ATMEL AT32UC3B1256-Z1UT 32-bit microcontroller Datasheet

Features
• High Performance, Low Power AVR®32 UC 32-Bit Microcontroller
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
– Compact Single-cycle RISC Instruction Set Including DSP Instruction Set
– Read-Modify-Write Instructions and Atomic Bit Manipulation
– Performing 1.38 DMIPS / MHz
Up to 75 DMIPS Running at 60 MHz from Flash
Up to 45 DMIPS Running at 33 MHz from Fash
– Memory Protection Unit
Multi-hierarchy Bus System
– High-Performance Data Transfers on Separate Buses for IIncreased Performance
– 7 Peripheral DMA Channels Improves Speed for Peripheral Communication
Internal High-Speed Flash
– 256K Bytes, 128K Bytes, 64K Bytes Versions
– Single Cycle Access up to 30 MHz
– Prefetch Buffer Optimizing Instruction Execution at Maximum Speed
– 4ms Page Programming Time and 8ms Full-Chip Erase Time
– 100,000 Write Cycles, 15-year Data Retention Capability
– Flash Security Locks and User Defined Configuration Area
Internal High-Speed SRAM, Single-Cycle Access at Full Speed
– 32K Bytes (256KB and 128KB Flash), 16K Bytes (64KB Flash)
Interrupt Controller
– Autovectored Low Latency Interrupt Service with Programmable Priority
System Functions
– Power and Clock Manager Including Internal RC Clock and One 32KHz Oscillator
– Two Multipurpose Oscillators and Two Phase-Lock-Loop (PLL) allowing
Independant CPU Frequency from USB Frequency
– Watchdog Timer, Real-Time Clock Timer
Universal Serial Bus (USB)
– Device 2.0 Full/Low Speed and On-The-Go (OTG)
– Flexible End-Point Configuration and Management with Dedicated DMA Channels
– On-chip Transceivers Including Pull-Ups
– USB Wake Up from Sleep Functionality
One Three-Channel 16-bit Timer/Counter (TC)
– Three External Clock Inputs, PWM, Capture and Various Counting Capabilities
One 7-Channel 16-bit Pulse Width Modulation Controller (PWM)
Three Universal Synchronous/Asynchronous Receiver/Transmitters (USART)
– Independant Baudrate Generator, Support for SPI, IrDA and ISO7816 interfaces
– Support for Hardware Handshaking, RS485 Interfaces and Modem Line
One Master/Slave Serial Peripheral Interfaces (SPI) with Chip Select Signals
One Synchronous Serial Protocol Controller
– Supports I2S and Generic Frame-Based Protocols
One Master/Slave Two-Wire Interface (TWI), 400kbit/s I2C-compatible
One 8-channel 10-bit Analog-To-Digital Converter
On-Chip Debug System (JTAG interface)
– Nexus Class 2+, Runtime Control, Non-Intrusive Data and Program Trace
64-pin TQFP/QFN (44 GPIO pins), 48-pin TQFP/QFN (28 GPIO pins)
5V Input Tolerant I/Os, including 4 high-drive pins.
Single 3.3V Power Supply or Dual 1.8V-3.3V Power Supply
AVR®32
32-Bit
Microcontroller
AT32UC3B0256
AT32UC3B0128
AT32UC3B064
AT32UC3B1256
AT32UC3B1128
AT32UC3B164
Preliminary
Summary
32059ES–AVR32–12/07
AT32UC3B
1. Description
The AT32UC3B is a complete System-On-Chip microcontroller based on the AVR32 UC RISC
processor running at frequencies up to 60 MHz. AVR32 UC is a high-performance 32-bit RISC
microprocessor core, designed for cost-sensitive embedded applications, with particular emphasis on low power consumption, high code density and high performance.
The processor implements a Memory Protection Unit (MPU) and a fast and flexible interrupt controller for supporting modern operating systems and real-time operating systems.
Higher computation capability is achieved using a rich set of DSP instructions.
The AT32UC3B incorporates on-chip Flash and SRAM memories for secure and fast access.
The Peripheral Direct Memory Access controller enables data transfers between peripherals and
memories without processor involvement. PDC drastically reduces processing overhead when
transferring continuous and large data streams between modules within the MCU.
The Power Manager improves design flexibility and security: the on-chip Brown-Out Detector
monitors the power supply, the CPU runs from the on-chip RC oscillator or from one of external
oscillator sources, a Real-Time Clock and its associated timer keeps track of the time.
The Timer/Counter includes three identical 16-bit timer/counter channels. Each channel can be
independently programmed to perform frequency measurement, event counting, interval measurement, pulse generation, delay timing and pulse width modulation.
The PWM modules provides seven independent channels with many configuration options
including polarity, edge alignment and waveform non overlap control. One PWM channel can
trigger ADC conversions for more accurate close loop control implementations.
The AT32UC3B also features many communication interfaces for communication intensive
applications. In addition to standard serial interfaces like UART, SPI or TWI, other interfaces like
flexible Synchronous Serial Controller and USB are available.
The Synchronous Serial Controller provides easy access to serial communication protocols and
audio standards like I2S, UART or SPI.
The Full-Speed USB 2.0 Device interface supports several USB Classes at the same time
thanks to the rich End-Point configuration. The On-The-GO (OTG) Host interface allows device
like a USB Flash disk or a USB printer to be directly connected to the processor.
AT32UC3B integrates a class 2+ Nexus 2.0 On-Chip Debug (OCD) System, with non-intrusive
real-time trace, full-speed read/write memory access in addition to basic runtime control. The
Nanotrace interface enables trace feature for JTAG-based debuggers.
2
32059ES–AVR32–12/07
AT32UC3B
2. Configuration Summary
The table below lists all AT32UC3B memory and package configurations:
Device
Flash
SRAM
USART
SSC
ADC
OSC
USB Configuration
Package
AT32UC3B0256
256 Kbytes
32 Kbytes
3
1
8
2
Mini-Host + Device
64 lead TQFP/QFN
AT32UC3B0128
128 Kbytes
32 Kbytes
3
1
8
2
Mini-Host + Device
64 lead TQFP/QFN
AT32UC3B064
64 Kbytes
16 Kbytes
3
1
8
2
Mini-Host + Device
64 lead TQFP/QFN
AT32UC3B1256
256 Kbytes
32 Kbytes
2
0
6
1
Device
48 lead TQFP/QFN
AT32UC3B1128
128 Kbytes
32 Kbytes
2
0
6
1
Device
48 lead TQFP/QFN
AT32UC3B164
64 Kbytes
16 Kbytes
2
0
6
1
Device
48 lead TQFP/QFN
3
32059ES–AVR32–12/07
AT32UC3B
3. Blockdiagram
Figure 3-1.
Block diagram
JTAG
INTERFACE
NEXUS
CLASS 2+
OCD
MCKO
MDO[5..0]
MSEO[1..0]
EVTI_N
EVTO_N
VBUS
D+
DID
VBOF
M
USB
INTERFACE
MEMORY PROTECTION UNIT
INSTR
INTERFACE
DATA
INTERFACE
M
M
S
CONFIGURATION
PB
S
HSB-PB
BRIDGE B
GENERAL PURPOSE IOs
256 KB
FLASH
REGISTERS BUS
HSB
PERIPHERAL
DMA
CONTROLLER
HSB-PB
BRIDGE A
PB
XIN0
XOUT0
XIN1
XOUT1
32 KHz
OSC
CLOCK
GENERATOR
OSC0
OSC1
PLL0
SERIAL
PERIPHERAL
INTERFACE
SYNCHRONOUS
SERIAL
CONTROLLER
TWO-WIRE
INTERFACE
PULSE WIDTH
MODULATION
CONTROLLER
ANALOG TO
DIGITAL
CONVERTER
RXD
TXD
CLK
RTS, CTS
DSR, DTR, DCD, RI
RXD
TXD
CLK
RTS, CTS
SCK
MISO, MOSI
NPCS[3..0]
TX_CLOCK, TX_FRAME_SYNC
TX_DATA
RX_CLOCK, RX_FRAME_SYNC
RX_DATA
SCL
GENERAL PURPOSE IOs
XIN32
XOUT32
POWER
MANAGER
PDC
115 kHz
RCOSC
PDC
WATCHDOG
TIMER
USART0
USART2
PDC
REAL TIME
COUNTER
USART1
PDC
EXTERNAL
INTERRUPT
CONTROLLER
PDC
EXTINT[7..0]
KPS[7..0]
NMI_N
PDC
INTERRUPT
CONTROLLER
PDC
PA
PB
32 KB
SRAM
M
S
HS
B
FAST GPIO
S
HIGH SPEED
BUS MATRIX
S
M
DMA
UC CPU
LOCAL BUS
INTERFACE
FLASH
CONTROLLER
TDO
TDI
TMS
MEMORY INTERFACE
TCK
PA
PB
SDA
CLOCK
CONTROLLER
SLEEP
CONTROLLER
PWM[6..0]
PLL1
GCLK[3..0]
RESET_N
A[2..0]
B[2..0]
CLK[2..0]
RESET
CONTROLLER
AD[7..0]
ADVREF
TIMER/COUNTER
4
32059ES–AVR32–12/07
AT32UC3B
3.1
3.1.1
Processor and architecture
AVR32UC CPU
• 32-bit load/store AVR32A RISC architecture.
–
–
–
–
–
15 general-purpose 32-bit registers.
32-bit Stack Pointer, Program Counter and Link Register reside in register file.
Fully orthogonal instruction set.
Privileged and unprivileged modes enabling efficient and secure Operating Systems.
Innovative instruction set together with variable instruction length ensuring industry leading
code density.
– DSP extention with saturating arithmetic, and a wide variety of multiply instructions.
• 3 stage pipeline allows one instruction per clock cycle for most instructions.
– Byte, half-word, word and double word memory access.
– Multiple interrupt priority levels.
• MPU allows for operating systems with memory protection.
3.1.2
Debug and Test system
• IEEE1149.1 compliant JTAG and boundary scan
• Direct memory access and programming capabilities through JTAG interface
• Extensive On-Chip Debug features in compliance with IEEE-ISTO 5001-2003 (Nexus 2.0) Class 2+
– Low-cost NanoTrace supported.
3.1.3
• Auxiliary port for high-speed trace information
• Hardware support for 6 Program and 2 data breakpoints
• Unlimited number of software breakpoints supported
• Advanced Program, Data, Ownership, and Watchpoint trace supported
Peripheral DMA Controller (PDCA)
• Transfers from/to peripheral to/from any memory space without intervention of the processor.
• Next Pointer Support, forbids strong real-time constraints on buffer management.
• 7 channels that can be dynamically attributed to
–
–
–
–
–
3.1.4
all USARTs
the Serial Synchronous Controller
the Serial Peripheral Interface
the ADC
the TWI Interface
Bus system
• High Speed Bus (HSB) matrixs
– Handles Requests from
Masters: the CPU (instruction and Data Fetch), PDCA, USBB, CPU SAB,
Slaves: the internal Flash, internal SRAM, Peripheral Bus A, Peripheral Bus B, USBB.
– Round-Robin Arbitration (three modes supported: no default master, last accessed default
master, fixed default master)
–
–
–
–
Burst Breaking with Slot Cycle Limit
One Address Decoder Provided per Master
Peripheral Bus A able to run on at divided bus speeds compared to the High Speed Bus
All modules connected to the same bus use the same clock, but the clock to each module
can be individually shut off by the Power Manager.
5
32059ES–AVR32–12/07
AT32UC3B
4. Package and Pinout
The device pins are multiplexed with peripheral functions as described in ”Peripheral Multiplexing on I/O lines” on page 24.
Figure 4-1.
QFP64 Pinout
47
32
48
31
64
16
1
Table 4-1.
15
QFP64 Package Pinout
1
GND
17
GND
33
PA13
49
GND
2
TCK
18
ADVREF
34
PA14
50
DP
3
TDI
19
VDDANA
35
PA15
51
DM
4
TDO
20
VDDOUT
36
PA16
52
VBUS
5
TMS
21
VDDIN
37
PA17
53
VDDPLL
6
PB00
22
VDDCORE
38
PB06
54
PB08
7
PB01
23
GND
39
PA18
55
PB09
8
VDDCORE
24
PB02
40
PA19
56
VDDCORE
9
PA03
25
PB03
41
PA28
57
PB10
10
PA04
26
PB04
42
PA29
58
PB11
11
PA05
27
PB05
43
PB07
59
PA24
12
PA06
28
PA09
44
PA20
60
PA25
13
PA07
29
PA10
45
PA21
61
PA26
14
PA08
30
PA11
46
PA22
62
PA27
15
PA30
31
PA12
47
PA23
63
RESET_N
16
PA31
32
VDDIO
48
VDDIO
64
VDDIO
6
32059ES–AVR32–12/07
AT32UC3B
Figure 4-2.
QFP48 Pinout
36
25
37
24
48
13
1
Table 4-2.
12
QFP48 Package Pinout
1
GND
13
GND
25
PA13
37
GND
2
TCK
14
ADVREF
26
PA14
38
DP
3
TDI
15
VDDANA
27
PA15
39
DM
4
TDO
16
VDDOUT
28
PA16
40
VBUS
5
TMS
17
VDDIN
29
PA17
41
VDDPLL
6
VDDCORE
18
VDDCORE
30
PA18
42
VDDCORE
7
PA03
19
GND
31
PA19
43
PA24
8
PA04
20
PA09
32
PA20
44
PA25
9
PA05
21
PA10
33
PA21
45
PA26
10
PA06
22
PA11
34
PA22
46
PA27
11
PA07
23
PA12
35
PA23
47
RESET_N
12
PA08
24
VDDIO
36
VDDIO
48
VDDIO
7
32059ES–AVR32–12/07
AT32UC3B
5. Signals Description
The following table gives details on the signal name classified by peripheral
The signals are multiplexed with GPIO pins as described in ”Peripheral Multiplexing on I/O lines”
on page 24.
Table 5-1.
Signal Description List
Signal Name
Function
Type
Active
Level
Comments
Power
VDDPLL
PLL Power Supply
Power
Input
1.65V to 1.95 V
VDDCORE
Core Power Supply
Power
Input
1.65V to 1.95 V
VDDIO
I/O Power Supply
Power
Input
3.0V to 3.6V
VDDANA
Analog Power Supply
Power
Input
3.0V to 3.6V
VDDIN
Voltage Regulator Input Supply
Power
Input
3.0V to 3.6V
VDDOUT
Voltage Regulator Output
Power
Output
1.65V to 1.95 V
GNDANA
Analog Ground
Ground
GND
Ground
Ground
Clocks, Oscillators, and PLL’s
XIN0, XIN1, XIN32
Crystal 0, 1, 32 Input
Analog
XOUT0, XOUT1,
XOUT32
Crystal 0, 1, 32 Output
Analog
JTAG
TCK
Test Clock
Input
TDI
Test Data In
Input
TDO
Test Data Out
TMS
Test Mode Select
Output
Input
Auxiliary Port - AUX
MCKO
Trace Data Output Clock
Output
MDO0 - MDO5
Trace Data Output
Output
8
32059ES–AVR32–12/07
AT32UC3B
Table 5-1.
Signal Description List
Type
Active
Level
Signal Name
Function
MSEO0 - MSEO1
Trace Frame Control
Output
EVTI_N
Event In
Output
Low
EVTO_N
Event Out
Output
Low
Comments
Power Manager - PM
GCLK0 - GCLK2
Generic Clock Pins
RESET_N
Reset Pin
Output
Input
Low
External Interrupt Module - EIM
EXTINT0 - EXTINT7
External Interrupt Pins
Input
KPS0 - KPS7
Keypad Scan Pins
NMI_N
Non-Maskable Interrupt Pin
Output
Input
Low
General Purpose I/O pin- GPIOA, GPIOB
PA0 - PA31
Parallel I/O Controller GPIOA
I/O
PB0 - PB11
Parallel I/O Controller GPIOB
I/O
Serial Peripheral Interface - SPI0
MISO
Master In Slave Out
I/O
MOSI
Master Out Slave In
I/O
NPCS0 - NPCS3
SPI Peripheral Chip Select
I/O
SCK
Clock
Low
Output
Synchronous Serial Controller - SSC
RX_CLOCK
SSC Receive Clock
I/O
RX_DATA
SSC Receive Data
Input
RX_FRAME_SYNC
SSC Receive Frame Sync
I/O
TX_CLOCK
SSC Transmit Clock
I/O
TX_DATA
SSC Transmit Data
Output
TX_FRAME_SYNC
SSC Transmit Frame Sync
I/O
Timer/Counter - TIMER
A0
Channel 0 Line A
I/O
A1
Channel 1 Line A
I/O
9
32059ES–AVR32–12/07
AT32UC3B
Table 5-1.
Signal Description List
Signal Name
Function
Type
A2
Channel 2 Line A
I/O
B0
Channel 0 Line B
I/O
B1
Channel 1 Line B
I/O
B2
Channel 2 Line B
I/O
CLK0
Channel 0 External Clock Input
Input
CLK1
Channel 1 External Clock Input
Input
CLK2
Channel 2 External Clock Input
Input
Active
Level
Comments
Two-wire Interface - TWI
SCL
Serial Clock
I/O
SDA
Serial Data
I/O
Universal Synchronous Asynchronous Receiver Transmitter - USART0, USART1, USART2
CLK
Clock
I/O
CTS
Clear To Send
DCD
Data Carrier Detect
Only USART1
DSR
Data Set Ready
Only USART1
DTR
Data Terminal Ready
Only USART1
RI
Ring Indicator
Only USART1
RTS
Request To Send
RXD
Receive Data
Input
TXD
Transmit Data
Output
Input
Output
Analog to Digital Converter - ADC
AD0 - AD7
Analog input pins
Analog
input
ADVREF
Analog positive reference voltage input
Analog
input
2.6 to 3.6V
Pulse Width Modulator - PWM
PWM0 - PWM6
PWM Output Pins
Output
Universal Serial Bus Device - USB
DDM
USB Device Port Data -
Analog
10
32059ES–AVR32–12/07
AT32UC3B
Table 5-1.
Signal Description List
Signal Name
Function
Type
DDP
USB Device Port Data +
Analog
VBUS
USB VBUS Monitor and OTG Negociation
Analog
Input
USBID
ID Pin of the USB Bus
Input
USB_VBOF
USB VBUS On/off: bus power control port
output
Active
Level
Comments
11
32059ES–AVR32–12/07
AT32UC3B
6. Power Considerations
6.1
Power Supplies
The AT32UC3B has several types of power supply pins:
•
•
•
•
•
VDDIO: Powers I/O lines. Voltage is 3.3V nominal.
VDDANA: Powers the ADC Voltage is 3.3V nominal.
VDDIN: Input voltage for the voltage regulator. Voltage is 3.3V nominal.
VDDCORE: Powers the core, memories, and peripherals. Voltage is 1.8V nominal.
VDDPLL: Powers the PLL. Voltage is 1.8V nominal.
The ground pins GND are common to VDDCORE, VDDIO and VDDPLL. The ground pin for
VDDANA is GNDANA.
Refer to ”Electrical Characteristics” on page 30 for power consumption on the various supply
pins.
The main requirement for power supplies connection is to respect a star topology for all electrical
connection.
Dual Power Supply
Single Power Supply
3.3V
3.3V
VDDAN
A
VDDI
O
VDDI
O
ADVREF
ADVREF
VDDI
N
VDDI
N
1.8V
Regulator
VDDPL
L
1.8V
Regulator
VDDOU
T
VDDOU
T
VDDCOR
E
VDDAN
A
1.8
V
VDDCOR
E
VDDPL
L
12
32059ES–AVR32–12/07
AT32UC3B
6.2
6.2.1
Voltage Regulator
Single Power Supply
The AT32UC3B embeds a voltage regulator that converts from 3.3V to 1.8V. The regulator takes
its input voltage from VDDIN, and supplies the output voltage on VDDOUT that should be externally connected to the 1.8V domains.
Adequate input supply decoupling is mandatory for VDDIN in order to improve startup stability
and reduce source voltage drop. Two input decoupling capacitors must be placed close to the
chip.
Adequate output supply decoupling is mandatory for VDDOUT to reduce ripple and avoid oscillations. The best way to achieve this is to use two capacitors in parallel between VDDOUT and
GND as close to the chip as possible
3.3V
VDDIN
CIN2
CIN1
1.8V
1.8V
Regulator
VDDOUT
COUT2
COUT1
Refer to Section 11.3 on page 32 for decoupling capacitors values and regulator characteristics.
6.2.2
Dual Power Supply
In case of dual power supply, VDDIN and VDDOUT should be connected to ground to prevent
from leakage current.
VDDIN
VDDOUT
13
32059ES–AVR32–12/07
AT32UC3B
6.3
Analog-to-Digital Converter (A.D.C) reference.
The ADC reference (ADVREF) must be provided from an external source. Two decoupling
capacitors must be used to insure proper decoupling.
3.3V
ADVREF
C
VREF2
C
VREF1
Refer to Section 11.4 on page 32 for decoupling capacitors values and electrical characteristics.
14
32059ES–AVR32–12/07
AT32UC3B
7. I/O Line Considerations
7.1
JTAG pins
TMS and TDI pins have pull-up resistors. TDO pin is an output, driven at up to VDDIO, and has
no pull-up resistor. These 3 pins can be used as GPIO-pins. At reset state, these pins are in
GPIO mode.
TCK pin cannot be used as GPIO pin. JTAG interface is enabled when TCK pin is tied low. This
pins must be pulled-up externally on application board.
7.2
RESET_N pin
The RESET_N pin is a schmitt input and integrates a permanent pull-up resistor to VDDIO. As
the product integrates a power-on reset cell, the RESET_N pin can be left unconnected in case
no reset from the system needs to be applied to the product.
7.3
TWI pins
When these pins are used for TWI, the pins are open-drain outputs with slew-rate limitation and
inputs with inputs with spike-filtering. When used as GPIO-pins or used for other peripherals, the
pins have the same characteristics as PIO pins.
7.4
GPIO pins
All the I/O lines integrate a pull-up resistor. Programming of this pull-up resistor is performed
independently for each I/O line through the GPIO Controllers. After reset, I/O lines default as
inputs with pull-up resistors disabled, except when indicated otherwise in the column “Reset
State” of the GPIO Controller multiplexing tables.
7.5
High drive pins
The four pins PA20, PA21, PA22, PA23 have high drive output capabilities. Refer to Figure 11.
on page 30 for electrical characteristics.
15
32059ES–AVR32–12/07
AT32UC3B
8. Memories
8.1
Embedded Memories
• Internal High-Speed Flash
– 256 KBytes (AT32UC3B0256, AT32UC3B1256)
– 128 KBytes (AT32UC3B0128, AT32UC3B1128)
– 64 KBytes (AT32UC3B064, AT32UC3B164)
- 0 Wait State Access at up to 30 MHz in Worst Case Conditions
- 1 Wait State Access at up to 60 MHz in Worst Case Conditions
- Pipelined Flash Architecture, allowing burst reads from sequential Flash locations, hiding
penalty of 1 wait state access
- Pipelined Flash Architecture typically reduces the cycle penalty of 1 wait state operation
to only 8% compared to 0 wait state operation
- 100 000 Write Cycles, 15-year Data Retention Capability
- 4 ms Page Programming Time, 8 ms Chip Erase Time
- Sector Lock Capabilities, Bootloader Protection, Security Bit
- 32 Fuses, Erased During Chip Erase
- User Page For Data To Be Preserved During Chip Erase
• Internal High-Speed SRAM, Single-cycle access at full speed
– 32KBytes (AT32UC3B0256, AT32UC3B0128, AT32UC3B1256 and AT32UC3B1128)
– 16KBytes (AT32UC3B064 and AT32UC3B164)
8.2
Physical Memory Map
The system bus is implemented as a bus matrix. All system bus addresses are fixed, and they
are never remapped in any way, not even in boot. Note that AVR32 UC CPU uses unsegmented
translation, as described in the AVR32 Architecture Manual. The 32-bit physical address space
is mapped as follows:
Table 8-1.
AT32UC3B Physical Memory Map
Device
Start Address
Size
AT32UC3B0256
AT32UC3B1256
AT32UC3B0128
AT32UC3B1128
AT32UC3B064
AT32UC3B164
Embedded SRAM
0x0000_0000
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
16 Kbytes
16 Kbytes
Embedded Flash
0x8000_0000
256 Kbytes
256 Kbytes
128 Kbytes
128 Kbytes
64 Kbytes
64 Kbytes
USB Configuration
0xD000_0000
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
HSB-PB Bridge A
0xFFFE_0000
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
64 Kbytes
HSB-PB Bridge B
0xFFFF_0000
64 Kbytes
64 Kbytes
64 kBytes
64 kBytes
64 Kbytes
64 Kbytes
Table 8-2.
Flash Memory Parameters
Part Number
Flash Size
(FLASH_PW)
Number of pages
(FLASH_P)
Page size
(FLASH_W)
AT32UC3B0256
256 Kbytes
512
128 words
AT32UC3B1256
256 Kbytes
512
128 words
AT32UC3B0128
128 Kbytes
256
128 words
16
32059ES–AVR32–12/07
AT32UC3B
Table 8-2.
8.3
Flash Memory Parameters
AT32UC3B1128
128 Kbytes
256
128 words
AT32UC3B064
64 Kbytes
128
128 words
AT32UC3B164
64 Kbytes
128
128 words
Bus Matrix Connections
Accesses to unused areas returns an error result to the master requesting such an access.
The bus matrix has the several masters and slaves. Each master has its own bus and its own
decoder, thus allowing a different memory mapping per master. The master number in the table
below can be used to index the HMATRIX control registers. For example, HMATRIX MCFG0
register is associated with the CPU Data master interface.
Table 8-3.
High Speed Bus masters
Master 0
CPU Data
Master 1
CPU Instruction
Master 2
CPU SAB
Master 3
PDCA
Master 4
USBB DMA
Each slave has its own arbiter, thus allowing a different arbitration per slave. The slave number
in the table below can be used to index the HMATRIX control registers. For example, SCFG3 is
associated with the Internal SRAM Slave Interface.
Table 8-4.
High Speed Bus slaves
Slave 0
Internal Flash
Slave 1
HSB-PB Bridge 0
Slave 2
HSB-PB Bridge 1
Slave 3
Internal SRAM
Slave 4
USBB DPRAM
17
32059ES–AVR32–12/07
AT32UC3B
Figure 8-1.
HMatrix Master / Slave Connections
HMATRIX MASTERS
CPU Data
0
CPU
Instruction
1
CPU SAB
2
PDCA
3
USBB DMA
4
Internal Flash
HSB-PB
Bridge 0
HSB-PB
Bridge 1
Internal SRAM
USBB DPRAM
HMATRIX SLAVES
0
1
2
3
4
18
32059ES–AVR32–12/07
AT32UC3B
9. Peripherals
9.1
Peripheral Address Map
Table 9-1.
Peripheral Address Mapping
Address
Peripheral Name
Bus
0xFFFE0000
USBB
USB 2.0 OTG - USBB
PBB
HMATRIX
HMATRIX Configuration Interface - HMATRIX
PBB
FLASHC
Flash controller - FLASHC
PBB
PDCA
Peripheral Direct Memory Access - PDCA
PBA
INTC
Interrupt controller - INTC
PBA
PM
Power Manager - PM
PBA
RTC
Real Time Counter - RTC
PBA
WDT
Watchdog Timer - WDT
PBA
EIC
External Interrupt Controller - EIC
PBA
General Purpose Input/Output - GPIO
PBA
USART0
Universal Synchronous Asynchronous Receiver
Transmitter - USART0
PBA
USART1
Universal Synchronous Asynchronous Receiver
Transmitter - USART1
PBA
USART2
Universal Synchronous Asynchronous Receiver
Transmitter - USART2
PBA
SPI
Serial Peripheral Interface - SPI
PBA
TWI
Two-wire Interface - TWI
PBA
PWM
Pulse Width Modulation Controller - PWM
PBA
SSC
Synchronous Serial Controller - SSC
PBA
0xFFFE1000
0xFFFE1400
0xFFFF0000
0xFFFF0800
0xFFFF0C00
0xFFFF0D00
0xFFFF0D30
0xFFFF0D80
0xFFFF1000
GPIO
0xFFFF1400
0xFFFF1800
0xFFFF1C00
0xFFFF2400
0xFFFF2C00
0xFFFF3000
0xFFFF3400
19
32059ES–AVR32–12/07
AT32UC3B
Table 9-1.
Peripheral Address Mapping
0xFFFF3800
TC
Timer/Counter - TC
PBA
Analog to Digital Converter - ADC
PBA
0xFFFF3C00
ADC
9.2
CPU Local Bus Mapping
Some of the registers in the GPIO module are mapped onto the CPU local bus, in addition to
being mapped on the Peripheral Bus. These registers can therefore be reached both by
accesses on the Peripheral Bus, and by accesses on the local bus.
Mapping these registers on the local bus allows cycle-deterministic toggling of GPIO pins since
the CPU and GPIO are the only modules connected to this bus. Also, since the local bus runs at
CPU speed, one write or read operation can be performed per clock cycle to the local busmapped GPIO registers.
The following GPIO registers are mapped on the local bus:
Table 9-2.
Local bus mapped GPIO registers
Port
Register
Mode
Local Bus
Address
Access
A
Output Driver Enable Register (ODER)
WRITE
0x4000_0040
Write-only
SET
0x4000_0044
Write-only
CLEAR
0x4000_0048
Write-only
TOGGLE
0x4000_004C
Write-only
WRITE
0x4000_0050
Write-only
SET
0x4000_0054
Write-only
CLEAR
0x4000_0058
Write-only
TOGGLE
0x4000_005C
Write-only
Pin Value Register (PVR)
-
0x4000_0060
Read-only
Output Driver Enable Register (ODER)
WRITE
0x4000_0140
Write-only
SET
0x4000_0144
Write-only
CLEAR
0x4000_0148
Write-only
TOGGLE
0x4000_014C
Write-only
WRITE
0x4000_0150
Write-only
SET
0x4000_0154
Write-only
CLEAR
0x4000_0158
Write-only
TOGGLE
0x4000_015C
Write-only
-
0x4000_0160
Read-only
Output Value Register (OVR)
B
Output Value Register (OVR)
Pin Value Register (PVR)
9.3
Interrupt Request Signal Map
The various modules may output Interrupt request signals. These signals are routed to the Interrupt Controller (INTC), described in a later chapter. The Interrupt Controller supports up to 64
20
32059ES–AVR32–12/07
AT32UC3B
groups of interrupt requests. Each group can have up to 32 interrupt request signals. All interrupt
signals in the same group share the same autovector address and priority level. Refer to the
documentation for the individual submodules for a description of the semantic of the different
interrupt requests.
The interrupt request signals are connected to the INTC as follows.
Table 9-3.
Interrupt Request Signal Map
Group
Line
Module
Signal
0
0
AVR32 UC CPU with optional MPU and
optional OCD
0
External Interrupt Controller
EIC 0
1
External Interrupt Controller
EIC 1
2
External Interrupt Controller
EIC 2
3
External Interrupt Controller
EIC 3
4
External Interrupt Controller
EIC 4
5
External Interrupt Controller
EIC 5
6
External Interrupt Controller
EIC 6
7
External Interrupt Controller
EIC 7
8
Real Time Counter
RTC
9
Power Manager
PM
0
General Purpose Input/Output
GPIO 0
1
General Purpose Input/Output
GPIO 1
2
General Purpose Input/Output
GPIO 2
3
General Purpose Input/Output
GPIO 3
4
General Purpose Input/Output
GPIO 4
5
General Purpose Input/Output
GPIO 5
0
Peripheral Direct Memory Access
PDCA 0
1
Peripheral Direct Memory Access
PDCA 1
2
Peripheral Direct Memory Access
PDCA 2
3
Peripheral Direct Memory Access
PDCA 3
4
Peripheral Direct Memory Access
PDCA 4
5
Peripheral Direct Memory Access
PDCA 5
6
Peripheral Direct Memory Access
PDCA 6
4
0
Flash controller
FLASHC
5
0
Universal Synchronous Asynchronous
Receiver Transmitter
USART0
6
0
Universal Synchronous Asynchronous
Receiver Transmitter
USART1
7
0
Universal Synchronous Asynchronous
Receiver Transmitter
USART2
SYSBLOCK
COMPARE
1
2
3
21
32059ES–AVR32–12/07
AT32UC3B
Table 9-3.
Interrupt Request Signal Map
9
0
Serial Peripheral Interface
SPI
11
0
Two-wire Interface
TWI
12
0
Pulse Width Modulation Controller
PWM
13
0
Synchronous Serial Controller
SSC
0
Timer/Counter
TC0
1
Timer/Counter
TC1
2
Timer/Counter
TC2
15
0
Analog to Digital Converter
ADC
17
0
USB 2.0 OTG
14
9.4
9.4.1
USBB
Clock Connections
Timer/Counters
Each Timer/Counter channel can independently select an internal or external clock source for its
counter:
Table 9-4.
Timer/Counter clock connections
Source
Name
Connection
Internal
TIMER_CLOCK1
Slow Clock (Internal RC oscillator)
TIMER_CLOCK2
PBA Clock / 2
TIMER_CLOCK3
PBA Clock / 8
TIMER_CLOCK4
PBA Clock / 32
TIMER_CLOCK5
PBA Clock / 128
XC0
See Section 9.8
External
XC1
XC2
9.4.2
USARTs
Each USART can be connected to an internally divided clock:
Table 9-5.
USART clock connections
USART
Source
Name
Connection
0
Internal
CLK_DIV
PBA Clock / 8
1
2
22
32059ES–AVR32–12/07
AT32UC3B
9.4.3
SPIs
SPI can be connected to an internally divided clock:
Table 9-6.
9.5
SPI clock connections
SPI
Source
Name
Connection
0
Internal
CLK_DIV
PBA clock or
PBA clock / 32
Nexus OCD AUX port connections
If the OCD trace system is enabled, the trace system will take control over a number of pins, irrespectively of the PIO configuration. Two different OCD trace pin mappings are possible,
depending on the configuration of the OCD AXS register. For details, see the AVR32 UCTechnical Reference Manual.
Table 9-7.
9.6
Nexus OCD AUX port connections
Pin
AXS=0
AXS=1
EVTI_N
PB05
PA14
MDO[5]
PB04
PA08
MDO[4]
PB03
PA07
MDO[3]
PB02
PA06
MDO[2]
PB01
PA05
MDO[1]
PB00
PA03
MDO[0]
PA31
PA02
EVTO_N
PA15
PA15
MCKO
PA30
PA13
MSEO[1]
PB06
PA09
MSEO[0]
PB07
PA10
DMA handshake signals
The PDCA and the peripheral modules communicate through a set of handshake signals. The
following table defines the valid settings for the Peripheral Identifier (PID) in the PDCA Peripheral Select Register (PSR).
Table 9-8.
PDCA Handshake Signals
PID Value
Peripheral module & direction
0
ADC
1
SSC - RX
2
USART0 - RX
3
USART1 - RX
4
USART2 - RX
23
32059ES–AVR32–12/07
AT32UC3B
Table 9-8.
9.7
PDCA Handshake Signals
PID Value
Peripheral module & direction
5
TWI - RX
6
SPI0 - RX
7
SSC - TX
8
USART0 - TX
9
USART1 - TX
10
USART2 - TX
11
TWI - TX
12
SPI0 - TX
High Drive Current GPIO
Ones of GPIOs can be used to drive twice current than other GPIO capability (see Electrical
Characteristics chapter). The list of those GPIOs is shown in Table 9-9.
Table 9-9.
High Drive Current GPIO
GPIO Name
GPIO/0/P21
GPIO/0/P22
GPIO/0/P23
GPIO/0/P24
9.8
Peripheral Multiplexing on I/O lines
Each GPIO line can be assigned to one of 3 peripheral functions; A, B or C. The following table
define how the I/O lines on the peripherals A, B and C are multiplexed by the GPIO.
Table 9-10.
GPIO Controller Function Multiplexing
QFP48
QFP64
PIN
GPIO Pin
Function A
Function B
Function C
7
9
PA03
GPIO 3
ADC - AD[0]
PM - GCLK[0]
USBB - USB_ID
8
10
PA04
GPIO 4
ADC - AD[1]
PM - GCLK[1]
USBB - USB_VBOF
9
11
PA05
GPIO 5
EIC - EXTINT[0]
ADC - AD[2]
USART1 - DCD
10
12
PA06
GPIO 6
EIC - EXTINT[1]
ADC - AD[3]
USART1 - DSR
11
13
PA07
GPIO 7
PWM - PWM[0]
ADC - AD[4]
USART1 - DTR
12
14
PA08
GPIO 8
PWM - PWM[1]
ADC - AD[5]
USART1 - RI
20
28
PA09
GPIO 9
TWI - SCL
SPI - NPCS[2]
USART1 - CTS
21
29
PA10
GPIO 10
TWI - SDA
SPI - NPCS[3]
USART1 - RTS
22
30
PA11
GPIO 11
USART0 - RTS
TC - A2
PWM - PWM[0]
23
31
PA12
GPIO 12
USART0 - CTS
TC - B2
PWM - PWM[1]
25
33
PA13
GPIO 13
NMI
PWM - PWM[2]
USART0 - CLK
24
32059ES–AVR32–12/07
AT32UC3B
Table 9-10.
9.9
GPIO Controller Function Multiplexing
26
34
PA14
GPIO 14
SPI - MOSI
PWM - PWM[3]
EIC - EXTINT[2]
27
35
PA15
GPIO 15
SPI - SCK
PWM - PWM[4]
USART2 - CLK
28
36
PA16
GPIO 16
SPI - NPCS[0]
TC - CLK1
29
37
PA17
GPIO 17
SPI - NPCS[1]
TC - CLK2
SPI - SCK
30
39
PA18
GPIO 18
USART0 - RXD
PWM - PWM[5]
SPI - MISO
31
40
PA19
GPIO 19
USART0 - TXD
PWM - PWM[6]
SPI - MOSI
32
44
PA20
GPIO 20
USART1 - CLK
TC - CLK0
USART2 - RXD
33
45
PA21
GPIO 21
PWM - PWM[2]
TC - A1
USART2 - TXD
34
46
PA22
GPIO 22
PWM - PWM[6]
TC - B1
ADC - TRIGGER
35
47
PA23
GPIO 23
USART1 - TXD
SPI - NPCS[1]
EIC - EXTINT[3]
43
59
PA24
GPIO 24
USART1 - RXD
SPI - NPCS[0]
EIC - EXTINT[4]
44
60
PA25
GPIO 25
SPI - MISO
PWM - PWM[3]
EIC - EXTINT[5]
45
61
PA26
GPIO 26
USBB - USB_ID
USART2 - TXD
TC - A0
46
62
PA27
GPIO 27
USBB - USB_VBOF
USART2 - RXD
TC - B0
41
PA28
GPIO 28
USART0 - CLK
PWM - PWM[4]
SPI - MISO
42
PA29
GPIO 29
TC - CLK0
TC - CLK1
SPI - MOSI
15
PA30
GPIO 30
ADC - AD[6]
EIC - SCAN[0]
PM - GCLK[2]
16
PA31
GPIO 31
ADC - AD[7]
EIC - SCAN[1]
6
PB00
GPIO 32
TC - A0
EIC - SCAN[2]
USART2 - CTS
7
PB01
GPIO 33
TC - B0
EIC - SCAN[3]
USART2 - RTS
24
PB02
GPIO 34
EIC - EXTINT[6]
TC - A1
USART1 - TXD
25
PB03
GPIO 35
EIC - EXTINT[7]
TC - B1
USART1 - RXD
26
PB04
GPIO 36
USART1 - CTS
SPI - NPCS[3]
TC - CLK2
27
PB05
GPIO 37
USART1 - RTS
SPI - NPCS[2]
PWM - PWM[5]
38
PB06
GPIO 38
SSC - RX_CLOCK
USART1 - DCD
EIC - SCAN[4]
43
PB07
GPIO 39
SSC - RX_DATA
USART1 - DSR
EIC - SCAN[5]
54
PB08
GPIO 40
SSC RX_FRAME_SYNC
USART1 - DTR
EIC - SCAN[6]
55
PB09
GPIO 41
SSC - TX_CLOCK
USART1 - RI
EIC - SCAN[7]
57
PB10
GPIO 42
SSC - TX_DATA
TC - A2
USART0 - RXD
58
PB11
GPIO 43
SSC TX_FRAME_SYNC
TC - B2
USART0 - TXD
3
3
TDI
GPIO 0
4
4
TDO
GPIO 1
5
5
TMS
GPIO 2
Oscillator Pinout
The oscillators are not mapped to the normal A,B or C functions and their muxings are controlled
by registers in the Power Manager (PM). Please refer to the power manager chapter for more
information about this.
25
32059ES–AVR32–12/07
AT32UC3B
Table 9-11.
QFP48 pin
QFP64 pin
Pad
Oscillator pin
30
39
PA18
xin0
41
PA28
xin1
22
30
PA11
xin32
31
40
PA19
xout0
42
PA29
xout1
31
PA12
xout32
23
9.10
Oscillator pinout
Peripheral overview
9.10.1
USB Controller
9.10.2
• USB 2.0 Compliant, Full-/Low-Speed (FS/LS) and On-The-Go (OTG), 12 Mbit/s
• 7 Pipes/Endpoints
• 960 bytes of Embedded Dual-Port RAM (DPRAM) for Pipes/Endpoints
• Up to 2 Memory Banks per Pipe/Endpoint (Not for Control Pipe/Endpoint)
• Flexible Pipe/Endpoint Configuration and Management with Dedicated DMA Channels
• On-Chip Transceivers Including Pull-Ups
• System wake-up on USB line activity
Serial Peripheral Interface
• Supports communication with serial external devices
– Four chip selects with external decoder support allow communication with up to 15
peripherals
– Serial memories, such as DataFlash and 3-wire EEPROMs
– Serial peripherals, such as ADCs, DACs, LCD Controllers, CAN Controllers and Sensors
– External co-processors
• Master or slave serial peripheral bus interface
– 8- to 16-bit programmable data length per chip select
– Programmable phase and polarity per chip select
– Programmable transfer delays between consecutive transfers and between clock and data
per chip select
– Programmable delay between consecutive transfers
– Selectable mode fault detection
• Very fast transfers supported
– Transfers with baud rates up to Peripheral Bus A (PBA) max frequency
– The chip select line may be left active to speed up transfers on the same device
26
32059ES–AVR32–12/07
AT32UC3B
9.10.3
Two-wire Interface
•
•
•
•
9.10.4
High speed up to 400kbit/s
Compatibility with standard two-wire serial memory
One, two or three bytes for slave address
Sequential read/write operations
USART
• Programmable Baud Rate Generator
• 5- to 9-bit full-duplex synchronous or asynchronous serial communications
•
•
•
•
•
•
9.10.5
– 1, 1.5 or 2 stop bits in Asynchronous Mode or 1 or 2 stop bits in Synchronous Mode
– Parity generation and error detection
– Framing error detection, overrun error detection
– MSB- or LSB-first
– Optional break generation and detection
– By 8 or by-16 over-sampling receiver frequency
– Hardware handshaking RTS-CTS
– Receiver time-out and transmitter timeguard
– Optional Multi-drop Mode with address generation and detection
– Optional Manchester Encoding
RS485 with driver control signal
ISO7816, T = 0 or T = 1 Protocols for interfacing with smart cards
– NACK handling, error counter with repetition and iteration limit
IrDA modulation and demodulation
– Communication at up to 115.2 Kbps
Test Modes
– Remote Loopback, Local Loopback, Automatic Echo
SPI Mode
– Master or Slave
– Serial Clock Programmable Phase and Polarity
– SPI Serial Clock (SCK) Frequency up to Internal Clock Frequency PBA/4
Supports Connection of Two Peripheral DMA Controller Channels (PDC)
– Offers Buffer Transfer without Processor Intervention
Serial Synchronous Controller
• Provides serial synchronous communication links used in audio and telecom applications (with
CODECs in Master or Slave Modes, I2S, TDM Buses, Magnetic Card Reader, etc.)
• Contains an independent receiver and transmitter and a common clock divider
• Offers a configurable frame sync and data length
• Receiver and transmitter can be programmed to start automatically or on detection of different
event on the frame sync signal
• Receiver and transmitter include a data signal, a clock signal and a frame synchronization signal
9.10.6
Timer Counter
• Three 16-bit Timer Counter Channels
• Wide range of functions including:
–
–
–
–
–
Frequency Measurement
Event Counting
Interval Measurement
Pulse Generation
Delay Timing
27
32059ES–AVR32–12/07
AT32UC3B
– Pulse Width Modulation
– Up/down Capabilities
• Each channel is user-configurable and contains:
– Three external clock inputs
– Five internal clock inputs
– Two multi-purpose input/output signals
• Two global registers that act on all three TC Channels
9.10.7
Pulse Width Modulation Controller
• 7 channels, one 16-bit counter per channel
• Common clock generator, providing Thirteen Different Clocks
– A Modulo n counter providing eleven clocks
– Two independent Linear Dividers working on modulo n counter outputs
• Independent channel programming
– Independent Enable Disable Commands
– Independent Clock
– Independent Period and Duty Cycle, with Double Bufferization
– Programmable selection of the output waveform polarity
– Programmable center or left aligned output waveform
28
32059ES–AVR32–12/07
AT32UC3B
10. Boot Sequence
This chapter summarizes the boot sequence of the AT32UC3B. The behaviour after power-up is
controlled by the Power Manager. For specific details, refer to Section 13. ”Power Manager
(PM)” on page 45.
10.1
Starting of clocks
After power-up, the device will be held in a reset state by the Power-On Reset circuitry, until the
power has stabilized throughout the device. Once the power has stabilized, the device will use
the internal RC Oscillator as clock source.
On system start-up, the PLLs are disabled. All clocks to all modules are running. No clocks have
a divided frequency, all parts of the system recieves a clock with the same frequency as the
internal RC Oscillator.
10.2
Fetching of initial instructions
After reset has been released, the AVR32 UC CPU starts fetching instructions from the reset
address, which is 0x8000_0000. This address points to the first address in the internal Flash.
The code read from the internal Flash is free to configure the system to use for example the
PLLs, to divide the frequency of the clock routed to some of the peripherals, and to gate the
clocks to unused peripherals.
29
32059ES–AVR32–12/07
AT32UC3B
11. Electrical Characteristics
11.1
Absolute Maximum Ratings*
Operating Temperature.................................... -40°C to +85°C
Storage Temperature ..................................... -60°C to +150°C
Voltage on GPIO Pins
with respect to Ground ............................................. -0.3 to 5V
Maximum Voltage on RESET_N Pin ................................ 3.3V
Maximum Operating Voltage (VDDCORE, VDDPLL) ..... 1.95V
*NOTICE:
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability.
Maximum Operating Voltage (VDDIO).............................. 3.6V
Total DC Output Current on all I/O Pin
for 48-pin package ....................................................... 200 mA
for 64-pin package ....................................................... 265 mA
30
32059ES–AVR32–12/07
AT32UC3B
11.2
DC Characteristics
The following characteristics are applicable to the operating temperature range: TA = -40°C to 85°C, unless otherwise specified and are certified for a junction temperature up to TJ = 100°C.
Symbol
Parameter
VVDDCOR
DC Supply Core
VVDDPLL
Condition
Min.
Typ.
Max.
Units
1.65
1.95
V
DC Supply PLL
1.65
1.95
V
VVDDIO
DC Supply Peripheral I/Os
3.0
3.6
V
VREF
Analog reference voltage
2.6
3.6
V
VIL
Input Low-level Voltage
-0.3
+0.8
V
VIH
Input High-level Voltage
2.0
VVDDIO+0.
3
V
VOL
Output Low-level Voltage
0.4
V
VOH
Output High-level Voltage
VVDDIO= VVDDIOM or VVDDIOP
ILEAK
Input Leakage Current
Pullup resistors disabled
TBD
µA
CIN
Input Capacitance
TBD
pF
RPULLUP
Pull-up Resistance
IO
I/O Output Current
4
mA
E
ISC
ISCR
Static Current
Static Current of internal
regulator
VVDDIO-0.4
TBD
On VVDDCORE = 1.8V,
device in static mode
TA
=25°C
6
µA
All inputs driven
including JTAG;
RESET_N=1
TA
=85°C
25
µA
Low Power mode
(stop, deep stop or
static
TA
=25°C
10
µA
31
32059ES–AVR32–12/07
AT32UC3B
11.3
Regulator characteristics
11.3.1
Electrical characteristics
Symbol
Parameter
VVDDIN
VVDDOUT
IOUT
11.3.2
Condition
Min.
Typ.
Max.
Units
Supply voltage (input)
2.7
3.3
3.6
V
Supply voltage (output)
1.81
1.85
1.89
V
Maximum DC output current with VVDDIN = 3.3V
100
mA
Maximum DC output current with VVDDIN = 2.7V
90
mA
Decoupling requirements
Symbol
Parameter
CIN1
Typ.
Techno.
Units
Input Regulator Capacitor 1
1
NPO
nF
CIN2
Input Regulator Capacitor 2
4.7
X7R
uF
COUT1
Output Regulator Capacitor 1
470
NPO
pF
COUT2
Output Regulator Capacitor 2
2.2
X7R
uF
11.4
Condition
Analog characteristics
11.4.1
Electrical characteristics
Symbol
Parameter
VADVREF
Analog voltage reference (input)
11.4.2
Min.
Typ.
2.6
Max.
Units
3.6
V
Decoupling requirements
Symbol
Parameter
CVREF1
CVREF2
11.4.3
Condition
Condition
Typ.
Techno.
Units
Voltage reference Capacitor 1
10
-
nF
Voltage reference Capacitor 2
1
-
uF
BOD
Table 11-1.
BODLEVEL Values
BODLEVEL Value
Typ.
Units.
000000b
1.58
V
010111b
1.62
V
011111b
1.67
V
100111b
1.77
V
111111b
1.92
V
The values in Table 11-1 describes the values of the BODLEVEL in the flash General Purpose
Fuse register.
32
32059ES–AVR32–12/07
AT32UC3B
11.5
Power Consumption
The values in Table 11-2 and Table 11-3 on page 34 are measured values of power consumption with operating conditions as follows:
•VDDIO = 3.3V
•VDDCORE = VDDPLL = 1.8V
•TA = 25°C, TA = 85°C
•I/Os are inactive
Figure 11-1. Measure schematic
VDDANA
VDDIO
Amp0
VDDIN
Internal
Voltage
Regulator
VDDOUT
Amp2
VDDCORE
VDDPLL
33
32059ES–AVR32–12/07
AT32UC3B
These figures represent the power consumption measured on the power supplies.
Table 11-2.
Power Consumption for Different Modes(1)
Mode
Conditions
Active
CPU running from flash.
CPU clocked from PLL0 at f MHz
Voltage regulator is on.
XIN0 : external clock. (1)
XIN1 stopped. XIN32 stopped
PLL0 running
All peripheral clocks activated.
GPIOs on internal pull-up.
JTAG unconnected with ext pull-up.
Typ : Ta = 25 °C
CPU is in static mode
GPIOs on internal pull-up.
All peripheral clocks de-activated.
DM and DP pins connected to ground.
XIN0,Xin1 and XIN2 are stopped
Static
Consumption
Typ.
Unit
f = 12 MHz
5.5
mA
f = 24 MHz
10
mA
f = 36MHz
14.5
mA
f = 50 MHz
19.5
mA
f = 60 MHz
23.5
mA
on Amp0
15.5
uA
on Amp1
6
uA
1. Core frequency is generated from XIN0 using the PLL so that 140 MHz < fpll0 < 160 MHz and
10 MHz < fxin0 < 12MHz.
Table 11-3.
Peripheral
Power Consumption by Peripheral in Active Mode
Consumption
INTC
20
GPIO
27
PDCA
27
USART
35
USB
30
ADC
18
TWI
14
PWM
26
SPI
11
SSC
35
TC
26
Unit
µA/MHz
34
32059ES–AVR32–12/07
AT32UC3B
11.6
Clock Characteristics
These parameters are given in the following conditions:
• VDDCORE = 1.8V
• Ambient Temperature = 25°C
11.6.1
CPU/HSB Clock Characteristics
Table 11-4.
Core Clock Waveform Parameters
Symbol
Parameter
1/(tCPCPU)
CPU Clock Frequency
tCPCPU
CPU Clock Period
11.6.2
Conditions
Min
Max
Units
60
MHz
16.6
ns
PBA Clock Characteristics
Table 11-5.
PBA Clock Waveform Parameters
Symbol
Parameter
1/(tCPPBA)
PBA Clock Frequency
tCPPBA
PBA Clock Period
11.6.3
Conditions
Min
Max
Units
60
MHz
16.6
ns
PBB Clock Characteristics
Table 11-6.
PBB Clock Waveform Parameters
Symbol
Parameter
1/(tCPPBB)
PBB Clock Frequency
tCPPBB
PBB Clock Period
11.6.4
Conditions
Min
Max
Units
60
MHz
16.6
ns
XIN Clock Characteristics
Table 11-7.
XIN Clock Electrical Characteristics
Symbol
Parameter
1/(tCPXIN)
XIN Clock Frequency
tCPXIN
XIN Clock Period
tCHXIN
XIN Clock High Half-period
0.4 x tCPXIN
0.6 x tCPXIN
tCLXIN
XIN Clock Low Half-period
0.4 x tCPXIN
0.6 x tCPXIN
CIN
XIN Input Capacitance
(1)
RIN
XIN Pulldown Resistor
(1)
Note:
Conditions
Min
Max
3
Units
24
41.0
MHz
ns
12
pF
TBD
kΩ
1. These characteristics apply only when the Main Oscillator is in bypass mode.
35
32059ES–AVR32–12/07
AT32UC3B
11.6.5
RESET_N Characteristics
Table 11-8.
RESET_N Clock Waveform Parameters
Symbol
Parameter
tRESET
RESET_N minimum pulse length
Conditions
Min
10
Max
Units
ns
36
32059ES–AVR32–12/07
AT32UC3B
11.7
Crystal Oscillator Characteristis
The following characteristics are applicable to the operating temperature range: TA = -40°C to 85°C and worst case of
power supply, unless otherwise specified.
11.7.1
32 KHz Oscillator Characteristics
Table 11-9.
32 KHz Oscillator Characteristics
Symbol
Parameter
1/(tCP32KHz)
Crystal Oscillator Frequency
Conditions
Min
Max
Unit
32 768
Hz
60
%
12.5
pF
600
1200
ms
Active mode
1.8
µA
Standby mode
0.1
µA
Max
Unit
16
MHz
Duty Cycle
40
CL
Equivalent Load Capacitance
6
tST
Startup Time
IOSC
Current Consumption
Note:
Typ
50
CL = 6pF(1)
CL = 12.5pF(1)
1. CL is the equivalent load capacitance.
11.7.2
Main Oscillators Characteristics
Table 11-10. Main Oscillator Characteristics
Symbol
Parameter
Conditions
1/(tCPMAIN)
Crystal Oscillator Frequency
CL1, CL2
Internal Load Capacitance
(CL1 = CL2)
12
pF
CL
Equivalent Load Capacitance
6
pF
IOSC
Startup Time
Current Consumption
Typ
3
Duty Cycle
tST
Min
40
50
@3MHz
@8MHz
@16MHz
@20MHz
60
%
14.5
4
1.4
1
ms
Active mode @3 MHz
Active mode @8 MHz
Active mode @16 MHz
Active mode @20 MHz
150
150
300
400
µA
Standby mode @TBD V
1
µA
37
32059ES–AVR32–12/07
AT32UC3B
11.7.3
PLL Characteristics
Table 11-11. Phase Lock Loop Characteristics
Symbol
Parameter
FOUT
Output Frequency
FIN
Input Frequency
IPLL
Current Consumption
Conditions
Active mode FVCO@96MHz
Active mode FVCO@128MHz
Active mode FVCO@160MHz
Standby mode
Min
Typ
Max
Unit
80
240
MHz
4
32
MHz
320
410
450
µA
5
µA
38
32059ES–AVR32–12/07
AT32UC3B
11.8
ADC Characteristics
Table 11-12. Channel Conversion Time and ADC Clock
Parameter
Conditions
ADC Clock Frequency
ADC Clock Frequency
Startup Time
Max
Units
10-bit resolution mode
5
MHz
8-bit resolution mode
8
MHz
Return from Idle Mode
20
µs
Track and Hold Acquisition Time
Min
Typ
600
ns
Conversion Time
ADC Clock = 5 MHz
Conversion Time
ADC Clock = 8 MHz
1.25
µs
Throughput Rate
ADC Clock = 5 MHz
384(1)
kSPS
Throughput Rate
ADC Clock = 8 MHz
533(2)
kSPS
Notes:
2
µs
1. Corresponds to 13 clock cycles at 5 MHz: 3 clock cycles for track and hold acquisition time and 10 clock cycles for
conversion.
2. Corresponds to 15 clock cycles at 8 MHz: 5 clock cycles for track and hold acquisition time and 10 clock cycles for
conversion.
Table 11-13. External Voltage Reference Input
Parameter
Conditions
ADVREF Input Voltage Range
ADVREF Average Current
Min
Typ
2.6
On 13 samples with ADC Clock = 5 MHz
200
Current Consumption on VDDANA
Max
Units
VDDANA
V
250
µA
TBD
mA
Max
Units
Table 11-14. Analog Inputs
Parameter
Min
Input Voltage Range
Typ
0
Input Leakage Current
VADVREF
TBD
Input Capacitance
µA
TBD
pF
Max
Units
Table 11-15. Transfer Characteristics
Parameter
Conditions
Min
Resolution
Typ
10
Absolute Accuracy
f=5MHz
Integral Non-linearity
f=5MHz
0.35
0.3
Bit
0.8
LSB
0.5
LSB
Differential Non-linearity
f=5MHz
0.5
LSB
Offset Error
f=5MHz
-0.5
0.5
LSB
Gain Error
f=5MHz
-0.5
0.5
LSB
39
32059ES–AVR32–12/07
AT32UC3B
11.9
JTAG/ICE Timings
11.9.1
ICE Interface Signals
Table 11-16. ICE Interface Timing Specification
Symbol
Parameter
Conditions
Min
Max
Units
ICE0
TCK Low Half-period
(1)
ICE1
TCK High Half-period
(1)
ns
ICE2
TCK Period
(1)
ns
TDI, TMS, Setup before TCK High
(1)
ns
ICE4
TDI, TMS, Hold after TCK High
(1)
ns
ICE5
TDO Hold Time
(1)
ns
TCK Low to TDO Valid
(1)
ns
ICE3
ICE6
Note:
ns
1. VVDDIO from 3.0V to 3.6V, maximum external capacitor = 40pF
Figure 11-2. ICE Interface Signals
ICE2
TCK
ICE0
ICE1
TMS/TDI
ICE3
ICE4
TDO
ICE5
ICE6
40
32059ES–AVR32–12/07
AT32UC3B
11.9.2
JTAG Interface Signals
Table 11-17. JTAG Interface Timing specification
Symbol
JTAG0
JTAG1
JTAG2
JTAG3
JTAG4
JTAG5
JTAG6
JTAG7
JTAG8
JTAG9
JTAG10
Note:
Parameter
Conditions
Min
TCK Low Half-period
(1)
Max
6
ns
TCK High Half-period
(1)
3
ns
TCK Period
(1)
9
ns
TDI, TMS Setup before TCK High
(1)
1
ns
TDI, TMS Hold after TCK High
(1)
0
ns
TDO Hold Time
(1)
4
ns
TCK Low to TDO Valid
(1)
Device Inputs Setup Time
(1)
ns
Device Inputs Hold Time
(1)
ns
Device Outputs Hold Time
(1)
ns
TCK to Device Outputs Valid
(1)
ns
6
Units
ns
1. VVDDIO from 3.0V to 3.6V, maximum external capacitor = 40pF
41
32059ES–AVR32–12/07
AT32UC3B
Figure 11-3. JTAG Interface Signals
JTAG2
TCK
JTAG
JTAG1
0
TMS/TDI
JTAG3
JTAG4
JTAG7
JTAG8
TDO
JTAG5
JTAG6
Device
Inputs
Device
Outputs
JTAG9
JTAG10
11.10 SPI Characteristics
Figure 11-4. SPI Master mode with (CPOL = NCPHA = 0) or (CPOL= NCPHA= 1)
SPCK
SPI0
SPI1
MISO
SPI2
MOSI
42
32059ES–AVR32–12/07
AT32UC3B
Figure 11-5. SPI Master mode with (CPOL=0 and NCPHA=1) or (CPOL=1 and NCPHA=0)
SPCK
SPI3
SPI4
MISO
SPI5
MOSI
Figure 11-6. SPI Slave mode with (CPOL=0 and NCPHA=1) or (CPOL=1 and NCPHA=0)
SPCK
SPI6
MISO
SPI7
SPI8
MOSI
Figure 11-7. SPI Slave mode with (CPOL = NCPHA = 0) or (CPOL= NCPHA= 1)
SPCK
SPI9
MISO
SPI10
SPI11
MOSI
43
32059ES–AVR32–12/07
AT32UC3B
Table 11-18. SPI Timings
Symbol
SPI0
Parameter
Conditions
MISO Setup time before SPCK rises (master)
SPI1
MISO Hold time after SPCK rises (master)
SPI2
SPCK rising to MOSI Delay (master)
(1)
3.3V domain
(1)
3.3V domain
3.3V domain
(1)
(1)
SPI3
MISO Setup time before SPCK falls (master)
3.3V domain
SPI4
MISO Hold time after SPCK falls (master)
3.3V domain (1)
SPI5
SPCK falling to MOSI Delay (master)
3.3V domain (1)
SPI6
SPCK falling to MISO Delay (slave)
SPI7
MOSI Setup time before SPCK rises (slave)
SPI8
MOSI Hold time after SPCK rises (slave)
SPI9
SPCK rising to MISO Delay (slave)
SPI10
MOSI Setup time before SPCK falls (slave)
SPI11
Notes:
MOSI Hold time after SPCK falls (slave)
Min
Max
(2)
22 + (tCPMCK)/2
Units
ns
0
ns
7
(2)
22 + (tCPMCK)/2
ns
ns
0
ns
7
ns
26.5
ns
3.3V domain
(1)
3.3V domain
(1)
0
ns
3.3V domain
(1)
1.5
ns
3.3V domain
(1)
3.3V domain
(1)
0
ns
3.3V domain
(1)
1
ns
27
ns
1. 3.3V domain: VVDDIO from 3.0V to 3.6V, maximum external capacitor = 40 pF.
2. tCPMCK: Master Clock period in ns.
11.11 Flash Characteristics
The following table gives the device maximum operating frequency depending on the field FWS
of the Flash FSR register. This field defines the number of wait states required to access the
Flash Memory.
Table 11-19.
Flash Wait States
FWS
Read Operations
Maximum Operating Frequency (MHz)
0
1 cycle
33
1
2 cycles
60
44
32059ES–AVR32–12/07
AT32UC3B
12. Mechanical Characteristics
12.1
12.1.1
Thermal Considerations
Thermal Data
Table 12-1 summarizes the thermal resistance data depending on the package.
Table 12-1.
12.1.2
Thermal Resistance Data
Symbol
Parameter
Condition
Package
Typ
θJA
Junction-to-ambient thermal resistance
Still Air
TQFP64
TBD
θJC
Junction-to-case thermal resistance
TQFP64
TBD
θJA
Junction-to-ambient thermal resistance
TQFP48
TBD
θJC
Junction-to-case thermal resistance
TQFP48
TBD
Still Air
Unit
°C/W
°C/W
Junction Temperature
The average chip-junction temperature, TJ, in °C can be obtained from the following:
1.
T J = T A + ( P D × θ JA )
2.
T J = T A + ( P D × ( θ HEATSINK + θ JC ) )
where:
• θJA = package thermal resistance, Junction-to-ambient (°C/W), provided in Table 12-1 on page
45.
• θJC = package thermal resistance, Junction-to-case thermal resistance (°C/W), provided in
Table 12-1 on page 45.
• θHEAT SINK = cooling device thermal resistance (°C/W), provided in the device datasheet.
• PD = device power consumption (W) estimated from data provided in the section ”Power
Consumption” on page 33.
• TA = ambient temperature (°C).
From the first equation, the user can derive the estimated lifetime of the chip and decide if a
cooling device is necessary or not. If a cooling device is to be fitted on the chip, the second
equation should be used to compute the resulting average chip-junction temperature TJ in °C.
45
32059ES–AVR32–12/07
AT32UC3B
12.2
Package Drawings
Figure 12-1. TQFP-64 package drawing
Table 12-2.
Device and Package Maximum Weight
TBD
Table 12-3.
mg
Package Characteristics
Moisture Sensitivity Level
Table 12-4.
TBD
Package Reference
JEDEC Drawing Reference
MS-026
JESD97 Classification
E3
46
32059ES–AVR32–12/07
AT32UC3B
Figure 12-2. TQFP-48 package drawing
Table 12-5.
Device and Package Maximum Weight
TBD
Table 12-6.
mg
Package Characteristics
Moisture Sensitivity Level
Table 12-7.
TBD
Package Reference
JEDEC Drawing Reference
MS-026
JESD97 Classification
E3
47
32059ES–AVR32–12/07
AT32UC3B
Figure 12-3. QFN-64 package drawing
Table 12-8.
Device and Package Maximum Weight
TBD
Table 12-9.
mg
Package Characteristics
Moisture Sensitivity Level
TBD
Table 12-10. Package Reference
JEDEC Drawing Reference
M0-220
JESD97 Classification
E3
48
32059ES–AVR32–12/07
AT32UC3B
Figure 12-4. QFN-48 package drawing
Table 12-11. Device and Package Maximum Weight
TBD
mg
Table 12-12. Package Characteristics
Moisture Sensitivity Level
TBD
Table 12-13. Package Reference
JEDEC Drawing Reference
M0-220
JESD97 Classification
E3
49
32059ES–AVR32–12/07
AT32UC3B
12.3
Soldering Profile
Table 12-14 gives the recommended soldering profile from J-STD-20.
Table 12-14. Soldering Profile
Profile Feature
Green Package
Average Ramp-up Rate (217°C to Peak)
TBD
Preheat Temperature 175°C ±25°C
TBD
Temperature Maintained Above 217°C
TBD
Time within 5°C of Actual Peak Temperature
TBD
Peak Temperature Range
TBD
Ramp-down Rate
TBD
Time 25°C to Peak Temperature
TBD
Note:
It is recommended to apply a soldering temperature higher than 250°C.
A maximum of three reflow passes is allowed per component.
50
32059ES–AVR32–12/07
AT32UC3B
13. Ordering Information
Device
AT32UC3B0256
AT32UC3B0128
AT32UC3B064
AT32UC3B1256
AT32UC3B1128
AT32UC3B164
Ordering Code
Package
Conditioning
Temperature Operating
Range
AT32UC3B0256-A2UT
TQFP 64
Tray
Industrial (-40°C to 85°C)
AT32UC3B0256-Z2UT
QFN 64
Tray
Industrial (-40°C to 85°C)
AT32UC3B0128-A2UT
TQFP 64
Tray
Industrial (-40°C to 85°C)
AT32UC3B0128-Z2UT
QFN 64
Tray
Industrial (-40°C to 85°C)
AT32UC3B064-A2UT
TQFP 64
Tray
Industrial (-40°C to 85°C)
AT32UC3B064-Z2UT
QFN 64
Tray
Industrial (-40°C to 85°C)
AT32UC3B1256-AUT
TQFP 48
Tray
Industrial (-40°C to 85°C)
AT32UC3B1256-Z1UT
QFN 48
Tray
Industrial (-40°C to 85°C)
AT32UC3B1128-AUT
TQFP 48
Tray
Industrial (-40°C to 85°C)
AT32UC3B1128-Z1UT
QFN 48
Tray
Industrial (-40°C to 85°C)
AT32UC3B164-AUT
TQFP 48
Tray
Industrial (-40°C to 85°C)
AT32UC3B164-Z1UT
QFN 48
Tray
Industrial (-40°C to 85°C)
51
32059ES–AVR32–12/07
AT32UC3B
14. Errata
All parts labelled with -ES (for engineering samples) are revision B parts.
All part not labelled with -ES are revision E parts.
14.1
Rev. E
This version will be sampled in January 2008.
14.1.1
PWM
1. PWM channel interrupt enabling triggers an interrupt
When enabling a PWM channel that is configured with center aligned period (CALG=1), an
interrupt is signalled.
Fix/Workaround
When using center aligned mode, enable the channel and read the status before channel
interrupt is enabled.
14.1.2
SPI
1. SPI Slave / PDCA transfer: no TX UNDERRUN flag
There is no TX UNDERRUN flag available, therefore in SPI slave mode, there is no way to
be informed of a character lost in transmission.
Fix/Workaround
For PDCA transfer: none.
2. SPI Bad serial clock generation on 2nd chip select when SCBR=1, CPOL=1 and
CNCPHA=0
When multiple CS are in use, if one of the baudrate equals to 1 and one of the others
doesn’t equal to 1, and CPOL=1 and CPHA=0, then an additional pulse will be generated on
SCK.
Fix/Workaround
When multiple CS are in use, if one of the baudrate equals to 1, the other must also equal 1
if CPOL=1 and CPHA=0.
3. SPI Glitch on RXREADY flag in slave mode when enabling the SPI or during the first
transfer
In slave mode, the SPI can generate a false RXREADY signal during enabling of the SPI or
during the first transfer.
Fix/Workaround
1. Set slave mode, set required CPOL/CPHA.
2. Enable SPI.
3. Set the polarity CPOL of the line in the opposite value of the required one.
4. Set the polarity CPOL to the required one.
5. Read the RXHOLDING register.
Transfers can now befin and RXREADY will now behave as expected.
52
32059ES–AVR32–12/07
AT32UC3B
14.2
14.2.1
Rev. B
Processor and Architecture
1. Local Busto fast GPIO not available on silicon Rev B
Local bus is only available for silicon RevE and later.
Fix/Workaround
Do not use if silicon revison older than E.
2. Memory Protection Unit (MPU) is non functional.
Fix/Workaround
Do not use the MPU.
3. Bus error should be masked in Debug mode
If a bus error occurs during debug mode, the processor will not respond to debug commands through the DINST register.
Fix/Workaround
A reset of the device will make the CPU respond to debug commands again.
4.
Read Modify Write (RMW) instructions on data outside the internal RAM does not
work.
Read Modify Write (RMW) instructions on data outside the internal RAM does not work.
Fix/Workaround
Do not perform RMW instructions on data outside the internal RAM.
5.
Need two NOPs instruction after instructions masking interrupts
The instructions following in the pipeline the instruction masking the interrupt through SR
may behave abnormally.
Fix/Workaround
Place two NOPs instructions after each SSRF or MTSR instruction setting IxM or GM in SR
6. Clock connection table on Rev B
Here is the table of Rev B
Figure 14-1. Timer/Counter clock connections on RevB
Source
Name
Connection
Internal
TIMER_CLOCK1
Slow Clock (Internal RC oscillator)
TIMER_CLOCK2
PBA Clock / 4
TIMER_CLOCK3
PBA Clock / 8
TIMER_CLOCK4
PBA Clock / 16
TIMER_CLOCK5
PBA Clock / 32
External
XC0
XC1
XC2
53
32059ES–AVR32–12/07
AT32UC3B
14.2.2
PWM
1. PWM counter restarts at 0x0001
The PWM counter restarts at 0x0001 and not 0x0000 as specified. Because of this the first
PWM period has one more clock cycle.
Fix/Workaround
- The first period is 0x0000, 0x0001, ..., period
- Consecutive periods are 0x0001, 0x0002, ..., period
2. PWM channel interrupt enabling triggers an interrupt
When enabling a PWM channel that is configured with center aligned period (CALG=1), an
interrupt is signalled.
Fix/Workaround
When using center aligned mode, enable the channel and read the status before channel
interrupt is enabled.
3. PWM update period to a 0 value does not work
It is impossible to update a period equal to 0 by the using the PWM update register
(PWM_CUPD).
Fix/Workaround
Do not update the PWM_CUPD register with a value equal to 0.
4.
PWM channel status may be wrong if disabled before a period has elapsed
Before a PWM period has elapsed, the read channel status may be wrong. The CHIDx-bit
for a PWM channel in the PWM Enable Register will read '1' for one full PWM period even if
the channel was disabled before the period elapsed. It will then read '0' as expected.
Fix/Workaround
Reading the PWM channel status of a disabled channel is only correct after a PWM period
has elapsed.
14.2.3
SPI
1. SPI FDIV option does not work
Selecting clock signal using FDIV = 1 does not work as specified.
Fix/Workaround
Do not set FDIV = 1.
2. SPI FDIV option does not work
Selecting clock signal using FDIV = 1 does not work as specified.
Fix/Workaround
Do not set FDIV = 1.
54
32059ES–AVR32–12/07
AT32UC3B
3. SPI Slave / PDCA transfer: no TX UNDERRUN flag
There is no TX UNDERRUN flag available, therefore in SPI slave mode, there is no way to
be informed of a character lost in transmission.
Fix/Workaround
For PDCA transfer: none.
4. SPI Bad serial clock generation on 2nd chip select when SCBR=1, CPOL=1 and
CNCPHA=0
When multiple CS are in use, if one of the baudrate equals to 1 and one of the others
doesn’t equal to 1, and CPOL=1 and CPHA=0, then an additional pulse will be generated on
SCK.
Fix/Workaround
When multiple CS are in use, if one of the baudrate equals to 1, the other must also equal 1
if CPOL=1 and CPHA=0.
5. SPI Glitch on RXREADY flag in slave mode when enabling the SPI or during the first
transfer
In slave mode, the SPI can generate a false RXREADY signal during enabling of the SPI or
during the first transfer.
Fix/Workaround
1. Set slave mode, set required CPOL/CPHA.
2. Enable SPI.
3. Set the polarity CPOL of the line in the opposite value of the required one.
4. Set the polarity CPOL to the required one.
5. Read the RXHOLDING register.
Transfers can now befin and RXREADY will now behave as expected.
14.2.4
Power Manager
1. PLL Lock control does not work
PLL lock Control does not work.
Fix/Workaround
In PLL Control register, the bit 7 should be set in order to prevent unexpected behaviour.
2. Wrong reset causes when BOD is activated
Setting the BOD enable fuse will cause the Reset Cause Register to list BOD reset as the
reset source even though the part was reset by another source.
Fix/Workaround
Do not set the BOD enable fuse, but activate the BOD as soon as your program starts.
14.2.5
SSC
1. SSC does not trigger RF when data is low
The SSC cannot transmit or receive data when CKS = CKDIV and CKO = none, in TCMR or
RCMR respectively.
55
32059ES–AVR32–12/07
AT32UC3B
Fix/Workaround
Set CKO to a value that is not "none" and bypass the output of the TK/RK pin with the GPIO.
14.2.6
USB
1.
USB No end of host reset signaled upon disconnection
In host mode, in case of an unexpected device disconnection whereas a usb reset is being
sent by the usb controller, the UHCON.RESET bit may not been cleared by the hardware at
the end of the reset.
Fix/Workaround
A software workaround consists in testing (by polling or interrupt) the disconnection
(UHINT.DDISCI == 1) while waiting for the end of reset (UHCON.RESET == 0) to avoid
being stuck.
2.
USBFSM and UHADDR1/2/3 registers are not available.
Do not use USBFSM register.
Fix/Workaround
Do not use USBFSM register and use HCON[6:0] field instead for all the pipes.
14.2.7
Cycle counter
1. CPU Cycle Counter does not reset the COUNT system register on COMPARE match.
The device revision B does not reset the COUNT system register on COMPARE match. In
this revision, the COUNT register is clocked by the CPU clock, so when the CPU clock
stops, so does incrementing of COUNT.
Fix/Workaround
None.
14.2.8
ADC
1.
ADC possible miss on DRDY when disabling a channel
The ADC does not work properly when more than one channel is enabled.
Fix/Workaround
Do not use the ADC with more than one channel enabled at a time.
2.
ADC OVRE flag sometimes not reset on Status Register read
The OVRE flag does not clear properly if read simultaneously to an end of conversion.
Fix/Workaround
None.
14.2.9
USART
1.
USART Manchester Encoder Not Working
Manchester encoding/decoding is not working.
Fix/Workaround
56
32059ES–AVR32–12/07
AT32UC3B
Do not use manchester encoding.
2.
USART RXBREAK problem when no timeguard
In asynchronous mode the RXBREAK flag is not correctly handled when the timeguard is 0
and the break character is located just after the stop bit.
Fix/Workaround
If the NBSTOP is 1, timeguard should be different from 0.
3.
USART Handshaking: 2 characters sent / CTS rises when TX
If CTS switches from 0 to 1 during the TX of a character, if the Holding register is not empty,
the TXHOLDING is also transmitted.
Fix/Workaround
None.
4.
USART PDC and TIMEGUARD not supported in MANCHESTER
Manchester encoding/decoding is not working.
Fix/Workaround
Do not use manchester encoding.
5.
14.2.10
USART SPI mode is non functional on this revision
Fix/Workaround
Do not use the USART SPI mode.
HMATRIX
1. HMatrix fixed priority arbitration does not work
Fixed priority arbitration does not work.
Fix/Workaround
Use Round-Robin arbitration instead.
14.2.11
Clock caracteristic
1. PBA max frequency
The Peripheral bus A (PBA) max frequency is 30MHz instead of 60MHz.
Fix/Workaround
Do not set the PBA maximum frequency higher than 30MHz.
57
32059ES–AVR32–12/07
AT32UC3B
15. Datasheet Revision History
Please note that the referring page numbers in this section are referred to this document. The
referring revision in this section are referring to the document revision.
15.1
15.2
15.3
15.4
15.5
Rev. E – 12/07
1.
Updated ”Memory protection” on page 18.
1.
Updated ”The AVR32UC CPU” on page 16.
2.
Updated ”Electrical Characteristics” on page 30.
1.
Updated ”Features” on page 1.
2.
Updated block diagram with local bus Figure 3-1 on page 4.
3.
Add schematic for HMatrix master/slave connection Figure 9-1 on page 29.
4.
Updated ”Peripherals” on page 32 with local bus.
5.
Added SPI feature ”Universial Synchronous/Asynchronous Receiver/Transmitter
(USART)” on page 298.
6.
Updated ”USB On-The-Go Interface (USBB)” on page 367.
7.
Updated ADC trigger selection in ”Analog-to-Digital Converter (ADC)” on page 568.
8.
Updated ”JTAG and Boundary Scan” on page 594 with programming procedure.
9.
Add description for silicon revision D page 52.
10.
Add ABDAC Chapter
1.
Updated registered trademarks
2.
Updated address page.
1.
Initial revision.
Rev. D – 11/07
Rev. C – 10/07
Rev. B – 07/07
Rev. A – 05/07
58
32059ES–AVR32–12/07
AT32UC3B
59
32059ES–AVR32–12/07
AT32UC3B
Table of Contents
1
Description ............................................................................................... 2
2
Configuration Summary .......................................................................... 3
3
Blockdiagram ........................................................................................... 4
3.1Processor and architecture ........................................................................................5
4
Package and Pinout ................................................................................. 6
5
Signals Description .................................................................................. 8
6
Power Considerations ........................................................................... 12
6.1Power Supplies ........................................................................................................12
6.2Voltage Regulator ....................................................................................................13
6.3Analog-to-Digital Converter (A.D.C) reference. .......................................................14
7
I/O Line Considerations ......................................................................... 15
7.1JTAG pins ................................................................................................................15
7.2RESET_N pin ..........................................................................................................15
7.3TWI pins ..................................................................................................................15
7.4GPIO pins ................................................................................................................15
7.5High drive pins .........................................................................................................15
8
Memories ................................................................................................ 16
8.1Embedded Memories ..............................................................................................16
8.2Physical Memory Map .............................................................................................16
8.3Bus Matrix Connections ...........................................................................................17
9
Peripherals .............................................................................................. 19
9.1Peripheral Address Map ..........................................................................................19
9.2CPU Local Bus Mapping .........................................................................................20
9.3Interrupt Request Signal Map ..................................................................................20
9.4Clock Connections ...................................................................................................22
9.5Nexus OCD AUX port connections ..........................................................................23
9.6DMA handshake signals ..........................................................................................23
9.7High Drive Current GPIO .........................................................................................24
9.8Peripheral Multiplexing on I/O lines .........................................................................24
9.9Oscillator Pinout ......................................................................................................25
9.10Peripheral overview ...............................................................................................26
i
32059ES–AVR32–12/07
AT32UC3B
10 Boot Sequence ....................................................................................... 29
10.1Starting of clocks ...................................................................................................29
10.2Fetching of initial instructions ................................................................................29
11 Electrical Characteristics ...................................................................... 30
11.1Absolute Maximum Ratings* .................................................................................30
11.2DC Characteristics .................................................................................................31
11.3Regulator characteristics .......................................................................................32
11.4Analog characteristics ...........................................................................................32
11.5Power Consumption ..............................................................................................33
11.6Clock Characteristics .............................................................................................35
11.7Crystal Oscillator Characteristis ............................................................................37
11.8ADC Characteristics ..............................................................................................39
11.9JTAG/ICE Timings .................................................................................................40
11.10SPI Characteristics ..............................................................................................42
11.11Flash Characteristics ...........................................................................................44
12 Mechanical Characteristics ................................................................... 45
12.1Thermal Considerations ........................................................................................45
12.2Package Drawings .................................................................................................46
12.3Soldering Profile ....................................................................................................50
13 Ordering Information ............................................................................. 51
14 Errata ....................................................................................................... 52
14.1Rev. E ....................................................................................................................52
14.2Rev. B ....................................................................................................................53
15 Datasheet Revision History ................................................................... 58
15.1Rev. E – 12/07 .......................................................................................................58
15.2Rev. D – 11/07 .......................................................................................................58
15.3Rev. C – 10/07 .......................................................................................................58
15.4Rev. B – 07/07 .......................................................................................................58
15.5Rev. A – 05/07 .......................................................................................................58
ii
32059ES–AVR32–12/07
Headquarters
International
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Atmel Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Atmel Europe
Le Krebs
8, Rue Jean-Pierre Timbaud
BP 309
78054 Saint-Quentin-enYvelines Cedex
France
Tel: (33) 1-30-60-70-00
Fax: (33) 1-30-60-71-11
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Technical Support
[email protected]
Sales Contact
www.atmel.com/contacts
Product Contact
Web Site
www.atmel.com
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF
THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© 2007 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations thereof, AVR ® and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
32059ES–AVR32–12/07
Similar pages