ON NCP565D2TR4G 1.5 a low dropout linear regulator Datasheet

NCP565
1.5 A Low Dropout
Linear Regulator
The NCP565 low dropout linear regulator will provide 1.5 A at a
fixed output voltage or an adjustable voltage down to 0.9 V. The fast
loop response and low dropout voltage make this regulator ideal for
applications where low voltage and good load transient response are
important. Device protection includes current limit, short circuit
protection, and thermal shutdown. The NCP565 is packaged in a 5 pin
D2PAK for adjustable voltage version and a 3 pin D2PAK for fixed
voltage version.
http://onsemi.com
MARKING
DIAGRAMS
Features
•
•
•
•
•
•
•
•
•
•
Pb−Free Packages are Available
Ultra Fast Transient Response (1.0 s)
Low Ground Current (1.1 mA @ Iload = 1.5 A)
Low Dropout Voltage (0.9 V @ Iload = 1.5 A)
Low Noise (28 Vrms)
0.9 V Reference Voltage
Adjustable Output Voltage from 7.7 V down to 0.9 V
1.2 V Fixed Output Version. Other Fixed Voltages Available on
Request
Current Limit Protection (3.5 A)
Thermal Shutdown Protection (155°C)
D2PAK
CASE 936
FIXED
1
2
3
Tab = Ground
Pin 1. Vin
2. Ground
3. Vout
D2PAK
CASE 936A
ADJUSTABLE
1
5
Typical Applications
•
•
•
•
NC
P565D2Txx
AWLYWWG
NC
P565D2Txx
AWLYWWG
Tab = Ground
Pin 1. N.C.
2. Vin
3. Ground
4. Vout
5. Adj
Servers
ASIC Power Supplies
Post Regulation for Power Supplies
Constant Current Source
xx
A
WL
Y
WW
G
= R4 or 12
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 3 of this data sheet.
 Semiconductor Components Industries, LLC, 2004
July, 2004 − Rev. 8
1
Publication Order Number:
NCP565/D
NCP565
PIN DESCRIPTION
Pin No.
Adjustable Version
Pin No.
Fixed Version
Symbol
1
−
N.C.
2
1
Vin
3, Tab
2, Tab
Ground
4
3
Vout
Regulated Output Voltage
5
−
Adj
This pin is to be connected to the Rsense resistors on the output. The
linear regulator will attempt to maintain 0.9 V between this pin and
ground. Refer to Figure 1 for the equation.
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Description
−
Positive Power Supply Input Voltage
Power Supply Ground
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Input Voltage (Note 1)
Vin
9.0
V
Output Pin Voltage
Vout
−0.3 to Vin + 0.3
V
Adjust Pin Voltage
Vadj
−0.3 to Vin + 0.3
V
°C/W
Thermal Characteristics (Note 2)
Case 936A
Thermal Resistance, Junction−to−Air
Thermal Resistance, Junction−to−Case
RJA
RJC
45
5.0
Operating Junction Temperature Range
TJ
−40 to 150
°C
Storage Temperature Range
Tstg
−55 to 150
°C
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
1. This device series contains ESD protection and exceeds the following tests:
Human Body Model JESD 22−A114−B
Machine Model JESD 22−A115−A
2. The maximum package power dissipation is:
TJ(max) TA
PD RJA
Vin
C1
Voltage
Reference
Block
Vin
C1
Voltage
Reference
Block
Vref = 0.9 V
Output
Stage
Vout
5.6
pF
Vref = 0.9 V
R1
R1
C2
C2
R2
ADJ
R2
GND
R1 R2
VVout
1
ref
Vout
Output
Stage
GND
GND
Figure 1. Typical Schematic, Adjustable Output
Figure 2. Typical Schematic, Fixed Output
http://onsemi.com
2
NCP565
ELECTRICAL CHARACTERISTICS (Vin − Vout = 1.6 V, Vout = 0.9 V, TJ = 25°C, Cin = Cout = 150 F, values unless otherwise noted.)
Characteristic
Symbol
Min
Typ
Max
Unit
Reference Voltage (10 mA < Iout < 1.5 A; 2.5 V < Vin < 9.0 V; TJ = −10 to 105°C)
Vref
0.882
(−2%)
0.9
0.918
(+2%)
V
Reference Voltage (10 mA < Iout < 1.5 A; 2.5 V < Vin < 9.0 V; TJ = −40 to 125°C)
Vout
0.873
(−3%)
0.9
0.927
(+3%)
V
ADJ Pin Current
IAdj
−
30
−
nA
Line Regulation (Iout = 10 mA)
Regline
−
0.03
−
%
Load Regulation (10 mA < Iout < 1.5 A)
Regload
−
0.03
−
%
Dropout Voltage (Iout = 1.5 A) (Note 3)
Vdo
−
0.9
1.3
V
Current Limit
Ilim
1.6
3.5
−
A
Ripple Rejection (120 Hz; Iout = 1.5 A)
RR
−
85
−
dB
Ripple Rejection (1 kHz; Iout = 1.5 A)
RR
−
75
−
dB
−
150
−
°C
ADJUSTABLE OUTPUT VERSION
Thermal Shutdown
Ground Current (Iout = 1.5 A)
Iq
−
1.1
3.0
mA
Output Noise Voltage (f = 100 Hz to 100 kHz, Iout = 1.5 A)
Vn
−
28
−
Vrms
Output Voltage (10 mA < Iout < 1.5 A; 2.5 V < Vin < 9.0 V; TJ = −10 to 105°C)
Vout
1.176
(−2%)
1.2
1.224
(+2%)
%
Output Voltage (10 mA < Iout < 1.5 A; 2.5 V < Vin < 9.0 V; TJ = −40 to 125°C)
Vout
1.164
(−3%)
1.2
1.236
(+3%)
%
Line Regulation (Iout = 10 mA)
Regline
−
0.03
−
%
Load Regulation (10 mA < Iout < 1.5 A)
Regload
−
0.03
−
%
Dropout Voltage (Iout = 1.5 A) (Note 3)
Vdo
−
0.9
1.3
V
Current Limit
Ilim
1.6
3.5
−
A
Ripple Rejection (120 Hz; Iout = 1.5 A)
RR
−
85
−
dB
Ripple Rejection (1 kHz; Iout = 1.5 A)
RR
−
75
−
dB
FIXED OUTPUT VOLTAGE
−
150
−
°C
Ground Current (Iout = 1.5 A)
Iq
−
1.1
3.0
mA
Output Noise Voltage (f = 100 Hz to 100 kHz, Iout = 1.5 A)
Vn
−
28
−
Vrms
Thermal Shutdown
3. Dropout voltage is a measurement of the minimum input/output differential at full load.
ORDERING INFORMATION
Nominal Output Voltage*
Package
Shipping†
Adj
D2PAK
50 Tube
NCP565D2TR4
Adj
D2PAK
800 Tape & Reel
NCP565D2TR4G
Adj
D2PAK
(Pb−Free)
800 Tape & Reel
NCP565D2T12
Fixed
D2PAK
50 Tube
NCP565D2T12R4
Fixed
D2PAK
800 Tape & Reel
NCP565D2T12R4G
Fixed
D2PAK
(Pb−Free)
800 Tape & Reel
Device
NCP565D2T
*For other fixed output versions, please contact the factory.
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
3
NCP565
TYPICAL CHARACTERISTICS
ISC, SHORT CIRCUIT CURRENT LIMIT (A)
Vref, REFERENCE VOLTAGE (V)
0.9005
0.9000
0.8995
0.8990
0.8985
0.8980
Vin = 2.5 V
Vout = 0.9 V
Cin = Cout = 150 F
0.8975
0.8970
−50
0
−25
25
50
75
100
150
125
3.90
3.85
3.80
3.75
3.70
3.65
3.60
Vin = 2.5 V
Vout = 0.9 V
Cin = Cout = 150 F
3.55
3.50
3.45
3.40
3.35
−50
−25
TJ, JUNCTION TEMPERATURE (°C)
50
75
100
125
150
Figure 4. Short Circuit Current Limit
vs. Temperature
1.16
1.0
IGND, GROUND CURRENT (mA)
1.2
Vin − Vout, DROPOUT VOLTAGE (V)
25
TJ, JUNCTION TEMPERATURE (°C)
Figure 3. Output Voltage vs. Temperature
Iout = 1.5 A
0.8
0.6
Iout = 50 mA
0.4
Cin = Cout = 150 F
0.2
0
−50
−25
0
25
50
75
100
125
1.14
1.12
1.10
1.08
1.06
Vin = 2.5 V
Vout = 0.9 V
Iout = 1.5 V
Cin = Cout = 150 F
1.04
1.02
1.00
0.98
0.96
−50
150
0
−25
25
50
75
100
125
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 5. Dropout Voltage vs. Temperature
Figure 6. Ground Current vs. Temperature
1.28
150
100
1.26
90
RIPPLE REJECTION (dB)
IGND, GROUND CURRENT (mA)
0
1.24
1.22
1.2
1.18
1.16
1.14
80
70
60
50
40
Iout = 1.5 A
30
20
10
1.12
0
300
600
900
1200
1500
0
10
Iout, OUTPUT CURRENT (mA)
100
1000
10000
100000 1000000
F, FREQUENCY (Hz)
Figure 7. Ground Current vs. Output Current
Figure 8. Ripple Rejection vs. Frequency
http://onsemi.com
4
NCP565
OUTPUT VOLTAGE
DEVIATION (mV)
10
0
−10
Vin = 4.59 V
Vout = 0.9 V
−20
−30
−40
Iout, OUTPUT
CURRENT (A)
Iout, OUTPUT
CURRENT (A)
OUTPUT VOLTAGE
DEVIATION (mV)
TYPICAL CHARACTERISTICS
1.50
1.00
0.50
0
0
50
100
150
200
250
300
350
10
0
−10
Vin = 4.59 V
Vout = 0.9 V
−20
−30
−40
1.50
1.00
0.50
0
400
0
0.5
1.0
1.5
Figure 9. Load Transient from 10 mA to 1.5 A
Vin = 4.59 V
Vout = 0.9 V
10
0
Iout, OUTPUT
CURRENT (A)
1.50
1.00
0.50
0
−50
0
50
100
150
200
250
300
350
30
10
0
1.50
1.00
0.50
0
400
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
TIME (s)
Figure 12. Load Transient from 1.5 A to 10 mA
100
100
90
90
NOISE DENSITY (nVrms/Hz)
NOISE DENSITY (nVrms/Hz)
4.0
Vin = 4.59 V
Vout = 0.9 V
20
Figure 11. Load Transient from 1.5 A to 10 mA
80
70
60
Vin = 3.0 V
Vout = 0.9 V
Iout = 10 mA
40
3.5
40
TIME (nS)
50
3.0
50
OUTPUT VOLTAGE
DEVIATION (mV)
OUTPUT VOLTAGE
DEVIATION (mV)
Iout, OUTPUT
CURRENT (A)
40
20
2.5
Figure 10. Load Transient from 10 mA to 1.5 A
50
30
2.0
TIME (s)
TIME (nS)
30
20
10
80
70
Vin = 3.0 V
Vout = 0.9 V
Iout = 1.5 A
60
50
40
30
20
10
0
Start 1.0 kHz
0
Start 1.0 kHz
Stop 100 kHz
FREQUENCY (kHz)
Stop 100 kHz
FREQUENCY (kHz)
Figure 13. Noise Density vs. Frequency
Figure 14. Noise Density vs. Frequency
http://onsemi.com
5
NCP565
Adjustable Operation
APPLICATION INFORMATION
The typical application circuit for the adjustable output
regulators is shown in Figure 1. The adjustable device
develops and maintains the nominal 0.9 V reference voltage
between Adj and ground pins. A resistor divider network R1
and R2 causes a fixed current to flow to ground. This current
creates a voltage across R1 that adds to the 0.9 V across R2
and sets the overall output voltage.
The output voltage is set according to the formula:
The NCP565 low dropout linear regulator provides
adjustable voltages at currents up to 1.5 A. It features ultra
fast transient response and low dropout voltage. These
devices contain output current limiting, short circuit
protection and thermal shutdown protection.
Input, Output Capacitor and Stability
An input bypass capacitor is recommended to improve
transient response or if the regulator is located more than a
few inches from the power source. This will reduce the
circuit’s sensitivity to the input line impedance at high
frequencies and significantly enhance the output transient
response. Different types and different sizes of input
capacitors can be chosen dependent on the quality of power
supply. A 150F OSCON 16SA150M type from Sanyo
should be adequate for most applications. The bypass
capacitor should be mounted with shortest possible lead or
track length directly across the regulator’s input terminals.
The output capacitor is required for stability. The NCP565
remains stable with ceramic, tantalum, and aluminum−
electrolytic capacitors with a minimum value of 1.0 F as
long as the ESR remains between 50 m and 2.5. The
NCP565 is optimized for use with a 150 F OSCON
16SA150M type in parallel with a 10F OSCON 10SL10M
type from Sanyo. The 10F capacitor is used for best AC
stability while 150F capacitor is used for achieving
excellent output transient response. The output capacitors
should be placed as close as possible to the output pin of the
device. If not, the excellent load transient response of
NCP565 will be degraded.
Vout Vref R1 R2 IAdj R2
R2
The adjust pin current, Iadj, is typically 30 nA and
normally much lower than the current flowing through R1
and R2, thus it generates a small output voltage error that can
usually be ignored.
Load Transient Measurement
Large load current changes are always presented in
microprocessor applications. Therefore good load transient
performance is required for the power stage. NCP565 has
the feature of ultra fast transient response. Its load transient
responses in Figures 9 through 12 are tested on evaluation
board shown in Figure 15. On the evaluation board, it
consists of NCP565 regulator circuit with decoupling and
filter capacitors and the pulse controlled current sink to
obtain load current transitions. The load current transitions
are measured by current probe. Because the signal from
current probe has some time delay, it causes
un−synchronization between the load current transition and
output voltage response, which is shown in Figures 9
through 12.
GEN
Vout
−VCC
Vin
Pulse
V
NCP565
RL
Evaluation Board
GND
+
+
GND
Scope Voltage Probe
Figure 15. Schematic for Transient Response Measurement
http://onsemi.com
6
NCP565
PCB Layout Considerations
several capacitors in parallel. This reduces the overall ESR
and reduces the instantaneous output voltage drop under
transient load conditions. The output capacitor network
should be as close as possible to the load for the best results.
The schematic of NCP565 typical application circuit, which
this PCB layout is base on, is shown in Figure 16. The output
voltage is set to 3.3 V for this demonstration board according
to the feedback resistors in the Table 1.
Good PCB layout plays an important role in achieving
good load transient performance. Because it is very sensitive
to its PCB layout, particular care has to be taken when
tackling Printed Circuit Board (PCB) layout. The figures
below give an example of a layout where parasitic elements
are minimized. For microprocessor applications it is
customary to use an output capacitor network consisting of
2
Vin
Vin
Vout
Vout
4
NCP565
C1
150 C2
150 1
Adj
NC
5
C4
10 GND
C3
150 C3
150 3
GND
GND
R2
R1
15.8 k
42.2 k
C6
5.6 p
Figure 16. Schematic of NCP565 Typical Application Circuit
Figure 17. Top Layer
http://onsemi.com
7
NCP565
Figure 18. Bottom Layer
NCP565
ON Semiconductor
www.onsemi.com
D1
VIN
R2
C2
R1C6
VOUT
C4
C3
C1
C5
GND
GND
July, 2003
Figure 19. Silkscreen Layer
Table 1. Bill of Materials for NCP565 Adj Demonstration Board
Item
Used #
Component
Designators
Suppliers
Part Number
1
4
Radial Lead Aluminum Capacitor
150 F/16 V
C1, C2, C3, C5
Sanyo Oscon
16SA150M
2
1
Radial Lead Aluminum Capacitor
10 F/10 V
C4
Sanyo Oscon
10SL10M
3
1
SMT Chip Resistor (0805) 15.8 K 1%
R2
Vishay
CRCW08051582F
4
1
SMT Chip Resistor (0805) 42.2 K 1%
R1
Vishay
CRCW08054222F
5
1
SMT Ceramic Capacitor (0603) 5.6 pF 10%
C6
Vishay
VJ0603A5R6KXAA
6
1
NCP565 Low Dropout Linear Regulator
U1
ON Semiconductor
NCP565D2TR4
http://onsemi.com
8
NCP565
Protection Diodes
Thermal Considerations
When large external capacitors are used with a linear
regulator it is sometimes necessary to add protection diodes.
If the input voltage of the regulator gets shorted, the output
capacitor will discharge into the output of the regulator. The
discharge current depends on the value of the capacitor, the
output voltage and the rate at which Vin drops. In the
NCP565 linear regulator, the discharge path is through a
large junction and protection diodes are not usually needed.
If the regulator is used with large values of output
capacitance and the input voltage is instantaneously shorted
to ground, damage can occur. In this case, a diode connected
as shown in Figure 20 is recommended.
This series contains an internal thermal limiting circuit
that is designed to protect the regulator in the event that the
maximum junction temperature is exceeded. This feature
provides protection from a catastrophic device failure due to
accidental overheating. It is not intended to be used as a
substitute for proper heat sinking. The maximum device
power dissipation can be calculated by:
PD The devices are available in surface mount D2PAK
package. The package has an exposed metal tab that is
specifically designed to reduce the junction to air thermal
resistance, RJA, by utilizing the printed circuit board
copper as a heat dissipater. Figure 21 shows typical RJA
values that can be obtained from a square pattern using
economical single sided 2.0 ounce copper board material.
The final product thermal limits should be tested and
quantified in order to insure acceptable performance and
reliability. The actual RJA can vary considerably from the
graph shown. This will be due to any changes made in the
copper aspect ratio of the final layout, adjacent heat sources,
and air flow.
1N4002 (Optional)
Vin
Vin
Vout
Vout
CAdj
NCP565
C1
GND
Adj
TJ(max) TA
RJA
C2
R1
R2
3.5
JUNCTION-TO-AIR (° C/W)
R θ JA, THERMAL RESISTANCE
80
PD(max) for TA = +50°C
70
3.0
Free Air
Mounted
Vertically
60
Minimum
Size Pad
50
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
2.0 oz. Copper
L
2.5
2.0
L
40
1.5
RJA
1.0
30
0
5.0
10
15
20
L, LENGTH OF COPPER (mm)
25
Figure 21. 3−Pin and 5−Pin D2PAK
Thermal Resistance and Maximum Power
Dissipation vs. P.C.B Length
http://onsemi.com
9
30
PD, MAXIMUM POWER DISSIPATION (W)
Figure 20. Protection Diode for Large
Output Capacitors
NCP565
PACKAGE DIMENSIONS
D2PAK−3
D2T SUFFIX
CASE 936−03
ISSUE B
−T−
K
OPTIONAL
CHAMFER
A
E
U
S
B
F
1
2
3
V
H
M
J
D
0.010 (0.254) M T
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS
A AND K.
4. DIMENSIONS U AND V ESTABLISH A MINIMUM
MOUNTING SURFACE FOR TERMINAL 4.
5. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH OR GATE PROTRUSIONS. MOLD FLASH
AND GATE PROTRUSIONS NOT TO EXCEED
0.025 (0.635) MAXIMUM.
TERMINAL 4
L
P
N
G
DIM
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
S
U
V
R
C
SOLDERING FOOTPRINT*
8.38
0.33
1.016
0.04
10.66
0.42
5.08
0.20
3.05
0.12
17.02
0.67
SCALE 3:1
mm inches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
10
INCHES
MIN
MAX
0.386
0.403
0.356
0.368
0.170
0.180
0.026
0.036
0.045
0.055
0.051 REF
0.100 BSC
0.539
0.579
0.125 MAX
0.050 REF
0.000
0.010
0.088
0.102
0.018
0.026
0.058
0.078
5 REF
0.116 REF
0.200 MIN
0.250 MIN
MILLIMETERS
MIN
MAX
9.804 10.236
9.042
9.347
4.318
4.572
0.660
0.914
1.143
1.397
1.295 REF
2.540 BSC
13.691 14.707
3.175 MAX
1.270 REF
0.000
0.254
2.235
2.591
0.457
0.660
1.473
1.981
5 REF
2.946 REF
5.080 MIN
6.350 MIN
NCP565
PACKAGE DIMENSIONS
D2PAK−5
D2T SUFFIX
CASE 936A−02
ISSUE B
−T−
OPTIONAL
CHAMFER
A
E
U
S
K
B
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS A
AND K.
4. DIMENSIONS U AND V ESTABLISH A MINIMUM
MOUNTING SURFACE FOR TERMINAL 6.
5. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH OR GATE PROTRUSIONS. MOLD FLASH
AND GATE PROTRUSIONS NOT TO EXCEED 0.025
(0.635) MAXIMUM.
TERMINAL 6
V
H
1 2 3 4 5
M
D
0.010 (0.254)
M
T
L
G
DIM
A
B
C
D
E
G
H
K
L
M
N
P
R
S
U
V
P
N
R
C
SOLDERING FOOTPRINT*
8.38
0.33
1.702
0.067
10.66
0.42
3.05
0.12
16.02
0.63
SCALE 3:1
1.016
0.04
mm inches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
11
INCHES
MIN
MAX
0.386
0.403
0.356
0.368
0.170
0.180
0.026
0.036
0.045
0.055
0.067 BSC
0.539
0.579
0.050 REF
0.000
0.010
0.088
0.102
0.018
0.026
0.058
0.078
5 REF
0.116 REF
0.200 MIN
0.250 MIN
MILLIMETERS
MIN
MAX
9.804 10.236
9.042
9.347
4.318
4.572
0.660
0.914
1.143
1.397
1.702 BSC
13.691 14.707
1.270 REF
0.000
0.254
2.235
2.591
0.457
0.660
1.473
1.981
5 REF
2.946 REF
5.080 MIN
6.350 MIN
NCP565
The product described herein (NCP565), may be covered by one or more of the following U.S. patents: 5,920,184; 5,834,926.
There may be other patents pending.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
http://onsemi.com
12
For additional information, please contact your
local Sales Representative.
NCP565/D
Similar pages