Marktech LO566EBL3-70H-A3-MT 5-mm oval led Datasheet

Cree® 5-mm Oval LED
Model # LO566EBL3-70H-A3-MT
Data Sheet
70-degree, 5-mm oval LED lamp in blue color with tinted, transparent lens and no stopper
Applications
•
•
Variable-Message Signs
Message Boards
Absolute Maximum Ratings (TA = 25°C)
Items
Symbol
Absolute Maximum Rating
Unit
IF
25
mA
IFP
100
mA
Reverse Voltage
VR
5
V
Power Dissipation
PD
100
mW
Operation Temperature
Topr
-40 ~ +95
°C
Storage Temperature
Tstg
-40 ~ +100
°C
Lead Soldering Temperature
Tsol
Forward Current
Peak Forward Current
Note
Max. 260°C for 3 sec. max.
(3 mm from the base of the epoxy bulb)
Note: Pulse width ≤0.1 msec, duty ≤1/10.
Typical Electrical & Optical Characteristics (TA = 25°C)
Characteristics
Symbol
Condition
Unit
Forward Voltage
VF
IF = 20 mA
V
Reverse Current
IR
VR = 5 V
μA
Dominant Wavelength
λD
IF = 20 mA
nm
465
470
Luminous Intensity
IV
IF = 20 mA
mcd
550
1450
2θ½H-H
IF = 20 mA
deg
70
2θ½V-V
IF = 20 mA
deg
35
D-CT533.001
Data Sheet: CL
50% Power Angle
Minimum
Subject to change without notice.
www.cree.com/ledlamps
Typical
Maximum
3.4
4.0
100
475
1
Standard Bins for LO566EBL3-70H-A3-MT (IF = 20 mA)
Lamps are sorted to luminous intensity (IV) and dominant wavelength (λD) bins shown.
Orders for LO566EBL3-70H-A3-MT may be filled with any or all bins contained as below. All luminous intensity (IV) and dominant wavelength (λD) values shown and specified are at IF = 20 mA.
X4
X5
Luminous Intensity (IV)
V or
above
2130 mcd
U
1520 mcd
T
1100 mcd
S
770 mcd
R
550 mcd
465 nm
475 nm
470 nm
Dominant Wavelength (λD)
Forward Voltage (VF)
Rank
V7
V8
V9
V10
V11
V12
Voltage
2.8-3.0V
3.0-3.2V
3.2-3.4V
3.4-3.6V
3.6-3.8V
3.8-4.0V
*Majority VF bins are highlighted in Yellow
Important Notes:
1. All ranks will be included per delivery; rank ratio will be based on the dice distribution.
2. Pb content <1000 ppm.
3. Tolerance of measurement of luminous intensity is ±15%.
4. Tolerance of measurement of dominant wavelength is ±1 nm.
5. Tolerance of measurement of VF is ±0.05 V.
6. Packaging methods are available for selection; please refer to the “Cree LED Lamp Packaging Standard” document.
7. Please refer to the “Cree LED Lamp Reliability Test Standards” document for reliability test conditions.
8. Please refer to the “Cree LED Lamp Soldering & Handling” document for information about how to use this LED
product safely.
Copyright © 2008 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the
Cree logo are registered trademarks of Cree, Inc.
2
CLD-CT533.001
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
www.cree.com/ledlamps
Graphs

















































  
 


































  




 








1. Cathode PAD Area (0.18 x 0.18inch2)
2. Height above nominal seating plane in inches(0.3inch)
Copyright © 2008 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the
Cree logo are registered trademarks of Cree, Inc.
3

CLD-CT533.001
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
www.cree.com/ledlamps
Mechanical Dimensions
All dimensions are in mm. Tolerance is ±0.25 mm unless otherwise noted.

An epoxy meniscus may extend about 1.5 mm
down the leads.



Burr around bottom of epoxy may be 0.5 mm max.






















 







 

  


Notes
RoHS Compliance












The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or
otherwise restricted materials in this product are below the maximum concentration values (also referred to as the
threshold
limits)
permitted for such
or are used in 
an exempted application,
in accordance with EU Direc

 substances,

tive 2002/95/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(RoHS), as amended through April 21, 2006.
Vision Advisory Claim
 





 





Users should be cautioned not to stare at the light of this LED product. The bright light can damage the eye.
Copyright © 2008 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the
are registered
trademarks of Cree, Inc.


Cree logo

4
 









CLD-CT533.001
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
www.cree.com/ledlamps
Similar pages