Omron G6W-1F High-frequency relay Datasheet

High-frequency Relay
G6W
Surface-mountable 5 GHz Band Miniature
SPDT High-frequency Relay
• Superior high-frequency characteristics, such as an
isolation of 35 dB min., insertion loss of 0.5 dB max., and
V.S.W.R. of 1.7 max. at 5 GHz (50 Ω).
• High-frequency characteristics obtained by adopting
tri-plate micro strip line design.
• Small size at 20 x 9.4 x 8.9 mm (L x W x H).
• Y-shape terminal structure and reverse contact option
simplifies wiring to PCBs.
• RoHS Compliant.
Ordering Information
Classification
SPDT
Note:
Fully sealed
Non latching
Single-coil
latching
Dual-coil
latching
Through-hole terminal
Y-shape terminal
G6W-1P
G6WU-1P
G6WK-1P
Surface-mount terminal
Y-shape terminal
G6W-1F
G6WU-1F
G6WK-1F
When ordering, add the rated coil voltage to the model number.
Example: G6W-1P DC12
Rated coil voltage
Model Number Legend:
G6W
1
2 3 4
5
1. Relay function
3. Terminal shape
5. Contact Arrangement
None: Non-latching
F:
Surface-mount terminals
None: Standard contact arrangement
U:
Single-coil latching
P:
PCB through-hole terminals
R:
K:
Dual-coil latching
2. Contact form
1:
SPDT
4. Terminal Structure
None: Y-shape terminal
(standard)
Reverse contact arrangement
(Available only for Non-Latching
versions)
■ Typical Applications
•
•
•
•
Mobile phone base station (W-CDMA, UMTS, CDMA-2000, PCS)
Wireless LAN and TV transmitters
Test and Measurement devices
Signal Generators
High-frequency Relay
G6W
327
Specifications
■ Contact Ratings
Load type
Resistive load
Contact material
Au clad Cu alloy
Rated load
10 mA at 30 VAC; 10 mA at 30 VDC
2.5 GHz, 50 Ω, 10 W (See note 2)
Rated carry current
0.5 A
Max. switching voltage
30 VDC, 30 VAC
Max. switching current
0.5 A
■ High-frequency Characteristics
Frequency
2.0 GHz
2.5 GHz
60 dB min.
5.0 GHz
Isolation
65 dB min.
35 dB min.
Insertion loss
0.2 dB max.
0.5 dB max.
V.S.W.R.
1.2 max.
1.7 max.
Max. carry power
20 W (See note 2)
Max. switching power
10 W (See note 2)
Note: 1. The above values are initial values.
2. These values are for a load with V.S.W.R. ≤1.2 at an impedance of 50 Ω.
■ Coil Ratings
Non-latching Relays (G6W-1F, G6W-1P)
Rated voltage
3 VDC
4.5 VDC
9 VDC
12 VDC
Rated current
66.7 mA
44.4 mA
22.2 mA
16.7 mA
24 VDC
8.3 mA
Coil resistance
45 Ω
101 Ω
405 Ω
720 Ω
2,880 Ω
Must operate voltage
80% of max. of rated voltage
Must release voltage
10% min. of rated voltage
Maximum voltage
150% of rated voltage
Power consumption
Approx. 200 mW
Single-coil Latching Relays (G6WU-1F, G6WU-1P)
Rated voltage
9 VDC
Rated current
22.2 mA
12 VDC
16.7 mA
Coil resistance
405 Ω
720 Ω
Must set voltage
80% max. of rated voltage
Must reset voltage
80% max of rated voltage
Maximum voltage
150% of rated voltage
Power consumption
Approx. 200 mW
Dual-coil Latching Relays (G6WK-1F, G6WK-1P)
Rated voltage
3 VDC
4.5 VDC
9 VDC
12 VDC
Rated current
120 mA
80 mA
40 mA
30 mA
15 mA
Coil resistance
25 Ω
56 Ω
225 Ω
400 Ω
1,600 Ω
Must set voltage
80% max. of rated voltage
Must reset voltage
80% max. of rated voltage
Maximum voltage
150% of rated voltage
Power consumption
Approx. 360 mW
Note: 1.
2.
3.
4.
328
24 VDC
The rated current and coil resistance are measured at a coil temperature of 23°C with a tolerance of ± 10%.
The operating characteristics are measured at a coil temperature of 23°C.
The maximum voltage is the highest voltage that can be imposed on the relay coil.
The voltage measurements for operate/release and set/reset are the values obtained for instantaneous changes in the voltage.
(Rectangular wave).
High-frequency Relay
G6W
■ Characteristics
Item
Non-latching
Single-coil latching
Dual-coil latching
G6W-1F, G6W-1P
G6WU-1F, G6WU-1P
G6WK-1F, G6WK-1P
Contact resistance (See note 2)
100 mΩ max.
Operate (set) time (See note 3)
10 ms max. (Approx. 3.5 ms) 10 ms max. (Approx. 2.5 ms)
Release (reset) time (See note 3)
10 ms max. (Approx. 2.5 ms)
Minimum set/reset signal width
-----
Insulation resistance (See note 4)
1,000 MΩ min. (at 500 VDC)
Dielectric strength
Coil and contacts
1,000 VAC, 50/60 Hz for 1 min
Coil and ground,
contacts and ground
500 VAC, 50/60 Hz for 1 min
Contact of same
polarity
500 VAC, 50/60 Hz for 1 min
Destruction
10 to 55 Hz, 1.5-mm double amplitude
Malfunction
10 to 55 Hz, 2-mm double amplitude
Destruction
1,000 m/s2
Malfunction
500 m/s2
Mechanical
1,000,000 operations min. (at 36,000 operations/hour)
Electrical
300,000 operations min. (with a rated load at 1,800 operations/hour)
100,000 operations min. (2.5GHz, 50 Ω, 10 W)
Vibration resistance
Shock resistance
Endurance
12 ms
Ambient temperature
Operating: -40°C to 70°C (with no icing or condensation)
Ambient humidity
Operating: 5% to 85%
Weight
Approx. 3 g
Note: 1.
2.
3.
4.
The above values are initial values.
The contact resistance was measured with 10 mA at 1 VDC with a fall-of-potential method.
Values in parentheses are typical values.
The insulation resistance was measured with a 500-VDC Megger Tester applied to the same parts as those used for checking the dielectric strength.
Engineering Data
Ambient Temperature vs.
Must Set or Must Reset Voltage
250
On the basis of rated voltage (%)
Maximum voltage (%)
Ambient Temperature vs.
Maximum Voltage
200
150
100
50
100
max.
avg.
max.
avg.
min.
min.
80
70
60
0
20
40
60
80
100
Ambient temperature (°C)
Note: “Maximum voltage” is the maximum
voltage that can be applied to the relay
coil.
1,000
Energized
800
600
X
1,000
Not
400 energized
Z
1,000
200
50
200
40
0
−60
400
1,000
Z'
30
20
−20
Y
Max. estimated value
90
10
0
−40
Shock Malfunction
Must set voltage
Must reset voltage
−40
−20
0
20
40
60
Shock direction
X
X'
Y
Z
Ambient temperature (°C)
800
1,000
Z'
80 100
1,000
X'
600
Y'
Unit: m/s2
Sample: G6WK-1P 4.5 VDC
Number of Relays: 10
Y'
Conditions: Shock is applied in ±X, ±Y, and
±Z directions three times each with and
without energizing the relays to check the
number of contact malfunctions.
High-frequency Relay
G6W
329
Electrical Endurance, DC Load:
Must Set and Must Reset Voltage
(See notes 1 and 2)
Electrical Endurance, AC Load:
Must Set and Must ResetVoltage
(See notes 1 and 2)
On the basis of rated voltage (%)
On the basis of rated voltage (%)
100
80
Must set voltage
max.
max.
60
min.
40
min.
Must reset voltage
Sample: G6WU-1P 9 VDC
20 Number of Relays: 5
Test conditions: 10-mA resistive load at
30-VDC with an operation rate of 50%.
Switching frequency: 1,800 operations/h
0
0.001 0.01
0.1
1
10
100
100
80
Must set voltage
min.
min.
Must reset voltage
40
Sample: G6WU-1P 9 VDC
20 Number of Relays: 5
Test conditions: 10-mA resistive load at
30-VAC with an operation rate of 50%.
Switching frequency: 1,800 operations/h
0
0.001 0.01
0.1
1
10
100
1,000
Operating frequency (×103 operations)
Electrical Endurance, AC Load:
Contact Resistance
(See notes 1 and 2)
Contact resistance (m )
Contact resistance (m )
1,000
Sample: G6WU-1P 9 VDC
NO contact
Number of Relays: 5
NC contact
500 Test conditions:
10-mA resistive load at 30-VDC
Switching frequency: 1,800 operations/h
300
100
50 Contact resistance
1
10
100
1,000
Sample: G6WU-1P 9 VDC
NO contact
Number of Relays: 5
NC contact
500 Test conditions:
10-mA resistive load at 30-VAC
Switching frequency: 1,800 operations/h
300
100
50 Contact resistance
max.
max.
min.
min.
30
0.1
1,000
Operating frequency (×103 operations)
Electrical Endurance, DC Load:
Contact Resistance
(See notes 1 and 2)
10
0.001 0.01
max.
max.
60
max.
max.
min.
min.
30
10
0.001 0.01
1,000
Operating frequency (×103 operations)
0.1
1
10
100
1,000
Operating frequency (×103 operations)
External Magnetic Interference
S
N
+20
+10
0
−10
−20
−30
−1,200
Must set voltage
Must reset voltage
−800
−400
0
400
(Average value)
800 1,200
+30
Sample: G6WK-1P 4.5 VDC
Number of Relays: 5
S
N
+20
+10
0
−10
−20
−30
−1,200
External magnetic field (A/m)
Must set voltage
Must reset voltage
−800
−400
0
400
800 1,200
External magnetic field (A/m)
(Average value)
Change rate on the basis of initial value (%)
Sample: G6WK-1P 4.5 VDC
Number of Relays: 5
Change rate on the basis of initial value (%)
Change rate on the basis of initial value (%)
(Average value)
+30
+30
Sample: G6WK-1P 4.5 VDC
Number of Relays: 5
S
N
+20
+10
0
−10
−20
−30
−1,200
Must set voltage
Must reset voltage
−800
−400
0
400
800 1,200
External magnetic field (A/m)
Note: 1. The tests were conducted at an ambient temperature of 23°C
2. The contact resistance data are periodically measured reference values and are not values from monitoring each operation.
Contact resistance values will vary according to the switching frequency and operating environment. Therefore, be sure to check
the operation under the actual operating conditions before use.
330
High-frequency Relay
G6W
V.S.W.R. / Return Loss
(See notes 1 and 2)
Insertion Loss
(See notes 1 and 2)
[Average (Initial value)]
20
40
0
Return loss (dB)
Insertion loss (dB)
Isolation (dB)
[Average (Initial value)]
[Average (Initial value)]
0
0.2
0.4
0
N.O.
N.C.
10
2.4
2.2
V.S.W.R.
Isolation
(See notes 1 and 2)
Return loss
20
2.0
30
1.8
40
1.6
60
0.6
80
50
120
60
N.O.
N.C.
0
1,000
2,000
3,000
4,000
1.0
5,000 6,000
0
1,000
2,000
3,000
4,000
0
1,000
2,000
3,000
1.0
5,000 6,000
4,000
Frequency (MHz)
Must Set and Must Reset
Bounce Time Distribution (see note 1).
Number of contacts
Sample:
G6WK-1P 4.5 VDC
Number of Relays: 20
70
5,000 6,000
Frequency (MHz)
Must Set and Must Reset
Time Distribution (see note 1).
20
1.2
N.O.
N.C.
Frequency (MHz)
Number of contacts
1.4
V.S.W.R.
0.8
100
Must set time
Must reset time
15
10
30
Sample:
G6WK-1P 4.5 VDC
Number of Relays: 20
25
Must set bounce time
Must reset bounce time
20
15
10
5
5
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
0
0.5
1.0
1.5
2.0
Time (ms)
2.5
3.0
Time (ms)
Note: 1. The tests were conducted at an ambient temperature of 23°C.
2. High-frequency characteristics depend upon the PCB to which the relay is mounted. Always check these characteristics, including endurance (life expectancy) in the actual application before use.
Dimensions
Note: All units are in millimeters unless otherwise indicated.
G6W-1F
G6WU-1F
Terminal Arrangement/
Internal Connections
(Top View)
Mounting Pads
(Top View)
Tolerance: ±0.1 mm
G6W-1F
2.54 2.54 2.54 2.54 5.08
Orientation mark
3.2
18
17
15 14 13
2.7
1.1
9.4
Through-hole
1.1 3
8.6
5.9
Three,
0.4
0.2
2
3
5
6 7
8
G6WU-1F
Orientation mark
18
Twelve, 0.6
15.24
22.2
1
2.8
20.4
9.2
10
5.08 9.4
1.8
20
20
11
−
+
5.08
11.6
Note: 1. Tolerance: ±0.3 mm unless specified.
2. The coplanarity of the terminals is 0.1 mm max.
20
15 14 13
17
0.2
1
S +
−
R −
+
2
3
High-frequency Relay
5
11
6 7
G6W
10
8
331
G6W-1P
G6WU-1P
Terminal Arrangement/
Internal Connections
(Bottom View)
Mounting Holes
(Bottom View)
Tolerance: ±0.1 mm
G6W-1P
1.6-dia.
Orientation mark
2.54 2.54 2.54 2.54 2.54 2.54 0.8-dia.
0.8-dia.
1.6-dia.
1
20
2.7
20
1.8 5.08 7.62
Twelve, 1.8-dia.
3
8.6
Through-hole
5.08
10.16
Three,
0.4
15.24
15 14
11
13
10
Orientation mark
5.08
7.6
18
G6WK-1F
8
G6WU-1P
1.6-dia.
Note: Tolerance: ±0.3 mm unless specified.
19
6 7
5.9
2
1
20
Twelve,
0.6
5
−
17
19
0.8-dia.
8.9
3
+
18
Twelve, 1-dia.
9.4
2
3
S +
−
R −
+
17
5
15 14
6 7
11
13
8
10
Terminal Arrangement/
Internal Connections
(Top View)
Mounting Pads
(Top View)
Tolerance: ±0.1 mm
G6WK-1F
2.54 2.54 2.54 2.54 5.08
Orientation mark
3.2
18
20
2.7
9.4
20
Three,
0.4
0.2
0.2
1.1 3
8.6
5.9
1
2
13
+
−
S
+
1.1
9.2
Thirteen, 0.6
15.24
22.2
15 14
5.08 9.4
1.8
Throughhole
17 16
3
−
R
11
6 7
5
10
8
2.8
20.4
5.08
11.6
Note: 1. Tolerance: ±0.3 mm unless specified.
2. The coplanarity of the terminals is 0.1 mm max.
G6WK-1P
Terminal Arrangement/
Internal Connections
(Bottom View)
Mounting Holes
(Bottom View)
Tolerance: ±0.1 mm
G6WK-1P
1.6-dia.
2.54 2.54 2.54 2.54 2.54 2.54 0.8-dia.
0.8-dia.
Orientation mark
1.6-dia.
20
20
2.7
9.4
Thirteen, 1.8-dia.
3
0.8-dia.
5.08
10.16
Three,
0.4
8.6
19
5.9
1.6-dia.
5.08
7.6
15.24
19
332
Note: Tolerance: ±0.3 mm unless specified.
High-frequency Relay
G6W
3
+
18
Through-hole
Thirteen,
0.6
2
1.8 5.08 7.62
Thirteen, 1-dia.
8.9
1
17 16
6 7
5
−
S
15 14
+
13
−
R
11
8
10
Recommended Soldering Method
■ Temperature Profile According to IRS Method
When performing reflow-soldering, check the profile on an actual device
after setting the temperature condition so that the temperatures at the
relay terminals and the upper surface of the case do not exceed the
limits specified in the following table.
The thickness of cream solder to be applied should be within a range
between 150 and 200 μm on OMRON's recommended PCB pattern.
Temperature (°C)
Correct Soldering
Incorrect Soldering
Relay
Insufficient
amount of
solder
T4
T3
Terminal
Solder
Land
PCB
T2
Excessive
amount of
solder
Visually check that the Relay is properly soldered.
T1
Bottom Ground Soldering Conditions
To solder the bottom ground, manually solder separately from the
terminals according to the following conditions.
• Soldering iron: 50 W
• Iron temperature: 380°C to 400°C
• Soldering time: 10 s max.
t1
Preheating
t2
Soldering
Time (s)
Item
Measuring
position
Terminal
Preheating
(T1 to T2, t1)
Soldering
(T3, t2)
150°C to 180°C, 230°C min.,
120 s max.
30 s max.
Upper surface --of case
---
Peak value
(T4)
Note: The above conditions are for a PCB with OMRON’s recommended
patterns and hole perforations. The conditions will depend on the
PCB being used. Therefore, it is recommended to double-check
the suitability under actual PCB conditions.
Soldering
250°C max.
Soldering temperature: Approx. 250°C (At 260°C if the DWS method is
used.)
255°C max.
Soldering time: Approx. 5 s max. (approx. 2 s for the first time and
approx. 3 s for the second time if the DWS method is used.)
Be sure to adjust the level of the molten solder so that the solder will not
overflow onto the PCB.
Precautions
■ Correct Use
Handling
Use the Relay as soon as possible after opening the moisture-proof
package. If the Relay is left for a long time after opening the moistureproof package, the appearance may suffer and seal failure may occur
after the solder mounting process. To store the Relay after opening the
moisture-proof package, place it into the original package and sealed the
package with adhesive tape.
When washing the product after soldering the Relay to a PCB, use a
water-based solvent or alcohol-based solvent, and keep the solvent temperature to less than 40°C. Do not put the Relay in a cold cleaning bath
immediately after soldering.
Dropping the Relay may cause damage to its functional capability.
Never use the Relay if it is dropped.
Protect the Relays from direct sunlight during operation, storage, and
transportation and keep the relays under normal temperature, humidity,
and pressure.
Coating
Do not use silicone coating to coat the Relay when it is mounted to
the PCB. Do not wash the PCB after the Relay is mounted using
detergent containing silicone. Otherwise, the detergent may remain
on the surface of the Relay.
Claw Securing Force During Automatic Insertion
During automatic insertion of Relays, make sure to set the securing force
of the claws to the following values so that the Relay characteristics will
be maintained.
C
A
B
Direction A: 4.90 N max.
Direction B: 9.80 N max.
Direction C: 9.80 N max.
Secure the claws to the area indicated by shading.
Do not attach them to the center area or to only part of the
Relay.
Latching Relay Mounting
Make sure that the vibration or shock that is generated from other
devices, such as relays in operation, on the same panel and imposed on
the Latching Relay does not exceed the rated value, otherwise the Latching Relay that has been set may be reset or vice versa. The Latching
Relay is reset before shipping. If excessive vibration or shock is imposed,
however, the Latching Relay may be set accidentally. Be sure to apply a
reset signal before use.
High-frequency Relay
G6W
333
■ High-frequency Characteristics Measurement Method and Substrate to be Measured
High-frequency Characteristics for G6W are measured as shown below.
G6W-1
Vector network analyzer
(Manufacture:
Agilent Technologies)
50- termination
resistances
HP8753D
Through-hole substrate
SMD-type substrate
Substrate: t-0.8 BT resin (Dielectric constant at 2 GHz: 3.37)
1.5
0.5 0.5
0.4
Substrate: t-0.8 BT resin (Dielectric constant at 2 GHz: 3.37)
0.5
1.8-dia.
4.5
Through-hole
1.8
1.4
1.5
0.4
Throughhole
20
R0.6
1.8 5.12
6
1.5
1.5
45°
45°
1.5
0.5
R2.1
0.5
0.5
Twenty seven,
0.6-dia.,
through-hole
3
3
Thirty one, 0.6-dia.,
through-hole
8.6
30
3
3
8.6
15.24
Undersurface of relay
Undersurface of relay
Convex position
Convex position
Note: To obtain high-frequency characteristics close to those specified in this datasheet, solder the convex point on the undersurface of the relay
to the ground pattern of the substrate.
Base plate for high-frequency characteristic compensation
13.6
2
Twenty four, 0.6-dia.,
through-hole
0.5
1.5
15
Note: The above compensation plate is used to measure the loss by
the relay.
The relay loss is determined by subtracting the data measured
for a compensation base plate from those for a high-frequency
characteristics measuring substrate mounted with a relay.
334
High-frequency Relay
G6W
Omron Electronic Components, LLC
Terms and Conditions of Sales
I. GENERAL
1. Definitions: The words used herein are defined as follows.
(a) Terms:
These terms and conditions
(b) Seller:
Omron Electronic Components LLC and its subsidiaries
(c) Buyer:
The buyer of Products, including any end user in section III through VI
(d) Products: Products and/or services of Seller
(e) Including: Including without limitation
2. Offer; Acceptance: These Terms are deemed part of all quotations, acknowledgments,
invoices, purchase orders and other documents, whether electronic or in writing, relating
to the sale of Products by Seller. Seller hereby objects to any Terms proposed in Buyer's
purchase order or other documents which are inconsistent with, or in addition to, these
Terms.
3. Distributor: Any distributor shall inform its customer of the contents after and including
section III of these Terms.
II. SALES
1. Prices; Payment: All prices stated are current, subject to change without notice by Seller.
Buyer agrees to pay the price in effect at the time the purchase order is accepted by
Seller. Payments for Products received are due net 30 days unless otherwise stated in
the invoice. Buyer shall have no right to set off any amounts against the amount owing in
respect of this invoice.
2. Discounts: Cash discounts, if any, will apply only on the net amount of invoices sent to
Buyer after deducting transportation charges, taxes and duties, and will be allowed only
if (a) the invoice is paid according to Seller's payment terms and (b) Buyer has no past
due amounts owing to Seller.
3. Interest: Seller, at its option, may charge Buyer 1.5% interest per month or the maximum
legal rate, whichever is less, on any balance not paid within the stated terms.
4. Orders: Seller will accept no order less than 200 U.S. dollars net billing.
5. Currencies: If the prices quoted herein are in a currency other than U.S. dollars, Buyer
shall make remittance to Seller at the then current exchange rate most favorable to
Seller; provided that if remittance is not made when due, Buyer will convert the amount
to U.S. dollars at the then current exchange rate most favorable to Seller available
during the period between the due date and the date remittance is actually made.
6. Governmental Approvals: Buyer shall be responsible for all costs involved in obtaining
any government approvals regarding the importation or sale of the Products.
7. Taxes: All taxes, duties and other governmental charges (other than general real
property and income taxes), including any interest or penalties thereon, imposed directly
or indirectly on Seller or required to be collected directly or indirectly by Seller for the
manufacture, production, sale, delivery, importation, consumption or use of the Products
sold hereunder (including customs duties and sales, excise, use, turnover and license
taxes) shall be charged to and remitted by Buyer to Seller.
8. Financial: If the financial position of Buyer at any time becomes unsatisfactory to Seller,
Seller reserves the right to stop shipments or require satisfactory security or payment in
advance. If Buyer fails to make payment or otherwise comply with these Terms or any
related agreement, Seller may (without liability and in addition to other remedies) cancel
any unshipped portion of Products sold hereunder and stop any Products in transit until
Buyer pays all amounts, including amounts payable hereunder, whether or not then due,
which are owing to it by Buyer. Buyer shall in any event remain liable for all unpaid
accounts.
9. Cancellation; Etc: Orders are not subject to rescheduling or cancellation unless Buyer
indemnifies Seller fully against all costs or expenses arising in connection therewith.
10. Force Majeure: Seller shall not be liable for any delay or failure in delivery resulting from
causes beyond its control, including earthquakes, fires, floods, strikes or other labor
disputes, shortage of labor or materials, accidents to machinery, acts of sabotage, riots,
delay in or lack of transportation or the requirements of any government authority.
11. Shipping; Delivery: Unless otherwise expressly agreed in writing by Seller:
(a) All sales and shipments of Products shall be FOB shipping point (unless otherwise
stated in writing by Seller), at which point title to and all risk of loss of the Products
shall pass from Seller to Buyer, provided that Seller shall retain a security interest in
the Products until the full purchase price is paid by Buyer;
(b) Delivery and shipping dates are estimates only; and
(c) Seller will package Products as it deems proper for protection against normal
handling and extra charges apply to special conditions.
12. Claims: Any claim by Buyer against Seller for shortage or damage to the Products
occurring before delivery to the carrier or any claim related to pricing or other charges
must be presented in detail in writing to Seller within 30 days of receipt of shipment.
III. PRECAUTIONS
1. Suitability: IT IS THE BUYER’S SOLE RESPOINSIBILITY TO ENSURE THAT ANY
OMRON PRODUCT IS FIT AND SUFFICIENT FOR USE IN A MOTORIZED VEHICLE
APPLICATION. BUYER SHALL BE SOLELY RESPONSIBLE FOR DETERMINING
APPROPRIATENESS OF THE PARTICULAR PRODUCT WITH RESPECT TO THE
BUYER’S APPLICATION INCLUDING (A) ELECTRICAL OR ELECTRONIC
COMPONENTS, (B) CIRCUITS, (C) SYSTEM ASSEMBLIES, (D) END PRODUCT, (E)
SYSTEM, (F) MATERIALS OR SUBSTANCES OR (G) OPERATING ENVIRONMENT.
Buyer acknowledges that it alone has determined that the Products will meet their
requirements of the intended use in all cases. Buyer must know and observe all
prohibitions of use applicable to the Product/s.
2. Use with Attention: The followings are some examples of applications for which
particular attention must be given. This is not intended to be an exhaustive list of all
possible use of any Product, nor to imply that any use listed may be suitable for any
Product:
(a) Outdoor use, use involving potential chemical contamination or electrical
interference.
(b) Use in consumer Products or any use in significant quantities.
(c) Energy control systems, combustion systems, railroad systems, aviation systems,
medical equipment, amusement machines, vehicles, safety equipment, and
installations subject to separate industry or government regulations.
(d) Systems, machines, and equipment that could present a risk to life or property.
3. Prohibited Use: NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING
SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE
PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE
WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
4. Motorized Vehicle Application: USE OF ANY PRODUCT/S FOR A MOTORIZED
VEHICLE APPLICATION MUST BE EXPRESSLY STATED IN THE SPECIFICATION BY
SELLER.
5. Programmable Products: Seller shall not be responsible for the Buyer's programming of
a programmable Product.
IV. WARRANTY AND LIMITATION
1. Warranty: Seller's exclusive warranty is that the Products will be free from defects in
materials and workmanship for a period of twelve months from the date of sale by Seller
(or such other period expressed in writing by Seller). SELLER MAKES NO WARRANTY
OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT ALL OTHER WARRANTIES,
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE OF THE PRODUCTS.
2. Buyer Remedy: Seller's sole obligation hereunder shall be to replace (in the form
originally shipped with Buyer responsible for labor charges for removal or replacement
thereof) the non-complying Product or, at Seller's election, to repay or credit Buyer an
amount equal to the purchase price of the Product; provided that there shall be no
liability for Seller or its affiliates unless Seller's analysis confirms that the Products were
correctly handled, stored, installed and maintained and not subject to contamination,
abuse, misuse or inappropriate modification. Return of any Products by Buyer must be
approved in writing by Seller before shipment.
3. Limitation on Liability: SELLER AND ITS AFFILIATES SHALL NOT BE LIABLE FOR
SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF
PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED
WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT,
WARRANTY, NEGLIGENCE OR STRICT LIABILITY. FURTHER, IN NO EVENT SHALL
LIABILITY OF SELLER OR ITS AFFILITATES EXCEED THE INDIVIDUAL PRICE OF
THE PRODUCT ON WHICH LIABILITY IS ASSERTED.
4. Indemnities: Buyer shall indemnify and hold harmless Seller, its affiliates and its
employees from and against all liabilities, losses, claims, costs and expenses (including
attorney's fees and expenses) related to any claim, investigation, litigation or proceeding
(whether or not Seller is a party) which arises or is alleged to arise from Buyer's acts or
omissions under these Terms or in any way with respect to the Products.
V. INFORMATION; ETC.
1. Intellectual Property: The intellectual property embodied in the Products is the exclusive
property of Seller and its affiliates and Buyer shall not attempt to duplicate it in any way
without the written permission of Seller. Buyer (at its own expense) shall indemnify and
hold harmless Seller and defend or settle any action brought against Seller to the extent
that it is based on a claim that any Product made to Buyer specifications infringed
intellectual property rights of another party.
2. Property; Confidentiality: Notwithstanding any charges to Buyer for engineering or
tooling, all engineering and tooling shall remain the exclusive property of Seller. All
information and materials supplied by Seller to Buyer relating to the Products are
confidential and proprietary, and Buyer shall limit distribution thereof to its trusted
employees and strictly prevent disclosure to any third party.
3. Performance Data: Performance data is provided as a guide in determining suitability
and does not constitute a warranty. It may represent the result of Seller's test conditions,
and the users must correlate it to actual application requirements.
4. Change In Specifications: Product specifications and descriptions may be changed at
any time based on improvements or other reasons. It is Seller’s practice to change part
numbers when published ratings or features are changed, or when significant
engineering changes are made. However, some specifications of the Product may be
changed without any notice.
5. Errors And Omissions: The information on Seller’s website or in other documentation
has been carefully checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
6. Export Controls: Buyer shall comply with all applicable laws, regulations and licenses
regarding (a) export of the Products or information provided by Seller; (b) sale of
Products to forbidden or other proscribed persons or organizations; (c) disclosure to noncitizens of regulated technology or information.
VI. MISCELLANEOUS
1. Waiver: No failure or delay by Seller in exercising any right and no course of dealing
between Buyer and Seller shall operate as a waiver of rights by Seller.
2. Assignment: Buyer may not assign its rights hereunder without Seller's written consent.
3. Law: These Terms are governed by Illinois law (without regard to conflict of laws).
Federal and state courts in Cook County, Illinois have exclusive jurisdiction for any
dispute hereunder.
4. Amendment: These Terms constitute the entire agreement between Buyer and Seller
relating to the Products, and no provision may be changed or waived unless in writing
signed by the parties.
5. Severability: If any provision hereof is rendered ineffective or invalid, such provision shall
not invalidate any other provision.
High-frequency Relay
G6W
Certain Precautions on Specifications and Use
1. Suitability for Use. Seller shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in
Buyer's application or use of the Product. At Buyer's request, Seller will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not
sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use.
Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer's application, product or system. Buyer
shall take application responsibility in all cases but the following is a nonexhaustive list of applications for which particular attention must be given:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety
equipment, and installations subject to separate industry or government
regulations.
(iii) Use in consumer products or any use in significant quantities.
(iv) Systems, machines and equipment that could present a risk to life or
property. Please know and observe all prohibitions of use applicable to this
product.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT
THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE
INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
2. Programmable Products. Seller shall not be responsible for the user's programming of a programmable product, or any consequence thereof.
3. Performance Data. Performance data given in this publication is provided as
a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Seller's test conditions, and the users must
correlate it to actual application requirements. Actual performance is subject to
Seller's Warranty and Limitations of Liability.
4. Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for
your application. Please consult with your Seller representative at any time to
confirm actual specifications of purchased Product.
5. Errors and Omissions. The information in this publication has been carefully
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors, or omissions.
6. RoHS Compliance. Where indicated, our products currently comply, to the
best of our knowledge as of the date of this publication, with the requirements
of the European Union's Directive on the Restriction of certain Hazardous
Substances ("RoHS"), although the requirements of RoHS do not take effect
until July 2006. These requirements may be subject to change. Please consult
our website for current information.
Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s website
at http://www.components.omron.com – under the “About Us” tab, in the Legal Matters section.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
OMRON ON-LINE
OMRON ELECTRONIC
COMPONENTS LLC
Global - http://www.omron.com
USA - http://www.components.omron.com
55 E. Commerce Drive, Suite B
Schaumburg, IL 60173
847-882-2288
Cat. No. X302-E-1
08/09
High-frequency Relay
G6W
Specifications subject to change without notice
Printed in USA
Similar pages