TI MAX3318EIDBRG4 2.5-v 460-kbps rs-232 transceiver with â±15-kv esd protection Datasheet

www.ti.com
FEATURES
•
•
•
•
•
•
ESD Protection for RS-232 I/O Pins
– ±15 kV (Human-Body Model)
– ±8 kV (IEC 61000-4-2, Contact Discharge)
– ±15 kV (IEC 61000-4-2, Air-Gap Discharge)
300-µA Operating Supply Current
1-µA Low-Power Standby (With Receivers
Active) Mode
Designed to Transmit at a Data Rate of
460 kbps
Auto-Power-Down Plus Option Features
Flexible Power-Saving Mode
Operates From a Single 2.25-V to 3-V VCC
Supply
MAX3318E
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
SLLS741 – JUNE 2006
DB OR PW PACKAGE
(TOP VIEW)
READY
C1+
V+
C1−
C2+
C2−
V−
DOUT2
RIN2
ROUT2
1
20
2
19
3
18
4
17
5
16
6
15
7
14
8
13
9
12
10
11
FORCEOFF
VCC
GND
DOUT1
RIN1
ROUT1
FORCEON
DIN1
DIN2
INVALID
APPLICATIONS
•
•
•
•
•
•
Battery-Powered Systems
PDAs
Cellular Phones
Notebooks
Hand-Held Equipment
Pagers
DESCRIPTION/ORDERING INFORMATION
The MAX3318E is a dual-driver, dual-receiver, RS-232-compatible transceiver. The device features
auto-power-down plus and enhanced electrostatic discharge (ESD) protection integrated into the chip. Driver
output and receiver input are protected to ±15 kV using the IEC 61000-4-2 Air-Gap Discharge method, ±8 kV
using the IEC 61000-4-2 Contact Discharge method, and ±15 kV using the Human-Body Model (HBM).
The device operates at a data rate of 460 kbps. The transceiver has a proprietary low-dropout driver output
stage, enabling RS-232-compatible operation from a 2.25-V to 3-V supply with a dual charge pump. The charge
pump requires only four 0.1-µF capacitors and features a logic-level output (READY) that asserts when the
charge pump is regulating and the device is ready to begin transmitting.
The MAX3318E achieves a 1-µA supply current using the auto-power-down feature. This device automatically
enters a low-power power-down mode when the RS-232 cable is disconnected or the drivers of the connected
peripherals are inactive for more than 30 s. The device turns on again when it senses a valid transition at any
driver or receiver input. Auto power down saves power without changes to the existing BIOS or operating
system.
This device is available in two space-saving packages: 20-pin SSOP and 20-pin TSSOP.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006, Texas Instruments Incorporated
MAX3318E
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS741 – JUNE 2006
ORDERING INFORMATION
PACKAGE (1)
TA
SSOP – DB
–0°C to 70°C
TSSOP – PW
SSOP – DB
–40°C to 85°C
TSSOP – PW
(1)
ORDERABLE PART NUMBER
Tube of 70
MAX3318ECDB
Reel of 2000
MAX3318ECDBR
Tube of 70
MAX3318ECPW
Reel of 2000
MAX3318ECPWR
Tube of 70
MAX3318EIDB
Reel of 2000
MAX3318EIDBR
Tube of 70
MAX3318EIPW
Reel of 2000
MAX3318EIPWR
TOP-SIDE MARKING
MP318EC
MP318EC
MP318EI
MP318EI
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
ABC
DETAILED DESCRIPTION
Flexible control options for power management are featured when the serial port and driver inputs are inactive.
The auto-power-down plus feature functions when FORCEON is low and FORCEOFF is high. During this mode
of operation, if the device does not sense valid signal transitions on all receiver and driver inputs for
approximately 30 s, the built-in charge pump and drivers are powered down, reducing the supply current to
1 µA. By disconnecting the serial port or placing the peripheral drivers off, auto-power-down plus can be
disabled when FORCEON and FORCEOFF are high. With auto-power-down plus enabled, the device activates
automatically when a valid signal is applied to any receiver or driver input. INVALID is high (valid data) if any
receiver input voltage is greater than 2.7 V or less than –2.7 V, or has been between –0.3 V and 0.3 V for less
than 30 µs (typical number). INVALID is low (invalid data) if all receiver input voltage are between –0.3 V and
0.3 V for more than 30 µs (typical number).
2
Submit Documentation Feedback
MAX3318E
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS741 – JUNE 2006
FUNCTION TABLE
INPUT CONDITIONS
FORCEON
FORCEOFF
RECEIVER
OR DRIVER
EDGE
WITHIN 30 s
(1)
OUTPUT STATES
VALID
RS-232
LEVEL
PRESENT AT
RECEIVER
DRIVER
RECEIVER
INVALID
READY
OPERATING
MODE
Auto-Power-Down Plus Conditions
H
H
No
No
Active
Active
L
H
Normal operation,
auto-power-down
plus disabled
H
H
No
Yes
Active
Active
H
H
Normal operation,
auto-power-down
plus disabled
L
H
Yes
No
Active
Active
L
H
Normal operation,
auto-power-down
plus enabled
L
H
Yes
Yes
Active
Active
H
H
Normal operation,
auto-power-down
plus enabled
L
H
No
No
Z
Active
L
L
Power down,
auto-power-down
plus enabled
L
H
No
Yes
Z
Active
H
L
Power down,
auto-power-down
plus enabled
X
L
X
No
Z
Active
L
L
Manual power
down
X
L
X
Yes
Z
Active
H
L
Manual power
down
Auto-Power-Down Conditions
(1)
INVALID
INVALID
X
No
Z
Active
L
L
Power down,
auto power down
enabled
INVALID
INVALID
X
Yes
Active
Active
H
H
Normal operation,
auto power down
enabled
H = high level, L = low level, X = irrelevant, Z = high impedance
Submit Documentation Feedback
3
MAX3318E
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS741 – JUNE 2006
LOGIC DIAGRAM (POSITIVE LOGIC)
DIN1
DIN2
FORCEOFF
FORCEON
ROUT1
13
17
12
8
20
11
14
Auto-Power-Down Plus
15
1
16
DOUT1
DOUT2
INVALID
READY
RIN1
5 kΩ
ROUT2
10
9
5 kΩ
4
Submit Documentation Feedback
RIN2
MAX3318E
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS741 – JUNE 2006
TERMINAL FUNCTIONS
TERMINAL
NAME
DESCRIPTION
NO.
C1+
2
Positive voltage-doubler charge-pump capacitor
C1–
4
Negative voltage-doubler charge-pump capacitor
C2+
5
Positive inverting charge-pump capacitor
C2–
6
Negative inverting charge-pump capacitor
DIN
12, 13
CMOS driver inputs
DOUT
8, 17
RS-232 driver outputs
FORCEOFF
20
Force-off input, active low. Drive low to power down transmitters, receivers, and charge pump. This overrides
auto power down and FORCEON (see Function Table).
FORCEON
14
Force-on input, active high. Drive high to override auto power down, keeping transmitters and receivers on
(FORCEOFF must be high) (see Function Table).
GND
18
Ground
INVALID
11
Valid signal detector output, active low. A logic high indicates that a valid RS-232 level is present on a receiver
input.
READY
1
Ready to transmit output, active high. READY is enabled high when V– goes below –3.5 V and the device is
ready to transmit.
RIN
9, 16
RS-232 receiver inputs
ROUT
10, 15
CMOS receiver outputs
V+
3
2 × VCC generated by the charge pump
V–
7
–2 × VCC generated by the charge pump
VCC
19
2.25-V to 3-V single-supply voltage
Submit Documentation Feedback
5
MAX3318E
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS741 – JUNE 2006
Absolute Maximum Ratings (1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
VCC to GND
–0.3
6
V
V+ to GND (2)
–0.3
7
V
GND (2)
–7
0.3
V
13
V
V– to
V+ + IV-I (2)
Input voltage
Output voltage
Short-circuit duration
Continuous power dissipation (TA = 70°C)
DIN, FORCEON, FORCEOFF to GND
–0.3
6
±13.2
DOUT to GND
ROUT, INVALID, READY to GND
–0.3
DOUT to GND
V
VCC + 0.3
Continuous
16-pin SSOP (derate 7.14 mW/°C above 70°C)
571
20-pin SSOP (derate 8 mW/°C above 70°C
640
20-pin TSSOP (derate 7 mW/°C above 70°C)
559
–65
Lead temperature (soldering, 10 s)
(2)
V
±25
RIN to GND
Storage temperature range
(1)
UNIT
mW
150
°C
300
°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
V+ and V– can have maximum magnitudes of 7 V, but their absolute difference cannot exceed 13 V.
Recommended Operating Conditions
See Figure 4
MIN NOM
Supply voltage
2.5
MAX UNIT
3
V
VIH
Driver and control high-level input voltage
DIN, FORCEOFF,
FORCEON
VCC = 2.5 V to 3 V
0.7 × VCC
5.5
V
VIL
Driver and control low-level input voltage
DIN, FORCEOFF,
FORCEON
VCC = 2.5 V to 3 V
0
0.3 × VCC
V
VI
Receiver input voltage
–25
25
V
0
70
–40
85
TA
6
2.25
Operating free-air temperature
MAX3318EC
MAX3318EI
Submit Documentation Feedback
°C
MAX3318E
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS741 – JUNE 2006
Supply Current Section Electrical Characteristics
VCC = 2.25 V to 3 V, C1–C4 = 0.1 µF, TA = TMIN to TMAX (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP (1) MAX
UNIT
DC Characteristics (VCC = 2.5 V, TA = 25°C)
Auto-power-down plus supply current FORCEON = GND, FORCEOFF = VCC, All RIN and DIN idle
Auto-power-down supply current
FORCEOFF = GND
Supply current
FORCEON = FORCEOFF = VCC, No load
(1)
µA
1
10
1
10
µA
0.3
2
mA
Typical values are at VCC = 2.5 V, TA = 25°C.
ESD Protection
PARAMETER
RIN, DOUT
TEST CONDITIONS
TYP
HBM
±15
IEC 61000-4-2 Air-Gap Discharge method
±15
IEC 61000-4-2 Contact Discharge method
±8
Submit Documentation Feedback
UNIT
kV
7
MAX3318E
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS741 – JUNE 2006
Driver Section Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature,
VCC = 2.25 V to 3 V, C1–C4 = 0.1 µF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 4)
PARAMETER
TEST CONDITIONS
MIN TYP (1)
Driver input hysteresis
±0.01
Input leakage current
FORCEON, DIN, FORCEOFF
Output voltage swing
All driver outputs loaded with 3 kΩ to ground
±3.7
±4
Output resistance
VCC = 0, Driver output = ±2 V
300
10M
±25
Output short-circuit current (2)
Output leakage current
(1)
(2)
MAX
0.3
VCC = 0 or 2.25 V to 3 V, VOUT = ±12 V, Drivers disabled
UNIT
V
±1
µA
V
Ω
±60
mA
±25
µA
Typical values are at VCC = 2.5 V, TA = 25°C.
Short-circuit durations should be controlled to prevent exceeding the device absolute power dissipation ratings, and not more than one
output should be shorted at a time.
Driver Section Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature,
VCC = 2.25 V to 3 V, C1–C4 = 0.1 µF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 1)
PARAMETER
Maximum data rate
|tPHL – tPLH|
8
RL = 3 kΩ, CL = 1000 pF, One transmitter switching
MIN
TYP (1)
MAX
460
Driver skew (2)
Transition-region slew rate
(1)
(2)
TEST CONDITIONS
kbps
100
VCC = 2.5 V, TA = 25°C, RL = 3 kΩ to 7 kΩ,
Measured from 3 V to –3 V or –3 V to 3 V,
CL = 150 pF to 2500 pF
Typical values are at VCC = 2.5 V, TA = 25°C.
Pulse skew is defined as |tPLH – tPHL| of each channel of the same device.
Submit Documentation Feedback
4
UNIT
ns
30
V/µs
MAX3318E
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS741 – JUNE 2006
Receiver Section Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature,
VCC = 2.25 V to 3 V, C1–C4 = 0.1 µF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 4)
PARAMETER
MIN TYP (1)
TEST CONDITIONS
Input voltage range
–25
Input threshold low
TA = 25°C
Input threshold high
TA = 25°C
0.7 × VCC
TA = 25°C
3
Input hysteresis
Output leakage current
Output voltage low
IOUT = 0.5 mA
Output voltage high
IOUT = –0.5 mA
UNIT
25
V
0.3 × VCC
V
V
0.3
Input resistance
(1)
MAX
V
5
7
kΩ
±0.05
±10
µA
0.1 × VCC
V
0.9 × VCC
V
Typical values are at VCC = 2.5 V, TA = 25°C.
Receiver Section Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature,
VCC = 2.25 V to 3 V, C1–C4 = 0.1 µF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 4)
PARAMETER
tPHL
Receiver propagation delay
tPLH
|tPHL – tPLH|
(1)
(2)
TEST CONDITIONS
RIN to ROUT, CL = 150 pF
Receiver skew (2)
TYP (1)
0.175
0.175
50
UNIT
µs
ns
Typical values are at VCC = 2.5 V, TA = 25°C.
Pulse skew is defined as |tPLH – tPHL| of each channel of the same device.
Submit Documentation Feedback
9
MAX3318E
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS741 – JUNE 2006
Auto-Power-Down Plus Section Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature,
VCC = 2.25 V to 3 V, C1–C4 = 0.1 µF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 4)
PARAMETER
TEST CONDITIONS
MIN
MAX
Positive threshold
Receiver input threshold to INVALID high
2.7
Negative threshold
–2.7
Receiver input threshold INVALID low
–0.3
INVALID, READY voltage low
IOUT = 0.5 mA
INVALID, READY voltage high
IOUT = –0.5 mA
UNIT
V
0.3
V
0.1 × VCC
V
0.8 × VCC
V
Auto-Power-Down Plus Section Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature,
VCC = 2.25 V to 3 V, C1–C4 = 0.1 µF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 4)
PARAMETER
TEST CONDITIONS
MIN
TYP (1)
MAX
UNIT
tINVH
Receiver positive or negative threshold to INVALID high
VCC = 2.5 V
1
µs
tINVL
Receiver positive or negative threshold to INVALID low
VCC = 2.5 V
30
µs
tWU
Receiver or driver edge to driver enabled
VCC = 2.5 V
tAUTOPRDN
Receiver or driver edge to driver shutdown
VCC = 2.5 V
(1)
10
Typical values are at VCC = 2.5 V, TA = 25°C.
Submit Documentation Feedback
µs
100
15
30
60
s
MAX3318E
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS741 – JUNE 2006
PARAMETER MEASUREMENT INFORMATION
3V
Generator
(see Note B)
Input
RS-232
Output
50 Ω
RL
CL
(see Note A)
3V
FORCEOFF
TEST CIRCUIT
0V
tTHL
Output
SR(tr) +
6V
t THL or tTLH
tTLH
VOH
3V
3V
−3 V
−3 V
VOL
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns.
Figure 1. Driver Slew Rate
2.25 V
Generator
(see Note B)
RS-232
Output
50 Ω
RL
Input
1.125 V
1.125 V
0V
CL
(see Note A)
tPLH
tPHL
VOH
3V
FORCEOFF
50%
50%
Output
VOL
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns.
Figure 2. Driver Pulse Skew
3V
Input
0V
0V
−3 V
Output
Generator
(see Note B)
tPHL
50 Ω
tPLH
CL
(see Note A)
VOH
50%
Output
50%
VOL
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns.
Figure 3. Receiver Propagation Delay Times
Submit Documentation Feedback
11
MAX3318E
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS741 – JUNE 2006
PARAMETER MEASUREMENT INFORMATION
Receiver
Inputs
}
Invalid
Region
Driver
Inputs
Driver
Outputs
VCC
INVALID
Output
tINVL
tINVH
0
tWU
tWU
VCC
Ready
Output
0
V+
VCC
0
V−
VOLTAGE WAVEFORMS
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
Valid RS-232 Level, INVALID High
ROUT
Generator
(see Note B)
2.7 V
50 Ω
Indeterminate
0.3 V
0V
If Signal Remains Within This Region
For More Than 30 µs, INVALID Is Low†
−0.3 V
Auto-PowerDown Plus
Indeterminate
INVALID
−2.7 V
CL = 30 pF
(see Note A)
†
FORCEON
FORCEOFF
Valid RS-232 Level, INVALID High
DIN
DOUT
Auto power down disables drivers and reduces supply
current to 1 µA.
TEST CIRCUIT
Figure 4. INVALID Propagation Delay Times and Supply Enabling Time
12
Submit Documentation Feedback
MAX3318E
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS741 – JUNE 2006
PARAMETER MEASUREMENT INFORMATION
2.5 V
+ 0.1 mF
19
CBYPASS
2
C1
0.1 mF
C2
0.1 mF
+
4
+
5
6
VCC
C1+
V+
3
+
C1−
V−
C2+
7
C2−
13 DIN1
DOUT1 17
12 DIN2
DOUT2 8
C4
+ 0.1 mF
RS-232-Compatible
Outputs
RS-232-Compatible
Inputs
RIN1 16
15 ROUT1
C3
0.1 mF
5k
10 ROUT2
1
RIN2 9
5k
READY
To Power-Management Unit
Auto-Power- INVALID 11
Down Plus
VCC
FORCEOFF 20
14
FORCEON
GND
18
Figure 5. Typical Application Circuit
Submit Documentation Feedback
13
PACKAGE OPTION ADDENDUM
www.ti.com
18-Jul-2006
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
MAX3318ECDB
ACTIVE
SSOP
DB
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MAX3318ECDBG4
ACTIVE
SSOP
DB
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MAX3318ECDBR
ACTIVE
SSOP
DB
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MAX3318ECDBRG4
ACTIVE
SSOP
DB
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MAX3318ECPW
ACTIVE
TSSOP
PW
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MAX3318ECPWG4
ACTIVE
TSSOP
PW
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MAX3318ECPWR
ACTIVE
TSSOP
PW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MAX3318ECPWRG4
ACTIVE
TSSOP
PW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MAX3318EIDB
ACTIVE
SSOP
DB
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MAX3318EIDBG4
ACTIVE
SSOP
DB
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MAX3318EIDBR
ACTIVE
SSOP
DB
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MAX3318EIDBRG4
ACTIVE
SSOP
DB
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MAX3318EIPW
ACTIVE
TSSOP
PW
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MAX3318EIPWG4
ACTIVE
TSSOP
PW
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MAX3318EIPWR
ACTIVE
TSSOP
PW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
MAX3318EIPWRG4
ACTIVE
TSSOP
PW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
18-Jul-2006
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
12.0
16.0
Q1
MAX3318ECDBR
SSOP
DB
20
2000
330.0
16.4
8.2
7.5
2.5
MAX3318ECPWR
TSSOP
PW
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
MAX3318EIDBR
SSOP
DB
20
2000
330.0
16.4
8.2
7.5
2.5
12.0
16.0
Q1
MAX3318EIPWR
TSSOP
PW
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
MAX3318ECDBR
SSOP
DB
20
2000
346.0
346.0
33.0
MAX3318ECPWR
TSSOP
PW
20
2000
346.0
346.0
33.0
MAX3318EIDBR
SSOP
DB
20
2000
346.0
346.0
33.0
MAX3318EIPWR
TSSOP
PW
20
2000
346.0
346.0
33.0
Pack Materials-Page 2
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
DB (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
28 PINS SHOWN
0,38
0,22
0,65
28
0,15 M
15
0,25
0,09
8,20
7,40
5,60
5,00
Gage Plane
1
14
0,25
A
0°–ā8°
0,95
0,55
Seating Plane
2,00 MAX
0,10
0,05 MIN
PINS **
14
16
20
24
28
30
38
A MAX
6,50
6,50
7,50
8,50
10,50
10,50
12,90
A MIN
5,90
5,90
6,90
7,90
9,90
9,90
12,30
DIM
4040065 /E 12/01
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-150
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DLP® Products
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated
Similar pages