CT CTDD3120DF-1205-D1K-3 Dc/dc converter Datasheet

DC/DC Converters
SPECIFICATIONS
CTDD3120DF-D1K-3 Series
Wide Input Isolated & Regulated
3W Output, Dual Output
Not shown at actual size.
RoHS
Compliant
ctparts.com
Vin
Nom.
(VDC)
Input Range
(VDC)
Vin
Max.*
(VDC)
Vout
(VDC)
CTDD3120DF-1205-D1K-3
CTDD3120DF-1209-D1K-3
CTDD3120DF-1212-D1K-3
CTDD3120DF-1215-D1K-3
12
12
12
12
9-18
9-18
9-18
9-18
22
22
22
22
±5
±9
±12
±15
CTDD3120DF-1505-D1K-3
CTDD3120DF-1509-D1K-3
CTDD3120DF-1512-D1K-3
CTDD3120DF-1515-D1K-3
15
15
15
15
12-24
12-24
12-24
12-24
30
30
30
30
CTDD3120DF-2405-D1K-3
CTDD3120DF-2409-D1K-3
CTDD3120DF-2412-D1K-3
CTDD3120DF-2415-D1K-3
24
24
24
24
18-36
18-36
18-36
18-36
CTDD3120DF-4805-D1K-3
CTDD3120DF-4809-D1K-3
CTDD3120DF-4812-D1K-3
CTDD3120DF-4815-D1K-3
48
48
48
48
36-72
36-72
36-72
36-72
Part
Number
Iout
Max.
(mA)
Iout
Min.
(mA)
Effi.
Typ.
(%)
300
165
125
100
30
16
12
10
72
73
77
79
±5
±9
±12
±15
300
165
125
100
30
16
12
10
75
79
80
81
40
40
40
40
±5
±9
±12
±15
300
165
125
100
30
16
12
10
78
80
81
82
80
80
80
80
±5
±9
±12
±15
300
165
125
100
30
16
12
10
76
81
81
82
*If Input voltage above specified may cause permanent damage to the device
ISOLATION SPECIFICATIONS
Item
Test Condition
MIN
Isolation Voltage
Flash tested for 1 minute
1000
VDC
Test at 500VDC
1000
MΩ
Isolation Resistance
Efficiency: To 82%
Temperature Range: -40°C to +85°C
Isolation: 1KVDC
Package: UL94-V0
Miscellaneous: Wide (2:1) Input Range. Dual Output. No heat
sink required. Pinout compatible with ERICSSON PKV. Continuous
Short Circuit Protection.
Samples available.
CHARACTERISTICS
Output Short Circuit Protection: Continuous
Temperature Rise at Full Load: 30°C (Typ.)
Cooling: Free air convection
No Load, Power Consumption: 100mW (typical)
Operating Temperature Range: -40°C to +85°C
Storage Temperature Range: -55°C to +125°C
Lead Temperature: 300°C (1.5mm from case for 10 seconds)
Storage Humidity Range: < 95%
Case Material: Plastic (UL94-V0)
MTBF: >3,500,000 hours
Miscellaneous: RoHS Compliant.
Test Condition
3W Output Power
Units
TYP
MAX
Units
3
W
Positive voltage accuracy
Refer to Recommended Circuit
±1
±3
%
Negative voltage accuracy
Refer to Recommended Circuit
±3
±5
%
Load regulation
From 10% to 100% load
±0.5
±1
%
Line regulation
Input Voltage from low to high
±0.2
±0.5
%
Temperature drift (Vout)
Refer to Temp. Derating Graph
Ripple
20Hz to 300KHz Bandwidth
Noise
DC-20MHz Bandwidth
Switching frequency
100% load, nominal input voltage
80
Switching frequency
10% load, nominal input voltage
250
0.03
%/°C
30
60
mVp-p
80
150
mVp-p
200
KHz
600
KHz
Note:
1. All specifications measured at TA=25°C, humidity<75%, nominal input voltage and rated output unless
otherwise specified.
TYPICAL CHARACTERISTICS
Temperature Derating Graph
120
100
80
60
Safe Operating Area
40
20
0
120
40
71 85
Ambient Temperature (°C)
12.14.06
Technologies
MIN
0.3
0
-40
CENTRAL
MAX
OUTPUT SPECIFICATIONS
Item
Output Power (%)
FEATURES
TYP
Manufacturer of Passive and Discrete Semiconductor Components
800-684-5322 Inside US
949-453-1811 Outside US
Copyright © 2006 by CT Magnetics, DBA Central Technologies. All rights reserved.
CT Magnetics reserves the right to make improvements or change specifications without notice
DC/DC Converters
ctparts.com
CTDD3120DF-D1K-3 Series
Wide Input Isolated & Regulated
3W Output, Dual Output
OUTLINE DIMENSIONS & RECOMMENDED FOOTPRINT DETAILS
CTDD3120DF-D1K-3 Package
2
Bottom View
Side View
31.80
9.45
3
0.50
9 10 11
15.24
20.30
23 22
16 15 14
2.54
2 x 2.54
4.00
22.86
Note: All pins on a 2.54mm pitch; all pin diameters are 0.50mm; all dimensions in mm. (Tolerance:±0.25)
PIN CONNECTIONS
Bottom View
2
3
9 10 11
23 22
16 15 14
Pin
Function
2, 3
10, 15
14
11
9, 16
22, 23
-Vin
NC
+Vo
-Vo
0V
Vin
RECOMMENDED CIRCUIT
All the CTDD3120DF-D1K-3 Series have been tested according to the following recommended testing circuit before leaving
factory. This series should be tested under load. Never be tested under no load (See figure 1 & 2). If you want to further
decrease the input/output ripple, you can increase capacitance properly or choose capacitors with low ESR. However, the
capacitance should not be too high (See table 1). If you want to use the products in high EMI, please choose our metal
packaged products.
External Capacitor Table (table 1)
C in
5V
&
12V
100µF
24V
&
48V
10µF
C out
(0+70°C)
100µF
(electrolytic
capacitor)
Figure 2
C out
(-40+85°C)
47µF
(tantalum
capacitor)
lp
Figure 1
Vin
+Cin
DC
DC
Cout
+
Cout
+
Vout+
0V
Input Current (A)
Vin
Input Voltage
Range
Vo-
GND
Input Voltage (V)
CENTRAL
Technologies
12.14.06
Manufacturer of Passive and Discrete Semiconductor Components
800-684-5322 Inside US
949-453-1811 Outside US
Copyright © 2006 by CT Magnetics, DBA Central Technologies. All rights reserved.
CT Magnetics reserves the right to make improvements or change specifications without notice
Similar pages