IDT IDT54FCT237ATD Fast cmos octal transparent latch Datasheet

IDT54/74FCT373T/AT/CT/DT - 2373T/AT/CT
IDT54/74FCT533T/AT/CT
IDT54/74FCT573T/AT/CT/DT - 2573T/AT/CT
FAST CMOS OCTAL
TRANSPARENT
LATCHES
Integrated Device Technology, Inc.
– Reduced system switching noise
FEATURES:
• Common features:
– Low input and output leakage ≤1µA (max.)
– CMOS power levels
– True TTL input and output compatibility
– VOH = 3.3V (typ.)
– VOL = 0.3V (typ.)
– Meets or exceeds JEDEC standard 18 specifications
– Product available in Radiation Tolerant and Radiation
Enhanced versions
– Military product compliant to MIL-STD-883, Class B
and DESC listed (dual marked)
– Available in DIP, SOIC, SSOP, QSOP, CERPACK
and LCC packages
• Features for FCT373T/FCT533T/FCT573T:
– Std., A, C and D speed grades
– High drive outputs (-15mA IOH, 48mA IOL)
– Power off disable outputs permit “live insertion”
• Features for FCT2373T/FCT2573T:
– Std., A and C speed grades
– Resistor output
(-15mA IOH, 12mA IOL Com.)
(-12mA IOH, 12mA IOL Mil.)
DESCRIPTION:
The FCT373T/FCT2373T, FCT533T and FCT573T/
FCT2573T are octal transparent latches built using an advanced dual metal CMOS technology. These octal latches
have 3-state outputs and are intended for bus oriented applications. The flip-flops appear transparent to the data when
Latch Enable (LE) is HIGH. When LE is LOW, the data that
meets the set-up time is latched. Data appears on the bus
when the Output Enable (OE) is LOW. When OE is HIGH, the
bus output is in the high- impedance state.
The FCT2373T and FCT2573T have balanced drive outputs with current limiting resistors. This offers low ground
bounce, minimal undershoot and controlled output fall timesreducing the need for external series terminating resistors.
The FCT2xxxT parts are plug-in replacements for FCTxxxT
parts.
FUNCTIONAL BLOCK DIAGRAM IDT54/74FCT373T/2373T AND IDT54/74FCT573T/2573T
D0
D1
D
D2
D
D3
D
O
D
O
G
D4
D
O
G
D5
D
O
G
D6
D
O
G
D7
D
O
G
O
G
O
G
G
LE
OE
O0
O1
O2
O3
O4
O5
O6
O7
2564 cnv* 01
FUNCTIONAL BLOCK DIAGRAM IDT54/74FCT533T
D0
D1
D
D2
D
D3
D
O
D
O
G
D4
D
O
G
D5
D
O
G
D6
D
O
G
D7
D
O
G
O
G
O
G
G
LE
OE
O0
O1
O2
O3
MILITARY AND COMMERCIAL TEMPERATURE RANGES
1995 Integrated Device Technology, Inc.
O4
O5
O6
O7
2564 cnv* 02
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
6.12
AUGUST 1995
DSC-4216/6
1
IDT54/74FCT373T/AT/CT/DT - 2373T/AT/CT, IDT54/74FCT533T/AT/CT, IDT54/74FCT573T/AT/CT/DT - 2573T/AT/CT
FAST CMOS OCTAL TRANSPARENT LATCHES
MILITARY AND COMMERCIAL TEMPERATURE RANGES
PIN CONFIGURATIONS
O7
18
D7
4
O1
O2
5
D2
D3
7
O3
GND
6
P20-1
D20-1
SO20-2
SO20-7
SO20-8
&
E20-1
17
D6
16
O6
O1
5
15
O5
D5
O2
6
D2
D3
14
13
D4
9
12
O4
10
11
LE
8
3 2
4
D1
1
20 19
18
17
D7
D6
16
O6
7
15
O5
8
14
D5
L20-2
9 10 11 12 13
O3
GND
D0
D1
2564 cnv* 03
DIP/SOIC/SSOP/QSOP/CERPACK
TOP VIEW
D4
19
VCC
O7
2
3
OE
O0
VCC
O4
20
LE
1
D0
INDEX
OE
O0
IDT54/74FCT373/2373T
2564 cnv* 04
LCC
TOP VIEW
1
20
VCC
D0
2
3
19
O0
18
O1
O2
D2
4
D3
5
O3
O4
D4
6
D5
D6
D4
6
D5
7
D6
8
D7
GND
16
15
13
O5
O6
9
12
O7
10
11
LE
14
O1
17
O2
16
O3
7
15
O4
8
14
O5
L20-2
9 10 11 12 13
2564 cnv* 05
DIP/SOIC/SSOP/QSOP/CERPACK
TOP VIEW
O6
5
17
O7
D3
P20-1
D20-1
SO20-2
SO20-7
SO20-8
&
E20-1
20 19
18
1
LE
4
3 2
D7
GND
D1
D2
O0
OE
OE
VCC
D1
INDEX
D0
IDT54/74FCT573/2573T
2564 cnv* 06
LCC
TOP VIEW
O7
18
D7
D1
4
O1
5
O2
6
D2
7
P20-1
D20-1
SO20-2
&
E20-1
17
3 2
D6
D1
4
16
O6
O1
5
15
O5
O2
D2
D3
6
14
D5
D3
8
13
D4
O3
GND
9
12
O4
10
11
LE
1
20 19
18
17
D7
D6
16
O6
7
15
8
14
O5
D5
L20-2
9 10 11 12 13
2564 cnv* 07
DIP/SOIC/CERPACK
TOP VIEW
D4
19
VCC
O7
2
3
D0
OE
O0
O4
VCC
LE
20
O3
GND
1
D0
INDEX
OE
O0
IDT54/74FCT533
2564 cnv* 08
LCC
TOP VIEW
6.12
2
IDT54/74FCT373T/AT/CT/DT - 2373T/AT/CT, IDT54/74FCT533T/AT/CT, IDT54/74FCT573T/AT/CT/DT - 2573T/AT/CT
FAST CMOS OCTAL TRANSPARENT LATCHES
MILITARY AND COMMERCIAL TEMPERATURE RANGES
FUNCTION TABLE (533)(1)
Inputs
LE
DN
FUNCTION TABLE (373 and 573)(1)
Outputs
OE
ON
DN
Inputs
LE
OE
Outputs
ON
H
H
L
L
H
H
L
H
L
H
L
H
L
H
L
L
X
X
H
Z
X
X
H
Z
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
X = Don’t Care
Z = High Impedance
2564 tbl 01
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
X = Don’t Care
Z = High Impedance
2564 tbl 02
DEFINITION OF FUNCTIONAL TERMS
Pin Names
DN
Description
Data Inputs
LE
Latch Enable Input (Active HIGH)
OE
Output Enable Input (Active LOW)
ON
3-State Outputs
ON
Complementary 3-State Outputs
2564 tbll 03
ABSOLUTE MAXIMUM RATINGS(1)
Symbol
Rating
Commercial
VTERM(2) Terminal Voltage
–0.5 to +7.0
with Respect to
GND
VTERM(3) Terminal Voltage
–0.5 to
with Respect to
VCC +0.5
GND
TA
Operating
0 to +70
Temperature
TBIAS
Temperature
–55 to +125
Under Bias
TSTG
Storage
–55 to +125
Temperature
PT
Power Dissipation
0.5
I OUT
DC Output
Current
–60 to +120
CAPACITANCE (TA = +25°C, f = 1.0MHz)
Military
–0.5 to +7.0
Unit
V
–0.5 to
VCC +0.5
V
–55 to +125
°C
–65 to +135
°C
–65 to +150
°C
0.5
W
–60 to +120
mA
Symbol
Parameter(1)
CIN
Input
Capacitance
COUT
Output
Capacitance
Conditions
VIN = 0V
Typ.
6
VOUT = 0V
8
Max. Unit
10
pF
12
NOTE:
1. This parameter is measured at characterization but not tested.
pF
2564 lnk 05
2564 lnk 04
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions
above those indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating conditions for
extended periods may affect reliability. No terminal voltage may exceed
VCC by +0.5V unless otherwise noted.
2. Input and VCC terminals only.
3. Outputs and I/O terminals only.
6.12
3
IDT54/74FCT373T/AT/CT/DT - 2373T/AT/CT, IDT54/74FCT533T/AT/CT, IDT54/74FCT573T/AT/CT/DT - 2573T/AT/CT
FAST CMOS OCTAL TRANSPARENT LATCHES
MILITARY AND COMMERCIAL TEMPERATURE RANGES
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Commercial: TA = 0°C to +70°C, VCC = 5.0V ± 5%; Military: TA = –55°C to +125°C, VCC = 5.0V ± 10%
Symbol
VIH
Parameter
Input HIGH Level
Test Conditions(1)
Guaranteed Logic HIGH Level
Min.
2.0
Typ.(2)
—
Max.
—
Unit
V
VIL
Input LOW Level
Guaranteed Logic LOW Level
—
—
0.8
V
II H
Input HIGH Current(4)
VCC = Max.
VI = 2.7V
—
—
±1
µA
II L
Input LOW Current (4)
VI = 0.5V
—
—
±1
I OZH
High Impedance Output Current
I OZL
(3-State Output pins) (4)
II
Input HIGH Current(4)
VCC = Max., VI = VCC (Max.)
VIK
Clamp Diode Voltage
VH
Input Hysteresis
I CC
Quiescent Power Supply Current
VO = 2.7V
—
—
±1
VO = 0.5V
—
—
±1
—
—
±1
VCC = Min., IIN = –18mA
—
–0.7
–1.2
V
—
—
200
—
mV
—
0.01
1
VCC = Max.
VCC = Max., VIN = GND or VCC
µA
µA
mA
2564 lnk 06
OUTPUT DRIVE CHARACTERISTICS FOR FCT373T/533T/573T
VOL
Output LOW Voltage
I OS
Short Circuit Current
Test Conditions(1)
VCC = Min.
I OH = –6mA MIL.
VIN = VIH or V IL
I OH = –8mA COM'L.
I OH = –12mA MIL.
I OH = –15mA COM'L.
VCC = Min.
I OL = 32mA MIL.
VIN = VIH or V IL
I OL = 48mA COM'L.
VCC = Max., VO = GND (3)
I OFF
Input/Output Power Off Leakage(5)
VCC = 0V, VIN or V O ≤ 4.5V
Symbol
VOH
Parameter
Output HIGH Voltage
Min.
2.4
Typ.(2)
3.3
Max.
—
Unit
V
2.0
3.0
—
V
—
0.3
0.5
V
–60
–120
–225
mA
—
—
±1
µA
2564 lnk 07
OUTPUT DRIVE CHARACTERISTICS FOR FCT2373T/2573T
Symbol
I ODL
Parameter
Output LOW Current
Test Conditions(1)
VCC = 5V, VIN = VIH or VIL, VOUT = 1.5V (3)
Min.
16
Typ.(2)
48
Max.
—
Unit
mA
I ODH
Output HIGH Current
VCC = 5V, VIN = VIH or V IL, VOUT = 1.5V (3)
–16
–48
—
mA
VOH
Output HIGH Voltage
2.4
3.3
—
V
VOL
Output LOW Voltage
VCC = Min.
VIN = VIH or VIL
VCC = Min.
VIN = VIH or V IL
—
0.3
0.50
V
I OH = –12mA MIL.
I OH = –15mA COM'L.
I OL = 12mA
NOTES:
1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at Vcc = 5.0V, +25°C ambient.
3. Not more than one output should be shorted at one time. Duration of the short circuit test should not exceed one second.
4. The test limit for this parameter is ±5µA at TA = –55°C.
5. This parameter is guaranteed but not tested.
6.12
2564 lnk 08
4
IDT54/74FCT373T/AT/CT/DT - 2373T/AT/CT, IDT54/74FCT533T/AT/CT, IDT54/74FCT573T/AT/CT/DT - 2573T/AT/CT
FAST CMOS OCTAL TRANSPARENT LATCHES
MILITARY AND COMMERCIAL TEMPERATURE RANGES
POWER SUPPLY CHARACTERISTICS
Symbol
∆ICC
ICCD
IC
Parameter
Quiescent Power Supply Current
TTL Inputs HIGH
Dynamic Power Supply
Current(4)
Total Power Supply Current (6)
Test Conditions(1)
VCC = Max.
VIN = 3.4V(3)
VCC = Max.
Outputs Open
OE = GND
One Input Toggling
50% Duty Cycle
VCC = Max.
Outputs Open
fi = 10MHz
50% Duty Cycle
OE = GND
LE = VCC
One Bit Toggling
VCC = Max.
Outputs Open
fi = 2.5MHz
50% Duty Cycle
OE = GND
LE = VCC
Eight Bits Toggling
Min.
—
Typ.(2)
0.5
Max.
2.0
Unit
mA
mA/
MHz
VIN = VCC FCTxxxT
VIN = GND
FCT2xxxT
—
0.15
0.25
—
0.06
0.12
VIN = VCC
—
1.5
3.5
VIN = GND FCT2xxxT
—
0.6
2.2
FCTxxxT
VIN = 3.4
VIN = GND
FCT2xxxT
—
1.8
4.5
0.9
3.2
VIN = VCC
—
3.0
6.0 (5)
VIN = GND FCT2xxxT
—
1.2
3.4 (5)
FCTxxxT
VIN = 3.4
VIN = GND
FCT2xxxT
—
5.0
14.0 (5)
—
3.2
11.4 (5)
FCTxxxT
FCTxxxT
NOTES:
1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 5.0V, +25°C ambient.
3. Per TTL driven input (VIN = 3.4V). All other inputs at VCC or GND.
4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations.
5. Values for these conditions are examples of the ICC formula. These limits are guaranteed but not tested.
6. IC = IQUIESCENT + IINPUTS + IDYNAMIC
IC = ICC + ∆ICC DHNT + ICCD (fCP/2 + fiNi)
ICC = Quiescent Current
∆ICC = Power Supply Current for a TTL High Input (VIN = 3.4V)
DH = Duty Cycle for TTL Inputs High
NT = Number of TTL Inputs at DH
ICCD = Dynamic Current Caused by an Input Transition Pair (HLH or LHL)
fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices)
fi = Input Frequency
Ni = Number of Inputs at fi
All currents are in milliamps and all frequencies are in megahertz.
6.12
mA
2564 tbl 09
5
IDT54/74FCT373T/AT/CT/DT - 2373T/AT/CT, IDT54/74FCT533T/AT/CT, IDT54/74FCT573T/AT/CT/DT - 2573T/AT/CT
FAST CMOS OCTAL TRANSPARENT LATCHES
MILITARY AND COMMERCIAL TEMPERATURE RANGES
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
FCT373T/2373T/573T/2573T
Com'l.
Symbol
Parameter
Conditions(1)
Min.(2)
CL = 50pF
1.5
FCT373AT/2373AT/573AT/2573AT
Mil.
Max.
Min.(2)
8.0
1.5
Com'l.
Max.
Min.(2)
8.5
1.5
Mil.
Max.
Min.(2)
Max.
Unit
5.2
1.5
5.6
ns
tPLH
tPHL
Propagation Delay
DN to ON
tPLH
tPHL
tPZH
tPZL
tPHZ
tPLZ
tSU
Propagation Delay
LE to ON
Output Enable Time
2.0
13.0
2.0
15.0
2.0
8.5
2.0
9.8
ns
1.5
12.0
1.5
13.5
1.5
6.5
1.5
7.5
ns
Output Disable Time
1.5
7.5
1.5
10.0
1.5
5.5
1.5
6.5
ns
Set-up Time HIGH
or LOW, DN to LE
Hold Time HIGH
or LOW, DN to LE
LE Pulse Width HIGH
2.0
—
2.0
—
2.0
—
2.0
—
ns
1.5
—
1.5
—
1.5
—
1.5
—
ns
6.0
—
6.0
—
5.0
—
6.0
—
tH
tW
RL = 500Ω
ns
2564 tbl 10
FCT373CT/2373CT/573CT/2573CT
Com'l.
Symbol
Parameter
FCT373DT/573DT
Mil.
Com'l.
Mil.
Conditions(1)
Min.(2)
Max.
Min.(2)
Max.
Min.(2)
Max.
Min.(2)
Max.
Unit
CL = 50pF
1.5
4.2
1.5
5.1
1.5
3.8
—
—
ns
tPLH
tPHL
Propagation Delay
DN to ON
tPLH
tPHL
tPZH
tPZL
tPHZ
tPLZ
tSU
Propagation Delay
LE to ON
Output Enable Time
2.0
5.5
2.0
8.0
2.0
4.0
—
—
ns
1.5
5.5
1.5
6.3
1.5
4.8
—
—
ns
Output Disable Time
1.5
5.0
1.5
5.9
1.5
4.0
—
—
ns
Set-up Time HIGH
or LOW, DN to LE
Hold Time HIGH
or LOW, DN to LE
LE Pulse Width HIGH (3)
2.0
—
2.0
—
1.5
—
—
—
ns
1.5
—
1.5
—
1.0
—
—
—
ns
5.0
—
6.0
—
3.0
—
—
—
tH
tW
RL = 500Ω
ns
2564 tbl 11
FCT533T
Com'l.
Symbol
Parameter
tPLH
tPHL
Propagation Delay
DN to ON
tPLH
tPHL
tPZH
tPZL
tPHZ
tPLZ
tSU
Propagation Delay
LE to ON
Output Enable
Time
Output Disable
Time
Set-up Time HIGH
or LOW, DN to LE
Hold Time HIGH
or LOW, DN to LE
LE Pulse Width HIGH
tH
tW
FCT533AT
Mil.
Com'l.
FCT533CT
Mil.
Com'l.
Mil.
Conditions (1) Min.(2) Max. Min.(2) Max. Min.(2) Max. Min.(2) Max. Min.(2) Max. Min.(2) Max. Unit
CL = 50pF
1.5
10.0
1.5
12.0
1.5
5.2
1.5
5.6
1.5
4.2
1.5
5.1
ns
2.0
13.0
2.0
14.0
2.0
8.5
2.0
9.8
2.0
5.5
2.0
8.0
ns
1.5
11.0
1.5
12.5
1.5
6.5
1.5
7.5
1.5
5.5
1.5
6.3
ns
1.5
7.0
1.5
8.5
1.5
5.5
1.5
6.5
1.5
5.0
1.5
5.9
ns
2.0
—
2.0
—
2.0
—
2.0
—
2.0
—
2.0
—
ns
1.5
—
1.5
—
1.5
—
1.5
—
1.5
—
1.5
—
ns
6.0
—
6.0
—
5.0
—
6.0
—
5.0
—
6.0
—
ns
RL = 500Ω
NOTES:
1. See test circuit and waveforms.
2. Minimum limits are guaranteed but not tested on Propagation Delays.
3. This parameter is guaranteed but not tested.
2564 tbl 12
6.12
6
IDT54/74FCT373T/AT/CT/DT - 2373T/AT/CT, IDT54/74FCT533T/AT/CT, IDT54/74FCT573T/AT/CT/DT - 2573T/AT/CT
FAST CMOS OCTAL TRANSPARENT LATCHES
MILITARY AND COMMERCIAL TEMPERATURE RANGES
TEST CIRCUITS AND WAVEFORMS
SWITCH POSITION
TEST CIRCUITS FOR ALL OUTPUTS
V CC
7.0V
500Ω
Pulse
Generator
Open Drain
Disable Low
Closed
Open
All Other Tests
D.U.T.
50pF
RT
Switch
Enable Low
V OUT
VIN
Test
2564 lnk 13
DEFINITIONS:
CL= Load capacitance: includes jig and probe capacitance.
RT = Termination resistance: should be equal to ZOUT of the Pulse
Generator.
500Ω
CL
2564 drw 09
SET-UP, HOLD AND RELEASE TIMES
DATA
INPUT
TIMING
INPUT
ASYNCHRONOUS CONTROL
PRESET
CLEAR
ETC.
SYNCHRONOUS CONTROL
PRESET
CLEAR
CLOCK ENABLE
ETC.
tH
tSU
tREM
tSU
PULSE WIDTH
3V
1.5V
0V
3V
1.5V
0V
LOW-HIGH-LOW
PULSE
1.5V
tW
3V
1.5V
0V
HIGH-LOW-HIGH
PULSE
1.5V
3V
1.5V
0V
tH
2564 drw 11
2564 drw 10
PROPAGATION DELAY
ENABLE AND DISABLE TIMES
ENABLE
SAME PHASE
INPUT TRANSITION
tPLH
tPHL
OUTPUT
tPLH
OPPOSITE PHASE
INPUT TRANSITION
tPHL
3V
1.5V
0V
VOH
1.5V
VOL
DISABLE
3V
1.5V
CONTROL
INPUT
tPZL
OUTPUT
NORMALLY
LOW
3V
1.5V
0V
SWITCH
CLOSED
3.5V
1.5V
tPZH
OUTPUT
NORMALLY
HIGH
2564 drw 12
SWITCH
OPEN
0V
tPLZ
3.5V
0.3V
VOL
tPHZ
0.3V
1.5V
0V
VOH
0V
2564 drw 13
NOTES:
1. Diagram shown for input Control Enable-LOW and input Control DisableHIGH
2. Pulse Generator for All Pulses: Rate ≤ 1.0MHz; tF ≤ 2.5ns; tR ≤ 2.5ns
6.12
7
IDT54/74FCT373T/AT/CT/DT - 2373T/AT/CT, IDT54/74FCT533T/AT/CT, IDT54/74FCT573T/AT/CT/DT - 2573T/AT/CT
FAST CMOS OCTAL TRANSPARENT LATCHES
MILITARY AND COMMERCIAL TEMPERATURE RANGES
ORDERING INFORMATION
IDT
XX
FCT
Temp. Range
X
Family
XXXX
Device Type
X
Package
X
Process
Blank
B
Commercial
MIL-STD-883, Class B
P
D
SO
L
E
PY
Q
Plastic DIP
CERDIP
Small Outline IC
Leadless Chip Carrier
CERPACK
Shrink Small Outline Package
Quarter-size Small Outline Package
373T
573T
533T
373AT
573AT
533AT
373CT
573CT
533CT
373DT
573DT
Non-Inverting Octal Transparent Latch
Non-Inverting Octal Transparent Latch
Inverting Octal Transparent Latch
Blank
2
High Drive
Balanced Drive
54
74
–55°C to +125°C
0°C to +70°C
2564 drw 14
6.12
8
Similar pages