1
AZ78L05Z
AZ78L05Z-E1
Ammo
AZ78L08Z
AZ78L08Z-E1
AZ78L08Z
AZ78L08Z-E1
Bulk
AZ78L08ZTR
AZ78L08ZTR-E1
AZ78L08Z
AZ78L08Z-E1
Ammo
AZ78L09Z
AZ78L09Z-E1
AZ78L09Z
AZ78L09Z-E1
Bulk
AZ78L09ZTR
AZ78L09ZTR-E1
AZ78L09Z
AZ78L09Z-E1
Ammo
AZ78L12Z
AZ78L12Z-E1
AZ78L12Z
AZ78L12Z-E1
Bulk
AZ78L12ZTR
AZ78L12ZTR-E1
AZ78L12Z
AZ78L12Z-E1
Ammo
AZ78L05M
AZ78L05M-E1
78L05M
78L05M-E1
Tube
AZ78L05MTR
AZ78L05MTR-E1
78L05M
78L05M-E1
Tape & Reel
AZ78L08M
AZ78L08M-E1
78L08M
78L08ZM-E1
AZ78L08MTR
AZ78L08MTR-E1
78L08M
78L08M-E1
Tube
Tape & Reel
AZ78L09M
AZ78L09M-E1
78L09M
78L09M-E1
Tube
AZ78L09MTR
AZ78L09MTR-E1
78L09M
78L09M-E1
Tape & Reel
AZ78L12M
AZ78L12M-E1
78L12M
78L12M-E1
Tube
AZ78L12MTR
AZ78L12ZMTR-E1
78L12M
78L12M-E1
Tape & Reel
AZ78L05RTR
AZ78L05RTR-E1
R78A
E78A
Tape & Reel
AZ78L08RTR
AZ78L08RTR-E1
R78B
E78B
Tape & Reel
AZ78L09RTR
AZ78L09RTR-E1
R78C
E78C
Tape & Reel
AZ78L12RTR
AZ78L12RTR-E1
R78D
E78D
Tape & Reel
AZ78L05HTR
AZ78L05HTR-E1
H78A
EH78A
Tape & Reel
AZ78L08HTR
AZ78L08HTR-E1
H78B
EH78B
Tape & Reel
AZ78L09HTR
AZ78L09HTR-E1
H78C
EH78C
Tape & Reel
AZ78L12HTR
AZ78L12HTR-E1
H78D
EH78D
Tape & Reel
BCD Semiconductor's Pb-free products, as designated with "E1" suffix in the part number, are RoHS compliant.
Mar. 2007 Rev. 1. 5
BCD Semiconductor Manufacturing Limited
4
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Absolute Maximum Ratings (Note 1)
Parameter
Input Voltage
Operating Junction Temperature
Lead Temperature (Soldering, 10sec)
Power Dissipation (TA=25oC)
Symbol
Value
Unit
VIN
20
V
TJ
150
o
C
TLEAD
260
o
C
PD
TO-92
0.65
SOIC-8
0.6
SOT-223
0.7
SOT-89-3
0.65
W
Storage Temperature Range
TSTG
-65 to 150
oC
ESD (Human Body Model)
ESD
2000
V
ESD (Machine Model)
ESD
200
V
Note 1: Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to
the device. These are stress ratings only, and functional operation of the device at these or any other conditions
beyond those indicated under "Recommended Operating Conditions" is not implied. Exposure to "Absolute Maximum Ratings" for extended periods may affect device reliability.
Recommended Operating Conditions
Parameter
Symbol
Min
Unit
15
AZ78L05
Input Voltage
Max
AZ78L08
18
VIN
AZ78L09
18
AZ78L12
18
Operating Junction Temperature
TJ
Mar. 2007 Rev. 1. 5
-40
125
V
o
C
BCD Semiconductor Manufacturing Limited
5
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Electrical Characteristics
AZ78L05 Electrical Characteristics
Limits in standard typeface are for TJ=25oC, Bold typeface applies over -40oC to 125oC, IOUT=40mA, CIN
=0.33µF, COUT=0.1µF, VIN=10V, unless otherwise specified.
Parameter
Output Voltage
Symbol
VOUT
Conditions
7.0V ≤ VIN ≤ 15V
Min
Typ
Max
4.8
5
5.2
4.75
Unit
5.25
V
1.0mA ≤ IOUT ≤ 40mA (Note 2)
Line Regulation
VRLINE
7.0V ≤ VIN ≤ 15V
18
75
mV
Load Regulation
VRLOAD
1.0mA ≤ IOUT ≤ 100mA
20
60
mV
Dropout Voltage
VDROP
Quiescent Current
IQ
1.6
IOUT=0
3
Quiescent Current Change
∆IQ
Output Noise Voltage
NO
10Hz ≤ f ≤ 100kHz (Note 3)
PSRR
f=120Hz, 8.0V ≤ VIN ≤ 15V
8.0V ≤ VIN ≤ 15V
1.0mA ≤ IOUT ≤ 40mA
Ripple Rejection
Peak Output Current
5
mA
1.0
mA
0.1
47
IPK
Average Temperature Coefficient of ∆VOUT/ ∆T IOUT = 5.0mA
Output Voltage
Minimum Value of Input Voltage
Required to Maintain Line Regulation
V
VIN (Min)
40
µV
62
dB
150
mA
0.65
mV/ oC
6.7
7
V
Note 2: Power Dissipation ≤ 0.6W
Note 3: Recommended minimum load capacitance of 0.01µF to limit high frequency noise.
Mar. 2007 Rev. 1. 5
BCD Semiconductor Manufacturing Limited
6
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Electrical Characteristics (Continued)
AZ78L08 Electrical Characteristics
Limits in standard typeface are for TJ=25oC, Bold typeface applies over -40oC to 125oC, IOUT=40mA, CIN
=0.33µF, COUT=0.1µF, VIN=14V, unless otherwise specified.
Parameter
Symbol
Conditions
Min
Typ
Max
7.7
8.0
8.3
Unit
Output Voltage
VOUT
Line Regulation
VRLINE
11V ≤ VIN ≤ 18V
18
75
mV
Load Regulation
VRLOAD
1.0mA ≤ IOUT ≤ 100mA
20
90
mV
Dropout Voltage
VDROP
11V ≤ VIN ≤ 18V
7.6
8.4
V
1.0mA ≤ IOUT ≤ 40mA (Note 2)
Quiescent Current
Quiescent Current Change
Output Noise Voltage
Ripple Rejection
Peak Output Current
IQ
∆IQ
1.6
IOUT=0
3
5
mA
11V ≤ VIN ≤ 18V
1.5
mA
1.0mA ≤ IOUT ≤ 40mA
0.1
NO
10Hz ≤ f ≤ 100kHz (Note 3)
PSRR
f=120Hz, 11V ≤ VIN ≤ 18V
39
IPK
Average Temperature Coefficient of ∆VOUT/ ∆T IOUT= 5.0mA
Output Voltage
Minimum Value of Input Voltage
Required to Maintain Line Regulation
V
VIN (Min)
60
µV
45
dB
150
mA
0.8
mV/ oC
9.7
V
Note 2: Power Dissipation ≤ 0.6W
Note 3: Recommended minimum load capacitance of 0.01µF to limit high frequency noise.
Mar. 2007 Rev. 1. 5
BCD Semiconductor Manufacturing Limited
7
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Electrical Characteristics (Continued)
AZ78L09 Electrical Characteristics
Limits in standard typeface are for TJ=25oC, Bold typeface applies over -40oC to 125oC, IOUT=40mA, CIN
=0.33µF, COUT=0.1µF, VIN =15V, unless otherwise specified.
Parameter
Output Voltage
Symbol
VOUT
Conditions
12V ≤ VIN ≤ 18V
Min
Typ
Max
8.6
9
9.4
Unit
9.45
V
18
75
mV
20
90
mV
8.55
1.0mA ≤ IOUT ≤ 40mA (Note 2)
Line Regulation
VRLINE
12V ≤ VIN ≤ 18V
Load Regulation
VRLOAD
1.0mA ≤ IOUT ≤ 100mA
Dropout Voltage
VDROP
Quiescent Current
Quiescent Current Change
Output Noise Voltage
Ripple Rejection
Peak Output Current
IQ
∆IQ
1.6
IOUT=0
3
5
mA
12V ≤ VIN ≤ 18V
1.5
mA
1.0mA ≤ IOUT ≤ 40mA
0.1
NO
10Hz ≤ f ≤ 100kHz (Note 3)
PSRR
f=120Hz, 12V ≤ VIN ≤ 18V
IPK
70
38
VIN (Min)
µV
44
dB
150
mA
0.9
mV/ oC
10.7
V
Average Temperature Coefficient of ∆VOUT/ ∆T IOUT= 5.0mA
Output Voltage
Minimum Value of Input Voltage
Required to Maintain Line Regulation
V
Note 2: Power Dissipation ≤ 0.6W
Note 3: Recommended minimum load capacitance of 0.01µF to limit high frequency noise.
Mar. 2007 Rev. 1. 5
BCD Semiconductor Manufacturing Limited
8
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Electrical Characteristics (Continued)
AZ78L12 Electrical Characteristics
Limits in standard typeface are for TJ=25oC, Bold typeface applies over -40oC to 125oC, IOUT=40mA, CIN
=0.33µF, COUT=0.1µF, VIN=18V, unless otherwise specified.
Parameter
Output Voltage
Symbol
VOUT
Conditions
15V ≤ VIN ≤ 18V
Min
Typ
Max
11.5
12
12.5
11.4
Unit
12.6
V
1.0mA ≤ IOUT ≤ 40mA (Note 2)
Line Regulation
VRLINE
15V ≤ VIN ≤ 18V
18
75
mV
Load Regulation
VRLOAD
1.0mA ≤ IOUT ≤ 100mA
20
90
mV
Dropout Voltage
VDROP
Quiescent Current
IQ
1.6
IOUT=0
3
Quiescent Current Change
∆IQ
Output Noise Voltage
NO
10Hz ≤ f ≤ 100kHz (Note 3)
PSRR
f=120Hz, 15V ≤ VIN ≤ 18V
15V ≤ VIN ≤ 18V
1.0mA ≤ IOUT ≤ 40mA
Ripple Rejection
Peak Output Current
IPK
VIN (Min)
5
mA
1.5
mA
0.1
80
µV
54
dB
150
mA
1.0
mV/ oC
13.7
V
40
Average Temperature Coefficient of ∆VOUT/ ∆T IOUT = 5.0mA
Output Voltage
Minimum Value of Input Voltage
Required to Maintain Line Regulation
V
Note 2: Power Dissipation ≤ 0.6W
Note 3: Recommended minimum load capacitance of 0.01µF to limit high frequency noise.
Mar. 2007 Rev. 1. 5
BCD Semiconductor Manufacturing Limited
9
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Typical Performance Characteristics
2.0
5
1.6
IOUT=40mA
3
IOUT=1mA
2
1.4
1.2
IOUT=1mA
1.0
0.8
0.6
1
AZ78L05
∆V=1%*VOUT
0.4
0.2
0
0
2
4
6
8
0.0
-40
10
-20
0
VI input
voltage(V)
(V)
Input Voltage
20
40
60
80
100
120
o
Junction Temperature ( C)
Figure 4. Dropout Characteristics
Figure 5. Dropout Voltage vs. Junction Temperature
3.0
3.0
2.9
AZ78L05
VIN=10V
2.8
IOUT=5mA
2.5
Input Bias Current (mA)
Quiescent Current (mA)
IOUT=100mA
IOUT=100mA
TJ =25 oC
Dropout Voltage (V)
4
Output Voltage (V)
IOUT=40mA
1.8
AZ78L05
VOUT=5V
2.7
2.6
2.5
2.0
1.5
AZ78L05
VOUT=5.0V
1.0
IOUT=40mA
o
2.4
TJ=25 C
0.5
2.3
2.2
-40
0.0
-20
0
20
40
60
80
100
0
120
2
4
6
8
10
12
14
16
18
20
Input Voltage (V)
o
Junction Temperature ( C)
Figure 6. Quiescent Current vs. Junction Temperature
Figure 7. Input Bias Current vs. Input Voltage
Mar. 2007 Rev. 1. 5
BCD Semiconductor Manufacturing Limited
10
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Typical Performance Characteristics (Continued)
1
VIN (0.5V/Div)
11.5
∆VOUT (20mV/Div)
Power Dissipation (W)
No Heatsink
o
θJA=250 C/W
0.1
o
PD(MAX) at 25 C=0.6W
Package: SOIC-8
AZ78L05
11
10.5
10
20
0
-20
-40
0
25
50
75
100
125
150
Time (4µs/Div)
o
Ambient Temperature ( C)
Figure 8. Power Dissipation vs. Ambient Temperature
Figure 9. Line Transient Response
(Conditions: VIN=10 to 11V, VOUT=5V, IOUT=40mA)
∆VOUT (100mV/Div)
IOUT (25mA/Div)
75
AZ78L05
50
25
0
0
-100
-200
-300
Time (10µs/Div)
Figure 10. Load Transient Response
(Conditions: VIN=10V, VOUT=5V, IOUT=1 to 50mA)
Mar. 2007 Rev. 1. 5
BCD Semiconductor Manufacturing Limited
11
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Typical Application
VIN
3
AZ78L05
VOUT
1
+
+
2
0.33µF
(Note 4)
0.1µF
(Note 4)
Note 4: Bypass capacitors are recommended for optimum stability and transient response and should be located
as close as possible to the regulator.
Figure 11. Typical Application of the AZ78LXX
Mar. 2007 Rev. 1. 5
BCD Semiconductor Manufacturing Limited
12
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Mechanical Dimensions
TO-92
Unit: mm(inch)
1.100(0.043)
3.430(0.135)
MIN
3.700(0.146)
3.300(0.130)
1.400(0.055)
0.360(0.014)
0.510(0.020)
0.000(0.000)
0.380(0.015)
Φ1.600(0.063)
MAX
4.700(0.185)
0.380(0.015)
0.550(0.022)
14.100(0.555)
14.500(0.571)
4.300(0.169)
4.400(0.173)
4.700(0.185)
1.270(0.050)
TYP
2.440(0.096)
2.640(0.104)
Mar. 2007 Rev. 1. 5
BCD Semiconductor Manufacturing Limited
13
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Mechanical Dimensions (Continued)
TO-92 Ammo Packing
12.400(0.488)
13.000(0.512)
Unit: mm(inch)
±1.000(0.039)
±1.000(0.039)
4.400(0.173)
4.600(0.181)
ΔP
Δh
3.400(0.134)
3.600(0.142)
4.400(0.173)
4.600(0.181)
19.000(0.748)
21.000(0.827)
0.380(0.015)
0.550(0.022)
2.200(0.087)
2.800(0.110)
1.000 (0.039) MAX
15.500(0.610)
16.500(0.650)
5.500(0.217)
6.500(0.256)
2.500(0.098)
MIN
3.800(0.150)
4.200(0.165)
17.500(0.689)
19.000(0.748)
2.200(0.087)
2.800(0.110)
6.050(0.238)
6.650(0.262)
8.500(0.335)
9.500(0.374)
3.550(0.140)
4.150(0.163)
12.500(0.492)
12.900(0.508)
0.150(0.006)
0.250(0.010)
0.350(0.014)
0.450(0.018)
Mar. 2007 Rev. 1. 5
BCD Semiconductor Manufacturing Limited
14
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Mechanical Dimensions (Continued)
SOIC-8
4.700(0.185)
5.100(0.201)
7°
Unit: mm(inch)
0.320(0.013)
1.350(0.053)
1.750(0.069)
8°
8°
7°
0.675(0.027)
0.725(0.029)
D
5.800(0.228)
1.270(0.050)
6.200(0.244)
TYP
D
20:1
φ 0.800(0.031)
0.300(0.012)
R0.150(0.006)
0.100(0.004)
0.200(0.008)
0°
8°
1.000(0.039)
3.800(0.150)
4.000(0.157)
0.330(0.013)
0.190(0.007)
0.250(0.010)
1°
5°
0.510(0.020)
0.900(0.035)
R0.150(0.006)
0.450(0.017)
0.800(0.031)
Mar. 2007 Rev. 1. 5
BCD Semiconductor Manufacturing Limited
15
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Mechanical Dimensions (Continued):
SOT-223
Unit: mm(inch)
6.300(0.248)
6.700(0.264)
)
0.250(0.010
)
4
1
0.350(0.0
2.900(0.114)
3.100(0.122)
0.900(0.035)
3.700(0.146)
3.300(0.130)
7.300(0.287)
6.700(0.264)
MIN
0.250(0.010)
1.750(0.069)
TYP
2.300(0.091)
0.610(0.024)
TYP
0.810(0.032)
4.500(0.177)
0°
10°
4.700(0.185)
0.020(0.001)
0.100(0.004)
1.500(0.059)
1.520(0.060)
1.700(0.067)
1.800(0.071)
Mar. 2007 Rev. 1. 5
BCD Semiconductor Manufacturing Limited
16
Data Sheet
3-TERMINAL POSITIVE LINEAR REGULATOR
AZ78LXX
Mechanical Dimensions (Continued):
SOT-89-3
Unit: mm(inch)
4.400(0.173)
4.600(0.181)
1.630(0.064)
1.400(0.055)
1.600(0.063)
1.830(0.072)
0.000(0.000)
0.076(0.003)
1.400(0.055)*
1.200(0.047)
0.900(0.035)
3.950(0.156)
4.250(0.167)
R0.200(0.008)
2.300(0.091)
2.600(0.102)
3°
10°
0.360(0.014)
0.360(0.014)
0.360(0.014)
0.520(0.020)
0.480(0.019)
0.440(0.017)
0.440(0.017)
3.000(0.118)
0.560(0.022)
3°
10°
R0.150(0.006)
Mar. 2007 Rev. 1. 5
BCD Semiconductor Manufacturing Limited
17
http://www.bcdsemi.com
IMPORTANT NOTICE
BCD Semiconductor Manufacturing Limited reserves the right to make changes without further notice to any products or specifications herein. BCD Semiconductor Manufacturing Limited does not assume any responsibility for use of any its products for any
particular purpose, nor does BCD Semiconductor Manufacturing Limited assume any liability arising out of the application or use
of any its products or circuits. BCD Semiconductor Manufacturing Limited does not convey any license under its patent rights or
other rights nor the rights of others.
MAIN SITE
BCD Semiconductor Manufacturing Limited
BCD Semiconductor Manufacturing Limited
- Wafer Fab
Shanghai SIM-BCD Semiconductor Manufacturing Limited
800, Yi Shan Road, Shanghai 200233, China
Tel: +86-21-6485 1491, Fax: +86-21-5450 0008
- IC Design Group
Advanced Analog Circuits (Shanghai) Corporation
8F, Zone B, 900, Yi Shan Road, Shanghai 200233, China
Tel: +86-21-6495 9539, Fax: +86-21-6485 9673
REGIONAL SALES OFFICE
Shenzhen Office
Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd. Shenzhen Office
Advanced Analog Circuits (Shanghai) Corporation Shenzhen Office
Room E, 5F, Noble Center, No.1006, 3rd Fuzhong Road, Futian District, Shenzhen 518026, China
Tel: +86-755-8826 7951
Fax: +86-755-8826 7865
Taiwan Office
BCD Semiconductor (Taiwan) Company Limited
4F, 298-1, Rui Guang Road, Nei-Hu District, Taipei,
Taiwan
Tel: +886-2-2656 2808
Fax: +886-2-2656 2806
USA Office
BCD Semiconductor Corporation
30920 Huntwood Ave. Hayward,
CA 94544, U.S.A
Tel : +1-510-324-2988
Fax: +1-510-324-2788
Similar pages