INTERSIL ISL12022IBZ

ISL12022
®
Real Time Clock with On Chip ±5ppm Temp Compensation
Data Sheet
June 23, 2009
Low Power RTC with Battery-Backed SRAM
and Embedded Temp Compensation ±5ppm
with Auto Daylight Saving
The ISL12022 device is a low power real time clock with an
embedded Temp sensor for oscillator compensation,
clock/calendar, power fail, low battery monitor, brownout
indicator, single periodic or polled alarms, intelligent
battery-backup switching, Battery Reseal™ function and 128
bytes of battery-backed user SRAM.
The oscillator uses an external, low-cost 32.768kHz crystal.
The real time clock tracks time with separate registers for
hours, minutes, and seconds. The device has calendar
registers for date, month, year and day of the week. The
calendar is accurate through 2099, with automatic leap year
correction.
Daylight Savings time adjustment is done automatically,
using parameters entered by the user. Power fail and battery
monitors offer user-selectable trip levels. A time stamp
function records the time and date of switchover from VDD to
VBAT power, and also from VBAT to VDD power.
Pinout
FN6659.2
Features
• Real Time Clock/Calendar
- Tracks Time in Hours, Minutes and Seconds
- Day of the Week, Day, Month and Year
• On-chip Oscillator Compensation Over the Operating
Temp Range
- ±5ppm Over -40°C to +85°C
• 10-bit Digital Temperature Sensor Output
- ±2°C Accuracy
• Customer Programmable Day Light Saving Time
• 15 Selectable Frequency Outputs
• 1 Alarm
- Settable to the Second, Minute, Hour, Day of the Week,
Day, or Month
- Single Event or Pulse Interrupt Mode
• Battery Reseal™ Function to Extend Battery Shelf Life
• Automatic Backup to Battery or Super Capacitor
- Operation to VBAT = 1.8V
- 1.0µA Battery Supply Current
• Battery Status Monitor
- 2 User Programmable Levels
- Seven Selectable Voltages for Each Level
ISL12022
(8 LD SOIC)
TOP VIEW
X1
1
8
VDD
X2
2
7
IRQ/FOUT
VBAT
3
6
SCL
GND
4
5
SDA
• Power Status Brownout Monitor
- Six Selectable Trip Levels, from 2.295V to 4.675V
• Oscillator Failure Detection
• Time Stamp for First VDD to VBAT, and Last VBAT to VDD
• 128 Bytes Battery-Backed User SRAM
• I2C Bus™
- 400kHz Clock Frequency
• 8 Ld SOIC Package
• Pb-Free (RoHS Compliant)
Applications
• Utility Meters
• POS Equipment
• Medical Devices
• Security Systems
• Vending Machines
• White Goods
• Printers and Copiers
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
I2C Bus™ is a trademark owned by NXP Semiconductors Netherlands, B.V.
Copyright Intersil Americas Inc. 2008, 2009. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
ISL12022
Ordering Information
PART NUMBER
(Note)
PART
MARKING
ISL12022IBZ*
12022 IBZ
VDD RANGE
(V)
TEMP RANGE
(°C)
2.7 to 5.5
-40 to +85
PACKAGE
(Pb-free)
8 Ld SOIC
PKG.
DWG. #
M8.15
*Add “-T” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100%
matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations).
Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J
STD-020.
Block Diagram
SDA
BUFFER
SDA
I2C
INTERFACE
SCL
BUFFER
SCL
SECONDS
CONTROL
LOGIC
REGISTERS
MINUTES
HOURS
DAY OF WEEK
X1
CRYSTAL
OSCILLATOR
X2
RTC
DIVIDER
DATE
MONTH
VDD
POR
FREQUENCY
OUT
YEAR
ALARM
VTRIP
CONTROL
REGISTERS
USER
SRAM
SWITCH
INTERNAL
SUPPLY
VBAT
GND
TEMPERATURE
SENSOR
IRQ/FOUT
FREQUENCY
CONTROL
Pin Descriptions
PIN
NUMBER
SYMBOL
1
X1
Crystal Input. The X1 pin is the input of an inverting amplifier and is intended to be connected to one pin of an
external 32.768kHz quartz crystal. X1 can also be driven directly from a 32.768kHz source.
2
X2
Crystal Output. The X2 pin is the output of an inverting amplifier and is intended to be connected to one pin of an
external 32.768kHz quartz crystal. X2 should be left open when X1 is driven from external source.
3
VBAT
Backup Supply. This input provides a backup supply voltage to the device. VBAT supplies power to the device in the
event that the VDD supply fails. This pin should be tied to ground if not used.
4
GND
Ground.
5
SDA
Serial Data. SDA is a bi-directional pin used to transfer serial data into and out of the device. It has an open drain
output and may be wire OR’ed with other open drain or open collector outputs.
6
SCL
Serial Clock. The SCL input is used to clock all serial data into and out of the device.
7
IRQ/FOUT
8
VDD
DESCRIPTION
Interrupt Output/Frequency Output. Multi-functional pin that can be used as interrupt or frequency output pin. The
function is set via the configuration register. It is an open-drain output.
Power Supply.
2
FN6659.2
June 23, 2009
ISL12022
Absolute Maximum Ratings
Thermal Information
Voltage on VDD, VBAT and IRQ/FOUT pins
(respect to ground) . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6.0V
Voltage on SCL and SDA pins
(respect to ground) . . . . . . . . . . . . . . . . . . . . . -0.3V to VDD + 0.3V
Voltage on X1 and X2 pins
(respect to ground) . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 2.5V
ESD Rating
Human Body Model (Per MIL-STD-883 Method 3014) . . . . .>3kV
Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>300V
Thermal Resistance (Typical, Note 1)
θJA (°C/W)
8 Ld SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
110
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Pb-free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTE:
1. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
DC Operating Characteristics - RTC Test Conditions: VDD = +2.7 to +5.5V, TA = -40°C to +85°C, unless otherwise stated.
SYMBOL
PARAMETER
CONDITIONS
MIN
(Note 9)
TYP
(Note 5)
MAX
(Note 9)
UNITS
NOTES
VDD
Main Power Supply
(Note 11)
2.7
5.5
V
VBAT
Battery Supply Voltage
(Note 11)
1.8
5.5
V
2
IDD1
Supply Current. (I2C not Active,
VDD = 5V
4.1
7
µA
3, 4
Temperature Conversion not Active,
FOUT not Active)
VDD = 3V
3.5
6
µA
3, 4
IDD2
Supply Current. (I2C Active,
Temperature Conversion not Active,
FOUT not Active)
VDD = 5V
200
500
µA
3, 4
IDD3
Supply Current. (I2C not Active,
Temperature Conversion Active,
FOUT not Active)
VDD = 5V
120
400
µA
3, 4
IBAT
Battery Supply Current
VDD = 0V, VBAT = 3V, TA = +25°C
1.0
1.6
µA
3
VDD = 0V, VBAT = 3V
1.0
5.0
µA
3
100
nA
IBATLKG
Battery Input Leakage
VDD = 5.5V, VBAT = 1.8V
ILI
Input Leakage Current on SCL
VIL = 0V, VIH = 5.5V
-1.0
±0.1
1.0
µA
ILO
I/O Leakage Current on SDA
VIL = 0V, VIH = 5.5V
-1.0
±0.1
1.0
µA
VBATM
Battery Level Monitor Threshold
-100
+100
mV
VPBM
Brownout Level Monitor Threshold
-100
+100
mV
VTRIP
VBAT Mode Threshold
2.4
V
(Note 11)
2.0
2.2
VTRIPHYS
VTRIP Hysteresis
30
mV
7
VBATHYS
VBAT Hysteresis
50
mV
7
ΔFoutT
Oscillator Stability vs Temperature
VDD = 3.3V
-5
+5
ppm
10
ΔFoutV
Oscillator Stability vs Voltage
2.7V ≤ VDD ≤ 5.5V
-3
+3
ppm
10
ΔATLSB
AT Sensitivity per LSB
BETA (4:0) = 10000
0.5
2
ppm
10
Temperature Sensor Accuracy
VDD = VBAT = 3.3V
°C
7
Temp
1
±2
IRQ/FOUT (OPEN DRAIN OUTPUT)
VOL
Output Low Voltage
3
VDD = 5.5V, IOL = 3mA
0.4
V
VDD = 2.7V, IOL = 1mA
0.4
V
FN6659.2
June 23, 2009
ISL12022
Power-Down Timing
SYMBOL
VDD SR-
Test Conditions: VDD = +2.7 to +5.5V, TA = -40°C to +85°C, unless otherwise stated.
PARAMETER
CONDITIONS
MIN
(Note 9)
TYP
(Note 5)
VDD Negative Slew rate
MAX
(Note 9)
UNITS
NOTES
10
V/ms
6
I2C Interface Specifications Test Conditions: VDD = +2.7 to +5.5V, TA = -40°C to +85°C, unless otherwise specified.
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
(Note 9)
TYP
(Note 5)
MAX
(Note 9)
UNITS
VIL
SDA and SCL Input Buffer LOW
Voltage
-0.3
0.3 x VDD
V
VIH
SDA and SCL Input Buffer HIGH
Voltage
0.7 x VDD
VDD + 0.3
V
SDA and SCL Input Buffer
Hysteresis
0.05 x VDD
Hysteresis
VOL
SDA Output Buffer LOW Voltage,
Sinking 3mA
VDD = 5V, IOL = 3mA
CPIN
SDA and SCL Pin Capacitance
TA = +25°C, f = 1MHz,
VDD = 5V, VIN = 0V,
VOUT = 0V
fSCL
SCL Frequency
0
V
0.02
0.4
V
10
pF
400
kHz
tIN
Pulse Width Suppression Time at
SDA and SCL Inputs
Any pulse narrower than the
max spec is suppressed.
50
ns
tAA
SCL Falling Edge To SDA Output
Data Valid
SCL falling edge crossing
30% of VDD, until SDA exits
the 30% to 70% of VDD
window.
900
ns
tBUF
Time the Bus Must be Free Before SDA crossing 70% of VDD
the Start of a New Transmission
during a STOP condition, to
SDA crossing 70% of VDD
during the following START
condition.
1300
ns
tLOW
Clock LOW Time
Measured at the 30% of VDD
crossing.
1300
ns
tHIGH
Clock HIGH Time
Measured at the 70% of VDD
crossing.
600
ns
tSU:STA
START Condition Setup Time
SCL rising edge to SDA
falling edge. Both crossing
70% of VDD.
600
ns
tHD:STA
START Condition Hold Time
From SDA falling edge
crossing 30% of VDD to SCL
falling edge crossing 70% of
VDD.
600
ns
tSU:DAT
Input Data Setup Time
From SDA exiting the 30% to
70% of VDD window, to SCL
rising edge crossing 30% of
VDD.
100
ns
tHD:DAT
Input Data Hold Time
From SCL falling edge
crossing 30% of VDD to SDA
entering the 30% to 70% of
VDD window.
0
tSU:STO
STOP Condition Setup Time
From SCL rising edge
crossing 70% of VDD, to SDA
rising edge crossing 30% of
VDD.
600
4
900
NOTES
7, 8
7, 8
ns
ns
FN6659.2
June 23, 2009
ISL12022
I2C Interface Specifications Test Conditions: VDD = +2.7 to +5.5V, TA = -40°C to +85°C, unless otherwise specified. (Continued)
SYMBOL
tHD:STO
PARAMETER
MIN
(Note 9)
TEST CONDITIONS
TYP
(Note 5)
MAX
(Note 9)
UNITS
600
ns
0
ns
NOTES
STOP Condition Hold Time
From SDA rising edge to
SCL falling edge. Both
crossing 70% of VDD.
Output Data Hold Time
From SCL falling edge
crossing 30% of VDD, until
SDA enters the 30% to 70%
of VDD window.
tR
SDA and SCL Rise Time
From 30% to 70% of VDD.
20 + 0.1 x Cb
300
ns
8
tF
SDA and SCL Fall Time
From 70% to 30% of VDD.
20 + 0.1 x Cb
300
ns
8
Cb
Capacitive loading of SDA or SCL
Total on-chip and off-chip
10
400
pF
8
kΩ
8
tDH
RPU
SDA and SCL Bus Pull-up Resistor Maximum is determined by
Off-chip
tR and tF.
For Cb = 400pF, max is about
2kΩ~2.5kΩ.
For Cb = 40pF, max is about
15kΩ~20kΩ
1
NOTES:
2. Temperature Conversion is inactive below VBAT = 2.7V. Device operation is not guaranteed at VBAT<1.8V.
3. IRQ/FOUT inactive.
4. VDD > VBAT +VBATHYS
5. Specified at +25°C.
6. In order to ensure proper timekeeping, the VDD SR- specification must be followed.
7. Limits should be considered typical and are not production tested.
8. These are I2C specific parameters and are not tested, however, they are used to set conditions for testing devices to validate
specification.
9. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by
characterization and are not production tested.
10. Specifications are typical and require using a recommended crystal (see “Application Section” on page 25).
11. Minimum VDD and/or VBAT of 1V to sustain the SRAM. The value is based on characterization and it is not tested.
5
FN6659.2
June 23, 2009
ISL12022
SDA vs SCL Timing
tHIGH
tF
SCL
tLOW
tR
tSU:DAT
tSU:STA
tHD:DAT
tSU:STO
tHD:STA
SDA
(INPUT TIMING)
tAA
tDH
tBUF
SDA
(OUTPUT TIMING)
Symbol Table
WAVEFORM
INPUTS
OUTPUTS
Must be steady
Will be steady
May change
from LOW
to HIGH
Will change
from LOW
to HIGH
May change
from HIGH
to LOW
Will change
from HIGH
to LOW
Don’t Care:
Changes Allowed
Changing:
State Not Known
N/A
Center Line is
High Impedance
EQUIVALENT AC OUTPUT LOAD CIRCUIT FOR VDD = 5V
5.0V
1533Ω
FOR VOL= 0.4V
AND IOL = 3mA
SDA
AND
IRQ/FOUT
100pF
FIGURE 1. STANDARD OUTPUT LOAD FOR TESTING THE
DEVICE WITH VDD = 5.0V
6
FN6659.2
June 23, 2009
ISL12022
1050
1600
1000
1400
950
1200
IBAT (nA)
VBAT CURRENT (nA)
Typical Performance Curves Temperature is +25°C unless otherwise specified.
900
VBAT = 5.5V
1000
VBAT = 3.0V
850
800
800
1.8
600
-40
VBAT = 1.8V
2.3
2.8
3.3
3.8
4.3
4.8
5.3
-20
VBAT VOLTAGE (V)
0
20
40
60
80
TEMPERATURE (°C)
FIGURE 3. IBAT vs TEMPERATURE
FIGURE 2. IBAT vs VBAT
6
4.4
4.2
5
4.0
IDD1 (µA)
IDD1 (µA)
VBAT = 5.5V
4
VBAT = 2.7V
3
3.8
3.6
3.4
VDD = 3.3V
3.2
2
-40
-20
0
20
40
TEMPERATURE (°C)
60
3.0
2.7
80
3.2
SUPPLY CURRENT (µA)
IDD (µA)
5.2
5.5
VDD = 5.5V
4
2
0.01
4.7
FIGURE 5. IDD1 vs VDD
6
3
4.2
VDD (V)
FIGURE 4. IDD1 vs TEMPERATURE
5
3.7
VDD = 3.3V
0.1
VDD = 2.7V
1
10
100
1k
FREQUENCY OUTPUT (Hz)
FIGURE 6. FOUT vs IDD
7
10k
100k
5.0
FOUT = 32kHz
4.5
4.0
FOUT = 1Hz and 64Hz
3.5
3.0
2.5
-40
-20
0
20
40
TEMPERATURE (°C)
60
80
FIGURE 7. IDD vs TEMPERATURE, 3 DIFFERENT FOUT
FN6659.2
June 23, 2009
ISL12022
Typical Performance Curves Temperature is +25°C unless otherwise specified. (Continued)
110
110
100
100
80
VBAT = 2.7V
70
VDD = 3.3V
60
VBAT = 5.5V
80
IBAT (µA)
IDD (µA)
90
VDD = 5.5V
90
70
60
VBAT = 3.0V
50
VBAT = 1.8V
40
50
30
40
-40
-20
0
20
40
60
80
20
-40
-20
TEMPERATURE (°C)
FIGURE 8. IDD WITH TSE = 1 vs TEMPERATURE
Pin Descriptions
The ISL12022 device is a low power real time clock (RTCs)
with embedded temperature sensors. It contains crystal
frequency compensation circuitry over the operating
temperature range, clock/calendar, power fail and low
battery monitors, brownout indicator, 1 periodic or polled
alarm, intelligent battery-backup switching and 128 Bytes of
battery-backed user SRAM.
X1, X2
The ISL12022’s alarm can be set to any clock/calendar
value for a match, for example, every minute, every Tuesday
or at 5:23 AM on March 21. The alarm status is available by
checking the Status Register, or the device can be
configured to provide a hardware interrupt via the IRQ/FOUT
pin. There is a repeat mode for the alarm allowing a periodic
interrupt every minute, every hour, every day, etc.
The device also offers a backup power input pin. This VBAT
pin allows the device to be backed up by battery or super
capacitor with automatic switchover from VDD to VBAT. The
ISL12022 device is specified for VDD = 2.7V to 5.5V and the
clock/calendar portion of the device remains fully operational
in battery-backup mode down to 1.8V (Standby Mode). The
VBAT level is monitored and reported against preselected
levels. The first report is registered when the VBAT level falls
below 85% of nominal level, the second level is set for 75%.
Battery levels are stored in PWR_VBAT registers.
The ISL12022 offers a “Brownout” alarm once the VDD falls
below a pre-selected trip level. This allows system Micro to
save vital information to memory before complete power
loss. There are six VDD levels that could be selected for
initiation of the Brownout alarm.
8
60
80
FIGURE 9. IBAT with TSE = 1, BTSE = 1 vs TEMPERATURE
General Description
The oscillator uses an external, low cost 32.768kHz crystal.
The real time clock tracks time with separate registers for
hours, minutes and seconds. The device has calendar
registers for date, month, year and day of the week. The
calendar is accurate through 2099, with automatic leap year
correction. In addition, the ISL12022 can be programmed for
automatic Daylight Savings Time (DST) adjustment by
entering local DST information.
0
20
40
TEMPERATURE (°C)
The X1 and X2 pins are the input and output, respectively, of
an inverting amplifier. An external 32.768kHz quartz crystal
is used with the device to supply a timebase for the real time
clock. Internal compensation circuitry with internal
temperature sensor provides frequency corrections for
selected popular crystals to ±5ppm over the operating
temperature range from -40°C to +85°C. (See “Application
Section” on page 25 for recommended crystal). The
ISL12022 allows the user to input via I2C serial bus the
temperature variation profile of an individual crystal. The
oscillator compensation network can also be used to
calibrate the initial crystal timing accuracy to less than 1ppm
error at room temperature. The device can also be driven
directly from a 32.768kHz source at pin X1.
X1
X2
FIGURE 10. RECOMMENDED CRYSTAL CONNECTION
VBAT
This input provides a backup supply voltage to the device.
VBAT supplies power to the device in the event that the VDD
supply fails. Device power will automatically switch to the
VBAT input when VDD drops below the switchover trip level
(VTRIP). This pin can be connected to a battery, a super
capacitor or tied to ground if not used.
IRQ/FOUT (Interrupt Output/Frequency Output)
This dual function pin can be used as an interrupt or
frequency output pin. The IRQ/FOUT mode is selected via
the frequency out control bits of the control/status register. It
is an open drain output.
FN6659.2
June 23, 2009
ISL12022
• Interrupt Mode. The pin provides an interrupt signal
output. This signal notifies a host processor that an alarm
has occurred and requests action. It is an active low
output.
• Frequency Output Mode. The pin outputs a clock signal,
which is related to the crystal frequency. The frequency is
user selectable and enabled via the I2C bus.
Serial Clock (SCL)
The SCL input is used to clock all serial data into and out of
the device. The input buffer on this pin is always active (not
gated). It is disabled when the backup power supply on the
VBAT pin is activated to minimize power consumption.
Serial Data (SDA)
SDA is a bi-directional pin used to transfer data into and out
of the device. It has an open drain output and may be ORed
with other open drain or open collector outputs. The input
buffer is always active (not gated) in normal mode.
An open drain output requires the use of a pull-up resistor.
The output circuitry controls the fall time of the output signal
with the use of a slope controlled pull-down. The circuit is
designed for 400kHz I2C interface speeds. It is disabled
when the backup power supply on the VBAT pin is activated.
Battery-Backup Mode (VBAT) to Normal Mode
(VDD)
The ISL12022 device will switch from the VBAT to VDD mode
when one of the following conditions occurs:
Condition 1:
VDD > VBAT + VBATHYS
where VBATHYS ≈ 50mV
Condition 2:
VDD > VTRIP + VTRIPHYS
where VTRIPHYS ≈ 30mV
These power control situations are illustrated in Figures 11
and 12.
BATTERY-BACKUP
MODE
VDD
VTRIP
2.2V
VBAT
1.8V
VBAT + VBATHYS
VBAT - VBATHYS
FIGURE 11. BATTERY SWITCHOVER WHEN VBAT < VTRIP
VDD, GND
Chip power supply and ground pins. The device will operate
with a power supply from VDD = 2.7V to 5.5VDC. A 0.1µF
capacitor is recommended on the VDD pin to ground.
BATTERY-BACKUP
MODE
Functional Description
VDD
Power Control Operation
The power control circuit accepts a VDD and a VBAT input.
Many types of batteries can be used with Intersil RTC
products. For example, 3.0V or 3.6V Lithium batteries are
appropriate, and battery sizes are available that can power
the ISL12022 for up to 10 years. Another option is to use a
super capacitor for applications where VDD is interrupted for
up to a month. See the “Application Section” on page 25 for
more information.
Normal Mode (VDD) to Battery-Backup Mode
(VBAT)
To transition from the VDD to VBAT mode, both of the
following conditions must be met:
Condition 1:
VBAT
3.0V
VTRIP
2.2V
VTRIP
VTRIP + VTRIPHYS
FIGURE 12. BATTERY SWITCHOVER WHEN VBAT > VTRIP
The I2C bus is deactivated in battery-backup mode to reduce
power consumption. Aside from this, all RTC functions are
operational during battery-backup mode. Except for SCL and
SDA, all the inputs and outputs of the ISL12022 are active
during battery-backup mode unless disabled via the control
register.
The device Time Stamps the switchover from VDD to VBAT
and VBAT to VDD, and the time is stored in tSV2B and tSB2V
registers respectively. If multiple VDD power-down sequences
occur before status is read, the earliest VDD to VBAT
power-down time is stored and the most recent VBAT to VDD
time is stored.
VDD < VBAT - VBATHYS
where VBATHYS ≈ 50mV
Condition 2:
VDD < VTRIP
where VTRIP ≈ 2.2V
Temperature conversion and compensation can be enabled
in battery-backup mode. Bit BTSE in the BETA register
controls this operation, as described in “BETA Register
(BETA)” on page 17.
9
FN6659.2
June 23, 2009
ISL12022
Power Failure Detection
The ISL12022 provides a Real Time Clock Failure Bit
(RTCF) to detect total power failure. It allows users to
determine if the device has powered up after having lost all
power to the device (both VDD and VBAT).
corrects for months having fewer than 31 days and has a bit
that controls 24-hour or AM/PM format. When the ISL12022
powers up after the loss of both VDD and VBAT, the clock will
not begin incrementing until at least one byte is written to the
clock register.
Brownout Detection
Single Event and Interrupt
The ISL12022 monitors the VDD level continuously and
provides warning if the VDD level drops below prescribed
levels. There are six (6) levels that can be selected for the
trip level. These values are 85% below popular VDD levels.
The LVDD bit in the Status Register will be set to “1” when
brownout is detected. Note that the I2C serial bus remains
active unless the Battery VTRIP levels are reached.
The alarm mode is enabled via the MSB bit. Choosing single
event or interrupt alarm mode is selected via the IM bit. Note
that when the frequency output function is enabled, the
alarm function is disabled.
Battery Level Monitor
The ISL12022 has a built in warning feature once the
Back-up battery level drops first to 85% and then to 75% of
the battery’s nominal VBAT level. When the battery voltage
drops to between 85% and 75%, the LBAT85 bit is set in the
status register. When the level drops below 75%, both
LBAT85 and LBAT75 bits are set in the status register.
The battery level monitor is not functional in battery backup
mode. In order to read the monitor bits after powering up
VDD, instigate a battery level measurement by setting the
TSE bit to "1" (BETA register), and then read the bits.
There is a Battery Time Stamp Function available. Once the
VDD is low enough to enable switchover to the battery, the
RTC time/date are written into the TSV2B register. This
information can be read from the TSV2B registers to
discover the point in time of the VDD power-down. If there
are multiple power-down cycles before reading these
registers, the first values stored in these registers will be
retained. These registers will hold the original power-down
value until they are cleared by setting CLRTS = 1 to clear the
registers.
The standard alarm allows for alarms of time, date, day of
the week, month, and year. When a time alarm occurs in
single event mode, the IRQ/FOUT pin will be pulled low and
the alarm status bit (ALM) will be set to “1”.
The pulsed interrupt mode allows for repetitive or recurring
alarm functionality. Hence, once the alarm is set, the device
will continue to alarm for each occurring match of the alarm
and present time. Thus, it will alarm as often as every minute
(if only the nth second is set) or as infrequently as once a
year (if at least the nth month is set). During pulsed interrupt
mode, the IRQ/FOUT pin will be pulled low for 250ms and
the alarm status bit (ALM) will be set to “1”.
The ALM bit can be reset by the user or cleared automatically
using the auto reset mode (see ARST bit). The alarm function
can be enabled/disabled during battery-backup mode using
the FOBATB bit. For more information on the alarm, please
see “ALARM Registers (10h to 15h)” on page 19.
Frequency Output Mode
The ISL12022 has the option to provide a clock output signal
using the IRQ/FOUT open drain output pin. The frequency
output mode is set by using the FO bits to select 15 possible
output frequency values from 1/32Hz to 32kHz. The
frequency output can be enabled/disabled during
battery-backup mode using the FOBATB bit.
The normal power switching of the ISL12022 is designed to
switch into battery-backup mode only if the VDD power is
lost. This will ensure that the device can accept a wide range
of backup voltages from many types of sources while reliably
switching into backup mode.
General Purpose User SRAM
Note that the ISL12022 is not guaranteed to operate with
VBAT < 1.8V. If the battery voltage is expected to drop lower
than this minimum, correct operation of the device,
especially after a VDD power-down cycle, is not guaranteed.
I2C Serial Interface
The ISL12022 provides 128 bytes of user SRAM. The SRAM
will continue to operate in battery-backup mode. However, it
should be noted that the I2C bus is disabled in
battery-backup mode.
The minimum VBAT to insure SRAM is stable is 1.0V. Below
that, the SRAM may be corrupted when VDD power resumes.
The ISL12022 has an I2C serial bus interface that provides
access to the control and status registers and the user
SRAM. The I2C serial interface is compatible with other
industry I2C serial bus protocols using a bi-directional data
signal (SDA) and a clock signal (SCL).
Real Time Clock Operation
Oscillator Compensation
The Real Time Clock (RTC) uses an external 32.768kHz
quartz crystal to maintain an accurate internal representation
of second, minute, hour, day of week, date, month, and year.
The RTC also has leap-year correction. The clock also
The ISL12022 provides both initial timing correction and
temperature correction due to variation of the crystal
oscillator. Analog and digital trimming control is provided for
initial adjustment, and a temperature compensation function
is provided to automatically correct for temperature drift of
10
FN6659.2
June 23, 2009
ISL12022
the crystal. Initial values are preset and recalled on initial
power-up for the Initial AT and DT settings (IATR, IDTR),
temperature coefficient (ALPHA), crystal capacitance
(BETA), and the crystal turn-over temperature (XTO). These
initial values are typical of units available on the market,
although the user may program specific values after testing
for best accuracy. The function can be enabled/disabled at
any time and can be used in battery mode as well.
6. Daylight Savings Time (8 bytes): 20h to 27h.
7. TEMP (2 bytes): 28h to 29h
8. Crystal Net PPM Correction, NPPM (2 bytes): 2Ah, 2Bh
9. Crystal Turnover Temperature, XT0 (1 byte): 2Ch
10. Crystal ALPHA at high temperature, ALPHA_H (1 byte):
2Dh
11. Scratch Pad (2 bytes): Address 2Eh and 2Fh
Write capability is allowable into the RTC registers (00h to
06h) only when the WRTC bit (bit 6 of address 08h) is set to
“1”. A multi-byte read or write operation should be limited to
one section per operation for best RTC time keeping
performance.
Register Descriptions
The battery-backed registers are accessible following a
slave byte of “1101111x” and reads or writes to addresses
[00h:2Fh]. The defined addresses and default values are
described in the Table 1. The battery backed general
purpose SRAM has a different slave address (1010111x), so
it is not possible to read/write that section of memory while
accessing the registers.
A register can be read by performing a random read at any
address at any time. This returns the contents of that register
location. Additional registers are read by performing a
sequential read. For the RTC and Alarm registers, the read
instruction latches all clock registers into a buffer, so an
update of the clock does not change the time being read. At
the end of a read, the master supplies a stop condition to
end the operation and free the bus. After a read, the address
remains at the previous address +1 so the user can execute
a current address read and continue reading the next
register. When the previous address is 2Fh, the next
address will wrap around to 00h.
REGISTER ACCESS
The contents of the registers can be modified by performing
a byte or a page write operation directly to any register
address.
The registers are divided into 8 sections. They are:
1. Real Time Clock (7 bytes): Address 00h to 06h.
2. Control and Status (9 bytes): Address 07h to 0Fh.
It is not necessary to set the WRTC bit prior to writing into
the control and status, alarm, and user SRAM registers.
3. Alarm (6 bytes): Address 10h to 15h.
4. Time Stamp for Battery Status (5 bytes): Address 16h to
1Ah.
5. Time Stamp for VDD Status (5 bytes): Address 1Bh to
1Fh.
TABLE 1. REGISTER MEMORY MAP
BIT
REG
NAME
7
6
5
4
3
2
1
0
RANGE
DEFAULT
00h
SC
0
SC22
SC21
SC20
SC13
SC12
SC11
SC10
0 to 59
00h
01h
MN
0
MN22
MN21
MN20
MN13
MN12
MN11
MN10
0 to 59
00h
02h
HR
MIL
0
HR21
HR20
HR13
HR12
HR11
HR10
0 to 23
00h
DT
0
0
DT21
DT20
DT13
DT12
DT11
DT10
1 to 31
01h
MO
0
0
0
MO20
MO13
MO12
MO11
MO10
1 to 12
01h
05h
YR
YR23
YR22
YR21
YR20
YR13
YR12
YR11
YR10
0 to 99
00h
06h
DW
0
0
0
0
0
DW2
DW1
DW0
0 to 6
00h
07h
SR
BUSY
OSCF
DSTADJ
ALM
LVDD
LBAT85
LBAT75
RTCF
N/A
01h
08h
INT
ARST
WRTC
IM
FOBATB
FO3
FO2
FO1
FO0
N/A
01h
09h
PWR_VDD
CLRTS
0Ah
PWR_VBAT
ADDR. SECTION
03h
RTC
04h
0Bh
D
D
D
D
VDDTrip2
VDDTrip1
VDDTrip0
N/A
00h
RESEALB
VB85Tp2
VB85Tp1
VB85Tp0
VB75Tp2
VB75Tp1
VB75Tp0
N/A
00h
ITRO
IDTR01
IDTR00
IATR05
IATR04
IATR03
IATR02
IATR01
IATR00
N/A
20h
0Ch
ALPHA
D
ALPHA6
ALPHA5
ALPHA4
ALPHA3
ALPHA2
ALPHA1
ALPHA0
N/A
46h
0Dh
BETA
TSE
BTSE
BTSR
BETA4
BETA3
BETA2
BETA1
BETA0
N/A
00h
0Eh
FATR
0
0
FFATR5
FATR4
FATR3
FATR2
FATR1
FATR0
N/A
00h
0Fh
FDTR
0
0
0
FDTR4
FDTR3
FDTR2
FDTR1
FDTR0
N/A
00h
CSR
11
FN6659.2
June 23, 2009
ISL12022
TABLE 1. REGISTER MEMORY MAP (Continued)
BIT
REG
NAME
7
6
5
4
3
2
1
0
RANGE
DEFAULT
10h
SCA0
ESCA0
SCA022
SCA021
SCA020
SCA013
SCA012
SCA011
SCA010
00 to 59
00h
11h
MNA0
EMNA0
MNA022
MNA021
MNA020
MNA013
MNA012
MNA011
MNA010
00 to 59
00h
HRA0
EHRA0
D
HRA021
HRA020
HRA013
HRA012
HRA011
HRA010
0 to 23
00h
DTA0
EDTA0
D
DTA021
DTA020
DTA013
DTA012
DTA011
DTA010
01 to 31
00h
14h
MOA0
EMOA00
D
D
MOA020
MOA013
MOA012
MOA011
MOA010
01 to 12
00h
15h
DWA0
EDWA0
D
D
D
D
DWA02
DWA01
DWA00
0 to 6
00h
ADDR. SECTION
12h
13h
ALARM
16h
VSC
0
VSC22
VSC21
VSC20
VSC13
VSC12
VSC11
VSC10
0 to 59
00h
17h
VMN
0
VMN22
VMN21
VMN20
VMN13
VMN12
VMN11
VMN10
0 to 59
00h
VHR
VMIL
0
VHR21
VHR20
VHR13
VHR12
VHR11
VHR10
0 to 23
00h
19h
VDT
0
0
VDT21
VDT20
VDT13
VDT12
VDT11
VDT10
1 to 31
00h
1Ah
VMO
0
0
0
VMO20
VMO13
VMO12
VMO11
VMO10
1 to 12
00h
1Bh
BSC
0
BSC22
BSC21
BSC20
BSC13
BSC12
BSC11
BSC10
0 to 59
00h
1Ch
BMN
0
BMN22
BMN21
BMN20
BMN13
BMN12
BMN11
BMN10
0 to 59
00h
BHR
BMIL
0
BHR21
BHR20
BHR13
BHR12
BHR11
BHR10
0 to 23
00h
18h
1Dh
TSV2B
TSB2V
1Eh
BDT
0
0
BDT21
BDT20
BDT13
BDT12
BDT11
BDT10
1 to 31
00h
1Fh
BMO
0
0
0
BMO20
BMO13
BMO12
BMO11
BMO10
1 to 12
00h
20h
DstMoFd
DSTE
D
D
DstMoFd20 DstMoFd13 DstMoFd12 DstMoFd11 DstMoFd10
1 to 12
00h
21h
DstDwFd
D
DstDwFdE
DstWkFd12 DstWkFd11 DstWkFd10 DstDwFd12 DstDwFd11 DstDwFd10
0 to 6
00h
22h
DstDtFd
D
D
DstDtFd21
DstDtFd20
DstDtFd13
DstDtFd12
DstDtFd11
DstDtFd10
1 to 31
00h
23h
DstHrFd
D
D
DstHrFd21
DstHrFd20
DstHrFd13
DstHrFd12
DstHrFd11
DstHrFd10
0 to 23
00h
DstMoRv
D
D
D
XDstMoRv2 DstMoRv13 DstMoR12v DstMoRv11 DstMoRv10
0
01 to 12
00h
25h
DstDwRv
D
DstDwRvE
0 to 6
00h
26h
DstDtRv
D
D
DstDtRv21
DstDtRv20
DstDtRv13
DstDtRv12
DstDtRv11
DstDtRv10
01 to 31
00h
27h
DstHrRv
D
D
DstHrRv21
DstHrRv20
DstHrRv13
DstHrRv12
DstHrRv11
DstHrRv10
0 to 23
00h
24h
DSTCR
28h
29h
TEMP
2Ah
2Bh
NPPM
DstWkrv12 DstWkRv11 DstWkRv10 DstDwRv12 DstDwRv11 DstDwRv10
TK0L
TK07
TK06
TK05
TK04
TK03
TK02
TK01
TK00
00 to FF
00h
TK0M
0
0
0
0
0
0
TK09
TK08
00 to 03
00h
NPPML
NPPM7
NPPM6
NPPM5
NPPM4
NPPM3
NPPM2
NPPM1
NPPM0
00 to FF
00h
NPPMH
0
0
0
0
0
NPPM10
NPPM9
NPPM8
00 to 07
00h
2Ch
XT0
XT0
D
D
D
XT4
XT3
XT2
XT1
XT0
00 to FF
00h
2Dh
ALPHAH
ALPHAH
D
ALP_H6
ALP_H5
ALP_H4
ALP_H3
ALP_H2
ALP_H1
ALP_H0
00 to 7F
46h
2Eh
GPM
GPM1
GPM17
GPM16
GPM15
GPM14
GPM13
GPM12
GPM11
GPM10
00 to FF
00h
GPM2
GPM27
GPM26
GPM25
GPM24
GPM23
GPM22
GPM21
GPM20
00 to FF
00h
2Fh
12
FN6659.2
June 23, 2009
ISL12022
Real Time Clock Registers
OSCILLATOR FAIL BIT (OSCF)
Oscillator Fail Bit indicates that the oscillator has stopped.
Addresses [00h to 06h]
DAYLIGHT SAVINGS TIME CHANGE BIT (DSTADJ)
RTC REGISTERS (SC, MN, HR, DT, MO, YR, DW)
These registers depict BCD representations of the time. As
such, SC (Seconds) and MN (Minutes) range from 0 to 59,
HR (Hour) can either be a 12-hour or 24-hour mode, DT
(Date) is 1 to 31, MO (Month) is 1 to 12, YR (Year) is 0 to 99,
and DW (Day of the Week) is 0 to 6.
DSTADJ is the Daylight Savings Time Adjusted Bit. It
indicates the daylight saving time forward adjustment has
happened. If a DST Forward event happens, DSTADJ will be
set to “1”. The DSTADJ bit will stay high after the DSTFD
event happens, and will be reset to “0” when the DST
Reverse event happens.
The DW register provides a Day of the Week status and uses
three bits DW2 to DW0 to represent the seven days of the
week. The counter advances in the cycle 0-1-2-3-4-5-6-0-12-… The assignment of a numerical value to a specific day
of the week is arbitrary and may be decided by the system
software designer. The default value is defined as “0”.
DSTADJ can be set to “1” for instances where the RTC
device is initialized during the DST Forward period. The
DSTE bit must be enabled when the RTC time is more than
one hour before the DST Forward or DST Reverse event
time setting, or the DST event correction will not happen.
24 HOUR TIME
If the MIL bit of the HR register is “1”, the RTC uses a
24-hour format. If the MIL bit is “0”, the RTC uses a 12-hour
format and HR21 bit functions as an AM/PM indicator with a
“1” representing PM. The clock defaults to 12-hour format
time with HR21 = “0”.
LEAP YEARS
Leap years add the day February 29 and are defined as those
years that are divisible by 4. Years divisible by 100 are not leap
years, unless they are also divisible by 400. This means that
the year 2000 is a leap year and the year 2100 is not. The
ISL12022 does not correct for the leap year in the year 2100.
Control and Status Registers (CSR)
Addresses [07h to 0Fh]
The Control and Status Registers consist of the Status
Register, Interrupt and Alarm Register, Analog Trimming and
Digital Trimming Registers.
Status Register (SR)
The Status Register is located in the memory map at
address 07h. This is a volatile register that provides either
control or status of RTC failure (RTCF), Battery Level
Monitor (LBAT85, LBAT75), alarm trigger, Daylight Savings
Time, crystal oscillator enable and temperature conversion
in progress bit.
TABLE 2. STATUS REGISTER (SR)
ADDR
07h
7
6
5
4
3
2
1
0
BUSY OSCF DSTDJ ALM LVDD LBAT85 LBAT75 RTCF
BUSY BIT (BUSY)
Busy Bit indicates temperature sensing is in progress. In this
mode, Alpha, Beta and ITRO registers are disabled and
cannot be accessed.
13
DSTADJ is reset to “0” upon power-up. It will reset to ”0”
when the DSTE bit in Register 15h is set to “0” (DST
disabled), but no time adjustment will happen.
ALARM BIT (ALM)
This bit announces if the alarm matches the real time clock. If
there is a match, the respective bit is set to “1”. This bit can be
manually reset to “0” by the user or automatically reset by
enabling the auto-reset bit (see ARST bit). A write to this bit in
the SR can only set it to “0”, not “1”. An alarm bit that is set by
an alarm occurring during an SR read operation will remain
set after the read operation is complete.
LOW VDD INDICATOR BIT (LVDD)
This bit indicates when VDD has dropped below the
pre-selected trip level (Brownout Mode). The trip points for
the brownout levels are selected by three bits: VDD Trip2,
VDD Trip1 and VDD Trip0 in PWR_ VDD registers. The
LVDD detection is only enabled in VDD mode and the
detection happens in real time. The LVDD bit is set
whenever the VDD has dropped below the pre-selected trip
level, and self clears whenever the VDD is above the preselected trip level.
LOW BATTERY INDICATOR 85% BIT (LBAT85)
In Normal Mode (VDD), this bit indicates when the battery
level has dropped below the pre-selected trip levels. The trip
points are selected by three bits: VB85Tp2, VB85Tp1 and
VB85Tp0 in the PWR_VBAT registers. The LBAT85
detection happens automatically once every minute when
seconds register reaches 59. The detection can also be
manually triggered by setting the TSE bit in BETA register to
“1”. The LBAT85 bit is set when the VBAT has dropped below
the pre-selected trip level, and will self clear when the VBAT
is above the pre-selected trip level at the next detection
cycle either by manual or automatic trigger.
In Battery Mode (VBAT), this bit indicates the device has
entered into battery mode by polling once every 10 minutes.
The LBAT85 detection happens automatically once when the
minute register reaches x9h or x0h minutes.
FN6659.2
June 23, 2009
ISL12022
Example - When the LBAT85 is Set To “1” In Battery Mode:
AUTOMATIC RESET BIT (ARST)
The minute the register changes to 19h when the device is in
battery mode, the LBAT85 is set to “1” the next time the
device switches back to Normal Mode.
This bit enables/disables the automatic reset of the ALM,
LVDD, LBAT85, and LBAT75 status bits only. When ARST
bit is set to “1”, these status bits are reset to “0” after a valid
read of the respective status register (with a valid STOP
condition). When the ARST is cleared to “0”, the user must
manually reset the ALM, LVDD, LBAT85, and LBAT75 bits.
Example - When the LBAT85 Remains at “0” In Battery
Mode:
If the device enters into battery mode after the minute
register reaches 20h and switches back to Normal Mode
before the minute register reaches 29h, then the LBAT85 bit
will remain at “0” the next time the device switches back to
Normal Mode.
LOW BATTERY INDICATOR 75% BIT (LBAT75)
In Normal Mode (VDD), this bit indicates when the battery
level has dropped below the pre-selected trip levels. The trip
points are selected by three bits: VB75Tp2, VB75Tp1 and
VB75Tp0 in the PWR_VBAT registers. The LBAT75
detection happens automatically once every minute when
seconds register reaches 59. The detection can also be
manually triggered by setting the TSE bit in BETA register to
“1”. The LBAT75 bit is set when the VBAT has dropped below
the pre-selected trip level, and will self clear when the VBAT
is above the pre-selected trip level at the next detection
cycle either by manual or automatic trigger.
In Battery Mode (VBAT), this bit indicates the device has
entered into battery mode by polling once every 10 minutes.
The LBAT85 detection happens automatically once when the
minute register reaches x9h or x0h minutes.
Example - When the LBAT75 is Set to “1” in Battery Mode:
The minute register changes to 30h when the device is in
battery mode, the LBAT75 is set to “1” the next time the
device switches back to Normal Mode.
Example - When the LBAT75 Remains at “0” in Battery
Mode:
If the device enters into battery mode after the minute register
reaches 49h and switches back to Normal Mode before
minute register reaches 50h, then the LBAT75 bit will remain
at “0” the next time the device switches back to Normal Mode.
REAL TIME CLOCK FAIL BIT (RTCF)
This bit is set to a “1” after a total power failure. This is a read
only bit that is set by hardware (ISL12022 internally) when
the device powers up after having lost all power (defined as
VDD = 0V and VBAT = 0V). The bit is set regardless of
whether VDD or VBAT is applied first. The loss of only one of
the supplies does not set the RTCF bit to “1”. The first valid
write to the RTC section after a complete power failure
resets the RTCF bit to “0” (writing one byte is sufficient).
WRITE RTC ENABLE BIT (WRTC)
The WRTC bit enables or disables write capability into the
RTC Timing Registers. The factory default setting of this bit
is “0”. Upon initialization or power-up, the WRTC must be set
to “1” to enable the RTC. Upon the completion of a valid
write (STOP), the RTC starts counting. The RTC internal
1Hz signal is synchronized to the STOP condition during a
valid write cycle.
INTERRUPT/ALARM MODE BIT (IM)
This bit enables/disables the interrupt mode of the alarm
function. When the IM bit is set to “1”, the alarm will operate
in the interrupt mode, where an active low pulse width of
250ms will appear at the IRQ/FOUT pin when the RTC is
triggered by the alarm, as defined by the alarm registers
(0Ch to 11h). When the IM bit is cleared to “0”, the alarm will
operate in standard mode, where the IRQ/FOUT pin will be
set low until the ALM status bit is cleared to “0”.
TABLE 4.
IM BIT
INTERRUPT/ALARM FREQUENCY
0
Single Time Event Set By Alarm
1
Repetitive/Recurring Time Event Set By Alarm
FREQUENCY OUTPUT AND INTERRUPT BIT (FOBATB)
This bit enables/disables the IRQ/FOUT pin during
battery-backup mode (i.e. VBAT power source active). When
the FOBATB is set to “1”, the IRQ/FOUT pin is disabled
during battery-backup mode. This means that both the
frequency output and alarm output functions are disabled.
When the FOBATB is cleared to “0”, the IRQ/FOUT pin is
enabled during battery-backup mode. Note that the open
drain IRQ/FOUT pin will need a pull-up to the battery voltage
to operate in battery-backup mode.
FREQUENCY OUT CONTROL BITS (FO<3:0>)
These bits enable/disable the frequency output function and
select the output frequency at the IRQ/FOUT pin. See Table 5
for frequency selection. Default for the ISL12022 is
FO<3:0> = 1h, or 32.768kHz output. When the frequency mode
is enabled, it will override the alarm mode at the IRQ/FOUT pin.
Interrupt Control Register (INT)
TABLE 3. INTERRUPT CONTROL REGISTER (INT)
ADDR
08h
7
6
ARST WRTC
5
IM
4
3
2
1
0
FOBATB FO3 FO2 FO1 FO0
14
FN6659.2
June 23, 2009
ISL12022
Battery Voltage Trip Voltage Register (PWR_VBAT)
TABLE 5. FREQUENCY SELECTION OF IRQ/FOUT PIN
FREQUENCY,
FOUT
UNITS
FO3
FO2
FO1
FO0
This register controls the trip points for the two VBAT alarms,
with levels set to approximately 85% and 75% of the nominal
battery level.
0
Hz
0
0
0
0
32768
Hz
0
0
0
1
4096
Hz
0
0
1
0
1024
Hz
0
0
1
1
64
Hz
0
1
0
0
RESEAL BIT (RESEALB)
32
Hz
0
1
0
1
16
Hz
0
1
1
0
8
Hz
0
1
1
1
4
Hz
1
0
0
0
2
Hz
1
0
0
1
This is the Reseal bit for actively disconnecting VBAT pin from
the internal circuitry. Setting this bit allows the device to
disconnect the battery and eliminate standby current drain
while the device is unused. Once VDD is powered up, this bit is
reset and the VBAT pin is then connected to the internal
circuitry.
1
Hz
1
0
1
0
1/2
Hz
1
0
1
1
1/4
Hz
1
1
0
0
1/8
Hz
1
1
0
1
1/16
Hz
1
1
1
0
1/32
Hz
1
1
1
1
TABLE 7.
ADDR 7
09h
6
5
4
3
CLRTS
0
0
0
0
2
1
0
This bit clears Time Stamp VDD to Battery (TSV2B) and Time
Stamp Battery to VDD Registers (TSB2V). The default setting
is 0 (CLRTS = 0) and the Enabled setting is 1 (CLRTS = 1).
VDD Brownout Trip Voltage BITS (VDDTrip<2:0)
These bits set the 6 trip levels for the VDD alarm, indicating
that VDD has dropped below a preset level. In this event, the
LVDD bit in the Status Register is set to “1”. See Table 6.
VDDTrip2
VDDTrip1
VDDTrip0
TRIP
VOLTAGE
(V)
0
0
0
2.295
0
0
1
2.550
0
1
0
2.805
0
1
1
3.060
1
0
0
4.250
1
0
1
4.675
15
3
2
1
Three bits select the first alarm (85% of Nominal VBAT) level for
the battery voltage monitor. There are total of 7 levels that could
be selected for the first alarm. Any of the of levels could be
selected as the first alarm with no reference as to nominal
Battery voltage level. See Table 8.
VDDTrip2 VDDTrip1 VDDTrip0
TABLE 6. VDD TRIP LEVELS
4
BATTERY LEVEL MONITOR TRIP BITS (VB85TP<2:0>)
Clear Time Stamp Bit (CLRTS)
7
5
The application for this bit involves placing the chip on a
board with a battery and testing the board. Once the board is
tested and ready to ship, it is desirable to disconnect the
battery to keep it fresh until the board or unit is placed into
final use. Setting RESEALB = “1” initiates the battery
disconnect, and after VDD power is cycled down and up
again, the RESEAL bit is cleared to “0”.
POWER SUPPLY CONTROL REGISTER (PWR_VDD)
ADDR
6
0
D RESEALB VB85Tp2 VB85Tp1 VB85Tp0 VB75Tp2 VB75Tp1 VB75Tp0
0Ah
TABLE 8. VB85T ALARM LEVEL
VB85Tp2
VB85Tp1
VB85Tp0
BATTERY
ALARM TRIP
LEVEL
(V)
0
0
0
2.125
0
0
1
2.295
0
1
0
2.550
0
1
1
2.805
1
0
0
3.060
1
0
1
4.250
1
1
0
4.675
BATTERY LEVEL MONITOR TRIP BITS (VB75TP<2:0>)
Three bits select the second alarm (75% of Nominal VBAT)
level for the battery voltage monitor. There are total of 7 levels
that could be selected for the second alarm. Any of the of levels
could be selected as the second alarm with no reference as to
nominal Battery voltage level. See Table 9.
FN6659.2
June 23, 2009
ISL12022
Aging adjustment is normally a few ppm and can be handled
by writing to the IATR section.
TABLE 9. BATTERY LEVEL MONITOR TRIP BITS
(VB75TP<2:0>)
VB75Tp2
VB75Tp1
VB75Tp0
BATTERY
ALARM TRIP
LEVEL
(V)
0
0
0
1.875
0
0
1
0
1
0
TABLE 12. IATR0 TRIMMING RANGE
IATR05 IATR04 IATR03 IATR02 IATR01 IATR00
TRIMMING
RANGE
0
0
0
0
0
0
+32
0
0
0
0
0
1
+31
2.025
0
0
0
0
1
0
+30
2.250
0
0
0
0
1
1
+29
0
0
0
1
0
0
+28
0
0
0
1
0
1
+27
0
1
1
2.475
1
0
0
2.700
0
0
0
1
1
0
+26
1
0
1
3.750
0
0
0
1
1
1
+25
0
0
1
0
0
0
+24
0
0
1
0
0
1
+23
0
0
1
0
1
0
+22
0
0
1
0
1
1
+21
0
0
1
1
0
0
+20
0
0
1
1
0
1
+19
0
0
1
1
1
0
+18
0
0
1
1
1
1
+17
0
1
0
0
0
0
+16
0
1
0
0
0
1
+15
0
1
0
0
1
0
+14
0
1
0
0
1
1
+13
AGING AND INITIAL TRIM DIGITAL TRIMMING BITS
(IDTR0<1:0>)
0
1
0
1
0
0
+12
0
1
0
1
0
1
+11
These bits allow ±30.5ppm initial trimming range for the
crystal frequency. This is meant to be a coarse adjustment if
the range needed is outside that of the IATR control.
See Table 10. The IDTR0 register should only be changed
while the TSE (Temp Sense Enable) bit is “0”.
0
1
0
1
1
0
+10
0
1
0
1
1
1
+9
0
1
1
0
0
0
+8
0
1
1
0
0
1
+7
0
1
1
0
1
0
+6
0
1
1
0
1
1
+5
0
1
1
1
0
0
+4
0
1
1
1
0
1
+3
0
1
1
1
1
0
+2
0
1
1
1
1
1
+1
1
0
0
0
0
0
0
1
0
0
0
0
1
-1
1
0
0
0
1
0
-2
1
0
0
0
1
1
-3
1
0
0
1
0
0
-4
1
0
0
1
0
1
-5
1
0
0
1
1
0
-6
1
0
0
1
1
1
-7
1
0
1
0
0
0
-8
1
0
1
0
0
1
-9
1
0
1
0
1
0
-10
1
0
1
0
1
1
-11
1
0
1
1
0
0
-12
1
0
1
1
0
1
-13
1
0
1
1
1
0
-14
1
0
1
1
1
1
-15
1
1
0
0
0
0
-16
1
1
0
0
0
1
-17
1
1
0
4.125
Initial AT and DT setting Register (ITRO)
These bits are used to trim the initial error (at room
temperature) of the crystal. Both Digital Trimming (DT) and
Analog Trimming (AT) methods are available. The digital
trimming uses clock pulse skipping and insertion for
frequency adjustment. Analog trimming uses load
capacitance adjustment to pull the oscillator frequency. A
range of +62.5ppm to -61.5ppm is possible with combined
digital and analog trimming.
TABLE 10. IDTR0 TRIMMING RANGE
IDTR01
IDTR00
0
0
TRIMMING RANGE
Default/Disabled
0
1
+30.5ppm
1
0
0ppm
1
1
-30.5ppm
AGING AND INITIAL ANALOG TRIMMING BITS
(IATR0 <5:0>)
The analog trimming register allows +32ppm to -31ppm
adjustment in 1ppm/bit increments. This enables fine
frequency adjustment for trimming initial crystal accuracy error
or to correct for aging drift. The IATR0 register should only be
changed while the TSE (Temp Sense Enable) bit is “0”.
TABLE 11. INITIAL AT AND DT SETTING REGISTER
ADDR
0Bh
7
6
5
4
3
2
1
0
IDTR01 IDTR00 IATR05 IATR04 IATR03 IATR02 IATR01 IATR00
16
FN6659.2
June 23, 2009
ISL12022
TEMPERATURE SENSOR ENABLED BIT (TSE)
TABLE 12. IATR0 TRIMMING RANGE (Continued)
IATR05 IATR04 IATR03 IATR02 IATR01 IATR00
This bit enables the Temperature Sensing operation, including
the temperature sensor, A/D converter and AT/DT register
adjustment. The default mode after power-up is disabled
(TSE = 0). To enable the operation, TSE should be set to 1
(TSE = 1). When the temperature sensor is disabled, the initial
values for IATR and IDTR registers are used for frequency
control.
TRIMMING
RANGE
1
1
0
0
1
0
-18
1
1
0
0
1
1
-19
1
1
0
1
0
0
-20
1
1
0
1
0
1
-21
1
1
0
1
1
0
-22
1
1
0
1
1
1
-23
1
1
1
0
0
0
-24
1
1
1
0
0
1
-25
1
1
1
0
1
0
-26
1
1
1
0
1
1
-27
1
1
1
1
0
0
-28
1
1
1
1
0
1
-29
1
1
1
1
1
0
-30
1
1
1
1
1
1
-31
All changes to the IDTR, IATR, ALPHA and BETA registers
must be made with TSE = 0. After loading the new values,
TSE can be enabled and the new values are used. When TSE
is set to 1, the temperature conversion cycle begins and will
end when two temperature conversions are completed. The
average of the two conversions is in the TEMP registers. The
total time for temperature sense and conversion is
approximately 22ms from the time TSE = 1 write is completed.
TEMP SENSOR CONVERSION IN BATTERY MODE BIT
(BTSE)
Note that setting the IATR to the lowest settings (-31ppm)
with the default 32kHz output can cause the oscillator
frequency to become unstable on power-up. The lowest
settings for IATR should be avoided to insure oscillator
frequency integrity. If the lowest IATR settings are needed,
then the user is advised to disable the FOUT and enable
again to insure placing the oscillator in a stable condition.
This bit enables the Temperature Sensing and Correction in
battery mode. BTSE = 0 (default) no conversion, Temp
Sensing or Compensation in battery mode. BTSE = 1
indicates Temp Sensing and Compensation enabled in battery
mode. The BTSE is disabled when the battery voltage is lower
than 2.7V. No temperature compensation will take place with
VBAT<2.7V.
ALPHA REGISTER (ALPHA)
TABLE 13. ALPHA REGISTER
ADDR
7
0Ch
D
6
5
4
3
2
1
0
ALPHA6 ALPHA5 ALPHA4 ALPHA3 ALPHA2 ALPHA1 ALPHA0
The Alpha variable is 8 bits and is defined as the
temperature coefficient of Crystal from -40°C to T0, or the
Alpha Cold (There is an Alpha Hot register that must be
programmed as well). It is normally given in units of
ppm/°C2, with a typical value of -0.034. The ISL12022
device uses a scaled version of the absolute value of this
coefficient in order to get an integer value. Therefore,
Alpha<7:0> is defined as the (|Actual Alpha Value| x 2048)
and converted to binary. For example, a crystal with Alpha of
-0.034ppm/°C2 is first scaled (|2048*(-0.034)| = 70d) and
then converted to a binary number of 01000110b.
The practical range of Actual Alpha values is from
-0.020 to -0.060.
The ALPHA register should only be changed while the TSE
(Temp Sense Enable) bit is “0”. Note that both the ALPHA
and the ALPHA Hot registers need to be programmed with
values for full range temperature compensation.
BETA Register (BETA)
TABLE 14.
ADDR
0Dh
7
TSE
6
5
4
3
2
1
0
BTSE BTSR BETA4 BETA3 BETA2 BETA1 BETA0
17
FREQUENCY OF TEMPERATURE SENSING AND
CORRECTION BIT (BTSR)
This bit controls the frequency of Temperature Sensing and
Correction. BTSR = 0 default mode is every 10 minutes,
BTSR = 1 is every 1.0 minute. Note that BTSE has to be
enabled in both cases. See Table 15.
TABLE 15. FREQUENCY OF TEMPERATURE SENSING AND
CORRECTION BIT
BTSE
BTSR
TC PERIOD IN BATTERY MODE
0
0
OFF
0
1
OFF
1
0
10 Minutes
1
1
1 Minute
The temperature measurement conversion time is the same
for battery mode as for VDD mode, approximately 22ms. The
battery mode current will increase during this conversion time
to typically 68µA. The average increase in battery current is
much lower than this due to the small duty cycle of the
ON-time versus OFF-time for the conversion.
To figure the average increase in battery current, we take the
the change in current times the duty cycle. For the 1 minute
temperature period the average current is shown in
Equation 1:
0.022s
ΔI BAT = ------------------ × 68μA = 250nA
60s
(EQ. 1)
FN6659.2
June 23, 2009
ISL12022
For the 10 minute temperature period the average current is
shown in Equation 2:
TABLE 16. BETA VALUES (Continued)
BETA<4:0>
AT STEP ADJUSTMENT
(EQ. 2)
10010
1.1875
If the application has a stable temperature environment that
doesn’t change quickly, the 10 minute option will work well
and the backup battery lifetime impact is minimized. If quick
temperature variations are expected (multiple cycles of more
than 10° within an hour), then the 1 minute option should be
considered and the slightly higher battery current figured into
overall battery life.
10011
1.2500
10100
1.3125
10101
1.3750
10110
1.4375
10111
1.5000
11000
1.5625
11001
1.6250
11010
1.6875
11011
1.7500
11100
1.8125
11101
1.8750
11110
1.9375
11111
2.0000
0.022s
ΔI BAT = ------------------ × 68μA = 25nA
600s
GAIN FACTOR OF AT BIT (BETA<4:0>)
Beta is specified to take care of the Cm variations of the
crystal. Most crystals specify Cm around 2.2fF. For example,
if Cm > 2.2fF, the actual AT steps may reduce from
1ppm/step to approximately 0.80ppm/step. Beta is then used
to adjust for this variation and restore the step size to
1ppm/step.
BETA values are limited in the range from 01000 to 11111 as
shown in Table 16. To use Table 16, the device is tested at
two AT settings as shown in Equation 3:
BETAVALUES = ( AT ( max ) – AT ( min ) )/63
(EQ. 3)
where:
AT(max) = FOUT in ppm (at AT = 00H) and
Final Analog Trimming Register (FATR)
This register shows the final setting of AT after temperature
correction. It is read-only; the user cannot overwrite a value to
this register. This value is accessible as a means of monitoring
the temperature compensation function. See Table 17.
AT(min) = FOUT in ppm (at AT = 3FH).
TABLE 17. FINAL ANALOG TRIMMING REGISTER
The BETA VALUES result is indexed in the right hand
column and the resulting Beta factor (for the register) is in
the same row in the left column.
The value for BETA should only be changed while the TSE
(Temperature Sense Enable) bit is “0”. The procedure for
writing the BETA register involves two steps. First, write the
new value of BETA with TSE = 0. Then write the same value
of BETA with TSE = 1. This will insure the next temperature
sense cycle will use the new BETA value.
TABLE 16. BETA VALUES
ADDR
7
6
0Eh
0
0
5
4
3
2
1
FATR5 FATR4 FATR3 FATR2 FATR1 FATR0
Final Digital Trimming Register (FDTR)
This Register shows the final setting of DT after temperature
correction. It is read-only; the user cannot overwrite a value
to this register. The value is accessible as a means of
monitoring the temperature compensation function. The
corresponding clock adjustment values are shown in
Table 19. The DT setting has both positive and negative
settings to adjust for any offset in the crystal.
BETA<4:0>
AT STEP ADJUSTMENT
01000
0.5000
00111
0.5625
ADDR
7
6
5
00110
0.6250
0Fh
0
0
0
00101
0.6875
00100
0.7500
00011
0.8125
00010
0.8750
FDTR<2:0>
DECIMAL
ppm
ADJUSTMENT
00001
0.9375
00000
0
0
00000
1.0000
00001
1
30.5
10000
1.0625
00010
2
61
10001
1.1250
.
18
0
TABLE 18. FINAL DIGITAL TRIMMING REGISTER
4
3
2
1
0
FDTR4 FDTR3 FDTR2 FDTR1 FDTR0
TABLE 19. CLOCK ADJUSTMENT VALUES FOR FINAL
DIGITAL TRIMMING REGISTER
FN6659.2
June 23, 2009
ISL12022
TABLE 19. CLOCK ADJUSTMENT VALUES FOR FINAL
DIGITAL TRIMMING REGISTER (Continued)
FDTR<2:0>
DECIMAL
ppm
ADJUSTMENT
00011
3
91.5
00100
4
122
00101
5
152.5
00110
6
183
00111
7
213.5
01000
8
244
01001
9
274.5
01010
10
305
10000
0
0
10001
-1
-30.5
10010
-2
-61
10011
-3
-91.5
output will now be pulsed each time an alarm occurs. This
means that once the interrupt mode alarm is set, it will
continue to alarm for each occurring match of the alarm
and present time. This mode is convenient for hourly or
daily hardware interrupts in microcontroller applications
such as security cameras or utility meter reading.
To clear a single event alarm, the ALM bit in the status
register must be set to “0” with a write. Note that if the ARST
bit is set to 1 (address 08h, bit 7), the ALM bit will
automatically be cleared when the status register is read.
Following are examples of both Single Event and periodic
Interrupt Mode alarms.
Example 1
• Alarm set with single interrupt (IM = ”0”)
• A single alarm will occur on January 1 at 11:30 a.m.
• Set Alarm registers as follows:
ALARM
REGISTER 7
BIT
6
5
4
3
2
1
0
HEX
DESCRIPTION
10100
-4
-122
10101
-5
-152.5
SCA0
0
0
0
0
0
0
0
0
00h Seconds disabled
10110
-6
-183
MNA0
1
0
1
1
0
0
0
0
B0h Minutes set to 30,
enabled
10111
-7
-213.5
HRA0
1
0
0
1
0
0
0
1
11000
-8
-244
91h Hours set to 11,
enabled
11001
-9
-274.5
DTA0
1
0
0
0
0
0
0
1
81h Date set to 1,
enabled
11010
-10
-305
MOA0
1
0
0
0
0
0
0
1
81h Month set to 1,
enabled
DWA0
0
0
0
0
0
0
0
0
00h Day of week
disabled
ALARM Registers (10h to 15h)
The alarm register bytes are set up identical to the RTC
register bytes, except that the MSB of each byte functions as
an enable bit (enable = “1”). These enable bits specify which
alarm registers (seconds, minutes, etc.) are used to make
the comparison. Note that there is no alarm byte for year.
The alarm function works as a comparison between the alarm
registers and the RTC registers. As the RTC advances, the
alarm will be triggered once a match occurs between the
alarm registers and the RTC registers. Any one alarm register,
multiple registers, or all registers can be enabled for a match.
There are two alarm operation modes: Single Event and
periodic Interrupt Mode:
• Single Event Mode is enabled by setting the bit 7 on any
of the Alarm registers (ESCA0... EDWA0) to “1”, the IM bit
to “0”, and disabling the frequency output. This mode
permits a one-time match between the Alarm registers
and the RTC registers. Once this match occurs, the ALM
bit is set to “1” and the IRQ/FOUT output will be pulled low
and will remain low until the ALM bit is reset. This can be
done manually or by using the auto-reset feature.
• Interrupt Mode is enabled by setting the bit 7 on any of
the Alarm registers (ESCA0... EDWA0) to “1”, the IM bit to
“1”, and disabling the frequency output. The IRQ/FOUT
19
After these registers are set, an alarm will be generated when
the RTC advances to exactly 11:30 a.m. on January 1 (after
seconds changes from 59 to 00) by setting the ALM bit in the
status register to “1” and also bringing the IRQ/FOUT output
low.
Example 2
• Pulsed interrupt once per minute (IM = ”1”)
• Interrupts at one minute intervals when the seconds
register is at 30s.
• Set Alarm registers as follows:
BIT
ALARM
REGISTER 7 6 5 4 3 2 1 0 HEX
DESCRIPTION
SCA0
1 0 1 1 0 0 0 0 B0h Seconds set to 30,
enabled
MNA0
0 0 0 0 0 0 0 0 00h Minutes disabled
HRA0
0 0 0 0 0 0 0 0 00h Hours disabled
DTA0
0 0 0 0 0 0 0 0 00h Date disabled
MOA0
0 0 0 0 0 0 0 0 00h Month disabled
DWA0
0 0 0 0 0 0 0 0 00h Day of week disabled
FN6659.2
June 23, 2009
ISL12022
DST Control Registers (DSTCR)
Once the registers are set, the following waveform will be
seen at IRQ/FOUT:
8 bytes of control registers have been assigned for the
Daylight Savings Time (DST) functions. DST beginning (set
Forward) time is controlled by the registers DstMoFd,
DstDwFd, DstDtFd, and DstHrFd. DST ending time (set
Backward or Reverse) is controlled by DstMoRv, DstDwRv,
DstDtRv and DstHrRv.
RTC AND ALARM REGISTERS ARE BOTH “30s”
60s
Tables 20 and 21 describe the structure and functions of the
DSTCR.
FIGURE 13. IRQ/FOUT WAVEFORM
DST FORWARD REGISTERS (20H TO 23H)
Note that the status register ALM bit will be set each time the
alarm is triggered, but does not need to be read or cleared.
DST forward is controlled by the following DST Registers:
Time Stamp VDD to Battery Registers (TSV2B)
DST Enable
The TSV2B Register bytes are identical to the RTC register
bytes, except they do not extend beyond the Month. The Time
Stamp captures the FIRST VDD to Battery Voltage transition
time, and will not update upon subsequent events, until cleared
(only the first event is captured before clearing). Set CLRTS = 1
to clear this register (Add 09h, PWR_VDD register).
DSTE is the DST Enabling Bit located in Bit 7 of register 20h
(DstMoFdxx). Set DSTE = 1 will enable the DSTE function.
Upon powering up for the first time (including battery), the
DSTE bit defaults to “0”. When DSTE is set to “1” the RTC
time must be at least one hour before the scheduled DST
time change for the correction to take place. When DSTE is
set to “0”, the DSTADJ bit in the Status Register
automatically resets to “0”.
Note that the time stamp registers are cleared to all “0”,
including the month and day, which is different from the RTC
and alarm registers (those registers default to 01h). This is
the indicator that no time stamping has occurred since the
last clear or initial power-up. Once a time stamp occurs,
there will be a non-zero time stamp.
DST Month Forward
DstMoFd sets the Month that DST starts. The format is the
same as for the RTC register month, from 1 to 12. The
default value for the DST begin month is 00h.
Time Stamp Battery to VDD Registers (TSB2V)
The Time Stamp Battery to VDD Register bytes are identical
to the RTC register bytes, except they do not extend beyond
Month. The Time Stamp captures the LAST transition of
VBAT to VD (only the last event of a series of power-up/down
events is retained). Set CLRTS = 1 to clear this register (Add
09h, PWR_VDD register).
TABLE 20. DST FORWARD REGISTERS
ADDRESS
FUNCTION
7
6
5
4
3
2
1
0
20h
Month Forward
DSTE
21h
Day Forward
0
0
0
MoFd20
MoFd13
MoFd12
MoFd11
MoFd10
DwFdE
WkFd12
WkFd11
WkFd10
DwFd12
DwFd11
DwFd10
22h
Date Forward
0
0
DtFd21
DtFd20
DtFd13
DtFd12
DtFd11
DtFd10
23h
Hour Forward
0
0
HrFd21
HrFd20
HrFd13
HrFd12
HrFd11
HrFd10
TABLE 21. DST REVERSE REGISTERS
ADDRESS
NAME
7
6
5
4
3
2
1
0
24h
Month Reverse
0
0
0
MoRv20
MoRv13
MoRv12
MoRv11
MoRv10
25h
Day Reverse
0
DwRvE
WkRv12
WkRv11
WkRv10
DwRv12
DwRv11
DwRv10
26h
Date Reverse
0
0
DtRv21
DtRv20
DtRv13
DtRv12
DtRv11
DtRv10
27h
Hour Reverse
0
0
HrRv21
HrRv20
HrRv13
HrRv12
HrRv11
HrRv10
20
FN6659.2
June 23, 2009
ISL12022
DST Day/Week Forward
DstDwFd contains both the Day of the Week and the Week
of the Month data for DST Forward control. DST can be
controlled either by actual date or by setting both the Week
of the month and the Day of the Week. DstDwFdE sets the
priority of the Day/Week over the Date. For DstDwFdE = 1,
Day/Week is the priority. You must have the correct Day of
Week entered in the RTC registers for the Day/Week
correction to work properly.
• Bits 0,1,2 contain the Day of the week information which
sets the Day of the Week that DST starts. Note that Day of
the week counts from 0 to 6, like the RTC registers. The
default for the DST Forward Day of the Week is 00h
(normally Sunday).
• Bits 3, 4, 5 contain the Week of the Month information that
sets the week that DST starts. The range is from 1 to 5, and
Week 7 is used to indicate the last week of the month. The
default for the DST Forward Week of the Month is 00h.
DST Date Forward
DstDtfd controls which Date DST begins. The format for the
Date is the same as for the RTC register, from 1 to 31. The
default value for DST forward date is 00h. DstDtFd is only
effective if DstDwFdE = 0.
DST Hour Forward
DstHrFd controls the hour that DST begins. The RTC hour
and DstHrFd registers have the same formats except there
is no Military bit for DST hour. The user sets the DST hour
with the same format as used for the RTC hour (AM/PM or
MIL) but without the MIL bit, and the DST will still advance as
if the MIL bit were there. The default value for DST hour
Forward is 00h.
DST REVERSE REGISTERS (24H TO 27H)
DST end (reverse) is controlled by the following DST Registers:
DST Month Reverse
DstMoRv sets the Month that DST ends. The format is the
same as for the RTC register month, from 1 to 12. The
default value for the DST end month is October (10h).
default for the DST Reverse Day of the Week is 00h
(normally Sunday).
• Bits 3, 4, 5 contain the Week of the Month information that
sets the week that DST ends. The range is from 1 to 5,
and Week 7 is used to indicate the last week of the month.
The default for the DST Reverse Week of the Month is
00h.
DST Date Reverse
DstDtRv controls which Date DST ends. The format for the
Date is the same as for the RTC register, from 1 to 31. The
default value for DST Date Reverse is 00h. The DstDtRv is
only effective if the DwRvE = 0.
DST Hour Reverse
DstHrRv controls the hour that DST ends. The RTC hour
and DstHrFd registers have the same formats except there
is no Military bit for DST hour. The user sets the DST hour
with the same format as used for the RTC hour (AM/PM or
MIL) but without the MIL bit, and the DST will still advance as
if the MIL bit were there. The default value for DST hour
Reverse is 00h.
TEMP Registers (TEMP)
The temperature sensor produces an analog voltage output
which is input to an A/D converter and produces a 10-bit
temperature value in degrees Kelvin. TK07:00 are the LSBs
of the code, and TK09:08 are the MSBs of the code. The
temperature result is actually the average of two successive
temperature measurements to produce greater resolution for
the temperature control. The output code can be converted
to degrees Centigrade (°C) by first converting from binary to
decimal, dividing by 2, and then subtracting 273d, as shown
in Equation 4:
(EQ. 4)
Temperature in °C = [(TK <9:0>)/2] - 273
The practical range for the temp sensor register output is from
446d to 726d, or -50°C to +90°C. The temperature
compensation function is only guaranteed over -40°C to +85°C.
The TSE bit must be set to “1” to enable temperature sensing.
TABLE 22.
DST Day/Week Reverse
DstDwRv contains both the Day of the Week and the Week
of the Month data for DST Reverse control. DST can be
controlled either by actual date or by setting both the Week
of the month and the Day of the Week. DstDwRvE sets the
priority of the Day/Week over the Date. For DstDwRvE = 1,
Day/Week is the priority. You must have the correct Day of
Week entered in the RTC registers for the Day/Week
correction to work properly.
• Bits 0,1,2 contain the Day of the week information which
sets the Day of the Week that DST ends. Note that Day of
the week counts from 0 to 6, like the RTC registers. The
21
TEMP
TK0L
TK0M
7
6
5
4
3
2
1
0
TK07 TK06 TK05 TK04 TK03 TK02 TK01 TK00
0
0
0
0
0
0
TK09 TK08
NPPM Registers (NPPM)
The NPPM value is exactly 2x the net correction required to
bring the oscillator to 0ppm error. The value is the combination
of oscillator Initial Correction (IPPM) and crystal temperature
dependent correction (CPPM).
IPPM is used to compensate the oscillator offset at room
temperature and is controlled by the ITR0 and BETA
registers, which are fixed during factor test.
FN6659.2
June 23, 2009
ISL12022
The CPPM compensates the oscillator frequency fluctuation
over temperature. It is determined by the temperature (T),
crystal curvature parameter (ALPHA), and crystal turnover
temperature (XT0). T is the result of the temp sensor/ADC
conversion, whose decimal result is 2x the actual
temperature in Kelvin. ALPHA is from either the ALPHA
(cold) or ALPHAH (hot) register depending on T, and XT0 is
from the XT0 register.
TABLE 24. XT0 VALUES (Continued)
NPPM is governed by Equation 5:
NPPM = IPPM(ITR0,BETA) + ALPHA x (T-T0)2
NPPM = IPPM + CPPM
2
ALPHA • ( T – T0 )
NPPM = IPPM + ---------------------------------------------------4096
(EQ. 5)
where:
ALPHA = α • 2048
T is the reading of the ADC, result is 2 x temperature in
degrees Kelvin.
T = ( 2 • 298 ) + XT0
(EQ. 6)
or T = 596 + XT0
Note that NPPM can also be predicted from the FATR and
FDTR register by the relationship (all values in decimal):
NPPM = 2*(BETA*FATR - (FDTR-16))
XT<4:0>
TURNOVER TEMPERATURE
01001
29.5
01000
29.0
00111
28.5
00110
28.0
00101
27.5
00100
27.0
00011
26.5
00010
26.0
00001
25.5
00000
25.0
10000
25.0
10001
24.5
10010
24.0
10011
23.5
10100
23.0
10101
22.5
10110
22.0
10111
21.5
11000
21.0
XT0 Registers (XT0)
11001
20.5
TURNOVER TEMPERATURE (XT<3:0>)
11010
20.0
The apex of the Alpha curve occurs at a point called the
turnover temperature, or XT0. Crystals normally have a
turnover temperature between +20°C and +30°C, with most
occurring near +25°C.
11011
19.5
11100
19.0
11101
18.5
TABLE 23. TURNOVER TEMPERATURE
11110
18.0
11111
17.5
ADDR
7
6
5
4
3
2
1
0
2Ch
0
0
0
XT4
XT3
XT2
XT1
XT0
ALPHA Hot Register (ALPHAH)
The ISL12022 allows setting the turnover temperature so
that temperature compensation can more exactly fit the
curve of a crystal. Table 24 shows the values available, with
a range from +17.5°C to +32.5°C in +0.5°C increments. The
default value is 00000b or +25°C.
TABLE 24. XT0 VALUES
XT<4:0>
TURNOVER TEMPERATURE
01111
32.5
01110
32.0
01101
31.5
01100
31
01011
30.5
01010
30
22
TABLE 25. ALPHAH REGISTER
ADDR
7
2Dh
D
6
5
4
3
2
1
0
ALP_H6 ALP_H5 ALP_H4 ALP_H3 ALP_H2 ALP_H1 ALP_H0
The Alpha Hot variable is 7 bits and is defined as the
temperature coefficient of Crystal from the T0 value to +85°C.
(both Alpha Hot and Alpha Cold must be programmed to
provide full temperature compensation). It is normally given in
units of ppm/°C2,with a typical value of -0.034. Like the Alpha
Cold version, a scaled version of the absolute value of this
coefficient is used in order to get an integer value. Therefore,
AlphaH<7:0> is defined as the (|Actual AlphaH Value| x 2048)
and converted to binary. For example, a crystal with AlphaH of
-0.034ppm/°C2 is first scaled (|2048*(-0.034)| = 70d) and then
converted to a binary number of 0100110b.
FN6659.2
June 23, 2009
ISL12022
Protocol Conventions
The practical range of Actual AlphaH values is from
-0.020 to -0.060.
The ALPHAH register should only be changed while the TSE
(Temp Sense Enable) bit is “0”.
User Registers (Accessed by Using Slave
Address 1010111x)
Addresses [00h to 7Fh]
These registers are 128 bytes of battery-backed user SRAM.
I2C Serial Interface
The ISL12022 supports a bi-directional bus oriented
protocol. The protocol defines any device that sends data
onto the bus as a transmitter and the receiving device as the
receiver. The device controlling the transfer is the master
and the device being controlled is the slave. The master
always initiates data transfers and provides the clock for
both transmit and receive operations. Therefore, the
ISL12022 operates as a slave device in all applications.
All communication over the I2C interface is conducted by
sending the MSB of each byte of data first.
Data states on the SDA line can change only during SCL
LOW periods. SDA state changes during SCL HIGH are
reserved for indicating START and STOP conditions (see
Figure 14). On power-up of the ISL12022, the SDA pin is in
the input mode.
All I2C interface operations must begin with a START
condition, which is a HIGH to LOW transition of SDA while
SCL is HIGH. The ISL12022 continuously monitors the SDA
and SCL lines for the START condition and does not
respond to any command until this condition is met (see
Figure 14). A START condition is ignored during the
power-up sequence.
All I2C interface operations must be terminated by a STOP
condition, which is a LOW to HIGH transition of SDA while
SCL is HIGH (see Figure 14). A STOP condition at the end
of a read operation or at the end of a write operation to
memory only places the device in its standby mode.
An acknowledge (ACK) is a software convention used to
indicate a successful data transfer. The transmitting device,
either master or slave, releases the SDA bus after
transmitting eight bits. During the ninth clock cycle, the
receiver pulls the SDA line LOW to acknowledge the
reception of the 8 bits of data (see Figure 15).
SCL
SDA
DATA
STABLE
START
DATA
CHANGE
DATA
STABLE
STOP
FIGURE 14. VALID DATA CHANGES, START AND STOP CONDITIONS
SCL FROM
MASTER
1
8
SDA OUTPUT FROM
TRANSMITTER
9
HIGH IMPEDANCE
HIGH IMPEDANCE
SDA OUTPUT FROM
RECEIVER
START
ACK
FIGURE 15. ACKNOWLEDGE RESPONSE FROM RECEIVER
23
FN6659.2
June 23, 2009
ISL12022
WRITE
SIGNALS FROM
THE MASTER
S
T
A
R
T
SIGNAL AT SDA
ADDRESS
BYTE
IDENTIFICATION
BYTE
1 1 0 1 1 1 1 0
SIGNALS FROM
THE ISL12022
S
T
O
P
DATA
BYTE
0 0 0 0
A
C
K
A
C
K
A
C
K
FIGURE 16. BYTE WRITE SEQUENCE (SLAVE ADDRESS FOR CSR SHOWN)
The ISL12022 responds with an ACK after recognition of a
START condition followed by a valid Identification Byte, and
once again, after successful receipt of an Address Byte. The
ISL12022 also responds with an ACK after receiving a Data
Byte of a write operation. The master must respond with an
ACK after receiving a Data Byte of a read operation.
Device Addressing
The last bit of the Slave Address Byte defines a read or write
operation to be performed. When this R/W bit is a “1”, a read
operation is selected. A “0” selects a write operation (refer to
Figure 17).
After loading the entire Slave Address Byte from the SDA bus,
the ISL12022 compares the device identifier and device select
bits with “1101111” or “1010111”. Upon a correct compare, the
device outputs an acknowledge on the SDA line.
Following the Slave Byte is a one byte word address. The word
address is either supplied by the master device or obtained
from an internal counter. On power-up, the internal address
counter is set to address 00h, so a current address read starts
at address 00h. When required, as part of a random read, the
master must supply the 1 Word Address Bytes, as shown in
Figure 20.
In a random read operation, the slave byte in the “dummy write”
portion must match the slave byte in the “read” section. For a
random read of the Control/Status Registers, the slave byte
must be “1101111x” in both places.
1
0
1
1
A Write operation requires a START condition, followed by a
valid Identification Byte, a valid Address Byte, a Data Byte,
and a STOP condition. After each of the three bytes, the
ISL12022 responds with an ACK. At this time, the I2C
interface enters a standby state.
Read Operation
Following a start condition, the master must output a Slave
Address Byte. The 7 MSBs are the device identifiers. These
bits are “1101111” for the RTC registers and “1010111” for the
User SRAM.
1
Write Operation
1
1
R/W
SLAVE
ADDRESS BYTE
A7
A6
A5
A4
A3
A2
A1
A0
WORD ADDRESS
D7
D6
D5
D4
D3
D2
D1
D0
DATA BYTE
A Read operation consists of a three byte instruction, followed
by one or more Data Bytes (see Figure 20). The master initiates
the operation issuing the following sequence: a START, the
Identification byte with the R/W bit set to “0”, an Address Byte, a
second START, and a second Identification byte with the R/W
bit set to “1”. After each of the three bytes, the ISL12022
responds with an ACK. Then the ISL12022 transmits Data
Bytes as long as the master responds with an ACK during the
SCL cycle following the eighth bit of each byte. The master
terminates the read operation (issuing a STOP condition)
following the last bit of the last Data Byte (see Figure 20).
The Data Bytes are from the memory location indicated by
an internal pointer. This pointer’s initial value is determined
by the Address Byte in the Read operation instruction, and
increments by one during transmission of each Data Byte.
After reaching the memory location 2Fh, the pointer “rolls
over” to 00h, and the device continues to output data for
each ACK received.
TABLE 26. SUGGESTED SURFACE MOUNT CRYSTALS
MANUFACTURER
PART NUMBER
Citizen
CM200S
Epson
MC-405, MC-406
Raltron
RSM-200S
SaRonix
32S12
Ecliptek
ECPSM29T-32.768K
ECS
ECX-306
Fox
FSM-327
FIGURE 17. SLAVE ADDRESS, WORD ADDRESS, AND DATA
BYTES
24
FN6659.2
June 23, 2009
ISL12022
Application Section
Battery-Backup Details
The ISL12022 has automatic switchover to battery-backup
when the VDD drops below the VBAT mode threshold. A
wide variety of backup sources can be used, including
standard and rechargeable lithium, super capacitors, or
regulated secondary sources. The serial interface is
disabled in battery-backup, while the oscillator and RTC
registers are operational. The SRAM register contents are
powered to preserve their contents as well.
The input voltage range for VBAT is 1.8V to 5.5V, but keep in
mind the temperature compensation only operates for VBAT
> 2.7V. Note that the device is not guaranteed to operate
with a VBAT < 1.8V, so the battery should be changed before
discharging to that level. It is strongly advised to monitor the
low battery indicators in the status registers and take action
to replace discharged batteries.
If a supercapacitor is used, it is possible that it may discharge to
below 1.8V during prolonged power-down. Once powered up,
the device may lose serial bus communications until both VDD
and VBAT are powered down together. To avoid that situation,
including situations where a battery may discharge deeply, the
circuit in Figure 18 can be used.
VDD = 2.7V
TO 5.5V
ISL12022
VDD
JBAT
DBAT
BAT43W
VBAT
CIN
0.1µF
CBAT
0.1µF
+ VBAT = 1.8V
TO 3.2V
lists some recommended surface mount crystals and the
parameters of each. This list is not exhaustive and other
surface mount devices can be used with the ISL12022 if their
specifications are very similar to the devices listed. The crystal
should have a required parallel load capacitance of 12.5pF and
an equivalent series resistance of less than 50k. The crystal’s
temperature range specification should match the application.
Many crystals are rated for -10°C to +60°C (especially
through-hole and tuning fork types), so an appropriate crystal
should be selected if extended temperature range is required.
Layout Considerations
The crystal input at X1 has a very high impedance, and
oscillator circuits operating at low frequencies (such as
32.768kHz) are known to pick up noise very easily if layout
precautions are not followed. Most instances of erratic clocking
or large accuracy errors can be traced to the susceptibility of
the oscillator circuit to interference from adjacent high speed
clock or data lines. Careful layout of the RTC circuit will avoid
noise pickup and insure accurate clocking.
Figure 19 shows a suggested layout for the ISL12022 device
using a surface mount crystal. Two main precautions should
be followed:
• Do not run the serial bus lines or any high speed logic lines
in the vicinity of the crystal. These logic level lines can
induce noise in the oscillator circuit, causing misclocking.
• Add a ground trace around the crystal with one end
terminated at the chip ground. This will provide termination
for emitted noise in the vicinity of the RTC device.
GND
FIGURE 18. SUGGESTED BATTERY-BACKUP CIRCUIT
The diode, DBAT will add a small drop to the battery voltage
but will protect the circuit should battery voltage drop below
1.8V. The jumper is added as a safeguard should the battery
ever need to be disconnect from the circuit.
The VDD negative slew rate should be limited to below the
data sheet spec (10V/ms) otherwise battery switchover can
be delayed, resulting in SRAM contents corruption and
oscillator operation interruption.
Some applications will require separate supplies for the RTC
VDD and the I2C pull-ups. This is not advised, as it may
compromise the operation of the I2C bus. For applications
that do require serial bus communication with the RTC VDD
powered down, the SDA pin must be pulled low during the
time the RTC VDD ramps down to 0V. Otherwise, the device
may lose serial bus communications once VDD is powered
up, and will return to normal operation ONLY once VDD and
VBAT are both powered down together.
FIGURE 19. SUGGESTED LAYOUT FOR ISL12022 AND
CRYSTAL
In addition, it is a good idea to avoid a ground plane under
the X1 and X2 pins and the crystal, as this will affect the load
capacitance and therefore the oscillator accuracy of the
circuit. If the ~IRQ/FOUT pin is used as a clock, it should be
routed away from the RTC device as well. The traces for the
VBAT and VDD pins can be treated as a ground, and should
be routed around the crystal.
Applications Information
Crystal Oscillator Frequency Compensation
Oscillator Crystal Requirements
CRYSTAL CHARACTERISTICS
The ISL12022 uses a standard 32.768kHz crystal. Either
through hole or surface mount crystals can be used. Table 26
The ISL12022 device contains a complete system for
adjusting the frequency of the crystal oscillator to
25
FN6659.2
June 23, 2009
ISL12022
compensate for temperature variation. A typical 32.768kHz
crystal used with RTC devices has a temperature versus
frequency curve, as shown in Figure 21.
0
-20
-40
PPM
-60
capacitance to change the frequency in increments of 1ppm.
The adjustment range for the ISL12022 is +32/-31ppm.
The AT can be further refined using the BETA register. the
BETA register function is to allow for changes in CM
(motional capacitance) which will affect the incremental
frequency change of the AT adjustment. A simple test
procedure uses the BETA register to bring the step size back
to 1ppm.
-80
-100
-120
-140
-160
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80
TEMPERATURE (°C)
FIGURE 21. RTC CRYSTAL TEMPERATURE DRIFT
The curve in Figure 21 follows Equation 7:
Δf = α • ( T – T 0 )
2
(EQ. 7)
Where α is the temperature constant, with a typical value of
0.034 ppm/°C.
T0 is the turnover temperature of the crystal, which is the
apex of the parabolic curve. If the two factors α and T0 are
known, it is possible to correct for crystal temperature error
to very high accuracy.
The crystal will have an initial accuracy error at room
temperature, typically specified at ±20°C. The other
important characteristic is the capacitances associated with
the crystal. The load capacitance is normally specified at
12.5pF, although it can be lower in some cases. There is
also a motional capacitance which affects the ability of the
load capacitance to pull the oscillation frequency, and it is
usually in the range of 2.2fF to 4.0fF.
RTC CLOCK CONTROL
The ISL12022 uses two mechanisms to adjust the RTC
clock and correct for the temperature error of the external
crystal.
The Analog Trimming (AT) adjusts the load capacitance
seen by the crystal. Analog switches connect the appropriate
SIGNALS
FROM THE
MASTER
S
T
A
R
T
SIGNAL AT
SDA
IDENTIFICATION
BYTE WITH
R/W = 0
The Digital Trimming (DT) uses clock pulse add/subtract
logic to change the RTC timing during temperature
compensation. The DT steps are much coarser than the AT
steps and are therefore used for large adjustments. The DT
steps are 30.5ppm, and the range is from -305ppm to
+305ppm. The Frequency Output function will show the
clock variation with DT settings, except for the 32,768Hz
setting which only shows the AT control.
ACTIVE TEMPERATURE COMPENSATION
The ISL12022 contains an intelligent logic circuit which takes
the temperature sensor digital value as the only input
variable. It then uses the register values for the crystal
variables α and T0, and combines those with calibration from
the BETA and ITR0 registers to produce “Final” values for
the AT and DT, known as FATR (Final AT Register) and
FDTR (Final DT Register). Those AT and DT values
combine to directly compensate for the temperature error
shown in Figure 21.
The temperature sensor produces a new value every 60s (or
up to 10 minutes in battery mode), which triggers the logic to
calculate a new AT/DT value set. For every temperature
calculation result, there can only be one corresponding
AT/DT correction value.
S
T IDENTIFICATION
A
BYTE WITH
R
R/W = 1
T
ADDRESS
BYTE
A
C
K
S
T
O
P
A
C
K
1 1 0 1 1 1 1 1
1 1 0 1 1 1 1 0
A
C
K
SIGNALS FROM
THE SLAVE
Normally, the crystal frequency is adjusted at room
temperature to zero out the frequency error using the IATRxx
register bits (initial Analog Trimming). In addition, the IATRxx
setting is varied up and down to record the variation in
oscillator frequency compared to the step change in IATRxx.
Once that value is known then the BETA register is used to
adjust the step size to be as close to 1ppm per IATRxx step
as possible. After that adjustment is made, then any
ISL12022 temperature compensation adjustments will use a
1ppm change for each bit change in the internal AT
adjustment.
A
C
K
A
C
K
FIRST READ
DATA BYTE
LAST READ
DATA BYTE
FIGURE 20. READ SEQUENCE (CSR SLAVE ADDRESS SHOWN)
26
FN6659.2
June 23, 2009
ISL12022
Measuring Oscillator Accuracy
The best way to analyze the ISL12022 frequency accuracy
is to set the IRQ/FOUT pin for a specific frequency, and look
at the output of that pin on a high accuracy frequency
counter (at least 7 digits accuracy). Note that the IRQ/FOUT
is a drain output and will require a pull-up resistor.
Using the 1.0Hz output frequency is the most convenient as
the ppm error is as expressed in Equation 8:
ppm error = ( F OUT – 1 ) • 1e6
(EQ. 8)
Other frequencies may be used for measurement but the
error calculation becomes more complex.
When the proper layout guidelines are observed, the
oscillator should start up in most circuits in less than 1s.
When testing RTC circuits, a common impulse is to apply a
scope probe to the circuit at the X2 pin (oscillator output) and
observe the waveform. DO NOT DO THIS! Although in some
cases you may see a usable waveform, due to the parasitics
(usually 10pF to ground) applied with the scope probe, there
will be no useful information in that waveform other than the
fact that the circuit is oscillating. The X2 output is sensitive to
capacitive impedance so the voltage levels and the
frequency will be affected by the parasitic elements in the
scope probe. Use the FOUT output and a frequency counter
for the most accurate results.
temperature for aging or board mounting. The original
recalled value can be re-written if desired after testing.
For further information on the operation of the ISL12022 and
temperature compensated RTC’s, see Intersil Application
Note AN1389, “Using Intersil’s High Accuracy Real Time
Clock Module”.
http://www.intersil.com/data/an/AN1389.pdf
Daylight Savings Time (DST) Example
DST involves setting the forward and back times and
allowing the RTC device to automatically advance the time
or set the time back. This can be done for current year, and
future years. Many regions have DST rules that use
standard months, weeks and time of the day which permit a
pre-programmed, permanent setting.
Table 27 shows the example setup for the ISL12022.
TABLE 27. DST EXAMPLE
VARIABLE
VALUE
REGISTER
VALUE
Month Forward and DST April
Enable
15h
84h
Week and Day Forward 1st Week and
and select Day/Week, not Sunday
Date
16h
48h
Date Forward
not used
17h
00h
Temperature Compensation Operation
Hour Forward
2am
18h
02h
The ISL12022 temperature compensation feature needs to
be enabled by the user. This must be done in a specific order
as follows.
Month Reverse
October
19h
10h
Week and Day Reverse Last Week and 1Ah
and select Day/Week, not Sunday
Date
78h
Date Reverse
not used
1Bh
00h
Hour Reverse
2am
1Ch
02h
1. Read register 0Dh, the BETA register. This register
contains the 5-bit BETA trimmed value which is
automatically loaded on initial power-up. Mask off the
5LSB’s of the value just read.
2. Bit 7 of the BETA register is the master enable control for
temperature sense operation. Set this to “1” to allow
continuous temperature frequency correction. Frequency
correction will then happen every 60s with VDD applied.
3. Bits 5 and 6 of the BETA register control temperature
compensation in battery-backup mode (see Table 15).
Set the values for the operation desired.
4. Write back to register 0Dh making sure not to change the
5 LSB values, and include the desired compensation
control bits.
Note that every time the BETA register is written with the
TSE bit = 1, a temperature compensation cycle is instigated
and a new correction value will be loaded into the
FATR/FDTR registers (if the temperature changed since the
last conversion).
Also note that registers 0Bh and 0Ch, the ITR0 and ALPHA
registers, should not be changed. If they must be written be
sure to write the same values that are recalled from initial
power-up. The ITR0 register may be written if the user
wishes to re-calibrate the oscillator frequency at room
27
The Enable bit (DSTE) is in the Month forward register, so
the BCD value for that register is altered with the additional
bit. The Week and Day values along with Week/Day vs Date
select bit is in the Week/Day register, so that value is also
not straight BCD. Hour and Month are normal BCD, but the
Hour doesn’t use the MIL bit since Military time PM values
are already discretely different from AM/PM time PM values.
The DST reverse setting utilizes the option to select the last
week of the month for October, which could have 4 or 5
weeks but needs to have the time change on the last
Sunday.
Note that the DSTADJ bit in the status register monitors
whether the DST forward adjustment has happened. When it
is “1”, DST forward has taken place. When it is “0”, then
either DST reverse has happened, or it has been reset either
by initial power-up or if the DSTE bit has been set to “0”.
FN6659.2
June 23, 2009
ISL12022
Small Outline Plastic Packages (SOIC)
M8.15 (JEDEC MS-012-AA ISSUE C)
N
8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
INDEX
AREA
H
0.25(0.010) M
B M
INCHES
E
SYMBOL
-B-
1
2
3
L
SEATING PLANE
-A-
A
D
h x 45°
-C-
e
A1
B
0.25(0.010) M
C
0.10(0.004)
C A M
MIN
MAX
MIN
MAX
NOTES
A
0.0532
0.0688
1.35
1.75
-
A1
0.0040
0.0098
0.10
0.25
-
B
0.013
0.020
0.33
0.51
9
C
0.0075
0.0098
0.19
0.25
-
D
0.1890
0.1968
4.80
5.00
3
E
0.1497
0.1574
3.80
4.00
4
e
α
B S
0.050 BSC
1.27 BSC
-
H
0.2284
0.2440
5.80
6.20
-
h
0.0099
0.0196
0.25
0.50
5
L
0.016
0.050
0.40
1.27
6
N
α
NOTES:
MILLIMETERS
8
0°
8
8°
0°
7
8°
1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of
Publication Number 95.
Rev. 1 6/05
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006
inch) per side.
4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per
side.
5. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater
above the seating plane, shall not exceed a maximum value of
0.61mm (0.024 inch).
10. Controlling dimension: MILLIMETER. Converted inch dimensions
are not necessarily exact.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
28
FN6659.2
June 23, 2009