Cypress CY8C24223A-24SXI Psocâ® programmable system-on-chip Datasheet

CY8C24123A
CY8C24223A
CY8C24423A
PSoC® Programmable System-on-Chip
PSoC® Programmable System-on-Chip
Features
■
■
■
■
■
Powerful Harvard-architecture processor
❐ M8C processor speeds up to 24 MHz
❐ 8 × 8 multiply, 32-bit accumulate
❐ Low power at high speed
❐ Operating voltage: 2.4 V to 5.25 V
❐ Operating voltages down to 1.0 V using on-chip switch mode
pump (SMP)
❐ Industrial temperature range: –40 °C to +85 °C
Advanced peripherals (PSoC® blocks)
❐ Six rail-to-rail analog PSoC blocks provide:
• Up to 14-bit analog-to-digital converters (ADCs)
• Up to 9-bit digital-to-analog converters (DACs)
• Programmable gain amplifiers (PGAs)
• Programmable filters and comparators
❐ Four digital PSoC blocks provide:
• 8- to 32-bit timers and counters, 8- and 16-bit pulse-width
modulators (PWMs)
• Cyclical redundancy check (CRC) and pseudo random
sequence (PRS) modules
• Full-duplex universal asynchronous receiver transmitter
(UART)
• Multiple serial peripheral interface (SPI) masters or slaves
• Can connect to all general-purpose I/O (GPIO) pins
❐ Complex peripherals by combining blocks
■
New CY8C24x23A PSoC device
❐ Derived from the CY8C24x23 device
❐ Low power and low voltage (2.4 V)
■
Additional system resources
2
❐ I C slave, master, and multi-master to 400 kHz
❐ Watchdog and sleep timers
❐ User-configurable low-voltage detection (LVD)
❐ Integrated supervisory circuit
❐ On-chip precision voltage reference
■
Complete development tools
❐ Free development software (PSoC Designer™)
❐ Full-featured, in-circuit emulator (ICE), and programmer
❐ Full-speed emulation
❐ Complex breakpoint structure
❐ 128 KB trace memory
Logic Block Diagram
Port 2 Port 1 Port 0
PSoC CORE
System Bus
Global Digital Interconnect
SRAM
256 Bytes
Precision, programmable clocking
❐ Internal ±2.5% 24- / 48-MHz main oscillator
❐ High accuracy 24 MHz with optional 32 kHz crystal and
phase-locked loop (PLL)
❐ Optional external oscillator up to 24 MHz
❐ Internal oscillator for watchdog and sleep
Cypress Semiconductor Corporation
Document Number: 38-12028 Rev. *R
•
198 Champion Court
Global Analog Interconnect
SROM
Flash 4KB
CPU Core (M8C)
Interrupt
Controller
Sleep and
Watchdog
Multiple Clock Sources
(Includes IMO, ILO, PLL, and ECO)
DIGITAL SYSTEM
Flexible on-chip memory
❐ 4 KB flash program storage 50,000 erase/write cycles
❐ 256-bytes SRAM data storage
❐ In-system serial programming (ISSP)
❐ Partial flash updates
❐ Flexible protection modes
❐ Electronically erasable programmable read only memory
(EEPROM) emulation in flash
Programmable pin configurations
❐ 25-mA sink, 10-mA source on all GPIOs
❐ Pull-up, pull-down, high Z, strong, or open-drain drive modes
on all GPIOs
❐ Eight standard analog inputs on all GPIOs, and
four additional analog inputs with restricted routing
❐ Two 30 mA analog outputs on all GPIOs
❐ Configurable interrupt on all GPIOs
Analog
Drivers
ANALOG SYSTEM
Digital
Block
Array
Digital
Clocks
Multiply
Accum.
Decimator
Analog
Ref
Analog
Block
Array
I2C
Analog
Input
Muxing
POR and LVD
System Resets
Internal
Voltage
Ref.
Switch
Mode
Pump
SYSTEM RESOURCES
•
San Jose, CA 95134-1709
•
408-943-2600
Revised April 24, 2012
CY8C24123A
CY8C24223A
CY8C24423A
Contents
PSoC Functional Overview .............................................. 3
PSoC Core .................................................................. 3
Digital System ............................................................. 3
Analog System ............................................................ 4
Additional System Resources ..................................... 5
PSoC Device Characteristics ...................................... 5
Getting Started .................................................................. 6
Application Notes ........................................................ 6
Development Kits ........................................................ 6
Training ....................................................................... 6
CYPros Consultants .................................................... 6
Solutions Library .......................................................... 6
Technical Support ....................................................... 6
Development Tools .......................................................... 6
PSoC Designer Software Subsystems ........................ 6
Designing with PSoC Designer ....................................... 7
Select User Modules ................................................... 7
Configure User Modules .............................................. 7
Organize and Connect ................................................ 7
Generate, Verify, and Debug ....................................... 7
Pinouts .............................................................................. 8
8-Pin Part Pinout ......................................................... 8
20-Pin Part Pinout ....................................................... 9
28-Pin Part Pinout ..................................................... 10
32-Pin Part Pinout ................................................... 11
56-Pin Part Pinout ..................................................... 12
Register Reference ......................................................... 13
Register Conventions ................................................ 13
Register Mapping Tables .......................................... 13
Electrical Specifications ................................................ 16
Document Number: 38-12028 Rev. *R
Absolute Maximum Ratings ....................................... 16
Operating Temperature ............................................ 17
DC Electrical Characteristics ..................................... 17
AC Electrical Characteristics ..................................... 34
Packaging Information ................................................... 47
Packaging Dimensions .............................................. 47
Thermal Impedances ................................................ 53
Capacitance on Crystal Pins .................................... 53
Solder Reflow Specifications ..................................... 53
Development Tool Selection ......................................... 54
Software .................................................................... 54
Development Kits ...................................................... 54
Evaluation Tools ........................................................ 54
Device Programmers ................................................. 55
Accessories (Emulation and Programming) .............. 55
Ordering Information ...................................................... 56
Ordering Code Definitions ......................................... 56
Acronyms ........................................................................ 57
Acronyms Used ......................................................... 57
Reference Documents .................................................... 57
Document Conventions ................................................. 58
Units of Measure ....................................................... 58
Numeric Conventions ................................................ 58
Glossary .......................................................................... 58
Document History Page ................................................. 63
Sales, Solutions, and Legal Information ...................... 65
Worldwide Sales and Design Support ....................... 65
Products .................................................................... 65
PSoC Solutions ......................................................... 65
Page 2 of 65
CY8C24123A
CY8C24223A
CY8C24423A
PSoC Functional Overview
Digital System
The digital system consists of four digital PSoC blocks. Each
block is an 8-bit resource that may be used alone or combined
with other blocks to form 8-, 16-, 24-, and 32-bit peripherals,
which are called user module references.
Figure 1. Digital System Block Diagram
Port 1
Port 2
The PSoC architecture, shown in Figure 1, consists of four main
areas: PSoC core, digital system, analog system, and system
resources. Configurable global busing allows combining all the
device resources into a complete custom system. The PSoC
CY8C24x23A family can have up to three I/O ports that connect
to the global digital and analog interconnects, providing access
to four digital blocks and six analog blocks.
To System Bus
To Analog
System
DIGITAL SYSTEM
Digital PSoC Block Array
8
The PSoC core is a powerful engine that supports a rich feature
set. The core includes a CPU, memory, clocks, and configurable
GPIOs.
The M8C CPU core is a powerful processor with speeds up to
24 Hz, providing a four-MIPS 8-bit Harvard-architecture
microprocessor. The CPU uses an interrupt controller with
11 vectors, to simplify programming of real time embedded
events. Program execution is timed and protected using the
included sleep and watchdog timers (WDT).
Row 0
DBB00
DBB01
DCB02
4
DCB03
4
GIE[7:0]
GIO[7:0]
Global Digital
Interconnect
Row Output
Configuration
8
PSoC Core
Memory encompasses 4 KB of flash for program storage, 256
bytes of SRAM for data storage, and up to 2 KB of EEPROM
emulated using the flash. Program flash uses four protection
levels on blocks of 64 bytes, allowing customized software IP
protection.
Port 0
Digital Clocks
From Core
Row Input
Configuration
The PSoC family consists of many programmable
system-on-chips with on-chip controller devices. These devices
are designed to replace multiple traditional MCU-based system
components with a low-cost single-chip programmable device.
PSoC devices include configurable blocks of analog and digital
logic, and programmable interconnects. This architecture makes
it possible for you to create customized peripheral configurations
that match the requirements of each individual application.
Additionally, a fast CPU, flash program memory, SRAM data
memory, and configurable I/O are included in a range of
convenient pinouts and packages.
8
8
GOE[7:0]
GOO[7:0]
Digital peripheral configurations are:
■
PWMs (8- and 16-bit)
■
PWMs with dead band (8- and 16-bit)
The PSoC device incorporates flexible internal clock generators,
including a 24 MHz internal main oscillator (IMO) accurate to
2.5% over temperature and voltage. The 24 MHz IMO can also
be doubled to 48 MHz for use by the digital system. A low power
32 kHz internal low speed oscillator (ILO) is provided for the
sleep timer and WDT. If crystal accuracy is required, the ECO
(32.768 kHz external crystal oscillator) is available for use as a
real time clock (RTC) and can optionally generate a
crystal-accurate 24 MHz system clock using a PLL. The clocks,
together with programmable clock dividers (as a System
Resource), provide the flexibility to integrate almost any timing
requirement into the PSoC device.
■
Counters (8- to 32-bit)
■
Timers (8- to 32-bit)
■
UART 8-bit with selectable parity
■
SPI master and slave
■
I2C slave and multi-master (one is available as a system
resource)
■
CRC generator (8- to 32-bit)
■
IrDA
PSoC GPIOs provide connection to the CPU, digital, and analog
resources of the device. Each pin’s drive mode may be selected
from eight options, allowing great flexibility in external
interfacing. Every pin can generate a system interrupt on high
level, low level, and change from last read.
■
PRS generators (8- to 32-bit)
The digital blocks may be connected to any GPIO through a
series of global buses that can route any signal to any pin. The
buses also allow for signal multiplexing and performing logic
operations. This configurability frees your designs from the
constraints of a fixed peripheral controller.
Digital blocks are provided in rows of four, where the number of
blocks varies by PSoC device family. This gives a choice of
system resources for your application. Family resources are
shown in Table 1 on page 5.
Document Number: 38-12028 Rev. *R
Page 3 of 65
CY8C24123A
CY8C24223A
CY8C24423A
The analog system consists of six configurable blocks, each
consisting of an opamp circuit that allows the creation of complex
analog signal flows. Analog peripherals are very flexible and can
be customized to support specific application requirements.
Some of the more common PSoC analog functions (most
available as user modules) are:
■
■
ADCs (up to two, with 6- to 14-bit resolution, selectable as
incremental, delta sigma, and SAR)
Figure 2. Analog System Block Diagram
P0[7]
P0[6]
P0[5]
P0[4]
P0[3]
P0[2]
P0[1]
P0[0]
AGNDIn RefIn
Analog System
P2[3]
Filters (two and four pole band-pass, low-pass, and notch)
■
Amplifiers (up to two, with selectable gain to 48x)
■
Instrumentation amplifiers (one with selectable gain to 93x)
■
Comparators (up to two, with 16 selectable thresholds)
■
DACs (up to two, with 6 to 9-bit resolution)
■
Multiplying DACs (up to two, with 6 to 9-bit resolution)
■
High current output drivers (two with 30 mA drive as a PSoC
Core resource)
■
1.3 V reference (as a system resource)
■
DTMF dialer
P2[1]
P2[4]
P2[2]
P2[0]
Array Input Configuration
ACI0[1:0]
ACI1[1:0]
Block Array
■
Modulators
ACB00
■
Correlators
ASC10
ASD11
■
Peak detectors
ASD20
ASC21
■
Many other topologies possible
Analog blocks are arranged in a column of three, which includes
one continuous time (CT) and two switched capacitor (SC)
blocks, as shown in Figure 2
P2[6]
ACB01
Analog Reference
Interface to
Digital System
RefHi
RefLo
AGND
Reference
Generators
AGNDIn
RefIn
Bandgap
M8C Interface (Address Bus, Data Bus, Etc.)
Document Number: 38-12028 Rev. *R
Page 4 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Additional System Resources
System resources, some of which are listed in the previous
sections, provide additional capability useful to complete
systems. Additional resources include a multiplier, decimator,
switch-mode pump, low-voltage detection, and power-on-reset
(POR). Statements describing the merits of each system
resource follow:
■
Digital clock dividers provide three customizable clock
frequencies for use in applications. The clocks can be routed
to both the digital and analog systems. Additional clocks may
be generated using digital PSoC blocks as clock dividers.
■
Low-voltage detection (LVD) interrupts can signal the application of falling voltage levels, while the advanced POR circuit
eliminates the need for a system supervisor.
■
An internal 1.3 V reference provides an absolute reference for
the analog system, including ADCs and DACs.
■
An integrated switch-mode pump generates normal operating
voltages from a single 1.2 V battery cell, providing a low cost
boost converter.
■
■
A multiply accumulate (MAC) provides a fast 8-bit multiplier
with 32-bit accumulate, to assist in both general math and
digital filters.
■
The decimator provides a custom hardware filter for digital
signal processing applications including the creation of Delta
Sigma ADCs.
The I2C module provides 100- and 400-kHz communication
over two wires. slave, master, and multi-master are supported.
PSoC Device Characteristics
Depending on your PSoC device characteristics, the digital and analog systems can have 16, 8, or 4 digital blocks, and 12, 6, or 4
analog blocks. Table 1 on page 5 lists the resources available for specific PSoC device groups. The PSoC device covered by this
datasheet is highlighted in this table.
Table 1. PSoC Device Characteristics
PSoC Part
Number
Digital
I/O
CY8C29x66
up to 64
CY8C28xxx
up to 44
Digital
Rows
Digital
Blocks
Analog
Inputs
Analog
Outputs
4
16
up to 12
4
up to 3
up to 12
up to 44
up to 4
Analog
Columns
Analog
Blocks
SRAM
Size
Flash
Size
4
12
2K
32 K
up to 6
up to
12 + 4[1]
1K
16 K
CY8C27x43
up to 44
2
8
up to 12
4
4
12
256
16 K
CY8C24x94
up to 56
1
4
up to 48
2
2
6
1K
16 K
CY8C24x23A
up to 24
1
4
up to 12
2
2
6
256
4K
CY8C23x33
up to 26
1
4
up to 12
2
2
4
256
8K
CY8C22x45
up to 38
2
8
up to 38
0
4
6[1]
1K
16 K
CY8C21x45
up to 24
1
4
up to 24
0
4
6[1]
512
8K
CY8C21x34
up to 28
1
4
up to 28
0
2
4[1]
512
8K
[1]
256
4K
CY8C21x23
up to 16
1
4
up to 8
0
2
CY8C20x34
up to 28
0
0
up to 28
0
0
3[1,2]
4
512
8K
CY8C20xx6
up to 36
0
0
up to 36
0
0
3[1,2]
up to
2K
up to
32 K
Notes
1. Limited analog functionality.
2. Two analog blocks and one CapSense®.
Document Number: 38-12028 Rev. *R
Page 5 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Getting Started
For in depth information, along with detailed programming
details, see the PSoC® Technical Reference Manual.
CYPros Consultants
For up-to-date ordering, packaging, and electrical specification
information, see the latest PSoC device datasheets on the web.
Certified PSoC Consultants offer everything from technical
assistance to completed PSoC designs. To contact or become a
PSoC Consultant go to the CYPros Consultants web site.
Application Notes
Solutions Library
Cypress application notes are an excellent introduction to the
wide variety of possible PSoC designs.
Visit our growing library of solution focused designs. Here you
can find various application designs that include firmware and
hardware design files that enable you to complete your designs
quickly.
Development Kits
PSoC Development Kits are available online from and through a
growing number of regional and global distributors, which
include Arrow, Avnet, Digi-Key, Farnell, Future Electronics, and
Newark.
Training
Technical Support
Technical support – including a searchable knowledge base
articles and technical forums – is also available online. If you
cannot find an answer to your question, call our Technical
Support hotline at 1-800-541-4736.
Free PSoC technical training (on demand, webinars, and
workshops), which is available online via www.cypress.com,
covers a wide variety of topics and skill levels to assist you in
your designs.
Development Tools
PSoC Designer™ is the revolutionary integrated design
environment (IDE) that you can use to customize PSoC to meet
your specific application requirements. PSoC Designer software
accelerates system design and time to market. Develop your
applications using a library of precharacterized analog and digital
peripherals (called user modules) in a drag-and-drop design
environment. Then, customize your design by leveraging the
dynamically generated application programming interface (API)
libraries of code. Finally, debug and test your designs with the
integrated debug environment, including in-circuit emulation and
standard software debug features. PSoC Designer includes:
■
Application editor graphical user interface (GUI) for device and
user module configuration and dynamic reconfiguration
■
Extensive user module catalog
■
Integrated source-code editor (C and assembly)
■
Free C compiler with no size restrictions or time limits
■
Built-in debugger
■
In-circuit emulation
Built-in support for communication interfaces:
2
❐ Hardware and software I C slaves and masters
❐ Full-speed USB 2.0
❐ Up to four full-duplex universal asynchronous receiver/transmitters (UARTs), SPI master and slave, and wireless
PSoC Designer supports the entire library of PSoC 1 devices and
runs on Windows XP, Windows Vista, and Windows 7.
■
Document Number: 38-12028 Rev. *R
PSoC Designer Software Subsystems
Design Entry
In the chip-level view, choose a base device to work with. Then
select different onboard analog and digital components that use
the PSoC blocks, which are called user modules. Examples of
user modules are analog-to-digital converters (ADCs),
digital-to-analog converters (DACs), amplifiers, and filters.
Configure the user modules for your chosen application and
connect them to each other and to the proper pins. Then
generate your project. This prepopulates your project with APIs
and libraries that you can use to program your application.
The tool also supports easy development of multiple configurations and dynamic reconfiguration. Dynamic reconfiguration
makes it possible to change configurations at run time. In
essence, this lets you to use more than 100 percent of PSoC's
resources for an application.
Code Generation Tools
The code generation tools work seamlessly within the
PSoC Designer interface and have been tested with a full range
of debugging tools. You can develop your design in C, assembly,
or a combination of the two.
Assemblers. The assemblers allow you to merge assembly
code seamlessly with C code. Link libraries automatically use
absolute addressing or are compiled in relative mode, and linked
with other software modules to get absolute addressing.
C Language Compilers. C language compilers are available
that support the PSoC family of devices. The products allow you
to create complete C programs for the PSoC family devices. The
optimizing C compilers provide all of the features of C, tailored
to the PSoC architecture. They come complete with embedded
libraries providing port and bus operations, standard keypad and
display support, and extended math functionality.
Page 6 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Debugger
In-Circuit Emulator
PSoC Designer has a debug environment that provides
hardware in-circuit emulation, allowing you to test the program in
a physical system while providing an internal view of the PSoC
device. Debugger commands allow you to read and program and
read and write data memory, and read and write I/O registers.
You can read and write CPU registers, set and clear breakpoints,
and provide program run, halt, and step control. The debugger
also lets you to create a trace buffer of registers and memory
locations of interest.
A low-cost, high-functionality in-circuit emulator (ICE) is
available for development support. This hardware can program
single devices.
The emulator consists of a base unit that connects to the PC
using a USB port. The base unit is universal and operates with
all PSoC devices. Emulation pods for each device family are
available separately. The emulation pod takes the place of the
PSoC device in the target board and performs full-speed
(24 MHz) operation.
Online Help System
The online help system displays online, context-sensitive help.
Designed for procedural and quick reference, each functional
subsystem has its own context-sensitive help. This system also
provides tutorials and links to FAQs and an Online Support
Forum to aid the designer.
Designing with PSoC Designer
The development process for the PSoC device differs from that
of a traditional fixed-function microprocessor. The configurable
analog and digital hardware blocks give the PSoC architecture a
unique flexibility that pays dividends in managing specification
change during development and lowering inventory costs. These
configurable resources, called PSoC blocks, have the ability to
implement a wide variety of user-selectable functions. The PSoC
development process is:
1. Select user modules.
2. Configure user modules.
3. Organize and connect.
4. Generate, verify, and debug.
Select User Modules
PSoC Designer provides a library of prebuilt, pretested hardware
peripheral components called “user modules.” User modules
make selecting and implementing peripheral devices, both
analog and digital, simple.
Configure User Modules
Each user module that you select establishes the basic register
settings that implement the selected function. They also provide
parameters and properties that allow you to tailor their precise
configuration to your particular application. For example, a PWM
User Module configures one or more digital PSoC blocks, one
for each eight bits of resolution. Using these parameters, you can
establish the pulse width and duty cycle. Configure the parameters and properties to correspond to your chosen application.
Enter values directly or by selecting values from drop-down
menus. All of the user modules are documented in datasheets
that may be viewed directly in PSoC Designer or on the Cypress
website. These user module datasheets explain the internal
operation of the user module and provide performance specifications. Each datasheet describes the use of each user module
parameter, and other information that you may need to successfully implement your design.
Document Number: 38-12028 Rev. *R
Organize and Connect
Build signal chains at the chip level by interconnecting user
modules to each other and the I/O pins. Perform the selection,
configuration, and routing so that you have complete control over
all on-chip resources.
Generate, Verify, and Debug
When you are ready to test the hardware configuration or move
on to developing code for the project, perform the “Generate
Configuration Files” step. This causes PSoC Designer to
generate source code that automatically configures the device to
your specification and provides the software for the system. The
generated code provides APIs with high-level functions to control
and respond to hardware events at run time, and interrupt
service routines that you can adapt as needed.
A complete code development environment lets you to develop
and customize your applications in C, assembly language, or
both.
The last step in the development process takes place inside
PSoC Designer's Debugger (accessed by clicking the Connect
icon). PSoC Designer downloads the HEX image to the ICE
where it runs at full-speed. PSoC Designer debugging capabilities rival those of systems costing many times more. In addition
to traditional single-step, run-to-breakpoint, and watch-variable
features, the debug interface provides a large trace buffer. It lets
you to define complex breakpoint events that include monitoring
address and data bus values, memory locations, and external
signals.
Page 7 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Pinouts
This section describes, lists, and illustrates the CY8C24x23A PSoC device pins and pinout configurations. Every port pin (labeled
with a “P”) is capable of digital I/O. However, VSS, VDD, SMP, and XRES are not capable of digital I/O.
8-Pin Part Pinout
Table 2. 8-Pin PDIP and SOIC
Pin
No.
1
2
3
4
5
6
7
8
Type
Pin
Description
Digital Analog Name
I/O
I/O
P0[5]
Analog column mux input and column
output
I/O
I/O
P0[3]
Analog column mux input and column
output
I/O
P1[1]
Crystal input (XTALin), I2C serial clock
(SCL), ISSP-SCLK[3]
Power
VSS
Ground connection
I/O
P1[0]
Crystal output (XTALout), I2C serial
data (SDA), ISSP-SDATA[3]
I/O
I
P0[2]
Analog column mux input
I/O
I
P0[4]
Analog column mux input
Power
VDD
Supply voltage
Figure 3. CY8C24123A 8-Pin PSoC Device
A, IO, P0[5]
A, IO, P0[3]
I2C SCL, XTALin, P1[1]
VSS
1
VDD
8
2 PDIP 7
3 SOIC 6
P0[4], A, I
4
P1[0], XTALout, I2C SDA
5
P0[2], A, I
LEGEND: A = Analog, I = Input, and O = Output.
Note
3. These are the ISSP pins, which are not high Z at POR. See the PSoC Technical Reference Manual for details.
Document Number: 38-12028 Rev. *R
Page 8 of 65
CY8C24123A
CY8C24223A
CY8C24423A
20-Pin Part Pinout
Table 3. 20-Pin PDIP, SSOP, and SOIC
Pin
No.
1
2
3
4
5
Type
Digital Analog
I/O
I
I/O
I/O
I/O
I/O
I/O
I
Power
Pin
Name
P0[7]
P0[5]
P0[3]
P0[1]
SMP
Analog column mux input
Analog column mux input and column output
Analog column mux input and column output
Analog column mux input
SMP connection to external components
required
I2C SCL
I2C SDA
6
7
8
9
10
11
12
13
14
15
I/O
I/O
I/O
I/O
16
I/O
I
P0[0]
Active high external reset with internal
pull-down
Analog column mux input
17
I/O
I
P0[2]
Analog column mux input
18
I/O
I
P0[4]
Analog column mux input
19
I/O
P0[6]
Analog column mux input
VDD
Supply voltage
20
P1[7]
P1[5]
P1[3]
P1[1]
VSS
P1[0]
P1[2]
P1[4]
P1[6]
XRES
Description
Power
I/O
I/O
I/O
I/O
Input
I
Power
Figure 4. CY8C24223A 20-Pin PSoC Device
A, I, P0[7]
1
20
VDD
A, IO, P0[5]
2
19
P0[6], A, I
A, IO, P0[3]
3
18
A, I, P0[1]
4
PDIP
17
P0[4], A, I
P0[2], A, I
SSOP
16
P0[0], A, I
15
XRES
14
P1[6]
SMP
5
I2C SCL, P1[7]
6
I2C SDA, P1[5]
7
P1[3]
8
13
P1[4], EXTCLK
I2C SCL, XTALin, P1[1]
9
12
VSS
10
11
P1[2]
P1[0], XTALout,
I2C SDA
SOIC
XTALin, I2C SCL, ISSP-SCLK[4]
Ground connection.
XTALout, I2C SDA, ISSP-SDATA[4]
Optional external clock input (EXTCLK)
LEGEND: A = Analog, I = Input, and O = Output.
Note
4. These are the ISSP pins, which are not high Z at POR. See the PSoC Technical Reference Manual for details.
Document Number: 38-12028 Rev. *R
Page 9 of 65
CY8C24123A
CY8C24223A
CY8C24423A
28-Pin Part Pinout
Table 4. 28-Pin PDIP, SSOP, and SOIC
Pin
No.
1
2
3
4
5
6
7
8
9
Type
Digital Analog
I/O
I
I/O
I/O
I/O
I/O
I/O
I
I/O
I/O
I/O
I
I/O
I
Power
10
11
12
13
14
15
16
17
18
19
I/O
I/O
I/O
I/O
20
21
22
23
24
25
26
27
28
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
P0[7]
P0[5]
P0[3]
P0[1]
P2[7]
P2[5]
P2[3]
P2[1]
SMP
P1[7]
P1[5]
P1[3]
P1[1]
VSS
P1[0]
P1[2]
P1[4]
P1[6]
XRES
Power
I/O
I/O
I/O
I/O
Input
I
I
I
I
I
I
Power
Pin
Name
P2[0]
P2[2]
P2[4]
P2[6]
P0[0]
P0[2]
P0[4]
P0[6]
VDD
Description
Analog column mux input
Analog column mux input and column output
Analog column mux input and column output
Analog column mux input
Direct switched capacitor block input
Direct switched capacitor block input
SMP connection to external components
required
I2C SCL
I2C SDA
Figure 5. CY8C24423A 28-Pin PSoC Device
A, I, P0[7]
1
28
VDD
A, IO, P0[5]
2
27
P0[6], A, I
A, IO, P0[3]
3
26
P0[4], A, I
A, I, P0[1]
4
25
P0[2], A, I
P2[7]
5
24
P0[0], A, I
P2[5]
6
PDIP
23
P2[6], External VRef
A, I, P2[3]
7
22
P2[4], External AGND
A, I, P2[1]
8
SSOP
21
P2[2], A, I
SMP
9
20
P2[0], A, I
I2CSCL, P1[7]
10
19
XRES
I2C SDA, P1[5]
11
18
P1[6]
P1[3]
12
17
P1[4], EXTCLK
I2C SCL, XTALin, P1[1]
13
16
P1[2]
VSS
14
15
P1[0], XTALout, I2C
SDA
SOIC
XTALin, I2C SCL, ISSP-SCLK[5]
Ground connection.
XTALout, I2C SDA, ISSP-SDATA[5]
Optional EXTCLK
Active high external reset with internal
pull-down
Direct switched capacitor block input
Direct switched capacitor block input
External analog ground (AGND)
External voltage reference (VREF)
Analog column mux input
Analog column mux input
Analog column mux input
Analog column mux input
Supply voltage
LEGEND: A = Analog, I = Input, and O = Output.
Note
5. These are the ISSP pins, which are not high Z at POR. See the PSoC Technical Reference Manual for details.
Document Number: 38-12028 Rev. *R
Page 10 of 65
CY8C24123A
CY8C24223A
CY8C24423A
32-Pin Part Pinout
Table 5. 32-Pin QFN[6]
I/O
I/O
P0[3]
32
I/O
I
P0[1]
P0[3], A, IO
P0[5], A, IO
P0[7], A, I
VDD
P0[6], A, I
P0[4], A, I
NC
31
30
29
28
26
25
27
P0[1], A, I
32
P2[4], External AGND
VSS
5
20
P2[2], A, I
SMP
6
19
P2[0], A, I
I2C SCL, P1[7]
7
18
XRES
I2C SDA, P1[5]
8
17
P1[6]
(Top View)
16
31
21
QFN
15
I
I/O
4
NC
I/O
I/O
Power
P2[6], External VRef
A, I, P2[1]
EXTCLK, P1[4]
I
I
I
I
22
14
I/O
I/O
P2[0]
P2[2]
P2[4]
P2[6]
P0[0]
P0[2]
NC
P0[4]
P0[6]
VDD
P0[7]
P0[5]
Input
3
P1[2]
I
I
I/O
Optional EXTCLK
No connection. Pin must be left floating
P0[0], A, I
A, I, P2[3]
13
I/O
I/O
I/O
I/O
I/O
I/O
Power
I/O
I/O
I/O
XTALin, I2C SCL, ISSP-SCLK[7]
Ground Connection
XTALout, I2C SDA, ISSP-SDATA[7]
P0[2], A, I
23
I2C SDA, XTALout, P1[0]
19
20
21
22
23
24
25
26
27
28
29
30
I/O
I/O
24
2
12
P1[7]
P1[5]
NC
P1[3]
P1[1]
VSS
P1[0]
P1[2]
P1[4]
NC
P1[6]
XRES
1
P2[5]
11
I/O
I/O
P2[7]
I2C SCL, XTALin, P1[1]
VSS
7
8
9
10
11
12
13
14
15
16
17
18
Direct switched capacitor block input
Direct switched capacitor block input
Ground connection
SMP connection to external components
required
I2C SCL
I2C SDA
No connection. Pin must be left floating
Figure 6. CY8C24423A 32-Pin PSoC Device
9
P2[7]
P2[5]
P2[3]
P2[1]
VSS
SMP
Description
10
Pin
Name
NC
1
2
3
4
5
6
Type
Digital
Analog
I/O
I/O
I/O
I
I/O
I
Power
Power
P1[3]
Pin No.
Active high external reset with internal
pull-down
Direct switched capacitor block input
Direct switched capacitor block input
External AGND
External VREF
Analog column mux input
Analog column mux input
No connection. Pin must be left floating
Analog column mux input
Analog column mux input
Supply voltage
Analog column mux input
Analog column mux input and column
output
Analog column mux input and column
output
Analog column mux input
LEGEND: A = Analog, I = Input, and O = Output.
Notes
6. The center pad on the QFN package must be connected to ground (VSS) for best mechanical, thermal, and electrical performance. If not connected to ground, it
must be electrically floated and not connected to any other signal.
7. These are the ISSP pins, which are not high Z at POR. See the PSoC Technical Reference Manual for details.
Document Number: 38-12028 Rev. *R
Page 11 of 65
CY8C24123A
CY8C24223A
CY8C24423A
56-Pin Part Pinout
The 56-pin SSOP part is for the CY8C24000A On-Chip Debug (OCD) PSoC device.
Note This part is only used for in-circuit debugging. It is NOT available for production.
Table 6. 56-Pin SSOP OCD
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Type
Digital
Analog
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
I
I
I
OCD
OCD
Power
I
I
Pin
Name
NC
P0[7]
P0[5]
P0[3]
P0[1]
P2[7]
P2[5]
P2[3]
P2[1]
NC
NC
NC
NC
OCDE
OCDO
SMP
Description
No connection. Pin must be left floating
Analog column mux input
Analog column mux input and column output
Analog column mux input and column output
Analog column mux input
Direct switched capacitor block input
Direct switched capacitor block input
No connection. Pin must be left floating
No connection. Pin must be left floating
No connection. Pin must be left floating
No connection. Pin must be left floating
OCD even data I/O
OCD odd data output
SMP connection to required external components
No connection. Pin must be left floating
No connection. Pin must be left floating
No connection. Pin must be left floating
No connection. Pin must be left floating
No connection. Pin must be left floating
No connection. Pin must be left floating
I2C SCL
I2C SDA
No connection. Pin must be left floating
17
NC
18
NC
19
NC
20
NC
21
NC
22
NC
23
I/O
P1[7]
24
I/O
P1[5]
25
NC
26
I/O
P1[3]
27
I/O
P1[1]
XTALin, I2C SCL, ISSP-SCLK[8]
28
Power
VDD
Supply voltage
29
NC
No connection. Pin must be left floating
30
NC
No connection. Pin must be left floating
31
I/O
P1[0]
XTALout, I2C SDA, ISSP-SDATA[8]
32
I/O
P1[2]
33
I/O
P1[4]
Optional EXTCLK
34
I/O
P1[6]
35
NC
No connection. Pin must be left floating
36
NC
No connection. Pin must be left floating
37
NC
No connection. Pin must be left floating
38
NC
No connection. Pin must be left floating
39
NC
No connection. Pin must be left floating
40
NC
No connection. Pin must be left floating
41
Input
XRES
Active high external reset with internal pull-down.
42
OCD
HCLK
OCD high speed clock output.
43
OCD
CCLK
OCD CPU clock output.
44
NC
No connection. Pin must be left floating
45
NC
No connection. Pin must be left floating
46
NC
No connection. Pin must be left floating
47
NC
No connection. Pin must be left floating
48
I/O
I
P2[0]
Direct switched capacitor block input.
49
I/O
I
P2[2]
Direct switched capacitor block input.
50
I/O
P2[4]
External AGND.
51
I/O
P2[6]
External VREF.
52
I/O
I
P0[0]
Analog column mux input.
53
I/O
I
P0[2]
Analog column mux input and column output.
54
I/O
I
P0[4]
Analog column mux input and column output.
55
I/O
I
P0[6]
Analog column mux input.
56
Power
VDD
Supply voltage.
LEGEND: A = Analog, I = Input, O = Output, and OCD = On-Chip Debug.
Figure 7. CY8C24000A 56-Pin PSoC Device
NC
AI, P0[7]
AIO, P0[5]
AIO, P0[3]
AI, P0[1]
P2[7]
P2[5]
AI, P2[3]
AI, P2[1]
NC
NC
NC
NC
56
55
54
53
1
2
3
4
5
6
7
8
9
10
52
51
11
12
13
OCDE
OCDO
SMP
NC
NC
NC
NC
NC
NC
I2C SCL, P1[7]
14
15
16
17
I2C SDA, P1[5]
NC
P1[3]
SCLK, I2C SCL, XTALIn, P1[1]
VSS
24
25
26
27
28
18
19
20
21
22
23
SSOP
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
VDD
P0[6], AI
P0[4], AIO
P0[2], AIO
P0[0], AI
P2[6], External VRef
P2[4], External AGND
P2[2], AI
P2[0], AI
NC
NC
NC
NC
CCLK
HCLK
XRES
NC
NC
NC
NC
NC
NC
P1[6]
P1[4], EXTCLK
P1[2]
P1[0], XTALOut, I2C SDA, SDATA
NC
NC
Not for Production
Note
8. These are the ISSP pins, which are not high Z at POR. See the PSoC Technical Reference Manual for details.
Document Number: 38-12028 Rev. *R
Page 12 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Register Reference
This section lists the registers of the CY8C24x23A PSoC device. For detailed register information, see the PSoC Programmable
Sytem-on-Chip Reference Manual.
Register Conventions
Register Mapping Tables
Abbreviations Used
The PSoC device has a total register address space of 512
bytes. The register space is referred to as I/O space and is
divided into two banks, Bank 0 and Bank 1. The XOI bit in the
Flag register (CPU_F) determines which bank the user is
currently in. When the XOI bit is set, the user is in Bank 1.
The register conventions specific to this section are listed in the
following table.
Table 7. Abbreviations
Convention
Description
R
Read register or bit(s)
W
Write register or bit(s)
L
Logical register or bit(s)
C
Clearable register or bit(s)
#
Access is bit specific
Document Number: 38-12028 Rev. *R
Note In the following register mapping tables, blank fields are
reserved and must not be accessed.
Page 13 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Table 8. Register Map Bank 0 Table: User Space
Name
PRT0DR
PRT0IE
PRT0GS
PRT0DM2
PRT1DR
PRT1IE
PRT1GS
PRT1DM2
PRT2DR
PRT2IE
PRT2GS
PRT2DM2
DBB00DR0
DBB00DR1
DBB00DR2
DBB00CR0
DBB01DR0
DBB01DR1
DBB01DR2
DBB01CR0
DCB02DR0
DCB02DR1
DCB02DR2
DCB02CR0
DCB03DR0
DCB03DR1
DCB03DR2
DCB03CR0
Addr (0,Hex) Access
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
Name
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
#
W
RW
#
#
W
RW
#
#
W
RW
#
#
W
RW
#
AMX_IN
ARF_CR
CMP_CR0
ASY_CR
CMP_CR1
ACB00CR3
ACB00CR0
ACB00CR1
ACB00CR2
ACB01CR3
ACB01CR0
ACB01CR1
ACB01CR2
3F
Blank fields are Reserved and must not be accessed.
Document Number: 38-12028 Rev. *R
Addr (0,Hex)
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
Access
Name
ASC10CR0
ASC10CR1
ASC10CR2
ASC10CR3
ASD11CR0
ASD11CR1
ASD11CR2
ASD11CR3
ASD20CR0
ASD20CR1
ASD20CR2
ASD20CR3
ASC21CR0
ASC21CR1
ASC21CR2
ASC21CR3
RW
RW
#
#
RW
RW
RW
RW
RW
RW
RW
RW
RW
RDI0RI
RDI0SYN
RDI0IS
RDI0LT0
RDI0LT1
RDI0RO0
RDI0RO1
Addr (0,Hex)
80
81
82
83
84
85
86
87
88
89
8A
8B
8C
8D
8E
8F
90
91
92
93
94
95
96
97
98
99
9A
9B
9C
9D
9E
9F
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
AA
AB
AC
AD
AE
AF
B0
B1
B2
B3
B4
B5
B6
B7
B8
B9
BA
BB
BC
BD
BE
BF
Access
Name
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Addr (0,Hex)
CPU_SCR1
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
DD
DE
DF
E0
E1
E2
E3
E4
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
CPU_SCR0
FF
I2C_CFG
I2C_SCR
I2C_DR
I2C_MSCR
INT_CLR0
INT_CLR1
INT_CLR3
INT_MSK3
INT_MSK0
INT_MSK1
INT_VC
RES_WDT
DEC_DH
DEC_DL
DEC_CR0
DEC_CR1
MUL_X
MUL_Y
MUL_DH
MUL_DL
ACC_DR1
ACC_DR0
ACC_DR3
ACC_DR2
RW
RW
RW
RW
RW
RW
RW
CPU_F
Access
RW
#
RW
#
RW
RW
RW
RW
RW
RW
RC
W
RC
RC
RW
RW
W
W
R
R
RW
RW
RW
RW
RL
#
#
# Access is bit specific.
Page 14 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Table 0-1. Register Map Bank 1 Table: Configuration Space
Name
PRT0DM0
PRT0DM1
PRT0IC0
PRT0IC1
PRT1DM0
PRT1DM1
PRT1IC0
PRT1IC1
PRT2DM0
PRT2DM1
PRT2IC0
PRT2IC1
DBB00FN
DBB00IN
DBB00OU
DBB01FN
DBB01IN
DBB01OU
DCB02FN
DCB02IN
DCB02OU
DCB03FN
DCB03IN
DCB03OU
Addr (1,Hex)
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
Access
Name
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
CLK_CR0
CLK_CR1
ABF_CR0
AMD_CR0
AMD_CR1
ALT_CR0
RW
RW
RW
RW
RW
RW
ACB00CR3
ACB00CR0
ACB00CR1
ACB00CR2
ACB01CR3
ACB01CR0
ACB01CR1
ACB01CR2
Blank fields are Reserved and must not be accessed.
Document Number: 38-12028 Rev. *R
Addr (1,Hex)
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
Access
Name
ASC10CR0
ASC10CR1
ASC10CR2
ASC10CR3
ASD11CR0
ASD11CR1
ASD11CR2
ASD11CR3
ASD20CR0
ASD20CR1
ASD20CR2
ASD20CR3
ASC21CR0
ASC21CR1
ASC21CR2
ASC21CR3
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RDI0RI
RDI0SYN
RDI0IS
RDI0LT0
RDI0LT1
RDI0RO0
RDI0RO1
Addr (1,Hex)
80
81
82
83
84
85
86
87
88
89
8A
8B
8C
8D
8E
8F
90
91
92
93
94
95
96
97
98
99
9A
9B
9C
9D
9E
9F
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
AA
AB
AC
AD
AE
AF
B0
B1
B2
B3
B4
B5
B6
B7
B8
B9
BA
BB
BC
BD
BE
BF
Access
Name
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
GDI_O_IN
GDI_E_IN
GDI_O_OU
GDI_E_OU
OSC_GO_EN
OSC_CR4
OSC_CR3
OSC_CR0
OSC_CR1
OSC_CR2
VLT_CR
VLT_CMP
IMO_TR
ILO_TR
BDG_TR
ECO_TR
RW
RW
RW
RW
RW
RW
RW
CPU_F
CPU_SCR1
CPU_SCR0
Addr (1,Hex)
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
DD
DE
DF
E0
E1
E2
E3
E4
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
Access
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
R
W
W
RW
W
RL
#
#
# Access is bit specific.
Page 15 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Electrical Specifications
This section presents the DC and AC electrical specifications of the CY8C24x23A PSoC device. For the latest electrical specifications,
check if you have the most recent datasheet by visiting the website at http://www.cypress.com.
Specifications are valid for –40 °C  TA  85 °C and TJ  100 °C, except where noted.
Refer to Table 29 on page 34 for the electrical specifications for the IMO using SLIMO mode.
Figure 8. Voltage versus CPU Frequency
Figure 8. IMO Frequency Trim Options
5.25
SLIMO Mode = 0
5.25
SLIMO
Mode=1
4.75
Vdd Voltage
Vdd Voltage
l id g
Va ratin n
pe io
O Reg
4.75
3.60
3.00
3.00
2.40
2.40
93 kHz
3 MHz
12 MHz
SLIMO
Mode=0
SLIMO
SLIMO
Mode=1
Mode=0
SLIMO SLIMO
Mode=1 Mode=1
24 MHz
93 kHz
6 MHz
12 MHz
24 MHz
IM OFrequency
CPUFreque ncy
Absolute Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the device. User guidelines are not tested.
Table 9. Absolute Maximum Ratings
Symbol
TSTG
Description
Storage temperature
TBAKETEMP
Bake temperature
tBAKETIME
Bake time
TA
VDD
VIO
VIOZ
IMIO
ESD
LU
Ambient temperature with power applied
Supply voltage on VDD relative to VSS
DC input voltage
DC voltage applied to tri-state
Maximum current into any port pin
Electrostatic discharge voltage
Latch up current
Document Number: 38-12028 Rev. *R
Min
–55
Typ
25
Max
+100
Units
Notes
°C
Higher storage temperatures
reduce data retention time.
Recommended storage
temperature is +25 °C ± 25 °C.
Extended duration storage
temperatures above 65 °C
degrades reliability.
°C
–
125
See
package
label
–40
–0.5
VSS – 0.5
VSS – 0.5
–25
2000
–
–
See
package
label
72
Hours
–
–
–
–
–
–
–
+85
+6.0
VDD + 0.5
VDD + 0.5
+50
–
200
°C
V
V
V
mA
V
mA
Human body model ESD.
Page 16 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Operating Temperature
Table 10. Operating Temperature
Symbol
Description
TA
Ambient temperature
TJ
Junction temperature
Min
–40
–40
Typ
–
–
Max
+85
+100
Units
Notes
°C
°C
The temperature rise from ambient to
junction is package specific. See
Table 48 on page 53. You must limit
the power consumption to comply with
this requirement
DC Electrical Characteristics
DC Chip-Level Specifications
Table 11 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively. Typical parameters
are measured at 5 V, 3.3 V, and 2.7 V at 25 °C and are for design guidance only.
Table 11. DC Chip-Level Specifications
Symbol
VDD
Supply voltage
Description
Min
2.4
Typ
–
Max
5.25
IDD
Supply current
–
5
8
IDD3
Supply current
–
3.3
6.0
IDD27
Supply current
–
2
4
ISB
Sleep (mode) current with POR, LVD, sleep timer,
and WDT.[9]
–
3
6.5
ISBH
Sleep (mode) current with POR, LVD, sleep timer,
and WDT at high temperature.[9]
–
4
25
ISBXTL
Sleep (mode) current with POR, LVD, sleep timer,
WDT, and external crystal.[9]
–
4
7.5
ISBXTLH
Sleep (Mode) current with POR, LVD, sleep timer,
WDT, and external crystal at high temperature.[9]
–
5
26
VREF
Reference voltage (Bandgap)
1.28
1.30
1.32
VREF27
Reference voltage (Bandgap)
1.16
1.30
1.32
Units
Notes
V
See DC POR and LVD specifications,
Table 26 on page 32
mA Conditions are VDD = 5.0 V, TA = 25 °C,
CPU = 3 MHz, SYSCLK doubler
disabled, VC1 = 1.5 MHz,
VC2 = 93.75 kHz, VC3 = 93.75 kHz,
analog power = off
SLIMO mode = 0. IMO = 24 MHz
mA Conditions are VDD = 3.3 V, TA= 25 °C,
CPU = 3 MHz, SYSCLK doubler
disabled, VC1 = 1.5 MHz,
VC2 = 93.75 kHz, VC3 = 93.75 kHz,
analog power = off. SLIMO mode = 0.
IMO = 24 MHz
mA Conditions are VDD = 2.7 V, TA = 25 °C,
CPU = 0.75 MHz, SYSCLK doubler
disabled, VC1 = 0.375 MHz,
VC2 = 23.44 kHz, VC3 = 0.09 kHz,
analog power = off. SLIMO mode = 1.
IMO = 6 MHz
µA
Conditions are with internal slow speed
oscillator, VDD = 3.3 V, –40 °C  TA 
55 °C, analog power = off
µA
Conditions are with internal slow speed
oscillator, VDD = 3.3 V, 55 °C < TA 
85 °C, analog power = off
µA
Conditions are with properly loaded,
1 µW max, 32.768 kHz crystal.
VDD = 3.3 V, –40 °C  TA  55 °C, analog
power = off
µA
Conditions are with properly loaded,
1µW max, 32.768 kHz crystal.
VDD = 3.3 V, 55 °C < TA  85 °C, analog
power = off
V
Trimmed for appropriate VDD.
VDD > 3.0 V
V
Trimmed for appropriate VDD.
VDD = 2.4 V to 3.0 V
Note
9. Standby current includes all functions (POR, LVD, WDT, sleep time) needed for reliable system operation. This must be compared with devices that have similar
functions enabled.
Document Number: 38-12028 Rev. *R
Page 17 of 65
CY8C24123A
CY8C24223A
CY8C24423A
DC GPIO Specifications
The following tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to
5.25 V and –40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively.
Typical parameters are measured at 5 V, 3.3 V, and 2.7 V at 25 °C and are for design guidance only.
Table 12. 5-V and 3.3-V DC GPIO Specifications
Symbol
Description
Pull-up resistor
RPU
Pull-down resistor
RPD
High output level
VOH
Min
4
4
VDD – 1.0
Typ
5.6
5.6
–
Max
8
8
–
VOL
Low output level
–
–
0.75
IOH
High level source current
10
–
–
IOL
Low level sink current
25
–
–
VIL
VIH
VH
IIL
CIN
Input low level
Input high level
Input hysterisis
Input leakage (absolute value)
Capacitive load on pins as input
–
2.1
–
–
–
–
–
60
1
3.5
0.8
COUT
Capacitive load on pins as output
–
3.5
10
Min
4
4
VDD – 0.4
Typ
5.6
5.6
–
Max
8
8
–
–
–
10
Units
Notes
k
k
V
IOH = 10 mA, VDD = 4.75 to 5.25 V
(maximum 40 mA on even port pins
(for example, P0[2], P1[4]), maximum
40 mA on odd port pins (for example,
P0[3], P1[5])). 80 mA maximum
combined IOH budget.
V
IOL = 25 mA, VDD = 4.75 to 5.25 V
(maximum 100 mA on even port pins
(for example, P0[2], P1[4]), maximum
100 mA on odd port pins (for
example, P0[3], P1[5])). 150 mA
maximum combined IOL budget.
mA VOH = VDD – 1.0 V, see the limitations
of the total current in the note for VOH
mA VOL = 0.75 V, see the limitations of the
total current in the note for VOL
V
VDD = 3.0 to 5.25
V
VDD = 3.0 to 5.25
mV
nA
Gross tested to 1 µA
pF
Package and pin dependent.
Temp = 25 °C
pF
Package and pin dependent.
Temp = 25 °C
Table 13. 2.7-V DC GPIO Specifications
Symbol
Description
Pull-up resistor
RPU
Pull-down resistor
RPD
High output level
VOH
VOL
Low output level
–
–
0.75
IOH
High level source current
2
–
–
VIL
VIH
VH
IOL
Input low level
Input high level
Input hysteresis
Low level sink current
–
2.0
–
11.25
–
–
90
–
0.75
–
–
–
IIL
CIN
Input leakage (absolute value)
Capacitive load on pins as input
–
–
1
3.5
–
10
COUT
Capacitive load on pins as output
–
3.5
10
Document Number: 38-12028 Rev. *R
Units
Notes
k
k
V
IOH = 2 mA (6.25 Typ), VDD = 2.4 to
3.0 V (16 mA maximum, 50 mA Typ
combined IOH budget).
V
IOL = 11.25 mA, VDD = 2.4 to 3.0 V (90
mA maximum combined IOL budget).
mA VOH = VDD – 0.4, see the limitations
of total current in note for VOH.
V
VDD = 2.4 to 3.0
V
VDD = 2.4 to 3.0
mV
mA VOL = .75, see the limitations of total
current in note for VOL.
nA
Gross tested to 1 µA
pF
Package and pin dependent.
Temp = 25 °C
pF
Package and pin dependent.
Temp = 25 °C
Page 18 of 65
CY8C24123A
CY8C24223A
CY8C24423A
DC Operational Amplifier Specifications
The following tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to
5.25 V and –40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively.
Typical parameters are measured at 5 V, 3.3 V, and 2.7 V at 25 °C and are for design guidance only.
The operational amplifier is a component of both the analog continuous time PSoC blocks and the Analog Switched Cap PSoC blocks.
The guaranteed specifications are measured in the analog continuous time PSoC block. Typical parameters are measured at 5 V at
25 °C and are for design guidance only.
Table 14. 5-V DC Operational Amplifier Specifications
Symbol
VOSOA
Description
Input offset voltage (absolute value)
Power = low, Opamp bias = high
Power = medium, Opamp bias = high
Power = high, Opamp bias = high
TCVOSOA
IEBOA
CINOA
Average input offset voltage drift
Input leakage current (port 0 analog pins)
Input capacitance (port 0 analog pins)
VCMOA
Common mode voltage range
Common mode voltage range (high power or high
Opamp bias)
GOLOA
Open loop gain
Power = low, Opamp bias = high
60
–
Power = medium, Opamp bias = high
60
–
Power = high, Opamp bias = high
80
–
High output voltage swing (internal signals)
–
Power = low, Opamp bias = high
VDD – 0.2
–
VDD – 0.2
Power = medium, Opamp bias = high
–
VDD – 0.5
Power = high, Opamp bias = high
Low output voltage swing (internal signals)
Power = low, Opamp bias = high
–
–
–
–
Power = medium, Opamp bias = high
Power = high, Opamp bias = high
–
–
Supply current (including associated AGND buffer)
Power = low, Opamp bias = low
–
150
Power = low, Opamp bias = high
–
300
Power = medium, Opamp bias = low
–
600
Power = medium, Opamp bias = high
–
1200
–
2400
Power = high, Opamp bias = low
Power = high, Opamp bias = high
–
4600
Supply voltage rejection ratio
64
80
VOHIGHOA
VOLOWOA
ISOA
PSRROA
Document Number: 38-12028 Rev. *R
Min
Typ
Max
Units
–
–
–
–
–
–
1.6
1.3
1.2
10
8
7.5
mV
mV
mV
7.0
20
4.5
35.0
–
9.5
0.0
0.5
–
–
Notes
µV/°C
pA
Gross tested to 1 µA
pF
Package and pin dependent.
Temp = 25 °C
V
The common mode input voltage
VDD
VDD – 0.5
range is measured through an
analog output buffer. The
specification includes the
limitations imposed by the
characteristics of the analog output
buffer.
Specification is applicable at high
–
dB
Opamp bias. For low Opamp bias
–
dB
mode, minimum is 60 dB.
–
dB
–
–
–
V
V
V
0.2
0.2
0.5
V
V
V
200
400
800
1600
3200
6400
–
µA
µA
µA
µA
µA
µA
dB
VSS VIN (VDD – 2.25) or
(VDD – 1.25 V) VIN  VDD
Page 19 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Table 15. 3.3-V DC Operational Amplifier Specifications
Symbol
Description
Min
Typ
Max
Units
VOSOA
Input offset voltage (absolute value)
Power = low, Opamp bias = high
Power = medium, Opamp bias = high
Power = high, Opamp bias = high
–
–
–
1.65
1.32
–
10
8
–
mV
mV
mV
Notes
Power = high, Opamp bias = high
setting is not allowed for 3.3 V VDD
operation.
TCVOSOA
Average input offset voltage drift
–
7.0
35.0
µV/°C
IEBOA
Input leakage current (port 0 analog pins)
–
20
–
pA
Gross tested to 1 A
CINOA
Input capacitance (port 0 analog pins)
–
4.5
9.5
pF
Package and pin dependent.
Temp = 25 °C
VCMOA
Common mode voltage range
0.2
–
VDD – 0.2
V
The common-mode input voltage
range is measured through an
analog output buffer. The
specification includes the limitations
imposed by the characteristics of the
analog output buffer.
GOLOA
Open loop gain
Power = low, ppamp Opamp bias = low
Power = medium, Opamp bias = low
Power = high, Opamp bias = low
60
60
80
–
–
–
–
–
–
dB
dB
dB
VOHIGHOA
High output voltage swing (internal signals)
Power = low, Opamp bias = low
Power = medium, Opamp bias = low
Power = high, Opamp bias = low
VDD – 0.2
VDD – 0.2
VDD – 0.2
–
–
–
–
–
–
V
V
V
VOLOWOA
Low output voltage swing (internal signals)
Power = low, ppamp Opamp bias = low
Power = medium, Opamp bias = low
Power = high, Opamp bias = low
–
–
–
–
–
–
0.2
0.2
0.2
V
V
V
ISOA
Supply current (including associated AGND
buffer)
Power = low, Opamp bias = low
Power = low, Opamp bias = high
Power = medium, Opamp bias = low
Power = medium, Opamp bias = high
Power = high, Opamp bias = low
Power = high, Opamp bias = high
–
–
–
–
–
–
150
300
600
1200
2400
–
200
400
800
1600
3200
–
A
A
A
A
A
A
Supply voltage rejection ratio
64
80
–
dB
PSRROA
Document Number: 38-12028 Rev. *R
Specification is applicable at low
Opamp bias. For high Opamp bias
mode (except high power, high
Opamp bias), minimum is 60 dB.
Power = high, Opamp bias = high
setting is not allowed for 3.3 V VDD
operation.
Power = high, Opamp bias = high
setting is not allowed for 3.3 V VDD
operation.
Power = high, Opamp bias = high
setting is not allowed for 3.3 V VDD
operation.
VSS VIN (VDD – 2.25) or
(VDD – 1.25 V) VIN  VDD
Page 20 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Table 16. 2.7-V DC Operational Amplifier Specifications
Symbol
Description
Min
Typ
Max
Units
VOSOA
Input offset voltage (absolute value)
Power = low, Opamp bias = high
Power = medium, Opamp bias = high
Power = high, Opamp bias = high
–
–
–
1.65
1.32
–
10
8
–
mV
mV
mV
Notes
Power = high, Opamp bias = high
setting is not allowed for 2.7 V VDD
operation.
TCVOSOA
Average input offset voltage drift
–
7.0
35.0
V/°C
IEBOA
Input leakage current (port 0 analog pins)
–
20
–
pA
Gross tested to 1 A
CINOA
Input capacitance (port 0 analog pins)
–
4.5
9.5
pF
Package and pin dependent.
Temp = 25 °C
VCMOA
Common mode voltage range
0.2
–
VDD – 0.2
V
The common-mode input voltage
range is measured through an analog
output buffer. The specification
includes the limitations imposed by
the characteristics of the analog
output buffer.
GOLOA
Open loop gain
Power = low, Opamp bias = low
Power = medium, Opamp bias = low
Power = high, Opamp bias = low
60
60
80
–
–
–
–
–
–
dB
dB
dB
VOHIGHOA
High output voltage swing (internal signals)
Power = low, Opamp bias = low
Power = medium, Opamp bias = low
Power = high, Opamp bias = low
VDD – 0.2
VDD – 0.2
VDD – 0.2
–
–
–
–
–
–
V
V
V
VOLOWOA
Low output voltage swing (internal signals)
Power = low, Opamp bias = low
Power = medium, Opamp bias = low
Power = high, Opamp bias = low
–
–
–
–
–
–
0.2
0.2
0.2
V
V
V
ISOA
Supply current (including associated AGND
buffer)
Power = low, Opamp bias = low
Power = low, Opamp bias = high
Power = medium, Opamp bias = low
Power = medium, Opamp bias = high
Power = high, Opamp bias = low
Power = high, Opamp bias = high
–
–
–
–
–
–
150
300
600
1200
2400
–
200
400
800
1600
3200
–
A
A
A
A
A
A
Supply voltage rejection ratio
64
80
–
dB
PSRROA
Specification is applicable at low
Opamp bias. For high Opamp bias
mode, (except high power, high
Opamp bias), minimum is 60 dB.
Power = high, Opamp bias = high
setting is not allowed for 2.7 V VDD
operation.
Power = high, Opamp bias = high
setting is not allowed for 2.7 V VDD
operation.
Power = high, Opamp bias = high
setting is not allowed for 2.7 V VDD
operation.
VSS VIN (VDD – 2.25) or
(VDD – 1.25 V) VIN  VDD
DC Low Power Comparator Specifications
Table 17 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively. Typical parameters
are measured at 5 V at 25 °C and are for design guidance only.
Table 17. DC Low Power Comparator Specifications
Symbol
VREFLPC
ISLPC
VOSLPC
Description
Low power comparator (LPC) reference voltage
range
LPC supply current
LPC voltage offset
Document Number: 38-12028 Rev. *R
Min
0.2
Typ
–
Max
VDD – 1
Units
V
–
–
10
2.5
40
30
µA
mV
Notes
Page 21 of 65
CY8C24123A
CY8C24223A
CY8C24423A
DC Analog Output Buffer Specifications
The following tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to
5.25 V and –40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively.
Typical parameters are measured at 5 V, 3.3 V, and 2.7 V at 25 °C and are for design guidance only.
Table 18. 5-V DC Analog Output Buffer Specifications
Symbol
CL
Description
Load Capacitance
Min
–
Typ
–
Max
200
Units
pF
VOSOB
TCVOSOB
VCMOB
ROUTOB
Input offset voltage (absolute value)
Average input offset voltage drift
Common mode input voltage range
Output resistance
Power = low
Power = high
High output voltage swing
(Load = 32 ohms to VDD/2)
Power = low
Power = high
Low output voltage swing
(Load = 32 ohms to VDD/2)
Power = low
Power = high
Supply current including Opamp bias
cell
(No Load)
Power = low
Power = high
Supply voltage rejection ratio
–
–
0.5
3
+6
–
12
–
VDD – 1.0
mV
V/°C
V
–
–
1
1
–
–
W
W
0.5 × VDD + 1.1
0.5 × VDD + 1.1
–
–
–
–
V
V
–
–
–
–
.5 × VDD – 1.3
0.5 × VDD – 1.3
V
V
–
–
1.1
2.6
5.1
8.8
mA
mA
52
64
–
dB
VOHIGHOB
VOLOWOB
ISOB
PSRROB
Notes
This specification applies to the
external circuit that is being
driven by the analog output
buffer.
VOUT > (VDD – 1.25)
Table 19. 3.3-V DC Analog Output Buffer Specifications
Symbol
CL
Description
Load Capacitance
Min
–
Typ
–
Max
200
Units
pF
VOSOB
TCVOSOB
VCMOB
ROUTOB
Input offset voltage (absolute value)
Average input offset voltage drift
Common mode input voltage range
Output resistance
Power = low
Power = high
High output voltage swing (Load = 1 K
ohms to VDD/2)
Power = low
Power = high
Low output voltage swing (Load = 1 K
ohms to VDD/2)
Power = low
Power = high
Supply current including Opamp bias
cell
(no load)
Power = low
Power = high
Supply voltage rejection ratio
–
–
0.5
3
+6
–
12
–
VDD – 1.0
mV
V/°C
V
–
–
1
1
–
–


0.5 × VDD + 1.0
0.5 × VDD + 1.0
–
–
–
–
V
V
–
–
–
–
0.5 × VDD – 1.0
0.5 × VDD – 1.0
V
V
–
–
0.8
2.0
2.0
4.3
mA
mA
52
64
–
dB
VOHIGHOB
VOLOWOB
ISOB
PSRROB
Document Number: 38-12028 Rev. *R
Notes
This specification applies to the
external circuit that is being driven
by the analog output buffer.
VOUT > (VDD – 1.25)
Page 22 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Table 20. 2.7-V DC Analog Output Buffer Specifications
Min
Typ
Max
Units
Notes
CL
Symbol
Load Capacitance
–
–
200
pF
This specification applies to the
external circuit that is being driven by
the analog output buffer.
VOSOB
Input offset voltage (absolute value)
–
3
12
mV
TCVOSOB
Average input offset voltage drift
VCMOB
Common mode input voltage range
ROUTOB
Output resistance
Power = low
Power = high
VOHIGHOB
VOLOWOB
ISOB
PSRROB
Description
–
+6
–
V/°C
0.5
–
VDD – 1.0
V
–
–
1
1
–
–


High output voltage swing (Load =
1 K ohms to VDD/2)
Power = low
Power = high
0.5 × VDD + 0.2
0.5 × VDD + 0.2
–
–
–
–
V
V
Low output voltage swing (Load = 1
K ohms to VDD/2)
Power = low
Power = high
–
–
–
–
0.5 × VDD – 0.7
0.5 × VDD – 0.7
V
V
–
0.8
2.0
2.0
4.3
mA
mA
52
64
–
dB
Supply current including Opamp
bias cell (No Load)
Power = low
Power = high
Supply voltage rejection ratio
VOUT > (VDD – 1.25).
DC Switch Mode Pump Specifications
Table 21 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively. Typical parameters
are measured at 5 V, 3.3 V, and 2.7 V at 25 °C and are for design guidance only.
Table 21. DC Switch Mode Pump (SMP) Specifications
Description
Min
Typ
Max
Units
Notes
VPUMP 5 V
Symbol
5 V output voltage from pump
4.75
5.0
5.25
V
Configuration listed in footnote.[10]
Average, neglecting ripple. SMP trip
voltage is set to 5.0 V.
VPUMP 3 V
3.3 V output voltage from pump
3.00
3.25
3.60
V
Configuration listed in footnote.[10]
Average, neglecting ripple. SMP trip
voltage is set to
3.25 V.
VPUMP 2 V
2.6 V output voltage from pump
2.45
2.55
2.80
V
Configuration listed in footnote.[10]
Average, neglecting ripple. SMP trip
voltage is set to
2.55 V.
IPUMP
Available output current
VBAT = 1.8 V, VPUMP = 5.0 V
VBAT = 1.5 V, VPUMP = 3.25 V
VBAT = 1.3 V, VPUMP = 2.55 V
5
8
8
–
–
–
–
–
–
mA
mA
mA
VBAT5 V
Input voltage range from
battery
1.8
–
5.0
V
Configuration listed in footnote.[10]
SMP trip voltage is set to 5.0 V.
VBAT3 V
Input voltage range from
battery
1.0
–
3.3
V
Configuration listed in footnote.[10]
SMP trip voltage is set to 3.25 V.
VBAT2 V
Input voltage range from
battery
1.0
–
3.0
V
Configuration listed in footnote.[10]
SMP trip voltage is set to 2.55 V.
Configuration listed in footnote.[10]
SMP trip voltage is set to 5.0 V.
SMP trip voltage is set to 3.25 V.
SMP trip voltage is set to 2.55 V.
Note
10. L1 = 2 mH inductor, C1 = 10 mF capacitor, D1 = Schottky diode. See Figure 9
Document Number: 38-12028 Rev. *R
Page 23 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Table 21. DC Switch Mode Pump (SMP) Specifications (continued)
Symbol
Description
Min
Typ
Max
Units
Notes
1.2
–
–
V
Configuration listed in footnote.[10]
0 °C  TA  100. 1.25 V at TA = –40 °C
VBATSTART
Minimum input voltage from
battery to start pump
VPUMP_Line
Line regulation (over VBAT
range)
–
5
–
%VO
Configuration listed in footnote.[10] VO
is the VDD Value for PUMP Trip”
specified by the VM[2:0] setting in the
DC POR and LVD Specification, Table
26 on page 32.
VPUMP_Load
Load regulation
–
5
–
%VO
Configuration listed in footnote.[10] VO
is the “VDD value for PUMP Trip”
specified by the VM[2:0] setting in the
DC POR and LVD Specification, Table
26 on page 32.
VPUMP_Ripple Output voltage ripple (depends
on capacitor/load)
–
100
–
mVpp Configuration listed in footnote.[10]
Load is 5 mA.
E3
Efficiency
35
50
–
E2
Efficiency
–
–
–
FPUMP
Switching frequency
–
1.3
–
MHz
DCPUMP
Switching duty cycle
–
50
–
%
%
Configuration listed in footnote.[10]
Load is 5 mA. SMP trip voltage is set
to 3.25 V.
Figure 9. Basic Switch Mode Pump Circuit
D1
Vdd
V PUMP
L1
V BAT
+
SMP
Battery
PSoC
C1
Vss
Document Number: 38-12028 Rev. *R
Page 24 of 65
CY8C24123A
CY8C24223A
CY8C24423A
DC Analog Reference Specifications
The following tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to
5.25 V and –40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively.
Typical parameters are measured at 5 V, 3.3 V, and 2.7 V at 25 °C and are for design guidance only.
The guaranteed specifications for RefHI and RefLo are measured through the Analog Continuous Time PSoC blocks. The power
levels for RefHi and RefLo refer to the Analog Reference Control register. AGND is measured at P2[4] in AGND bypass mode. Each
Analog Continuous Time PSoC block adds a maximum of 10 mV additional offset error to guaranteed AGND specifications from the
local AGND buffer. Reference control power can be set to medium or high unless otherwise noted.
Note Avoid using P2[4] for digital signaling when using an analog resource that depends on the analog reference. Some coupling of
the digital signal may appear on the AGND.
Table 22. 5-V DC Analog Reference Specifications
Reference
ARF_CR
[5:3]
0b000
Reference Power
Settings
Symbol
Reference
RefPower = high
Opamp bias = high
VREFHI
Ref High
VAGND
AGND
RefPower = high
Opamp bias = low
RefPower = medium
Opamp bias = high
RefPower = medium
Opamp bias = low
0b001
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
RefPower = medium
Opamp bias = high
RefPower = medium
Opamp bias = low
Description
Min
Typ
Max
Units
VDD/2 + Bandgap
VDD/2 + 1.136 VDD/2 + 1.288 VDD/2 + 1.409
V
VDD/2
VDD/2 – 0.138 VDD/2 + 0.003 VDD/2 + 0.132
VDD/2 – 1.417 VDD/2 – 1.289 VDD/2 – 1.154
V
VREFLO
Ref Low
VDD/2 – Bandgap
VREFHI
Ref High
VDD/2 + Bandgap
VAGND
AGND
V
V
VDD/2
VDD/2 + 1.202 VDD/2 + 1.290 VDD/2 + 1.358
VDD/2 – 0.055 VDD/2 + 0.001 VDD/2 + 0.055
V
VREFLO
Ref Low
VDD/2 – Bandgap
VDD/2 – 1.369 VDD/2 – 1.295 VDD/2 – 1.218
V
VREFHI
Ref High
VDD/2 + Bandgap
V
VAGND
AGND
VDD/2
VDD/2 + 1.211 VDD/2 + 1.292 VDD/2 + 1.357
VDD/2 – 0.055
VDD/2
VDD/2 + 0.052
VREFLO
Ref Low
VDD/2 – Bandgap
VDD/2 – 1.368 VDD/2 – 1.298 VDD/2 – 1.224
V
VREFHI
Ref High
VDD/2 + Bandgap
VDD/2 + 1.215 VDD/2 + 1.292 VDD/2 + 1.353
VDD/2 – 0.040 VDD/2 – 0.001 VDD/2 + 0.033
V
VDD/2 – 1.368 VDD/2 – 1.299 VDD/2 – 1.225
P2[4] + P2[6] P2[4] + P2[6] – P2[4] + P2[6] +
– 0.076
0.021
0.041
V
V
VAGND
AGND
VREFLO
Ref Low
VDD/2 – Bandgap
VREFHI
Ref High
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 1.3 V)
VAGND
AGND
VREFLO
Ref Low
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 1.3 V)
P2[4] – P2[6] P2[4] – P2[6] + P2[4] – P2[6] +
– 0.025
0.011
0.085
V
VREFHI
Ref High
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 1.3 V)
P2[4] + P2[6] P2[4] + P2[6] – P2[4] + P2[6] +
– 0.069
0.014
0.043
V
VAGND
AGND
VREFLO
Ref Low
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 1.3 V)
P2[4] – P2[6] P2[4] – P2[6] + P2[4] – P2[6] +
– 0.029
0.005
0.052
V
VREFHI
Ref High
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 1.3 V)
P2[4] + P2[6] P2[4] + P2[6] – P2[4] + P2[6] +
– 0.072
0.011
0.048
V
VDD/2
P2[4]
P2[4]
P2[4]
P2[4]
P2[4]
P2[4]
P2[4]
P2[4]
V
V
–
–
VAGND
AGND
VREFLO
Ref Low
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 1.3 V)
P2[4] – P2[6] P2[4] – P2[6] + P2[4] – P2[6] +
– 0.031
0.002
0.057
V
VREFHI
Ref High
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 1.3 V)
P2[4] + P2[6] P2[4] + P2[6] – P2[4] + P2[6] +
– 0.070
0.009
0.047
V
VAGND
AGND
VREFLO
Ref Low
Document Number: 38-12028 Rev. *R
P2[4]
P2[4]
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 1.3 V)
P2[4]
P2[4]
P2[4]
P2[4]
P2[4]
P2[4]
P2[4] – P2[6] P2[4] – P2[6] + P2[4] – P2[6] +
– 0.033
0.001
0.039
–
–
V
Page 25 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Table 22. 5-V DC Analog Reference Specifications (continued)
Reference
ARF_CR
[5:3]
0b010
Reference Power
Settings
Symbol
Reference
RefPower = high
Opamp bias = high
VREFHI
Ref High
RefPower = high
Opamp bias = low
RefPower = medium
Opamp bias = high
RefPower = medium
Opamp bias = low
0b011
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
RefPower = medium
Opamp bias = high
RefPower = medium
Opamp bias = low
0b100
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
RefPower = medium
Opamp bias = high
RefPower = medium
Opamp bias = low
Description
VDD
Min
Typ
Max
Units
VDD – 0.121
VDD – 0.003
VDD
V
VAGND
AGND
VDD/2 – 0.040
VDD/2
VDD/2 + 0.034
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.006
VSS + 0.019
V
VREFHI
Ref High
VDD
VDD – 0.083
VDD – 0.002
VDD
V
VDD/2
VAGND
AGND
VREFLO
Ref Low
VSS
VSS
VSS + 0.004
VSS + 0.016
V
VREFHI
Ref High
VDD
VDD – 0.075
VDD – 0.002
VDD
V
VDD/2
VAGND
AGND
VREFLO
Ref Low
VSS
VREFHI
Ref High
VDD
VAGND
AGND
VREFLO
Ref Low
VSS
VREFHI
Ref High
VAGND
AGND
VREFLO
VDD/2
VDD/2
VDD/2 – 0.040 VDD/2 – 0.001 VDD/2 + 0.033
VDD/2 – 0.040 VDD/2 – 0.001 VDD/2 + 0.032
V
V
VSS
VSS + 0.003
VSS + 0.015
V
VDD – 0.074
VDD – 0.002
VDD
V
VDD/2 – 0.040 VDD/2 – 0.001 VDD/2 + 0.032
V
VSS
VSS + 0.002
VSS + 0.014
V
3 × Bandgap
3.753
3.874
3.979
V
2 × Bandgap
2.511
2.590
2.657
V
Ref Low
Bandgap
1.243
1.297
1.333
V
VREFHI
Ref High
3 × Bandgap
3.767
3.881
3.974
V
VAGND
AGND
2 × Bandgap
2.518
2.592
2.652
V
VREFLO
Ref Low
Bandgap
1.241
1.295
1.330
V
VREFHI
Ref High
3 × Bandgap
2.771
3.885
3.979
V
VAGND
AGND
2 × Bandgap
2.521
2.593
2.649
V
VREFLO
Ref Low
Bandgap
1.240
1.295
1.331
V
VREFHI
Ref High
3 × Bandgap
3.771
3.887
3.977
V
VAGND
AGND
2 × Bandgap
2.522
2.594
2.648
V
VREFLO
Ref Low
Bandgap
VREFHI
Ref High
2 × Bandgap + P2[6]
(P2[6] = 1.3 V)
1.239
1.295
1.332
V
2.481 + P2[6]
2.569 + P2[6]
2.639 + P2[6]
V
VAGND
AGND
2.511
2.590
2.658
V
VREFLO
Ref Low
2 × Bandgap – P2[6]
(P2[6] = 1.3 V)
2.515 – P2[6]
2.602 – P2[6]
2.654 – P2[6]
V
VREFHI
Ref High
2 × Bandgap + P2[6]
(P2[6] = 1.3 V)
2.498 + P2[6]
2.579 + P2[6]
2.642 + P2[6]
V
VAGND
AGND
2.518
2.592
2.652
V
VREFLO
Ref Low
2 × Bandgap – P2[6]
(P2[6] = 1.3 V)
2.513 – P2[6]
2.598 – P2[6]
2.650 – P2[6]
V
VREFHI
Ref High
2 × Bandgap + P2[6]
(P2[6] = 1.3 V)
2.504 + P2[6]
2.583 + P2[6]
2.646 + P2[6]
V
VAGND
AGND
2.521
2.592
2.650
V
VREFLO
Ref Low
2 × Bandgap – P2[6]
(P2[6] = 1.3 V)
2.513 – P2[6]
2.596 – P2[6]
2.649 – P2[6]
V
VREFHI
Ref High
2 × Bandgap + P2[6]
(P2[6] = 1.3 V)
2.505 + P2[6]
2.586 + P2[6]
2.648 + P2[6]
V
VAGND
AGND
2.521
2.594
2.648
V
VREFLO
Ref Low
2.513 – P2[6]
2.595 – P2[6]
2.648 – P2[6]
V
Document Number: 38-12028 Rev. *R
2 × Bandgap
2 × Bandgap
2 × Bandgap
2 × Bandgap
2 × Bandgap – P2[6]
(P2[6] = 1.3 V)
Page 26 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Table 22. 5-V DC Analog Reference Specifications (continued)
Reference
ARF_CR
[5:3]
0b101
Reference Power
Settings
Symbol
Reference
RefPower = high
Opamp bias = high
VREFHI
Ref High
RefPower = high
Opamp bias = low
RefPower = medium
Opamp bias = high
RefPower = medium
Opamp bias = low
0b110
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
RefPower = medium
Opamp bias = high
RefPower = medium
Opamp bias = low
0b111
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
RefPower = medium
Opamp bias = high
RefPower = medium
Opamp bias = low
Description
P2[4] + Bandgap
(P2[4] = VDD/2)
P2[4]
Min
Typ
Max
Units
P2[4] + 1.228
P2[4] + 1.284
P2[4] + 1.332
V
VAGND
AGND
P2[4]
P2[4]
P2[4]
–
VREFLO
Ref Low
P2[4] – Bandgap
(P2[4] = VDD/2)
P2[4] – 1.358
P2[4] – 1.293
P2[4] – 1.226
V
VREFHI
Ref High
P2[4] + Bandgap
(P2[4] = VDD/2)
P2[4] + 1.236
P2[4] + 1.289
P2[4] + 1.332
V
VAGND
AGND
P2[4]
P2[4]
P2[4]
–
VREFLO
Ref Low
P2[4] – Bandgap
(P2[4] = VDD/2)
P2[4] – 1.357
P2[4] – 1.297
P2[4] – 1.229
V
VREFHI
Ref High
P2[4] + Bandgap
(P2[4] = VDD/2)
P2[4] + 1.237
P2[4] + 1.291
P2[4] + 1.337
V
VAGND
AGND
P2[4]
P2[4]
P2[4]
–
VREFLO
Ref Low
P2[4] – Bandgap
(P2[4] = VDD/2)
P2[4] – 1.356
P2[4] – 1.299
P2[4] – 1.232
V
VREFHI
Ref High
P2[4] + Bandgap
(P2[4] = VDD/2)
P2[4] + 1.237
P2[4] + 1.292
P2[4] + 1.337
V
VAGND
AGND
P2[4]
P2[4]
P2[4]
–
VREFLO
Ref Low
P2[4] – Bandgap
(P2[4] = VDD/2)
P2[4] – 1.357
P2[4] – 1.300
P2[4] – 1.233
V
VREFHI
Ref High
2 × Bandgap
2.512
2.594
2.654
V
VAGND
AGND
Bandgap
1.250
1.303
1.346
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.011
VSS + 0.027
V
VREFHI
Ref High
2 × Bandgap
2.515
2.592
2.654
V
VAGND
AGND
Bandgap
1.253
1.301
1.340
V
P2[4]
P2[4]
P2[4]
VREFLO
Ref Low
VSS
VSS
VSS + 0.006
VSS + 0.02
V
VREFHI
Ref High
2 × Bandgap
2.518
2.593
2.651
V
VAGND
AGND
Bandgap
1.254
1.301
1.338
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.004
VSS + 0.017
V
VREFHI
Ref High
2 × Bandgap
2.517
2.594
2.650
V
VAGND
AGND
Bandgap
1.255
1.300
1.337
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.003
VSS + 0.015
V
VREFHI
Ref High
3.2 × Bandgap
4.011
4.143
4.203
V
1.6 × Bandgap
2.020
2.075
2.118
V
VSS
VSS + 0.011
VSS + 0.026
V
4.138
4.203
V
V
VAGND
AGND
VREFLO
Ref Low
VSS
VREFHI
Ref High
3.2 × Bandgap
4.022
1.6 × Bandgap
2.023
2.075
2.114
VSS
VSS + 0.006
VSS + 0.017
V
4.141
4.207
V
VAGND
AGND
VREFLO
Ref Low
VSS
VREFHI
Ref High
3.2 × Bandgap
4.026
1.6 × Bandgap
2.024
2.075
2.114
V
VSS
VSS + 0.004
VSS + 0.015
V
VAGND
AGND
VREFLO
Ref Low
VSS
VREFHI
Ref High
3.2 × Bandgap
4.030
4.143
4.206
V
VAGND
AGND
1.6 × Bandgap
2.024
2.076
2.112
V
VREFLO
Ref Low
VSS
VSS + 0.003
VSS + 0.013
V
Document Number: 38-12028 Rev. *R
VSS
Page 27 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Table 23. 3.3-V DC Analog Reference Specifications
Reference
ARF_CR
[5:3]
0b000
Reference Power
Settings
Symbol
Reference
RefPower = high
Opamp bias = high
VREFHI
Ref High
VAGND
AGND
VREFLO
Ref Low
VREFHI
Ref High
VAGND
AGND
RefPower = high
Opamp bias = low
RefPower = medium
Opamp bias = high
RefPower = medium
Opamp bias = low
0b001
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
RefPower = medium
Opamp bias = high
RefPower = medium
Opamp bias = low
0b010
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
RefPower = medium
Opamp bias = high
RefPower = medium
Opamp bias = low
0b011
All power settings
Not allowed at 3.3 V
Description
Min
Typ
Max
Units
VDD/2 + Bandgap
VDD/2 + 1.170 VDD/2 + 1.288 VDD/2 + 1.376
V
VDD/2
VDD/2 – Bandgap
VDD/2 – 0.098 VDD/2 + 0.003 VDD/2 + 0.097
VDD/2 – 1.386 VDD/2 – 1.287 VDD/2 – 1.169
V
VDD/2 + Bandgap
VDD/2 + 1.210 VDD/2 + 1.290 VDD/2 + 1.355
V
VDD/2
V
V
VREFLO
Ref Low
VDD/2 – Bandgap
VDD/2 – 0.055 VDD/2 + 0.001 VDD/2 + 0.054
VDD/2 – 1.359 VDD/2 – 1.292 VDD/2 – 1.214
VREFHI
Ref High
VDD/2 + Bandgap
VDD/2 + 1.198 VDD/2 + 1.292 VDD/2 + 1.368
V
VAGND
AGND
VDD/2
VDD/2 – 0.041
VDD/2 + 0.04
V
VDD/2
V
VREFLO
Ref Low
VDD/2 – Bandgap
VDD/2 – 1.362 VDD/2 – 1.295 VDD/2 – 1.220
V
VREFHI
Ref High
VDD/2 + Bandgap
V
VAGND
AGND
VDD/2
VDD/2 + 1.202 VDD/2 + 1.292 VDD/2 + 1.364
VDD/2 – 0.033
VDD/2
VDD/2 + 0.030
V
VREFLO
Ref Low
VDD/2 – Bandgap
VDD/2 – 1.364 VDD/2 – 1.297 VDD/2 – 1.222
V
VREFHI
Ref High
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] + P2[6] P2[4] + P2[6] – P2[4] + P2[6] +
– 0.072
0.017
0.041
V
VAGND
AGND
VREFLO
Ref Low
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] – P2[6] P2[4] – P2[6] + P2[4] – P2[6] +
– 0.029
0.010
0.048
V
VREFHI
Ref High
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] + P2[6] P2[4] + P2[6] – P2[4] + P2[6] +
– 0.066
0.010
0.043
V
P2[4]
P2[4]
P2[4]
P2[4]
–
VAGND
AGND
VREFLO
Ref Low
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] – P2[6] P2[4] – P2[6] + P2[4] – P2[6] +
– 0.024
0.004
0.034
V
VREFHI
Ref High
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] + P2[6] P2[4] + P2[6] – P2[4] + P2[6] +
– 0.073
0.007
0.053
V
VAGND
AGND
VREFLO
Ref Low
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] – P2[6] P2[4] – P2[6] + P2[4] – P2[6] +
– 0.028
0.002
0.033
V
VREFHI
Ref High
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] + P2[6] P2[4] + P2[6] – P2[4] + P2[6] +
– 0.073
0.006
0.056
V
P2[4]
P2[4]
VAGND
AGND
VREFLO
Ref Low
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
VREFHI
Ref High
VDD
VAGND
AGND
VREFLO
Ref Low
VSS
VREFHI
Ref High
VDD
VAGND
AGND
P2[4]
VDD/2
VDD/2
P2[4]
P2[4]
P2[4]
P2[4]
P2[4]
P2[4]
–
–
P2[4]
P2[4]
P2[4]
–
P2[4] – P2[6]
– 0.030
P2[4] – P2[6]
P2[4] – P2[6] +
0.032
V
VDD – 0.102
VDD – 0.003
VDD
V
VDD/2 – 0.040 VDD/2 + 0.001 VDD/2 + 0.039
VSS
VSS + 0.005
VSS + 0.020
V
V
VDD – 0.082
VDD – 0.002
VDD
V
VDD/2 – 0.031
VDD/2
VDD/2 + 0.028
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.003
VSS + 0.015
V
VREFHI
Ref High
VDD
VDD – 0.083
VDD – 0.002
VDD
V
VAGND
AGND
VDD/2
VREFLO
Ref Low
VSS
VREFHI
Ref High
VDD
VAGND
AGND
VREFLO
Ref Low
–
–
Document Number: 38-12028 Rev. *R
VDD/2
VSS
–
VDD/2 – 0.032 VDD/2 – 0.001 VDD/2 + 0.029
VSS
VSS + 0.002
VSS + 0.014
VDD – 0.081
VDD – 0.002
VDD
VDD/2 – 0.033 VDD/2 – 0.001 VDD/2 + 0.029
VSS
VSS + 0.002
VSS + 0.013
–
–
–
V
V
V
V
V
–
Page 28 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Table 23. 3.3-V DC Analog Reference Specifications (continued)
Reference
ARF_CR
[5:3]
Reference Power
Settings
Symbol
Reference
Description
Typ
Max
Units
–
–
–
–
P2[4] + 1.211
P2[4] + 1.285
P2[4] + 1.348
V
P2[4]
P2[4]
P2[4]
–
0b100
All power settings
Not allowed at 3.3 V
–
–
0b101
RefPower = high
Opamp bias = high
VREFHI
Ref High
VAGND
AGND
VREFLO
Ref Low
P2[4] – Bandgap
(P2[4] = VDD/2)
P2[4] – 1.354
P2[4] – 1.290
P2[4] – 1.197
V
VREFHI
Ref High
P2[4] + Bandgap
(P2[4] = VDD/2)
P2[4] + 1.209
P2[4] + 1.289
P2[4] + 1.353
V
RefPower = high
Opamp bias = low
RefPower = medium
Opamp bias = high
RefPower = medium
Opamp bias = low
0b110
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
RefPower = medium
Opamp bias = high
RefPower = medium
Opamp bias = low
0b111
All power settings
Not allowed at 3.3 V
–
Min
P2[4] + Bandgap
(P2[4] = VDD/2)
P2[4]
VAGND
AGND
P2[4]
P2[4]
P2[4]
–
VREFLO
Ref Low
P2[4] – Bandgap
(P2[4] = VDD/2)
P2[4] – 1.352
P2[4] – 1.294
P2[4] – 1.222
V
VREFHI
Ref High
P2[4] + Bandgap
(P2[4] = VDD/2)
P2[4] + 1.218
P2[4] + 1.291
P2[4] + 1.351
V
P2[4]
VAGND
AGND
P2[4]
P2[4]
P2[4]
–
VREFLO
Ref Low
P2[4] – Bandgap
(P2[4] = VDD/2)
P2[4] – 1.351
P2[4] – 1.296
P2[4] – 1.224
V
VREFHI
Ref High
P2[4] + Bandgap
(P2[4] = VDD/2)
P2[4] + 1.215
P2[4] + 1.292
P2[4] + 1.354
V
VAGND
AGND
P2[4]
P2[4]
P2[4]
–
VREFLO
Ref Low
P2[4] – Bandgap
(P2[4] = VDD/2)
P2[4] – 1.352
P2[4] – 1.297
P2[4] – 1.227
V
VREFHI
Ref High
2 × Bandgap
2.460
2.594
2.695
V
Bandgap
1.257
1.302
1.335
V
VSS
VSS + 0.01
VSS + 0.029
V
2.592
2.692
V
V
P2[4]
P2[4]
VAGND
AGND
VREFLO
Ref Low
VSS
VREFHI
Ref High
2 × Bandgap
2.462
Bandgap
1.256
1.301
1.332
VSS
VSS + 0.005
VSS + 0.017
V
2.593
2.682
V
VAGND
AGND
VREFLO
Ref Low
VSS
VREFHI
Ref High
2 × Bandgap
2.473
Bandgap
1.257
1.301
1.330
V
VSS
VSS + 0.003
VSS + 0.014
V
VAGND
AGND
VREFLO
Ref Low
VSS
VREFHI
Ref High
2 × Bandgap
2.470
2.594
2.685
V
VAGND
AGND
Bandgap
1.256
1.300
1.332
V
VREFLO
Ref Low
VSS
VSS + 0.002
VSS + 0.012
V
–
–
–
–
–
–
Document Number: 38-12028 Rev. *R
VSS
–
Page 29 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Table 24. 2.7-V DC Analog Reference Specifications
Reference
ARF_CR
[5:3]
Reference Power
Settings
Symbol
Reference
0b000
All power settings
Not allowed at 2.7 V
–
–
0b001
RefPower = medium
Opamp bias = high
VREFHI
Ref High
RefPower = medium
Opamp bias = low
RefPower = low
Opamp bias = high
RefPower = low
Opamp bias = low
0b010
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
RefPower = medium
Opamp bias = high
RefPower = medium
Opamp bias = low
RefPower = low
Opamp bias = high
RefPower = low
Opamp bias = low
Description
–
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
Min
Typ
Max
Units
–
–
–
–
P2[4] + P2[6] P2[4] + P2[6] – P2[4] + P2[6] +
– 0.739
0.016
0.759
V
VAGND
AGND
VREFLO
Ref Low
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] – P2[6] P2[4] – P2[6] + P2[4] – P2[6] +
– 1.675
0.013
1.825
V
VREFHI
Ref High
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] + P2[6] P2[4] + P2[6] – P2[4] + P2[6] +
– 0.098
0.011
0.067
V
VAGND
AGND
VREFLO
Ref Low
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] – P2[6] P2[4] – P2[6] + P2[4] – P2[6] +
– 0.308
0.004
0.362
V
VREFHI
Ref High
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] + P2[6] P2[4] + P2[6] – P2[4] + P2[6] +
– 0.042
0.005
0.035
V
VAGND
AGND
VREFLO
Ref Low
VREFHI
Ref High
VAGND
AGND
VREFLO
Ref Low
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
VREFHI
Ref High
VDD
VAGND
AGND
P2[4]
P2[4]
P2[4]
P2[4]
P2[4]
P2[4]
P2[4]
P2[4]
P2[4]
–
–
P2[4]
P2[4]
P2[4]
–
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] – P2[6]
– 0.030
P2[4] – P2[6]
P2[4] – P2[6] +
0.030
V
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] + P2[6] P2[4] + P2[6] – P2[4] + P2[6] +
– 0.367
0.005
0.308
V
P2[4]
VDD/2
P2[4]
P2[4]
P2[4]
–
P2[4] – P2[6]
– 0.345
P2[4] – P2[6]
P2[4] – P2[6] +
0.301
V
VDD – 0.100
VDD – 0.003
VDD
V
VDD/2 – 0.038
VDD/2
VDD/2 + 0.036
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.005
VSS + 0.016
V
VREFHI
Ref High
VDD
VDD – 0.065
VDD – 0.002
VDD
V
VAGND
AGND
VDD/2 – 0.025
VDD/2
VDD/2 + 0.023
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.003
VSS + 0.012
V
VREFHI
Ref High
VDD
VDD – 0.054
VDD – 0.002
VDD
V
VAGND
AGND
VREFLO
Ref Low
VSS
VREFHI
Ref High
VDD
VAGND
AGND
VDD/2
VDD/2
VDD/2
VDD/2 – 0.024 VDD/2 – 0.001 VDD/2 + 0.020
V
VSS
VSS + 0.002
VSS + 0.012
V
VDD – 0.042
VDD – 0.002
VDD
V
VDD/2 – 0.027 VDD/2 – 0.001 VDD/2 + 0.022
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.001
VSS + 0.010
V
VREFHI
Ref High
VDD
VDD – 0.042
VDD – 0.002
VDD
V
VAGND
AGND
VDD/2
VDD/2 – 0.028 VDD/2 – 0.001 VDD/2 + 0.023
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.001
VSS + 0.010
V
VREFHI
Ref High
VDD
VDD – 0.036
VDD – 0.002
VDD
V
VAGND
AGND
VREFLO
Ref Low
Document Number: 38-12028 Rev. *R
VDD/2
VSS
VDD/2 – 0.184 VDD/2 – 0.001 VDD/2 + 0.159
VSS
VSS + 0.001
VSS + 0.009
V
V
Page 30 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Table 24. 2.7-V DC Analog Reference Specifications (continued) (continued)
Reference
ARF_CR
[5:3]
Reference Power
Settings
Symbol
Reference
Description
Min
Typ
Max
Units
0b011
All power settings
Not allowed at 2.7 V
–
–
–
–
–
–
–
0b100
All power settings
Not allowed at 2.7 V
–
–
–
–
–
–
–
0b101
All power settings
Not allowed at 2.7 V
–
–
–
–
–
–
–
0b110
RefPower = high
Opamp bias = high
VREFHI
Ref High
Not allowed
Not allowed
Not allowed
V
VAGND
AGND
1.160
1.302
1.340
V
V
RefPower = high
Opamp bias = low
RefPower = medium
Opamp bias = high
RefPower = medium
Opamp bias = low
RefPower = low
Opamp bias = high
RefPower = low
Opamp bias = low
0b111
All power settings
Not allowed at 2.7 V
2 × Bandgap
Bandgap
VREFLO
Ref Low
VSS
VREFHI
Ref High
2 × Bandgap
VAGND
AGND
Bandgap
VREFLO
Ref Low
VSS
VREFHI
Ref High
2 × Bandgap
VAGND
AGND
Bandgap
VREFLO
Ref Low
VSS
VREFHI
Ref High
2 × Bandgap
VAGND
AGND
VREFLO
Ref Low
VSS
VREFHI
Ref High
2 × Bandgap
VAGND
AGND
Bandgap
Bandgap
VREFLO
Ref Low
VSS
VREFHI
Ref High
2 × Bandgap
VAGND
AGND
VREFLO
Ref Low
–
–
Bandgap
VSS
–
VSS
VSS + 0.007
VSS + 0.025
Not allowed
Not allowed
Not allowed
V
1.160
1.301
1.338
V
VSS
VSS + 0.004
VSS + 0.017
V
Not allowed
Not allowed
Not allowed
V
1.160
1.301
1.338
V
VSS
VSS + 0.003
VSS + 0.013
V
Not allowed
Not allowed
Not allowed
V
1.160
1.300
1.337
V
VSS
VSS + 0.002
VSS + 0.011
V
Not allowed
Not allowed
Not allowed
V
1.252
1.300
1.339
V
V
VSS
VSS + 0.002
VSS + 0.011
Not allowed
Not allowed
Not allowed
V
1.252
1.300
1.339
V
VSS
VSS + 0.001
VSS + 0.01
V
–
–
–
–
DC Analog PSoC Block Specifications
Table 22 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively. Typical parameters
are measured at 5 V, 3.3 V, and 2.7 V at 25 °C and are for design guidance only.
Table 25. DC Analog PSoC Block Specifications
Symbol
RCT
CSC
Description
Resistor unit value (continuous time)
Capacitor unit value (switched capacitor)
Document Number: 38-12028 Rev. *R
Min
–
–
Typ
12.2
80
Max
–
–
Units
k
fF
Notes
Page 31 of 65
CY8C24123A
CY8C24223A
CY8C24423A
DC POR, SMP, and LVD Specifications
Table 23 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively. Typical parameters
are measured at 5 V, 3.3 V, and 2.7 V at 25 °C and are for design guidance only.
Note The bits PORLEV and VM in the following table refer to bits in the VLT_CR register. See the PSoC Programmable Sytem-on-Chip
Technical Reference Manual for more information on the VLT_CR register.
Table 26. DC POR and LVD Specifications
Symbol
Description
Min
Typ
Max
Units
Notes
–
2.36
2.82
4.55
2.40
2.95
4.70
V
V
V
VDD must be greater than or
equal to 2.5 V during startup,
reset from the XRES pin, or
reset from watchdog.
VPPOR0
VPPOR1
VPPOR2
VDD value for PPOR trip
PORLEV[1:0] = 00b
PORLEV[1:0] = 01b
PORLEV[1:0] = 10b
VLVD0
VLVD1
VLVD2
VLVD3
VLVD4
VLVD5
VLVD6
VLVD7
VDD value for LVD trip
VM[2:0] = 000b
VM[2:0] = 001b
VM[2:0] = 010b
VM[2:0] = 011b
VM[2:0] = 100b
VM[2:0] = 101b
VM[2:0] = 110b
VM[2:0] = 111b
2.40
2.85
2.95
3.06
4.37
4.50
4.62
4.71
2.450
2.920
3.02
3.13
4.48
4.64
4.73
4.81
2.51[11]
2.99[12]
3.09
3.20
4.55
4.75
4.83
4.95
V0
V0
V0
V0
V0
V
V
V
VPUMP0
VPUMP1
VPUMP2
VPUMP3
VPUMP4
VPUMP5
VPUMP6
VPUMP7
VDD value for SMP trip
VM[2:0] = 000b
VM[2:0] = 001b
VM[2:0] = 010b
VM[2:0] = 011b
VM[2:0] = 100b
VM[2:0] = 101b
VM[2:0] = 110b
VM[2:0] = 111b
2.500
2.96
3.03
3.18
4.54
4.62
4.71
4.89
2.550
3.02
3.10
3.250
4.64
4.73
4.82
5.00
2.62[13]
3.09
3.16
3.32[14]
4.74
4.83
4.92
5.12
V
V0
V0
V0
V0
V
V
V
Notes
11. Always greater than 50 mV above VPPOR (PORLEV=00) for falling supply.
12. Always greater than 50 mV above VPPOR (PORLEV=01) for falling supply.
13. Always greater than 50 mV above VLVD0.
14. Always greater than 50 mV above VLVD3.
Document Number: 38-12028 Rev. *R
Page 32 of 65
CY8C24123A
CY8C24223A
CY8C24423A
DC Programming Specifications
Table 27 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively. Typical parameters
are measured at 5 V, 3.3 V, and 2.7 V at 25 °C and are for design guidance only.
Table 27. DC Programming Specifications
Symbol
VDDP
Description
VDD for programming and erase
Min
4.5
Typ
5
Max
5.5
Units
V
VDDLV
Low VDD for verify
2.4
2.5
2.6
V
VDDHV
High VDD for verify
5.1
5.2
5.3
V
VDDIWRITE
Supply voltage for flash write operation
2.7
5.25
V
IDDP
VILP
VIHP
IILP
–
–
2.1
–
5
–
–
–
25
0.8
–
0.2
mA
V
V
mA
–
–
1.5
mA
VOLV
VOHV
FlashENPB
Supply current during programming or verify
Input low voltage during programming or verify
Input high voltage during programming or verify
Input current when applying VILP to P1[0] or P1[1]
during programming or verify
Input current when applying VIHP to P1[0] or P1[1]
during programming or verify
Output low voltage during programming or verify
Output high voltage during programming or verify
Flash endurance (per block)
–
VDD – 1.0
50,000[15]
–
–
–
VSS + 0.75
VDD
–
V
V
–
FlashENT
FlashDR
Flash endurance (total)[16]
Flash data retention
1,800,000
10
–
–
–
–
–
Years
IIHP
Notes
This specification applies
to the functional requirements of external
programmer tools
This specification applies
to the functional requirements of external
programmer tools
This specification applies
to the functional requirements of external
programmer tools
This specification applies
to this device when it is
executing internal flash
writes
Driving internal pull-down
resistor
Driving internal pull-down
resistor
Erase/write cycles per
block
Erase/write cycles
DC I2C Specifications
Table 28 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively. Typical parameters
are measured at 5 V, 3.3 V, and 2.7 V at 25 °C and are for design guidance only.
Table 28. DC I2C Specifications[17]
Symbol
VILI2C
Input low level
Description
VIHI2C
Input high level
Min
–
–
0.7 × VDD
Typ
–
–
–
Max
0.3 × VDD
0.25 × VDD
–
Units
V
V
V
Notes
2.4 V VDD 3.6 V
4.75 V VDD 5.25 V
2.4 V VDD 5.25 V
Notes
15. The 50,000 cycle flash endurance per block is only guaranteed if the flash is operating within one voltage range. Voltage ranges are 2.4 V to 3.0 V, 3.0 V to
3.6 V, and 4.75 V to 5.25 V.
16. A maximum of 36 × 50,000 block endurance cycles is allowed. This may be balanced between operations on 36 × 1 blocks of 50,000 maximum cycles each, 36 × 2
blocks of 25,000 maximum cycles each, or 36 × 4 blocks of 12,500 maximum cycles each (to limit the total number of cycles to 36 × 50,000 and that no single block
ever sees more than 50,000 cycles).
For the full industrial range, the user must employ a temperature sensor user module (FlashTemp) and feed the result to the temperature argument before writing.
Refer to the Flash APIs application note Design Aids – Reading and Writing PSoC® Flash – AN2015 for more information.
17. All GPIOs meet the DC GPIO VIL and VIH specifications found in the DC GPIO Specifications sections. The I2C GPIO pins also meet the above specs.
Document Number: 38-12028 Rev. *R
Page 33 of 65
CY8C24123A
CY8C24223A
CY8C24423A
AC Electrical Characteristics
AC Chip-Level Specifications
These tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively. Typical parameters
are measured at 5 V, 3.3 V, and 2.7 V at 25 °C and are for design guidance only.
Table 29. 5-V and 3.3-V AC Chip-Level Specifications
Symbol
FIMO24
Description
Internal main oscillator (IMO) frequency for
24 MHz
Min
23.4
Typ
24
Max
24.6[18,19]
FIMO6
IMO frequency for 6 MHz
5.5
6
6.5[18,19]
FCPU1
FCPU2
F48M
CPU frequency (5 V nominal)
CPU frequency (3.3 V nominal)
Digital PSoC block frequency
0.937
0.937
0
24
12
48
24.6[18]
12.3[19]
49.2[18,20]
F24M
F32K1
F32K2
Digital PSoC block frequency
ILO frequency
External crystal oscillator
0
15
–
24
32
32.768
24.6[20]
64
–
F32K_U
ILO untrimmed frequency
5
–
100
FPLL
PLL frequency
–
23.986
–
TPLLSLEW
TPLLSLEWSLOW
TOS
TOSACC
PLL lock time
PLL lock time for low gain setting
External crystal oscillator startup to 1%
External crystal oscillator startup to
100 ppm
0.5
0.5
–
–
–
–
1700
2800
10
50
2620
3800
tXRST
DC24M
DCILO
Step24M
Fout48M
FMAX
External reset pulse width
24 MHz duty cycle
ILO duty cycle
24 MHz trim step size
48 MHz output frequency
Maximum frequency of signal on row input
or row output.
Power supply slew rate
Time from end of POR to CPU executing
code
10
40
20
–
46.8
–
–
50
50
50
48.0
–
–
60
80
–
49.2[18,19]
12.3
–
–
–
16
250
100
SRPOWER_UP
tPOWERUP
Units
Notes
MHz Trimmed for 5 V or 3.3 V operation
using factory trim values.
See Figure 8 on page 16.
SLIMO mode = 0.
MHz Trimmed for 5 V or 3.3 V operation
using factory trim values.
See Figure 8 on page 16.
SLIMO mode = 1.
MHz SLIMO mode = 0.
MHz SLIMO mode = 0.
MHz Refer to the AC Digital Block
Specifications.
MHz
kHz
kHz Accuracy is capacitor and crystal
dependent. 50% duty cycle.
kHz After a reset and before the M8C
starts to run, the ILO is not trimmed.
See the System Resets section of
the PSoC Technical Reference
Manual for details on timing this
MHz Is a multiple (x732) of crystal
frequency.
ms
ms
ms
ms The crystal oscillator frequency is
within 100 ppm of its final value by
the end of the Tosacc period. Correct
operation assumes a properly
loaded 1 µW maximum drive level
32.768 kHz crystal.
3.0 V  VDD  5.5 V,
–40 °C  TA  85 °C.
s
%
%
kHz
MHz Trimmed. Using factory trim values.
MHz
V/ms VDD slew rate during power-up.
ms Power-up from 0 V. See the System
Resets section of the PSoC
Technical Reference Manual.
Notes
18. 4.75 V < VDD < 5.25 V.
19. 3.0 V < VDD < 3.6 V. See application note Adjusting PSoC® Trims for 3.3 V and 2.7 V Operation – AN2012 for information on trimming for operation at 3.3 V.
20. See the individual user module datasheets for information on maximum frequencies for user modules.
21. Refer to Cypress Jitter Specifications application note, Understanding Datasheet Jitter Specifications for Cypress Timing Products – AN5054 for more information.
Document Number: 38-12028 Rev. *R
Page 34 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Table 29. 5-V and 3.3-V AC Chip-Level Specifications (continued)
Symbol
tjit_IMO [24]
tjit_PLL [24]
Description
24 MHz IMO cycle-to-cycle jitter (RMS)
24 MHz IMO long term N cycle-to-cycle
jitter (RMS)
24 MHz IMO period jitter (RMS)
24 MHz IMO cycle-to-cycle jitter (RMS)
24 MHz IMO long term N cycle-to-cycle
jitter (RMS)
24 MHz IMO period jitter (RMS)
Min
–
–
Typ
200
300
Max
700
900
–
–
–
100
200
300
400
800
1200
–
100
700
Units
ps N = 32
ps
ps
ps
Notes
N = 32
Table 30. 2.7-V AC Chip-Level Specifications
Symbol
FIMO12
Description
IMO frequency for 12 MHz
Min
11.5
Typ
12
Max
12.7[22,23]
FIMO6
IMO frequency for 6 MHz
5.5
6
6.5[22,23]
FCPU1
FBLK27
CPU frequency (2.7 V nominal)0
Digital PSoC block frequency
(2.7 V nominal)
ILO frequency
ILO untrimmed frequency
0.9370
0
30
12
3.15[22]
12.7[22,23]
8
5
32
–
96
100
External reset pulse width
12 MHz duty cycle
ILO duty cycle
Maximum frequency of signal on row input
or row output.
Power supply slew rate
Time from end of POR to CPU executing
code
10
40
20
–
–
50
50
–
–
60
80
12.7
–
–
–
16
250
100
12 MHz IMO cycle-to-cycle jitter (RMS)
12 MHz IMO long term N cycle-to-cycle
jitter (RMS)
12 MHz IMO period jitter (RMS)
12 MHz IMO cycle-to-cycle jitter (RMS)
12 MHz IMO long term N cycle-to-cycle
jitter (RMS)
12 MHz IMO period jitter (RMS)
–
–
400
600
1000
1300
–
–
–
100
400
700
500
1000
1300
–
300
500
F32K1
F32K_U
tXRST
DC12M
DCILO
FMAX
SRPOWER_UP
tPOWERUP
tjit_IMO[24]
tjit_PLL
[24]
Units
Notes
MHz Trimmed for 2.7 V operation using
factory trim values.
See Figure 8 on page 16.
SLIMO mode = 1.
MHz Trimmed for 2.7 V operation using
factory trim values.
See Figure 8 on page 16.
SLIMO mode = 1.
MHz0 SLIMO mode = 0.
MHz0 Refer to the AC Digital Block
Specifications.
kHz
kHz After a reset and before the M8C
starts to run, the ILO is not trimmed.
See the System Resets section of
the PSoC Technical Reference
Manual for details on timing this
µs
%
%
MHz
V/ms VDD slew rate during power-up.
ms Power-up from 0 V. See the System
Resets section of the PSoC
Technical Reference Manual.
ps N = 32
ps
ps
ps
N = 32
Notes
22. 2.4 V < VDD < 3.0 V.
23. Refer to application note Adjusting PSoC® Trims for 3.3 V and 2.7 V Operation – AN2012 for information on trimming for operation at 3.3 V.
24. Refer to Cypress Jitter Specifications application note, Understanding Datasheet Jitter Specifications for Cypress Timing Products – AN5054 for more information.
Document Number: 38-12028 Rev. *R
Page 35 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Figure 10. PLL Lock Timing Diagram
PLL
Enable
TPLLSLEW
24 MHz
FPLL
PLL
Gain
0
Figure 11. PLL Lock for Low Gain Setting Timing Diagram
PLL
Enable
TPLLSLEWLOW
24 MHz
FPLL
PLL
Gain
1
Figure 12. External Crystal Oscillator Startup Timing Diagram
32K
Select
32 kHz
TOS
F32K2
Document Number: 38-12028 Rev. *R
Page 36 of 65
CY8C24123A
CY8C24223A
CY8C24423A
AC GPIO Specifications
These tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively. Typical parameters
are measured at 5 V, 3.3 V, and 2.7 V at 25 °C and are for design guidance only.
Table 31. 5-V and 3.3-V AC GPIO Specifications
Symbol
FGPIO
tRiseF
tFallF
tRiseS
tFallS
Description
GPIO operating frequency
Rise time, normal strong mode, Cload = 50 pF
Fall time, normal strong mode, Cload = 50 pF
Rise time, slow strong mode, Cload = 50 pF
Fall time, slow strong mode, Cload = 50 pF
Min
0
3
2
10
10
Typ
–
–
–
27
22
Max
12
18
18
–
–
Units
MHz
ns
ns
ns
ns
Notes
Normal Strong Mode
VDD = 4.5 to 5.25 V, 10% to 90%
VDD = 4.5 to 5.25 V, 10% to 90%
VDD = 3 to 5.25 V, 10% to 90%
VDD = 3 to 5.25 V, 10% to 90%
Min
0
6
6
18
18
Typ
–
–
–
40
40
Max
3
50
50
120
120
Units
MHz
ns
ns
ns
ns
Notes
Normal strong mode
VDD = 2.4 to 3.0 V, 10% to 90%
VDD = 2.4 to 3.0 V, 10% to 90%
VDD = 2.4 to 3.0 V, 10% to 90%
VDD = 2.4 to 3.0 V, 10% to 90%
Table 32. 2.7-V AC GPIO Specifications
Symbol
FGPIO
tRiseF
tFallF
tRiseS
tFallS
Description
GPIO operating frequency
Rise time, normal strong mode, Cload = 50 pF
Fall time, normal strong mode, Cload = 50 pF
Rise time, slow strong mode, Cload = 50 pF
Fall time, slow strong mode, Cload = 50 pF
Figure 0-1. GPIO Timing Diagram
90%
GPIO
Pin
Output
Voltage
10%
TRiseF
TRiseS
Document Number: 38-12028 Rev. *R
TFallF
TFallS
Page 37 of 65
CY8C24123A
CY8C24223A
CY8C24423A
AC Operational Amplifier Specifications
The following tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to
5.25 V and –40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively.
Typical parameters are measured at 5 V, 3.3 V, and 2.7 V at 25 °C and are for design guidance only.
Settling times, slew rates, and gain bandwidth are based on the analog continuous time PSoC block.
Power = high and Opamp bias = high is not supported at 3.3 V and 2.7 V.
Table 33. 5-V AC Operational Amplifier Specifications
Symbol
tROA
tSOA
SRROA
SRFOA
BWOA
ENOA
Description
Rising settling time from 80% of V to 0.1% of V
(10 pF load, unity gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Power = high, Opamp bias = high
Falling settling time from 20% of V to 0.1% of V
(10 pF load, unity gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Power = high, Opamp bias = high
Rising slew rate (20% to 80%) (10 pF load, unity gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Power = high, Opamp bias = high
Falling slew rate (20% to 80%) (10 pF load, unity gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Power = high, Opamp bias = high
Gain bandwidth product
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Power = high, Opamp bias = high
Noise at 1 kHz (Power = medium, Opamp bias = high)
Min
Typ
Max
Units
–
–
–
–
–
–
3.9
0.72
0.62
µs
µs
µs
–
–
–
–
–
–
5.9
0.92
0.72
µs
µs
µs
0.15
1.7
6.5
–
–
–
–
–
–
V/µs
V/µs
V/µs
0.01
0.5
4.0
–
–
–
–
–
–
V/µs
V/µs
V/µs
0.75
3.1
5.4
–
–
–
–
100
–
–
–
–
MHz
MHz
MHz
nV/rt-Hz
Min
Typ
Max
Units
–
–
–
–
3.92
0.72
µs
µs
–
–
–
–
5.41
0.72
µs
µs
0.31
2.7
–
–
–
–
V/µs
V/µs
0.24
1.8
–
–
–
–
V/µs
V/µs
0.67
2.8
–
–
–
100
–
–
–
MHz
MHz
nV/rt-Hz
Table 34. 3.3-V AC Operational Amplifier Specifications
Symbol
tROA
tSOA
SRROA
SRFOA
BWOA
ENOA
Description
Rising settling time from 80% of V to 0.1% of V
(10 pF load, unity gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Falling settling time from 20% of V to 0.1% of V
(10 pF load, unity gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Rising slew rate (20% to 80%) (10 pF load, unity gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Falling slew rate (20% to 80%) (10 pF load, unity gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Gain bandwidth product
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Noise at 1 kHz (Power = medium, Opamp bias = high)
Document Number: 38-12028 Rev. *R
Page 38 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Table 35. 2.7-V AC Operational Amplifier Specifications
Symbol
tROA
tSOA
Min
Typ
Max
Units
Rising settling time from 80% of V to 0.1% of V
(10 pF load, unity gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Description
–
–
–
–
3.92
0.72
µs
µs
Falling settling time from 20% of V to 0.1% of V
(10 pF load, unity gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
–
–
–
–
5.41
0.72
µs
µs
SRROA
Rising slew rate (20% to 80%) (10 pF load, unity gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
0.31
2.7
–
–
–
–
V/µs
V/µs
SRFOA
Falling slew rate (20% to 80%) (10 pF load, unity gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
0.24
1.8
–
–
–
–
V/µs
V/µs
BWOA
Gain bandwidth product
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
0.67
2.8
–
–
–
–
MHz
MHz
ENOA
Noise at 1 kHz (Power = medium, Opamp bias = high)
–
100
–
nV/rt-Hz
When bypassed by a capacitor on P2[4], the noise of the analog ground signal distributed to each block is reduced by a factor of up
to 5 (14 dB). This is at frequencies above the corner frequency defined by the on-chip 8.1 K resistance and the external capacitor.
Figure 13. Typical AGND Noise with P2[4] Bypass
nV/rtHz
10000
0
0.01
0.1
1.0
10
1000
100
0.001
0.01
0.1 Freq (kHz)
1
10
100
At low frequencies, the opamp noise is proportional to 1/f, power independent, and determined by device geometry.
At high frequencies, increased power level reduces the noise spectrum level.
Document Number: 38-12028 Rev. *R
Page 39 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Figure 14. Typical Opamp Noise
nV/rtHz
10000
PH_BH
PH_BL
PM_BL
PL_BL
1000
100
10
0.001
0.01
0.1
Freq (kHz)
1
10
100
AC Low Power Comparator Specifications
Table 36 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively. Typical parameters
are measured at 5 V at 25 °C and are for design guidance only.
Table 36. AC Low Power Comparator Specifications
Symbol
tRLPC
Description
LPC response time
Document Number: 38-12028 Rev. *R
Min
–
Typ
–
Max
50
Units
µs
Notes
 50 mV overdrive comparator
reference set within VREFLPC
Page 40 of 65
CY8C24123A
CY8C24223A
CY8C24423A
AC Digital Block Specifications
The following tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to
5.25 V and –40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively.
Typical parameters are measured at 5 V, 3.3 V, and 2.7 V at 25 °C and are for design guidance only.
Table 37. 5-V and 3.3-V AC Digital Block Specifications
Function
All functions
Timer
Counter
Dead Band
CRCPRS
(PRS
Mode)
CRCPRS
(CRC
Mode)
SPIM
SPIS
Transmitter
Receiver
Description
Block input clock frequency
VDD  4.75 V
VDD < 4.75 V
Input clock frequency
No capture, VDD 4.75 V
No capture, VDD < 4.75 V
With capture
Capture pulse width
Input clock frequency
No enable input, VDD  4.75 V
No enable input, VDD < 4.75 V
With enable input
Enable input pulse width
Kill pulse width
Asynchronous restart mode
Synchronous restart mode
Disable mode
Input clock frequency
VDD  4.75 V
VDD < 4.75 V
Input clock frequency
VDD  4.75 V
VDD < 4.75 V
Input clock frequency
Min
Typ
Max
Unit
–
–
–
–
49.2
24.6
MHz
MHz
–
–
–
50[25]
–
–
–
–
49.2
24.6
24.6
–
MHz
MHz
MHz
ns
–
–
–
50[25]
–
–
–
–
49.2
24.6
24.6
–
MHz
MHz
MHz
ns
20
50[25]
50[25]
–
–
–
–
–
–
ns
ns
ns
–
–
–
–
49.2
24.6
MHz
MHz
–
–
–
–
–
–
49.2
24.6
24.6
MHz
MHz
MHz
–
–
8.2
MHz
Input clock (SCLK) frequency
Width of SS_negated between
transmissions
Input clock frequency
VDD  4.75 V, 2 stop bits
VDD  4.75 V, 1 stop bit
VDD < 4.75 V
Input clock frequency
–
50[25]
–
–
4.1
–
MHz
ns
–
–
–
–
–
–
49.2
24.6
24.6
MHz
MHz
MHz
VDD  4.75 V, 2 stop bits
VDD  4.75 V, 1 stop bit
VDD < 4.75 V
–
–
–
Input clock frequency
Notes
The SPI serial clock (SCLK) frequency is equal to
the input clock frequency divided by 2.
The input clock is the SPI SCLK in SPIS mode.
The baud rate is equal to the input clock frequency
divided by 8.
The baud rate is equal to the input clock frequency
divided by 8.
–
–
–
49.2
24.6
24.6
MHz
MHz
MHz
Note
25. 50 ns minimum input pulse width is based on the input synchronizers running at 24 MHz (42 ns nominal period).
Document Number: 38-12028 Rev. *R
Page 41 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Table 38. 2.7-V AC Digital Block Specifications
Function
Description
All
Functions
Block input clock frequency
Timer
Capture pulse width
Input clock frequency, with or without capture
Counter
Dead Band
Min
Typ
Max
Units
Notes
–
–
12.7
MHz
2.4 V < VDD < 3.0 V
100[26]
–
–
ns
–
–
12.7
MHz
100[26]
–
–
ns
Input clock frequency, no enable input
–
–
12.7
MHz
Input clock frequency, enable input
–
–
12.7
MHz
Asynchronous restart mode
20
–
–
ns
Synchronous restart mode
100[26]
–
–
ns
Disable mode0
100[26]
–
–
ns
Enable Input Pulse Width
Kill pulse width:
Input clock frequency
–
–
12.7
MHz
CRCPRS
Input clock frequency
(PRS Mode)
–
–
12.7
MHz
CRCPRS
Input clock frequency
(CRC Mode)
–
–
12.7
MHz
SPIM
Input clock frequency
–
–
6.35
MHz
SPIS
Input clock frequency
Width of SS_ Negated between transmissions
–
–
4.23
MHz
100[26]
–
–
ns
The SPI serial clock (SCLK)
frequency is equal to the input
clock frequency divided by 2.
Transmitter
Input clock frequency
–
–
12.7
MHz
The baud rate is equal to the input
clock frequency divided by 8.
Receiver
Input clock frequency
–
–
12.7
MHz
The baud rate is equal to the input
clock frequency divided by 8.
Note
26. 50 ns minimum input pulse width is based on the input synchronizers running at 12 MHz (84 ns nominal period).
Document Number: 38-12028 Rev. *R
Page 42 of 65
CY8C24123A
CY8C24223A
CY8C24423A
AC Analog Output Buffer Specifications
The following tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to
5.25 V and –40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively.
Typical parameters are measured at 5 V, 3.3 V, and 2.7 V at 25 °C and are for design guidance only.
Table 39. 5-V AC Analog Output Buffer Specifications
Min
Typ
Max
Units
tROB
Symbol
Rising settling time to 0.1%, 1 V Step, 100 pF load
Power = low
Power = high
Description
–
–
–
–
2.5
2.5
µs
µs
tSOB
Falling settling time to 0.1%, 1 V Step, 100 pF load
Power = low
Power = high
–
–
–
–
2.2
2.2
µs
µs
SRROB
Rising slew rate (20% to 80%), 1 V Step, 100 pF load
Power = low
Power = high
0.65
0.65
–
–
–
–
V/µs
V/µs
SRFOB
Falling slew rate (80% to 20%), 1 V Step, 100 pF load
Power = low
Power = high
0.65
0.65
–
–
–
–
V/µs
V/µs
BWOB
Small signal bandwidth, 20mVpp, 3dB BW, 100 pF load
Power = low
Power = high
0.8
0.8
–
–
–
–
MHz
MHz
BWOB
Large signal bandwidth, 1Vpp, 3dB BW, 100 pF load
Power = low
Power = high
300
300
–
–
–
–
kHz
kHz
Table 40. 3.3-V AC Analog Output Buffer Specifications
Min
Typ
Max
Units
tROB
Symbol
Rising settling time to 0.1%, 1 V Step, 100 pF load
Power = low
Power = high
Description
–
–
–
–
3.8
3.8
µs
µs
tSOB
Falling settling time to 0.1%, 1 V Step, 100 pF load
Power = low
Power = high
–
–
–
–
2.6
2.6
µs
µs
SRROB
Rising slew rate (20% to 80%), 1 V Step, 100 pF load
Power = low
Power = high
0.5
0.5
–
–
–
–
V/µs
V/µs
SRFOB
Falling slew rate (80% to 20%), 1 V Step, 100 pF load
Power = low
Power = high
0.5
0.5
–
–
–
–
V/µs
V/µs
BWOB
Small signal bandwidth, 20mVpp, 3dB BW, 100 pF load
Power = low
Power = high
0.7
0.7
–
–
–
–
MHz
MHz
BWOB
Large signal bandwidth, 1Vpp, 3dB BW, 100 pF load
Power = low
Power = high
200
200
–
–
–
–
kHz
kHz
Document Number: 38-12028 Rev. *R
Page 43 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Table 41. 2.7-V AC Analog Output Buffer Specifications
Min
Typ
Max
Units
tROB
Symbol
Rising settling time to 0.1%, 1 V Step, 100 pF load
Power = low
Power = high
Description
–
–
–
–
4
4
µs
µs
tSOB
Falling settling time to 0.1%, 1 V Step, 100 pF load
Power = low
Power = high
–
–
–
–
3
3
µs
µs
SRROB
Rising slew rate (20% to 80%), 1 V Step, 100 pF load
Power = low
Power = high
0.4
0.4
–
–
–
–
V/µs
V/µs
SRFOB
Falling slew rate (80% to 20%), 1 V Step, 100 pF load
Power = low
Power = high
0.4
0.4
–
–
–
–
V/µs
V/µs
BWOB
Small signal bandwidth, 20 mVpp, 3dB BW, 100 pF load
Power = low
Power = high
0.6
0.6
–
–
–
–
MHz
MHz
BWOB
Large signal bandwidth, 1 Vpp, 3dB BW, 100 pF load
Power = low
Power = high
180
180
–
–
–
–
kHz
kHz
AC External Clock Specifications
The following tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to
5.25 V and –40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively.
Typical parameters are measured at 5 V, 3.3 V, and 2.7 V at 25 °C and are for design guidance only.
Table 42. 5-V AC External Clock Specifications
Symbol
FOSCEXT
Description
Frequency
Min
Typ
Max
Units
0.093
–
24.6
MHz
ns
–
High period
20.6
–
5300
–
Low period
20.6
–
–
ns
–
Power-up IMO to switch
150
–
–
s
Table 43. 3.3-V AC External Clock Specifications
Min
Typ
Max
Units
FOSCEXT
Symbol
Frequency with CPU clock divide by 1[27]
Description
0.093
–
12.3
MHz
FOSCEXT
Frequency with CPU clock divide by 2 or greater[28]
0.186
–
24.6
MHz
–
High period with CPU clock divide by 1
41.7
–
5300
ns
–
Low period with CPU clock divide by 1
41.7
–
–
ns
–
Power-up IMO to switch
150
–
–
s
Notes
27. Maximum CPU frequency is 12 MHz at 3.3 V. With the CPU clock divider set to 1, the external clock must adhere to the maximum frequency and duty cycle
requirements.
28. If the frequency of the external clock is greater than 12 MHz, the CPU clock divider must be set to 2 or greater. In this case, the CPU clock divider ensures that the
fifty percent duty cycle requirement is met
Document Number: 38-12028 Rev. *R
Page 44 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Table 44. 2.7-V AC External Clock Specifications
Min
Typ
Max
Units
FOSCEXT
Symbol
Frequency with CPU clock divide by 1[29]
Description
0.093
–
12.3
MHz
FOSCEXT
Frequency with CPU clock divide by 2 or greater[30]
0.186
–
12.3
MHz
ns
–
High period with CPU clock divide by 1
41.7
–
5300
–
Low period with CPU clock divide by 1
41.7
–
–
ns
–
Power-up IMO to switch
150
–
–
µs
Notes
AC Programming Specifications
Table 45 lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively. Typical parameters
are measured at 5 V, 3.3 V, and 2.7 V at 25 °C and are for design guidance only.
Table 45. AC Programming Specifications
Symbol
Description
Min
Typ
Max
Units
1
–
20
ns
Fall time of SCLK
1
–
20
ns
Data setup time to falling edge of SCLK
40
–
–
ns
tHSCLK
Data hold time from falling edge of SCLK
40
–
–
ns
FSCLK
Frequency of SCLK
0
–
8
MHz
tERASEB
Flash erase time (block)
–
20
–
ms
tWRITE
Flash block write time
–
80
–
ms
tDSCLK
Data out delay from falling edge of SCLK
–
–
45
ns
VDD  3.6
tDSCLK3
Data out delay from falling edge of SCLK
–
–
50
ns
3.0  VDD  3.6
tDSCLK2
Data out delay from falling edge of SCLK
–
–
70
ns
2.4  VDD  3.0
tERASEALL
Flash erase time (Bulk)
–
20
–
ms
Erase all blocks and
protection fields at once
tPROGRAM_HOT
Flash block erase + flash block write time
–
–
200[31]
ms
0 °C  Tj  100 °C
tPROGRAM_COLD
Flash block erase + flash block write time
–
–
400[31]
ms
–40 °C  Tj  0 °C
tRSCLK
Rise time of SCLK
tFSCLK
tSSCLK
Notes
Notes
29. Maximum CPU frequency is 12 MHz at 3.3 V. With the CPU clock divider set to 1, the external clock must adhere to the maximum frequency and duty cycle
requirements.
30. If the frequency of the external clock is greater than 12 MHz, the CPU clock divider must be set to 2 or greater. In this case, the CPU clock divider ensures that the
fifty percent duty cycle requirement is met.
31. For the full industrial range, you must employ a temperature sensor user module (FlashTemp) and feed the result to the temperature argument before writing.
Refer to the Flash APIs application note Design Aids – Reading and Writing PSoC® Flash – AN2015 for more information.
Document Number: 38-12028 Rev. *R
Page 45 of 65
CY8C24123A
CY8C24223A
CY8C24423A
AC I2C Specifications
The following tables list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to
5.25 V and –40 °C  TA  85 °C, 3.0 V to 3.6 V and –40 °C  TA  85 °C, or 2.4 V to 3.0 V and –40 °C  TA  85 °C, respectively.
Typical parameters are measured at 5 V, 3.3 V, and 2.7 V at 25 °C and are for design guidance only.
Table 46. AC Characteristics of the I2C SDA and SCL Pins for VDD > 3.0 V
Symbol
FSCLI2C
tHDSTAI2C
tLOWI2C
tHIGHI2C
tSUSTAI2C
tHDDATI2C
tSUDATI2C
tSUSTOI2C
tBUFI2C
tSPI2C
Description
SCL clock frequency
Hold time (repeated) start condition. After this period, the first clock
pulse is generated
Low period of the SCL clock
High period of the SCL clock
Setup time for a repeated start condition
Data hold time
Data setup time
Setup time for stop condition
Bus free time between a stop and start condition
Pulse width of spikes are suppressed by the input filter
Standard-Mode
Min
Max
0
100
4.0
–
4.7
4.0
4.7
0
250
4.0
4.7
–
–
–
–
–
–
–
–
–
Fast-Mode
Min
Max
0
400
0.6
–
1.3
0.6
0.6
0
100[32]
0.6
1.3
0
Units
kHz
µs
–
–
–
–
–
–
–
50
µs
µs
µs
µs
ns
µs
µs
ns
Table 47. AC Characteristics of the I2C SDA and SCL Pins for VDD 3.0 V (Fast Mode Not Supported)
Symbol
Standard-Mode
Description
Fast-Mode
Units
Min
Max
Min
Max
0
100
–
–
kHz
4.0
–
–
–
µs
FSCLI2C
SCL clock frequency
tHDSTAI2C
Hold time (repeated) start condition. After this period, the first clock
pulse is generated
tLOWI2C
Low period of the SCL clock
4.7
–
–
–
µs
tHIGHI2C
High period of the SCL clock
4.0
–
–
–
µs
tSUSTAI2C
Setup time for a repeated start condition
4.7
–
–
–
µs
tHDDATI2C
Data hold time
0
–
–
–
µs
tSUDATI2C
Data setup time
250
–
–
–
ns
tSUSTOI2C
Setup time for stop condition
4.0
–
–
–
µs
tBUFI2C
Bus free time between a stop and start condition
4.7
–
–
–
µs
tSPI2C
Pulse width of spikes are suppressed by the input filter
–
–
–
–
ns
Figure 15. Definition for Timing for Fast-/Standard-Mode on the
I2C
Bus
I2C_SDA
TSUDATI2C
THDSTAI2C
TSPI2C
THDDATI2CTSUSTAI2C
TBUFI2C
I2C_SCL
THIGHI2C TLOWI2C
S
START Condition
TSUSTOI2C
Sr
Repeated START Condition
P
S
STOP Condition
Note
32. A fast-mode I2C-bus device can be used in a Standard-Mode I2C-bus system, but the requirement tSUDAT  250 ns must then be met. This is automatically the case
if the device does not stretch the LOW period of the SCL signal. If such device does stretch the LOW period of the SCL signal, it must output the next data bit to the
SDA line trmax + tSUDAT = 1000 + 250 = 1250 ns (according to the Standard-Mode I2C-bus specification) before the SCL line is released.
Document Number: 38-12028 Rev. *R
Page 46 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Packaging Information
This section illustrates the packaging specifications for the CY8C24x23A PSoC device, along with the thermal impedances for each
package and the typical package capacitance on crystal pins.
Important Note Emulation tools may require a larger area on the target PCB than the chip's footprint. For a detailed description of
the emulation tools' dimensions, see the emulator pod drawings at http://www.cypress.com/design/MR10161.
Packaging Dimensions
Figure 16. 8-Pin (300-Mil) PDIP
51-85075 *C
Document Number: 38-12028 Rev. *R
Page 47 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Figure 17. 8-Pin (150-Mil) SOIC
51-85066 *E
Figure 18. 20-Pin (300-Mil) Molded DIP
51-85011 *C
Document Number: 38-12028 Rev. *R
Page 48 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Figure 19. 20-Pin (210-Mil) SSOP
51-85077 *E
Document Number: 38-12028 Rev. *R
Page 49 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Figure 20. 20-Pin (300-Mil) Molded SOIC
51-85024 *E
Figure 21. 28-Pin (300-Mil) Molded DIP
51-85014 *F
Document Number: 38-12028 Rev. *R
Page 50 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Figure 22. 28-Pin (210-Mil) SSOP
51-85079 *E
Figure 23. 28-Pin (300-Mil) Molded SOIC
51-85026 *F
Document Number: 38-12028 Rev. *R
Page 51 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Figure 24. 32-Pin Sawn QFN Package
001-30999 *C
Important Note For information on the preferred dimensions for mounting QFN packages, see the application note, Application Notes
for Surface Mount Assembly of Amkor's MicroLeadFrame (MLF) Packages available at http://www.amkor.com.
Figure 25. 56-Pin (300-Mil) SSOP
51-85062 *E
Document Number: 38-12028 Rev. *R
Page 52 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Thermal Impedances
Capacitance on Crystal Pins
Table 48. Thermal Impedances per Package
Package
Typical JA
Table 49. Typical Package Capacitance on Crystal Pins
[33]
Package
Package Capacitance
8-pin PDIP
123 °C/W
8-pin PDIP
2.8 pF
8-pin SOIC
185 °C/W
8-pin SOIC
2.0 pF
20-pin PDIP
109 °C/W
20-pin PDIP
3.0 pF
20-pin SSOP
117 °C/W
20-pin SSOP
2.6 pF
20-pin SOIC
81 °C/W
20-pin SOIC
2.5 pF
28-pin PDIP
69 °C/W
28-pin PDIP
3.5 pF
28-pin SSOP
101 °C/W
28-pin SSOP
2.8 pF
28-pin SOIC
74 °C/W
28-pin SOIC
2.7 pF
32-pin QFN[34]
22 °C/W
32-pin QFN
2.0 pF
Solder Reflow Specifications
Table 50 shows the solder reflow temperature limits that must not be exceeded.
Table 50. Solder Reflow Specifications
Maximum Peak
Temperature (TC)
Maximum Time
above TC – 5 °C
8-pin PDIP
260 °C
30 seconds
8-pin SOIC
260 °C
30 seconds
20-pin PDIP
260 °C
30 seconds
20-pin SSOP
260 °C
30 seconds
20-pin SOIC
260 °C
30 seconds
28-pin PDIP
260 °C
30 seconds
28-pin SSOP
260 °C
30 seconds
28-pin SOIC
260 °C
30 seconds
32-pin QFN
260 °C
30 seconds
Package
Notes
33. TJ = TA + Power × JA
34. To achieve the thermal impedance specified for the QFN package, refer to Application Notes for Surface Mount Assembly of Amkor's MicroLeadFrame (MLF) Packages
available at www.amkor.com.
Document Number: 38-12028 Rev. *R
Page 53 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Development Tool Selection
This section presents the development tools available for all
current PSoC device families including the CY8C24x23A family.
Software
PSoC Designer
CY3210-MiniProg1
The CY3210-MiniProg1 kit lets you to program PSoC devices
through the MiniProg1 programming unit. The MiniProg is a
small, compact prototyping programmer that connects to the PC
through a provided USB 2.0 cable. The kit includes:
At the core of the PSoC development software suite is
PSoC Designer, used to generate PSoC firmware applications.
PSoC Designer is available free of charge at
http://www.cypress.com and includes a free C compiler.
■
MiniProg programming unit
■
MiniEval socket programming and evaluation board
■
28-pin CY8C29466-24PXI PDIP PSoC device sample
PSoC Programmer
■
28-pin CY8C27443-24PXI PDIP PSoC device sample
Flexible enough to be used on the bench in development, yet
suitable for factory programming, PSoC Programmer works
either as a standalone programming application or it can operate
directly from PSoC Designer. PSoC Programmer software is
compatible with both PSoC ICE-Cube In-Circuit Emulator and
PSoC MiniProg. PSoC programmer is available free ofcharge at
http://www.cypress.com.
■
PSoC Designer software CD
■
Getting Started guide
■
USB 2.0 cable
Development Kits
All development kits can be purchased from the Cypress Online
Store.
CY3215-DK Basic Development Kit
The CY3215-DK is for prototyping and development with
PSoC Designer. This kit supports in-circuit emulation and the
software interface lets you to run, halt, and single step the
processor and view the content of specific memory locations.
Advance emulation features also supported through PSoC
Designer. The kit includes:
CY3210-PSoCEval1
The CY3210-PSoCEval1 kit features an evaluation board and
the MiniProg1 programming unit. The evaluation board includes
an LCD module, potentiometer, LEDs, and plenty of breadboarding space to meet all of your evaluation needs. The kit
includes:
■ Evaluation board with LCD module
■ MiniProg programming unit
■ 28-pin CY8C29466-24PXI PDIP PSoC device sample (2)
■ PSoC Designer software CD
■ Getting Started guide
■ USB 2.0 cable
■
PSoC Designer software CD
CY3214-PSoCEvalUSB
■
ICE-Cube in-circuit emulator
■
ICE Flex-Pod for CY8C29x66 family
■
Cat-5 adapter
■
Mini-Eval programming board
■
110 ~ 240 V power supply, Euro-Plug adapter
■
iMAGEcraft C compiler (registration required)
■
ISSP cable
■
USB 2.0 cable and Blue Cat-5 cable
■
2 CY8C29466-24PXI 28-PDIP chip samples
The CY3214-PSoCEvalUSB evaluation kit features a
development board for the CY8C24794-24LFXI PSoC device.
Special features of the board include both USB and capacitive
sensing development and debugging support. This evaluation
board also includes an LCD module, potentiometer, LEDs, an
enunciator and plenty of bread boarding space to meet all of your
evaluation needs. The kit includes:
■ PSoCEvalUSB board
■ LCD module
■ MIniProg programming unit
■ Mini USB cable
■ PSoC Designer and Example Projects CD
■ Getting Started guide
■ Wire pack
Evaluation Tools
All evaluation tools can be purchased from the Cypress Online
Store.
Document Number: 38-12028 Rev. *R
Page 54 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Device Programmers
All device programmers can be purchased from the Cypress
Online Store.
CY3216 Modular Programmer
The CY3216 Modular Programmer kit features a modular
programmer and the MiniProg1 programming unit. The modular
programmer includes three programming module cards and
supports multiple Cypress products. The kit includes:
■ Modular programmer base
■ Three programming module cards
■ MiniProg programming unit
■ PSoC Designer software CD
■ Getting Started guide
■ USB 2.0 cable
CY3207ISSP In-System Serial Programmer (ISSP)
The CY3207ISSP is a production programmer. It includes
protection circuitry and an industrial case that is more robust than
the MiniProg in a production-programming environment.
Note CY3207ISSP needs special software and is not compatible
with PSoC Programmer. The kit includes:
■
CY3207 programmer unit
■
PSoC ISSP software CD
■
110 ~ 240 V power supply, Euro-Plug adapter
■
USB 2.0 cable
Accessories (Emulation and Programming)
Table 51. Emulation and Programming Accessories
Part Number
All non-QFN
Pin Package
All non-QFN
Flex-Pod Kit[35]
CY3250-24X23A
Foot Kit[36]
CY3250-8DIP-FK,
CY3250-8SOIC-FK,
CY3250-20DIP-FK,
CY3250-20SOIC-FK,
CY3250-20SSOP-FK,
CY3250-28DIP-FK,
CY3250-28SOIC-FK,
CY3250-28SSOP-FK
Adapter[37]
Adapters can be found at
http://www.emulation.com.
Notes
35. Flex-Pod kit includes a practice flex-pod and a practice PCB, in addition to two flex-pods.
36. Foot kit includes surface mount feet that can be soldered to the target PCB.
37. Programming adapter converts non-DIP package to DIP footprint. Specific details and ordering information for each of the adapters can be found at
http://www.emulation.com.
Document Number: 38-12028 Rev. *R
Page 55 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Ordering Information
CY8C24423A-24SXI
CY8C24423A-24SXIT
CY8C24423A-24LTXI
CY8C24423A-24LTXIT
CY8C24000A-24PVXI[38]
XRES Pin
CY8C24423A-24PVXIT
Analog Outputs
CY8C24423A-24PXI
CY8C24423A-24PVXI
Analog Inputs
CY8C24223A-24SXIT
Digital I/O Pins
CY8C24223A-24SXI
Analog Blocks
CY8C24223A-24PVXIT
Digital Blocks
CY8C24223A-24PXI
CY8C24223A-24PVXI
Temperature
Range
CY8C24123A-24SXIT
Switch Mode
Pump
CY8C24123A-24PXI
CY8C24123A-24SXI
SRAM
(Bytes)
8-pin (300-mil) DIP
8-pin (150-mil) SOIC
8-pin (150-mil) SOIC
(Tape and Reel)
20-pin (300-mil) DIP
20-pin (210-mil) SSOP
20-pin (210-mil) SSOP
(Tape and Reel)
20-pin (300-mil) SOIC
20-pin (300-mil) SOIC
(Tape and Reel)
28-pin (300-mil) DIP
28-pin (210-mil) SSOP
28-pin (210-mil) SSOP
(Tape and Reel)
28-pin (300-mil) SOIC
28-pin (300-mil) SOIC
(Tape and Reel)
32-pin (5 × 5 mm 1.00 max)
Sawn QFN
32-pin (5 × 5 mm 1.00 max)
Sawn QFN (Tape and Reel)
56-pin OCD SSOP
Flash
(Bytes)
Package
Ordering
Code
The following table lists the CY8C24x23A PSoC device’s key package features and ordering codes.
Table 52. CY8C24x23A PSoC Device Key Features and Ordering Information
4K
4K
4K
256
256
256
No
No
No
–40 °C to +85 °C
–40 °C to +85 °C
–40 °C to +85 °C
4
4
4
6
6
6
6
6
6
4
4
4
2
2
2
No
No
No
4K
4K
4K
256
256
256
Yes
Yes
Yes
–40 °C to +85 °C
–40 °C to +85 °C
–40 °C to +85 °C
4
4
4
6
6
6
16
16
16
8
8
8
2
2
2
Yes
Yes
Yes
4K
4K
256
256
Yes
Yes
–40 °C to +85 °C
–40 °C to +85 °C
4
4
6
6
16
16
8
8
2
2
Yes
Yes
4K
4K
4K
256
256
256
Yes
Yes
Yes
–40 °C to +85 °C
–40 °C to +85 °C
–40 °C to +85 °C
4
4
4
6
6
6
24
24
24
10
10
10
2
2
2
Yes
Yes
Yes
4K
4K
256
256
Yes
Yes
–40 °C to +85 °C
–40 °C to +85 °C
4
4
6
6
24
24
10
10
2
2
Yes
Yes
4K
256
Yes
–40 °C to +85 °C
4
6
24
10
2
Yes
4K
256
Yes
–40 °C to +85 °C
4
6
24
10
2
Yes
4K
256
Yes
–40 °C to +85 °C
4
6
24
10
2
Yes
Note For Die sales information, contact a local Cypress sales office or Field Applications Engineer (FAE).
Ordering Code Definitions
CY 8 C 24 xxx-SPxx
Package Type:
PX = PDIP Pb-free
SX = SOIC Pb-free
PVX = SSOP Pb-free
LFX/LKX = QFN Pb-free
AX = TQFP Pb-Free
Thermal Rating:
C = Commercial
I = Industrial
E = Extended
Speed: 24 MHz
Part Number
Family Code
Technology Code: C = CMOS
Marketing Code: 8 = Cypress PSoC
Company ID: CY = Cypress
Note
38. This part may be used for in-circuit debugging. It is NOT available for production.
Document Number: 38-12028 Rev. *R
Page 56 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Acronyms
Acronyms Used
Table 53 lists the acronyms that are used in this document.
Table 53. Acronyms Used in this Datasheet
Acronym
AC
Description
Acronym
Description
alternating current
MIPS
million instructions per second
ADC
analog-to-digital converter
OCD
on-chip debug
API
application programming interface
PCB
printed circuit board
complementary metal oxide semiconductor
PDIP
plastic dual-in-line package
CPU
central processing unit
PGA
programmable gain amplifier
CRC
cyclic redundancy check
PLL
phase-locked loop
continuous time
POR
power on reset
CMOS
CT
DAC
DC
digital-to-analog converter
direct current
PPOR
PRS
precision power on reset
pseudo-random sequence
DTMF
dual-tone multi-frequency
PSoC®
ECO
external crystal oscillator
PWM
pulse width modulator
electrically erasable programmable read-only
memory
QFN
quad flat no leads
real time clock
EEPROM
GPIO
general purpose I/O
RTC
ICE
in-circuit emulator
SAR
IDE
integrated development environment
SC
SLIMO
Programmable System-on-Chip
successive approximation
switched capacitor
ILO
internal low speed oscillator
IMO
internal main oscillator
SMP
slow IMO
switch mode pump
I/O
input/output
SOIC
small-outline integrated circuit
IrDA
infrared data association
SPITM
serial peripheral interface
ISSP
in-system serial programming
SRAM
static random access memory
LCD
liquid crystal display
SROM
supervisory read only memory
LED
light-emitting diode
SSOP
shrink small-outline package
LPC
low power comparator
UART
universal asynchronous receiver / transmitter
LVD
low voltage detect
USB
MAC
multiply-accumulate
WDT
universal serial bus
watchdog timer
MCU
microcontroller unit
XRES
external reset
Reference Documents
CY8CPLC20, CY8CLED16P01, CY8C29x66, CY8C27x43, CY8C24x94, CY8C24x23, CY8C24x23A, CY8C22x13, CY8C21x34,
CY8C21x23, CY7C64215, CY7C603xx, CY8CNP1xx, and CYWUSB6953 PSoC® Programmable System-on-Chip Technical
Reference Manual (TRM) (001-14463)
Design Aids – Reading and Writing PSoC® Flash – AN2015 (001-40459)
Adjusting PSoC® Trims for 3.3 V and 2.7 V Operation – AN2012 (001-17397)
Understanding Datasheet Jitter Specifications for Cypress Timing Products – AN5054 (001-14503)
Application Notes for Surface Mount Assembly of Amkor's MicroLeadFrame (MLF) Packages – available at http://www.amkor.com.
Document Number: 38-12028 Rev. *R
Page 57 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Document Conventions
Units of Measure
Table 54 lists the unit sof measures.
Table 54. Units of Measure
Symbol
Unit of Measure
Symbol
Unit of Measure
kB
1024 bytes
µs
microsecond
dB
decibels
ms
millisecond
°C
degree Celsius
ns
nanosecond
fF
femto farad
ps
picosecond
pF
picofarad
µV
microvolts
kHz
kilohertz
MHz
megahertz
mVpp
rt-Hz
mV
millivolts
millivolts peak-to-peak
root hertz
nV
nanovolts
k
kilohm
V
volts

ohm
µW
microwatts
W
watt
µA
microampere
mA
milliampere
mm
millimeter
nA
nanoampere
ppm
parts per million
pA
pikoampere
%
mH
millihenry
percent
Numeric Conventions
Hexadecimal numbers are represented with all letters in uppercase with an appended lowercase ‘h’ (for example, ‘14h’ or ‘3Ah’).
Hexadecimal numbers may also be represented by a ‘0x’ prefix, the C coding convention. Binary numbers have an appended
lowercase ‘b’ (for example, 01010100b’ or ‘01000011b’). Numbers not indicated by an ‘h’ or ‘b’ are decimals.
Glossary
active high
5. A logic signal having its asserted state as the logic 1 state.
6. A logic signal having the logic 1 state as the higher voltage of the two states.
analog blocks
The basic programmable opamp circuits. These are SC (switched capacitor) and CT (continuous
time) blocks. These blocks can be interconnected to provide ADCs, DACs, multi-pole filters, gain
stages, and much more.
analog-to-digital
(ADC)
A device that changes an analog signal to a digital signal of corresponding magnitude. Typically,
an ADC converts a voltage to a digital number. The digital-to-analog (DAC) converter performs
the reverse operation.
API (Application
Programming
Interface)
A series of software routines that comprise an interface between a computer application and
lower level services and functions (for example, user modules and libraries). APIs serve as
building blocks for programmers that create software applications.
asynchronous
A signal whose data is acknowledged or acted upon immediately, irrespective of any clock signal.
Bandgap
reference
A stable voltage reference design that matches the positive temperature coefficient of VT with
the negative temperature coefficient of VBE, to produce a zero temperature coefficient (ideally)
reference.
Document Number: 38-12028 Rev. *R
Page 58 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Glossary
(continued)
bandwidth
1. The frequency range of a message or information processing system measured in hertz.
2. The width of the spectral region over which an amplifier (or absorber) has substantial gain (or
loss); it is sometimes represented more specifically as, for example, full width at half maximum.
bias
1. A systematic deviation of a value from a reference value.
2. The amount by which the average of a set of values departs from a reference value.
3. The electrical, mechanical, magnetic, or other force (field) applied to a device to establish a
reference level to operate the device.
block
1. A functional unit that performs a single function, such as an oscillator.
2. A functional unit that may be configured to perform one of several functions, such as a digital
PSoC block or an analog PSoC block.
buffer
1. A storage area for data that is used to compensate for a speed difference, when transferring
data from one device to another. Usually refers to an area reserved for IO operations, into
which data is read, or from which data is written.
2. A portion of memory set aside to store data, often before it is sent to an external device or as
it is received from an external device.
3. An amplifier used to lower the output impedance of a system.
bus
1. A named connection of nets. Bundling nets together in a bus makes it easier to route nets
with similar routing patterns.
2. A set of signals performing a common function and carrying similar data. Typically represented
using vector notation; for example, address[7:0].
3. One or more conductors that serve as a common connection for a group of related devices.
clock
The device that generates a periodic signal with a fixed frequency and duty cycle. A clock is
sometimes used to synchronize different logic blocks.
comparator
An electronic circuit that produces an output voltage or current whenever two input levels simultaneously
satisfy predetermined amplitude requirements.
compiler
A program that translates a high level language, such as C, into machine language.
configuration
space
In PSoC devices, the register space accessed when the XIO bit, in the CPU_F register,
is set to ‘1’.
crystal oscillator
An oscillator in which the frequency is controlled by a piezoelectric crystal. Typically a piezoelectric
crystal is less sensitive to ambient temperature than other circuit components.
cyclic redundancy A calculation used to detect errors in data communications, typically performed using a linear
check (CRC)
feedback shift register. Similar calculations may be used for a variety of other purposes such as
data compression.
data bus
A bi-directional set of signals used by a computer to convey information from a memory location
to the central processing unit and vice versa. More generally, a set of signals used to convey
data between digital functions.
debugger
A hardware and software system that allows the user to analyze the operation of the system
under development. A debugger usually allows the developer to step through the firmware one
step at a time, set break points, and analyze memory.
dead band
A period of time when neither of two or more signals are in their active state or in transition.
Document Number: 38-12028 Rev. *R
Page 59 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Glossary
(continued)
digital blocks
The 8-bit logic blocks that can act as a counter, timer, serial receiver, serial transmitter, CRC
generator, pseudo-random number generator, or SPI.
digital-to-analog
(DAC)
A device that changes a digital signal to an analog signal of corresponding magnitude. The analogto-digital (ADC) converter performs the reverse operation.
duty cycle
The relationship of a clock period high time to its low time, expressed as a percent.
emulator
Duplicates (provides an emulation of) the functions of one system with a different system, so that
the second system appears to behave like the first system.
external reset
(XRES)
An active high signal that is driven into the PSoC device. It causes all operation of the CPU and
blocks to stop and return to a pre-defined state.
flash
An electrically programmable and erasable, non-volatile technology that provides users with the
programmability and data storage of EPROMs, plus in-system erasability. Non-volatile means
that the data is retained when power is off.
Flash block
The smallest amount of Flash ROM space that may be programmed at one time and the smallest
amount of Flash space that may be protected. A Flash block holds 64 bytes.
frequency
The number of cycles or events per unit of time, for a periodic function.
gain
The ratio of output current, voltage, or power to input current, voltage, or power, respectively.
Gain is usually expressed in dB.
I2C
A two-wire serial computer bus by Philips Semiconductors (now NXP Semiconductors). I2C is an
Inter-Integrated Circuit. It is used to connect low-speed peripherals in an embedded system. The
original system was created in the early 1980s as a battery control interface, but it was later used
as a simple internal bus system for building control electronics. I2C uses only two bi-directional
pins, clock and data, both running at +5V and pulled high with resistors. The bus operates at 100
kbits/second in standard mode and 400 kbits/second in fast mode.
ICE
The in-circuit emulator that allows users to test the project in a hardware environment, while
viewing the debugging device activity in a software environment (PSoC Designer).
input/output (I/O) A device that introduces data into or extracts data from a system.
interrupt
A suspension of a process, such as the execution of a computer program, caused by an event
external to that process, and performed in such a way that the process can be resumed.
interrupt service
routine (ISR)
A block of code that normal code execution is diverted to when the M8C receives a hardware
interrupt. Many interrupt sources may each exist with its own priority and individual ISR code
block. Each ISR code block ends with the RETI instruction, returning the device to the point in
the program where it left normal program execution.
jitter
1. A misplacement of the timing of a transition from its ideal position. A typical form of corruption that occurs on
serial data streams.
2. The abrupt and unwanted variations of one or more signal characteristics, such as the interval between
successive pulses, the amplitude of successive cycles, or the frequency or phase of successive cycles.
low-voltage detect A circuit that senses VDD and provides an interrupt to the system when VDD falls lower than a
(LVD)
selected threshold.
Document Number: 38-12028 Rev. *R
Page 60 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Glossary
(continued)
M8C
An 8-bit Harvard-architecture microprocessor. The microprocessor coordinates all activity inside
a PSoC by interfacing to the Flash, SRAM, and register space.
master device
A device that controls the timing for data exchanges between two devices. Or when devices are
cascaded in width, the master device is the one that controls the timing for data exchanges
between the cascaded devices and an external interface. The controlled device is called the
slave device.
microcontroller
An integrated circuit chip that is designed primarily for control systems and products. In addition
to a CPU, a microcontroller typically includes memory, timing circuits, and IO circuitry. The reason
for this is to permit the realization of a controller with a minimal quantity of chips, thus
achieving maximal possible miniaturization. This in turn, reduces the volume and the cost of
the controller. The microcontroller is normally not used for general-purpose computation as is a
microprocessor.
mixed-signal
The reference to a circuit containing both analog and digital techniques and components.
modulator
A device that imposes a signal on a carrier.
noise
1. A disturbance that affects a signal and that may distort the information carried by the signal.
2. The random variations of one or more characteristics of any entity such as voltage, current, or data.
oscillator
A circuit that may be crystal controlled and is used to generate a clock frequency.
parity
A technique for testing transmitting data. Typically, a binary digit is added to the data to make the
sum of all the digits of the binary data either always even (even parity) or always odd (odd parity).
phase-locked
loop (PLL)
An electronic circuit that controls an oscillator so that it maintains a constant phase angle relative
to a reference signal.
pinouts
The pin number assignment: the relation between the logical inputs and outputs of the PSoC
device and their physical counterparts in the printed circuit board (PCB) package. Pinouts
involve pin numbers as a link between schematic and PCB design (both being computer generated
files) and may also involve pin names.
port
A group of pins, usually eight.
power on reset
(POR)
A circuit that forces the PSoC device to reset when the voltage is lower than a pre-set level. This is
one type of hardware reset.
PSoC®
Cypress Semiconductor’s PSoC® is a registered trademark and Programmable System-onChip™ is a trademark of Cypress.
PSoC Designer™ The software for Cypress’ Programmable System-on-Chip technology.
pulse width
An output in the form of duty cycle which varies as a function of the applied measurand
modulator (PWM)
RAM
An acronym for random access memory. A data-storage device from which data can be read out
and new data can be written in.
register
A storage device with a specific capacity, such as a bit or byte.
reset
A means of bringing a system back to a know state. See hardware reset and software reset.
Document Number: 38-12028 Rev. *R
Page 61 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Glossary
(continued)
ROM
An acronym for read only memory. A data-storage device from which data can be read out, but
new data cannot be written in.
serial
1. Pertaining to a process in which all events occur one after the other.
2. Pertaining to the sequential or consecutive occurrence of two or more related activities in a single device or
channel.
settling time
The time it takes for an output signal or value to stabilize after the input has changed from one
value to another.
shift register
A memory storage device that sequentially shifts a word either left or right to output a stream of
serial data.
slave device
A device that allows another device to control the timing for data exchanges between two
devices. Or when devices are cascaded in width, the slave device is the one that allows another
device to control the timing of data exchanges between the cascaded devices and an external
interface. The controlling device is called the master device.
SRAM
An acronym for static random access memory. A memory device allowing users to store and
retrieve data at a high rate of speed. The term static is used because, after a value has been
loaded into an SRAM cell, it remains unchanged until it is explicitly altered or until power is
removed from the device.
SROM
An acronym for supervisory read only memory. The SROM holds code that is used to boot the
device, calibrate circuitry, and perform Flash operations. The functions of the SROM may be
accessed in normal user code, operating from Flash.
stop bit
A signal following a character or block that prepares the receiving device to receive the next
character or block.
synchronous
1. A signal whose data is not acknowledged or acted upon until the next active edge of a clock signal.
2. A system whose operation is synchronized by a clock signal.
tri-state
A function whose output can adopt three states: 0, 1, and Z (high-impedance). The function does
not drive any value in the Z state and, in many respects, may be considered to be disconnected
from the rest of the circuit, allowing another output to drive the same net.
UART
A UART or universal asynchronous receiver-transmitter translates between parallel bits of data
and serial bits.
user modules
Pre-build, pre-tested hardware/firmware peripheral functions that take care of managing and
configuring the lower level Analog and Digital PSoC Blocks. User Modules also provide high
level API (Application Programming Interface) for the peripheral function.
user space
The bank 0 space of the register map. The registers in this bank are more likely to be modified
during normal program execution and not just during initialization. Registers in bank 1 are most
likely to be modified only during the initialization phase of the program.
VDD
A name for a power net meaning "voltage drain." The most positive power supply signal. Usually
5 V or 3.3 V.
VSS
A name for a power net meaning "voltage source." The most negative power supply signal.
watchdog timer
A timer that must be serviced periodically. If it is not serviced, the CPU resets after a specified
period of time.
Document Number: 38-12028 Rev. *R
Page 62 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Document History Page
Document Title: CY8C24123A, CY8C24223A, CY8C24423A PSoC® Programmable System-on-Chip
Document Number: 38-12028
Revision
ECN
Orig. of
Change
Submission Date
**
236409
SFV
See ECN
New silicon and new document – Preliminary datasheet.
*A
247589
SFV
See ECN
Changed the title to read “Final” datasheet. Updated Electrical Specifications
chapter.
Description of Change
*B
261711
HMT
See ECN
Input all SFV memo changes. Updated Electrical Specifications chapter.
*C
279731
HMT
See ECN
Update Electrical Specifications chapter, including 2.7 VIL DC GPIO spec. Add
Solder Reflow Peak Temperature table. Clean up pinouts and fine tune wording
and format throughout.
*D
352614
HMT
See ECN
Add new color and CY logo. Add URL to preferred dimensions for mounting MLF
packages. Update Transmitter and Receiver AC Digital Block Electrical Specifications. Re-add ISSP pinout identifier. Delete Electrical Specification sentence
re: devices running at greater than 12 MHz. Update Solder Reflow Peak Temperature table. Fix CY.com URLs. Update CY copyright.
*E
424036
HMT
See ECN
Fix SMP 8-pin SOIC error in Feature and Order table. Update 32-pin QFN E-Pad
dimensions and rev. *A. Add ISSP note to pinout tables. Update typical and
recommended Storage Temperature per industrial specs. Add OCD
non-production pinout and package diagram. Update CY branding and QFN
convention. Update package diagram revisions.
*F
521439
HMT
See ECN
Add Low Power Comparator (LPC) AC/DC electrical spec. tables. Add new Dev.
Tool section. Add CY8C20x34 to PSoC Device Characteristics table.
*G
2256806
UVS/PYRS
See ECN
Added Sawn pin information.
*H
2425586
DSO/AESA
See ECN
Corrected Ordering Information to include CY8C24423A-24LTXI and
CY8C24423A-24LTXIT
*I
2619935
OGNE/
AESA
12/11/2008 Changed title to “CY8C24123A, CY8C24223A, CY8C24423A PSoC®
Programmable System-on-Chip™”
Updated package diagram 001-30999 to *A.
Added note on digital signaling in DC Analog Reference Specifications on page
25.
Added Die Sales information note to Ordering Information on page 56.
*J
2692871
DPT/PYRS
04/16/2009 Updated Max package thickness for 32-pin QFN package
Formatted Notes
Updated “Getting Started” on page 6
Updated “Development Tools” on page 6 and “Designing with PSoC Designer”
on page 7
*K
2762168
JVY/AESA
06/25/2009 Updated DC GPIO, AC Chip-Level, and AC Programming Specifications as
follows:
Modified FIMO6 and TWRITE specifications.
Replaced TRAMP (time) specification with SRPOWER_UP (slew rate) specification.
Added note [9] to Flash Endurance specification.
Added IOH, IOL, DCILO, F32K_U, TPOWERUP, TERASEALL, TPROGRAM_HOT, and
TPROGRAM_COLD specifications.
Document Number: 38-12028 Rev. *R
Page 63 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Document Title: CY8C24123A, CY8C24223A, CY8C24423A PSoC® Programmable System-on-Chip
Document Number: 38-12028
Revision
ECN
Orig. of
Change
Submission Date
*L
2897881
MAXK/NJF
*M
2942375
VMAD
*N
3032514
NJF
*O
3098766
YJI
12/01/2010 Sunset review; no content update
*P
3351721
YJI
08/31/2011 Full annual review of document. No changes are required.
*Q
3367463
BTK/GIR
*R
3598291 LURE/XZNG 04/24/2012 Changed the PWM description string from “8- to 32-bit” to “8- and 16-bit”.
Description of Change
03/23/2010 Add “Contents” on page 2. Update unit in Table 10-28 and Table 38 of SPIS
Maximum Input Clock Frequency from ns to MHz. Update revision of package
diagrams for 8 PDIP, 8 SOIC, 20 PDIP, 20 SSOP, 20 SOIC, 28 PDIP, 28 SSOP,
28 SOIC, 32 QFN. Updated Cypress website links. Removed reference to PSoC
Designer 4.4. Updated 56-Pin SSOP definitions and diagram. Added TBAKETEMP
and TBAKETIME parameters in Absolute Maximum Ratings. Updated 5-V DC
Analog Reference Specifications table. Updated Note in Packaging Information.
Added Note 29. Updated Solder Reflow Specifications table. Removed Third
Party Tools and Build a PSoC Emulator into your Board. Removed inactive parts
from Ordering Information. Update trademark info. and Sales, Solutions, and
Legal Information.
06/02/2010 Updated content to match current style guide and datasheet template.
No technical updates.
09/17/10
Added PSoC Device Characteristics table.
Added DC I2C Specifications table.
Added F32K_U max limit.
Added Tjit_IMO specification, removed existing jitter specifications.
Updated Analog reference tables.
Updated Units of Measure, Acronyms, Glossary, and References sections.
Updated solder reflow specifications.
No specific changes were made to AC Digital Block Specifications table and I2C
Timing Diagram. They were updated for clearer understanding.
Updated Figure 13 since the labelling for y-axis was incorrect.
Template and styles update.
09/22/2011 Updated text under DC Analog Reference Specifications on page 25.
Removed package diagram spec 51-85188 as there is no active MPN using this
outline drawing.
The text “Pin must be left floating” is included under Description of NC pin in Table
5 on page 11 and Table 6 on page 12.
Updated Table 50 on page 53 to give more clarity.
Removed Footnote #35.
Document Number: 38-12028 Rev. *R
Page 64 of 65
CY8C24123A
CY8C24223A
CY8C24423A
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturers’ representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
Automotive
Clocks & Buffers
Interface
Lighting & Power Control
PSoC Solutions
cypress.com/go/automotive
cypress.com/go/clocks
psoc.cypress.com/solutions
cypress.com/go/interface
PSoC 1 | PSoC 3 | PSoC 5
cypress.com/go/powerpsoc
cypress.com/go/plc
Memory
Optical & Image Sensing
cypress.com/go/memory
cypress.com/go/image
PSoC
Touch Sensing
cypress.com/go/psoc
cypress.com/go/touch
USB Controllers
Wireless/RF
cypress.com/go/USB
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2004-2012. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 38-12028 Rev. *R
Revised April 24, 2012
Page 65 of 65
PSoC Designer™ is a trademark and PSoC® is a registered trademark of Cypress Semiconductor Corporation. All other trademarks or registered trademarks referenced herein are property of the
respective corporations.
Purchase of I2C components from Cypress or one of its sublicensed Associated Companies conveys a license under the Philips I2C Patent Rights to use these components in an I2C system, provided
that the system conforms to the I2C Standard Specification as defined by Philips. As from October 1st, 2006 Philips Semiconductors has a new trade name - NXP Semiconductors.
Similar pages