EPCOS B66202 Ferrites and accessory Datasheet

Ferrites and accessories
E 13/7/4 (EF 12.6)
Core and accessories
Series/Type:
B66305, B66202, B66306, B66414
%BUB4IFFU
September 2006, May 2008
Date:
© EPCOS AG 2006, 2008. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS’ prior express consent is prohibited.
E 13/7/4 (EF 12.6)
Core
B66305
Magnetic characteristics (per set)
Σ l/A
le
Ae
Amin
Ve
3.7 _ 0.3
_ 0.4
12.6 +0.5
g
6.5 _ 0.2
To IEC 61246
For miniature transformers
Available with SMD coil former
E cores with high permeability for common-mode
chokes and broadband applications
■ Delivery mode: single units
4.5+0.3
■
■
■
■
= 2.39 mm–1
= 29.6 mm
= 12.4 mm2
= 12.2 mm2
= 367 mm3
3.7 _ 0.3
8.9+0.6
FEK0089-9
Approx. weight 2 g/set
Ungapped
Material
AL value
nH
μe
N30
1000 +30/–20%
1900
T46
3600 ±30%
6839
PV
W/set
Ordering code
B66305G0000X130
B66305F0000X146
N27
800 +30/–20%
1510
< 0.40 (200 mT, 100 kHz, 100 °C)
B66305G0000X127
N87
850 +30/–20%
1620
< 0.20 (200 mT, 100 kHz, 100 °C)
B66305G0000X187
Gapped
Material
g
mm
AL value approx.
nH
μe
Ordering code
N27
0.04 ±0.01
250
454
B66305G0040X127
The AL value in the table applies to a core set comprising one ungapped core (dimension g = 0) and
one gapped core (dimension g > 0).
Please read Cautions and warnings and
Important notes at the end of this document.
2
09/06
E 13/7/4 (EF 12.6)
Core
B66305
Calculation factors (for formulas, see “E cores: general information”)
Material
Relationship between
air gap – AL value
Calculation of saturation current
K1 (25 °C)
K2 (25 °C)
K3 (25 °C)
K4 (25 °C)
K3 (100 °C) K4 (100 °C)
N27
28.4
– 0.676
36.5
– 0.847
33.2
– 0.865
N87
28.4
– 0.676
37.5
– 0.796
32.1
– 0.873
Validity range:
K1, K2: 0.03 mm < s < 1.00 mm
K3, K4: 30 nH < AL < 260 nH
Please read Cautions and warnings and
Important notes at the end of this document.
3
09/06
E 13/7/4 (EF 12.6)
Accessories
B66202
Coil former (magnetic axis horizontal or vertical)
Material:
GFR polyterephthalate (UL 94 V-0, insulation class to IEC 60085:
F max. operating temperature 155 °C), color code black
Valox 420-SE0 ® [E45329 (M)], GE PLASTICS B V
Solderability: to IEC 60068-2-20, test Ta, method 1 (aging 3): 235 °C, 2 s
Resistance to soldering heat: to IEC 60068-2-20, test Tb, method 1B: 350 °C, 3.5 s
Winding:
see Data Book 2007, chapter “Processing notes, 2.1”
Squared pins.
Yoke
Material:
Stainless spring steel (0.2 mm)
Coil former
Ordering code
Version
Sections
AN
mm2
lN
mm
AR value
μΩ
Pins
Horizontal
1
11.6
27.2
80.6
8
B66202A1108T001
Vertical
1
11.6
27.2
80.6
6
B66202J1106T001
Yoke (ordering code per piece, 2 are required)
B66202A2010X000
Horizontal version
14.2 _ 0.2
8.7 _ 0.2
0.6±0.1
5.1_ 0.2
0.6±0.1
0.45
5.1_ 0.2
8
5
1
4
3.81
3 x 3.81 = 11.43
1+0.1
14.2
16.2 _ 0.25
3.5 _ 0.5
1.6 _ 0.1
10.4 max.
3.9+0.1
8.7 _ 0.2
3.9+0.1
Hole arrangement
View in mounting direction
10.16
FEK0449-5-E
Please read Cautions and warnings and
Important notes at the end of this document.
4
09/06
E 13/7/4 (EF 12.6)
Accessories
B66202
Vertical version
Hole arrangement
View in mounting direction
_ 0.2
13.2 +0.5
0.5 max.
Yoke
5.2 _ 0.2
3.7 _ 0.2
3.2±0.15
FEK0450-8
Please read Cautions and warnings and
Important notes at the end of this document.
5
05/08
E 13/7/4 (EF 12.6)
Accessories
B66306
SMD coil former with gullwing terminals
Material:
GFR liquid crystal polymer (UL 94 V-0, insulation class to IEC 60085:
F max. operating temperature 155 °C), color code black
Vectra C 130 [E83005 (M)], TICONA
Solderability: to IEC 60068-2-58, test Td, method 6 (Group 3): 245 °C, 3 s
Resistance to soldering heat: to IEC 60068-2-58, test Td, method 6 (Group 3): 255 °C, 10 s
permissible soldering temperature for wire-wrap connection on coil former: 400 °C, 1 s
Winding:
see Data Book 2007, chapter “Processing notes, 2.1”
AN
mm2
lN
mm
AR value
μΩ
Terminals
Ordering code
1
13.0
27
71
10
B66306C1010T001
2
10.2
27
91
10
B66306C1010T002
8,5 _ 0,1
13 _ 0,2
8,7 _ 0,2
1,6
3,9±0,1
5,1
9,1 max.
1 x 45
7,3
3,9±0,1
Sections
13 _ 0,2
19,4 _ 0,2
2,5
20,3
10,16
2,54
1,2
4 x 2,54 = 10,16
5,1
2,54
0,6±0,05
Empfehlung für das
Recommended
Leiterplattenlayout
PCB
layout
FEK0291-X
Please read Cautions and warnings and
Important notes at the end of this document.
6
09/06
E 13/7/4 (EF 12.6)
Accessories
B66414
Cover plate
■ For stamping and for improved processing on assembly machines
■ See under SMD coil former for material and resistance to soldering heat
Ordering code
B66414A7000X000
6,6±0,1
1,8±0,1
0,5 max.
Cover plate
12,8±0,1
FEK0260-3
Please read Cautions and warnings and
Important notes at the end of this document.
7
09/06
Ferrites and accessories
Cautions and warnings
Mechanical stress and mounting
Ferrite cores have to meet mechanical requirements during assembling and for a growing number
of applications. Since ferrites are ceramic materials one has to be aware of the special behavior
under mechanical load.
As valid for any ceramic material, ferrite cores are brittle and sensitive to any shock, fast changing
or tensile load. Especially high cooling rates under ultrasonic cleaning and high static or cyclic loads
can cause cracks or failure of the ferrite cores.
For detailed information see Data Book 2007, chapter “General – Definitions, 8.1”.
Effects of core combination on AL value
Stresses in the core affect not only the mechanical but also the magnetic properties. It is apparent
that the initial permeability is dependent on the stress state of the core. The higher the stresses are
in the core, the lower is the value for the initial permeability. Thus the embedding medium should
have the greatest possible elasticity.
For detailed information see Data Book 2007, chapter “General – Definitions, 8.2”.
Heating up
Ferrites can run hot during operation at higher flux densities and higher frequencies.
NiZn-materials
The magnetic properties of NiZn-materials can change irreversible in high magnetic fields.
Processing notes
– The start of the winding process should be soft. Else the flanges may be destroid.
– To strong winding forces may blast the flanges or squeeze the tube that the cores can no more
be mount.
– To long soldering time at high temperature (>300 °C) may effect coplanarity or pin arrangement.
– Not following the processing notes for soldering of the J-leg terminals may cause solderability
problems at the transformer because of pollution with Sn oxyd of the tin bath or burned insulation
of the wire. For detailed information see Data Book 2007, chapter “Processing notes, 2.2”.
– The dimensions of the hole arrangement have fixed values and should be understood as a
recommendation for drilling the printed circuit board. For dimensioning the pins, the group of
holes can only be seen under certain conditions, as they fit into the given hole arrangement. To
avoid problems when mounting the transformer, the manufacturing tolerances for positioning the
customers’ drilling process must be considered by increasing the hole diameter.
8
09/06
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with
them than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or failure
before the end of their usual service life cannot be completely ruled out in the current state
of the art, even if they are operated as specified. In customer applications requiring a very
high level of operational safety and especially in customer applications in which the malfunction
or failure of a passive electronic component could endanger human life or health (e.g. in accident
prevention or life-saving systems), it must therefore be ensured by means of suitable design of
the customer application or other action taken by the customer (e.g. installation of protective
circuitry or redundancy) that no injury or damage is sustained by third parties in the event of
malfunction or failure of a passive electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products.
Consequently, we cannot guarantee that all products named in this publication will always be
available.
The aforementioned does not apply in the case of individual agreements deviating from the
foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version
of the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, CTVS, DSSP, MiniBlue, MKK,
MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD,
SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered
or pending in Europe and in other countries. Further information will be found on the Internet at
www.epcos.com/trademarks.
9
05/08
Similar pages