MIC MZ1.0PB82V-4.6 Surface mount galss passivated zener diode Datasheet

SURFACE MOUNT GALSS PASSIVATED ZENER DIODE
Zener Voltage
MZ1.5PB11V-34.1 THRU MZ1.5PB200V-1.9
11 to 200 Volts
Steady state Power
1.5 Watts
FEATURES
•
•
•
•
•
•
•
•
DO-214AA(SMB)
For surface mounted applications in order to
Optimize board space
Low profile package
Built-in strain relief
Glass passivated junction
Low inductance
Typical IR less than 1μA above 11V
High temperature soldering:
260℃/10 seconds at terminals
Plastic package has Underwriters
Laboratory Flammability Classification 94V-O
MECHANICAL DATA
•
•
•
•
•
Dimensions in inches and (millimeters)
Cass: JEDEC DO-214AA,molded plastic over passivated
junction
Terminals: Solder plated, solderable per MIL-STD-750,
Method 2026
Polarity: Color band denotes positive end (cathode)
Standard Packaging: 12mm tape (EIA-481)
Weight: 0.003 ounces, 0.93 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
•
Ratings at 25℃ ambient temperature unless otherwise specified
Symbols
DC Power Dissipation @ TL=75℃, Measure at Zero Lead Length
(Note 1 Fig.1) Derate above 75℃
Peak forward Surge Current 8.3ms single half sine/square wave
Superimposed on rated load (JEDEC Method) (Notes 1.2)
Operating junction and Storage Temperature Range
PD
Value
Unit
IFSM
1.5
15
10
Watts
mw/℃
Amps
TJ, TSTG
-55to~+150
℃
Notes :
1. Mounted on 5.0mm2(.013mm thick) land areas
2. Measured on 8.3ms, single half sine-wave or equivalent square wave, duty cycle=4 pulses per minute maximum.
E-mail: [email protected]
Web Site: www.cnmic.com
SURFACE MOUNT GALSS PASSIVATED ZENER DIODE
Zener Voltage
MZ1.5PB11V-34.1 THRU MZ1.5PB200V-1.9
Type
MZ1.0PB11V-34.1
MZ1.0PB12V-31.2
MZ1.0PB13V-28.8
MZ1.0PB15V-25
MZ1.0PB16V-23.4
MZ1.0PB18V-20.8
MZ1.0PB20V-18.7
MZ1.0PB22V-17
MZ1.0PB24V-15.6
MZ1.0PB27V-13.9
MZ1.0PB30V-12.5
MZ1.0PB33V-11.4
MZ1.0PB36V-10.4
MZ1.0PB39V-9.6
MZ1.0PB43V-8.7
MZ1.0PB47V-8.0
MZ1.0PB51V-7.3
MZ1.0PB56V-6.7
MZ1.0PB62V-6.0
MZ1.0PB68V-5.5
MZ1.0PB75V-5.0
MZ1.0PB82V-4.6
MZ1.0PB91V-4.1
MZ1.0PB100V-3.7
MZ1.0PB110V-3.4
MZ1.0PB120V-3.1
MZ1.0PB130V-2.9
MZ1.0PB150V-2.5
MZ1.0PB160V-2.3
MZ1.0PB180V-2.1
MZ1.0PB200V-1.9
Device
Marking
Code
11V-34.1
12V-31.2
13V-28.8
15V-25
16V-23.4
18V-20.8
20V-18.7
22V-17
24V-15.6
27V-13.9
30V-12.5
33V-11.4
36V-10.4
39V-9.6
43V-8.7
47V-8.0
51V-7.3
56V-6.7
62V-6.0
68V-5.5
75V-5.0
82V-4.6
91V-4.1
100V-3.7
110V-3.4
120V-3.1
130V-2.9
150V-2.5
160V2.3
180V-2.1
200V-1.9
Nominal
Zener
Voltage
Vz@IZT
Volts
(Note 1)
11
12
13
15
16
18
20
22
24
27
30
33
36
39
43
47
51
56
62
68
75
82
91
100
110
120
130
150
160
180
200
Test
Current
IZT
mA
34.1
31.2
28.8
25
23.4
20.8
18.7
17
15.6
13.9
12.5
11.4
10.4
9.6
8.7
8
7.3
6.7
6
5.5
5
4.6
4.1
3.7
3.4
3.1
2.9
2.5
2.3
2.1
1.9
Steady state Power
Max Zener Impedance
(Note 2)
ZZT@IZT
Ohms
5.5
6.5
7
9
10
12
14
17.5
19
23
26
33
38
45
53
67
70
86
100
120
140
160
200
250
300
380
450
600
700
900
1200
11 to 200 Volts
ZZk
ZZk
Max Reverse
Leakage Current
IR
@
Ohms
550
550
550
600
600
650
650
650
700
700
750
800
850
900
950
1000
1100
1300
1500
1700
2000
2500
3000
3100
4000
4500
5000
6000
6500
7000
8000
1.5 Watts
VR
@
mA
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
μA
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Notes:TOLERANCE AND VOLTAGE DESIGNATION Tolerance designation-The type numbers listed indicate a tolerance of ±5%
E-mail: [email protected]
Web Site: www.cnmic.com
Volts
8.4
9.1
9.9
11.4
12.2
13.7
15.2
16.7
18.2
20.6
22.8
25.1
27.4
29.7
32.7
35.8
38.8
42.6
47.1
51.7
56
62.2
69.2
76
83.6
91.2
98.8
114
121.6
136.8
152
Maximum
DC Zener
Current
IZM
mAdc
136
125
115
100
93
83
75
68
62
55
50
45
41
38
34
31
29
26
24
22
20
18
16
15
13
12
11
10
9
8
7
SURFACE MOUNT GALSS PASSIVATED ZENER DIODE
Zener Voltage
MZ1.5PB11V-34.1 THRU MZ1.5PB200V-1.9
11 to 200 Volts
Steady state Power
1.5 Watts
RATING AND CHARACTERISTIC CURVES MZ1.5PB11V-34.1 THRU MZ1.5PB200V-1.9
FIG.1- STEADY STATE POWER DERATING
FIG.2- ZENER VOLTAGE-TO 12 VOLTS
θVZ,TEMPERATURE COEFICIENT
(mV/ ℃)
PD, MAXIMUM POWER DISSIPATION
(WATTS)
2.5
2
1.5
1
0.5
0
0
20
40
60
80
100
120
140
150
10
8
Vz@IZT
6
4
2
0
-2
-4
180
2
4
TL, LEAD TEMPERATURE(℃)
FIG.3- ZENER VOLTAGE-14 TO 200 VOLTS
8
10
12
FIG.4- EFFECT OF ZENER CURRENT
200
Zz, DYNMIC IMPEDANCE ( OHMS)
1K
Vz@IZT
100
70
50
30
20
10
10
20
30
50
70
100
200
TJ =25℃
500
Iz(ms)=0.1 Iz(dc)
200
Vz=150V
100
91V
50
62V
20
10
5
22V
2
12V
1
0.5
1
2
5
FIG.5- EFFECT OF ZENER VOLTAGE
200
IZ(dc)=1mA
100
70
50
0.0
20
10mA
10
7
5
3
2
20mA
5
7
10
20
50
100
IZ, ZENER TEST CURRENT (mA)
VZ, ZENER VOLTAGE (VOLTS)
Zz, DYNMIC IMPEDANCE ( OHMS)
θVZ,TEMPERATURE COEFICIENT
(mV/℃)
6
VZ, ZENER VOLTAGE ( VOLTS)
10
IZ(rms)=0.1 IZ(dc)
20
30
50
70
100
VZ, ZENER VOLTAGE (VOLTS)
E-mail: [email protected]
Web Site: www.cnmic.com
200
6.8V
500
SURFACE MOUNT GALSS PASSIVATED ZENER DIODE
Zener Voltage
MZ1.5PB11V-34.1 THRU MZ1.5PB200V-1.9
11 to 200 Volts
Steady state Power
1.5 Watts
RATING AND CHARACTERISTIC CURVES MZ1.5PB11V-34.1 THRU MZ1.5PB200V-1.9
FIG.7- Vz=12 thru 82 Volts
100
1K
RECTANGULAR
NONREPETITIVE
WAVEFORM
TJ=25℃ PRIOR
TO INTIAL PULSE
500
300
200
50
Iz, ZENER CURRENT(mA)
Ppk, PEAKSURGE POW ER(WATTS)
FIG.6- Maximum Surge Power
100
50
30
20
10
0.1
0.2 0.3 0.5
1
2
3
5
10
20 30
50
PW, PULSE WIDTH (ms)
NOTE 6. ZENER VOLTAGE (Vz) MEASUREMENT
Nominal zener voltage is measured with the device
function in thermal equilibrium with ambient
temperature at 25 ℃
E-mail: [email protected]
100
30
20
10
5
3
2
1
0.5
0.3
0.2
0.1
0
10
20
30
40
50
60
70
80
90
Vz,ZENER VOLTAGE(VOLTS)
NOTE 7. ZENER IMPEDANCE (Zz)DERIVATION
Zzt anc Zzk are measured by dividing the ac voltage
drop across the device by the accurrent applied.
The specified limits are for Iz (ac )=0.1 lz, (dc )with
the ac freqency = 60Hz
Web Site: www.cnmic.com
100
Similar pages