ON MC10H350P Pecl* to ttl translator (5 vdc power supply only) Datasheet

MC10H350
PECL* to TTL Translator
(+5 Vdc Power Supply Only)
Description
The MC10H350 is a member of the 10H family of high performance
ECL logic. It consists of 4 translators with differential inputs and TTL
outputs. The 3−state outputs can be disabled by applying a HIGH TTL
logic level on the common OE input.
The MC10H350 is designed to be used primarily in systems
incorporating both ECL and TTL logic operating off a common power
supply. The separate VCC power pins are not connected internally and
thus isolate the noisy TTL VCC runs from the relatively quiet ECL
VCC runs on the printed circuit board. The differential inputs allow the
MC10H350 to be used as an inverting or noninverting translator, or a
differential line receiver. The MC10H350 can also drive CMOS with
the addition of a pullup resistor.
http://onsemi.com
MARKING DIAGRAMS*
16
MC10H350L
AWLYYWW
1
CDIP−16
L SUFFIX
CASE 620A
Features
• Propagation Delay, 3.5 ns Typical
• MECL 10K™ Compatible
• Pb−Free Packages are Available*
16
MC10H350P
AWLYYWWG
16
1
PDIP−16
P SUFFIX
CASE 648
1
10H350
ALYWG
SOEIAJ−16
CASE 966
1 20
10H350G
AWLYYWW
20 1
PLLC−20
FN SUFFIX
CASE 775
A
WL, L
YY, Y
WW, W
G
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
*For additional marking information, refer to
Application Note AND8002/D.
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
© Semiconductor Components Industries, LLC, 2006
February, 2006 − Rev. 8
1
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 4 of this data sheet.
Publication Order Number:
MC10H350/D
MC10H350
9
3
4
2
5
6
7
11
12
10
13
14
15
VCC (+5.0 VDC) = PINS 1 AND 16
GND = PIN 8
ECL VCC
1
16
TTL VCC
AOUT
2
15
COUT
AIN
3
14
CIN
AIN
4
13
CIN
BIN
5
12
DIN
BIN
6
11
DIN
BOUT
7
10
DOUT
GND
8
9
OE
Pin assignment is for Dual−in−Line Package.
Figure 2. Dip Pin Assignment
Figure 1. Logic Diagram
Table 1. MAXIMUM RATINGS
Symbol
VCC
Characteristic
Power Supply (VEE = GND)
TA
Operating Temperature Range
Tstg
Storage Temperature Range − Plastic
− Ceramic
Rating
Unit
7.0
Vdc
0 to +75
°C
−55 to +150
−55 to +165
°C
°C
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
http://onsemi.com
2
MC10H350
Table 2. ELECTRICAL CHARACTERISTICS (VCC = 5.0 V ±5%) (Note 1)
TA = 0°C to 75°C
Symbol
Characteristic
Min
Max
Unit
TTL
ECL
−
−
20
12
mA
ICC
Power Supply Current
IIH
IINH
Input Current High
Pin 9
Others
−
−
20
50
mA
IIL
IINL
Input Current Low
Pin 9
Others
−
−
−0.6
50
mA
mA
VIH
Input Voltage High
Pin 9
2.0
−
Vdc
VIL
Input Voltage Low
Pin 9
−
0.8
Vdc
VDIFF
Differential Input Voltage (Note 1)
Pins 3−6, 11−14 (1)
350
−
mV
VCM
Voltage Common Mode
Pins 3−6, 11−14
2.8
VCC
Vdc
VOH
Output Voltage High
IOH = 3.0 mA
2.7
−
Vdc
VOL
Output Voltage Low
IOL = 20 mA
−
0.5
Vdc
IOS
Short Circuit Current
VOUT = 0 V
−60
−150
mA
IOZH
Output Disable Current High
VOUT = 2.7 V
−
50
mA
IOZL
Output Disable Current Low
VOUT = 0.5 V
−
−50
mA
*Positive Emitter Coupled Logic
1. Common mode input voltage to pins 3−4, 5−6, 11−12, 13−14 must be between the values of 2.8 V and 5.0 V. This common mode input voltage
range includes the differential input swing.
2. For single−ended use, apply 3.75 V (VBB) to either input depending on output polarity required. Signal level range to other input is 3.3 V to 4.2 V.
3. Any unused gates should have the inverting inputs tied to VCC and the noninverting inputs tied to ground to prevent output glitching.
Table 3. AC PARAMETERS (CL = 50 pF) (VCC = 5.0 ± 5%) (TA = 0°C to 75°C)
TA = 0°C to 75°C
Symbol
Min
Max
Unit
Propagation Delay Data (50% to 1.5 V)
1.5
5.0
ns
tr
Rise Time (Note 4)
0.3
1.6
ns
tf
Fall Time (Note 4)
0.3
1.6
ns
tpdLZ
tpdHZ
Output Disable Time
2.0
2.0
6.0
6.0
ns
tpdZL
tpdZH
Output Enable Time
2.0
2.0
8.0
8.0
ns
tpd
Characteristic
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
4. 1.0 V to 2.0 V w/50 pF into 500 W.
http://onsemi.com
3
MC10H350
3−STATE OUTPUT LOW ENABLE AND
DISABLE TIMES
OE
1.5 V
3−STATE OUTPUT HIGH ENABLE AND
DISABLE TIMES
OE
1.5 V
TPZL
VOUT
1.5 V
TPLZ
1.5 V
TPZH
1.5 V
QVOH ≈ 3.5 V
1.5 V
VOUT
VOL
TPHZ
0.3 V
0.3 V
Figure 3. 3−State Switching Waveforms
+7.0 V
OPEN
TPZL, TPLZ, O, C,
ALL OTHER
500 W
D.U.T
.
500 W
50 PF
*INCLUDES JIG AND PROBE CAPACITANCE
Application Note: Pin 9 is an OE and the MC10H350 is disabled when OE is at VIH or higher.
Figure 4. Test Load
ORDERING INFORMATION
Package
Shipping †
MC10H350FN
PLLC−20
46 Units / Rail
MC10H350FNG
PLLC−20
(Pb−Free)
46 Units / Rail
MC10H350FNR2
PLLC−20
500 / Tape & Reel
MC10H350FNR2G
PLLC−20
(Pb−Free)
500 / Tape & Reel
MC10H350L
CDIP−16
25 Unit / Rail
MC10H350M
SOEIAJ−16
50 Unit / Rail
MC10H350MG
SOEIAJ−16
(Pb−Free)
50 Unit / Rail
MC10H350MEL
SOEIAJ−16
2000 / Tape & Reel
MC10H350MELG
SOEIAJ−16
(Pb−Free)
2000 / Tape & Reel
MC10H350P
PDIP−16
25 Unit / Rail
MC10H350PG
PDIP−16
(Pb−Free)
25 Unit / Rail
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
4
MC10H350
PACKAGE DIMENSIONS
20 LEAD PLLC
CASE 775−02
ISSUE E
0.007 (0.180) M T L−M
B
Y BRK
−N−
U
N
S
0.007 (0.180) M T L−M
S
S
N
S
D
−L−
−M−
Z
W
20
D
1
V
0.007 (0.180) M T L−M
S
N
S
R
0.007 (0.180) M T L−M
S
N
S
Z
T L−M
S
N
H
J
0.007 (0.180) M T L−M
S
−T−
VIEW S
SEATING
PLANE
F
0.007 (0.180) M T L−M
S
VIEW S
N
S
N
S
K
0.004 (0.100)
G
S
S
K1
E
G1
0.010 (0.250) S T L−M
S
VIEW D−D
A
C
0.010 (0.250)
G1
X
NOTES:
1. DIMENSIONS AND TOLERANCING PER ANSI Y14.5M,
1982.
2. DIMENSIONS IN INCHES.
3. DATUMS −L−, −M−, AND −N− DETERMINED WHERE TOP
OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD
PARTING LINE.
4. DIMENSION G1, TRUE POSITION TO BE MEASURED AT
DATUM −T−, SEATING PLANE.
5. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH.
ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE.
6. DIMENSIONS IN THE PACKAGE TOP MAY BE SMALLER
THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300).
DIMENSIONS R AND U ARE DETERMINED AT THE
OUTERMOST EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE
BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY
MISMATCH BETWEEN THE TOP AND BOTTOM OF THE
PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION
TO BE GREATER THAN 0.037 (0.940). THE DAMBAR
INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO
BE SMALLER THAN 0.025 (0.635).
http://onsemi.com
5
DIM
A
B
C
E
F
G
H
J
K
R
U
V
W
X
Y
Z
G1
K1
INCHES
MIN
MAX
0.385
0.395
0.385
0.395
0.165
0.180
0.090
0.110
0.013
0.019
0.050 BSC
0.026
0.032
0.020
−−−
0.025
−−−
0.350
0.356
0.350
0.356
0.042
0.048
0.042
0.048
0.042
0.056
−−− 0.020
2_
10 _
0.310
0.330
0.040
−−−
MILLIMETERS
MIN
MAX
9.78
10.03
9.78
10.03
4.20
4.57
2.29
2.79
0.33
0.48
1.27 BSC
0.66
0.81
0.51
−−−
0.64
−−−
8.89
9.04
8.89
9.04
1.07
1.21
1.07
1.21
1.07
1.42
−−−
0.50
2_
10 _
7.88
8.38
1.02
−−−
N
S
MC10H350
PACKAGE DIMENSIONS
SOEIAJ−16
CASE 966−01
ISSUE A
16
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS D AND E DO NOT INCLUDE MOLD
FLASH OR PROTRUSIONS AND ARE MEASURED
AT THE PARTING LINE. MOLD FLASH OR
PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006)
PER SIDE.
4. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
5. THE LEAD WIDTH DIMENSION (b) DOES NOT
INCLUDE DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08 (0.003)
TOTAL IN EXCESS OF THE LEAD WIDTH
DIMENSION AT MAXIMUM MATERIAL CONDITION.
DAMBAR CANNOT BE LOCATED ON THE LOWER
RADIUS OR THE FOOT. MINIMUM SPACE
BETWEEN PROTRUSIONS AND ADJACENT LEAD
TO BE 0.46 ( 0.018).
LE
9
Q1
E HE
1
M_
L
8
Z
DETAIL P
D
e
VIEW P
A
DIM
A
A1
b
c
D
E
e
HE
L
LE
M
Q1
Z
A1
b
0.13 (0.005)
c
0.10 (0.004)
M
CDIP−16
L SUFFIX
CERAMIC DIP PACKAGE
CASE 620A−01
ISSUE O
B
A
A
16
9
1
8
B
M
L
16X
0.25 (0.010)
E
F
C
K
T
N
SEATING
PLANE
G
16X
0.25 (0.010)
M
D
T A
http://onsemi.com
6
M
J
T B
MILLIMETERS
MIN
MAX
−−−
2.05
0.05
0.20
0.35
0.50
0.10
0.20
9.90
10.50
5.10
5.45
1.27 BSC
7.40
8.20
0.50
0.85
1.10
1.50
10 _
0_
0.70
0.90
−−−
0.78
INCHES
MIN
MAX
−−− 0.081
0.002
0.008
0.014
0.020
0.007
0.011
0.390
0.413
0.201
0.215
0.050 BSC
0.291
0.323
0.020
0.033
0.043
0.059
10 _
0_
0.028
0.035
−−− 0.031
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
4. DIMENSION F MAY NARROW TO 0.76 (0.030)
WHERE THE LEAD ENTERS THE CERAMIC
BODY.
5 THIS DRAWING REPLACES OBSOLETE
CASE OUTLINE 620−10.
DIM
A
B
C
D
E
F
G
H
K
L
M
N
INCHES
MIN
MAX
0.750
0.785
0.240
0.295
−−− 0.200
0.015
0.020
0.050 BSC
0.055
0.065
0.100 BSC
0.008
0.015
0.125
0.170
0.300 BSC
0_
15 _
0.020
0.040
MILLIMETERS
MIN
MAX
19.05
19.93
6.10
7.49
−−−
5.08
0.39
0.50
1.27 BSC
1.40
1.65
2.54 BSC
0.21
0.38
3.18
4.31
7.62 BSC
0_
15 _
0.51
1.01
MC10H350
PACKAGE DIMENSIONS
PDIP−16
P SUFFIX
PLASTIC DIP PACKAGE
CASE 648−08
ISSUE R
−A−
16
9
1
8
B
F
C
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
L
S
−T−
H
SEATING
PLANE
K
G
D
M
J
16 PL
0.25 (0.010)
M
T A
M
DIM
A
B
C
D
F
G
H
J
K
L
M
S
INCHES
MIN
MAX
0.740
0.770
0.250
0.270
0.145
0.175
0.015
0.021
0.040
0.70
0.100 BSC
0.050 BSC
0.008
0.015
0.110
0.130
0.295
0.305
0_
10 _
0.020
0.040
MILLIMETERS
MIN
MAX
18.80
19.55
6.35
6.85
3.69
4.44
0.39
0.53
1.02
1.77
2.54 BSC
1.27 BSC
0.21
0.38
2.80
3.30
7.50
7.74
0_
10 _
0.51
1.01
MECL 10K is a trademark of Motorola, Inc.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
Literature Distribution Center for ON Semiconductor
USA/Canada
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Phone: 81−3−5773−3850
Email: [email protected]
http://onsemi.com
7
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
For additional information, please contact your
local Sales Representative.
MC10H350/D
Similar pages