NEC AC08DSMA 8a resin insulation type triac Datasheet

DATA SHEET
THYRISTORS
AC08DSMA,AC08FSMA
8 A RESIN INSULATION TYPE TRIAC
DESCRIPTION
PACKAGE DRAWING (Unit: mm)
The AC08DSMA and AC08FSMA are resin insulation type
4.7 MAX.
10.5 MAX.
TRIACs with an effective current of 8 A (TC = 88°C).
7 ±0.2
φ 3.2 ±0.2
2.8 ±0.2
1
These products features ratings and electrical characteristics
2 3
5 ±0.2
equal to TO-220AB package TRIAC and a high reliability design.
FEATURES
• Insulation type TRIAC fully covered with resin on the entire
case other than electrode leads
• Insulation voltage and conduction equal to conventional mica
12 ±0.2
mounting.
0.8 ±0.1
1.3 ±0.2
1.5 ±0.2
2.54 TYP.
2.54 TYP.
and polyester film
0.5 ±0.1
2.5 ±0.1
TRIAC
1: T1
2: T2
3: Gate
• Can be replaced with TO-220AB package
• High allowable on-current when using a single unit
*: TC test bench-mark
APPLICATIONS
*
13.5 MIN.
mounting on a heatsink board or performing high-density
17 ±0.2
and are electrically insulated with electrodes, giving them a
considerable advantage over conventional TRIACs when
3.0 MAX.
5 ±0.1
These products are covered with resin mold on the entire case
Standard weight: 2 g
Non-contact switches of motor speed control, heater temperature control, lamp light control
The information in this document is subject to change without notice. Before using this document, please
confirm that this is the latest version.
Not all products and/or types are available in every country. Please check with an NEC Electronics
sales representative for availability and additional information.
Document No. D10613EJ5V0DS00 (5th edition)
Date Published June 2004 NS CP(K)
Printed in Japan
The mark
shows major revised points.
2002
AC08DSMA,AC08FSMA
MAXIMUM RATINGS
Parameter
Symbol
AC08DSMA
AC08FSMA
Unit
Remarks
Non-repetitive Peak Off-state Voltage
VDSM
500
700
V
−
Repetitive Peak Off-state Voltage
VDRM
400
600
V
−
Effective On-state Current
IT(RMS)
8 (TC = 88°C)
A
Refer to Figure 11 and 12.
ITSM
80 (50 Hz 1 cycle)
A
Refer to Figure 2.
Surge On-state Current
88 (60 Hz 1 cycle)
Fusing Current
∫ iT2dt
28 (1 ms ≤ t ≤ 10 ms)
As
2
−
Critical Rate Rise of On-state Current
dIT/dt
50
A/µs
−
PGM
5.0 (f ≥ 50 Hz, Duty ≤ 10%)
W
−
PG(AV)
0.5
W
−
Peak Gate Current
IGM
±3 (f ≥ 50 Hz, Duty ≤ 10%)
A
−
Junction Temperature
Tj
−40~+125
°C
−
Storage Temperature
Tstg
−55~+150
°C
−
Peak Gate Power Dissipation
Average Gate Power Dissipation
ELECTRICAL CHARACTERISTICS (Tj = 25°C)
Parameter
Symbol
Repetitive Peak Off-state Current
On-state Voltage
IDRM
VTM
Gate Trigger Current
VDM = VDRM
TYP.
MAX.
Unit
Remarks
Tj = 25°C
−
−
100
µA
−
Tj = 125°C
−
−
2
mA
−
−
−
1.6
V
Refer to Figure 1.
mA
Refer to Figure 4.
V
Refer to Figure 4.
ITM = 10 A
T2+, G+
−
−
20
RL = 30 Ω
T2−, G+
−
−
−
III
T2−, G−
−
−
20
IV
T2+, G−
−
−
20
VDM = 12 V,
T2+, G+
−
−
1.5
RL = 30 Ω
T2−, G+
−
−
−
T2−, G−
−
−
1.5
IGT
Mode I
VGT
II
III
IV
Gate Non-trigger Voltage
Holding Current
VGD
IH
Critical Rate Rise of Off-state Voltage
Commutating Critical Rate Rise of
dv/dt
T2+, G−
Tj = 125°C, VDM = 1 VDRM
2
−
−
1.5
0.3
−
−
V
−
−
30
−
mA
−
−
100
−
V/µs
−
10
−
−
V/µs
−
−
−
3.7
VDM = 24 V, ITM = 10 A
Tj = 125°C, VDM
2
= 3 VDRM
(dv/dt)c Tj = 125°C,
(diT/dt)c = −4 A/ms, VD = 400 V
Off-state Voltage
Thermal Resistance
MIN.
VDM = 12 V,
Mode I
II
Gate Trigger Voltage
Conditions
Note
Rth(j-c)
Junction-to-case AC
°C/W Refer to Figure 13.
Note The thermal resistance with a 50 Hz or 60 Hz sine wave current, as shown in the following expression:
Rth(j-c) =
Tj (max) − TC
PT ( AV )
Tj(max): Maximum junction temperature
TC: Case temperature
PT(AV): Average on-dissipation
2
Data Sheet D10613EJ5V0DS
AC08DSMA,AC08FSMA
TYPICAL CHARACTERISTICS
Figure 1. iT vs. νT CHARACTERISTIC
Figure 2. ITSM RATING
MAX.
Initial Tj = 125˚C
140
ITSM - Surge On-state Current - A
iT - On-state Current - A
100
10
TC = 125˚C
25˚C
1.0
0.1
ITSM
0
120
100
60 Hz
80
50 Hz
60
40
20
1
2
3
4
5
1
5
νT - On-state Voltage - V
VGT - Gate Trigger Voltage - V
VG - Gate Voltage - V
8
6
PGM = 5 W
f ≥ 50 Hz
Duty ≤ 10%
PG(AV) = 0.5 W
1.0
1.5
2.0
2.5
TA = −40˚C
25˚C
125˚C
1
0.5
0
3.0
0
10
IG - Gate Current - A
10
40
80
40
Mode
I, III, IV
1.4
VGT - Gate Trigger Voltage - V
IGT - Gate Trigger Current - mA
100
0
30
Figure 6. VGT vs. TA CHARACTERISTIC
Mode
I, III, IV
−40
20
IGT - Gate Trigger Current - mA
Figure 5. IGT vs. TA CHARACTERISTIC
1000
1
100
Mode
I, III, IV
1.5
0
0.5
50
Figure 4. GATE CHARACTERISTIC
2.0
Tj = −40 to +125˚C
4
10
Cycles - N
Figure 3. GATE RATING
10
0
2π
0
0
2
π
N=1
1.2
1.0
0.8
0.6
0.4
0.2
120
TA - Ambient Temperature - °C
0
−40
0
40
80
120
TA - Ambient Temperature - °C
Data Sheet D10613EJ5V0DS
3
AC08DSMA,AC08FSMA
Figure 7. iGT vs. τ CHARACTERISTIC
Figure 8. νGT vs. τ CHARACTERISTIC
Mode
I, III, IV
TA = 25˚C
1000
100
10
5
νGT - Gate Trigger Voltage - V
iGT - Gate Trigger Current - mA
10000
1
1
10
100
Mode
I, III, IV
TA = 25˚C
4
3
2
1
0
1000
1
10
τ - Pulse Width - µs
Figure 10. PT(AV) vs. IT(RMS) CHARACTERISTIC
IH - Holding Current - mA
100
10
0
20
40
60
80
100
120
TA - Ambient Temperature - °C
PT(AV) - On-state Average Power Dissipation - W
Figure 9. IH vs. TA CHARACTERISTIC
−20
12
11
10
9
8
7
6
5
4
3
2
1
0
0
1
3
4
5
6
7
8
9
10 11 12
Figure 12. TA vs. IT(RMS) RATING
140
TA - Ambient Temperature - °C
140
TC - Case Temperature - °C
2
IT(RMS) - Effective On-state Current - A
Figure 11. TC vs. IT(RMS) RATING
120
100
80
60
40
20
120
100
80
60
40
20
0
0
0
1
2
3
4
5
6
7
8
9
10 11 12
IT(RMS) - Effective On-state Current - A
4
1000
τ - Pulse Width - µs
1000
1
100
0
1.0
2.0
IT(RMS) - Effective On-state Current - A
Data Sheet D10613EJ5V0DS
AC08DSMA,AC08FSMA
Figure 13. Zth CHARACTERISTIC
Zth - Transient Thermal Impedance - °C/W
100
Junction to ambient
10
Junction to case
1
0.1
0.1
1
10
100
1k
10 k
100 k
Cycles (50 Hz)
Data Sheet D10613EJ5V0DS
5
AC08DSMA,AC08FSMA
• The information in this document is current as of June, 2004. The information is subject to change
without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or
data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all
products and/or types are available in every country. Please check with an NEC Electronics sales
representative for availability and additional information.
• No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may
appear in this document.
• NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual
property rights of third parties by or arising from the use of NEC Electronics products listed in this document
or any other liability arising from the use of such products. No license, express, implied or otherwise, is
granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others.
• Descriptions of circuits, software and other related information in this document are provided for illustrative
purposes in semiconductor product operation and application examples. The incorporation of these
circuits, software and information in the design of a customer's equipment shall be done under the full
responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by
customers or third parties arising from the use of these circuits, software and information.
• While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products,
customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To
minimize risks of damage to property or injury (including death) to persons arising from defects in NEC
Electronics products, customers must incorporate sufficient safety measures in their design, such as
redundancy, fire-containment and anti-failure features.
• NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and
"Specific".
The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC
Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of
each NEC Electronics product before using it in a particular application.
"Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio
and visual equipment, home electronic appliances, machine tools, personal electronic equipment
and industrial robots.
"Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed
for life support).
"Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life
support systems and medical equipment for life support, etc.
The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC
Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications
not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to
determine NEC Electronics' willingness to support a given application.
(Note)
(1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its
majority-owned subsidiaries.
(2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as
defined above).
M8E 02. 11-1
Similar pages