MC10EP29, MC100EP29 3.3V / 5VECL Dual Differential Data and Clock D Flip−Flop With Set and Reset http://onsemi.com Description The MC10/100EP29 is a dual master−slave flip−flop. The device features fully differential Data and Clock inputs as well as outputs. The MC10/100EP29 is functionally equivalent to the MC10/100EL29. Data enters the master latch when the clock is LOW and transfers to the slave upon a positive transition on the clock input. The differential inputs have special circuitry which ensures device stability under open input conditions. When both differential inputs are left open the D input will pull down to VEE and the D input will bias around VCC/2. The outputs will go to a defined state, however the state will be random based on how the flip flop powers up. Both flip flops feature asynchronous, overriding Set and Reset inputs. Note that the Set and Reset inputs cannot both be HIGH simultaneously. The VBB pin, an internally generated voltage supply, is available to this device only. For single-ended input conditions, the unused differential input is connected to VBB as a switching reference voltage. VBB may also rebias AC coupled inputs. When used, decouple VBB and VCC via a 0.01 mF capacitor and limit current sourcing or sinking to 0.5 mA. When not used, VBB should be left open. The 100 Series contains temperature compensation. Features • Maximum Frequency > 3 GHz Typical • 500 ps Typical Propagation Delays • PECL Mode Operating Range: VCC = 3.0 V to 5.5 V TSSOP−20 DT SUFFIX CASE 948E 20 1 QFN−20 MN SUFFIX CASE 485E xxx A L Y W G XXXX EP29 ALYWG G = MC10 or 100 = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package (Note: Microdot may be in either location) with VEE = 0 V with VEE = −3.0 V to −5.5 V ORDERING INFORMATION • Open Input Default State • Safety Clamp on Inputs • These are Pb−Free Devices December, 2006 − Rev. 4 XXXX EP29 ALYWG G *For additional marking information, refer to Application Note AND8002/D. • NECL Mode Operating Range: VCC = 0 V © Semiconductor Components Industries, LLC, 2006 MARKING DIAGRAM* See detailed ordering and shipping information in the package dimensions section on page 8 of this data sheet. 1 Publication Order Number: MC10EP29/D MC10EP29, MC100EP29 VCC R0 S0 Q0 Q0 Q1 Q1 S1 R1 VEE 20 19 18 17 16 15 14 13 12 11 Q S R S Q Q D R Q CLK CLK 1 2 3 4 5 D0 D0 VBB CLK0 CLK0 7 8 9 CLK1 D1 D1 6 CLK1 D 10 VCC Warning: All VCC and VEE pins must be externally connected to Power Supply to guarantee proper operation. Figure 1. 20−Lead Pinout (Top View) and Logic Diagram Exposed Pad D0 D0 VCC R0 S0 20 19 18 17 16 VBB 1 15 Q0 CLK0 2 14 Q0 CLK0 3 CLK1 4 12 Q1 CLK1 5 11 S1 MC10/100EP17 6 NOTE: 7 8 13 9 Q1 10 D1 D1 VCC VEE R1 The Exposed Pad (EP) on package bottom must be attached to a heat−sinking conduit. The Exposed Pad may only be electrically connected to VEE. Figure 1. QFN−20 Pinout (Top View) Table 1. PIN DESCRIPTION Pin Function D0*, D0*; D1*, D1* ECL Differential Data Inputs R0*, R1* ECL Reset Inputs CLK0*, CLK0* ECL Differential Clock Inputs CLK1*, CLK1* ECL Differential Clock Inputs S0* S1* ECL Set Inputs Q0, Q0; Q1, Q1 ECL Differential Data Outputs VBB Reference Voltage Output VCC Positive Supply VEE Negative Supply EP Exposed Pad Table 2. TRUTH TABLE R S D CLK Q Q L L L Z L H L L H Z H L H L X X L H L H X X H L H H X X Undef Undef Z = LOW to HIGH Transition X = Don’t Care *Pins will default LOW when left open. http://onsemi.com 2 MC10EP29, MC100EP29 Table 3. ATTRIBUTES Characteristics Value Internal Input Pulldown Resistor 75 kW Internal Input Pullup Resistor N/A ESD Protection Human Body Model Machine Model Charged Device Model > 2 kV > 100 V > 2 kV Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1) TSSOP−20 QFN−20 Flammability Rating Oxygen Index: 28 to 34 Pb Pkg Pb−Free Pkg Level 1 N/A Level 3 Level 1 UL 94 V−0 @ 0.125 in Transistor Count 383 Devices Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 1. For additional information, see Application Note AND8003/D. Table 4. MAXIMUM RATINGS Symbol Rating Unit VCC PECL Mode Power Supply Parameter VEE = 0 V Condition 1 6 V VEE NECL Mode Power Supply VCC = 0 V −6 V VI PECL Mode Input Voltage NECL Mode Input Voltage VEE = 0 V VCC = 0 V 6 −6 V V Iout Output Current Continuous Surge 50 100 mA mA IBB VBB Sink/Source ± 0.5 mA TA Operating Temperature Range −40 to +85 °C Tstg Storage Temperature Range −65 to +150 °C qJA Thermal Resistance (Junction−to−Ambient) 0 lfpm 500 lfpm 20 TSSOP 20 TSSOP 140 100 °C/W °C/W qJC Thermal Resistance (Junction−to−Case) Standard Board 20 TSSOP 23 to 41 °C/W qJA Thermal Resistance (Junction−to−Ambient) 0 lfpm 500 lfpm QFN−20 QFN−20 47 33 °C/W °C/W qJC Thermal Resistance (Junction−to−Case) Standard Board QFN−20 18 °C/W Tsol Wave Solder 265 265 °C Pb Pb−Free Condition 2 VI v VCC VI w VEE Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. http://onsemi.com 3 MC10EP29, MC100EP29 Table 5. 10EP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 2) −40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 35 46 55 37 57 48 40 49 60 mA Output HIGH Voltage (Note 3) 2165 2290 2415 2230 2480 2355 2290 2415 2540 mV Output LOW Voltage (Note 3) 1365 1490 1615 1430 1680 1555 1490 1615 1740 mV VIH Input HIGH Voltage (Single−Ended) 2090 2415 2155 2480 2215 2540 mV VIL Input LOW Voltage (Single−Ended) 1365 1690 1460 1755 1490 1815 mV VBB Output Voltage Reference 1790 1990 1855 2055 2115 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 4) 3.3 2.0 3.3 3.3 V IIH Input HIGH Current 150 mA IIL Input LOW Current IEE Power Supply Current VOH VOL 1890 2.0 150 0.5 1955 1915 2015 2.0 150 0.5 0.5 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 2. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to −2.2 V. 3. All loading with 50 W to VCC − 2.0 V. 4. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Table 6. 10EP DC CHARACTERISTICS, PECL VCC = 5.0 V, VEE = 0 V (Note 5) −40°C Symbol Characteristic Min Typ 25°C Max Min Typ 85°C Max Min Typ IEE Power Supply Current VOH Output HIGH Voltage (Note 3) IEE Power Supply Current 35 46 55 37 48 57 40 VOH Output HIGH Voltage (Note 6) 3865 3990 4115 3930 4055 4180 3990 VOL Output LOW Voltage (Note 6) 3065 3190 3315 3130 3255 3380 3190 3315 VIH Input HIGH Voltage (Single−Ended) 3790 4115 3855 4180 3915 VIL Input LOW Voltage (Single−Ended) 3065 3390 3130 3455 3190 VBB Output Voltage Reference 3490 3690 3555 3755 3615 VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 7) 5.0 2.0 5.0 2.0 IIH Input HIGH Current IIL Input LOW Current Max Unit 35 46 55 37 57 48 40 49 60 mA 2165 2290 2415 2230 2480 2355 2290 2415 2540 mV 49 60 mA 4115 4240 mV 3440 mV 4240 mV 3515 mV 3815 mV 5.0 V 150 mA 3590 2.0 150 0.5 3655 150 0.5 0.5 3715 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 5. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to −0.5 V. 6. All loading with 50 W to VCC − 2.0 V. 7. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. http://onsemi.com 4 MC10EP29, MC100EP29 Table 7. 10EP DC CHARACTERISTICS, NECL VCC = 0 V; VEE = −5.5 V to −3.0 V (Note 8) −40°C Symbol Characteristic Min 25°C Typ Max Min Typ 85°C Max Min Typ Max Unit IEE Power Supply Current 35 46 55 37 48 57 40 49 60 mA VOH Output HIGH Voltage (Note 9) −1135 −1010 −885 −1070 −945 −820 −1010 −885 −760 mV VOL Output LOW Voltage (Note 9) −1935 −1810 −1685 −1870 −1745 −1620 −1810 −1685 −1560 mV VIH Input HIGH Voltage (Single−Ended) −1210 −885 −1145 −820 −1085 −760 mV VIL Input LOW Voltage (Single−Ended) −1935 −1610 −1870 −1545 −1810 −1485 mV VBB Output Voltage Reference −1510 −1310 −1445 −1245 −1385 −1185 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 10) 0.0 V IIH Input HIGH Current 150 mA IIL Input LOW Current −1410 VEE + 2.0 0.0 −1345 VEE + 2.0 150 0.5 0.0 −1285 VEE + 2.0 150 0.5 0.5 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 8. Input and output parameters vary 1:1 with VCC. 9. All loading with 50 W to VCC − 2.0 V. 10. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Table 8. 100EP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 11) −40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 35 46 55 37 48 57 40 49 60 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 12) 2155 2280 2405 2155 2280 2405 2155 2280 2405 mV VOL Output LOW Voltage (Note 12) 1355 1480 1605 1355 1480 1605 1355 1480 1605 mV VIH Input HIGH Voltage (Single−Ended) 2075 2420 2075 2420 2075 2420 mV VIL Input LOW Voltage (Single−Ended) 1355 1675 1355 1675 1355 1675 mV VBB Output Voltage Reference 1775 1975 1775 1975 1775 1975 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 13) 3.3 2.0 3.3 2.0 3.3 V IIH Input HIGH Current 150 mA IIL Input LOW Current 1875 2.0 150 0.5 1875 150 0.5 0.5 1875 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 11. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to −2.2 V. 12. All loading with 50 W to VCC − 2.0 V. 13. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. http://onsemi.com 5 MC10EP29, MC100EP29 Table 9. 100EP DC CHARACTERISTICS, PECL VCC = 5.0 V, VEE = 0 V (Note 14) −40°C 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 35 46 55 37 48 57 40 49 60 mA Output HIGH Voltage (Note 15) 3855 3980 4105 3855 3980 4105 3855 3980 4105 mV Output LOW Voltage (Note 15) 3055 3180 3305 3055 3180 3305 3055 3180 3305 mV VIH Input HIGH Voltage (Single−Ended) 3775 4120 3775 4120 3775 4120 mV VIL Input LOW Voltage (Single−Ended) 3055 3375 3055 3375 3055 3375 mV VBB Output Voltage Reference 3475 3675 3475 3675 3475 3675 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 16) 5.0 2.0 5.0 2.0 5.0 V IIH Input HIGH Current 150 mA IIL Input LOW Current Symbol Characteristic IEE Power Supply Current VOH VOL 3575 2.0 3575 150 0.5 3575 150 0.5 0.5 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 14. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to −0.5 V. 15. All loading with 50 W to VCC − 2.0 V. 16. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Table 10. 100EP DC CHARACTERISTICS, NECL VCC = 0 V; VEE = −5.5 V to −3.0 V (Note 17) −40°C Symbol Characteristic Min Typ 25°C Max Min Typ 85°C Max Min Typ Max Unit IEE Power Supply Current 35 46 55 37 48 57 40 49 60 mA VOH Output HIGH Voltage (Note 18) −1145 −1020 −895 −1145 −1020 −895 −1145 −1020 −895 mV VOL Output LOW Voltage (Note 18) −1945 −1820 −1695 −1945 −1820 −1695 −1945 −1820 −1695 mV VIH Input HIGH Voltage (Single−Ended) −1225 −880 −1225 −880 −1225 −880 mV VIL Input LOW Voltage (Single−Ended) −1945 −1625 −1945 −1625 −1945 −1625 mV VBB Output Voltage Reference −1525 −1325 −1525 −1325 −1525 −1325 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 19) 0.0 V IIH Input HIGH Current 150 mA IIL Input LOW Current −1425 VEE + 2.0 0.0 150 0.5 −1425 VEE + 2.0 0.0 150 0.5 −1425 VEE + 2.0 0.5 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 17. Input and output parameters vary 1:1 with VCC. 18. All loading with 50 W to VCC − 2.0 V. 19. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. http://onsemi.com 6 MC10EP29, MC100EP29 Table 11. AC CHARACTERISTICS VCC = 0 V; VEE = −3.0 V to −5.5 V or VCC = 3.0 V to 5.5 V; VEE = 0 V (Note 20) −40°C Min Characteristic Symbol fmax Maximum Frequency (See Figure 2 Fmax/JITTER) tPLH, tPHL Propagation Delay to Output Differential S R tS tH Typ 25°C Max Min > 3.0 CLK 300 275 300 380 380 400 Setup Time Hold Time 100 100 tRR/tRR2 Set/Reset Recovery tPW Minimum Pulse Width Set, Reset tJITTER Cycle−to−Cycle Jitter (See Figure 2 Fmax/JITTER) VPP Input Voltage Swing (Note 21) tr tf Output Rise/Fall Times (20% − 80%) Q, Q Typ 85°C Max Min > 3.0 450 475 500 350 300 325 420 400 420 20 20 100 100 150 80 500 300 .2 <1 150 800 1200 100 180 250 Typ Max > 3.0 500 500 525 Unit GHz 400 350 375 470 450 470 20 20 100 100 20 20 ps 150 80 150 80 ps 500 300 500 300 .2 <1 150 800 1200 150 210 300 550 550 575 ps ps .2 <1 ps 150 800 1200 mV 175 230 325 ps 900 9 800 8 700 7 600 6 500 5 400 4 300 3 200 2 ÉÉÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉÉ (JITTER) 100 0 0 1000 2000 3000 FREQUENCY (MHz) Figure 2. Fmax/Jitter http://onsemi.com 7 1 4000 5000 JITTER OUT ps (RMS) VOUTpp (mV) NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 20. Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 W to VCC−2.0 V. 21. VPP(min) is the minimum input swing for which AC parameters are guaranteed. ÉÉ ÉÉ MC10EP29, MC100EP29 Q Zo = 50 W D Receiver Device Driver Device Q D Zo = 50 W 50 W 50 W VTT VTT = VCC − 2.0 V Figure 3. Typical Termination for Output Driver and Device Evaluation (See Application Note AND8020/D − Termination of ECL Logic Devices.) ORDERING INFORMATION Package Shipping † MC10EP29DT TSSOP−20 75 Units / Rail MC10EP29DTG TSSOP−20 (Pb−Free) 75 Units / Rail MC10EP29DTR2 TSSOP−20 2500 / Tape & Reel MC10EP29DTR2G TSSOP−20 (Pb−Free) 2500 / Tape & Reel MC10EP29MNG QFN−20 (Pb−Free) 92 Units / Rail MC10EP29MNTXG QFN−20 (Pb−Free) 3000 / Tape & Reel MC100EP29DT TSSOP−20 75 Units / Rail MC100EP29DTG TSSOP−20 (Pb−Free) 75 Units / Rail MC100EP29DTR2 TSSOP−20 2500 / Tape & Reel MC100EP29DTR2G TSSOP−20 (Pb−Free) 2500 / Tape & Reel MC100EP29MNG QFN−20 (Pb−Free) 92 Units / Rail MC100EP29MNTXG QFN−20 (Pb−Free) 3000 / Tape & Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Resource Reference of Application Notes AN1405/D − ECL Clock Distribution Techniques AN1406/D − Designing with PECL (ECL at +5.0 V) AN1503/D − ECLinPSt I/O SPiCE Modeling Kit AN1504/D − Metastability and the ECLinPS Family AN1568/D − Interfacing Between LVDS and ECL AN1672/D − The ECL Translator Guide AND8001/D − Odd Number Counters Design AND8002/D − Marking and Date Codes AND8090/D − AC Characteristics of ECL Devices http://onsemi.com 8 MC10EP29, MC100EP29 Resource Reference of Application Notes AND8020/D − Termination of ECL Logic Devices AND8066/D − Interfacing with ECLinPS AND8090/D − AC Characteristics of ECL Devices http://onsemi.com 9 MC10EP29, MC100EP29 PACKAGE DIMENSIONS TSSOP−20 CASE 948E−02 ISSUE C 20X 0.15 (0.006) T U 2X L K REF 0.10 (0.004) S L/2 20 M T U S V K K1 ÍÍÍÍ ÍÍÍÍ ÍÍÍÍ S J J1 11 B −U− PIN 1 IDENT SECTION N−N 0.25 (0.010) N 1 10 M 0.15 (0.006) T U S A −V− NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE −W−. N F DETAIL E −W− C G D H DETAIL E 0.100 (0.004) −T− SEATING DIM A B C D F G H J J1 K K1 L M PLANE SOLDERING FOOTPRINT* 7.06 1 0.65 PITCH 16X 0.36 16X 1.26 DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 10 MILLIMETERS MIN MAX 6.40 6.60 4.30 4.50 −−− 1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.27 0.37 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.252 0.260 0.169 0.177 −−− 0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.011 0.015 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ MC10EP29, MC100EP29 PACKAGE DIMENSIONS QFN−20 CASE 485E−01 ISSUE O NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION D APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 MM FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. −X− A M −Y− N B 0.25 (0.010) T 0.25 (0.010) T R J C 0.08 (0.003) T −T− K SEATING PLANE E H DIM A B C D E F G H J K L M N P R MILLIMETERS MIN MAX 4.00 BSC 4.00 BSC 0.80 1.00 0.23 0.35 2.75 2.85 2.75 2.85 0.50 BSC 1.38 1.43 0.20 REF 0.00 0.05 0.35 0.45 2.00 BSC 2.00 BSC 1.38 1.43 0.60 0.80 INCHES MIN MAX 0.157 BSC 0.157 BSC 0.031 0.039 0.009 0.014 0.108 0.112 0.108 0.112 0.020 BSC 0.054 0.056 0.008 REF 0.000 0.002 0.014 0.018 0.079 BSC 0.079 BSC 0.054 0.056 0.024 0.031 G L 6 10 5 11 1 15 F 20 D 16 NOTE 3 0.10 (0.004) M P T X Y ECLinPS is a trademark of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 11 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC10EP29/D