Coilcraft LPS5010-472ML Shielded power inductor Datasheet

Document 536-1
Shielded Power Inductors–LPS5010 Series
• Very low DCR; excellent current handling
• 5.0 × 5.0 mm footprint; less than 1.0 mm tall
Designer’s Kit C407 contains 3 each of all values
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Terminations RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Weight 70 – 75 mg
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 1000/7″reel; 3000/13″ reel Plastic tape: 12 mm wide,
0.3 mm thick, 8 mm pocket spacing, 1.02 mm pocket depth
Recommended pick and place nozzle OD: 5 mm; ID: ≤ 2.5 mm
PCB washing Only pure water or alcohol recommended
DCR SRF
max3 typ4
±20% (µH) (Ohms) (MHz)
Inductance2
Part number1
LPS5010-471ML_
LPS5010-821ML_
LPS5010-152ML_
LPS5010-222ML_
LPS5010-332ML_
LPS5010-472ML_
LPS5010-562ML_
LPS5010-682ML_
LPS5010-103ML_
LPS5010-153ML_
0.47
0.82
1.5
2.2
3.3
4.7
5.6
6.8
10
15
Isat (A)5
10% 20% 30%
drop drop drop
Irms (A)6
20°C 40°C
rise rise
0.038
0.058
0.072
0.100
0.125
290
195
168
144
105
3.1
2.3
1.7
1.4
1.1
3.3
2.5
1.8
1.5
1.2
3.4
2.6
1.9
1.6
1.3
2.0
1.2
0.90
0.88
0.86
2.7
1.5
1.4
1.2
1.1
0.175
0.240
0.255
0.350
0.500
76
75
71
51
39
0.95
0.90
0.82
0.66
0.55
1.1
0.97
0.90
0.72
0.59
1.1
1.00
0.93
0.74
0.62
0.85
0.75
0.74
0.73
0.68
0.98
0.92
0.85
0.80
0.75
0.670
1.05
1.45
2.00
3.10
32
26
20
15
12
0.47
0.38
0.31
0.26
0.21
0.51
0.42
0.34
0.29
0.23
0.53
0.43
0.36
0.30
0.24
0.46
0.40
0.33
0.25
0.21
0.62
0.55
0.44
0.35
0.28
11
9.0
7.0
5.5
4.5
0.20
0.18
0.15
0.12
0.090
0.22
0.20
0.16
0.13
0.11
0.23
0.21
0.17
0.14
0.11
0.19
0.17
0.15
0.13
0.11
0.25
0.23
0.20
0.185
0.150
LPS5010-223ML_
LPS5010-333ML_
LPS5010-473ML_
LPS5010-683ML_
LPS5010-104ML_
22
33
47
68
100
LPS5010-124ML_
LPS5010-154ML_
LPS5010-224ML_
LPS5010-334ML_
LPS5010-474ML_
120
150
220
330
470
3.50
4.25
6.25
8.60
12.7
LPS5010-564ML_
LPS5010-684ML_
LPS5010-105ML_
560
680
1000
15.7
20.0
28.0
4.0 0.090 0.10
0.10
3.7 0.090 0.097 0.10
3.0 0.087 0.096 0.10
0.10 0.135
0.090 0.125
0.080 0.110
1. Please specify termination and packaging codes:
LPS5010-105MLC
Termination: L = RoHS compliant silver-palladiumplatinum-glass frit.
Special order:
T = RoHS tin-silver-copper (95.5/4/0.5)
or S = non-RoHS tin-lead (63/37).
Packaging: C= 7″ machine-ready reel. EIA-481
embossed plastic tape (1000 parts
per full reel).
B= Less than full reel. In tape, but not
machine ready.
To have a leader and trailer added
($25 charge), use code letter C
instead.
D= 13″ machine-ready reel. EIA-481
embossed plastic tape. Factory
order only, not stocked (3500 parts
per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms using an
Agilent/HP 4192A. Inductance at 1 MHz is the same
for parts with SRF ≥10 MHz.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using Agilent/HP 8753ES or equivalent.
5. DC current that causes the specified inductance drop
from its value without current.
6. Current that causes the specified temperature rise
from 25°C ambient.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components”
before soldering.
Specifications subject to change without notice.
Please check our website for latest information.
© Coilcraft, Inc. 2009
Document 536-1
Revised 10/06/08
Document 536-2
Shielded SMT Power Inductors – LPS5010 Series
Typical L vs Current
Typical L vs Frequency
10000
10000
1000 µH
100
100 µH
10
10 µH
1
0.1
1
0.1
100 µH
100
10 µH
10
0.82 µH
1
0.82 µH
0.01
1000 µH
1000
Inductance (µH)
Inductance (µH)
1000
10
0.1
0.01
10
Frequency (MHz)
0.189 ±0.003*
4,80 ±0,076
Current Derating
120
110
100
0.189 ±0.003*
4,80 ±0,076
XXX X
90
80
70
Dash
number
60
Winding
direction
Internal
code
Recommended
Land Pattern
50
40
30
20
25°C
Percent of rated current
1
0.1
Current (A)
Isat
Irms
10
0
-40
-20
0
20
0.060
1,50
40
60
80
100
0.138
3,50
0.090
2,30
0.0354 ±0.004
0,90 ±0,10
45°
typ
120 140
Ambient temperature (°C)
0.039 typ
1,00
0.039 typ
1,00
are of the case not
* Dimensions
including the termination. For maximum
overall dimensions including the
termination, add 0.005 in / 0,13 mm.
Dimensions are in
0.060
1,50
0.134
3,40
0.197
5,00
inches
mm
Specifications subject to change without notice.
Please check our website for latest information.
© Coilcraft, Inc. 2009
0.197
5,00
0.134 0.090
3,40 2,30
Document 536-2
Revised 10/06/08
Similar pages