Intersil CA3262E Quad-gated, inverting power driver Datasheet

CA3262A, CA3262
Quad-Gated, Inverting Power Drivers
August 1997
Features
Description
•
•
•
•
•
•
The CA3262 and CA3262A are used to interface low-level
logic to high current loads. Each Power Driver has four
inverting switches consisting of a non-inverting logic input
stage and an inverting low-side driver output stage. All inputs
are 5V TTL/CMOS logic compatible and have a common
Enable input. Each output device has independent current
limiting (ILIM) and thermal limiting (TLIM) for protection from
over-load conditions. Steering diodes connected from each
output (in pairs) to the Clamp pins may be used in
conjunction with external zener diodes to protect the IC
against over-voltage transients that result from inductive load
switching.
Independent Over-Current Limiting On Each Output
Independent Over-Temperature Limiting On Each Output
Output Drivers Capable of Switching 700mA Load
Inputs Compatible With TTL or 5V CMOS Logic
Suitable For Resistive, Lamp or Inductive Loads
Power-Frame Package Construction For Good Heat
Dissipation
• Operating Temperature Ranges
- CA3262A . . . . . . . . . . . . . . . . . . . . . . . -40oC to 125oC
- CA3262 . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC
Applications
System Applications
•
•
•
•
•
•
•
•
•
•
Solenoids
Relays
Lamps
Steppers
Small Motors
Displays
To allow for maximum heat transfer from the chip, all ground
pins on the DIP, PLCC and SOIC packages are directly
connected to the mounting pad of the chip. Integral heat
spreading lead frames directly connect the bond pads and
ground leads to conduct heat from the chip junction to the
PC Board for good heat dissipation.
Automotive
Appliances
Industrial Controls
Robotics
The CA3262 and CA3262A can drive four incandescent
lamp loads without modulating their brilliance when the
“cold” lamps are energized. Outputs may be parallel
connected to drive high current loads. The maximum output
current of each output is determined by the over-current limiting threshold which is typically 1.2A but may be as low as
0.7A.
Ordering Information
PART NUMBER
TEMP.
RANGE (oC)
PKG.
NO.
PACKAGE
CA3262E
-40 to 85
16 Ld PDIP
E16.3
CA3262AE
-40 to 125
16 Ld PDIP
E16.3
CA3262AQ
-40 to 125
28 Ld PLCC
N28.45
CA3262AM
-40 to 125
24 Ld SOIC (W)
M24.3
Pinouts
15
IN B
OUT B
3
14
ENABLE
GND
4
13
GND
INDEX
4
3
2
1
CA3262A (SOIC)
TOP VIEW
PRELIMINARY
ENABLE
2
IN B
CLAMP
IN A
IN A
OUT A
16
NC
1
CLAMP
OUT A
CA3262A (PLCC)
TOP VIEW
OUT B
CA3262, CA3262A (PDIP)
TOP VIEW
28 27 26
25 GND
GND 5
OUT A
1
24 IN A
CLAMP
2
23 IN B
OUT B
3
22 ENABLE
NC
4
21 NC
20 GND
GND
5
12
GND
GND 6
24 GND
GND
5
OUT C
6
11
VCC
GND 7
23 GND
GND
6
19 GND
GND
7
18 GND
GND
8
17 GND
NC
9
16 NC
GND 9
21 GND
GND 10
20 GND
GND 11
19 GND
OUT C 10
15 VCC
CLAMP 11
14 IN C
OUT D 12
13 IN D
VCC
IN C
12 13 14 15 16 17 18
IN D
IN D
22 GND
GND 8
NC
9
IN C
OUT D
8
10
OUT C
OUT D
7
CLAMP
CLAMP
File Number
1
1836.6
CA3262A, CA3262
Functional Block Diagram
VCC
VCC
V+
CONSTANT
CURRENT
SOURCES
OUT D
TLIM
IN D
CLAMP
ILIM
TLIM
OUT C
IN C
REFERENCE
VOLTAGE
1.2V
INPUT
ILIM
ENABLE
OUT B
TLIM
ENABLE
TO SUBSEQUENT STAGES
IN B
CLAMP
ILIM
TLIM
FIGURE 1. CA3262A EQUIVALENT SCHEMATIC OF ONE
INPUT STAGE
OUT A
IN A
ILIM
TRUTH TABLE (Each Output)
ENABLE
IN
OUT
H
H
L
H
L
H
L
X
H
H = High, L = Low, X = Don’t Care
VCC
+5V P.S.
V+
RELAY
OUT D
IN D
TLIM
CLAMP
VBATT
ILIM
OUT C
IN C
TTL OR
CMOS
LOGIC
LEVEL
INPUTS
SOLENOID
TLIM
VBATT
ENABLE
ILIM
OUT B
IN B
HIGH CURRENT
HIGH SIDE DR
TLIM
CLAMP
MOTOR
ILIM
VBATT
OUT A
IN A
TLIM
LAMP
ILIM
FIGURE 2. QUAD INVERTING POWER DRIVER (QDR) SHOWN WITH TYPICAL APPLICATION LOADS
2
CA3262A, CA3262
Absolute Maximum Ratings
Thermal Information
Logic Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Logic Input Voltage, VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15V
Output Voltage, VCEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60V
Output Sustaining Voltage, VCE(SUS) . . . . . . . . . . . . . . . . . . . . 40V
Output Transient Current . . . . . . . . . . . . . . . . . . . . . . . . . . (Note 1)
Output Load Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Note 2)
Thermal Resistance (Typical, Note 3)
θJA (oC/W)
For PC Mount Without Added Copper Ground Area
CA3262E (PDIP) . . . . . . . . . . . . . . . . . . . . . . . . .
60
CA3262AE (PDIP) . . . . . . . . . . . . . . . . . . . . . . . .
60
CA3262AQ (PLCC) . . . . . . . . . . . . . . . . . . . . . . .
45
CA3262AM (SOIC) . . . . . . . . . . . . . . . . . . . . . . .
60
For PC Mount With 2 sq. in. of Added Copper Ground Area
CA3262E (PDIP) . . . . . . . . . . . . . . . . . . . . . . . . .
40
CA3262AE (PDIP) . . . . . . . . . . . . . . . . . . . . . . . .
40
CA3262AQ (PLCC) . . . . . . . . . . . . . . . . . . . . . . .
36
CA3262AM (SOIC) . . . . . . . . . . . . . . . . . . . . . . .
36
See Maximum Power Dissipation vs Temperature curves, Figures
6A and 6B.
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC
Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 265oC
Operating Conditions
Temperature Range
CA3262AE, CA3262AQ, CA3262AM . . . . . . . . . . -40oC to 125oC
CA3262E. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Electrical Specifications
VCC = 5.5V, TA = -40oC to 125oC for CA3262A and VCC = 5.5V, TA = -40oC to 85oC for CA3262
Unless Otherwise Specified
CA3262
PARAMETER
Output Leakage Current
SYMBOL
ICEX
TEST CONDITIONS
VCE = 60V, VENABLE = 0.8V
Output Sustaining
Voltage
VCE(SUS) Note 5
Collector Emitter
Saturation Voltage
(See Figures 4B and 5B)
VCE(SAT) VIN = 2V, VCC = 4.75V
CA3262A
MIN
TYP
MAX
MIN
TYP
MAX
UNITS
-
-
100
-
0.6
50
µA
40
-
-
40
-
-
V
IC = 100mA
-
-
0.25
-
0.05
0.15
V
IC = 200mA
-
-
-
-
-
0.2
V
IC = 300mA
-
-
-
-
-
0.25
V
IC = 400mA
-
-
0.4
-
0.2
0.3
V
IC = 500mA
-
-
-
-
-
0.4
V
IC = 600mA
-
-
0.6
-
-
0.5
V
IC = 700mA, TA = -40oC
-
-
0.6
-
-
0.5
V
Input Low Voltage
VIL
-
-
0.8
-
-
0.8
V
Input High Voltage
VIH
2
-
-
2
-
-
V
Input Low Current
IIL
VIN = 0.8V
-
-
10
-
0.75
10
µA
Input High Current
IIH
VIN = VENABLE = 5.5V,
IC = 600mA
-
-
10
-
-
10
µA
VIN = 2V, VENABLE = 5.5V,
IOUTA = 250mA, IOUTB = 250mA,
IOUTC = 250mA, IOUTD = 250mA
-
-
70
-
(Note 4)
55
mA
-
-
5
-
(Note 4)
5
mA
-
-
100
-
-
50
µA
Supply Current,
All Outputs ON,
(See Figures 4A and 5A)
ICC(ON)
Supply Current, All
Outputs OFF,
(See Figures 4A and 5A)
ICC(OFF)
VIN = 0V
Clamp Diode Leakage
Current
IR
Clamp Diode Forward
Voltage,
(See Figures 4D and 5D)
VF
Turn-On Delay,
(See Figures 4C and 5C)
Over Current Limiting
VR = 60V
IF = 1A, VIN = 0V
-
-
1.7
-
-
1.7
V
IF = 1.5A, VIN = 0V
-
-
2.1
-
-
2.1
V
-
-
8
-
-
8
µs
0.7
-
(Note 1)
0.7
-
(Note 1)
A
-
155
-
-
155
-
oC
tPHL, tPLH IOUT = 500mA
ILIM
VOUT = 2V, VIN = 5.5V,
VENABLE = 5.5V
DESIGN PARAMETERS
Over Temperature Limiting
(Junction Temperature)
TLIM
3
CA3262A, CA3262
Electrical Specifications
VCC = 5.5V, TA = -40oC to 125oC for CA3262A and VCC = 5.5V, TA = -40oC to 85oC for CA3262
Unless Otherwise Specified (Continued)
CA3262
PARAMETER
SYMBOL
TEST CONDITIONS
CA3262A
MIN
TYP
MAX
MIN
TYP
MAX
UNITS
-
-
-
3
-
pF
-
-
4.4
-
pF
Input Capacitance, Input
CIN
-
Enable Capacitance
CEN
-
NOTES:
1. The CA3262 and CA3262A have on-chip limiting for transient peak currents. Under short-circuit conditions with voltage applied to the collector
of the output transistor and with the output transistor turned ON, the current will increase to 1.2A, typical. Over-Current Limiting protects a short
circuit condition for a normal operating range of output supply voltage. During a short circuit condition, the output driver will shortly thereafter
(approx. 5ms) go into Over-Temperature Limiting. While Over-Current Limiting may range to peak currents greater than 2A, each output will
typically withstand a direct short circuit up to supply voltage levels of 16V. Excessive dissipation before thermal limiting occurs may cause damage to the chip for supply voltages greater than 18V. The CA3262 and CA3262A are rated to withstand peak current, cold turn-on conditions of
#168 or #194 lamp loads.
2. The total DC current for the CA3262 and CA3262A with all 4 outputs ON should not exceed the total of (4 x 0.7A + Max. ICC) ~ 2.85A. This level
of current will significantly increase the chip temperature due to increased dissipation and may cause thermal shutdown in high ambient temperature conditions (See Absolute Maximum Ratings for Dissipation). Any one output may be allowed to exceed 0.7A but may be subject to
Over-Current Limiting above the ILIM min. limit of 0.7A. As a practical limit, no single output should be loaded to more than 1A (Max).
3. Normal applications require a surface mount of the 28 lead PLCC and 24 lead SOIC packages on a PC Board. The PLCC, SOIC and PDIP
packages have power lead frame construction through the ground pins to conduct heat from the frame to the PC Board ground area. Thermal
resistance, θJA, is given for a surface mount of the 28 lead PLCC and the 24 lead SOIC packages on a 1 oz. copper PC board with minimal
ground area and with 2 square inches of ground area.
4. ICC varies with temperature. Typically, ICC(ON) is 18mA at 125oC and 41mA at -40oC. Typically, ICC(OFF) is 2.2mA at 125oC and 1.2mA at
-40oC.
5. Tested with a switched-off 500mA Load of 120mH (with 24Ω series resistance), VBATT = 12V and the outputs (VCE) clamped to +40V maximum
with an external zener diode.
Applications
Typical circuit configurations for applying the CA3262 and
CA3262A are shown in the application circuit of Figure 2. To
their rated capabilities, both circuits can be used to drive inductive, resistive and lamp loads. The CA3262A has a lower VSAT
than the CA3262 and is rated for 125oC ambient temperature
applications. The CA3262 data sheet rating is 85oC. Otherwise,
the protection features described apply to both the CA3262 and
CA3262A.
The maximum voltage for full load current switching is the
output sustaining voltage, VCE(SUS) which should not exceed
40V. To provide a means of over-voltage protection, on-chip
steering diodes are connected from each output to one of two
CLAMP pins. Over-voltage pulses may be generated from
inductive load switching and must be clamped or limited to a
peak voltage less than VCE(SUS) . To limit an inductive voltage
pulse, a zener diode should be connected to the appropriate
CLAMP pin. When the voltage pulse exceeds the zener threshold, the excess energy is dumped to ground via the on-chip
steering diode and the external zener diode.
The on-chip diodes may be used in a free-wheeling mode by
connecting the CLAMP pins to an external clamp supply
voltage. Zener diode clamp protection is preferred over the
power supply clamp option, primarily because the power
supplies may be subject to large transient changes; including
turn-ON and turn-OFF conditions where non-tracking conditions
between supplies could allow forward conduction through the
steering diodes. For all transient conditions of either method, the
clamp voltage should greater than the maximum supply voltage
of the switching outputs and less than VCE(SUS) .
Note that the rate of change of the output current during load
switching is fast. Therefore, even small values of inductance,
including the inductance of a few meters of hook-up wire to
the load circuit, can generate voltage spikes of considerable
amplitude at the output terminals and may require clamping
to protect the device ratings.
Current-limiting is provided as protection for shorted or overloaded output conditions. Voltage is sampled across a small
metal resistor in the emitter of each output stage. When the voltage exceeds a preset comparator level, drive is reduced to the
output. Current limiting is sustained unless thermal conditions
exceed the preset thermal shutdown temperature of 155oC.
If an output is shorted, the remaining three outputs will
continue to function normally unless the continued heat
spreading is sufficient to raise the junction temperature at any
other output to a level greater than 155oC. High ambient temperature conditions may allow this to happen. The degree of
interaction is minimized at chip layout design by separating
the output devices, each to a separate corner of the chip.
As noted, the thermal resistance values of the PDIP, PLCC
and SOIC packages are improved by direct connection of
the leads to the chip mounting pad. For a normal PC Board
application, the thermal resistance coefficient for each package can be significantly lowered by increasing ground copper area on the PC board next to the ground pins of the IC.
4
CA3262A, CA3262
IB
TEMP.
SENSE
CURRENT
AMPLIFIER
BANDGAP
VOLT. REF.
CURRENT
SENSE
FIGURE 3. EACH OUTPUT POWER DRIVER IS A COMPOSITE CIRCUIT WITH OVER-TEMPERATURE SENSE FOR THERMAL
LIMITING AND OVER-CURRENT SENSE TO PROVIDE CURRENT LIMITING
Typical Performance Curves
80
SUPPLY VOLTAGE (VCC) = 4.75V
0.7
60
0.6
COLLECTOR-TO-EMITTER
SATURATION VOLTAGE (V)
SUPPLY CURRENT (mA)
SUPPLY VOLTAGE (VCC) = 5.5V
70
50
VIN = 2V, IOUT = 250mA (EACH)
40
30
20
THERMAL SHUTDOWN
0.5
IC = 700mA
0.4
0.3
0.2
0.1
10
VIN = 0V, IOUT = 0mA
0
-40
-20
0
20
40
60
80
100 120
AMBIENT TEMPERATURE (oC)
-40
140
FIGURE 4A. TYPICAL SUPPLY CURRENT (PIN 11)
CHARACTERISTICS
-20
0
20
40
60
80
100 120 140
AMBIENT TEMPERATURE (oC)
FIGURE 4B. TYPICAL COLLECTOR-TO-EMITTER SATURATION
VOLTAGE CHARACTERISTICS IN QUAD-GATED
INVERTING POWER DRIVER OUTPUT
4
4
CLAMP DIODE FORWARD VOLTAGE (V)
PROPAGATION DELAY TIME (µs)
IC = 600mA
3
tPHL
VIN
2
9, 10, 15, 16
(16) (17) (27) (28)
VOUT
1, 3, 6, 8
(2) (4) (12) (14)
1
50%
50%
tPLH
tPHL
(ON)
(OFF)
50%
50%
tPLH
0
3
2
IF = 1.5A
IF = 1A
1
0
-40
-20
0
20
40
60
80
100 120 140
AMBIENT TEMPERATURE (oC)
-40
FIGURE 4C. TYPICAL PROPAGATION DELAY TIME CHARACTERISTICS
-20
0
20
40
60
80
100 120
AMBIENT TEMPERATURE (oC)
140
FIGURE 4D. TYPICAL CLAMP-DIODE FORWARD VOLTAGE
CHARACTERISTICS
FIGURE 4. TYPICAL CHARACTERISTICS OF THE CA3262E
5
CA3262A, CA3262
Typical Performance Curves
(Continued)
80
SUPPLY VOLTAGE (VCC) = 5.5V
0.7
COLLECTOR-TO-EMITTER
SATURATION VOLTAGE (V)
SUPPLY CURRENT (mA)
70
60
50
VIN HIGH
IOUT = 500mA (EACH)
40
30
20
VIN LOW
IOUT = 0mA
10
SUPPLY VOLTAGE (VCC) = 4.75
IOUT = 600mA
0.6
0.5
0.4
0.3
0.2
0.1
0
-40
-20
0
20
40
60
80
100
120
-40
140
-20
0
FIGURE 5A. TYPICAL SUPPLY CURRENT (PIN 11)
CHARACTERISTICS
40
60
80
100 120 140
FIGURE 5B. TYPICAL COLLECTOR-TO-EMITTER SATURATION
VOLTAGE CHARACTERISTICS IN QUAD-GATED
INVERTING POWER DRIVER OUTPUTS
4
CLAMP DIODE FORWARD VOLTAGE (V)
4
PROPAGATION DELAY TIME (µs)
20
AMBIENT TEMPERATURE (oC)
AMBIENT TEMPERATURE (oC)
tPHL
3
2
tPLH
9, 10, 15, 16
(16) (17) (27) (28)
1
VIN
50%
tPLH
tPHL
1, 3, 6, 8
VOUT
(ON)
(2) (4) (12) (14)
(OFF)
50%
0
3
IF = 1.5A
2
IF = 1A
1
0
-40
-20
0
20
40
60
80
100
120
-40
140
AMBIENT TEMPERATURE (oC)
-20
0
20
40
60
80
100
120
140
AMBIENT TEMPERATURE (oC)
FIGURE 5C. TYPICAL PROPAGATION DELAY TIME
CHARACTERISTICS
FIGURE 5D. TYPICAL CLAMP-DIODE FORWARD VOLTAGE
CHARACTERISTICS
FIGURE 5. TYPICAL CHARACTERISTICS OF THE CA3262AE AND CA3262AQ
2
1
1
0.5
3 2 1
1.5
PACKAGE DISSIPATION (W)
PACKAGE DISSIPATION (W)
1.5
PACKAGE DERATING WITHOUT HEAT SINK
1 - CA3262AQ (PLCC)
2 - CA3262AE (PDIP), CA3262AM (SOIC)
1
PACKAGE DERATING WITH 2 SQ INCHES OF
COPPPER PC BOARD HEAT SINK AREA
0.5
1 - CA3262AQ (PLCC)
2 - CA3262AM (SOIC)
3 - CA3262AE (PDIP)
0
0
-50
0
50
100
150
-50
AMBIENT TEMPERATURE (oC)
0
50
100
150
AMBIENT TEMPERATURE (oC)
FIGURE 6A. DISSIPATION RATING CHART FOR PLCC, PDIP
AND SOIC PACKAGES WITHOUT ADDITIONAL
HEAT SINKS
FIGURE 6B. DISSIPATION RATING CHART FOR PLCC, PDIP
AND SOIC PACKAGES WITH 2 SQ. IN. OF
COPPER PC BOARD HEAT SINKING
6
CA3262A, CA3262
Dual-In-Line Plastic Packages (PDIP)
E16.3 (JEDEC MS-001-BB ISSUE D)
N
16 LEAD DUAL-IN-LINE PLASTIC PACKAGE
E1
INDEX
AREA
1 2 3
INCHES
N/2
SYMBOL
-B-
A2
-C-
SEATING
PLANE
e
B1
D1
B
0.010 (0.25) M
A1
eC
C A B S
MAX
NOTES
-
0.210
-
5.33
4
0.015
-
0.39
-
4
A2
0.115
0.195
2.93
4.95
-
B
0.014
0.022
0.356
0.558
-
C
L
B1
0.045
0.070
1.15
1.77
8, 10
eA
C
0.008
0.014
0.204
0.355
-
D
0.735
0.775
18.66
D1
0.005
-
0.13
A
L
D1
MIN
A
E
D
MAX
A1
-ABASE
PLANE
MILLIMETERS
MIN
C
eB
NOTES:
1. Controlling Dimensions: INCH. In case of conflict between
English and Metric dimensions, the inch dimensions control.
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Symbols are defined in the “MO Series Symbol List” in Section
2.2 of Publication No. 95.
-
5
5
E
0.300
0.325
7.62
8.25
6
E1
0.240
0.280
6.10
7.11
5
e
0.100 BSC
2.54 BSC
-
eA
0.300 BSC
7.62 BSC
6
eB
-
0.430
-
10.92
7
L
0.115
0.150
2.93
3.81
4
N
4. Dimensions A, A1 and L are measured with the package seated
in JEDEC seating plane gauge GS-3.
19.68
16
16
9
Rev. 0 12/93
5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch
(0.25mm).
6. E and eA are measured with the leads constrained to be perpendicular to datum -C- .
7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater.
8. B1 maximum dimensions do not include dambar protrusions.
Dambar protrusions shall not exceed 0.010 inch (0.25mm).
9. N is the maximum number of terminal positions.
10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3,
E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch
(0.76 - 1.14mm).
7
CA3262A, CA3262
Plastic Leaded Chip Carrier Packages (PLCC)
0.042 (1.07)
0.048 (1.22)
0.042 (1.07)
0.056 (1.42)
PIN (1) IDENTIFIER
0.004 (0.10)
N28.45 (JEDEC MS-018AB ISSUE A)
C
28 LEAD PLASTIC LEADED CHIP CARRIER PACKAGE
0.025 (0.64)
R
0.045 (1.14)
0.050 (1.27) TP
C
L
INCHES
D2/E2
E1 E
C
L
D2/E2
VIEW “A”
D1
D
0.020 (0.51) MAX
3 PLCS
0.020 (0.51)
MIN
A1
A
0.045 (1.14)
MIN
MIN
MAX
MIN
MAX
NOTES
A
0.165
0.180
4.20
4.57
-
A1
0.090
0.120
2.29
3.04
-
D
0.485
0.495
12.32
12.57
-
D1
0.450
0.456
11.43
11.58
3
D2
0.191
0.219
4.86
5.56
4, 5
E
0.485
0.495
12.32
12.57
-
E1
0.450
0.456
11.43
11.58
3
E2
0.191
0.219
4.86
5.56
4, 5
N
28
28
6
Rev. 1 3/95
-C- SEATING
PLANE
0.026 (0.66)
0.032 (0.81)
MILLIMETERS
SYMBOL
0.013 (0.33)
0.021 (0.53)
0.025 (0.64)
MIN
VIEW “A” TYP.
NOTES:
1. Controlling dimension: INCH. Converted millimeter dimensions
are not necessarily exact.
2. Dimensions and tolerancing per ANSI Y14.5M-1982.
3. Dimensions D1 and E1 do not include mold protrusions. Allowable mold protrusion is 0.010 inch (0.25mm) per side.
4. To be measured at seating plane -C- contact point.
5. Centerline to be determined where center leads exit plastic body.
6. “N” is the number of terminal positions.
8
CA3262A, CA3262
Small Outline Plastic Packages (SOIC)
M24.3 (JEDEC MS-013-AD ISSUE C)
24 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE
N
INDEX
AREA
H
0.25(0.010) M
B M
INCHES
E
SYMBOL
-B1
2
3
L
SEATING PLANE
-A-
h x 45o
A
D
-C-
e
A1
B
0.25(0.010) M
C
0.10(0.004)
C A M
B S
MIN
MAX
NOTES
A
0.0926
0.1043
2.35
2.65
-
0.0040
0.0118
0.10
0.30
-
B
0.013
0.020
0.33
0.51
9
C
0.0091
0.0125
0.23
0.32
-
D
0.5985
0.6141
15.20
15.60
3
E
0.2914
0.2992
7.40
7.60
4
0.05 BSC
1.27 BSC
-
H
0.394
0.419
10.00
10.65
-
h
0.010
0.029
0.25
0.75
5
L
0.016
0.050
0.40
1.27
6
8o
0o
N
α
NOTES:
MILLIMETERS
MAX
A1
e
α
MIN
24
0o
24
7
8o
Rev. 0 12/93
1. Symbols are defined in the “MO Series Symbol List” in Section
2.2 of Publication Number 95.
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate
burrs. Mold flash, protrusion and gate burrs shall not exceed
0.15mm (0.006 inch) per side.
4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010
inch) per side.
5. The chamfer on the body is optional. If it is not present, a visual
index feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater
above the seating plane, shall not exceed a maximum value of
0.61mm (0.024 inch)
10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact.
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate
and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which
may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
9
Similar pages