ON CAT812STBI-GT3 4-pin microprocessor power supply supervisors with manual reset Datasheet

CAT811, CAT812
4-Pin Microprocessor
Power Supply Supervisors
with Manual Reset
Description
The CAT811 and CAT812 are microprocessor supervisory circuits
that monitor power supplies. The CAT811 and CAT812 are direct
replacements for the MAX811 and MAX812 in applications operating
over the industrial temperature range; both have a manual reset input.
These devices generate a reset signal, which is asserted while the
power supply voltage is below a preset threshold level and for at least
140 ms after the power supply level has risen above that level. The
underlying floating gate technology, Analog EEPROM used by
ON Semiconductor, makes it possible to offer any custom reset
threshold value. Seven industry standard threshold levels are offered
to support +5.0 V, +3.3 V, +3.0 V and +2.5 V systems.
The CAT811 features a RESET push−pull output (active LOW) and
the CAT812 features a RESET push−pull output (active HIGH).
Fast transients on the power supply are ignored and the output is
guaranteed to be in the correct state at Vcc levels as low as 1.0 V.
The CAT811/812 are fully specified over the industrial temperature
range (−40°C to 85°C) and are available in a compact 4−pin SOT−143
package.
Features
http://onsemi.com
SOT−143
BI SUFFIX
CASE 527AF
PIN CONFIGURATION
1
•
•
•
•
•
•
•
•
•
VCC
GND
2
3
MR
RESET
• Precision Monitoring of
+5.0 V (± 5%, ± 10%, ± 20%),
+3.3 V (± 5%, ± 10%),
+3.0 V (± 10%) and
+2.5 V (± 5%) Power Supplies
Manual Reset Input
Offered in Two Output Configurations: CAT811: Active LOW Reset
CAT812: Active HIGH Reset
Direct Replacements for the MAX811 and MAX812 in Applications
Operating over the Industrial Temperature Range
Reset Valid down to VCC = 1.0 V
6 mA Power Supply Current
Power Supply Transient Immunity
Available in SOT−143 Packages with Sn or NiPdAu Green Lead
Finishes
Industrial Temperature Range: −40°C to +85°C
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
4
(Top View)
MARKING DIAGRAM
XXXMG
G
1
XXX
M
G
= Specific Device Code
= Month Code
= Pb−Free Package
(*Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
Applications
•
•
•
•
•
•
Computers, Servers, Laptops and Cable Modems
Wireless Communications
Embedded Control Systems
White Goods, Power Meters
Intelligent Instruments
PDAs and Handheld Equipment
© Semiconductor Components Industries, LLC, 2012
October, 2012 − Rev. 2
1
Publication Order Number:
CAT811/D
CAT811, CAT812
Table 1. THRESHOLD SUFFIX SELECTOR DESCRIPTION
Nominal Threshold Voltage
Threshold Suffix Designation
4.63 V
L
4.38 V
M
4.00 V
J
3.08 V
T
2.93 V
S
2.63 V
R
2.32 V
Z
Table 2. PIN DESCRIPTION
Pin Number
CAT811
CAT812
Pin Name
1
1
GND
2
−
RESET
Active LOW reset. RESET is asserted if VCC falls below the reset threshold and remains low for at least 140 ms after VCC rises above the reset threshold.
−
2
RESET
Active HIGH reset. RESET is asserted if VCC falls below the reset threshold and remains high for at least 140 ms after VCC rises above the reset threshold.
3
3
MR
Manual Reset Input. A logic LOW on MR asserts RESET. RESET remains active as
long as MR is LOW and for 140 ms after MR returns HIGH. The active low input has
an internal 20 kW pull−up resistor. The input should be left open if not used.
4
4
VCC
Power supply voltage that is monitored.
Description
Ground.
VCC
MR
VCC
VCC
TOLERANCE
BIAS
RESET
&
DIGITAL
DELAY
+
–
RESET
VOLTAGE
REFERENCE
CAT811
GND
VCC
MR
VCC
VCC
TOLERANCE
BIAS
RESET
&
DIGITAL
DELAY
+
–
RESET
VOLTAGE
REFERENCE
CAT812
GND
Figure 1. Block Diagrams
http://onsemi.com
2
CAT811, CAT812
Table 3. ABSOLUTE MAXIMUM RATINGS
Parameters
Ratings
Units
−0.3 to +6.0
V
Input Current, VCC
20
mA
Output Current RESET, RESET
20
mA
Rate of Raise, VCC
100
V/ms
Continuous Power Dissipations
Derate 4 mW/°C above +70°C (SOT−143)
320
mW
Storage Temperature Range
−65 to +105
°C
Operating Ambient Temperature Range
−40 to +85
°C
+300
°C
Any pin with respect to ground
Lead Soldering Temperature (10 seconds)
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 4. ELECTRICAL OPERATING CHARACTERISTICS
(VCC = Full range, TA = −40°C to +85°C unless otherwise noted. Typical values at TA = +25°C and VCC = 5 V for the L/M/J versions,
VCC = 3.3 V for the T/S versions, VCC = 3 V for the R version and VCC = 2.5 V for the Z version.)
Parameter
Symbol
VCC Range
Supply Current
Reset Threshold
Voltage
ICC
VTH
Conditions
Min
TA = 0°C to +70°C
TA = −40°C to +85°C
TA = −40°C to +85°C
Typ
Max
Units
1.0
5.5
V
1.2
5.5
VCC < 5.5 V, J/L/M
8
20
VCC < 3.6 V, R/S/T/Z
6
15
4.63
4.70
L Threshold
TA = +25°C
4.56
TA = −40°C to +85°C
4.50
TA = +25°C
4.31
TA = −40°C to +85°C
4.25
TA = +25°C
3.93
TA = −40°C to +85°C
3.89
TA = +25°C
3.04
TA = −40°C to +85°C
3.00
TA = +25°C
2.89
TA = −40°C to +85°C
2.85
TA = +25°C
2.59
TA = −40°C to +85°C
2.55
TA = +25°C
2.28
TA = −40°C to +85°C
2.25
M Threshold
J Threshold
T Threshold
S Threshold
R Threshold
Z Threshold
Reset Threshold
Tempco
VCC to Reset Delay
(Note 3)
VCC = VTH to (VTH − 100 mV)
Reset Active
Timeout Period
TA = −40°C to +85°C
1. Production testing done at TA = +25°C; limits over temperature guaranteed by design only.
2. Glitches of 100 ns or less typically will not generate a reset pulse.
3. RESET output for the CAT811; RESET output for the CAT812.
http://onsemi.com
3
140
mA
V
4.75
4.38
4.45
4.50
4.00
4.06
4.10
3.08
3.11
3.15
2.93
2.96
3.00
2.63
2.66
2.70
2.32
2.35
2.38
30
ppm/°C
20
ms
240
400
ms
CAT811, CAT812
Table 4. ELECTRICAL OPERATING CHARACTERISTICS
(VCC = Full range, TA = −40°C to +85°C unless otherwise noted. Typical values at TA = +25°C and VCC = 5 V for the L/M/J versions,
VCC = 3.3 V for the T/S versions, VCC = 3 V for the R version and VCC = 2.5 V for the Z version.)
Parameter
Symbol
Conditions
RESET Output
Voltage Low
(Push−pull, active
LOW, CAT811)
VOL
RESET Output
Voltage High
(Push−pull, active
LOW, CAT811)
VOH
RESET Output
Voltage Low
(Push−pull, active
HIGH, CAT812)
VOL
RESET Output
Voltage High
(Push−pull active
HIGH, CAT812)
VOH
MR Minimum Pulse
Width
tMR
MR Glitch Immunity
Min
Typ
Max
Units
VCC = VTH min, ISINK = 1.2 mA CAT811R/S/T/Z
0.3
V
VCC = VTH min, ISINK = 3.2 mA CAT811J/L/M
0.4
VCC > 1.0 V, ISINK = 50 mA
0.3
VCC = VTH max, ISOURCE = 500 mA CAT811R/S/T/Z
0.8VCC
V
VCC = VTH max, ISOURCE = 800 mA CAT811J/L/M
VCC − 1.5
V
VCC > VTH max, ISINK = 1.2 mA CAT812R/S/T/Z
0.3
VCC > VTH max, ISINK = 3.2 mA CAT812J/L/M
0.4
1.8 V < VCC ≤ VTH min, ISOURCE = 150 mA
0.8VCC
V
10
ms
(Note 2)
100
ns
0.5
ms
MR to RESET
Propagation Delay
tMD
(Note 3)
MR Input Threshold
VIH
VCC > VTH (MAX), CAT811/812L/M/J
V
2.3V
VIL
VIH
V
0.8
VCC > VIH (MAX), CAT811/812R/S/T/Z
0.7VCC
VIL
0.25VCC
MR Pull−up
Resistance
10
1. Production testing done at TA = +25°C; limits over temperature guaranteed by design only.
2. Glitches of 100 ns or less typically will not generate a reset pulse.
3. RESET output for the CAT811; RESET output for the CAT812.
http://onsemi.com
4
20
75
kW
CAT811, CAT812
TYPICAL OPERATING CHARACTERISTICS
(VCC = Full range, TA = −40°C to +85°C unless otherwise noted. Typical values at TA = +25°C and VCC = 5 V for the L/M/J versions,
VCC = 3.3 V for the T/S versions, VCC = 3 V for the R version and VCC = 2.5 V for the Z version.)
12
SUPPLY CURRENT (mA)
240
VCC = 5 V
220
VCC = 2.5 V
200
180
160
−50
0
50
100
10
VCC = 5.5 V
8
4
2
0
50
100
150
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 2. Power−Up Reset Timeout vs.
Temperature
Figure 3. Supply Current vs. Temperature
(No Load, CAT8xxR/S/T/Z)
14
1.0002
12
1.0000
10
8
6
4
2
0
−50
VCC = 3.6 V
6
0
−50
150
NORMALIZED THRESHOLD
POWER−DOWN RESET DELAY (s)
POWER−UP RESET TIMEOUT (ms)
260
0
50
100
0.9998
0.9996
0.9994
0.9992
0.9990
0.9988
150
0
20
40
60
80
100
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 4. Power−Down Reset Delay vs.
Temperature (CAT8xxR/S/T/Z)
Figure 5. Normalized Reset Threshold vs.
Temperature
http://onsemi.com
5
120
CAT811, CAT812
DETAILED DESCRIPTION
Reset Timing
The reset signal is asserted LOW for the CAT811 and HIGH for the CAT812 when the power supply voltage falls below the
threshold trip voltage and remains asserted for at least 140 ms after the power supply voltage has risen above the threshold.
Threshold
Voltage
5V
VCC
0V
CAT811
RESET
CAT812
RESET
140 ms
minimum
5V
Reset
Timeout Period
0V
VCC
0V
Figure 6. Reset Timing Diagram
VCC Transient Response
Valid Reset with VCC under 1.0 V
The CAT811/812 protect mPs against brownout failure.
Short duration transients of 4 ms or less and 100 mV
amplitude typically do not cause a false RESET.
Figure 7 shows the maximum pulse duration of
negative−going VCC transients that do not cause a reset
condition. As the amplitude of the transient goes further
below the threshold (increasing VTH − VCC), the maximum
pulse duration decreases. In this test, the VCC starts from an
initial voltage of 0.5 V above the threshold and drops below
it by the amplitude of the overdrive voltage (VTH − VCC).
To ensure that the CAT811 RESET pin is in a known state
when VCC is under 1.0 V, a 100 kW pull−down resistor
between RESET pin and GND is recommended; the value
is not critical. For the CAT812, a pull−up resistor from
RESET pin to VCC is needed.
Power
Supply
VCC
CAT811
30
TRANSIENT DURATION (ms)
TAMB = 25°C
MR RESET
25
GND
100 kW
20
CAT8xxZ
15
Figure 8. RESET Valid with VCC Under 1.0 V
CAT8xxM
10
Power
Supply
5
0
VCC
1
10
100
1000
CAT812
RESET OVERDRIVE VTH − VCC (mV)
Figure 7. Maximum Transient Duration without
Causing a Reset Pulse vs. Reset Comparator
Overdrive
MR
100 kW
RESET
GND
Figure 9. RESET Valid with VCC Under 1.1 V
http://onsemi.com
6
CAT811, CAT812
Bi−directional Reset Pin Interfacing
The CAT811/812 can interface with mP/mC bi−directional reset pins by connecting a 4.7 kW resistor in series with the
CAT811/812 reset output and the mP/mC bi−directional reset pin.
BUF
Buffered
RESET
Power
Supply
CAT811
VCC
mP
4.7 kW
MR
RESET
(for example: 68HC11)
RESET
INPUT
C AT8 11
GND
GND
Bi−directional I/O Pin
Figure 10. Bi−directional Reset Pin Interfacing
Table 5. OTHER SUPERVISORY PRODUCTS
Function
CAT1161/3
CAT1162
With 16k Bit Serial EEPROM Memory
a
a
Watchdog Timer
a
Manual Reset Input
a
CAT809
a
a
Active Low Reset
Package
CAT811
CAT812
a
a
a
a
Active High Reset
Dual Polarity Reset Outputs
CAT810
a
a
8−pin DIP
and SOIC
8−pin DIP
and SOIC
3−pin SOT−23
and SC70
http://onsemi.com
7
3−pin SOT−23
and SC70
a
4−pin
SOT−143
4−pin
SOT−143
CAT811, CAT812
PACKAGE DIMENSIONS
SOT−143, 4 Lead
CASE 527AF−01
ISSUE A
SYMBOL
MIN
NOM
MAX
A
0.80
1.22
D
A1
0.05
0.15
e
A2
0.75
4
3
E1
1
E
2
e1
b
0.30
0.50
0.76
0.89
c
0.08
0.20
D
2.80
E
2.10
E1
1.20
1.30
1.92 BSC
0.20 BSC
0.40
0.50
8°
c
L
A1
L1
SIDE VIEW
END VIEW
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC TO-253.
http://onsemi.com
8
0.60
0.25
0°
q
b2
1.40
0.54 REF
θ
A
3.04
2.64
e
L2
A2
2.90
e1
L1
TOP VIEW
1.07
b2
L
b
0.90
L2
CAT811, CAT812
ORDERING INFORMATION
Output
Reset
Package
Quantity
per Reel
(Note 5)
Manual
Reset
LOW
SOT−143−4
3,000
Manual
Reset
HIGH
SOT−143−4
3,000
Top Mark (Note 4)
Order Number
NiPdAu
Matte−Tin
Voltage
NiPdAu
Matte−Tin
CAT811LTBI−GT3
CAT811LTBI−T3
4.63 V
VEA
VES
CAT811MTBI−GT3
CAT811MTBI−T3
4.38 V
VEA
VES
CAT811JTBI−GT3
CAT811JTBI−T3
4.00 V
VEA
VES
CAT811TTBI−GT3
CAT811TTBI−T3
3.08 V
VEA
VES
CAT811STBI−GT3
CAT811STBI−T3
2.93 V
VEA
VES
CAT811RTBI−GT3
CAT811RTBI−T3
2.63 V
VEA
VES
CAT811ZTBI−GT3
CAT811ZTBI−T3
2.32 V
VEA
VES
CAT812LTBI−GT3
CAT812LTBI−T3
4.63 V
VTA
VTS
CAT812MTBI−GT3
CAT812MTBI−T3
4.38 V
VTA
VTS
CAT812JTBI−GT3
CAT812JTBI−T3
4.00 V
VTA
VTS
CAT812TTBI−GT3
CAT812TTBI−T3
3.08 V
VTA
VTS
CAT812STBI−GT3
CAT812STBI−T3
2.93 V
VTA
VTS
CAT812RTBI−GT3
CAT812RTBI−T3
2.63 V
VTA
VTS
CAT812ZTBI−GT3
CAT812ZTBI−T3
2.32 V
VTA
VTS
4. Threshold and full part numbers will be provided on box and reel labels as well as all Shipping documents.
5. For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
6. For detailed information and a breakdown of device nomenclature and numbering systems, please see the ON Semiconductor Device
Nomenclature document, TND310/D, available at www.onsemi.com
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
9
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
CAT811/D
Similar pages