Source C-13-155-T-SSC3-55 155 mbps single mode transceiver Datasheet

155 Mbps Single Mode Transceiver
C-13-155-T-Sxx3(-55)-G5
Features
• Duplex SC\ST\FC Single Mode Transceiver
• Industry Standard 1x9 Footprint
• Intermediate reach SONET OC-3 SDH STM-1 Compliant
• Single +5V Power Supply
• PECL/LVPECL Differential Inputs and Outputs
• PECL/LVPECL Signal Detection Output
• Wave Solderable and Aqueous Washable
• LED Multisourced 1x9 Transceiver Interchangeable
• Class 1 Laser Int. Safety Standard IEC 825 compliant
• Uncooled laser diode with MQW structure
• Complies with Telcordia (Bellcore) GR-468-CORE
• ATM 155 Mbps links
• RoHS compliant
Absolute Maximum Rating
Symbol
Min.
Max.
Unit
Power Supply Voltage
Parameter
Vcc
0
6
V
Output Current
Iout
-
30
mA
-
-
260
ºC
Tstg
-40
85
ºC
Symbol
Min.
Typ.
Max.
Unit
Vcc
4.75
5
5.25
V
Topr
-
0
70
ºC
-
155
-
Soldering Temperature
Storage Temperature
Note
10 seconds on leads only
Recommended Operating Condition
Parameter
Power Supply Voltage1
Operating Temperature1 (Case)
Data Rate
Mbps
Note 1 : Please refer to ordering information
Transmitter Specifications
Parameter
Symbol
Min
Typical
Max
Unit
Notes
Po
-15
-
-8
dBm
Output power is coupled into a 9/125 µm
single mode fiber
λ
1261
1310
1360
nm
7.7
nm
-
dB
Optical
Optical Transmit Power
Output center Wavelength
Output Spectrum Width
∆λ
Extinction Ratio
ER
8.2
-
Output ulse Mask
Compliant with FDDI SMF-PMD1
Output Eye
Compliant with ITU-T recommendation G.957
Optical Rise Time
Optical Fall Time
Relative Intensity Noise
Total Jitter
LUMINENTOIC.COM
tr
-
-
2
RMS(σ)
ns
10% to 90% Values
10% to 90% Values
tf
-
-
2
ns
RIN
-
-
-116
dB/Hz
TJ
-
-
1.2
ns
Measured with 223-1 PRBS with 72 ones and
72 zeros.
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
1
LUMNDS1930-Aug0508
Rev A.0
155 Mbps Single Mode Transceiver
C-13-155-T-Sxx3(-55)-G5
Transmitter Specifications
Parameter
Symbol
Min
Typical
Max
Unit
ICC
-
-
160
mA
Notes
Electrical
Power Supply Current
Maximum current is specified at
Vcc= Maximum @ maximum temperature
Data Input Current-Low
IIL
-350
-
-
µA
Data Input Current-High
IIH
-
-
350
µA
Differential Input Voltage
VIH-VIL
300
-
-
mV
Data Input Voltage-Low
VIL-VCC
-2.0
-
-1.58
V
Data Input Voltage-High
VIH-VCC
-1.1
-
-0.74
V
These inputs are compatible with 10K, 10KH
and 100K ECL and PECL inputs
Symbol
Min
Typical
Max
Unit
Notes
-
-
-
-34
dBm
Maximum Input Power
Pin
-7
-
-
dBm
Signal Detect-Asserted
Pa
-
-
-34
dBm
Measured on transition: low to high
Signal Detect-Deasserted
Pd
-47
-
-
dBm
Measured on transition: high to low
1.0
-
4.0
dB
1100
-
1600
nm
Symbol
Min
Typical
Max
Unit
Notes
ICC
-
-
100
mA
The current excludes the output load current
Data Input Voltage-Low
VOL -Vcc
-2
-
-1.58
V
Receiver Specifications
Parameter
Optical
Sensitivity
Signal Detect-Hysteresis
Wavelength of Operation
Measured with 223-1 PRBS with 72 ones and
72 zeros.
Receiver Specifications
Parameter
Electrical
Power Supply Current
Data Input Voltage-High
VOH- Vcc
-1.1
-
-0.74
V
Signal Detect Output Voltage-Low
VSDL-Vcc
-2
-
-1.58
V
Signal Detect Output Voltage-High
VSDH- Vcc
-1.1
-
-0.74
V
LUMINENTOIC.COM
These outputs are compatible with 10K,
10KH and 100KECL and PECL outputs.
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
2
LUMNDS1930-Aug0508
Rev A.0
155 Mbps Single Mode Transceiver
C-13-155-T-Sxx3(-55)-G5
Connection Diagram
1. (Rx GND)
2. (RD +)
3. (RD-)
4. (SD)
5. (Rx Vcc)
6. (Tx Vcc)
7. (TD-)
8. (TD+)
9. (Tx GND)
NC
Top View
NC
Receiver Signal Ground
Receiver Data Out
Receiver Data Out Bar
Signal Detect
Receiver Power Supply
Transmitter Power Supply
Transmitter Data In Bar
Transmitter Data in
Transmitter Signal Ground
PIN
Symbol
1
RxGND
2
RD+
See recommended circuit schematic
3
RD-
See recommended circuit schematic
4
SD
Active high on this indicates a received optical signal
5
RxVcc
6
TxVcc
7
TD-
See recommended circuit schematic
TD+
See recommended circuit schematic
8
Warnings
9
Notes
Directly connect this pin to the receiver ground plane
+5V dc power for the receiver section
+5V dc power for the transmitter section
TxGND
Directly connect this pin to the transmitter ground plane
Legal Notice
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
3
LUMNDS1930-Aug0508
Rev A.0
155 Mbps Single Mode Transceiver
C-13-155-T-Sxx3(-55)-G5
Recommended Circuit Schematic
C-13-155-T-Sxx3(-55)-G5
Tx Vcc
C5
Rx Vcc
9
R1
8
7
6
5
4 3
2
1
R3
R9
R5
C6
R7
TD +
RD +
TD -
RD -
Tx Vcc
SD
Rx Vcc
R2
R4
No internal
connection
Transceiver
Top view
No internal
connection
R10
R6
R8
L1
Notes +5V:
R1=R3=R5=R7=R9=82�
R2=R4=R6=R8=R10=130�
C1=C2=C3=C5=C6=0.1�F
C4=10�F
L1=L2=1�H
Vcc
C3
Rx Vcc
C1
L2
C4
Tx Vcc
C2
The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.
The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. / Tx Vcc.
A GND plane under the module is required for good EMI and sensitivity performance.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
4
LUMNDS1930-Aug0508
Rev A.0
155 Mbps Single Mode Transceiver
C-13-155-T-Sxx3(-55)-G5
Package Diagram (10.4 mm SC transceiver assembly)
LUMINENTOIC.COM
Top View
Front View
Side View
Rear View
Units: mm
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
5
LUMNDS1930-Aug0508
Rev A.0
155 Mbps Single Mode Transceiver
C-13-155-T-Sxx3(-55)-G5
Package Diagram (ST transceiver assembly)
y
Top View
Front View
Side View
Rear View
Top View
Front View
Units: mm
Package Diagram (FC transceiver assembly)
Rear View
Side View
LUMINENTOIC.COM
Units: mm
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
6
LUMNDS1930-Aug0508
Rev A.0
155 Mbps Single Mode Transceiver
C-13-155-T-Sxx3(-55)-G5
Ordering Information
Available Options:
C-13-155-T-SSC3-G5
C-13-155-T-SST3-G5
C-13-155-T-SFC3-G5
C-13-155-T-SSC3-55-G5
C-13-155-T-SST3-55-G5
C-13-155-T-SFC3-55-G5
Part numbering Definition:
C - 13 - 155 - T - S SC TxPower Temperature and Package
-xx
-RoHS
• 13 = Wavelength 1310nm
• Communication protocol (155 Mbps)
155 = PECL Signal Detection Output
• T = +5V Transceiver, FP
• Single mode fiber
• Connector options
SC/ST/FC
• Tx Power range
3= -15 to -8 dBm
• Temperature range and package
Blank = commercial temperature(0 to 70 ºC), 10.4 mm, Black case
• -55 = lead soldered
Blank = lead free solderd
• Blank = RoHS non-compliant product
G5 = RoHS compliant
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
7
LUMNDS1930-Aug0508
Rev A.0
155 Mbps Single Mode Transceiver
C-13-155-T-Sxx3(-55)-G5
Warnings:
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
Legal Notes:
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance
of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are
given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of
Sale for further warranty information.
LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual
property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes
no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers
using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from
such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any
actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© LuminentOIC, Inc. 2003
All rights reserved
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
8
LUMNDS1930-Aug0508
Rev A.0
Similar pages