Bytes HER1604 16.0 amp high efficiency rectifier Datasheet

HER1601
THRU
HER1606
16.0 AMP HIGH EFFICIENCY RECTIFIERS
VOLTAGE RANGE
50 to 600 Volts
CURRENT
16.0 Ampere
FEATURES
* Low forward voltage drop
* High current capability
* High reliability
* High surge current capability
* High speed switching
TO-220
3.8 φ +.2
HOLE THRU
.412
(10.5)
MAX.
.108
(2.75)
.248
(6.3)
MECHANICAL DATA
* Case: Molded plastic
* Epoxy: UL 94V-0 rate flame retardant
* Lead: Lead solderable per MIL-STD-202,
method 208 guranteed
* Polarity: As Marked
* Mounting position: Any
.050
(1.27)
.595
(15.1)
MAX.
.550
(14.0)
.158
(4.0) MIN.
MAX.
.051 MAX.
(1.3)
.040 MAX.
(1.0)
.100
(2.54)
* Weight: 2.24 grams
.180
(4.6)
.120
(3.05)
PIN 1
+
PIN 1
PIN 3
CASE
PIN 2
PIN 3
Positive CT
Suffix "C"
CASE
PIN 2
Negative CT
Suffix "A"
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating 25 C ambient temperature uniess otherwies specified.
Single phase half wave, 60Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
TYPE NUMBER
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward Rectified Current
HER1601
50
35
50
HER1602 HER1603 HER1604 HER1605 HER1606 UNITS
100
70
100
200
140
200
.375"(9.5mm) Lead Length at Tc=75 C
Peak Forward Surge Current, 8.3 ms single half sine-wave
300
210
300
400
280
400
600
420
600
A
16.0
200
superimposed on rated load (JEDEC method)
Maximum Instantaneous Forward Voltage at 8.0A
Maximum DC Reverse Current
Tc=25 C
1.0
1.3
1.85
10.0
at Rated DC Blocking Voltage
Tc=100 C
Maximum Reverse Recovery Time (Note 1)
Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range TJ, TSTG
200
60
100
-55
NOTES:
1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A
2. Measured at 1MHz and applied reverse voltage of 4.0V D.C.
76
65
+150
V
V
V
A
V
µA
µA
nS
pF
C
RATING AND CHARACTERISTIC CURVES (HER1601 THRU HER1606)
FIG.1-TYPICAL FORWARD
FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE
CHARACTERISTICS
AVERAGE FORWARD CURRENT,(A)
05
03
6
60
HE
R1
HE
R1
R1
60
60
4-
16
16
1-
10.0
HE
1.0
24
20
16
12
Single Phase Half Wave 60Hz
8
Resistive Or Inductive Load
4
0
0
20
40
Tj=25 C
60
80
100
120
140
160
180
200
CASE TEMPERATURE ( C)
Pulse Width 300us
1% Duty Cycle
.1
.01
.2
.4
.6
.8
1.0
1.2
1.4
1.6
FORWARD VOLTAGE,(V)
FIG.3- TEST CIRCUIT DIAGRAM AND REVERSE
RECOVERY TIME CHARACTERISTICS
50Ω
NONINDUCTIVE
10Ω
NONINDUCTIVE
( )
(+)
D.U.T.
25Vdc
(approx.)
PULSE
GENERATOR
(NOTE 2)
( )
1Ω
NONINDUCTIVE
OSCILLISCOPE
(NOTE 1)
PEAK FORWAARD SURGE CURRENT,(A)
FIG.4-MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT
250
200
150
Sine Wave
100
JEDEC method
50
0
1
|
|
|
|
|
|
|
|
0
-0.25A
1cm
100
175
150
125
100
75
50
25
0
-1.0A
50
10
FIG.5-TYPICAL JUNCTION CAPACITANCE
2. Rise Time= 10ns max., Source Impedance= 50 ohms.
+0.5A
5
NUMBER OF CYCLES AT 60Hz
NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF.
trr
8.3ms Single Half
Tj=25 C
(+)
JUNCTION CAPACITANCE,(pF)
INSTANTANEOUS FORWARD CURRENT,(A)
100
0.1
SET TIME BASE FOR
0.5
1
2
5
10
20
REVERSE VOLTAGE,(V)
50 / 10ns / cm
77
50
100
200
500
1000
Similar pages