EPCOS B32621-A472 Metallized polypropylene film capacitors (mkp) plastic case Datasheet

Metallized Polypropylene Film Capacitors (MKP)
B 32 620
Plastic Case
B 32 621
MKP stacked-film capacitors
Smallest possible dimensions
Construction
■
■
■
■
Dielectric: polypropylene
Stacked-film technology
Plastic case (UL 94 V-0)
Epoxy resin sealing
Features
■
■
■
■
Very high pulse strength
Very good self-healing properties
Smallest possible dimensions
High contact reliability
Dimensions in mm
Lead spacing
± 0,4
Typical applications
■
■
■
■
7,5
Energy-saving lamps
TV S-correction
High pulse load applications
AC applications
10
Diameter d1
Type
0,5
B 32 620
0,51)/0,6
B 32 621
1) 0,5 mm for capacitor width b = 4 mm
Terminals
■ Parallel wire leads, tinned
■ Also available with (3,2 ± 0,3) mm lead length
Marking
Manufacturer’s logo,
lot number, style and type (P621) for lead spacing 10 mm,
style (MKP) for lead spacing 7,5 mm,
rated capacitance (coded),
capacitance tolerance (code letter),
rated dc voltage,
date of manufacture (coded)
Delivery mode
Bulk (untaped)
Taped (Ammo pack or reel)
For notes on taping, refer to chapter “Taping and packing”, page 274.
117 12/00
MKP
B 32 620
B 32 621
Overview of available types
10 mm
119
121
118 12/00
630 Vdc
400 Vac
400 Vdc
200 Vac
250 Vdc
140 Vac
160 Vdc
90 Vac
250 Vdc
140 Vac
160 Vdc
90 Vac
400 Vdc
200 Vac
1000 Vdc
600 Vac
B 32 621
Page
0,47 nF
0,68 nF
1,0 nF
1,5 nF
2,2 nF
3,3 nF
4,7 nF
6,8 nF
10 nF
15 nF
22 nF
33 nF
47 nF
68 nF
0,10 µF
0,15 µF
0,22 µF
1000 Vdc
500 Vac
B 32 620
630 Vdc
400 Vac
Type
1000 Vdc
500 Vac
Lead spacing 7,5 mm
B 32 620
MKP
7,5
Ordering codes and packing units, lead spacing 7,5 mm
VR
(Vrms
f ≤ 1 kHz)
CR
160 Vdc
(90 Vac)
22 nF
33 nF
47 nF
68 nF
0,10 µF
0,15 µF
22 nF
33 nF
47 nF
68 nF
0,10 µF
6,8 nF
10 nF
15 nF
22 nF
33 nF
1,5 nF
2,2 nF
3,3 nF
4,7 nF
6,8 nF
10 nF
15 nF
250 Vdc
(140 Vac)
400 Vdc
(200 Vac)
630 Vdc
(400 Vac)
Maximum
dimensions
b × h × l (mm)
Ordering code1)
Packing units (pcs)
3,0 × 8,0 × 10,0
4,0 × 8,5 × 10,0
4,0 × 8,5 × 10,0
5,0 × 10,5 × 10,0
5,0 × 10,5 × 10,0
6,0 × 12,0 × 10,3
4,0 × 8,5 × 10,0
4,0 × 8,5 × 10,0
5,0 × 10,5 × 10,0
5,0 × 10,5 × 10,0
6,0 × 12,0 × 10,3
4,0 × 8,5 × 10,0
4,0 × 8,5 × 10,0
5,0 × 10,5 × 10,0
5,0 × 10,5 × 10,0
6,0 × 12,0 × 10,3
4,0 × 8,5 × 10,0
4,0 × 8,5 × 10,0
4,0 × 8,5 × 10,0
4,0 × 8,5 × 10,0
5,0 × 10,5 × 10,0
5,0 × 10,5 × 10,0
6,0 × 12,0 × 10,3
B32620-A5223-+***
B32620-A5333-+***
B32620-A5473-+***
B32620-A5683-+***
B32620-A5104-+***
B32620-A5154-+***
B32620-A3223-+***
B32620-A3333-+***
B32620-A3473-+***
B32620-A3683-+***
B32620-A3104-+***
B32620-A4682-+***
B32620-A4103-+***
B32620-A4153-+***
B32620-A4223-+***
B32620-A4333-+***
B32620-A6152-+***
B32620-A6222-+***
B32620-A6332-+***
B32620-A6472-+***
B32620-A6682-+***
B32620-A6103-+***
B32620-A6153-+***
Ammo
pack
2600
2000
2000
1600
1600
1300
2000
2000
1600
1600
1300
2000
2000
1600
1600
1300
2000
2000
2000
2000
1600
1600
1300
Reel
Untaped
2400
1800
1800
1400
1400
1100
1800
1800
1400
1400
1100
1800
1800
1400
1400
1100
1800
1800
1800
1800
1400
1400
1100
2000
1500
1500
1000
1000
750
1500
1500
1000
1000
750
1500
1500
1000
1000
750
1500
1500
1500
1500
1000
1000
750
Capacitance tolerance: ± 20 % =ˆ M, ± 10 % =ˆ K, ± 5 % =ˆ J
1) +
Code letter for capacitance tolerance
*** Code number for packing: Ammo pack = 289, reel = 189
The ordering code for untaped components ends after the tolerance code letter.
For capacitors with 3,2 mm lead length, append code number “3” to the tolerance code, e.g.: B32620-A5104-K3
119 12/00
MKP
B 32 620
7,5
Ordering codes and packing units, lead spacing 7,5 mm
VR
(Vrms
f ≤ 1 kHz)
CR
1000 Vdc
(500 Vac)
1,5 nF
2,2 nF
3,3 nF
4,7 nF
6,8 nF
470 pF
680 pF
1,0 nF
1,5 nF
2,2 nF
3,3 nF
4,7 nF
1000 Vdc
(600 Vac)
Maximum
dimensions
b × h × l (mm)
Ordering code1)
Packing units (pcs)
4,0 × 8,5 × 10,0
4,0 × 8,5 × 10,0
5,0 × 10,5 × 10,0
5,0 × 10,5 × 10,0
6,0 × 12,0 × 10,3
4,0 × 8,5 × 10,0
5,0 × 10,5 × 10,0
5,0 × 10,5 × 10,0
5,0 × 10,5 × 10,0
5,0 × 10,5 × 10,0
5,0 × 10,5 × 10,0
6,0 × 12,0 × 10,3
B32620-A152-+***
B32620-A222-+***
B32620-A332-+***
B32620-A472-+***
B32620-A682-+***
B32620-J471-+***
B32620-J681-+***
B32620-J102-+***
B32620-J152-+***
B32620-J222-+***
B32620-J332-+***
B32620-J472-+***
Ammo
pack
2000
2000
1600
1600
1300
2000
1600
1600
1600
1600
1600
1300
Reel
Untaped
1800
1800
1400
1400
1100
1800
1400
1400
1400
1400
1400
1100
1500
1500
1000
1000
750
1500
1000
1000
1000
1000
1000
750
Capacitance tolerance: ± 20 % =ˆ M, ± 10 % =ˆ K, ± 5 % =ˆ J
1) +
Code letter for capacitance tolerance
*** Code number for packing: Ammo pack = 289, reel = 189
The ordering code for untaped components ends after the tolerance code letter.
For capacitors with 3,2 mm lead length, append code number “3” to the tolerance code, e.g.: B32620-A152-K3
120 12/00
B 32 621
MKP
10
Ordering codes and packing units, lead spacing 10 mm
VR
(Vrms
f ≤ 1 kHz)
CR
160 Vdc
(90 Vac)
47 nF
68 nF
0,10 µF
0,15 µF
0,22 µF
2,2 nF
3,3 nF
4,7 nF
6,8 nF
10 nF
15 nF
22 nF
33 nF
47 nF
68 nF
0,10 µF
10 nF
15 nF
22 nF
33 nF
47 nF
2,2 nF
3,3 nF
4,7 nF
6,8 nF
10 nF
15 nF
22 nF
33 nF
2,2 nF
3,3 nF
4,7 nF
6,8 nF
10 nF
250 Vdc
(140 Vac)
400 Vdc
(200 Vac)
630 Vdc
(400 Vac)
1000 Vdc
(500 Vac)
Maximum
dimensions
b × h × l (mm)
Ordering code1)
Packing units (pcs)
4,0 × 7,0 × 13,0
4,0 × 9,0 × 13,0
5,0 × 11,0 × 13,0
5,0 × 11,0 × 13,0
6,0 × 12,0 × 13,0
4,0 × 7,0 × 13,0
4,0 × 9,0 × 13,0
4,0 × 9,0 × 13,0
4,0 × 9,0 × 13,0
4,0 × 9,0 × 13,0
4,0 × 9,0 × 13,0
4,0 × 9,0 × 13,0
4,0 × 9,0 × 13,0
4,0 × 9,0 × 13,0
5,0 × 11,0 × 13,0
6,0 × 12,0 × 13,0
4,0 × 9,0 × 13,0
4,0 × 9,0 × 13,0
5,0 × 11,0 × 13,0
5,0 × 11,0 × 13,0
6,0 × 12,0 × 13,0
4,0 × 7,0 × 13,0
4,0 × 9,0 × 13,0
4,0 × 9,0 × 13,0
4,0 × 9,0 × 13,0
4,0 × 9,0 × 13,0
5,0 × 11,0 × 13,0
6,0 × 12,0 × 13,0
6,0 × 12,0 × 13,0
4,0 × 7,0 × 13,0
4,0 × 9,0 × 13,0
4,0 × 9,0 × 13,0
5,0 × 11,0 × 13,0
6,0 × 12,0 × 13,0
B32621-A5473-+***
B32621-A5683-+***
B32621-A5104-+***
B32621-A5154-+***
B32621-A5224-+***
B32621-A3222-+***
B32621-A3332-+***
B32621-A3472-+***
B32621-A3682-+***
B32621-A3103-+***
B32621-A3153-+***
B32621-A3223-+***
B32621-A3333-+***
B32621-A3473-+***
B32621-A3683-+***
B32621-A3104-+***
B32621-A4103-+***
B32621-A4153-+***
B32621-A4223-+***
B32621-A4333-+***
B32621-A4473-+***
B32621-A6222-+***
B32621-A6332-+***
B32621-A6472-+***
B32621-A6682-+***
B32621-A6103-+***
B32621-A6153-+***
B32621-A6223-+***
B32621-A6333-+***
B32621-A222-+***
B32621-A332-+***
B32621-A472-+***
B32621-A682-+***
B32621-A103-+***
Ammo
pack
1000
1000
830
830
680
1000
1000
1000
1000
1000
1000
1000
1000
1000
830
680
1000
1000
830
830
680
1000
1000
1000
1000
1000
830
680
680
1000
1000
1000
830
680
Reel
Untaped
1700
1700
1300
1300
1100
1700
1700
1700
1700
1700
1700
1700
1700
1700
1300
1100
1700
1700
1300
1300
1100
1700
1700
1700
1700
1700
1300
1100
1100
1700
1700
1700
1300
1100
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
Capacitance tolerance: ± 20 % =ˆ M, ± 10 % =ˆ K, ± 5 % =ˆ J
1) +
Code letter for capacitance tolerance
*** Code number for packing: Ammo pack = 289, reel = 189
The ordering code for untaped components ends after the tolerance code letter.
For capacitors with 3,2 mm lead length, append code number “3” to the tolerance code, e.g.: B32621-A5473-K3
121 12/00
MKP
B 32 620
B 32 621
Technical data
Climatic category
in accordance with IEC 60068-1
55/100/56
Lower category temperature Tmin
Upper category temperature Tmax
− 55 °C
+ 100 °C
Damp heat test
56 days/40 °C/93 % relative humidity
Limit values after damp
heat test
Capacitance change |∆C/C|
≤3%
Dissipation factor change ∆ tan δ ≤ 0,5 ⋅ 10−3 (at 1 kHz)
≤ 1,0 ⋅ 10−3 (at 10 kHz)
Insulation resistance Ris
≥ 50 % of minimum
as-delivered values
Reliability:
Reference conditions
Failure rate
0,5 ⋅ V R; 40 °C
1 ⋅ 10−9/h = 1 fit
For a conversion table for other operating conditions and temperatures, refer to chapter “Quality assurance”, page 327.
Service life
Failure criteria:
Total failure
Failure due to variation
of parameters
200 000 h
Short circuit or open circuit
Capacitance change |∆C/C|
Dissipation factor tan δ
Insulation resistance Ris
> ±10 %
4 ⋅ upper limit values
< 1500 MΩ
DC test voltage
1,6 ⋅ V R, 2 s
Category voltage VC
Operation with dc voltage or
ac voltage Vrms up to 1 kHz
T ≤ 85 °C: VC = 1,0 ⋅ V R or 1,0 ⋅ V rms
T = 100 °C: VC = 0,7 ⋅ V R or 0,7 ⋅ V rms
Dissipation factor tan δ (in 10−3)
at 20 °C
(upper limit values)
Insulation resistance R is
or time constant τ = CR ⋅ Ris
at 20 °C, rel. humidity ≤ 65 %
(minimum as-delivered values)
at
1 kHz
10 kHz
100 kHz
CR ≤ 0,1 µF
0,1 µF < CR ≤ 0,22 µF
–
–
4,0
1,0
1,5
–
100 GΩ
122 12/00
B 32 620
MKP
B 32 621
Impedance Z
versus
frequency f
(typical values)
KMK0680-7
10 4
mΩ
Z
10 3
5
F
7n
0,4
nF
1,5,2 nF
2
10 2
10
5 10 5
5 10 6
nF
10 1
10 4
nF
33
F
0µ
0,1 2 µF
0,2
5
5 10 7
Hz 10 8
f
Pulse handling capability
Maximum permissible voltage change per unit of time for non-sinusoidal voltages
(pulse, sawtooth)
VR
Max. rate of voltage rise V pp/τ in V/µs (for V pp = V R)
Lead spacing
7,5 mm
10 mm
160 Vdc
750
600
250 Vdc
1200
900
400 Vdc
1500
1050
630 Vdc
2700
1800
1000 Vdc (500 Vac)
3200
2400
1000 Vdc (600 Vac)
4000
−
For V pp < V R , the permissible voltage rise rate value V pp/τ may be multiplied by the factor V R/V pp.
Also refer to the calculation example in chapter “General technical information”, page 302.
VR
Pulse characteristic k0 in V2/µs (forVpp ≤ V R)
Lead spacing
7,5 mm
10 mm
160 Vdc
240 000
190 000
250 Vdc
600 000
450 000
400 Vdc
1 200 000
840 000
630 Vdc
3 400 000
2 250 000
1000 Vdc (500 Vac)
6 400 000
4 800 000
1000 Vdc (600 Vac)
8 000 000
−
123 12/00
MKP
B 32 620
7,5
Permissible ac voltage V rms versus frequency f
Lead spacing 7,5 mm
160 Vdc / 90 Vac
250 Vdc / 140 Vac
KMK0744-H
1000
Vac
Vrms
Vrms 500
500
100
100
50
50
22 nF
0,1 µF
0,15 µF
10 2
10
10 3
10 4
10 5
22 nF
0,10 µF
10 3
10 4
10 5
Hz 10 6
f
630 Vdc / 400 Vac
KMK0554-C
1000
Vac
KMK0553-4
1000
Vac
Vrms
500
500
100
100
6,8 nF
15 nF
33 nF
50
10
10 2
10
10 2
Hz 10 6
f
400 Vdc / 200 Vac
Vrms
KMK0550-E
1000
Vac
10 3
10 4
1,5 nF
3,3 nF
6,8 nF
15 nF
50
10 5
Hz 10 6
f
10
10 2
124 12/00
10 3
10 4
10 5
Hz 10 6
f
B 32 620
MKP
7,5
Permissible ac voltage V rms versus frequency f
Lead spacing 7,5 mm
1000 Vdc/ 500 Vac
1000 Vdc/ 600 Vac
KMK0560-L
1000
Vac
Vrms
Vrms
500
KMK0651-T
1000
Vac
500
0,47 nF
1,0 nF
2,2 nF
4,7 nF
1,5 nF
6,8 nF
100
100
50
50
10
10 2
10 3
10 4
10 5
Hz 10 6
f
10
10 2
125 12/00
10 3
10 4
10 5
Hz 10 6
f
MKP
B 32 621
10
Permissible ac voltage V rms versus frequency f
Lead spacing 10 mm
160 Vdc / 90 Vac
Vrms
250 Vdc / 140 Vac
KMK0715-4
400
Vac
200
Vrms
100
60
40
20
10
100
60
40
folgt
fol
20
47 nF
0,10 µF
0,22 µF
10
6
4
6
4
2
2
1 2
10
10 3
10 4
10 5
KMK0552-V
10 3
10 4
10 5
Hz 10 6
f
KMK0703-F
1000
Vac
Vrms
500
500
100
100
10
10 2
2,2 nF
15 nF
0,10 µF
630 Vdc / 400 Vac
1000
Vac
50
1 2
10
Hz 10 6
f
400 Vdc / 200 Vac
Vrms
KMK0716-C
400
Vac
200
10 nF
47 nF
10 3
50
10 4
10 5
Hz 10 6
f
10
10 2
126 12/00
2,2 nF
15 nF
33 nF
10 3
10 4
10 5
Hz 10 6
f
B 32 621
MKP
10
Permissible ac voltage V rms versus frequency f
Lead spacing 10 mm
1000 Vdc / 500 Vac
KMK0551-M
1000
Vac
V
ac
Vrms
500
100
50
10
10 2
2,2 nF
10 nF
10 3
10 4
10 5
Hz 10 6
f
127 12/00
MKP
B 32 620
B 32 621
Sinus-wave application, lighting
Permissible voltage and current / waveform
Vpp
V0-p
t = 10 ... 63,5 µs
Ipp
KMK0721-D
128 12/00
B 32 620
MKP
7,5
Sinus-wave application, lighting
Permissible current Ipp versus rated capacaitance C R
Lead spacing 7,5 mm
160 Vdc/90 Vac
250 Vdc/140 Vac
KMK0681-F
0,4
A pp
100 kHz
I pp
KMK0640-D
1,6
A pp
I pp 1,4
100 kHz
1,2
0,3
0,25
1,0
50 kHz
50 kHz
0,2
0,8
0,15
0,6
0,1
0,4
0,05
0,2
0
0
50
100
0
nF 150
C
400 Vdc/200 Vac
0
20
40
60
nF
C
80
630 Vdc/400 Vac
KMK0641-L
0,8
A pp
I pp 0,7
KMK0642-U
0,6
A pp
I pp
0,5
100 kHz
0,6
100 kHz
0,4
0,5
50 kHz
0,4
0,3
50 kHz
0,3
0,2
0,2
0,1
0,1
0
0
10
20
30
nF
C
40
0
0
129 12/00
5
10
15
nF
C
20
B 32 620
MKP
B 32 621
7,5
10
Sinus-wave application, lighting
Permissible current Ipp versus rated capacaitance C R
Lead spacing 7,5 mm
1000 Vdc/500 Vac
1000 Vdc/600 Vac
KMK0643-3
0,3
A pp
I pp
KMK0644-B
0,4
A pp
I pp
100 kHz
100 kHz
0,3
0,2
0,25
50 kHz
50 kHz
0,15
0,2
0,15
0,1
0,1
0,05
0,05
0
1
2
3
4
nF
C
0
5
1
2
3
4
nF
C
5
Lead spacing 10 mm
160 Vdc/90 Vac
250 Vdc/140 Vac
KMK0653-A
0,8
A pp
KMK0654-I
0,6
A pp
I pp 0,7
I pp
100 kHz
100 kHz
0,5
0,6
50 kHz
0,4
0,5
50 kHz
0,4
0,3
0,3
0,2
0,2
0,1
0,1
0
0
50
100
150
200 nF 250
C
0
0
50
100
nF
150
C
130 12/00
B 32 621
MKP
10
Sinus-wave application, lighting
Permissible current Ipp versus rated capacaitance C R
Lead spacing 10 mm
400 Vdc/200 Vac
630 Vdc/400 Vac
KMK0645-J
1,4
A pp
KMK0655-F
0,4
A pp
I pp
I pp 1,2
100 kHz
0,3
1,0
100 kHz
50 kHz
0,8
0,2
0,6
50 kHz
0,4
0,1
0,2
0
0
10
20
30
40 nF 50
C
0
0
I pp
KMK0646-S
100 kHz
0,5
50 kHz
0,4
0,3
0,2
0,1
0
0
2
4
6
8
20
nF
30
C
1000 Vdc/500 Vac
0,6
A pp
10
10 nF 12
C
131 12/00
Herausgegeben von EPCOS AG
Marketing Kommunikation, Postfach 80 17 09, 81617 München, DEUTSCHLAND
 EPCOS AG 2000. Alle Rechte vorbehalten. Vervielfältigung, Veröffentlichung, Verbreitung und
Verwertung dieser Broschüre und ihres Inhalts ohne ausdrückliche Genehmigung der EPCOS AG
nicht gestattet.
Mit den Angaben in dieser Broschüre werden die Bauelemente spezifiziert, keine Eigenschaften
zugesichert. Bestellungen unterliegen den vom ZVEI empfohlenen Allgemeinen Lieferbedingungen
für Erzeugnisse und Leistungen der Elektroindustrie, soweit nichts anderes vereinbart wird.
Diese Broschüre ersetzt die vorige Ausgabe.
Fragen über Technik, Preise und Liefermöglichkeiten richten Sie bitte an den Ihnen nächstgelegenen Vertrieb der EPCOS AG oder an unsere Vertriebsgesellschaften im Ausland.
Bauelemente können aufgrund technischer Erfordernisse Gefahrstoffe enthalten. Auskünfte
darüber bitten wir unter Angabe des betreffenden Typs ebenfalls über die zuständige Vertriebsgesellschaft einzuholen.
Published by EPCOS AG
Marketing Communications, P.O. Box 80 17 09, 81617 Munich, GERMANY
 EPCOS AG 2000. All Rights Reserved. Reproduction, publication and dissemination of this brochure and the information contained therein without EPCOS’ prior express consent is prohibited.
The information contained in this brochure describes the type of component and shall not be considered as guaranteed characteristics. Purchase orders are subject to the General Conditions for
the Supply of Products and Services of the Electrical and Electronics Industry recommended by the
ZVEI (German Electrical and Electronic Manufacturers’ Association), unless otherwise agreed.
This brochure replaces the previous edition.
For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or
the international Representatives.
Due to technical requirements components may contain dangerous substances. For information on
the type in question please also contact one of our Sales Offices.
1
Similar pages