Maxim MAX5054BATA 4a, 20ns, dual mosfet driver Datasheet

19-3348; Rev 2; 9/10
4A, 20ns, Dual MOSFET Drivers
The MAX5054–MAX5057 dual, high-speed MOSFET
drivers source and sink up to 4A peak current. These
devices feature a fast 20ns propagation delay and 20ns
rise and fall times while driving a 5000pF capacitive
load. Propagation delay time is minimized and matched
between the inverting and noninverting inputs and
between channels. High sourcing/sinking peak currents, low propagation delay, and thermally enhanced
packages make the MAX5054–MAX5057 ideal for highfrequency and high-power circuits.
The MAX5054–MAX5057 operate from a 4V to 15V single
power supply and consume 40µA (typ) of supply current
when not switching. These devices have internal logic
circuitry that prevents shoot-through during output state
changes to minimize the operating current at high
switching frequency. The logic inputs are protected
against voltage spikes up to +18V, regardless of the VDD
voltage. The MAX5054A is the only version that has
CMOS input logic levels while the MAX5054B/MAX5055/
MAX5056/MAX5057 have TTL input logic levels.
The MAX5055–MAX5057 provide the combination of dual
inverting, dual noninverting, and inverting/noninverting
input drivers. The MAX5054 feature both inverting and
noninverting inputs per driver for greater flexibility. They
are available in 8-pin TDFN (3mm x 3mm), standard SO,
and thermally enhanced SO packages. These devices
operate over the automotive temperature range of -40°C
to +125°C.
Applications
Features
o 4V to 15V Single Power Supply
o 4A Peak Source/Sink Drive Current
o 20ns (typ) Propagation Delay
o Matching Delay Between Inverting and
Noninverting Inputs
o Matching Propagation Delay Between Two
Channels
o VDD / 2 CMOS Logic Inputs (MAX5054AATA)
o TTL Logic Inputs
(MAX5054B/MAX5055/MAX5056/MAX5057)
o 0.1 x VDD (CMOS) and 0.3V (TTL) Logic-Input
Hysteresis
o Up to +18V Logic Inputs (Regardless of VDD
Voltage)
o Low Input Capacitance: 2.5pF (typ)
o 40µA (typ) Quiescent Current
o -40°C to +125°C Operating Temperature Range
o 8-Pin TDFN and SO Packages
Ordering Information
PART
TEMP
RANGE
PINPACKAGE
TOP
MARK
Power MOSFET Switching
Motor Control
MAX5054AATA+
-40°C to +125°C 8 TDFN-EP*
AGS
Switch-Mode Power Supplies
Power-Supply Modules
MAX5054AATA/V+
-40°C to +125°C 8 TDFN-EP*
AGR
MAX5054BATA+
-40°C to +125°C 8 TDFN-EP*
AGR
MAX5055AASA+
-40°C to +125°C 8 SO-EP*
—
MAX5055BASA+
-40°C to +125°C 8 SO
—
MAX5056AASA+
-40°C to +125°C 8 SO-EP*
—
MAX5056BASA+
-40°C to +125°C 8 SO
—
MAX5057AASA+
-40°C to +125°C 8 SO-EP*
—
MAX5057BASA+
-40°C to +125°C 8 SO
*EP = Exposed pad.
/VDenotes an automotive qualified part.
+Denotes a lead(Pb)-free/RoHS-compliant package.
—
DC-DC Converters
Typical Operating Circuit
VOUT
VIN
MAX5054
VDD
INA+
OUTA
INA-
INB+
OUTB
PWM IN
INB-
Selector Guide and Pin Configurations appear at end of
data sheet.
GND
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX5054–MAX5057
General Description
MAX5054–MAX5057
4A, 20ns, Dual MOSFET Drivers
ABSOLUTE MAXIMUM RATINGS
8-Pin SO-EP (derate 19.2mW/°C above +70°C)… ........1538mW
Junction-to-Case Thermal Resistance (θJC) ......................6°C/W
8-Pin SO (derate 5.9mW/°C above +70°C)… ..................471mW
Junction-to-Case Thermal Resistance (θJC) ....................40°C/W
Operating Temperature Range..............................-40°C to +125°C
Storage Temperature Range .................................-65°C to +150°C
Junction Temperature ...........................................................+150°C
Lead Temperature (soldering, 10s)......................................+300°C
Soldering Temperature (reflow)............................................+260°C
(Voltages referenced to GND.)
VDD...............................................................................-0.3V to +18V
INA+, INA-, INB+, INB- ...............................................-0.3V to +18V
OUTA, OUTB...................................................-0.3V to (VDD + 0.3V)
OUTA, OUTB Short-Circuit Duration ........................................10ms
Continuous Source/Sink Current at OUT_ (PD < PDMAX) .....200mA
Continuous Power Dissipation (TA = +70°C)
8-Pin TDFN-EP (derate 18.2mW/°C above +70°C)........1454mW
Junction-to-Case Thermal Resistance (θJC) ...................8.3°C/W
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VDD = 4V to 15V, TA = -40°C to +125°C, unless otherwise noted. Typical values are at VDD = 15V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
15
V
3.85
V
POWER SUPPLY
VDD Operating Range
VDD Undervoltage Lockout
VDD
UVLO
4
VDD rising
3.00
VDD Undervoltage Lockout
Hysteresis
VDD Undervoltage Lockout to
Output Delay
VDD rising
IDD
INA- = INB- = VDD,
INA+ = INB+ = 0V
(not switching)
3.50
200
mV
12
µs
VDD = 4V
28
55
VDD = 15V
40
75
2.4
4
µA
VDD Supply Current
IDD-SW
INA- = 0V, INB+ = VDD = 15V,
INA+ = INB- both channels switching at
250kHz, CL = 0F
1
mA
DRIVER OUTPUT (SINK)
Driver Output Resistance Pulling
Down
Peak Output Current (Sinking)
RON-N
IPK-N
Output-Voltage Low
Latchup Protection
VDD = 15V,
IOUT_ = -100mA
TA = +25°C
1.1
1.8
TA = +125°C
1.5
2.4
VDD = 4.5V,
IOUT_ = -100mA
TA = +25°C
2.2
3.3
TA = +125°C
3.0
4.5
VDD = 15V, CL = 10,000pF
IOUT_ = -100mA
ILUP
4
A
VDD = 4.5V
0.45
VDD = 15V
0.24
Reverse current IOUT_ (Note 2)
Ω
400
V
mA
DRIVER OUTPUT (SOURCE)
Driver Output Resistance Pulling
Up
RON-P
Peak Output Current (Sourcing)
IPK-P
2
VDD = 15V,
IOUT_ = 100mA
TA = +25°C
1.5
2.1
TA = +125°C
1.9
2.75
VDD = 4.5V,
IOUT_ = 100mA
TA = +25°C
2.75
4
TA = +125°C
3.75
5.5
VDD = 15V, CL = 10,000pF
4
_______________________________________________________________________________________
Ω
A
4A, 20ns, Dual MOSFET Drivers
(VDD = 4V to 15V, TA = -40°C to +125°C, unless otherwise noted. Typical values are at VDD = 15V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
Output-Voltage High
CONDITIONS
MIN
VDD = 4.5V
VDD 0.55
VDD = 15V
VDD 0.275
TYP
MAX
UNITS
V
IOUT_ = 100mA
LOGIC INPUT (Note 3)
MAX5054A
Logic 1 Input Voltage
Logic 0 Input Voltage
VIH
VIL
MAX5054B/MAX5055/MAX5056/MAX5057
(Note 4)
0.7 x
VDD
V
2.1
0.3 x
VDD
MAX5054A
MAX5054B/MAX5055/MAX5056/MAX5057
Logic-Input Hysteresis
VHYS
0.8
0.1 x
VDD
MAX5054A
MAX5054B/MAX5055/MAX5056/MAX5057
Logic-Input-Current Leakage
Input Capacitance
INA+, INB+, INA-, INB- = 0V or VDD
V
V
0.3
-1
CIN
+0.1
+1
2.5
µA
pF
SWITCHING CHARACTERISTICS FOR VDD = 15V (Figure 1)
OUT_ Rise Time
OUT_ Fall Time
tR
tF
CL = 1000pF
4
CL = 5000pF
18
CL = 10,000pF
32
CL = 1000pF
4
CL = 5000pF
15
CL = 10,000pF
ns
ns
26
Turn-On Delay Time
tD-ON
CL = 10,000pF (Note 2)
10
20
34
ns
Turn-Off Delay Time
tD-OFF
CL = 10,000pF (Note 2)
10
20
34
ns
SWITCHING CHARACTERISTICS FOR VDD = 4.5V (Figure 1)
OUT_ Rise Time
OUT_ Fall Time
tR
tF
CL = 1000pF
7
CL = 5000pF
37
CL = 10,000pF
85
CL = 1000pF
7
CL = 5000pF
30
CL = 10,000pF
75
ns
ns
Turn-On Delay Time
tD-ON
CL = 10,000pF (Note 2)
18
35
70
ns
Turn-Off Delay Time
tD-OFF
CL = 10,000pF (Note 2)
18
35
70
ns
_______________________________________________________________________________________
3
MAX5054–MAX5057
ELECTRICAL CHARACTERISTICS (continued)
ELECTRICAL CHARACTERISTICS (continued)
(VDD = 4V to 15V, TA = -40°C to +125°C, unless otherwise noted. Typical values are at VDD = 15V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
MATCHING CHARACTERISTICS
Mismatch Propagation Delays from
Inverting and Noninverting Inputs
to Output
∆tON-OFF
Mismatch Propagation Delays
Between Channel A and Channel B
∆tA-B
VDD = 15V, CL = 10,000pF
2
VDD = 4.5V, CL = 10,000pF
4
VDD = 15V, CL = 10,000pF
1
VDD = 4.5V, CL = 10,000pF
2
ns
ns
All devices are 100% tested at TA = +25°C. Specifications over -40°C to +125°C are guaranteed by design.
Limits are guaranteed by design, not production tested.
The logic-input thresholds are tested at VDD = 4V and VDD = 15V.
TTL compatible with reduced noise immunity.
Note 1:
Note 2:
Note 3:
Note 4:
Typical Operating Characteristics
(TA = +25°C, unless otherwise noted.)
TA = +125°C
40
TA = +25°C
20
40
30
TA = +25°C
20
10
10
0
10
12
14
8
10
12
14
PROPAGATION DELAY TIME,
HIGH-TO-LOW vs. SUPPLY VOLTAGE
(CL = 5000pF)
IDD-SW SUPPLY CURRENT
vs. SUPPLY VOLTAGE
20
4
2
8
10
MAX5054 toc03
12
14
16
DUTY CYCLE = 50%
VDD = 15V, CL = 4700pF
1 CHANNEL SWITCHING
90
80
70
1MHz
60
50
500kHz
40
30
50kHz
100kHz
10
0
0
6
10
20
50kHz
100kHz
8
100
MAX5054 toc05
500kHz
1
TA = -40°C
6
SUPPLY CURRENT vs. SUPPLY VOLTAGE
1MHz
3
4
SUPPLY VOLTAGE (V)
DUTY CYCLE = 50%
VDD = 15V, CL = 0
1 CHANNEL SWITCHING
5
16
SUPPLY CURRENT (mA)
TA = +25°C
30
6
IDD-SW SUPPLY CURRENT (mA)
MAX5054 toc04
40
0
12
SUPPLY VOLTAGE (V)
4
6
SUPPLY VOLTAGE (V)
TA = +125°C
4
TA = -40°C
0
4
16
SUPPLY VOLTAGE (V)
10
20
MAX5054 toc06
8
60
50
TA = +25°C
30
TA = -40°C
0
6
40
10
TA = -40°C
4
TA = +125°C
50
PROPAGATION DELAY (ns)
50
FALL TIME (ns)
RISE TIME (ns)
TA = +125°C
60
MAX5054 toc02
50
30
60
MAX5054 toc01
60
PROPAGATION DELAY TIME,
LOW-TO-HIGH vs. SUPPLY VOLTAGE
(CL = 5000pF)
FALL TIME vs. SUPPLY VOLTAGE
(CL = 5000pF)
RISE TIME vs. SUPPLY VOLTAGE
(CL = 5000pF)
PROPAGATION DELAY (ns)
MAX5054–MAX5057
4A, 20ns, Dual MOSFET Drivers
14
16
4
6
8
10
12
SUPPLY VOLTAGE (V)
14
16
4
6
8
10
12
SUPPLY VOLTAGE (V)
_______________________________________________________________________________________
14
16
4A, 20ns, Dual MOSFET Drivers
2.5
2.0
1.5
MAX5054AATA
(CMOS INPUT)
9
8
7
VIN RISING
6
5
4
VIN FALLING
3
2
3.0
INPUT THRESHOLD VOLTAGE (V)
3.0
10
MAX5054 toc08
VDD = 15V,
f = 250kHz, CL = 0
DUTY CYCLE = 50%
BOTH CHANNELS SWITCHING
INPUT THRESHOLD VOLTAGE (V)
SUPPLY CURRENT (mA)
MAX5054 toc07
4.0
3.5
INPUT THRESHOLD VOLTAGE
vs. SUPPLY VOLTAGE
INPUT THRESHOLD VOLTAGE
vs. SUPPLY VOLTAGE
MAX5054 toc09
IDD-SW SUPPLY CURRENT
vs. TEMPERATURE
TTL INPUT VERSIONS
2.5
VIN RISING
2.0
1.5
1.0
VIN FALLING
0.5
1
1.0
-25
0
25
50
75
100
4
6
8
10
12
4
16
14
10
12
14
SUPPLY CURRENT vs. LOGIC-INPUT
VOLTAGE (INPUT LOW-TO-HIGH)
SUPPLY CURRENT vs. LOGIC-INPUT
VOLTAGE (INPUT HIGH-TO-LOW)
SUPPLY CURRENT vs. LOGIC-INPUT
VOLTAGE (INPUT LOW-TO-HIGH)
200
MAX5054AATA (CMOS INPUT)
VDD = 15V
4
SUPPLY CURRENT (mA)
SUPPLY CURRENT (µA)
400
300
200
100
100
2
4
6
8
10
12
14
0
16
3
2
1
0
0
MAX5054 toc12
TTL INPUT VERSIONS
VDD = 15V
16
5
MAX5054 toc11
500
MAX5054 toc10
300
2
4
6
8
10
12
14
0
16
0
2
4
6
8
10
12
14
16
LOGIC-INPUT VOLTAGE (V)
LOGIC-INPUT VOLTAGE (V)
LOGIC-INPUT VOLTAGE (V)
SUPPLY CURRENT vs. LOGIC-INPUT
VOLTAGE (INPUT HIGH-TO-LOW)
DELAY MISMATCH BETWEEN IN_+
AND IN_- TO OUT_ vs. TEMPERATURE
DELAY MISMATCH BETWEEN IN_+
AND IN_- TO OUT_ vs. TEMPERATURE
3
2
1
2
OUTPUT RISING
0
-2
-4
2
4
6
8
10
12
LOGIC-INPUT VOLTAGE (V)
14
16
4
OUTPUT RISING
2
0
-2
OUTPUT FALLING
-4
MAX5054AATA (CMOS INPUT)
VDD = 4.5V, CL = 10,000pF
MAX5054AATA (CMOS INPUT)
VDD = 15V, CL = 10,000pF
-6
-6
0
6
MAX5054 toc15
4
DELAY MISMATCH (ns)
4
OUTPUT FALLING
DELAY MISMATCH (ns)
MAX5054AATA (CMOS INPUT)
VDD = +15V
MAX5054 toc14
6
MAX5054 toc13
5
0
8
SUPPLY VOLTAGE (V)
400
0
6
SUPPLY VOLTAGE (V)
TTL INPUT VERSIONS
VDD = 15V
SUPPLY CURRENT (µA)
125
TEMPERATURE (°C)
500
SUPPLY CURRENT (mA)
0
0
-50
-50
-25
0
25
50
75
TEMPERATURE (°C)
100
125
-50
-25
0
25
50
75
100
125
TEMPERATURE (°C)
_______________________________________________________________________________________
5
MAX5054–MAX5057
Typical Operating Characteristics (continued)
(TA = +25°C, unless otherwise noted.)
Typical Operating Characteristics (continued)
(TA = +25°C, unless otherwise noted.)
DELAY MISMATCH BETWEEN 2 CHANNELS
vs. TEMPERATURE
DELAY MISMATCH BETWEEN 2 CHANNELS
vs. TEMPERATURE
3
1
0
-1
VDD = 15V, CL = 10,000pF
3
DELAY MISMATCH (ns)
OUTPUT FALLING
OUTPUT RISING
MAX5054 toc17
VDD = 4.5V, CL = 10,000pF
2
4
MAX5054 toc16
4
DELAY MISMATCH (ns)
MAX5054–MAX5057
4A, 20ns, Dual MOSFET Drivers
OUTPUT RISING
2
1
0
-1
-2
-2
-3
-3
OUTPUT FALLING
-4
-4
-50
-25
0
25
50
75
100
-50
125
-25
0
25
50
75
100
125
TEMPERATURE (°C)
TEMPERATURE (°C)
LOGIC-INPUT VOLTAGE vs. OUTPUT VOLTAGE
(VDD = 4V, CL = 5000pF)
MAX5054 toc18
LOGIC-INPUT VOLTAGE vs. OUTPUT VOLTAGE
(VDD = 4V, CL = 10,000pF)
MAX5054 toc19
IN_2V/div
IN_2V/div
OUT_
2V/div
MAX5055 (TTL INPUT)
OUT_
2V/div
MAX5055 (TTL INPUT)
20ns/div
40ns/div
LOGIC-INPUT VOLTAGE vs. OUTPUT VOLTAGE
(VDD = 4V, CL = 5000pF)
LOGIC-INPUT VOLTAGE vs. OUTPUT VOLTAGE
(VDD = 4V, CL = 10,000pF)
MAX5054 toc21
MAX5054 toc20
IN_2V/div
IN_2V/div
OUT_
2V/div
OUT_
2V/div
MAX5055 (TTL INPUT)
20ns/div
6
MAX5055 (TTL INPUT)
40ns/div
_______________________________________________________________________________________
4A, 20ns, Dual MOSFET Drivers
LOGIC-INPUT VOLTAGE vs. OUTPUT VOLTAGE
(VDD = 15V, CL = 5000pF)
MAX5054 toc22
LOGIC-INPUT VOLTAGE vs. OUTPUT VOLTAGE
(VDD = 15V, CL = 10,000pF)
MAX5054 toc23
IN_2V/div
IN_2V/div
OUT_
5V/div
OUT_
5V/div
MAX5055
MAX5055
20ns/div
40ns/div
LOGIC-INPUT VOLTAGE vs. OUTPUT VOLTAGE
(VDD = 15V, CL = 5000pF)
LOGIC-INPUT VOLTAGE vs. OUTPUT VOLTAGE
(VDD = 15V, CL = 10,000pF)
MAX5054 toc24
MAX5054 toc25
IN_2V/div
IN_2V/div
OUT_
5V/div
OUT_
5V/div
MAX5055
MAX5055
20ns/div
40ns/div
VDD vs. OUTPUT VOLTAGE
VDD vs. OUTPUT VOLTAGE
MAX5054 toc26
MAX5054 toc27
VDD
5V/div
OUTA
5V/div
MAX5055
INA- = INB- = GND
CLA = CLB = 10,000pF
VDD
5V/div
OUTA
5V/div
OUTB
5V/div
MAX5055
INA- = INB- = GND
CLA = CLB = 10,000pF
2ms/div
OUTB
5V/div
2ms/div
_______________________________________________________________________________________
7
MAX5054–MAX5057
Typical Operating Characteristics (continued)
(TA = +25°C, unless otherwise noted.)
MAX5054–MAX5057
4A, 20ns, Dual MOSFET Drivers
Pin Descriptions
MAX5054
PIN
NAME
FUNCTION
1
INA-
Inverting Logic-Input Terminal for Driver A. Connect to GND when not used.
2
INB-
Inverting Logic-Input Terminal for Driver B. Connect to GND when not used.
3
GND
Ground
4
OUTB
5
VDD
6
OUTA
Driver A Output. Sources or sinks current for channel A to turn the external MOSFET on or off.
7
INB+
Noninverting Logic-Input Terminal for Driver B. Connect to VDD when not used.
8
INA+
Noninverting Logic-Input Terminal for Driver A. Connect to VDD when not used.
—
EP
Driver B Output. Sources or sinks current for channel B to turn the external MOSFET on or off.
Power Supply. Bypass to GND with one or more 0.1µF ceramic capacitors.
Exposed Pad. Internally connected to GND. Do not use the exposed pad as the only electrical
ground connection.
MAX5055/MAX5056/MAX5057
PIN
NAME
FUNCTION
MAX5055
MAX5056
MAX5057
1, 8
1, 8
1, 8
N.C.
No Connection. Not internally connected.
2
—
2
INA-
Inverting Logic-Input Terminal for Driver A. Connect to GND if not used.
8
3
3
3
GND
Ground
4
—
—
INB-
Inverting Logic-Input Terminal for Driver B. Connect to GND if not used.
5
5
5
OUTB
Driver B Output. Sources or sinks current for channel B to turn the external
MOSFET on or off.
6
6
6
VDD
Power Supply. Bypass to GND with one or more 0.1µF ceramic capacitors.
7
7
7
OUTA
Driver A Output. Sources or sinks current for channel A to turn the external
MOSFET on or off.
—
4
4
INB+
Noninverting Logic-Input Terminal for Driver B. Connect to VDD if not used.
—
2
—
INA+
Noninverting Logic-Input Terminal for Driver A. Connect to VDD if not used.
—
—
—
EP
Exposed Pad. Internally connected to GND. Do not use the exposed pad as
the only electrical ground connection.
_______________________________________________________________________________________
4A, 20ns, Dual MOSFET Drivers
MAX5054–MAX5057
IN_+
VIH
VIL
VDD
MAX5055
MAX5056
MAX5057
90%
OUT_
tD-OFF1
tD-ON1
IN_+
tF
IN_-
P
BREAKBEFOREMAKE
CONTROL
10%
tR
OUT_
N
VIH
VIL
tD-OFF2
tD-ON2
GND
RISING MISMATCH = tD-ON2 - tD-ON1
FALLING MISMATCH = tD-OFF2 - tD-OFF1
NONINVERTING INPUT DRIVER
Figure 1. Timing Diagram
VDD
MAX5055
MAX5056
MAX5057
VDD
MAX5054
IN_-
P
BREAKBEFOREMAKE
CONTROL
IN_+
P
BREAKBEFOREMAKE
CONTROL
IN_OUT_
OUT_
N
N
GND
GND
INVERTING INPUT DRIVER
Figure 2. MAX5054 Block Diagram (1 Driver)
Detailed Description
VDD Undervoltage Lockout (UVLO)
The MAX5054–MAX5057 have internal undervoltage
lockout for VDD. When VDD is below the UVLO threshold, OUT_ is low, independent of the state of the inputs.
The undervoltage lockout is typically 3.5V with 200mV
typical hysteresis to avoid chattering. When VDD rises
above the UVLO threshold, the outputs go high or low
depending upon the logic-input levels. Bypass VDD
using low-ESR ceramic capacitors for proper operation
(see the Applications Information section).
Figure 3. MAX5055/MAX5056/MAX5057 Functional Diagrams
(1 Driver)
Logic Inputs
The MAX5054B–MAX5057 have TTL-compatible logic
inputs, while the MAX5054A is a CMOS logic-input driver. The logic-input signals can be independent of the
VDD voltage. For example, the device can be powered
by a 5V supply while the logic inputs are provided from
CMOS logic. Also, the logic inputs are protected against
the voltage spikes up to 18V, regardless of the VDD voltage. The TTL and CMOS logic inputs have 300mV and
0.1 x VDD hysteresis, respectively, to avoid possible double pulsing during transition. The low 2.5pF input capacitance reduces loading and increases switching speed.
_______________________________________________________________________________________
9
MAX5054–MAX5057
4A, 20ns, Dual MOSFET Drivers
Table 1. MAX5054 Truth Table
INA+/INB+
INA-/INB-
OUTA/OUTB
Low
Low
Low
Low
High
Low
High
Low
High
High
High
Low
Table 2. MAX5055/MAX5056/MAX5057
Truth Table
VDD
MAX5054A
PWM
INPUT
INA+
OFF
ON
INA-
OUTA
GND
NONINVERTING
IN_+
OUT_
Low
Low
High
High
INVERTING
IN_-
OUT_
Low
High
High
Low
The logic inputs are high impedance and must not be left
floating. If the inputs are left open, OUT_ can go to an
undefined state as soon as VDD rises above the UVLO
threshold. Therefore, the PWM output from the controller
must assume proper state when powering up the device.
The MAX5054 has two logic inputs per driver providing
greater flexibility in controlling the MOSFET. Use IN_+ for
noninverting logic and IN_- for inverting logic operation.
Connect IN_+ to V DD and IN_- to GND if not used.
Alternatively, the unused input can be used as an
ON/OFF function. Use IN_+ for active-low shutdown logic
and IN_- for active-high shutdown logic (see Figure 4).
See Table 1 for all possible input combinations.
Driver Output
The MAX5054–MAX5057 have low RDS(ON) p-channel
and n-channel devices (totem pole) in the output stage
for the fast turn-on and turn-off high gate-charge switching MOSFETs. The peak source or sink current is typically
4A. The OUT_ voltage is approximately equal to VDD
when in high state and is ground when in low state. The
driver R DS(ON) is lower at higher V DD , thus higher
source-/sink-current capability and faster switching
speeds. The propagation delays from the noninverting
and inverting logic inputs to outputs are matched to 2ns.
The break-before-make logic avoids any cross-conduction between the internal p- and n-channel devices, and
eliminates shoot-through currents reducing the quiescent
supply current.
10
Figure 4. Unused Input as an ON/OFF Function (1/2 MAX5054A)
Applications Information
RLC Series Circuit
The driver’s RDS(ON) (RON), internal bond and lead
inductance (LP), trace inductance (LS), gate inductance
(LG), and gate capacitance (CG) form a series RLC
circuit with a second-order characteristic equation. The
series RLC circuit has an undamped natural frequency
(ϖ0) and a damping ratio (ζ) where:
ϖ0 =
1
(LP + LS + LG ) × CG
RON
ξ=
2 ×
(LP + LS + LG )
CG
The damping ratio needs to be greater than 0.5 (ideally 1)
to avoid ringing. Add a small resistor (RGATE) in series
with the gate when driving a very low gate-charge
MOSFET, or when the driver is placed away from the
MOSFET. Use the following equation to calculate the
series resistor:
RGATE ≥
(LP + LS + LG )
− RON
CG
LP can be approximated as 3nH and 2nH for SO and
TDFN packages, respectively. LS is on the order of
20nH/in. Verify LG with the MOSFET vendor.
______________________________________________________________________________________
4A, 20ns, Dual MOSFET Drivers
Power Dissipation
Power dissipation of the MAX5054–MAX5057 consists
of three components: caused by the quiescent current,
capacitive charge/discharge of internal nodes, and the
output current (either capacitive or resistive load).
Maintain the sum of these components below the maximum power dissipation limit.
The current required to charge and discharge the internal
nodes is frequency dependent (see the Supply Current
vs. Supply Voltage graph in the Typical Operating
Characteristics). The power dissipation (PQ) due to the
quiescent switching supply current (IDD-SW) per driver
can be calculated as:
PQ = VDD x IDD-SW
For capacitive loads, use the following equation to estimate the power dissipation per driver:
PCLOAD = CLOAD x (VDD)2 x fSW
where CLOAD is the capacitive load, VDD is the supply
voltage, and fSW is the switching frequency.
Calculate the total power dissipation (PT) per driver as
follows:
PT = PQ + PCLOAD
where D (duty cycle) is the fraction of the period the
MAX5054–MAX5057’s output pulls high duty cycle,
RON(MAX) is the maximum on-resistance of the device
with the output high, and ILOAD is the output load current
of the MAX5054–MAX5057.
Layout Information
The MAX5054–MAX5057 MOSFET drivers source and
sink large currents to create very fast rising and falling
edges at the gate of the switching MOSFET. The high
di/dt can cause unacceptable ringing if the trace
lengths and impedances are not well controlled. Use the
following PC board layout guidelines when designing
with the MAX5054–MAX5057:
•
•
•
Place one or more 0.1µF decoupling ceramic
capacitors from VDD to GND as close to the device
as possible. Connect VDD and GND to large copper
areas. Place one bulk capacitor of 10µF (min) on
the PC board with a low resistance path to the VDD
input and GND of the MAX5054–MAX5057.
Two AC current loops form between the device and
the gate of the driven MOSFET. The MOSFET looks
like a large capacitance from gate to source when the
gate pulls low. The active current loop is from the
MOSFET gate to OUT_ of the MAX5054–MAX5057, to
GND of the MAX5054–MAX5057, and to the source of
the MOSFET. When the gate of the MOSFET pulls
high, the active current is from the VDD terminal of the
decoupling capacitor, to V DD of the MAX5054–
MAX5057, to OUT_ of the MAX5054–MAX5057, to the
MOSFET gate, to the MOSFET source, and to the
negative terminal of the decoupling capacitor. Both
charging current and discharging current loops are
important. Minimize the physical distance and the
impedance in these AC current paths.
Keep the device as close to the MOSFET as possible.
•
In a multilayer PC board, the inner layers should
consist of a GND plane containing the discharging
and charging current loops.
•
Pay extra attention to the ground loop and use a
low-impedance source when using a TTL logicinput device. Fast fall time at OUT_ may corrupt the
input during transition.
Use the following equation to estimate the MAX5054–
MAX5057 total power dissipation per driver when driving
a ground-referenced resistive load:
PT = PQ + PRLOAD
PRLOAD = D x RON(MAX) x ILOAD2
______________________________________________________________________________________
11
MAX5054–MAX5057
Supply Bypassing and Grounding
Pay extra attention to bypassing and grounding the
MAX5054–MAX5057. Peak supply and output currents
may exceed 8A when both drivers drive large external
capacitive loads in phase. Supply voltage drops and
ground shifts create forms of negative feedback for
inverters and may degrade the delay and transition times.
Ground shifts due to insufficient device grounding may
also disturb other circuits sharing the same AC ground
return path. Any series inductance in the VDD, OUT_,
and/or GND paths can cause oscillations due to the very
high di/dt when switching the MAX5054–MAX5057 with
any capacitive load. Place one or more 0.1µF ceramic
capacitors in parallel as close to the device as possible to
bypass VDD to GND. Use a ground plane to minimize
ground return resistance and series inductance. Place
the external MOSFET as close as possible to the
MAX5054–MAX5057 to further minimize board inductance and AC path impedance.
MAX5054–MAX5057
4A, 20ns, Dual MOSFET Drivers
Exposed Pad
Both the SO-EP and TDFN-EP packages have an
exposed pad on the bottom of their package. These
pads are internally connected to GND. For the best
thermal conductivity, solder the exposed pad to the
ground plane to dissipate 1.5W and 1.9W in SO-EP and
TDFN-EP packages, respectively. Do not use the
ground-connected pads as the only electrical ground
connection or ground return. Use GND (pin 3) as the
primary electrical ground connection.
Additional Application Circuits
VOUT
VIN
MAX5054
VDD
INA+
OUTA
INA-
MAX5054
VDD
VDD
PWM IN
INA+
INB+
OUTA
INA-
PWM IN
OUTB
PWM IN
INBGND
INB+
OUTB
INBGND
Figure 5. Push-Pull Converter with Synchronous Rectification Drive Using MAX5054
12
______________________________________________________________________________________
2
R27
10Ω
PVIN
REG9
REG5
TP3
3
4
C19
1µF
C18
1000pF
C17
0.33µF
R11
360Ω
R3
2.2kΩ
REG5
LXH
REG5
C6
0.1µF
C3
4.7µF
C4
4.7µF
R15
31.6kΩ
1%
D8
R16
10.5kΩ
1%
C2
390pF
1
TP1
C1
100pF
C5
4700pF
R25
100kΩ
C24
1000pF
+VIN
R21
24.9kΩ
1%
14
13
12
11
10
9
8
7
6
5
4
3
2
1
17
18
19
20
21
22
23
24
25
26
2
1
IC_PADDLE
REG9
R12
100kΩ
1%
R19
475Ω
R23
10Ω
2
VOUT
OUT
FB
4
1
2 65
U3
R17
0.027Ω
1%
D3
1
PVIN
3
4
IN
1
PGND
2
GND
C21
4.7µF
80V
2
2
C34
330pF
8
2
D2
VOUT
3
1
2
4
R24
10Ω
3
2
1 87
5
6
N1 8 7
D7
2
10
2T
8
+VIN
T1
XFRMRH
R22
15kΩ
6
4T
1
5
8T
2
1
XFRMRH
R18
4.7Ω
D5
R13
47Ω
REG9
R5
38.3kΩ
1%
7
N2
R6
1MΩ
1%
+VIN
R7
0Ω
R8
8.2Ω
R2
2.55kΩ
1%
5
SENSE (+) SENSE (-)
TRIM
3
R9
8.2Ω
1
+VIN
R14
270Ω
C9
1µF
DRVB
XFRMRH
C8
4.7µF
+VIN
ON/OFF
D1
R4
1MΩ
1%
C7
0.22µF
C27
0.15µF
C20
220pF
R20
0Ω
29
16
DRVL
15
CS
PGND
DRVDD
DRVB
XFRMRH
DRVH
BST
AVIN
GND
UVLO
STARTUP
27
28
C36
C28
R1
0.22µF
0.047µF 11.5kΩ
1%
VOUT
U2
LXL
LXH
LXVDD
STT
PVIN
REG9
REG5
FB
COMP
CSS
COM
RCFF
SYNCOUT
FLTINT
MAX5051
RCOSC U1 SYNCIN
1
6
5
4
N3
1
7
4
6
INA-
INB+
OUTB
OUTA
1 4
EN
IN
RESET
L1
2.4µH
MAX5054
U4
4
3 GND
2
1
C11
0.47µF
100V
N4
56
C32
1µF
C22
2200pF
2kV
+5V
C23
1000pF
3
2
1 87
1
D4
2
D6
R10
20Ω
2
C35
1µF
C10
0.47µF
100V
3
5
C30
0.1µF
C13
270µF
4V
5V
C25
0.047µF
100V
+5V
5
C26
0.1µF
GND
VDD
INB-
2
8
HOLD
REG9
7
8
N.C. 6
WDI
OUT
INA+
U5
C12
1µF
100V
+VIN
2
N5
3
3
4
5
1
GND
OUT
VCC
U6
CA
AN
2
1
LXH
C33
1µF
10V
R29
1Ω
XFRMRH
VOUT
-VIN
C15
270µF
4V
U1: MAX5051
U2: PS2913-1-M
U3: MAX8515
U4: MAX5054
U5: MAX5023M
U6: PS9715
N1, N2: SI4486
N3, N4: SI4864
N5: BSS123
C31 5V
0.1µF
C14
270µF
4V
C16
3.3µF
+VIN
R28
2kΩ
R26
560Ω
SGND
VOUT
DRVB
MAX5054–MAX5057
REG5
4A, 20ns, Dual MOSFET Drivers
Figure 6. Schematic of a 48V Input, 3.3V at 15A Output Synchronously Rectified, Isolated Power Supply
______________________________________________________________________________________
13
4A, 20ns, Dual MOSFET Drivers
MAX5054–MAX5057
Pin Configurations
TOP VIEW
MAX5054
MAX5055
INA-
1
8
INA+
N.C.
1
8
N.C.
INB-
2
7
INB+
INA-
2
7
OUTA
GND
3
6
OUTA
GND
3
6
VDD
OUTB 4
5
VDD
INB- 4
5
OUTB
TDFN-EP
SO/SO-EP
MAX5056
MAX5057
N.C.
1
8
N.C.
N.C.
1
8
N.C.
INA+
2
7
OUTA
INA-
2
7
OUTA
GND
3
6
VDD
GND
3
6
VDD
INB+ 4
5
OUTB
INB+ 4
5
OUTB
SO/SO-EP
SO/SO-EP
Selector Guide
Chip Information
PROCESS: CMOS
PART
PINPACKAGE
LOGIC INPUT
MAX5054AATA
8 TDFN-EP*
VDD / 2 CMOS Dual Inverting
and Dual Noninverting Inputs
MAX5054BATA
8 TDFN-EP*
TTL Dual Inverting and Dual
Noninverting Inputs
MAX5055AASA
8 SO-EP*
TTL Dual Inverting Inputs
MAX5055BASA
8 SO
TTL Dual Inverting Inputs
MAX5056AASA
8 SO-EP*
TTL Dual Noninverting Inputs
MAX5056BASA
8 SO
TTL Dual Noninverting Inputs
MAX5057AASA
8 SO-EP*
TTL Inverting and
Noninverting Inputs
MAX5057BASA
8 SO
TTL Inverting and
Noninverting Inputs
Package Information
For the latest package outline information and land patterns, go
to www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in
the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE NO.
LAND
PATTERN NO.
8 TDFN-EP
T833+2
21-0137
90-0059
8 SO-EP
S8E+14
21-0111
90-0151
8 SO
S8+4
21-0041
90-0096
*EP = Exposed pad.
14
______________________________________________________________________________________
4A, 20ns, Dual MOSFET Drivers
REVISION
NUMBER
REVISION
DATE
DESCRIPTION
0
8/04
Initial release
1
9/05
Package-related changes
2
9/10
Added automotive part; updated Package Information table
PAGES
CHANGED
0
TBD
1, 2, 14,
15, 16
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 15
© 2010 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products, Inc.
MAX5054–MAX5057
Revision History
Similar pages