Maxim MAX3485EESA 3.3v-powered, â±15kv esd-protected, 12mbps and slew-rate-limited true rs-485/rs-422 transceiver Datasheet

19-1474; Rev 0; 4/99
3.3V-Powered, ±15kV ESD-Protected, 12Mbps and
Slew-Rate-Limited True RS-485/RS-422 Transceivers
Devices in the MAX3483E family (MAX3483E/MAX3485E/
MAX3486E/MAX3488E/MAX3490E/MAX3491E) are
±15kV ESD-protected, +3.3V, low-power transceivers for
RS-485 and RS-422 communications. Each device contains one driver and one receiver. The MAX3483E and
MAX3488E feature slew-rate-limited drivers that minimize
EMI and reduce reflections caused by improperly terminated cables, allowing error-free data transmission at
data rates up to 250kbps. The partially slew-rate-limited
MAX3486E transmits up to 2.5Mbps. The MAX3485E,
MAX3490E, and MAX3491E transmit at up to 12Mbps.
All devices feature enhanced electrostatic discharge
(ESD) protection. All transmitter outputs and receiver
inputs are protected to ±15kV using IEC 1000-4-2 AirGap Discharge, ±8kV using IEC 1000-4-2 Contact
Discharge, and ±15kV using the Human Body Model.
Drivers are short-circuit current limited and are protected against excessive power dissipation by thermal
shutdown circuitry that places the driver outputs into a
high-impedance state. The receiver input has a fail-safe
feature that guarantees a logic-high output if both
inputs are open circuit.
The MAX3488E, MAX3490E, and MAX3491E feature
full-duplex communication, while the MAX3483E,
MAX3485E, and MAX3486E are designed for halfduplex communication.
Features
♦ ESD Protection for RS-485 I/O Pins
±15kV—Human Body Model
±8kV—IEC 1000-4-2, Contact Discharge
±15kV—IEC 1000-4-2, Air-Gap Discharge
♦ Operate from a Single +3.3V Supply—
No Charge Pump Required
♦ Interoperable with +5V Logic
♦ Guaranteed 12Mbps Data Rate
(MAX3485E/MAX3490E/MAX3491E)
♦ Slew-Rate Limited for Errorless Data Transmission
(MAX3483E/MAX3488E)
♦ 2nA Low-Current Shutdown Mode
(MAX3483E/MAX3485E/MAX3486E/MAX3491E)
♦ -7V to +12V Common-Mode Input Voltage Range
♦ Full-Duplex and Half-Duplex Versions Available
♦ Industry-Standard 75176 Pinout
(MAX3483E/MAX3485E/MAX3486E)
♦ Current-Limiting and Thermal Shutdown for
Driver Overload Protection
Ordering Information
Applications
PART
TEMP. RANGE
MAX3483ECSA
0°C to +70°C
PIN-PACKAGE
8 SO
MAX3483ECPA
0°C to +70°C
8 Plastic DIP
Transceivers for EMI-Sensitive Applications
MAX3483EESA
MAX3483EEPA
MAX3485ECSA
-40°C to +85°C
-40°C to +85°C
0°C to +70°C
8 SO
8 Plastic DIP
8 SO
Integrated Services Digital Networks
MAX3485ECPA
0°C to +70°C
8 Plastic DIP
Packet Switching
MAX3485EESA
MAX3485EEPA
-40°C to +85°C
-40°C to +85°C
8 SO
8 Plastic DIP
Telecommunications
Industrial-Control Local Area Networks
Ordering Information continued at end of data sheet.
Selector Guide
PART
NUMBER
GUARANTEED SUPPLY
DATA RATE
VOLTAGE
(Mbps)
(V)
DRIVER/ SHUTDOWN
±15kV
HALF/FULL SLEW-RATE
RECEIVER CURRENT
ESD
DUPLEX
LIMITED
ENABLE
(nA)
PROTECTION
PIN
COUNT
MAX3483E
0.25
Half
Yes
Yes
2
Yes
8
MAX3485E
12
Half
No
Yes
2
Yes
8
Half
Yes
Yes
2
Yes
8
Full
Yes
No
—
Yes
8
MAX3486E
2.5
MAX3488E
0.25
MAX3490E
12
Full
No
No
—
Yes
8
MAX3491E
12
Full
No
Yes
2
Yes
14
3.0 to 3.6
________________________________________________________________ Maxim Integrated Products
1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
MAX3483E/MAX3485E/MAX3486E/MAX3488E/MAX3490E/MAX3491E
General Description
MAX3483E/MAX3485E/MAX3486E/MAX3488E/MAX3490E/MAX3491E
3.3V-Powered, ±15kV ESD-Protected, 12Mbps and
Slew-Rate-Limited True RS-485/RS-422 Transceivers
ABSOLUTE MAXIMUM RATINGS
Supply Voltage (VCC).............................................................+7V
Control Input Voltage (RE, DE).................................-0.3V to +7V
Driver Input Voltage (DI)...........................................-0.3V to +7V
Driver Output Voltage (A, B, Y, Z) .......................-7.5V to +12.5V
Receiver Input Voltage (A, B)..............................-7.5V to +12.5V
Receiver Output Voltage (RO)....................-0.3V to (VCC + 0.3V)
Continuous Power Dissipation (TA = +70°C)
8-Pin SO (derate 5.88mW/°C above +70°C)..................471mW
8-Pin Plastic DIP (derate 9.09mW/°C above +70°C) .....727mW
14-Pin SO (derate 8.33mW/°C above +70°C)................667mW
14-Pin Plastic DIP (derate 10mW/°C above +70°C) ......800mW
Operating Temperature Ranges
MAX34_ _ EC_ _ ...................................................0°C to +70°C
MAX34_ _ EE_ _.................................................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(VCC = +3.3V ±0.3V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
Differential Driver Output
SYMBOL
VOD
CONDITIONS
RL = 100Ω (RS-422), Figure 4
RL = 54Ω (RS-485), Figure 4
RL = 60Ω (RS-485), VCC = 3.3V, Figure 5
MIN
TYP
MAX
2.0
1.5
1.5
UNITS
V
Change in Magnitude of Driver
Differential Output Voltage for
Complementary Output States
(Note 1)
∆VOD
RL = 54Ω or 100Ω, Figure 4
0.2
V
Driver Common-Mode Output
Voltage
VOC
RL = 54Ω or 100Ω, Figure 4
3
V
∆VOC
RL = 54Ω or 100Ω, Figure 4
0.2
V
Change in Magnitude of
Common-Mode Output Voltage
(Note 1)
Input High Voltage
VIH
DE, DI, RE
Input Low Voltage
VIL
DE, DI, RE
Logic Input Current
IIN1
IIN2
DE = 0,
VCC = 0 or 3.6V
Input Current (A, B)
Output Leakage (Y, Z)
IO
Output Leakage (Y, Z)
in Shutdown Mode
IO
Receiver Differential
Threshold Voltage
VTH
2.0
V
0.8
V
DE, DI, RE
±2
µA
VIN = 12V
VIN = -7V
VOUT = 12V
DE = 0, RE = 0,
VCC = 0 or 3.6V, MAX3491E VOUT = -7V
VOUT = 12V
DE = 0, RE = VCC,
VCC = 0 or 3.6V, MAX3491E VOUT = -7V
1.0
-0.8
20
-20
1
-1
-7V ≤ VCM ≤ 12V
-0.2
0.2
mA
µA
µA
V
Receiver Input Hysteresis
∆VTH
VCM = 0
Receiver Output High Voltage
VOH
IOUT = -1.5mA, VID = 200mV, Figure 6
Receiver Output Low Voltage
VOL
IOUT = 2.5mA, VID = 200mV, Figure 6
0.4
V
Three-State (High-Impedance)
Output Current at Receiver
IOZR
VCC = 3.6V, 0 ≤ VOUT ≤ VCC
±1
µA
Receiver Input Resistance
RIN
-7V ≤ VCM ≤ 12V
Supply Voltage Range
VCC
Supply Current
ICC
Supply Current in Shutdown Mode
2
ISHDN
50
mV
VCC - 0.4
V
12
kΩ
3.0
3.6
DE = VCC, RE = 0 or VCC
1.1
2.2
DE = 0, RE = 0
0.95
1.9
DE = 0, RE = VCC, DI = VCC or 0
0.002
1
No load,
DI = 0 or VCC
_______________________________________________________________________________________
V
mA
µA
3.3V-Powered, ±15kV ESD-Protected, 12Mbps and
Slew-Rate-Limited True RS-485/RS-422 Transceivers
MAX3483E/MAX3485E/MAX3486E/MAX3488E/MAX3490E/MAX3491E
DC ELECTRICAL CHARACTERISTICS (continued)
(VCC = +3.3V ±0.3V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
Driver Short-Circuit Output Current
IOSD
Receiver Short-Circuit Output Current
IOSR
ESD Protection for Y, Z, A, B
CONDITIONS
VOUT = -7V
VOUT = 12V
0 ≤ VRO ≤ VCC
IEC 1000-4-2 Air Discharge
MIN
TYP
±8
MAX
-250
250
±60
UNITS
mA
mA
±15
IEC 1000-4-2 Contact Discharge
(MAX3483E, MAX3485E,
MAX3486E, MAX3491E)
±8
IEC 1000-4-2 Contact Discharge
(MAX3490E, MAX3488E)*
±6
Human Body Model
±15
kV
*MAX3488E and MAX3491E will be compliant to ±8kV per IEC 1000-4-2 Contact Discharge by September 1999.
DRIVER SWITCHING CHARACTERISTICS—MAX3485E/MAX3490E/MAX3491E
(VCC = +3.3V, TA = +25°C.)
PARAMETER
Maximum Data Rate
Driver Differential Output Delay
Driver Differential Output Transition Time
Driver Propagation Delay, Low-to-High Level
Driver Propagation Delay, High-to-Low Level
|tPLH - tPHL| Driver Propagation-Delay Skew (Note 2)
SYMBOL
tDD
tTD
tPLH
tPHL
tPDS
CONDITIONS
RL = 60Ω, Figure 7
RL = 60Ω, Figure 7
RL = 27Ω, Figure 8
RL = 27Ω, Figure 8
RL = 27Ω, Figure 8
MIN
TYP
MAX
UNITS
12
1
3
7
7
15
22
11
23
23
-1.4
35
25
35
35
±8
Mbps
ns
ns
ns
ns
ns
42
42
35
35
650
650
90
90
80
80
900
900
ns
ns
ns
ns
ns
ns
TYP
MAX
42
28
42
42
-6
70
60
75
75
±12
UNITS
Mbps
ns
ns
ns
ns
ns
52
52
40
40
700
700
100
100
80
80
1000
1000
ns
ns
ns
ns
ns
ns
DRIVER-OUTPUT ENABLE/DISABLE TIMES (MAX3485E/MAX3491E only)
Driver-Output Enable Time to Low Level
Driver-Output Enable Time to High Level
Driver-Output Disable Time from High Level
Driver-Output Disable Time from Low Level
Driver-Output Enable Time from Shutdown to Low Level
Driver-Output Enable Time from Shutdown to High Level
tPZL
tPZH
tPHZ
tPLZ
tPSL
tPSH
RL = 110Ω, Figure 10
RL = 110Ω, Figure 9
RL = 110Ω, Figure 9
RL = 110Ω, Figure 10
RL = 110Ω, Figure 10
RL = 110Ω, Figure 9
DRIVER SWITCHING CHARACTERISTICS—MAX3486E
(VCC = +3.3V, TA = +25°C.)
PARAMETER
Maximum Data Rate
Driver Differential Output Delay
Driver Differential Output Transition Time
Driver Propagation Delay, Low-to-High Level
Driver Propagation Delay, High-to-Low Level
SYMBOL
CONDITIONS
|tPLH - tPHL| Driver Propagation-Delay Skew (Note 2)
tDD
tTD
tPLH
tPHL
tPDS
RL = 60Ω, Figure 7
RL = 60Ω, Figure 7
RL = 27Ω, Figure 8
RL = 27Ω, Figure 8
RL = 27Ω, Figure 8
DRIVER-OUTPUT ENABLE/DISABLE TIMES
Driver-Output Enable Time to Low Level
Driver-Output Enable Time to High Level
Driver-Output Disable Time from High Level
Driver-Output Disable Time from Low Level
Driver-Output Enable Time from Shutdown to Low Level
Driver-Output Enable Time from Shutdown to High Level
tPZL
tPZH
tPHZ
tPLZ
tPSL
tPSH
RL = 110Ω, Figure 10
RL = 110Ω, Figure 9
RL = 110Ω, Figure 9
RL = 110Ω, Figure 10
RL = 110Ω, Figure 10
RL = 110Ω, Figure 9
MIN
2.5
20
15
20
20
_______________________________________________________________________________________
3
MAX3483E/MAX3485E/MAX3486E/MAX3488E/MAX3490E/MAX3491E
3.3V-Powered, ±15kV ESD-Protected, 12Mbps and
Slew-Rate-Limited True RS-485/RS-422 Transceivers
DRIVER SWITCHING CHARACTERISTICS—MAX3483E/MAX3488E
(VCC = +3.3V, TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
Maximum Data Rate
MIN
TYP
MAX
250
UNITS
kbps
Driver Differential Output Delay
tDD
RL = 60Ω, Figure 7
600
900
1400
ns
Driver Differential Output Transition Time
tTD
RL = 60Ω, Figure 7
400
740
1200
ns
Driver Propagation Delay, Low-to-High Level
tPLH
RL = 27Ω, Figure 8
700
930
1500
ns
Driver Propagation Delay, High-to-Low Level
tPHL
RL = 27Ω, Figure 8
700
930
1500
ns
|tPLH - tPHL| Driver Propagation-Delay Skew (Note 2)
tPDS
RL = 27Ω, Figure 8
±50
ns
DRIVER-OUTPUT ENABLE/DISABLE TIMES (MAX3483E only)
Driver-Output Enable Time to Low Level
tPZL
RL = 110Ω, Figure 10
900
1300
ns
Driver-Output Enable Time to High Level
tPZH
RL = 110Ω, Figure 9
600
800
ns
Driver-Output Disable Time from High Level
tPHZ
RL = 110Ω, Figure 9
50
80
ns
Driver-Output Disable Time from Low Level
tPLZ
RL = 110Ω, Figure 10
50
80
ns
Driver-Output Enable Time from Shutdown to Low Level
tPSL
RL = 110Ω, Figure 10
1.9
2.7
µs
Driver-Output Enable Time from Shutdown to High Level
tPSH
RL = 110Ω, Figure 9
2.2
3.0
µs
MIN
TYP
MAX
MAX3483E/MAX3485E/MAX3486E/MAX3491E
only (Note 3)
80
190
300
VID = 0 to 3.0V, CL = 15pF, Figure 11
25
62
90
MAX3483E/MAX3488E
25
75
120
VID = 0 to 3.0V, CL = 15pF, Figure 11
25
62
90
MAX3483E/MAX3488E
25
75
120
VID = 0 to 3.0V, CL = 15pF, Figure 11
6
±10
MAX3483E/MAX3488E
12
±20
RECEIVER SWITCHING CHARACTERISTICS
(VCC = +3.3V, TA = +25°C.)
PARAMETER
SYMBOL
Time to Shutdown
tSHDN
Receiver Propagation Delay,
Low-to-High Level
tRPLH
Receiver Propagation Delay,
High-to-Low Level
tRPHL
|tPLH - tPHL| Receiver
tRPDS
Propagation-Delay Skew
CONDITIONS
UNITS
ns
ns
ns
ns
Receiver-Output Enable Time
to Low Level
tPRZL
CL = 15pF, Figure 12,
MAX3483E/85E/86E/91E only
25
50
ns
Receiver-Output Enable Time
to High Level
tPRZH
CL = 15pF, Figure 12,
MAX3483E/85E/86E/91E only
25
50
ns
Receiver-Output Disable
Time from High Level
tPRHZ
CL = 15pF, Figure 12,
MAX3483E/85E/86E/91E only
25
45
ns
Receiver-Output Disable
Time from Low Level
tPRLZ
CL = 15pF, Figure 12,
MAX3483E/85E/86E/91E only
25
45
ns
Receiver-Output Enable Time
from Shutdown to Low Level
tPRSL
CL = 15pF, Figure 12,
MAX3483E/85E/86E/91E only
720
1400
ns
Receiver-Output Enable Time
from Shutdown to High Level
tPRSH
CL = 15pF, Figure 12,
MAX3483E/85E/86E/91E only
720
1400
ns
Note 1: ∆VOD and ∆VOC are the changes in VOD and VOC, respectively, when the DI input changes state.
Note 2: Measured on |tPLH (Y) - tPHL (Y)| and |tPLH (Z) - tPHL (Z)|.
Note 3: The transceivers are put into shutdown by bringing RE high and DE low. If the inputs are in this state for less than 80ns, the
devices are guaranteed not to enter shutdown. If the inputs are in this state for at least 300ns, the devices are guaranteed
to have entered shutdown. See Low-Power Shutdown Mode section.
4
_______________________________________________________________________________________
3.3V-Powered, ±15kV ESD-Protected, 12Mbps and
Slew-Rate-Limited True RS-485/RS-422 Transceivers
-18
OUTPUT CURRENT (mA)
15
10
3.30
-14
-12
-10
-8
-6
-4
5
IRO = 1.5mA
3.25
OUTPUT HIGH VOLTAGE (V)
-16
20
OUTPUT CURRENT (mA)
RECEIVER OUTPUT HIGH VOLTAGE
vs. TEMPERATURE
MAX3483E-02
-20
MAX3483E-01
25
OUTPUT CURRENT vs.
RECEIVER OUTPUT HIGH VOLTAGE
MAX3483E-03
OUTPUT CURRENT vs.
RECEIVER OUTPUT LOW VOLTAGE
3.20
3.15
3.10
3.05
-2
0
0.5
1.0
1.5
2.0
2.5
3.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
-20
0
20
40
60
80
OUTPUT HIGH VOLTAGE (V)
TEMPERATURE (°C)
RECEIVER OUTPUT LOW VOLTAGE
vs. TEMPERATURE
DRIVER OUTPUT CURRENT vs.
DIFFERENTIAL OUTPUT VOLTAGE
DRIVER DIFFERENTIAL OUTPUT
VOLTAGE vs. TEMPERATURE
90
80
OUTPUT CURRENT (mA)
0.6
0.5
0.4
0.3
0.2
70
60
50
40
30
20
10
0
0
-20
0
20
40
60
80
1.0
1.5
2.0
2.5
3.0
3.5
DIFFERENTIAL OUTPUT VOLTAGE (V)
2.1
2.0
1.9
1.8
-40
-20
0
20
40
60
80
100
OUTPUT CURRENT vs.
DRIVER OUTPUT HIGH VOLTAGE
MAX3483E-07
-100
-80
OUTPUT CURRENT (mA)
OUTPUT CURRENT (mA)
2.2
TEMPERATURE (°C)
OUTPUT CURRENT vs.
DRIVER OUTPUT LOW VOLTAGE
150
2.3
1.6
0.5
TEMPERATURE (°C)
175
2.4
1.7
0
100
R = 54Ω
2.5
100
MAX3483E-08
0.1
2.6
DIFFERENTIAL OUTPUT VOLTAGE (V)
0.7
100
MAX3483E-05
IRO = 2.5mA
-40
-40
OUTPUT LOW VOLTAGE (V)
0.8
OUTPUT LOW VOLTAGE (V)
3.00
0
3.5
MAX3483E-04
0
MAX3483E-06
0
125
100
75
50
-60
-40
-20
25
0
0
0
2
4
6
8
OUTPUT LOW VOLTAGE (V)
10
12
-7 -6 -5 -4 -3 -2 -1 0 1 2 3
OUTPUT HIGH VOLTAGE (V)
4
5
_______________________________________________________________________________________
5
MAX3483E/MAX3485E/MAX3486E/MAX3488E/MAX3490E/MAX3491E
Typical Operating Characteristics
(VCC = +3.3V, TA = +25°C, unless otherwise noted.)
Typical Operating Characteristics (continued)
(VCC = +3.3V, TA = +25°C, unless otherwise noted.)
SHUTDOWN CURRENT
vs. TEMPERATURE
SUPPLY CURRENT
vs. TEMPERATURE
X = DON’T CARE
90
SHUTDOWN CURRENT (nA)
1.1
DE = VCC, RE = X
1.0
MAX3483E-10
100
MAX3483E-09
1.2
SUPPLY CURRENT (mA)
MAX3483E/MAX3485E/MAX3486E/MAX3488E/MAX3490E/MAX3491E
3.3V-Powered, ±15kV ESD-Protected, 12Mbps and
Slew-Rate-Limited True RS-485/RS-422 Transceivers
DE = 0, RE = 0
0.9
80
70
60
50
40
30
20
0.8
10
0.7
0
-40
-20
0
20
40
60
80
-40
100
-20
0
20
40
60
80
100
TEMPERATURE (°C)
TEMPERATURE (°C)
Pin Description
PIN
6
MAX3483E
MAX3485E
MAX3486E
MAX3488E
MAX3490E
MAX3491E
1
2
2
—
NAME
FUNCTION
2
RO
Receiver Output. If A > B by 200mV, RO will be high; if A < B by 200mV,
RO will be low.
3
RE
Receiver Output Enable. RO is enabled when RE is low; RO is high impedance when RE is high. If RE is high and DE is low, the device will enter a
low-power shutdown mode.
3
—
4
DE
Driver Output Enable. The driver outputs are enabled by bringing DE high.
They are high impedance when DE is low. If RE is high and DE is low, the
device will enter a low-power shutdown mode. If the driver outputs are
enabled, the parts function as line drivers. While they are high impedance,
they function as line receivers if RE is low.
4
3
5
DI
Driver Input. A low on DI forces output Y low and output Z high. Similarly, a
high on DI forces output Y high and output Z low.
5
4
6, 7
GND
—
5
9
Y
Noninverting Driver Output
—
6
10
Z
Inverting Driver Output
6
—
—
A
Noninverting Receiver Input and Noninverting Driver Output
—
8
12
A
Noninverting Receiver Input
7
—
—
B
Inverting Receiver Input and Inverting Driver Output
—
7
11
B
Inverting Receiver Input
8
1
13, 14
VCC
Positive Supply: 3.0V ≤ VCC ≤ 3.6V. Do not operate device with VCC > 3.6V.
—
—
1, 8
N.C.
No Connection. Not internally connected.
Ground
_______________________________________________________________________________________
3.3V-Powered, ±15kV ESD-Protected, 12Mbps and
Slew-Rate-Limited True RS-485/RS-422 Transceivers
MAX3483E/MAX3485E/MAX3486E/MAX3488E/MAX3490E/MAX3491E
TOP VIEW
R
1
8
VCC
RO
RE 2
7
B
RE 2
DE 3
6
A
DE 3
5
GND
DI 4
RO
1
DI 4
D
R
8 VCC
7 B
Rt
6
A
5 GND
D
DE
MAX3483E
MAX3485E
MAX3486E
D
DI
B
Rt
A
RO
R
RE
SO/DIP
NOTE: PIN LABELS Y AND Z ON TIMING, TEST, AND WAVEFORM DIAGRAMS REFER TO PINS A AND B WHEN DE IS HIGH.
Figure 1. MAX3483E/MAX3485E/MAX3486E Pin Configuration and Typical Operating Circuit
VCC
VCC
TOP VIEW
MAX3488E
MAX3490E
1
5 Y
8
A
RO 2
7
B
DI 3
6
Z
VCC 1
GND 4
R
5
D
DI
3
Rt
D
6 Z
R
RO
8 A
RO
Y
2
Rt
R
D
7
DI
B
SO/DIP
4
GND
GND
Figure 2. MAX3488E/MAX3490E Pin Configuration and Typical Operating Circuit
TOP VIEW
DE
VCC
4
N.C. 1
RO 2
14 VCC
R
13 VCC
RE 3
12 A
DE 4
11 B
DI 5
GND 6
10 Z
D
GND 7
SO/DIP
9
Y
8
N.C.
VCC RE
9
DI
5
MAX3491E
13, 14
Y
Rt
D
10
RO
R
Z
12
RO
2
R
A
Rt
D
11
DI
B
N.C.
1, 8
3
6, 7
RE GND
GND
DE
Figure 3. MAX3491E Pin Configuration and Typical Operating Circuit
_______________________________________________________________________________________
7
MAX3483E/MAX3485E/MAX3486E/MAX3488E/MAX3490E/MAX3491E
3.3V-Powered, ±15kV ESD-Protected, 12Mbps and
Slew-Rate-Limited True RS-485/RS-422 Transceivers
375Ω
RL
2
VOD
D
D
RL
VCC
2
VOC
VCC
Figure 4. Driver VOD and VOC
VID
VCM =
-7V to +12V
RL
VOD
375Ω
Figure 5. Driver VOD with Varying Common-Mode Voltage
R
0
VOL
IOL
(+)
VOH
IOH
(-)
Figure 6. Receiver VOH and VOL
3V
IN
1.5V
1.5V
CL
D
GENERATOR
(NOTE 4)
0
RL =
60Ω
OUT
tDD
tDD
≈ 2.0V
50Ω
90%
VCC
OUT
CL
CL = 15pF (NOTE 5)
50%
10%
90%
50%
10%
tTD
Figure 7. Driver Differential Output Delay and Transition Times
8
_______________________________________________________________________________________
tTD
≈ -2.0V
3.3V-Powered, ±15kV ESD-Protected, 12Mbps and
Slew-Rate-Limited True RS-485/RS-422 Transceivers
MAX3483E/MAX3485E/MAX3486E/MAX3488E/MAX3490E/MAX3491E
3V
VOM
IN
1.5V
1.5V
RL = 27Ω
0V
S1
GENERATOR
(NOTE 4)
tPLH
OUT
D
50Ω
CL = 15pF
(NOTE 5)
VCC
tPHL
VOH
Y
OUT
VOM
VOM
VOL
VOM =
VOH + VOL
2
tPHL
≈ 1.5V
tPLH
VOH
Z
OUT
VOM
VOM
VOL
Figure 8. Driver Propagation Times
3V
S1
0 OR 3V
OUT
D
IN
1.5V
1.5V
0
GENERATOR
(NOTE 4)
RL = 110Ω
CL = 50pF
(NOTE 5)
tPZH
tPHZ
50Ω
0.25V
OUT
VOM =
VOH + VOL
2
VOH
VOM
≈ 1.5V
0
Figure 9. Driver Enable and Disable Times (tPZH, tPSH, tPHZ)
VCC
3V
RL = 110Ω
S1
0 OR 3V
IN
1.5V
1.5V
0
OUT
D
tPSL
tPLZ
CL = 50pF
(NOTE 5)
GENERATOR
(NOTE 4)
VCC
OUT
50Ω
VOM
0.25V
VOL
Figure 10. Driver Enable and Disable Times (tPZL, tPSL, tPLZ)
_______________________________________________________________________________________
9
MAX3483E/MAX3485E/MAX3486E/MAX3488E/MAX3490E/MAX3491E
3.3V-Powered, ±15kV ESD-Protected, 12Mbps and
Slew-Rate-Limited True RS-485/RS-422 Transceivers
3.0V
GENERATOR
(NOTE 4)
VID
OUT
R
IN
50Ω
1.5V
1.5V
CL = 15pF
(NOTE 5)
0
tRPLH
tRPHL
VCC
1.5V
VOM =
0
VOM
OUT
VCC
2
VOM
0
Figure 11. Receiver Propagation Delay
S1
S3
1.5V
VCC
1k
-1.5V
VID
R
S2
CL
(NOTE 5)
GENERATOR
(NOTE 4)
50Ω
3V
IN
1.5V
0
3V
S1 OPEN
S2 CLOSED
S3 = 1.5V
IN
1.5V
0
tPRZH
tPRSH
tPRZL
tPRSL
VOH
OUT
VCC
OUT
1.5V
1.5V
0
VOL
3V
IN
1.5V
0
3V
S1 OPEN
S2 CLOSED
S3 = 1.5V
IN
1.5V
0
tPRHZ
OUT 0.25V
S1 CLOSED
S2 OPEN
S3 = -1.5V
S1 CLOSED
S2 OPEN
S3 = -1.5V
tPRLZ
VOH
VCC
OUT
0
0.25V
VOL
Figure 12. Receiver Enable and Disable Times
Note 4: The input pulse is supplied by a generator with the following characteristics: f = 250kHz, 50% duty cycle, t r ≤ 6.0ns, ZO = 50Ω.
Note 5: CL includes probe and stray capacitance.
10
______________________________________________________________________________________
3.3V-Powered, ±15kV ESD-Protected, 12Mbps and
Slew-Rate-Limited True RS-485/RS-422 Transceivers
___________Applications Information
Devices with Receiver/Driver Enable
(MAX3483E/MAX3485E/MAX3486E/MAX3491E)
The MAX3483E/MAX3485E/MAX3486E/MAX3488E/
MAX3490E/MAX3491E are low-power transceivers for
RS-485 and RS-422 communications. The MAX3483E
and MAX3488E can transmit and receive at data rates
up to 250kbps, the MAX3486E at up to 2.5Mbps, and the
MAX3485E/MAX3490E/MAX3491E at up to 12Mbps. The
MAX3488E/MAX3490E/MAX3491E are full-duplex transceivers, while the MAX3483E/MAX3485E/MAX3486E are
half-duplex. Driver Enable (DE) and Receiver Enable
(RE) pins are included on the MAX3483E/MAX3485E/
MAX3486E/MAX3491E. When disabled, the driver and
receiver outputs are high impedance.
Table 1. Transmitting
INPUTS
OUTPUTS
MODE
RE
DE
DI
B*
A*
X
1
1
0
1
Normal
X
1
0
1
0
Normal
0
0
X
High-Z
High-Z
Normal
1
0
X
High-Z
High-Z
Shutdown
* B and A outputs are Z and Y, respectively, for full-duplex part
(MAX3491E).
X = Don’t care; High-Z = High impedance
Table 2. Receiving
INPUTS
OUTPUTS
MODE
RE
DE
A, B
RO
0
0*
≥ +0.2V
1
Normal
0
0*
≤ -0.2V
0
Normal
0
0*
Inputs Open
1
Normal
1
0
X
High-Z
Shutdown
* DE is a “don’t care” (x) for the full-duplex part (MAX3491E).
X = Don’t care; High-Z = High impedance
Devices without Receiver/Driver Enable
(MAX3488E/MAX3490E)
Table 3. Transmitting
INPUT
Table 4. Receiving
INPUTS
OUTPUT
DI
OUTPUTS
Z
Y
A, B
RO
1
0
1
≥ +0.2V
1
0
1
0
≤ -0.2V
0
Inputs Open
1
10dB/div
Reduced EMI and Reflections
(MAX3483E/MAX3486E/MAX3488E)
The MAX3483E/MAX3488E are slew-rate limited, minimizing EMI and reducing reflections caused by improperly terminated cables. Figure 13 shows the driver
output waveform of a MAX3485E/MAX3490E/MAX3491E
transmitting a 125kHz signal, as well as the Fourier
analysis of that waveform. High-frequency harmonics
with large amplitudes are evident. Figure 14 shows the
same information, but for the slew-rate-limited
MAX3483E/MAX3488E transmitting the same signal. The
high-frequency harmonics have much lower amplitudes,
and the potential for EMI is significantly reduced.
Low-Power Shutdown Mode
(MAX3483E/MAX3485E/MAX3486E/MAX3491E)
A low-power shutdown mode is initiated by bringing both
RE high and DE low. The devices will not shut down
unless both the driver and receiver are disabled (high
impedance). In shutdown, the devices typically draw
only 2nA of supply current.
For these devices, the t PSH and t PSL enable times
assume the part was in the low-power shutdown mode;
the tPZH and tPZL enable times assume the receiver or
driver was disabled, but the part was not shut down.
10dB/div
0
500kHz/div
5MHz
Figure 13. Driver Output Waveform and FFT Plot of MAX3485E/
MAX3490E/MAX3491E Transmitting a 125kHz Signal
0
500kHz/div
5MHz
Figure 14. Driver Output Waveform and FFT Plot of
MAX3483E/ MAX3488E Transmitting a 125kHz Signal
______________________________________________________________________________________
11
MAX3483E/MAX3485E/MAX3486E/MAX3488E/MAX3490E/MAX3491E
_____________________Function Tables
MAX3483E/MAX3485E/MAX3486E/MAX3488E/MAX3490E/MAX3491E
3.3V-Powered, ±15kV ESD-Protected, 12Mbps and
Slew-Rate-Limited True RS-485/RS-422 Transceivers
B
1V/div
DI
2V/div
A
1V/div
Z
1V/div
RO
2V/div
Y
1V/div
20ns/div
Figure 15. MAX3485E/MAX3490E/MAX3491E Driver Propagation
Delay
20ns/div
Figure 16. MAX3485E/MAX3490E/MAX3491E Receiver
Propagation Delay Driven by External RS-485 Device
B
1V/div
DI
2V/div
A
1V/div
Z
1V/div
Y
1V/div
RO
2V/div
1µs/div
1µs/div
Figure 17. MAX3483E/MAX3488E Driver Propagation Delay
DI
5V/div
DI
5V/div
VY - VZ
2V/div
VY - VZ
2V/div
RO
5V/div
RO
5V/div
2µs/div
Figure 19. MAX3483E/MAX3488E System Differential Voltage at
125kHz Driving 4000 Feet of Cable
12
Figure 18. MAX3483E/MAX3488E Receiver Propagation Delay
2µs/div
Figure 20. MAX3485E/MAX3490E/MAX3491E System Differential
Voltage at 125kHz Driving 4000 Feet of Cable
______________________________________________________________________________________
3.3V-Powered, ±15kV ESD-Protected, 12Mbps and
Slew-Rate-Limited True RS-485/RS-422 Transceivers
±15kV ESD Protection
As with all Maxim devices, ESD-protection structures are
incorporated on all pins to protect against electrostatic
discharges encountered during handling and assembly.
The driver outputs and receiver inputs of the MAX3483E
family of devices have extra protection against static
electricity. Maxim’s engineers have developed state-ofthe-art structures to protect these pins against ESD of
±15kV without damage. The ESD structures withstand
high ESD in all states: normal operation, shutdown, and
powered down. After an ESD event, Maxim’s E versions
keep working without latchup or damage.
ESD protection can be tested in various ways; the
transmitter outputs and receiver inputs of this product
family are characterized for protection to the following
limits:
1) ±15kV using the Human Body Model
Propagation Delay
Figures 15–18 show the typical propagation delays. Skew
time is simply the difference between the low-to-high and
high-to-low propagation delay. Small driver/receiver
skew times help maintain a symmetrical mark-space
ratio (50% duty cycle).
The receiver skew time, |tPRLH - tPRHL|, is under 10ns
(20ns for the MAX3483E/MAX3488E). The driver skew
times are 8ns for the MAX3485E/MAX3490E/MAX3491E,
12ns for the MAX3486E, and typically under 50ns for the
MAX3483E/MAX3488E.
Line Length vs. Data Rate
The RS-485/RS-422 standard covers line lengths up to
4000 feet. For line lengths greater than 4000 feet, see
Figure 21 for an example of a line repeater.
Figures 19 and 20 show the system differential voltage
for parts driving 4000 feet of 26AWG twisted-pair wire
at 125kHz into 120Ω loads.
For faster data rate transmission, please consult the factory.
MAX3488E
MAX3490E
MAX3491E
A
RO
RE
DE
R
120Ω
B
DATA IN
Z
DI
D
120Ω
Y
DATA OUT
NOTE: RE AND DE ON MAX3491E ONLY.
Figure 21. Line Repeater for MAX3488E/MAX3490E/MAX3491E
2) ±8kV using the Contact-Discharge method specified
in IEC 1000-4-2
3) ±15kV using IEC 1000-4-2’s Air-Gap method.
ESD Test Conditions
ESD performance depends on a variety of conditions.
Contact Maxim for a reliability report that documents
test setup, test methodology, and test results.
Human Body Model
Figure 22a shows the Human Body Model and Figure
22b shows the current waveform it generates when discharged into a low impedance. This model consists of
a 100pF capacitor charged to the ESD voltage of interest, which is then discharged into the test device
through a 1.5kΩ resistor.
IEC 1000-4-2
The IEC 1000-4-2 standard covers ESD testing and
performance of finished equipment; it does not specifically refer to integrated circuits. The MAX3483E family
of devices helps you design equipment that meets
Level 4 (the highest level) of IEC 1000-4-2, without the
need for additional ESD-protection components.
The major difference between tests done using the
Human Body Model and IEC 1000-4-2 is higher peak
current in IEC 1000-4-2, because series resistance is
lower in the IEC 1000-4-2 model. Hence, the ESD withstand voltage measured to IEC 1000-4-2 is generally
lower than that measured using the Human Body
Model. Figure 23a shows the IEC 1000-4-2 model, and
Figure 23b shows the current waveform for the ±8kV
IEC 1000-4-2, Level 4 ESD contact-discharge test.
______________________________________________________________________________________
13
MAX3483E/MAX3485E/MAX3486E/MAX3488E/MAX3490E/MAX3491E
Driver-Output Protection
Excessive output current and power dissipation caused
by faults or by bus contention are prevented by two
mechanisms. A foldback current limit on the output stage
provides immediate protection against short circuits over
the whole common-mode voltage range (see Typical
Operating Characteristics). In addition, a thermal shutdown circuit forces the driver outputs into a high-impedance state if the die temperature rises excessively.
RC
1M
CHARGE-CURRENT
LIMIT RESISTOR
RD
1500Ω
IP 100%
90%
DISCHARGE
RESISTANCE
Ir
PEAK-TO-PEAK RINGING
(NOT DRAWN TO SCALE)
AMPERES
HIGHVOLTAGE
DC
SOURCE
Cs
100pF
STORAGE
CAPACITOR
DEVICE
UNDER
TEST
36.8%
10%
0
0
tDL
CURRENT WAVEFORM
Figure 22b. Human Body Current Waveform
Figure 22a. Human Body ESD Test Model
RC
50M to 100M
TIME
tRL
RD
330Ω
I
100%
CHARGE-CURRENT
LIMIT RESISTOR
HIGHVOLTAGE
DC
SOURCE
Cs
150pF
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
90%
DEVICE
UNDER
TEST
I PEAK
MAX3483E/MAX3485E/MAX3486E/MAX3488E/MAX3490E/MAX3491E
3.3V-Powered, ±15kV ESD-Protected, 12Mbps and
Slew-Rate-Limited True RS-485/RS-422 Transceivers
10%
Figure 23a. IEC 1000-4-2 ESD Test Model
t r = 0.7ns to 1ns
t
30ns
60ns
Figure 23b. IEC 1000-4-2 ESD Generator Current Waveform
The air-gap test involves approaching the device with a
charged probe. The contact-discharge method connects
the probe to the device before the probe is energized.
Machine Model
The Machine Model for ESD tests all pins using a
200pF storage capacitor and zero discharge resistance. Its objective is to emulate the stress caused
when I/O pins are contacted by handling equipment
during test and assembly. Of course, all pins require
this protection, not just RS-485 inputs and outputs.
14
Typical Applications
The MAX3483E/MAX3485E/MAX3486E/MAX3488E/
MAX3490E/MAX3491E transceivers are designed for
bidirectional data communications on multipoint bus
transmission lines. Figures 24 and 25 show typical network applications circuits. These parts can also be
used as line repeaters, with cable lengths longer than
4000 feet, as shown in Figure 21.
To minimize reflections, the line should be terminated at
both ends in its characteristic impedance, and stub
lengths off the main line should be kept as short as
possible. The slew-rate-limited MAX3483E/MAX3488E
and the partially slew-rate-limited MAX3486E are more
tolerant of imperfect termination.
______________________________________________________________________________________
3.3V-Powered, ±15kV ESD-Protected, 12Mbps and
Slew-Rate-Limited True RS-485/RS-422 Transceivers
DI
MAX3483E/MAX3485E/MAX3486E/MAX3488E/MAX3490E/MAX3491E
120Ω
120Ω
DE
B
B
D
D
DI
DE
B
A
A
B
A
A
R
R
RO
RE
RO
RE
R
R
D
D
MAX3483E
MAX3485E
MAX3486E
DE
DI
RO RE
DI
RO RE
DE
Figure 24. MAX3483E/MAX3485E/MAX3486E Typical RS-485 Network
A
R
RO
RE
Y
120Ω
120Ω
D
B
Z
Z
B
DE
DI
DI
DE
120Ω
D
Y
120Ω
Z
Y
B
A
Y
Z
R
A
DE RE RO
A
R
D
D
DI
B
R
RE
RO
DI
MAX3488E
MAX3490E
MAX3491E
DE RE RO
NOTE: RE AND DE ON MAX3491E ONLY.
Figure 25. MAX3488E/MAX3490E/MAX3491E Full-Duplex RS-485 Network
______________________________________________________________________________________
15
MAX3483E/MAX3485E/MAX3486E/MAX3488E/MAX3490E/MAX3491E
3.3V-Powered, ±15kV ESD-Protected, 12Mbps and
Slew-Rate-Limited True RS-485/RS-422 Transceivers
Ordering Information (continued)
PART
TEMP. RANGE
MAX3486ECSA
0°C to +70°C
8 SO
PIN-PACKAGE
MAX3486ECPA
0°C to +70°C
8 Plastic DIP
MAX3486EESA
MAX3486EEPA
MAX3488ECSA
-40°C to +85°C
-40°C to +85°C
0°C to +70°C
8 SO
8 Plastic DIP
8 SO
MAX3488ECPA
0°C to +70°C
8 Plastic DIP
MAX3488EESA
MAX3488EEPA
MAX3490ECSA
-40°C to +85°C
-40°C to +85°C
0°C to +70°C
8 SO
8 Plastic DIP
8 SO
MAX3490ECPA
0°C to +70°C
8 Plastic DIP
MAX3490EESA
MAX3490EEPA
MAX3491ECSD
-40°C to +85°C
-40°C to +85°C
0°C to +70°C
8 SO
8 Plastic DIP
14 SO
MAX3491ECPD
0°C to +70°C
14 Plastic DIP
MAX3491EESD
MAX3491EEPD
-40°C to +85°C
-40°C to +85°C
14 SO
14 Plastic DIP
Chip Information
TRANSISTOR COUNT: 761
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
16 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 1999 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
Similar pages