AIMTEC AM1L-1203SH30-N 1 watt dc-dc converter Datasheet

AM1L-N Series
•
SMD PACKAGE
•
LOW RIPPLE & NOISE
•
HIGH EFFICIENCY UP TO 75%
•
UL94-VO PACKAGE
•
INPUT/OUTPUT ISOLATION: 1000 & 3000VDC
•
OPERATING TEMPERATURE: -40°C ... +85°C
•
PIN-COMPATIBLE WITH MULTIPLE MANUFACTURERS
GENERAL DESCRIPTION
Our AM1L-N series is a family of cost effective 1W single and dual output DC-DC converters. These converters
combines a miniature SMD package with 1000 &
3000VDC input/output isolation voltage.
Ninety six models operate from input voltages of 3.3, 5, 12 & 24VDC
with producing output voltage levels of 3.3, 5, 9, 12, 15, 24, ±3.3, ±5,
±9, ±12, ±15 & ±24VDC. Full SMD-design and a 100% production
test of parameters ensures a high reliability in this product.
ELECTRICAL SPECIFICATIONS
Specifications typical at +25°C, nominal input voltage, rated output current unless otherwise specified
Input Specifications:
Voltage range
Filter
±10 %
Capacitor
Isolation Specifications:
Rated voltage (60 sec)
Resistance
Capacitance
1000 & 3000VDC
> 1000MOhm
60pF, typ.
Output Specifications:
Voltage accuracy
Voltage balance (Dual Output)
Ripple & noise (at 20MHz BW)
Short circuit protection
Line voltage regulation
Load voltage regulation
Temperature Coefficient
General Specifications:
Efficiency
Switching Frequency
75% (typ)
100KHz, typ. 100% load
Physical Specifications
Dimensions
single out
dual out
single & dual 3000VDC
Weight
Case material
12.7x11.2x6.3 mm
15.3x11.2x6.3 mm
15.2x11.2x6.25 mm
1.5 g
Plastic UL94-VO
±5%, max.
±2%
150mVp-p, max.
1 sec.
±1.2%/1% of Vin, max.
10% max.
(load 10...100%)
±0.03%/°C, max.
DC-DC CONVERTERS
1 watt dc-dc converters
Environmental Specifications:
Operating temperature (ambient) -40°C ... +85°C
Storage temperature
-55°C ... +125°C
Case temperature
+95°C, max.
Derating
None required
Humidity (non-condensing)
Up to 90%
Cooling
Free-air Convection
MTBF: > 980,000 hrs single, > 1,000,000 hrs dual (MIL-HDBK-217F, Ground Benign, t=+25°C)
Specifications are subject to change without notification
OUTLINE DIMENSIONS FOR SINGLE OUTPUT MODELS
Pin
Single
1
2
4
5
3
6
7
8
-V Input
+V Input
-V Output
+V Output
N.C.
N.C.
N.C.
N.C.
Continued on next page
VISIT US AT WWW.AIMTEC.CA
27
AM1L-N Series
MODELS
Single output
DC-DC CONVERTERS
Models
Isolation 1000VDC
Isolation 3000VDC
AM1L-0303S-N
AM1L-0305S-N
AM1L-0309S-N
AM1L-0312S-N
AM1L-0315S-N
AM1L-0324S-N
AM1L-0503S-N
AM1L-0505S-N
AM1L-0509S-N
AM1L-0512S-N
AM1L-0515S-N
AM1L-0524S-N
AM1L-1203S-N
AM1L-1205S-N
AM1L-1209S-N
AM1L-1212S-N
AM1L-1215S-N
AM1L-1224S-N
AM1L-2403S-N
AM1L-2405S-N
AM1L-2409S-N
AM1L-2412S-N
AM1L-2415S-N
AM1L-2424S-N
AM1L-0303SH30-N
AM1L-0305SH30-N
AM1L-0309SH30-N
AM1L-0312SH30-N
AM1L-0315SH30-N
AM1L-0324SH30-N
AM1L-0503SH30-N
AM1L-0505SH30-N
AM1L-0509SH30-N
AM1L-0512SH30-N
AM1L-0515SH30-N
AM1L-0524SH30-N
AM1L-1203SH30-N
AM1L-1205SH30-N
AM1L-1209SH30-N
AM1L-1212SH30-N
AM1L-1215SH30-N
AM1L-1224SH30-N
AM1L-2403SH30-N
AM1L-2405SH30-N
AM1L-2409SH30-N
AM1L-2412SH30-N
AM1L-2415SH30-N
AM1L-2424SH30-N
Input Voltage
3.3V±10%
5V±10%
12V±10%
24V±10%
Ouput Voltage
Ouput Current max.
3.3VDC
5VDC
9VDC
12VDC
15VDC
24VDC
3.3VDC
5VDC
9VDC
12VDC
15VDC
24VDC
3.3VDC
5VDC
9VDC
12VDC
15VDC
24VDC
3.3VDC
5VDC
9VDC
12VDC
15VDC
24VDC
304mA
200mA
111mA
84mA
67mA
40mA
304mA
200mA
111mA
84mA
67mA
40mA
304mA
200mA
111mA
84mA
67mA
40mA
304mA
200mA
111mA
84mA
67mA
40mA
ISOLATED & UNREGULATED
<Figure 1>
<Figure 2>
<Figure 3>
<Figure 4>
External Capacitor Table
Vin
External
Capacitor
Vout
External
Capacitor
5VDC
12VDC
-
4.7uF
2.2uF
-
5VDC
9VDC
12VDC
15VDC
10uF
4.7uF
2.2uF
1uF
Note: The selected voltage withstand of the capacitor is generally
1.5~2 times of the nominal voltage.
28
TO ORDER CALL 1-888-9-AIMTEC
AM1L-N Series
Dual output
Models
Isolation 1000VDC
Isolation 3000VDC
AM1L-0303D-N
AM1L-0305D-N
AM1L-0309D-N
AM1L-0312D-N
AM1L-0315D-N
AM1L-0324D-N
AM1L-0503D-N
AM1L-0505D-N
AM1L-0509D-N
AM1L-0512D-N
AM1L-0515D-N
AM1L-0524D-N
AM1L-1203D-N
AM1L-1205D-N
AM1L-1209D-N
AM1L-1212D-N
AM1L-1215D-N
AM1L-1224D-N
AM1L-2403D-N
AM1L-2405D-N
AM1L-2409D-N
AM1L-2412D-N
AM1L-2415D-N
AM1L-2424D-N
AM1L-0303DH30-N
AM1L-0305DH30-N
AM1L-0309DH30-N
AM1L-0312DH30-N
AM1L-0315DH30-N
AM1L-0324DH30-N
AM1L-0503DH30-N
AM1L-0505DH30-N
AM1L-0509DH30-N
AM1L-0512DH30-N
AM1L-0515DH30-N
AM1L-0524DH30-N
AM1L-1203DH30-N
AM1L-1205DH30-N
AM1L-1209DH30-N
AM1L-1212DH30-N
AM1L-1215DH30-N
AM1L-1224DH30-N
AM1L-2403DH30-N
AM1L-2405DH30-N
AM1L-2409DH30-N
AM1L-2412DH30-N
AM1L-2415DH30-N
AM1L-2424DH30-N
Input Voltage
Ouput Voltage
±3.3VDC
±5VDC
±9VDC
±12VDC
±15VDC
±24VDC
±3.3VDC
±5VDC
±9VDC
±12VDC
±15VDC
±24VDC
±3.3VDC
±5VDC
±9VDC
±12VDC
±15VDC
±24VDC
±3.3VDC
±5VDC
±9VDC
±12VDC
±15VDC
±24VDC
3.3V±10%
5V±10%
12V±10%
24V±10%
Ouput Current max.
±152mA
±100mA
±56mA
±42mA
±33mA
±20mA
±152mA
±100mA
±56mA
±42mA
±33mA
±20mA
±152mA
±100mA
±56mA
±42mA
±33mA
±20mA
±152mA
±100mA
±56mA
±42mA
±33mA
±20mA
DC-DC CONVERTERS
MODELS
ISOLATED &
UNREGULATED
<Figure 2>
<Figure 1>
<Figure 4>
<Figure 3>
OUTLINE DIMENSIONS FOR DUAL OUTPUT MODELS
Pin
Dual
1
2
3
4
5
6
7
8
9
10
-V Input
+V Input
N.C.
Common
-V Output
N.C.
+V Output
N.C.
N.C.
N.C.
External Capacitor Table
Vin
External
Capacitor
Vout
External
Capacitor
5VDC
12VDC
-
4.7uF
2.2uF
-
5VDC
9VDC
12VDC
15VDC
4.7uF
2.2uF
1uF
0.47uF
Note: The selected voltage withstand of the capacitor is
generally 1.5~2 times of the nominal voltage.
Continued on next page
VISIT US AT WWW.AIMTEC.CA
29
AM1L-N Series
OUTLINE DIMENSIONS FOR SINGLE & DUAL OUTPUT MODELS (3000VDC)
DC-DC CONVERTERS
Pin
TYPICAL CHARACTERISTICS
1
2
3
4
5
6
7
8
9
10
11
12
3000VDC
Single
Dual
GND
+V Input
N.C.
Omitted
Common
N.C.
N.C.
+V Output
Omitted
N.C.
N.C.
N.C.
GND
+V Input
N.C.
Omitted
Common
-V Output
N.C.
+V Output
Omitted
N.C.
N.C.
N.C.
APPLICATION NOTE
General Application
In regular circuits, our company’s DC/DC converters may be used directly
without any peripheral components (see Figure 2). The basic input/output
isolation may be used to provide a group of simple isolated polar output
power supplies or to generate power supply lines of different voltages.
Voltage And Polarity Inversion
A key performance of this DC/DC converter is high electric isolation
capability. Thus, only one DC/DC converter may allow for several potential
differences in the layout of circuit board. If necessary, you may connect the
output end of the positive to input ground, then the negative output end will
generate a negative voltage (see Figure 1).
Filtering
In some circuits which are sensitive to noise and ripple, a filtering capacitor
may be added to the DC/DC output end and input end to reduce the noise
and ripple. However, the capacitance of the output filter capacitor must be
proper. If the capacitance is too big, a startup problem might arise. For
every channel of output provided the safe and reliable operation is
ensured, the greatest capacitance of its filtering capacitor sees the
External Capacitor Table. To get an extremely low ripple, a “LC” filter
network may be connected to the input and output ends of the DC/DC
converter, which may produce a more significant filtering effect. It should
also be noted that the inductance and the frequency of the “LC” filter
network should be staggered with the DC/DC frequency to avoid mutual
interference (see Figure 3).
30
Requirement On Output Load
To ensure this module can operate efficiently and reliably, a minimum load
is specified for this kind of DC/DC converter in addition to a maximum load
(namely full load). During operation, make sure the specified range of input
voltage is not exceeded, the minimum output load is not less than 10% of
the full load, and that this product should never be operated under no load!!!
If the actual output power is very small, please connect a resistor with
proper resistance at the output end in parallel to increase the load.
Overload Protection
Under normal operating conditions, the output circuit of these products has
no protection against over-current and short-circuits. The simplest method
is to connect a self-recovery fuse in series at the input end or add a circuit
breaker to the circuits.
Output Voltage Regulation and Over-voltage Protection Circuit
The simplest device for output voltage regulation, over-voltage and overcurrent protection is a linear voltage stabilizer with overheat protection that
is connected to the input or output end in series (see Figure 4).
Product Reliability
The MTBF is the mean time between failures under full load. If the actual
load is less than 20% of the rated load or greater than the rated load, then
this productís reliability will be greatly reduced.
Input Polarity Protection
Under normal conditions, this productís input circuit has no protection
against polarity inversion; the solution is to connect a diode in series at the
input.
TO ORDER CALL 1-888-9-AIMTEC
Similar pages