AD ADA4320-1ACPZ-RL High power, low distortion upstream Datasheet

High Power, Low Distortion Upstream
CATV Line Driver
ADA4320-1
FUNCTIONAL BLOCK DIAGRAM
Supports CableLabs® DOCSIS 3.0/2.0 and EuroDOCSIS
3.0/2.0 specifications for customer premises equipment
(CPE) upstream transmission
5 V single-supply operation
Excellent adjacent channel rejection performance
−66 dBc ACPR for a single QPSK channel
−63 dBc ACPR for 4× QAM64 channels
Gain programmable in 1 dB steps over a 59 dB range
Gain range: −27 dB to +32 dB
Current-scaled output stage
Low between-burst output noise level
−70 dB mV in 160 kHz bandwidth
Maintains constant output impedance in enable, disable,
and sleep conditions
Selectable low power modes
12 mA in Tx disable
12 μA in sleep mode (full power-down)
3-wire, SPI-compatible interface
4 mm × 5 mm 24-lead LFCSP, RoHS compliant
VIN–
VIN+
VOUT+
DIFF OR
SINGLE
INPUT
AMP
ATTENUATION
CORE
VERNIER
VOUT–
8
ZIN (SINGLE) = 320Ω
ZIN (DIFF) = 640Ω
DECODE
8
DATA LATCH
ZOUT DIFF =
300Ω
POWER-DOWN
LOGIC
RAMP
8
ADA4320-1
GND
POWER
AMP
SHIFT
REGISTER
DATEN SDATA CLK
TXEN
SLEEP
08707-001
FEATURES
Figure 1.
APPLICATIONS
DOCSIS 3.0 and EuroDOCSIS cable modems/E-MTAs
DOCSIS 3.0 set-top boxes
CATV telephony modems
Coaxial or twisted pair line drivers
GENERAL DESCRIPTION
The ADA4320-1 is a high power, ultralow distortion amplifier
designed for CATV reverse channel line driving. Its features and
specifications make the ADA4320-1 ideally suited for DOCSIS 3.0and EuroDOCSIS 3.0-based applications. Both gain and output
stage current are controlled via a 3-wire (SPI-compatible) interface.
A single 8-bit serial word selects one of four available supply
current presets and one of sixty gain codes.
The ADA4320-1 has been tailored to address both the high output
drive and stringent fidelity requirements of DOCSIS 3.0. The
part is able to maintain excellent adjacent channel rejection
performance over the full 5 MHz to 85 MHz range, even with
multiple bonded channels at maximum specified output levels.
The ADA4320-1 accepts a differential or single-ended input
signal. The output is specified for driving a single-ended 75 Ω
load through a 4:1 impedance transformer.
The ADA4320-1 features an output driver stage that scales
quiescent current consumption according to gain setting. In
multichannel mode at maximum gain (32 dB), the device draws
260 mA from a single 5 V supply, enabling the high power,
ultralow distortion performance required by multiple DOCSIS 3.0
upstream channels. For lifeline E-MTA applications, the ADA4320-1
output stage current can be throttled via SPI commands, reducing
the power requirement for single-channel transmission by up to
30%. In transmit-disable mode, the ADA4320-1 draws only 12 mA.
The device also features a full power-down sleep mode that
further reduces current draw to12 μA typical.
The ADA4320-1 is packaged in a RoHS-compliant, 24-lead
exposed pad LFCSP and is rated for operation over the −40°C
to +85°C temperature range.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
© 2010 Analog Devices, Inc. All rights reserved.
ADA4320-1
TABLE OF CONTENTS
Features .............................................................................................. 1
General Applications ................................................................. 11
Applications ....................................................................................... 1
Circuit Description .................................................................... 11
Functional Block Diagram .............................................................. 1
Programming .............................................................................. 11
General Description ......................................................................... 1
Current Level and Gain Adjustment ....................................... 11
Revision History ............................................................................... 2
Power Saving Features ............................................................... 12
Specifications..................................................................................... 3
Input Bias, Impedance, and Termination................................ 12
Logic Inputs (TTL-/CMOS-Compatible Logic) ....................... 4
Output Bias, Impedance, and Termination ............................ 12
Timing Requirements .................................................................. 5
Power Supply............................................................................... 12
Absolute Maximum Ratings............................................................ 6
Signal Integrity Layout Considerations ................................... 12
Thermal Resistance ...................................................................... 6
Initial Power-Up ......................................................................... 12
Maximum Power Dissipation ..................................................... 6
RAMP Pin Feature...................................................................... 13
ESD Caution .................................................................................. 6
Output Transformer ................................................................... 13
Pin Configuration and Function Descriptions ............................. 7
Outline Dimensions ....................................................................... 14
Typical Performance Characteristics ............................................. 8
Ordering Guide .......................................................................... 14
Applications Information .............................................................. 11
REVISION HISTORY
4/10—Revision 0: Initial Version
Rev. 0 | Page 2 of 16
ADA4320-1
SPECIFICATIONS
TA = 25°C, VS = 5 V, RL = 75 Ω, VIN (differential) = 29 dB mV sinusoidal, f = 5 MHz to 85 MHz, gain, VOUT (single-ended) measured at
output of Coilcraft PWB-4-BL transformer, unless otherwise noted.
Table 1.
Parameter
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
GAIN CONTROL
Gain Range
Maximum Gain
Minimum Gain
Output Step Size
OUTPUT CHARACTERISTICS
Gain Flatness
At Maximum Gain
At Minimum Gain
1 dB Compression Point (P1dB)
Output Noise in 160 kHz Bandwidth
At Maximum Gain
At Minimum Gain
Transmit Disabled
Output Impedance (Measured at
Transformer Output)
Output Return Loss (Measured at
Transformer Output)
OVERALL PERFORMANCE
Adjacent Channel Power Ratio (ACPR)
Single QPSK Channel
4x QAM64 Channels
Output Third-Order Intercept Point (OIP3)
Input-to-Output Isolation
Conditions
Min
Balanced (differential) input
Unbalanced (single-ended) input
Typ
Max
640
320
2.0
Unit
Ω
Ω
pF
Current Level 3
57.5
30.5
Gain Code 60
Gain Code 01
0.6
Referenced to 10 MHz
f = 42 MHz, Gain Code 60, Current Level 3
f = 65 MHz, Gain Code 60, Current Level 3
f = 85 MHz, Gain Code 60, Current Level 3
f = 42 MHz, Gain Code 01, Current Level 0
f = 65 MHz, Gain Code 01, Current Level 0
f = 85 MHz, Gain Code 01, Current Level 0
f = 10 MHz, Gain Code 60, Current Level 3, output referred
f = 10 MHz, 294 Ω resistor across VIN+ and VIN− pins
Gain Code 60, Current Level 3, TXEN = high (1)
Gain Code 60, Current Level 0, TXEN = high (1)
Gain Code 01, Current Level 3, TXEN = high (1)
Gain Code 01, Current Level 0, TXEN = high (1)
TXEN = low (0)
TXEN = high (1) or TXEN = low (0) or SLEEP = low (0)
59
32
−27
1.0
60
−25.5
1.4
dB
dB
dB
dB/LSB
−0.3
−0.7
−1.1
−0.4
−0.8
−1.8
70
dB
dB
dB
dB
dB
dB
dB mV
−20
−21
−60
−61
−70
75
dB mV
dB mV
dB mV
dB mV
dB mV
Ω
SLEEP = high (1), TXEN = high (1)
SLEEP = high (1), TXEN = low (0)
SLEEP = low (0)
12
11
10
dB
dB
dB
f = 5 MHz to 85 MHz, output level = 61 dB mV,
Gain Code 60, Current Level 3, channel width = 6.4 MHz,
adjacent channel width = 6.4 MHz
f = 5 MHz to 85 MHz, output level = 53 dB mV/channel,
Gain Code 60, Current Level 3, channel width = 1.6 MHz,
adjacent channel width = 1.6 MHz
f1 = 84 MHz, f2 = 85 MHz, Gain Code 60, Current Level 3
f1 = 84 MHz, f2 = 85 MHz, Gain Code 60, Current Level 0
f = 85 MHz, Gain Code 60, TXEN = Low (0)
−66
dBc
−63
dBc
93
87
107
dB mV
dB mV
dB
−19
−20
−59
−60
−68
f = 85 MHz
Rev. 0 | Page 3 of 16
ADA4320-1
Parameter
POWER CONTROL
Transmit Enable Settling Time
Transmit Disable Settling Time
Output Switching Transients
POWER SUPPLY
Operating Range
Quiescent Current
At Maximum Gain
At Minimum Gain
Conditions
Min
TXEN = 0 to 1, Gain Code 60, no input signal
TXEN = 1 to 0, Gain Code 60, no input signal
Gain Code 60
Gain Code 01
Typ
Max
5.5
7
20
2
4.75
Gain Code 60, Current Level 3
Gain Code 60, Current Level 2
Gain Code 60, Current Level 1
Gain Code 60, Current Level 0
Gain Code 01, Current Level 3
Gain Code 01, Current Level 2
Gain Code 01, Current Level 1
Gain Code 01, Current Level 0
TXEN = 0, all gain codes, all current levels
SLEEP = 0 (power-down)
OPERATING TEMPERATURE RANGE
−40
Unit
μs
μs
mV p-p
mV p-p
5.00
5.25
V
260
235
210
180
77
73
70
65
12
12
300
270
250
210
100
95
90
80
15
80
mA
mA
mA
mA
mA
mA
mA
mA
mA
μA
+85
°C
LOGIC INPUTS (TTL-/CMOS-COMPATIBLE LOGIC)
DATEN, CLK, SDATA, TXEN, SLEEP, VS = 5 V; full temperature range.
Table 2.
Parameter
Logic 1 Voltage
Logic 0 Voltage
Digital Input Leakage Current (Both Logic Levels, All Digital Pins)
Rev. 0 | Page 4 of 16
Min
2.0
0
−5
Typ
Max
VS
0.8
+5
Unit
V
V
μA
ADA4320-1
TIMING REQUIREMENTS
Full temperature range, VCC = 5 V, tR = tF = 4 ns, fCLK = 8 MHz, unless otherwise noted.
Table 3.
Parameter
Clock Pulse Width (tWH)
Clock Period (tC)
Setup Time SDATA vs. Clock (tDS)
Setup Time DATEN vs. Clock (tES)
Hold Time SDATA vs. Clock (tDH)
Hold Time DATEN vs. Clock (tEH)
Input 10% to 90% Rise and Fall Times, SDATA, DATEN, Clock
Min
16
32
5
16
5
3
Typ
10
tDS
SDATA
VALID DATA-WORD G1
MSB...LSB
tWH
VALID DATA-WORD G2
tC
CLK
tES
tEH
8 CLOCK CYCLES
DATEN
Max
GAIN TRANSFER (G1)
GAIN TRANSFER (G2)
TXEN
08707-002
ANALOG
OUTPUT
SIGNAL AMPLITUDE (p-p)
Figure 2. Serial Interface Timing
VALID DATA BIT
SDATA MSB
MSB – 1
tDH
08707-003
tDS
MSB – 2
CLK
Figure 3. SDATA Timing
Rev. 0 | Page 5 of 16
Unit
ns
ns
ns
ns
ns
ns
ns
ADA4320-1
ABSOLUTE MAXIMUM RATINGS
MAXIMUM POWER DISSIPATION
Table 4.
Parameter
Supply Voltage
Maximum Power Dissipation
Storage Temperature Range
Operating Temperature Range
Lead Temperature (Soldering, 10 sec)
Junction Temperature
Rating
5.5 V
1.65 W
−65°C to +125°C
−40°C to +85°C
300°C
150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL RESISTANCE
θJA is specified for the device soldered to a high thermal
conductivity 4-layer (2s2p) circuit board, as described in
EIA/JESD 51-7.
The maximum safe power dissipation in the ADA4320-1 package
is limited by the associated rise in junction temperature (TJ) on
the die. At approximately 150°C, which is the glass transition
temperature, the plastic changes its properties. Even temporarily
exceeding this temperature limit can change the stresses that
the package exerts on the die, permanently shifting the parametric
performance of the ADA4320-1. Exceeding a junction temperature
of 150°C for an extended time can result in changes in the silicon
devices, potentially causing failure.
Airflow increases heat dissipation, effectively reducing θJA. In
addition, more metal directly in contact with the package leads
from metal traces, through-holes, ground, and power planes,
reduces the θJA. The exposed paddle on the underside of the
package must be soldered to a pad on the PCB surface that is
thermally connected to a copper plane to achieve the specified θJA.
ESD CAUTION
Table 5. Thermal Resistance
Package Type
24-lead LFCSP
θJA
31.2
θJC
5.7
Unit
°C/W
Rev. 0 | Page 6 of 16
ADA4320-1
24
23
22
21
20
COMP
VOUT+
VOUT–
VOUT+
VOUT–
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
ADA4320-1
TOP VIEW
(Not to Scale
19
18
17
16
15
14
13
GND
GND
GND
SLEEP
CLK
SDATA
DATEN
NOTES
1. EXPOSED THERMAL PAD MUST BE ELECTRICALLY AND
THERMALLY CONNECTED TO PCB GROUND (GND) PLANE.
08707-005
GND
GND
VIN–
VIN+
GND
8
9
10
11
12
GND
GND
VCC
VCC
VCC
RAMP
TXEN
Figure 4. Pin Configuration, Top View
Table 6. Pin Function Descriptions
Pin No.
1, 2, 8, 9, 12,
17, 18, 19,
EPAD
3, 4, 5
6
7
10
11
13
Mnemonic
GND
Description
Common External Ground Reference.
VCC
RAMP
TXEN
VIN−
VIN+
DATEN
14
SDATA
15
CLK
16
SLEEP
20, 22
21, 23
24
VOUT−
VOUT+
COMP
Common Positive External Supply Voltage.
External RAMP Capacitor (Optional).
Transmit Enable. Logic 0 disables forward transmission, and Logic 1 enables forward transmission.
Inverting Input. DC-biased to approximately VCC/2. This pin should be ac-coupled with a 0.1 μF capacitor.
Noninverting Input. DC-biased to approximately VCC/2. This pin should be ac-coupled with a 0.1 μF capacitor.
Data Enable Low Input. This port controls the 8-bit parallel data latch and shift register. A Logic 0-to-1 transition
transfers the latched data to the attenuator core (updates the gain) and simultaneously inhibits serial data transfer
into the register. A 1-to-0 transition inhibits the data latch (holds the previous, and simultaneously enables the
register for serial data load).
Serial Data Input. This digital input allows an 8-bit serial control word to be loaded into the internal register with the
most significant bit (MSB) first.
Clock Input. The clock port controls the serial attenuator data transfer rate to the 8-bit master-slave shift register. A
Logic 0-to-1 transition latches the data bit, and a Logic 1-to-0 transition transfers the data bit to the slave. This
requires the input serial data-word to be valid at or before this clock transition.
Low Power Sleep Mode. In sleep mode, the supply current is reduced to 12 μA typical. Logic 0 powers down
the device, and Logic 1 powers up the device.
Negative Output Signal. This pin must be biased to VCC.
Positive Output Signal. This pin must be biased to VCC.
Internal Compensation. This pin must be externally decoupled (0.1 μF capacitor).
Rev. 0 | Page 7 of 16
ADA4320-1
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, VS = 5 V, RL = 75 Ω, VIN (differential) = 29 dBmV sinusoidal, f = 5 MHz to 85 MHz, Gain Code 60 (maximum), Current Level 3
(maximum), VOUT (single-ended) measured at output of Coilcraft PWB-4-BL transformer, unless otherwise noted.
300
CURRENT
CURRENT
CURRENT
CURRENT
3
2
1
0
60
VIN = 29dBmV
CURRENT LEVEL 3
VIN = 29dBmV
45
GAIN CODE 60
30
GAIN CODE 40
15
200
GAIN (dB)
SUPPLY CURRENT (mA)
250
LEVEL
LEVEL
LEVEL
LEVEL
150
0
GAIN CODE 20
–15
GAIN CODE 01
–30
100
0
6
12
18
24
30
36
42
48
54
60
GAIN CODE
–60
1M
08707-006
50
10M
Figure 5. Supply Current vs. Gain Code
270
Figure 8. Gain vs. Frequency
1.0
GAIN CODE 60
CURRENT LEVEL 3
0.5
NORMALIZED GAIN (dB)
SUPPLY CURRENT (mA)
5.00V
265
4.75V
255
250
245
LEVEL
LEVEL
LEVEL
LEVEL
3
2
1
0
GAIN CODE 60 (MAXIMUM)
VIN = 29dBmV
0
–0.5
–1.0
–1.5
240
–40
–20
0
20
40
60
80
100
AMBIENT TEMPERATURE (°C)
–2.0
08707-007
235
–60
5
10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85
FREQUENCY (MHz)
Figure 9. Normalized Frequency Response at Maximum Gain
Figure 6. Supply Current vs. Ambient Temperature at Maximum Gain
75
CURRENT
CURRENT
CURRENT
CURRENT
5.25V
260
1G
08707-010
275
100M
FREQUENCY (Hz)
08707-009
–45
1.0
GAIN CODE 01
CURRENT LEVEL 0
+85°C
+25°C
–40°C
0.5
GAIN CODE 60 (MAXIMUM)
VIN = 29dBmV
NORMALIZED GAIN (dB)
SUPPLY CURRENT (mA)
70
5.25V
65
5.00V
60
4.75V
0
–0.5
–1.0
–1.5
–2.0
55
–40
–20
0
20
40
60
AMBIENT TEMPERATURE (°C)
80
100
–3.0
5
10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85
FREQUENCY (MHz)
Figure 10. Normalized Frequency Response over Temperature
Figure 7. Supply Current vs. Ambient Temperature at Minimum Gain
Rev. 0 | Page 8 of 16
08707-011
50
–60
08707-008
–2.5
ADA4320-1
80
–30
–40
–50
–60
–70
–80
24
30
36
42
48
54
60
GAIN CODE
40
30
20
0
ADJACENT CHANNEL POWER RATIO (dBc)
OUTPUT RETURN LOSS (dB)
–40
–10
–15
–20
–30
10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85
FREQUENCY (MHz)
–45
–50
–65
–66
–67
–68
25
35
45
55
65
60
54
75
FREQUENCY (MHz)
80
70
60
ACPR
40
–65
30
–70
20
OUTPUT
LEVEL
–75
10
6
12
18
24
30
36
42
48
54
0
60
GAIN CODE
–52
CURRENT LEVEL 0
CURRENT LEVEL 1
CURRENT LEVEL 2
CURRENT LEVEL 3
–64
15
48
Figure 15. ACPR and Output Level vs. Gain Code
–63
5
42
50
–60
ADJACENT CHANNEL POWER RATIO (dBc)
–62
36
–55
0
85
08707-015
ADJACENT CHANNEL POWER RATIO (dBc)
SINGLE QPSK CHANNEL
OUTPUT LEVEL = 61dBmV
GAIN CODE 60 (MAXIMUM)
CHANNEL WIDTH = 6.4MHz
ADJACENT CHANNEL WIDTH = 6.4MHz
30
SINGLE QPSK CHANNEL
INPUT LEVEL = 29dBmV
CURRENT LEVEL 3
CHANNEL WIDTH = 6.4MHz
DRIVEN CHANNEL CENTER = 42MHz
ADJACENT CHANNEL WIDTH = 6.4MHz
ADJACENT CHANNEL CENTER = 48.4MHz
Figure 12. Output Return Loss (S22) vs. Frequency
–61
24
–80
08707-012
–25
5
18
Figure 14. Output 1 dB Compression Point vs. Gain Code
SLEEP
TX DISABLE
TX ENABLE
–5
12
GAIN CODE
Figure 11. Noise Power vs. Gain Code
0
6
OUTPUT LEVEL (dBmV)
18
50
08707-017
12
60
4× QAM64 CHANNELS (UNCORRELATED)
OUTPUT LEVEL = 53dBmV/CHANNEL
GAIN CODE 60 (MAXIMUM)
CHANNEL WIDTH = 1.6MHz
ADJACENT CHANNEL WIDTH = 1.6MHz
–54
–56
CURRENT
CURRENT
CURRENT
CURRENT
–58
LEVEL
LEVEL
LEVEL
LEVEL
0
1
2
3
–60
–62
–64
–66
5
15
25
35
45
55
65
75
FREQUENCY (MHz)
Figure 16. ACPR vs. Frequency for 4× QAM64 Channels
Figure 13. ACPR vs. Frequency for Single QPSK Channel
Rev. 0 | Page 9 of 16
85
08707-016
6
70
08707-014
–20
0
CURRENT LEVEL 3
CURRENT LEVEL 0
OUTPUT 1dB COMPRESSION POINT (dBmV)
TXEN = 1, ALL CURRENT LEVELS
TXEN = 0
08707-013
NOISE POWER IN 160kHz BANDWIDTH (dBmV)
–10
ADA4320-1
–22
CURRENT LEVEL 0
CURRENT LEVEL 1
CURRENT LEVEL 2
CURRENT LEVEL 3
–48
–52
–56
–60
–64
–68
–72
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42
INPUT LEVEL (dBmV)
–46
–52
–58
–64
–70
12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
INPUT LEVEL (dBmV/CHANNEL)
Figure 17. ACPR vs. Input Level for a Single QPSK Channel
–30
–40
ADJACENT CHANNEL POWER RATIO (dBc)
–20
–10
SINGLE QPSK CHANNEL
GAIN CODE 60 (MAXIMUM)
CHANNEL WIDTH = 6.4MHz
DRIVEN CHANNEL CENTER = 42MHz
ADJACENT CHANNEL WIDTH = 6.4MHz
ADJACENT CHANNEL CENTER = 48.4MHz
CURRENT LEVEL 0
CURRENT LEVEL 1
CURRENT LEVEL 2
CURRENT LEVEL 3
–50
–60
–70
–80
59
60
61
62
63
64
65
66
67
68
69
70
71
OUTPUT LEVEL (dBmV)
OUTPUT GLITCH AMPLITUDE (mV p-p)
0
–2
–4
PEAK OUTPUT
ENVELOPE
–8
–2
0
2
4
6
8
10
12
14
TIME (µs)
16
18
08707-022
OUTPUT AMPLITUDE (V)
2
–6
CURRENT LEVEL 0
CURRENT LEVEL 1
CURRENT LEVEL 2
CURRENT LEVEL 3
–40
–50
–60
–70
120
TXEN
4
–30
46
48
50
52
54
56
58
60
62
Figure 21. ACPR vs. Output Level for 4x QAM64 Channels
4× QAM64 CHANNELS (UNCORRELATED)
OUTPUT LEVEL = 53dBmV/CHANNEL
CHANNEL WIDTH = 1.6MHz
CHANNEL CENTERS = 39.6MHz, 41.2MHz, 42.8MHz, 44.4MHz)
6
–20
OUTPUT LEVEL (dBmV/CHANNEL)
Figure 18. ACPR vs. Output Level for a Single QPSK Channel
8
4× QAM64 CHANNELS (UNCORRELATED)
GAIN CODE 60 (MAXIMUM)
CHANNEL WIDTH = 1.6MHz
DRIVEN CHANNEL CENTER = 77.8MHz, 79.4MHz,
81.0MHz, 82.6MHz
ADJACENT CHANNEL WIDTH = 1.6MHz
ADJACENT CHANNEL CENTER = 84.2MHz
–80
44
08707-020
ADJACENT CHANNEL POWER RATIO (dBc)
–10
Figure 20. ACPR vs. Input Level for 4× QAM64 Channels
08707-021
–44
81.0MHz, 82.6MHz
ADJACENT CHANNEL WIDTH = 1.6MHz
–34 ADJACENT CHANNEL CENTER = 84.2MHz
CURRENT LEVEL 0
CURRENT LEVEL 1
–40
CURRENT LEVEL 2
CURRENT LEVEL 3
Figure 19. Transmit Enable/Disable Response
TXEN = 1
TXEN = 0
DOCSIS 3.0 LIMIT (FOR 29dBmV INPUT)
100
80
60
40
20
0
0
6
12
18
24
30
36
42
48
54
GAIN CODE
Figure 22. Output Glitch Amplitude vs. Gain Code
Rev. 0 | Page 10 of 16
60
08707-023
–40
4× QAM64 CHANNELS (UNCORRELATED)
GAIN CODE 42 (14dB)
CHANNEL WIDTH = 1.6MHz
–28 DRIVEN CHANNEL CENTER = 77.8MHz, 79.4MHz,
08707-019
ADJACENT CHANNEL POWER RATIO (dBc)
SINGLE QPSK CHANNEL
–28 GAIN CODE 42 (14dB)
CHANNEL WIDTH = 6.4MHz
–32 DRIVEN CHANNEL CENTER = 42 MHz
ADJACENT CHANNEL WIDTH = 6.4 MHz
–36 ADJACENT CHANNEL CENTER = 48.4 MHz
08707-018
ADJACENT CHANNEL POWER RATIO (dBc)
–24
ADA4320-1
APPLICATIONS INFORMATION
Table 7. Data-Word for Setting Current and Gain Levels
Varying distances between the CPE and the cable modem
termination system (CMTS), as well as diplexers and splitters
that may exist in the signal path, require the amplifier to
provide a wide range of output power. The combination of a
high output level, excellent linearity, and 59 dB gain range of the
ADA4320-1 enables the CPE to overcome inline losses and
ensures adequate signal strength at the upstream termination.
CIRCUIT DESCRIPTION
In power-up mode, the ADA4320-1 comprises three analog
functions. The input amplifier (preamp) can be used single-ended
or balanced (differential). If the input is used in the balanced
configuration, it is imperative that the input signals be 180° out
of phase and of equal amplitude. A Vernier adjustment amplifier
controls the 1 dB gain steps.
The digital attenuator (DA) stage provides coarse adjustment in
6 dB steps. It also scales the current supplied to the output stage.
Both the preamp and DA are differential (balanced) to improve
power supply rejection and linearity.
CL
3
2
1
0
Gain[5:0]
(Hex)
3C to 01
3C to 01
3C to 01
3C to 01
Cain
Code
(Dec)
60 to 01
60 to 01
60 to 01
60 to 01
Typical
Gain (dB)
+32 to −27
+32 to −27
+32 to −27
+32 to −27
CURRENT LEVEL AND GAIN ADJUSTMENT
Gain adjustment and current scaling allow the PA to achieve the
high output levels and linearity required for multiple-channel
DOCSIS 3.0 compliance, while offering significantly reduced
power consumption in single-channel and lifeline battery-backup
modes of operation.
There are two methods of adjusting the output stage current of
the ADA4320-1. The first is performed automatically, lowering
output current as attenuation is increased (gain is reduced).
As shown in Figure 23, for every 6 dB reduction in gain, output
stage current is decreased. At higher gain settings, this is more
pronounced. At maximum gain and maximum current level,
a step down of 6 dB reduces the supply current by 33%.
The second method, which allows the user to program one of
four preset current levels (CL3 to CL0) at any gain setting, is
shown by the individual traces in Figure 23.
300
CURRENT
CURRENT
CURRENT
CURRENT
GAIN
250
SUPPLY CURRENT (mA)
The ADA4320-1 is controlled via a unidirectional, 3-wire serial
interface (SPI-compatible) consisting of CLK, DATEN, and SDATA
signals. An 8-bit data-word containing the output stage current
level (Bits[7:6]) and desired gain code (Bits[5:0]) is clocked into
the SDATA port, MSB first.
CL[7:6]
(Bin)
11
10
01
00
The sequence of loading the SDATA register starts on the falling
edge of the DATEN pin, which activates the CLK line. Data on
the SDATA line is clocked into the serial shift register on the
rising edge of CLK, MSB first. The data-word is latched into
the attenuator core on the rising edge of DATEN. Serial interface
timing for the ADA4320-1 is shown in Figure 2 and Figure 3.
The differential current is output from the DA to the output stage.
The output stage, with its 300 Ω balanced output impedance,
maintains proper matching to a 75 Ω load when used with a
2:1 (turns ratio) balun transformer.
PROGRAMMING
Typical
Current
(mA)
260 to 77
235 to 73
210 to 70
180 to 65
The programmable current level (CL) range of the ADA4320-1 is
CL3 (highest) to CL0 (lowest). The programmable gain range is
+32 dB (Gain Code 60) to −27 dB (Gain Code 01), in steps of 1 dB
per least significant bit (LSB), providing a total gain range of 59 dB.
Rev. 0 | Page 11 of 16
LEVEL
LEVEL
LEVEL
LEVEL
30
3
2
1
0
18
200
6
150
–6
100
–18
50
0
12
24
36
48
GAIN CODE
Figure 23. Gain and Current Scaling
–30
60
GAIN (dB)
The ADA4320-1 is primarily intended for use as the reverse
channel power amplifier (PA) in DOCSIS® 3.0 customer premises
equipment (CPE), including cable modems, E-MTAs, and
DOCSIS-enabled set-top boxes. The signals are typically QPSK or
QAM waveforms generated by the upstream modulator and DAC.
To sufficiently attenuate DAC images, a low-pass reconstruction
filter is recommended between the DAC output and the
ADA4320-1. A differential filter is preferred, and its output
impedance should match the 640 Ω input impedance of the
ADA4320-1.
08707-024
GENERAL APPLICATIONS
ADA4320-1
POWER SAVING FEATURES
OUTPUT BIAS, IMPEDANCE, AND TERMINATION
The ADA4320-1 incorporates three distinct methods for
reducing power consumption that include the following:
The output stage of the ADA4320-1 requires a bias of 5 V.
The 5 V power supply should be applied to the center tap of
the output transformer through a 100 nH series inductor. This
supply should also be decoupled with a 0.1 μF capacitor, as shown
in Figure 24.
•
Transmit disable for between-burst periods
•
Sleep (shutdown) mode
•
Output stage current scaling
The asynchronous TXEN pin is used to place the ADA4320-1
into between-burst mode. In this reduced current state, the
300 Ω differential output impedance is maintained. Applying
Logic 0 to the TXEN pin deactivates the amplifier, providing
up to 95% reduction in consumed power. For 5 V operation at
maximum gain and current level, supply current is typically
reduced from 260 mA to 12 mA. In this mode of operation,
between-burst noise is minimized and over 100 dB of input to
output isolation is achieved.
Additionally, the ADA4320-1 incorporates an asynchronous
SLEEP pin that can be used to further reduce supply current to
approximately 12 μA. Applying Logic 0 to the SLEEP pin places
the amplifier into sleep mode.
Entering/exiting sleep mode can result in a transient voltage at the
output of the amplifier. It is recommended to perform transitions
on the SLEEP pin with TXEN held low.
Additional power savings are possible by optimizing the output
stage current for different operating conditions. Typically, at
lower frequencies (5 MHz to 42 MHz), the full specified output
can be maintained in CL0 (see Figure 13 and Figure 16). For lower
input levels, the same is true, as shown in Figure 17 and Figure 20.
For per-channel output levels less than 65 dBmV (QPSK) and
50 dBmV (4× QAM64), the ADA4320-1 can maintain an ACPR
of better than −60 dBc (see Figure 18 and Figure 21) at Current
Level 0 (CL0). At higher gain settings, operating in CL0 reduces
current consumption by 30%, compared to operating in CL3.
As an example, operating in CL0, the ADA4320-1 can drive a
single QPSK channel at 61 dBmV, at maximum gain, maintaining
a worst-case ACPR of −66 dBc. It does this while drawing only
180 mA from a 5 V supply.
INPUT BIAS, IMPEDANCE, AND TERMINATION
The VIN+ and VIN− inputs have a dc bias level of VCC/2;
therefore, the input signal should be ac-coupled as seen in the
typical application circuit (see Figure 24). The differential input
impedance of the ADA4320-1 is approximately 640 Ω, and the
single-ended input is 320 Ω. The ADA4320-1 exhibits optimum
performance when driven with a balanced (differential) signal.
The output impedance of the ADA4320-1 is 300 Ω differential,
regardless of whether the amplifier is in transmit enable, transmit
disable, or sleep mode. This, when combined with a 4:1 impedance
transformer, provides a 75 Ω output match and eliminates the
need for external back termination resistors. If the output signal
is being evaluated using standard 50 Ω test equipment, a minimum
loss 75 Ω to 50 Ω pad should be used to provide the test circuit
with the proper impedance match.
POWER SUPPLY
The 5 V supply should be delivered to each of the VCC pins via
a low impedance power bus. The power bus should be decoupled
with a 10 μF tantalum capacitor located close to the ADA4320-1.
Additionally, the VCC pins require decoupling to ground with
ceramic chip capacitors located close to the pins. Pin 24 (COMP),
should also be decoupled. The ideal printed circuit board (PCB)
has a low impedance ground plane covering all unused portions
of the board, except in areas of the board where input and output
traces are in close proximity to the ADA4320-1 and the output
transformer. All device GND pins, as well as the exposed pad,
must contact the PCB ground plane to ensure proper grounding
of all internal nodes.
SIGNAL INTEGRITY LAYOUT CONSIDERATIONS
Careful attention to PCB layout details can prevent problems
due to board parasitics. Proper RF design techniques are highly
recommended. All balanced input/output traces should be kept
as short as possible. This minimizes parasitic capacitance and
inductance, which is most critical between the outputs of the
ADA4320-1 and the 4:1 output transformer. It is also recommended
that all balanced signal paths be symmetrical in length and width.
Additionally, input and output traces should be adequately spaced
to minimize coupling (crosstalk) through the board. Following
these guidelines optimizes the overall performance of the
ADA4320-1 in all applications.
INITIAL POWER-UP
When supply voltage is applied to the ADA4320-1, the gain of
the amplifier is initially undetermined. During amplifier powerup, the TXEN pin should be held low (Logic 0) to prevent forward
signal transmission. Gain must then be set to the desired level,
followed by TXEN driven high. Forward signal transmission is
enabled at the resultant gain level.
Rev. 0 | Page 12 of 16
ADA4320-1
RAMP PIN FEATURE
OUTPUT TRANSFORMER
The RAMP pin (Pin 6) can be optionally used to control the
length of the burst on and off transients. By default, leaving the
RAMP pin unconnected results in a transient that is fully compliant
with DOCSIS 3.0. Adding capacitance to the RAMP pin slows
the dissipation even more.
Matching the 300 Ω differential output impedance to unbalanced
75 Ω requires a 4:1 impedance (2:1 turns) ratio transformer.
The transformer should have minimal insertion loss over the
5 MHz to 85 MHz band and have a maximum dc current rating
of at least 200 mA.
Characterization of the ADA4320-1 was performed using a
Coilcraft PWB-4-BL surface-mount wide-band RF transformer.
Alternate choices for the output transformer are the Toko
458PT-1565 and the Tyco Electronics (M/A-COM) ABACT0018.
5V
10µF
+
100pF
TO TUNER
OR SPLITTER
TRANSMIT
ENABLE/DISABLE
CONTROL
GND
GND
VCC
VCC
VCC
RAMP
VIN–
ADA4320-1
DIPLEXER
20
2:1*
GND
VOUT–
GND
GND
GND
VOUT+
F-CONNECTOR
UPSTREAM
VOUT–
VIN+
SLEEP
DOWNSTREAM
0.1µF
0.1µF
13
3-WIRE
(SPI-COMPATIBLE)
CONTROL
*COILCRAFT PWB-4-BL
ALTERNATES: TOKO 458PT-1565
TYCO MABACT0018
POWER-DOWN
CONTROL
Figure 24. Typical Application
Rev. 0 | Page 13 of 16
08707-025
TXEN
VOUT+
CLK
0.1µF
COMP
GND
DATEN
LPF
GND
SDATA
DAC
100nH
1
8
QPSK/QAM
BURST
MODULATOR
0.1µF
ADA4320-1
OUTLINE DIMENSIONS
2.75
2.65
2.50
4.00 BSC
PIN 1
INDICATOR
20
PIN 1
INDICATOR
1
19
5.00 BSC
0.50
BSC
3.75
3.65
3.50
EXPOSED
PAD
7
13
1.00
0.90
0.80
0.30
0.25
0.20
SEATING
PLANE
0.50
0.40
0.30
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
8
12
BOTTOM VIEW
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
122409-B
TOP VIEW
(Chamfer 0.225)
24
Figure 25. 24-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
4 mm × 5 mm Body, Very Thin Quad
(CP-24-5)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1
ADA4320-1ACPZ-R2
ADA4320-1ACPZ-R7
ADA4320-1ACPZ-RL
1
Temperature Range
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Package Description
24-Lead Lead Frame Chip Scale Package (LFCSP_VQ)
24-Lead Lead Frame Chip Scale Package (LFCSP_VQ)
24-Lead Lead Frame Chip Scale Package (LFCSP_VQ)
Z = RoHS Compliant Part.
Rev. 0 | Page 14 of 16
Package Option
CP-24-5
CP-24-5
CP-24-5
Ordering
Quantity
250
1,500
5,000
ADA4320-1
NOTES
Rev. 0 | Page 15 of 16
ADA4320-1
NOTES
©2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D08707-0-4/10(0)
Rev. 0 | Page 16 of 16
Similar pages