AVAGO HFBR-2523 Versatile link the versatile fiber optic connection Datasheet

HFBR-0501 Series
Versatile Link
The Versatile Fiber Optic Connection
Data Sheet
Description
Features
The Versatile Link series is a complete family of fiber
optic link components for applications requiring a low
cost solution. The HFBR-0501 series includes
transmitters, receivers, connectors and cable specified
for easy design. This series of components is ideal for
solving problems with voltage isolation/insulation,
EMI/RFI immunity or data security. The optical link design
is simplified by the logic compatible receivers and
complete specifications for each component. The key
optical and electrical parameters of links configured with
the HFBR-0501 family are fully guaranteed from 0° to
70°C.
•
•
•
•
•
•
•
•
A wide variety of package configurations and connectors
provide the designer with numerous mechanical solutions
to meet application requirements. The transmitter and
receiver components have been designed for use in high
volume/low cost assembly processes such as auto
insertion and wave soldering.
Transmitters incorporate a 660 nm LED. Receivers
include a monolithic dc coupled, digital IC receiver with
open collector Schottky output transistor. An internal
pullup resistor is available for use in the HFBR-25X1/2/4
receivers. A shield has been integrated into the receiver
IC to provide additional, localized noise immunity.
Internal optics have been optimized for use with 1 mm
diameter plastic optical fiber. Versatile Link specifications
incorporate all connector interface losses. Therefore,
optical calculations for common link applications are
simplified.
Low cost fiber optic components
Enhanced digital links dc-5 MBd
Extended distance links up to 120 m at 40 kBd
Low current link: 6 mA peak supply current
Horizontal and vertical mounting
Interlocking feature
High noise immunity
Easy connectoring Simplex, Duplex, and Latching
connectors
• Flame retardant
• Transmitters incorporate a 660 nm Red LED for easy
visibility
• Compatible with standard TTL circuitry
Applications
•
•
•
•
•
•
•
•
•
Reduction of lightning/voltage transient susceptibility
Motor controller triggering
Data communications and local area networks
Electromagnetic Compatibility (EMC) for regulated
systems: FCC, VDE, CSA, etc.
Tempest-secure data processing equipment
Isolation in test and measurement instruments
Error free signalling for industrial and manufacturing
equipment
Automotive communications and control networks
Noise immune communication in audio and video
equipment
HFBR-0501 Series Part Number Guide
HFBR X5XX
1 = Transmitter
2 = Receiver
5 = 600 nm Transmitter and
Receiver Products
2 = Horizontal Package
3 = Vertical Package
1 = 5 MBd High Performance Link
2 = 1 MBd High Performance Link
3 = 40 kBd Low Current/Extended Distance Link
4 = 1 MBd Standard Link
6 = 155 MBd Receiver
7 = 155 MBd Transmitter
8 = 10 MBd High Performance Link
Link Selection Guide
(Links specified from 0 to 70°C, for plastic optical fiber unless specified.)
Signal Rate
Distance (m) 25°C
Distance (m)
40 kBd
120
110
1 MBd
20
10
1 MBd
55
45
5 Mbd
30
20
Transmitter
HFBR-1523
HFBR-1524
HFBR-1522
HFBR-1521
Receiver
HFBR-2523
HFBR-2524
HFBR-2522
HFBR-2521
Evaluation Kit
HFBR-0501 1 MBd Versatile Link:
This kit contains: HFBR-1524 Tx, HFBR-2524 Rx,
polishing kit, 3 styles of plastic connectors, Bulkhead
feedthrough, 5 meters of 1 mm diameter plastic cable,
lapping film and grit paper, and HFBR-0501 data sheet.
Application Literature
Application Note 1035 (Versatile Link)
Package and Handling Information
Package Orientation
The compact Versatile Link package is made of a flame
retardant VALOX® UL 94 V-0 material (UL file # E121562)
and uses the same pad layout as a standard, eight pin
dual-in-line package. Vertical and horizontal mountable
parts are available. These low profile Versatile Link
packages are stackable and are enclosed to provide a
dust resistant seal. Snap action simplex, simplex
latching, duplex, and duplex latching connectors are
offered with simplex or duplex cables.
Performance and pinouts for the vertical and horizontal
packages are identical. To provide additional attachment
support for the vertical Versatile Link housing, the
designer has the option of using a self-tapping screw
through a printed circuit board into a mounting hole at
the bottom of the package. For most applications this is
not necessary.
Package Housing Color
Versatile Link components and simplex connectors are
color coded to eliminate confusion when making
connections. Receivers are blue and transmitters are
gray, except for the HFBR-15X3 transmitter, which is
black.
VALOX® is a registered trademark of the General Electric Corporation.
2
Handling
Recommended Chemicals for Cleaning/Degreasing
Versatile Link components are auto-insertable. When
wave soldering is performed with Versatile Link
components, the optical port plug should be left in to
prevent contamination of the port. Do not use reflow
solder processes (i.e., infrared reflow or vapor-phase
reflow). Nonhalogenated water soluble fluxes
(i.e., 0% chloride), not rosin based fluxes, are recommended for use with Versatile Link components.
Alcohols: methyl, isopropyl, isobutyl. Aliphatics: hexane,
heptane, Other: soap solution, naphtha.
CAUTION
This bag contains
MOISTURE-SENSITIVE
DEVICES
Level
4
1. Shelf life in sealed bag: 12 months at < 40°C and < 90% Relative
Humidity (RH).
2. After this bag is opened, devices that will be subjected to wave
soldering, or equivalent processing (solder temperature < 260°C for
10 sec) must be:
a) Mounted within 72 hours at factory conditions of ≤ 30°C/60% RH.
b) Stored at ≤ 20% RH.
Versatile Link components are moisture sensitive
devices and are shipped in a moisture sealed bag. If the
components are exposed to air for an extended period
of time, they may require a baking step before the
soldering process. Refer to the special labeling on the
shipping tube for details.
3. Devices require baking, before mounting, if:
a) Desiccant changes to PINK.
b) If 2a or 2b are not met.
4. If baking is required, devices may be baked outside of tube for 20
hours at 75°C.
Bag Seal Date: ______________________________________________________
(If blank, see barcode label)
Note: LEVEL defined by EIA JEDEC Standard J-STD-020
Do not use partially halogenated hydrocarbons such as
1,1.1 trichloroethane, ketones such as MEK, acetone,
chloroform, ethyl acetate, methylene dichloride, phenol,
methylene chloride, or N-methylpyrolldone. Also, Avago
does not recommend the use of cleaners that use
halogenated hydrocarbons because of their potential
environmental harm.
Mechanical Dimensions
Horizontal Modules
2.0
(0.080)
Vertical Modules
6.8
(0.270)
10.2
(0.400)
5.1
(0.200)
18.8
(0.740)
0.64
(0.025)
7.62
(0.300)
3
4.2
(0.165)
7.71
7.6
(0.305)
(0.30)
3.81 (0.150) MAX.
3.56 (0.140) MIN.
0.51
(0.020)
0.64 (0.025) DIA.
2.8
(0.109)
7.6
(0.30)
1.85
(0.073)
1.27
(0.050)
2.5
(0.100)
18.8
0.740
Versatile Link Printed Board Layout Dimensions
Horizontal Module
Vertical Module
7.62
(0.300)
2.54
(0.100)
1.01 (0.040) DIA.
4
3
2
1
TOP VIEW
7.62
(0.300)
PCB EDGE
5
6
1.85 MIN.
(0.073)
DIMENSIONS IN MILLIMETERS (INCHES).
Interlocked (Stacked) Assemblies (refer to Figure 1)
Horizontal packages may be stacked by placing units
with pins facing upward. Initially engage the interlocking mechanism by sliding the L bracket body from
above into the L slot body of the lower package. Use a
straight edge, such as a ruler, to bring all stacked units
into uniform alignment. This technique prevents
potential harm that could occur to fingers and hands of
assemblers from the package pins. Stacked horizontal
packages can be disengaged if necessary. Repeated
stacking and unstacking causes no damage to individual
units.
To stack vertical packages, hold one unit in each hand,
with the pins facing away and the optical ports on the
bottom. Slide the L bracket unit into the L slot unit. The
straight edge used for horizontal package alignment is
not needed.
Stacking Horizontal Modules
Stacking Vertical Modules
Figure 1. Interlocked (stacked) horizontal or vertical packages
4
5 MBd Link (HFBR-15X1/25X1)
System Performance 0 to 70°C unless otherwise specified.
Parameter
Symbol Min. Typ. Max. Units
High
Data Rate
dc
5
MBd
Performance
Link Distance
19
m
5 MBd
(Standard Cable)
27
48
m
Link Distance
22
m
(Improved Cable)
27
53
m
Propagation
tPLH
80
140
ns
Delay
tPHL
50
140
ns
Pulse Width
Distortion tPLH-tPHL
tD
30
Conditions
BER ≤10-9, PRBS:27-1
IFdc = 60 mA
IFdc = 60 mA, 25°C
IFdc = 60 mA
IFdc = 60 mA, 25°C
RL = 560 Ω, CL = 30 pF
fiber length = 0.5 m
-21.6 ≤PR ≤-9.5 dBm
PR = -15 dBm
RL = 560 Ω, CL = 30 pF
ns
Ref.
Fig. 3
Note 3
Fig. 4
Note 3
Fig. 5, 8
Notes 1, 2
Fig. 5, 7
Notes:
1. The propagation delay for one metre of cable is typically 5 ns.
2. Typical propagation delay is measured at PR = -15 dBm.
3. Estimated typical link life expectancy at 40°C exceeds 10 years at 60 mA.
Figure 2. Typical 5 MBd interface circuit
100
I F – FORWARD CURRENT (mA)
I F – FORWARD CURRENT (mA)
100
50
40
OVERDRIVE
30
UNDERDRIVE
20
10
0°C–70°C
25°C
5
0
10
20
30
40
40
OVERDRIVE
30
UNDERDRIVE
20
10
0°C–70°C
25°C
5
50
– CABLE LENGTH – METRES
Figure 3. Guaranteed system performance with standard cable (HFBR-15X1/25X1)
5
50
0
10
20
30
40
50
60
– CABLE LENGTH – METRES
Figure 4. Guaranteed system performance with improved cable (HFBR-15X1/25X1)
Figure 5. 5 MBd propagation delay test circuit
Figure 6. Propagation delay test waveforms
500
70°C
400
HFBR-15X2/25X2
HFBR-15X4/25X4
tp – PROPAGATION DELAY – ns
tD – PULSE WIDTH DISTORTION – ns
500
25°C
0°C
300
200
100
0
-25
HFBR-15X1/25X1
-20
-15
-10
70°C
25°C
0°C
-5
0
PR – INPUT OPTICAL POWER – dBm
Figure 7. Typical link pulse width distortion vs. optical power
6
400
tpLH
HFBR-15X2/25X2
HFBR-15X4/25X4
300
200
HFBR-15X1/25X1
tpLH
100
tpHL
0
-25
-20
-15
-10
-5
0
PR – INPUT OPTICAL POWER – dBm
Figure 8. Typical link propagation delay vs. optical power
HFBR-15X1 Transmitter
8 DO NOT CONNECT
ANODE
CATHODE
Pin #
1
2
3
4
5
8
1
2
N.C.
3
N.C.
4
5 DO NOT CONNECT
Function
Anode
Cathode
Open
Open
Do not connect
Do not connect
Note: Pins 5 and 8 are for mounting and retaining
purposes only. Do not electrically connect these pins.
Absolute Maximum Ratings
Parameter
Storage Temperature
Operating Temperature
Lead Soldering Cycle
Symbol
TS
TA
Temp.
Time
Forward Input Current
Reverse Input Voltage
IFPK
IFdc
VBR
Min.
–40
–40
Max.
+85
+85
260
10
1000
80
5
Units
°C
°C
°C
sec
mA
Reference
Note 1
Note 2, 3
V
Notes:
1. 1.6 mm below seating plane.
2. Recommended operating range between 10 and 750 mA.
3. 1 µs pulse, 20 µs period.
All HFBR-15XX LED transmitters are classified as IEC 825-1 Accessible Emission Limit (AEL) Class 1
based upon the current proposed draft scheduled to go into effect on January 1, 1997. AEL Class 1 LED
devices are considered eye safe. Contact your local Avago sales representative for more information.
7
Transmitter Electrical/Optical Characteristics 0°C to 70°C unless otherwise specified.
Symbol
PT
Output Optical Power
Temperature Coefficient
Peak Emission
Wavelength
Forward Voltage
Forward Voltage
Temperature Coefficient
Effective Diameter
Numerical Aperture
Reverse Input Breakdown
Voltage
Diode Capacitance
Rise Time
Fall Time
∆PT /∆T
-0.85
Units
dBm
dBm
%/°C
λPK
660
nm
VF
∆VF /∆T
D
NA
VBR
CO
tr
tf
Min.
-16.5
-14.3
Typ.[5]
Parameter
Transmitter Output
Optical Power
1.45
5.0
Max.
-7.6
-8.0
1.67
-1.37
2.02
V
mV/°C
1
0.5
11.0
mm
86
80
40
pF
ns
ns
Conditions
IFdc = 60 mA
IFdc = 60 mA, 25°C
IFdc = 60 mA
Fig. 9
IFdc = 10 µA,
TA = 25°C
VF = 0, f = MHz
10% to 90%,
IF = 60 mA
V
Ref.
Notes 1, 2
Note 3
Notes:
1. Measured at the end of 0.5 m standard fiber optic cable with large area detector.
2. Optical power, P (dBm) = 10 Log [P(µW)/1000 µW].
3. Rise and fall times are measured with a voltage pulse driving the transmitter and a series connected 50 Ω load. A wide bandwidth optical to
electrical waveform analyzer, terminated to a 50 Ω input of a wide bandwidth oscilloscope, is used for this response time measurement.
5
PT – NORMALIZED OUTPUT POWER – dB
VF – FORWARD VOLTAGE – V
1.8
1.7
0°C
1.6
25°C
70°C
1.5
-5
-10
-15
-20
1.4
2
10
100
IFdc – TRANSMITTER DRIVE CURRENT (mA)
Figure 9. Typical forward voltage vs. drive current
8
0
2
10
100
IFdc – TRANSMITTER DRIVE CURRENT (mA)
Figure 10. Normalized typical output power vs. drive current
HFBR-25X1 Receiver
DO NOT CONNECT
5
1000 Ω
4
RL
3
VCC
2
1
DO NOT CONNECT
Pin #
1
2
3
4
5
8
GROUND
VO
8
Function
VO
Ground
VCC
RL
Do not connect
Do not connect
Note: Pins 5 and 8 are for mounting and retaining
purposes only. Do not electrically connect these pins.
Absolute Maximum Ratings
Parameter
Storage Temperature
Operating Temperature
Lead Soldering Cycle
Symbol
TS
TA
Min.
–40
–40
Temp.
Time
Supply Voltage
Output Collector Current
Output Collector Power Dissipation
Output Voltage
Pull-up Voltage
Fan Out (TTL)
VCC
IOAV
POD
VO
VP
N
–0.5
–0.5
–5
Max.
+85
+85
260
10
7
25
40
18
VCC
5
Units
°C
°C
°C
sec
V
mA
mW
V
V
Reference
Note 1
Note 2
Notes:
1. 1.6 mm below seating plane.
2. It is essential that a bypass capacitor 0.01 µF be connected from pin 2 to pin 3 of the receiver. Total lead length between both ends of the capacitor
and the pins should not exceed 20 mm.
Receiver Electrical/Optical Characteristics
0°C to 70°C, 4.75 V ≤VCC ≤5.25 V unless otherwise specified
Parameter
Input Optical Power
Level for Logic “0”
Symbol
PR(L)
Min.
–21.6
Typ.
–21.6
Input Optical Power
Level for Logic “1”
High Level Output Current
Low Level Output Current
PR(H)
IOH
VOL
High Level Supply
Current
Low Level Supply Current
Effective Diameter
Numerical Aperture
Internal Pull-up Resistor
Max.
–9.5
Units
dBm
–8.7
–43
dBm
5
0.4
250
0.5
µA
V
ICCH
3.5
6.3
mA
ICCL
6.2
10
mA
D
NA
RL
1
0.5
1000
680
Conditions
VOL = 0.5 V
IOL = 8 mA
VOL = 0.5 V
IOL = 8 mA, 25°C
VOL = 5.25 V
IOH ≤250 µA
VO = 18 V, PR = 0
IOL = 8 mA,
PR = PR(L)MIN
VCC = 5.25 V,
PR = 0
VCC = 5.25 V
PR = -12.5 dBm
Ref.
Notes 1,
2, 4
Note 1
Note 3
Note 3
Note 3
Note 3
mm
1700
Ω
Notes:
1. Optical flux, P (dBm) = 10 Log [P (µW)/1000 µW].
2. Measured at the end of the fiber optic cable with large area detector.
3. RL is open.
4. Pulsed LED operation at IF > 80 mA will cause increased link tPLH propagation delay time. This extended tPLH time contributes to increased pulse
width distortion of the receiver output signal.
9
1 MBd Link
(High Performance HFBR-15X2/25X2, Standard HFBR-15X4/25X4)
System Performance Under recommended operating conditions unless otherwise specified.
High
Performance
1 MBd
Parameter
Data Rate
Link Distance
(Standard Cable)
Symbol
Link Distance
(Improved Cable)
Propagation
Delay
Pulse Width
Distortion tPLH-tPHL
Standard
1 MBd
Parameter
Data Rate
Link Distance
(Standard Cable)
45
56
Pulse Width
Distortion tPLH-tPHL
Typ. Max. Units
1
MBd
m
70
m
78
tPLH
tPHL
180
100
tD
80
Symbol
Link Distance
(Improved Cable)
Propagation
Delay
Min.
dc
39
47
Min.
dc
8
17
10
19
250
140
m
m
IFdc = 60 mA
IFdc = 60 mA, 25°C
ns
ns
RL = 560 Ω, CL = 30 pF
I = 0.5 metre
PR = -24 dBm
PR = -24 dBm
RL = 560 Ω, CL = 30 pF
ns
Typ. Max. Units
1
MBd
m
43
m
48
tPLH
tPHL
180
100
tD
80
250
140
Conditions
BER ≤10-9, PRBS:27-1
IFdc = 60 mA
IFdc = 60 mA, 25°C
Conditions
BER ≤10-9, PRBS:27-1
IFdc = 60 mA
IFdc = 60 mA, 25°C
m
m
IFdc = 60 mA
IFdc = 60 mA, 25°C
ns
ns
RL = 560 Ω, CL = 30 pF
I = 0.5 metre
PR = -20 dBm
PR = -20 dBm
RL = 560 Ω, CL = 30 pF
ns
Ref.
Fig. 14
Notes 1,
3, 4
Fig. 15
Notes 1,
3, 4
Fig. 16, 18
Notes 2, 4
Fig. 16, 17
Note 4
Ref.
Fig. 12
Notes 1,
3, 4
Fig. 13
Notes 1,
3, 4
Fig. 16, 18
Notes 2, 4
Fig. 16, 17
Note 4
Notes:
1. For IFPK > 80 mA, the duty factor must be such as to keep IFdc ≤80 mA. In addition, for IFPK > 80 mA, the following rules for pulse width apply:
IFPK ≤160 mA: Pulse width ≤1 ms
IFPK > 160 mA: Pulse width ≤1 µS, period ≥20 µS.
2. The propagation delay for one meter of cable is typically 5 ns.
3. Estimated typical link life expectancy at 40°C exceeds 10 years at 60 mA.
4. Pulsed LED operation at IFPK > 80 mA will cause increased link tPLH propagation delay time. This extended tPLH time contributes to increased pulse
width distortion of the receiver output signal.
10
Figure 11. Required 1 MBd interface circuit
The HFBR-25X2 receiver can not be overdriven when using the required
interface circuit shown in Figure 11.
80
80
I F – FORWARD CURRENT (mA)
100
90
I F – FORWARD CURRENT (mA)
100
90
70
60
50
40
HFBR-15X4/25X4
30
0°C–70°C
25°C
20
0
5
10
15
20
70
60
50
40
HFBR-15X4/25X4
30
0°C–70°C
25°C
20
25
0
10
– CABLE LENGTH – METRES
Figure 12. Guaranteed system performance for the HFBR-15X4/25X4 Link with
standard cable
100
IF – FORWARD CURRENT (mA)
IF – FORWARD CURRENT (mA)
30
Figure 13. Guaranteed system performance for the HFBR-15X4/25X4 Link with
improved cable
100
50
40
30
20
UNDERDRIVE
10
50
40
30
20
UNDERDRIVE
10
0°C–70°C
25°C
5
0°C–70°C
25°C
5
0
10
20
30
40
50
– CABLE LENGTH – METRES
Figure 14. Guaranteed system performance for the HFBR-15X2/25X2 Link with
standard cable
11
20
– CABLE LENGTH – METRES
0
10
20
30
40
50
60
– CABLE LENGTH – METRES
Figure 15. Guaranteed system performance for the HFBR-15X2/25X2 Link with
improved cable
Figure 16. 1 MBd propagation delay test circuit
500
70°C
400
HFBR-15X2/25X2
HFBR-15X4/25X4
tp – PROPAGATION DELAY – ns
tD – PULSE WIDTH DISTORTION – ns
500
25°C
0°C
300
200
100
0
-25
HFBR-15X1/25X1
-20
-15
-10
70°C
25°C
0°C
-5
0
PR – INPUT OPTICAL POWER – dBm
Figure 17. Pulse width distortion vs. optical power
Figure 19. Propagation delay test waveforms
12
400
tpLH
HFBR-15X2/25X2
HFBR-15X4/25X4
300
200
HFBR-15X1/25X1
tpLH
100
tpHL
0
-25
-20
-15
-10
-5
0
PR – INPUT OPTICAL POWER – dBm
Figure 18. Typical link propagation delay vs. optical power
HFBR-15X2/15X4 Transmitters
Pin #
1
2
3
4
5
8
8 DO NOT CONNECT
ANODE
CATHODE
1
2
N.C.
3
N.C.
4
5 DO NOT CONNECT
Function
Anode
Cathode
Open
Open
Do not connect
Do not connect
Note: Pins 5 and 8 are for mounting and retaining
purposes only. Do not electrically connect these pins.
Absolute Maximum Ratings
Parameter
Storage Temperature
Operating Temperature
Lead Soldering Cycle
Symbol
TS
TA
Min.
–40
–40
Temp.
Time
Forward Input Current
Reverse Input Voltage
IFPK
IFdc
VBR
Max.
+85
+85
260
10
1000
80
5
Units
°C
°C
°C
sec
mA
Reference
Note 1
Note 2, 3
V
Notes:
1. 1.6 mm below seating plane.
2. Recommended operating range between 10 and 750 mA.
3. 1 µs pulse, 20 µs period.
All HFBR-15XX LED transmitters are classified as IEC 825-1 Accessible Emission Limit (AEL) Class 1
based upon the current proposed draft scheduled to go into effect on January 1, 1997. AEL Class 1 LED
devices are considered eye safe. Contact your Avago sales representative for more information.
Transmitter Electrical/Optical Characteristics 0°C to 70°C unless otherwise specified.
For forward voltage and output power vs. drive current graphs.
Parameter
Symbol
Min.
Typ.
Transmitter HFBR-15X2
PT
–13.6
Output
–11.2
Optical
HFBR-15X4
PT
–17.8
Power
–15.5
Output Optical Power
∆PT /∆T
–0.85
Temperature Coefficient
Peak Emission Wavelength
λPK
660
Forward Voltage
VF
1.45
1.67
Forward Voltage
∆VF /∆T
–1.37
Temperature Coefficient
Effective Diameter
DT
1
Numerical Aperture
NA
0.5
Reverse Input Breakdown
VBR
5.0
11.0
Voltage
Diode Capacitance
CO
86
Rise Time
tr
80
Fall Time
tf
40
Max.
–4.5
–5.1
–4.5
–5.1
Units
dBm
dBm
Conditions
IFdc = 60 mA
IFdc = 60 mA, 25°C
IFdc = 60 mA
IFdc = 60 mA, 25°C
Ref.
%/°C
2.02
nm
V
mV/°C
IFdc = 60 mA
Fig. 11
mm
V
pF
ns
ns
IFdc = 10 µA,
TA = 25°C
VF = 0, f = 1 MHz
10% to 90%,
IF = 60 mA
Note 1
Note:
1. Rise and fall times are measured with a voltage pulse driving the transmitter and a series connected 50 Ω load. A wide bandwidth optical to
electrical waveform analyzer, terminated to a 50 Ω input of a wide bandwidth oscilloscope, is used for this response time measurement.
13
HFBR-25X2/25X4 Receivers
DO NOT CONNECT
5
1000 Ω
4
RL
3
VCC
GROUND
2
VO
1
DO NOT CONNECT
Pin #
1
2
3
4
5
8
8
Function
VO
Ground
VCC
RL
Do not connect
Do not connect
Note: Pins 5 and 8 are for mounting and retaining
purposes only. Do not electrically connect these pins.
Absolute Maximum Ratings
Parameter
Storage Temperature
Operating Temperature
Lead Soldering Cycle
Symbol
TS
TA
Min.
–40
–40
Max.
+85
+85
260
10
7
25
40
18
VCC
5
Temp.
Time
Supply Voltage
Output Collector Current
Output Collector Power Dissipation
Output Voltage
Pull-up Voltage
Fan Out (TTL)
VCC
IOAV
POD
VO
VP
N
–0.5
–0.5
–5
Units
°C
°C
°C
sec
V
mA
mW
V
V
Reference
Note 1
Note 2
Notes:
1. 1.6 mm below seating plane.
2. It is essential that a bypass capacitor 0.01 µF be connected from pin 2 to pin 3 of the receiver. Total lead length between both ends of the capacitor
and the pins should not exceed 20 mm.
Receiver Electrical/Optical Characteristics 0°C to 70°C, 4.75 V ≤VCC ≤5.25 V unless otherwise specified.
Parameter
Receiver
Optical Input
Power Level
Logic 0
HFBR-2522
Symbol
PR(L)
HFBR-2524
Min.
–24
Typ.
Max.
Units
dBm
Conditions
VOL = 0 V
IOL = 8 mA
–20
Optical Input Power
Level Logic 1
High Level Output Current
Low Level Output Voltage
PR(H)
IOH
VOL
High Level Supply Current
Note 4
-43
dBm
5
0.4
250
0.5
µA
V
ICCH
3.5
6.3
mA
Low Level Supply Current
ICCL
6.2
10
mA
Effective Diameter
Numerical Aperture
Internal Pull-up Resistor
D
NA
RL
1
0.5
1000
680
Ref.
Notes 1, 2, 3
VOH = 5.25 V
IOH = ≤250 µA
VO = 18 V, PR = 0
IOL = 8 mA
PR = PR(L)MIN
VCC = 5.25 V,
PR = 0
VCC = 5.25 V,
PR = -12.5 dBm
Note 5
Note 5
Note 5
Note 5
mm
1700
Ω
Notes:
1. Measured at the end of the fiber optic cable with large area detector.
2. Pulsed LED operation at IF > 80 mA will cause increased link tPLH propagation delay time. This extended tPLH time contributes to increased pulse
width distortion of the receiver output signal.
3. The LED drive circuit of Figure 11 is required for 1 MBd operation of the HFBR-25X2/25X4.
4. Optical flux, P (dBm) = 10 Log [P(µW)/1000 µW].
5. RL is open.
14
40 kBd Link
System Performance Under recommended operating conditions unless otherwise specified.
Parameter
Data Rate
Link Distance
(Standard Cable)
Link Distance
(Improved Cable)
Propagation
Delay
Pulse Width
Distortion tPLH-tPHL
Symbol
Min.
dc
13
94
15
111
tPLH
tPHL
tD
Typ.
Max.
40
Units
kBd
m
m
m
m
µs
µs
µs
41
138
45
154
4
2.5
7
Conditions
BER ≤10-9, PRBS: 27 - 1
IFdc = 2 mA
IFdc = 60 mA
IFdc = 2 mA
IFdc = 60 mA
RL = 3.3 kΩ, CL = 30 pF
PR = -25 dBm, 1 m fiber
-39 ≤PR≤- 14 dBm
RL = 3.3 kΩ, CL = 30 pF
Ref.
Fig. 21
Note 1
Fig. 22
Note 1
Fig. 22, 25
Note 2
Fig. 23, 24
Notes:
1. Estimated typical link life expectancy at 40°C exceeds 10 years at 60 mA.
2. The propagation delay for one metre of cable is typically 5 ns.
Figure 20. Typical 40 kBd interface circuit
120
100
80
60
40
20
10
6
4
HFBR-15X3/25X3
2
1
0°C–70°C
25°C
0
10
20 30
40 50
60
70 80 90 100
– CABLE LENGTH – METRES
Figure 21. Guaranteed system performance with standard cable
15
I F – FORWARD CURRENT (mA)
I F – FORWARD CURRENT (mA)
120
100
80
60
40
20
10
6
HFBR-15X3/25X3
4
2
0°C–70°C
25°C
0 10 20 30 40 50 60 70 80 90 100 110
– CABLE LENGTH – METRES
Figure 22. Guaranteed system performance with improved cable
Figure 23. 40 kBd propagation delay test circuit
8
7
5
t P – PROPAGATION DELAY – µs
t D – PULSE WIDTH DISTORTION – µs
6
4
3
2
1
0
-40
-34
-28
-22
-16
-10
P R – INPUT OPTICAL POWER, dBm
Figure 24. Typical link pulse width distortion vs. optical power
Figure 26. Propagation delay test waveforms
16
6
t PLH
5
4
3
2
t PHL
1
0
-40
-34
-28
-22
-16
-10
PR – INPUT OPTICAL POWER, dBm
Figure 25. Typical link propagation delay vs. optical power
HFBR-15X3 Transmitter
Pin #
1
2
3
4
5
8
8 DO NOT CONNECT
ANODE
CATHODE
1
2
N.C.
3
N.C.
4
5 DO NOT CONNECT
Function
Anode
Cathode
Open
Open
Do not connect
Do not connect
Note: Pins 5 and 8 are for mounting and retaining
purposes only. Do not electrically connect these pins.
Absolute Maximum Ratings
Parameter
Storage Temperature
Operating Temperature
Lead Soldering Cycle
Symbol
TS
TA
Min.
–40
–40
Temp.
Time
Forward Input Current
Reverse Input Voltage
IFPK
IFdc
VBR
Max.
+85
+85
260
10
1000
80
5
Units
°C
°C
°C
sec
mA
Reference
Note 1
Note 2, 3
V
Notes:
1. 1.6 mm below seating plane.
2. Recommended operating range between 10 and 750 mA.
3. 1 µs pulse, 20 µs period.
All HFBR-15XX LED transmitters are classified as IEC 825-1 Accessible Emission Limit (AEL) Class 1
based upon the current proposed draft scheduled to go into effect on January 1, 1997. AEL Class 1 LED
devices are considered eye safe. Contact your Avago sales representative for more information.
Transmitter Electrical/Optical Characteristics 0°C to 70°C unless otherwise specified.
For forward voltage and output power vs. drive current graphs.
Parameter
Symbol
Min.
Typ.
Transmitter Output
PT
–11.2
Optical Power
–13.6
–35.5
Output Optical Power
∆PT /∆T
–0.85
Temperature Coefficient
Peak Emission
λPK
660
Wavelength
Forward Voltage
VF
1.45
1.67
Forward Voltage
∆VF /∆T
–1.37
Temperature Coefficient
Effective Diameter
D
1
Numerical Aperture
NA
0.5
Reverse Input Breakdown
VBR
5.0
11.0
Voltage
Diode Capacitance
CO
86
Rise Time
tr
80
Fall Time
tf
40
Max.
–5.1
–4.5
Units
dBm
Conditions
IFdc = 60 mA, 25°C
IFdc = 60 mA
IFdc = 2 mA, 0-70°C
Ref.
Notes 3, 4
Fig. 9, 10
%/°C
nm
2.02
V
mV/°C
IFdc = 60 mA
Fig. 18
mm
V
pF
ns
IFdc = 10 µA,
TA = 25°C
VF = 0, f = 1 MHz
10% to 90%,
IF = 60 mA
Note 1
Note:
1. Rise and fall times are measured with a voltage pulse driving the transmitter and a series connected 50 Ω load. A wide bandwidth optical to
electrical waveform analyzer, terminated to a 50 Ω input of a wide bandwidth oscilloscope, is used for this response time measurement.
17
HFBR-25X3 Receiver
DO NOT CONNECT
5
4
VCC
3
OPEN
2
1
DO NOT CONNECT
Pin #
1
2
3
4
5
8
GROUND
VO
8
Function
VO
Ground
Open
VCC
Do not connect
Do not connect
Note: Pins 5 and 8 are for mounting and retaining
purposes only. Do not electrically connect these pins.
Absolute Maximum Ratings
Parameter
Storage Temperature
Operating Temperature
Lead Soldering Cycle
Symbol
TS
TA
Min.
–40
–40
Max.
+85
+85
260
10
7
5
25
7
Temp.
Time
Supply Voltage
Average Output Collector Current
Output Collector Power Dissipation
Output Voltage
VCC
IO
POD
VO
–0.5
–1
–0.5
Units
°C
°C
°C
sec
V
mA
mW
V
Reference
Note 1
Note 2
Notes:
1. 1.6 mm below seating plane.
2. It is essential that a bypass capacitor 0.01 µF be connected from pin 2 to pin 3 of the receiver.
Receiver Electrical/Optical Characteristics 0°C to 70°C, 4.5 V ≤VCC ≤5.5 V unless otherwise specified.
Parameter
Input Optical Power
Level Logic 0
Symbol
PR(L)
Min.
–39
–39
Typ.
Input Optical Power
Level Logic 1
High Level Output Voltage
Low Level Output Voltage
PR(H)
High Level Supply Current
Low Level Supply Current
ICCH
ICCL
1.2
2.9
Effective Diameter
Numerical Aperture
D
NA
1
0.5
VOH
VOL
Max.
–13.7
–13.3
Units
dBm
–53
dBm
0.4
V
V
1.9
3.7
mA
mA
2.4
Conditions
VO = VOL, IOL = 3.2 mA
VO = VOL,
IOH = 8 mA, 25°C
VOH = 5.5 V
IOH = ≤40 µA
IO = -40 µA, PR = 0 µW
IOL = 3.2 mA
PR = PR(L)MIN
VCC = 5.5 V, PR = 0 µW
VCC = 5.5 V,
PR = PRL (MIN)
Ref.
Notes 1,
2, 3
Note 3
Note 4
Note 4
mm
Notes:
1. Measured at the end of the fiber optic cable with large area detector.
2. Optical flux, P (dBm) = 10 Log P(µW)/1000 µW.
3. Because of the very high sensitivity of the HFBR-25X3, the digital output may switch in response to ambient light levels when a cable is not
occupying the receiver optical port. The designer should take care to filter out signals from this source if they pose a hazard to the system.
4. Including current in 3.3 k pull-up resistor.
18
For product information and a complete list of distributors, please go to our website:
www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries.
Data subject to change. Copyright © 2008 Avago Technologies Limited. All rights reserved. Obsoletes 5968-1712E
5988-1765EN January 30, 2008
Similar pages