Diodes AP1509 150khz, 2a pwm buck dc/dc converter Datasheet

AP1509
150KHz, 2A PWM BUCK DC/DC CONVERTER
Description
Pin Assignments
The AP1509 series are monolithic IC designed for a step-
(Top View)
down DC/DC converter, and own the ability of driving a
2A load without additional transistor. It saves board space.
The external shutdown function can be controlled by logic
level and then come into standby mode. The internal
compensation makes feedback control having good line and
load regulation without external design. Regarding protected
VIN
1
Output
2
8
GND
7
GND
AP1509
function, thermal shutdown is to prevent over temperature
operating from damage, and current limit is against over
current operating of the output switch. If current limit function
occurs and VFB is down below 0.5V, the switching frequency
FB
3
6
GND
SD
4
5
GND
will be reduced. The AP1509 series operates at a switching
frequency
of
150KHz
thus
allow smaller
sized
SOP-8L
filter
components than what would be needed with lower frequency
switching regulators. Other features include a guaranteed
+4% tolerance on output voltage under specified input voltage
and output load conditions, and +15% on the oscillator
frequency. The output version included fixed 3.3V, 5V, 12V,
and an adjustable type. The chips are available in a standard
8-lead SOP-8 package.
Features
•
Applications
Output Voltage: 3.3V, 5V, 12V and Adjustable Output
Version
•
Adjustable Version Output Voltage Range, 1.23V to
•
•
•
Simple High-Efficiency Step-Down Regulator
On-Card Switching Regulators
Positive to Negative Converter
18V+4%
•
150KHz +15% Fixed Switching Frequency
•
Voltage Mode Non-Synchronous PWM Control
•
Thermal-Shutdown and Current-Limit Protection
•
ON/OFF Shutdown Control Input
•
Operating Voltage can be up to 22V
•
Output Load Current: 2A
•
SOP-8L Packages
•
Low Power Standby Mode
•
Built-in Switching Transistor On Chip
•
SOP-8L: Available in “Green” Molding Compound
•
Lead Free Finish/ RoHS Compliant (Note 1)
(No Br, Sb)
Notes:
1. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at
http://www.diodes.com/products/lead_free.html.
AP1509
Document number: DS31016 Rev. 4 - 2
1 of 13
www.diodes.com
June 2010
© Diodes Incorporated
AP1509
150KHz, 2A PWM BUCK DC/DC CONVERTER
Typical Application Circuit
(1) Fixed Type Circuit
FB
12V
DC Input
3
AP150933
1
VIN
4
SD
CIN
Capacitor
5
6
7
L1
47uH
Output
3.3V/2A
Output Load
2
Inductor
8
GND GND GND GND
(2) Adjustable Type Circuit
R2 1K
D1
Schottky Diode
Co
Capacitor
R1 1K
FB
12V
DC Input
L1
39uH
3
VIN
CIN
Capacitor
1
AP1509
2
4
5
8
SD
6
7
Output
2.5V/2A
Output Load
Inductor
D1
Schottky
Diode
GND GND GND GND
VOUT = VFB × (1 +
R1
Co
Capacitor
)
R2
VFB = 1.23V
R2 = 1K ~ 3K
(3) Delay Start Circuit
R2 1K
R1 1K
FB
12V
DC Input
VIN
CDELAY
0.1uF
1
AP1509
2
4
5
8
SD
CIN
Capacitor
L1
39uH
3
RDELAY
10K
AP1509
Document number: DS31016 Rev. 4 - 2
6
7
Output
GND GND GND GND
2.5V/2A
Output Load
Inductor
D1
Schottky
Diode
2 of 13
www.diodes.com
Co
Capacitor
June 2010
© Diodes Incorporated
AP1509
150KHz, 2A PWM BUCK DC/DC CONVERTER
Pin Descriptions
Pin Name
VIN
Output
GND
Description
Operating voltage input
Switching output
Ground
FB
Output voltage feedback control
SD
ON/OFF Shutdown
Functional Block Diagram
SD
VIN
200mV
Current
Source
bias
1.235V
Reference
2.5V
Regulator
220mV
Start
up
+
Comp
_
_
Comp
+
Frequecy
compensation
_
FB
+
Amp
_
Predriver
Comp
+
2A
Switch
Output
150kH
z
OSC.
AP1509
Document number: DS31016 Rev. 4 - 2
3 of 13
www.diodes.com
Thermal
Shutdown
GND
June 2010
© Diodes Incorporated
AP1509
150KHz, 2A PWM BUCK DC/DC CONVERTER
Absolute Maximum Ratings
Symbol
Parameter
Rating
Unit
KV
ESD HBM
Human Body Model ESD Protection
ESD MM
Machine Model ESD Protection
2
200
VIN
Supply Voltage
+24
V
VSD
ON/OFF Pin Input Voltage
-0.3 to +18
V
VFB
Feedback Pin Voltage
-0.3 to +18
V
VOUT
Output Voltage to Ground
-1
V
PD
TST
TJ
Power Dissipation
V
Internally Limited
Storage Temperature
Operating Junction Temperature
W
-65 to +150
o
-40 to +125
o
C
C
Recommended Operating Conditions
Symbol
IOUT
VOP
TA
Parameter
Output Current
Operating Voltage
Operating Ambient Temperature
AP1509
Document number: DS31016 Rev. 4 - 2
4 of 13
www.diodes.com
Min
0
4.5
-20
Max
2
22
85
Unit
A
V
o
C
June 2010
© Diodes Incorporated
AP1509
150KHz, 2A PWM BUCK DC/DC CONVERTER
Electrical Characteristics
Unless otherwise specified, VIN = 12V for 3.3V, 5V, adjustable version and VIN = 18V for the 12V version. ILOAD = 0.5A
Specifications with boldface type are for full operating temperature range, the other type are for TJ = 25ºC.
Symbol
IFB
Parameter
Feedback Bias Current
FOSC
Oscillator Frequency
FSCP
Oscillator Frequency of
Short Circuit Protect
VSAT
Saturation Voltage
DC
Max. Duty Cycle (ON)
Min. Duty Cycle (OFF)
ICL
Current Limit
IL
IQ
ISTBY
VIL
VIH
IH
IL
θJA
θJC
Output
Leakage
Output = -1 Current
Quiescent Current
Standby Quiescent
Current
Output = 0
ON/OFF Pin Logic Input
Threshold Voltage
Conditions
VFB = 1.3V
(Adjustable version only)
When current limit occurred
and VFB < 0.5V, Ta = 25 oC
IOUT = 2A
No outside circuit
VFB = 0V force driver on
VFB = 0V force driver on
VFB = 12V force driver off
Peak current
No outside circuit
VFB = 0V force driver on
No outside circuit
VFB = 12V force driver off
VIN = 22V
VFB = 12V force driver off
ON/OFF pin = 5V
VIN = 22V
Low (regulator ON)
High (regulator OFF)
ON/OFF Pin Logic Input
VLOGIC = 2.5V (OFF)
Current
ON/OFF Pin Input Current VLOGIC = 0.5V (ON)
Junction to
Thermal Resistance
SOP-8L
case
Thermal Resistance
Junction to
SOP-8L
with a copper area of
ambient
2
approximately 3 in
AP1509
Document number: DS31016 Rev. 4 - 2
5 of 13
www.diodes.com
Min
Typ.
-10
127
110
150
10
30
Max
-50
-100
173
173
Unit
50
KHz
nA
KHz
1.4
1.25
V
1.5
100
0
%
3
A
-200
-5
5
70
2.0
1.3
uA
mA
mA
10
150
200
0.6
uA
V
-0.01
-0.1
uA
-1
15
o
70
o
C/W
C/W
June 2010
© Diodes Incorporated
AP1509
150KHz, 2A PWM BUCK DC/DC CONVERTER
Electrical Characteristics (Continued)
Specifications with boldface type are for full operating temperature range, the other type are for TJ = 25ºC.
Symbol
Typ.
VMax
Unit
1.193
1.18
1.23
1.267
1.28
V
76
76
3.168
3.135
3.3
78
78
4.8
4.75
5
83
83
11.52
11.4
12
90
90
4.5V < VIN < 22V
0.2A < ILOAD < 2A
VOUT programmed for 3V
η
Efficiency
VIN = 12V, ILOAD=2A
Output Voltage
4.75V < VIN < 22V
0.2A < ILOAD < 2A
Efficiency
VIN = 12V, ILOAD = 2A
Output Voltage
7V < VIN < 22V
0.2A < ILOAD < 2A
Efficiency
VIN = 12V, ILOAD = 2A
Output Voltage
15V < VIN < 22V
0.2A < ILOAD < 2A
Efficiency
VIN = 15V, ILOAD = 2A
η
VOUT
η
VOUT
AP1509-12V
VMin
Output
Feedback
VOUT
AP1509-5V
Conditions
VFB
AP1509-ADJ
AP1509-3.3V
Parameter
η
AP1509
Document number: DS31016 Rev. 4 - 2
6 of 13
www.diodes.com
%
3.432
3.465
V
%
5.2
5.25
V
%
12.48
12.6
V
%
June 2010
© Diodes Incorporated
AP1509
150KHz, 2A PWM BUCK DC/DC CONVERTER
Typical Performance Characteristics
AP1509 Efficiency vs. Temperature
(VIN=12V, VOUT=5V, Io=2A)
AP1509 Efficiency vs. Temperature
(VIN=12V, VOUT=3.3V, Io=2A)
81
80
79
Efficiency (%)
Efficiency (%)
86
85
84
83
82
81
80
79
78
77
76
75
78
77
76
75
74
73
-50 -30 -10 10
-50 -30 -10 10 30 50 70 90 110 130 150
Temperature (TA) (°C)
50
70
90 110 130 150
Temperature (TA) (°C)
AP1509 Saturation Voltage vs. Temperature
(VIN =12V, VFB=0V, VSD=0)
AP1509 Switch Current Limit vs. Temperature
(VIN=12V, VFB=0V)
1.4
Switch Current Limit (A)
5.5
1.3
Saturation Voltage (V)
30
1.2
2A
1.1
1A
1
0.5A
0.9
0.8
5
4.5
4
3.5
3
0.7
-50
-25
0
25
50
75
100
-50
125
Temperature (TA) (°C)
-30
-10
10
30
50
70
90
Temperature (TA) (°C)
15
14
13
12
11
10
9
8
7
6
5
60
Supply Current (uA)
Supply Current (mA)
AP1509 Supply Current vs. Temperature
(VIN=12V, No Load, Von/off =0V(Switch ON) ,Von/off =5V(Switch OFF))
Switch ON
55
50
45
Switch OFF
40
35
30
-50 -30 -10 10
30
50
70
90 110 130 150
Document number: DS31016 Rev. 4 - 2
30
50
70
90 110 130 150
Temperature (TA) (°C)
Temperature (TA) (°C)
AP1509
-50 -30 -10 10
7 of 13
www.diodes.com
June 2010
© Diodes Incorporated
AP1509
150KHz, 2A PWM BUCK DC/DC CONVERTER
Typical Performance Characteristics (Continued)
AP1509 Threshold Voltage vs. Temperature
(VIN=12V, Io=100mA)
AP1509 ON/OFF Current vs. ON/OFF Voltage
(VIN=12V)
1.7
10
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
1.5
ON/OFF Current (nA)
Threshold Voltage (V)
1.6
1.4
1.3
1.2
1.1
1
0.9
0.8
-50 -30 -10 10
30
50
70
0
90 110 130 150
Temperature (TA) (°C)
6
9
12
15
18
21
ON/OFF Voltage (V)
AP1509 Frequency vs. Temperature
(VIN=12V, Io=500mA, VOUT=5V)
AP1509 Feedback Current vs. Temperature
(VIN=12V, VOUT=5V, Vfb=1.3V)
170
10
Feedback Current (nA)
165
Frequency (KHz)
3
160
155
150
145
140
0
-10
-20
-30
-40
-50
-50 -30 -10
10
30
50
70
90 110 130 150
Temperature (TA) (°C)
-50 -30 -10 10
30
50
70
90 110 130 150
Temperature (TA) (°C)
V OUT (V)
AP1509 Output Voltage vs. Temperature
(VIN=12V, Io=2A)
3.5
3.45
3.4
3.35
3.3
3.25
3.2
3.15
3.1
3.05
3
2.95
2.9
-40 -20
0
20
40
60
80 100 120 140 160
Temperature (TA) (°C)
AP1509
Document number: DS31016 Rev. 4 - 2
8 of 13
www.diodes.com
June 2010
© Diodes Incorporated
AP1509
150KHz, 2A PWM BUCK DC/DC CONVERTER
Typical Performance Characteristics (Continued)
Feedback Voltage vs. Temperature
(VIN=15V, VOUT=5V)
1.26
1000
900
800
700
600
500
400
300
200
100
0
Feedback Voltage (V)
Frequency (KHz)
Header Frequency vs. Temperature
1.25
1.24
1.23
1.22
-40
10
60
110
-40
o
60
110
Temperature ( C)
Supply Current vs. Supply Voltage
(VIN=15V, VOUT=5V, lOUT=0A)
Supply Current vs. Temperature
(VIN=15V, VOUT=5V, lOUT=0A)
3
3
2.5
2.5
Supply Current (mA)
Supply Current (mA)
10
o
Temperature ( C)
2
1.5
1
0.5
2
1.5
1
0.5
0
0
-40
10
o
60
0
110
5
Temperature ( C)
10
15
Supply Voltage (V)
Efficiency vs. Output Current
(VIN=15V, VOUT=3.3V)
Efficiency vs. Output Current
(VIN=15V, VOUT=5V)
90
85
Efficiency (%)
Efficiency (%)
85
80
75
75
65
55
70
0
20
40
60
Output Current (mA)
AP1509
Document number: DS31016 Rev. 4 - 2
0
20
40
60
Output Current (mA)
9 of 13
www.diodes.com
June 2010
© Diodes Incorporated
AP1509
150KHz, 2A PWM BUCK DC/DC CONVERTER
Functions Description
Pin Functions
+VIN
This is the positive input supply for the IC switching regulator. A suitable input bypass capacitor must be
presented at this pin to minimize voltage transients and to supply the switching currents needed by the
regulator.
Ground
Circuit ground.
Output
Internal switch. The voltage at this pin switches between (+VIN – VSAT) and approximately – 0.5V, with a duty
cycle of approximately VOUT / VIN. To minimize coupling to sensitive circuitry, the PC board copper area
connected to this pin should be minimized.
Feedback
Senses the regulated output voltage to complete the feedback loop.
SD
Allows the switching regulator circuit to be shutdown using logic level signals thus dropping the total input
supply current to approximately 150uA. Pulling this pin below a threshold voltage of approximately 1.3V turns
the regulator on, and pulling this pin above 1.3V (up to a maximum of 18V) shuts the regulator down. If this
shutdown feature is not needed, the SD pin can be wired to the ground pin.
Thermal Considerations
The SOP-8L package needs a heat sink under most conditions. The size of the heat sink depends on the input
voltage, the output voltage, the load current and the ambient temperature. The AP1509 junction temperature
rises above ambient temperature for a 2A load and different input and output voltages. The data for these
curves was taken with the AP1509 (SOP-8L package) operating as a buck-switching regulator in an ambient
temperature of 25oC (still air). These temperature increments are all approximate and are affected by many
factors. Higher ambient temperatures require more heat sinker.
For the best thermal performance, wide copper traces and generous amounts of printed circuit board copper
should be used in the board layout (One exception is the output (switch) pin, which should not have large areas
of copper). Large areas of copper provide the best transfer of heat (lower thermal resistance) to the surrounding
air, and moving air lowers the thermal resistance even further.
Package thermal resistance and junction temperature increments are all approximate. The increments are
affected by a lot of factors. Some of these factors include board size, shape, thickness, position, location, and
even board temperature. Other factors are, trace width, total printed circuit copper area, copper thickness,
single or double-sided, multi-layer board and the amount of solder on the board.
The effectiveness of the PC board to dissipate heat also depends on the size, quantity and spacing of other
components on the board, as well as whether the surrounding air is still or moving. Furthermore, some of these
components such as the catch diode will add heat to the PC board and the heat can vary as the input voltage
changes. For the inductor, depending on the physical size, type of core material and the DC resistance, it could
either act as a heat sink taking heat away from the board, or it could add heat to the board.
AP1509
Document number: DS31016 Rev. 4 - 2
10 of 13
www.diodes.com
June 2010
© Diodes Incorporated
AP1509
150KHz, 2A PWM BUCK DC/DC CONVERTER
Ordering Information
AP1509 - XX S X - 13
Output Version
Package
Lead Free
Packing
Blank : Adjustable
33 : 3.3V
50 : 5.0V
12 : 12V
S : SOP-8L
L : Lead Free
G : Green
13 : Tape & Reel
Device
AP1509-XXSL-13
AP1509-XXSG-13
Notes:
Package
Code
S
S
13” Tape and Reel
Quantity
Part Number Suffix
2500/Tape & Reel
-13
2500/Tape & Reel
-13
Packaging
(Note 2)
SOP-8L
SOP-8L
2. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at
http://www.diodes.com/datasheets/ap02001.pdf.
Marking Information
(1) SOP-8L
( Top View )
8
Logo
Part No.
Output Type :
Blank : Adjustable
1509-33 : 3.3V
1509-50 : 5.0V
1509-12 : 12V
AP1509
Document number: DS31016 Rev. 4 - 2
5
1509-XX
YY WW X X
1
4
11 of 13
www.diodes.com
L : Lead Free
G : Green
YY : Year : 08, 09,10~
WW : Week : 01~52; 52
represents 52 and 53 week
X : Internal Code
June 2010
© Diodes Incorporated
AP1509
150KHz, 2A PWM BUCK DC/DC CONVERTER
Package Outline Dimensions (All Dimensions in mm)
0.254
0.10/0.20
3.85/3.95
5.90/6.10
(1) Package Type: SOP-8L
Gauge Plane
Seating Plane
0.62/0.82
Detail "A"
7°~9°
0.15/0.25
1.30/1.50
1.75max.
0.35max. 45°
7°~9°
Detail "A"
0°/8°
0.3/0.5
1.27typ
4.85/4.95
5.4
8x-0.60
8x-1.55
6x-1.27
Land Pattern Recommendation
(Unit: mm)
AP1509
Document number: DS31016 Rev. 4 - 2
12 of 13
www.diodes.com
June 2010
© Diodes Incorporated
AP1509
150KHz, 2A PWM BUCK DC/DC CONVERTER
IMPORTANT NOTICE
DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS
DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).
Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other
changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability
arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any
license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described
herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies
whose products are represented on Diodes Incorporated website, harmless against all damages.
Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized
sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall
indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.
Products described herein may be covered by one or more United States, international or foreign patents pending. Product names
and markings noted herein may also be covered by one or more United States, international or foreign trademarks.
LIFE SUPPORT
Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without
the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:
A. Life support devices or systems are devices or systems which:
1. are intended to implant into the body, or
2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided
in the labeling can be reasonably expected to result in significant injury to the user.
B.
A critical component is any component in a life support device or system whose failure to perform can be reasonably expected
to cause the failure of the life support device or to affect its safety or effectiveness.
Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or
systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements
concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems,
notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further,
Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes
Incorporated products in such safety-critical, life support devices or systems.
Copyright © 2010, Diodes Incorporated
www.diodes.com
AP1509
Document number: DS31016 Rev. 4 - 2
13 of 13
www.diodes.com
June 2010
© Diodes Incorporated
Similar pages