LINER LT1011MH Pin compatible with lm111 series device Datasheet

LT1011/LT1011A
Voltage Comparator
Features
n
n
n
n
n
n
n
n
n
n
Description
Pin Compatible with LM111 Series Devices
Guaranteed Max 0.5mV Input Offset Voltage
Guaranteed Max 25nA Input Bias Current
Guaranteed Max 3nA Input Offset Current
Guaranteed Max 250ns Response Time
Guaranteed Min 200,000 Voltage Gain
50mA Output Current Source or Sink
±30V Differential Input Voltage
Fully Specified for Single 5V Operation
Available in 8-Lead PDIP and SO Packages
The LT®1011 is a general purpose comparator with significantly better input characteristics than the LM111.
Although pin compatible with the LM111, it offers four
times lower bias current, six times lower offset voltage
and five times higher voltage gain. Offset voltage drift,
a previously unspecified parameter, is guaranteed at
15µV/°C. Additionally, the supply current is lower by
a factor of two with no loss in speed. The LT1011 is
several times faster than the LM111 when subjected to
large overdrive conditions. It is also fully specified for DC
parameters and response time when operating on a single
5V supply. The LT1011 retains all the versatile features of
the LM111, including single 3V to ±18V supply operation,
and a floating transistor output with 50mA source/sink
capability. It can drive loads referenced to ground, negative supply or positive supply, and is specified up to 50V
between V– and the collector output. A differential input
voltage up to the full supply voltage is allowed, even with
±18V supplies, enabling the inputs to be clamped to the
supplies with simple diode clamps.
Applications
n
n
n
n
n
n
n
SAR A/D Converters
Voltage-to-Frequency Converters
Precision RC Oscillator
Peak Detector
Motor Speed Control
Pulse Generator
Relay/Lamp Driver
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
Typical Application
10µs 12-Bit A/D Converter
Response Time vs Overdrive
15V
LM329
7V
R3
6.98k
*R2 AND R4
SHOULD TC TRACK
–15V
0.001µF
500
450
400
INPUT
0V TO 10V
6012
12-BIT
D/A CONVERTER
R4*
2.49k
R6
820Ω
PARALLEL
OUTPUTS
PARALLEL
OUTPUTS
5V
+
R5
1k
LT1011A
D
5V
E
350
300
250
200
150
FALLING
OUTPUT
RISING
OUTPUT
100
–
50
0
0.1
SERIAL OUTPUT
AM2504
SAR REGISTER
RESPONSE TIME (ns)
15V
3.9k
R1
1k
FULL-SCALE
TRIM
R2*
6.49k
7475
LATCH
1
10
OVERDRIVE (mV)
100
1011 TA02
CC
S
S
CP
START
CLOCK f = 1.4MHz
1011 TA01
1011afe
For more information www.linear.com/LT1011
1
LT1011/LT1011A
Absolute Maximum Ratings
(Note 1)
Supply Voltage (Pin 8 to Pin 4)..................................36V
Output to Negative Supply (Pin 7 to Pin 4)
LT1011AC, LT1011C................................................40V
LT1011AI, LT1011I..................................................40V
LT1011AM, LT1011M (OBSOLETE)........................50V
Ground to Negative Supply (Pin 1 to Pin 4)...............30V
Differential Input Voltage.........................................±36V
Voltage at STROBE Pin (Pin 6 to Pin 8)........................5V
Input Voltage (Note 2)...........................Equal to Supplies
Output Short-Circuit Duration................................10 sec
Operating Temperature Range (Note 3)
LT1011AC, LT1011C................................... 0°C to 70°C
LT1011AI, LT1011I.................................–40°C to 85°C
LT1011AM, LT1011M (OBSOLETE)..... –55°C to 125°C
Storage Temperature Range................... –65°C to 150°C
Lead Temperature (Soldering, 10 sec).................... 300°C
Pin Configuration
TOP VIEW
V+
GND 1
INPUT+ 2
8
+
–
TOP VIEW
7 OUTPUT
6
GND 1
BALANCE/
STROBE
INPUT – 3
5 BALANCE
4
V–
H PACKAGE
8-LEAD TO-5 METAL CAN
INPUT+ 2
INPUT – 3
V– 4
N8 PACKAGE
8-LEAD PDIP
+
–
8
V+
7
OUTPUT
BALANCE/
STROBE
BALANCE
6
5
S8 PACKAGE
8-LEAD PLASTIC SO
TJMAX = 150°C, θJA = 130°C/W(N8)
TJMAX = 150°C, θJA = 150°C/W(S8)
TJMAX = 150°C, θJA = 150°C/W, θJC = 45°C/W
OBSOLETE PACKAGE
Consider the N8 or S8 Packages for Alternate Source
1011afe
2
For more information www.linear.com/LT1011
LT1011/LT1011A
Order Information
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT1011ACN8#PBF
N/A
LT1011
8-Lead Plastic DIP
0°C to 70°C
LT1011CN8#PBF
N/A
LT1011
8-Lead Plastic DIP
0°C to 70°C
LT1011AIS8#PBF
LT1011AIS8#TRPBF
1011AI
8-Lead Plastic SO
–40°C to 85°C
LT1011CS8#PBF
LT1011CS8#TRPBF
1011
8-Lead Plastic SO
0°C to 70°C
LT1011IS8#PBF
LT1011IS8#TRPBF
1011I
8-Lead Plastic SO
–40°C to 85°C
OBSOLETE PACKAGES
LT1011ACH#PBF
N/A
8-Lead TO-5 Metal Can
–55°C to 125°C
LT1011CH#PBF
N/A
8-Lead TO-5 Metal Can
–55°C to 125°C
LT1011AMH#PBF
N/A
8-Lead TO-5 Metal Can
–55°C to 125°C
LT1011MH#PBF
N/A
8-Lead TO-5 Metal Can
–55°C to 125°C
LT1011ACJ8#PBF
N/A
8-Lead CERDIP
–55°C to 125°C
LT1011CJ8#PBF
N/A
8-Lead CERDIP
–55°C to 125°C
LT1011AMJ8#PBF
N/A
8-Lead CERDIP
–55°C to 125°C
LT1011MJ8#PBF
N/A
8-Lead CERDIP
–55°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on nonstandard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
1011afe
For more information www.linear.com/LT1011
3
LT1011/LT1011A
Electrical Characteristics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = ±15V, VCM = 0V, RS = 0Ω, VGND = –15V, output at pin 7 unless
otherwise noted.
LT1011AC/AI/AM
SYMBOL PARAMETER
VOS
Input Offset Voltage
*Input Offset Voltage
CONDITIONS
MIN
TYP
MAX
0.3
●
0.5
1
●
0.75
1.5
(Note 4)
RS ≤ 50k (Note 5)
IOS
*Input Offset Current
(Note 5)
IB
Input Bias Current
(Note 4)
*Input Bias Current
(Note 5)
LT1011C/I/M
MIN
TYP
MAX
0.6
1.5
3
UNITS
mV
mV
2
3
mV
mV
0.2
3
5
0.2
4
6
nA
nA
15
25
20
50
nA
20
35
50
25
65
80
nA
nA
4
15
4
25
µV/°C
●
●
∆VOS
∆T
Input Offset Voltage Drift
(Note 6)
TMIN ≤ T ≤ TMAX
AVOL
*Large-Signal Voltage Gain
RL = 1k Connected to 15V,
–10V ≤ VOUT ≤ 14.5V
200
500
200
500
V/mV
RL = 500Ω Connected to 5V,
VS = Single 5V, VGND = 0V,
0.5V ≤ VOUT ≤ 4.5V
50
300
50
300
V/mV
94
115
90
115
CMRR
●
Common Mode Rejection Ratio
*Input Voltage Range (Note 9)
VS = ±15V
VS = Single 5V
● –14.5
● 0.5
tD
*Response Time
(Note 7)
VOL
*Output Saturation Voltage,
VGND = 0
VIN = –5mV, ISINK = 8mA, TJ ≤ 100°C
VIN = –5mV, ISINK = 8mA
VIN = –5mV, ISINK = 50mA
●
●
*Output Leakage Current
VIN = 5mV, VGND = –15V,
VOUT = 20V
●
13
3
–14.5
0.5
dB
13
3
V
V
150
250
150
250
ns
0.25
0.25
0.7
0.4
0.45
1.5
0.25
0.25
0.7
0.4
0.45
1.5
V
V
V
0.2
10
500
0.2
10
500
nA
nA
*Positive Supply Current
VGND = 0
3.2
4
3.2
4
mA
*Negative Supply Current
VGND = 0
1.7
2.5
1.7
2.5
mA
*Strobe Current (Note 8)
Minimum to Ensure Output Transistor is Off,
VGND = 0
Input Capacitance
500
500
6
µA
6
pF
*Indicates parameters which are guaranteed for all supply voltages, including a single 5V supply. See Note 5.
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Inputs may be clamped to supplies with diodes so that
maximum input voltage actually exceeds supply voltage by one diode
drop. See Input Protection in the Applications Information section.
Note 3: TJMAX = 150°C.
Note 4: Output is sinking 1.5mA with VOUT = 0V.
Note 5: These specifications apply for all supply voltages from a single
5V to ±15V, the entire input voltage range, and for both high and low
output states. The high state is ISINK = 100µA, VOUT = (V+ – 1V) and
the low state is ISINK = 8mA, VOUT = 0.8V. Therefore, this specification
defines a worst-case error band that includes effects due to common
mode signals, voltage gain and output load.
Note 6: Drift is calculated by dividing the offset voltage difference
measured at min and max temperatures by the temperature difference.
Note 7: Response time is measured with a 100mV step and 5mV
overdrive. The output load is a 500Ω resistor tied to 5V. Time
measurement is taken when the output crosses 1.4V.
Note 8: Do not short the STROBE pin to ground. It should be current
driven at 3mA to 5mA for the shortest strobe time. Currents as low
as 500µA will strobe the LT1011A if speed is not important. External
leakage on the STROBE pin in excess of 0.2µA when the strobe is “off”
can cause offset voltage shifts.
Note 9: See graph “Input Offset Voltage vs Common Mode Voltage.”
1011afe
4
For more information www.linear.com/LT1011
LT1011/LT1011A
Typical Performance Characteristics
Input Offset Current
0.8
35
0.7
30
0.6
25
20
15
0.5
0.4
0.3
10
0.2
5
0.1
0
0
–50 –25
25 50 75 100 125 150
TEMPERATURE (°C)
0
Input Characteristics*
–15
–20
–25
–30
–35
TA = 25°C
–1.5
–2.0
REFERRED TO SUPPLIES
0.4
0.3
NEGATIVE LIMIT
0.2
COLLECTOR
OUTPUT
RL = 1k
40
30
20
10
EMITTER
OUTPUT
RL = 600Ω
0.1
–40
–20 –15 –10 –5
0
5
10
INPUT VOLTAGE (V)
15
20
V–
–50 –25
OVERDRIVE
20mV
5mV
2mV
3
2
VIN
–
500Ω
1
VIN
OVERDRIVE
20mV
5mV
2mV
3
2
1
+
0
15V
–
5V
–15V
0
–15V
100mV
0
INPUT = 100mV STEP
0
0
INPUT = 100mV STEP
–100mV
50 100 150 200 250 300 350 400 450
TIME (ns)
1011 G07
0
PIN 1 GROUNDED
0.9
500Ω
+
0.5
Collector Output Saturation
Voltage
1.0
VS = ±15V
4
5V
–0.3
0.1
0.3
–0.1
DIFFERENTIAL INPUT VOLTAGE (mV)
1011 G06
Response Time—Collector Output
5
15V
0
– 0.5
25 50 75 100 125 150
TEMPERATURE (°C)
1011 G05
6
VS = ±15V
4
0
1011 G04
Response Time—Collector Output
5
POSITIVE LIMIT
–1.0
1M
Transfer Function (Gain)
–0.5
–10
6
10k
100k
SOURCE RESISTANCE (Ω)
1k
50
SATURATION VOLTAGE (V)
–5
Common Mode Limits
*EITHER INPUT.
REMAINING INPUT GROUNDED.
CURRENT FLOWS OUT OF INPUT.
VS = ±15V
LT1011AM
LT1011AC
1
1011 G03
V+
COMMON MODE VOLTAGE (V)
INPUT CURRENT (nA)
0
LT1011M
LT1011C
1011 G02
1011 G01
5
LM311
(FOR COMPARISON)
10
0.1
25 50 75 100 125 150
TEMPERATURE (°C)
OUTPUT VOLTAGE (V)
0
–50 –25
Worst-Case Offset Error
100
EQUIVALENT OFFSET VOLTAGE (mV)
IB FLOWS OUT
40 OF INPUTS
0.9
CURRENT (nA)
CURRENT (nA)
Input Bias Current
45
0.8
TA = 125°C
0.7
TA = 25°C
0.6
0.5
0.4
TA = –55°C
0.3
0.2
0.1
50 100 150 200 250 300 350 400 450
TIME (ns)
1011 G08
0
0
5
10 15 20 25 30 35 40 45 50
SINK CURRENT (mA)
1011 G09
1011afe
For more information www.linear.com/LT1011
5
LT1011/LT1011A
Typical Performance Characteristics
5mV
2mV
5
–
VIN
0
V+
+
–5
VOUT
–10
2k
–15
V–
0
–50
VS = ±15V
TA = 25°C
–100
0
1
4
3
2
TIME (µs)
V+
15
VIN
10
5
–
+
0
VOUT
2k
–5
–10
5mV
20mV
–15
V–
2mV
–100
VS = ±15V
TA = 25°C
–50
0
0
1
2
TIME (µs)
Supply Current vs Supply Voltage
60
0.2
40
20
3
2
1
5
10
15
20
SUPPLY VOLTAGE (V)
25
1011 G13
+
2
+
3
–
4
LT1011
V–
TJ = –55°C
2
V+
8
100
125
VOUT
TJ = 25°C
TJ = 125°C
1
10
10–8
VOUT = 35V
VGND = –15V
10–9
10–10
10–11
25
TJ = 125°C
0.4
TJ = 25°C
0.3
0.2
30
40
20
OUTPUT CURRENT (mA)
50
0
TJ = –55°C
0
1
5
6
3
2
4
INPUT OVERDRIVE (mV)
45
65
85
TEMPERATURE (°C)
105
125
1011 G15
Response Time vs Input Step Size
1000
0.1
0
1011 G12
VS = ±15V
1011 G14
ISINK = 8mA
0.5
7
1 RL
0
Output Leakage Current
Output Saturation Voltage
4
3
50
25
75
0
TEMPERATURE (˚C)
0.6
SATURATION VOLTAGE (V)
REFERRED TO V+
15
POSITIVE AND NEGATIVE SUPPLY
COLLECTOR OUTPUT “HI”
0
–50 –25
30
Output Saturation—
Ground Output
5
10
5
OUTPUT VOLTAGE (V)
0
PROPAGATION DELAY (ns)
0
0.1
*MEASURED 3 MINUTES
AFTER SHORT
10–7
POSITIVE SUPPLY
COLLECTOR OUTPUT “LO”
0.3
SHORT-CIRCUIT
CURRENT
LEAKAGE CURRENT (A)
CURRENT (mA)
CURRENT (mA)
POSITIVE AND NEGATIVE SUPPLY
COLLECTOR OUTPUT “HI”
2
1
V+ TO GROUND PIN VOLTAGE (V)
0.4
Supply Current vs Temperature
4
0.5
80
5
3
0
100
6
4
0.6
POWER
DISSIPATION
1011 G11
5
POSITIVE SUPPLY
COLLECTOR OUTPUT “LO”
0.7
TA = 25°C
120
0
4
3
1011 G10
0
Output Limiting Characteristics*
140
SHORT-CIRCUIT CURRENT (mA)
20mV
10
INPUT VOLTAGE (mV) OUTPUT VOLTAGE (V)
15
Response Time Using GND Pin
as Output
POWER DISSIPATION (W)
INPUT VOLTAGE (mV) OUTPUT VOLTAGE (V)
Response Time Using GND Pin
as Output
7
8
1011 G16
VS = ±15V
RL = 500Ω TO 5V
OVERDRIVE = 5mV
800
INPUT
600
3
–
2
+
5V
500Ω
7
1
400
RISING INPUT
FALLING INPUT
200
0
0
1
2
3
4 5 6 7
INPUT STEP (V)
8
9
10
1011 G18
1011 G17
1011afe
6
For more information www.linear.com/LT1011
LT1011/LT1011A
Typical Performance Characteristics
2.5
INPUT OFFSET VOLTAGE (mV)
2.0
CHANGE IN VOS (mV/µA)
Input Offset Voltage
vs Common Mode Voltage
TJ = 25°C
1.5
UPPER
COMMON MODE
+ – (1.5V)
LIMIT = V
1.0
0.5
0
Offset Pin Characteristics
0.8
0.6
0.4
0.2
0
–0.5
–150mV
–1.0
–1.5
–2.0
–2.5
V– (OR GND WITH
SINGLE SUPPLY)
V– 0.1 0.2 0.3 0.4 0.5 0.6 0.7
COMMON MODE VOLTAGE (V)
CHANGE IN VOS FOR CURRENT
INTO PINS 5 OR 6
VOLTAGE ON PINS 5 AND 6
WITH RESPECT TO V+
–100mV
–50mV
V+
0
–50 –25
1011 G19
0
25 50 75 100 125 150
TEMPERATURE (°C)
1011 G20
Pin Functions
GND (PIN 1): Ground.
INPUT+ (PIN 2): Non-Inverting Input of Comparator
INPUT– (PIN 3): Inverting Input of Comparator
V– (PIN 4): Negative Supply Voltage
OUT (PIN 7): Open-Collector Output of Comparator
BALANCE (PIN 5): Balance Input. This input can be used
to adjust the input voltage offset or to add hysteresis. If
offset balancing or hysteresis is not used, the BALANCE
pins should be connected together with a 0.1µF capacitor.
BALANCE/STROBE (PIN 6): Strobe Input Pin. Using this
pin, the output transistor can be forced to an “off” state,
giving a “hi” output at the collector (Pin 7). This input can
be used to adjust the input voltage offset or used to add
hysteresis. If offset balancing or hysteresis is not used,
the BALANCE pins should be connected together with a
0.1µF capacitor.
V+ (PIN 8): Positive Supply Voltage
1011afe
For more information www.linear.com/LT1011
7
LT1011/LT1011A
Applications Information
Preventing Oscillation Problems
Oscillation problems in comparators are nearly always
caused by stray capacitance between the output and
inputs or between the output and other sensitive pins
on the comparator. This is especially true with high
gain bandwidth comparators like the LT1011, which are
designed for fast switching with millivolt input signals.
The gain bandwidth product of the LT1011 is over 10GHz.
Oscillation problems tend to occur at frequencies around
5MHz, where the LT1011 has a gain of ≈2000. This implies
that attenuation of output signals must be at least 2000:1 at
5MHz as measured at the inputs. If the source impedance
is 1kΩ, the effective stray capacitance between output and
input must have a reactance of more than (2000)(1kΩ) =
2MΩ, or less than 0.02pF. The actual interlead capacitance
between input and output pins on the LT1011 is less than
0.002pF when cut to printed circuit mount length. Additional
stray capacitance due to printed circuit traces must be
minimized by routing the output trace directly away from
input lines and, if possible, running ground traces next
to input traces to provide shielding. Additional steps to
ensure oscillation-free operation are:
1. Bypass the STROBE/BALANCE pins with a 0.01µF capacitor connected from Pin 5 to Pin 6. This eliminates stray
capacitive feedback from the output to the BALANCE
pins, which are nearly as sensitive as the inputs.
2. Bypass the negative supply (Pin 4) with a 0.1µF ceramic
capacitor close to the comparator. 0.1µF can also be
used for the positive supply (Pin 8) if the pull-up load
is tied to a separate supply. When the pull-up load is
tied directly to Pin 8, use a 2µF solid tantalum bypass
capacitor.
3. Bypass any slow moving or DC input with a capacitor (≥0.01µF) close to the comparator to reduce high
frequency source impedance.
4. Keep resistive source impedance as low as possible. If
a resistor is added in series with one input to balance
source impedances for DC accuracy, bypass it with a
capacitor. The low input bias current of the LT1011
usually eliminates any need for source resistance balancing. A 5kΩ imbalance, for instance, will create only
0.25mV DC offset.
5. Use hysteresis. This consists of shifting the input offset
voltage of the comparator when the output changes
state. Hysteresis forces the comparator to move quickly
through its linear region, eliminating oscillations by
“overdriving” the comparator under all input conditions.
Hysteresis may be either AC or DC. AC techniques do
not shift the apparent offset voltage of the comparator, but require a minimum input signal slew rate to be
effective. DC hysteresis works for all input slew rates,
but creates a shift in offset voltage dependent on the
previous condition of the input signal. The circuit shown
in Figure 1 is an excellent compromise between AC and
DC hysteresis.
15V
2µF
TANT
+
3
INPUTS
2
–
+
C1
0.003µF
8
6
LT1011
5 7
1
R2
15M
RL
OUTPUT
4
–15V
0.1µF
1011 F01
Figure 1. Comparator with Hysteresis
1011afe
8
For more information www.linear.com/LT1011
LT1011/LT1011A
Applications Information
Note that at low frequencies, the error is simply the
DC hysteresis, while at high frequencies, an additional error is created by the AC hysteresis. The high
frequency error can be reduced by reducing CH, but
lower values may not provide clean switching with very
low slew rate input signals.
Input Protection
The inputs to the LT1011 are particularly suited to general
purpose comparator applications because large differential
and/or common mode voltages can be tolerated without
damage to the comparator. Either or both inputs can be
raised 40V above the negative supply, independent of the
positive supply voltage. Internal forward biased diodes
will conduct when the inputs are taken below the negative
supply. In this condition, input current must be limited to
1mA. If very large (fault) input voltages must be accommodated, series resistors and clamp diodes should be
used (see Figure 3).
8
C8 TO C6 = 0.003µF
7
INPUT OFFSET VOLTAGE (mV)
This circuit is especially useful for general purpose
comparator applications because it does not force
any signals directly back onto the input signal source.
Instead, it takes advantage of the unique properties
of the BALANCE pins to provide extremely fast, clean
output switching even with low frequency input signals
in the millivolt range. The 0.003µF capacitor from Pin
6 to Pin 8 generates AC hysteresis because the voltage
on the BALANCE pins shifts slightly, depending on the
state of the output. Both pins move about 4mV. If one
pin (6) is bypassed, AC hysteresis is created. It is only
a few millivolts referred to the inputs, but is sufficient
to switch the output at nearly the maximum speed of
which the comparator is capable. To prevent problems
from low values of input slew rate, a slight amount of DC
hysteresis is also used. The sensitivity of the BALANCE
pins to current is about 0.5mV input referred offset for
each microampere of BALANCE pin current. The 15M
resistor tied from OUTPUT to Pin 5 generates 0.5mV DC
hysteresis. The combination of AC and DC hysteresis
creates clean oscillation-free switching with very small
input errors. Figure 2 plots input referred error versus
switching frequency for the circuit as shown.
6
5
4
3
2
OUTPUT “LO” TO “HI”
1
0
OUTPUT “HI” TO “LO”
–1
–2
(50kHz)
(5kHz)
10
100
TIME/FREQUENCY (µs)
1
1000
1011 F02
Figure 2. Input Offset Voltage vs Time to Last Transition
V+
R1**
INPUTS
D1
D2
R3*
300Ω 3
R4*
300Ω 2
R2**
D3
D4
D1 TO D4: 1N4148
*MAY BE ELIMINATED FOR IFAULT ≤ 1mA
**SELECT ACCORDING TO ALLOWABLE
FAULT CURRENT AND POWER DISSIPATION
–
8
LT1011
+
4
V–
1011 F03
Figure 3. Limiting Fault Input Currents
1011afe
For more information www.linear.com/LT1011
9
LT1011/LT1011A
Applications Information
The input resistors should limit fault current to a reasonable
value (0.1mA to 20mA). Power dissipation in the resistors must be considered for continuous faults, especially
when the LT1011 supplies are off. One final caution: lightly
loaded supplies may be forced to higher voltages by large
fault currents flowing through D1-D4.
15V
3
The response time of a comparator is typically measured
with a 100mV step and a 5mV to 10mV overdrive. Unfortunately, this does not simulate many real world situations
where the step size is typically much larger and overdrive
can be significantly less. In the case of the LT1011, step
size is important because the slew rate of internal nodes
will limit response time for input step sizes larger than
1V. At 5V step size, for instance, response time increases
from 150ns to 360ns. See the curve “Response Time vs
Input Step Size for more detail.
If response time is critical and large input signals are expected, clamp diodes across the inputs are recommended.
The slew rate limitation can also affect performance when
differential input voltage is low, but both inputs must
slew quickly. Maximum suggested common mode slew
rate is 10V/µs.
+
OUTPUT
1
6
TTL OR
CMOS DRIVE
(5V SUPPLY)
–15
3k
1011 F04
Figure 4. Typical Strobe Circuit
level inputs. A 1pF capacitor between the output and Pin
5 will greatly reduce oscillation problems without reducing strobe speed.
DC hysteresis can also be added by placing a resistor
from the output to Pin 5. See step 5 under “Preventing
Oscillation Problems.”
The pin (6) used for strobing is also one of the offset adjust
pins. Current flow into or out of Pin 6 must be kept very
low (< 0.2µA) when not strobing to prevent input offset
voltage shifts.
Output Transistor
The LT1011 output transistor is truly floating in the sense
that no current flows into or out of either the collector
or emitter when the transistor is in the “off” state. The
equivalent circuit is shown in Figure 5.
V+
Strobing
The LT1011 can be strobed by pulling current out of the
STROBE pin. The output transistor is forced to an “off”
state, giving a “hi” output at the collector (Pin 7). Currents
as low as 250µA will cause strobing, but at low strobe
currents, strobe delay will be 200ns to 300ns. If strobe
current is increased to 3mA, strobe delay drops to about
60ns. The voltage at the STROBE pin is about 150mV below
V+ at zero strobe current and about 2V below V+ for 3mA
strobe current. Do not ground the STROBE pin. It must
be current driven. Figure 4 shows a typical strobe circuit.
Note that there is no bypass capacitor between Pins 5 and
6. This maximizes strobe speed, but leaves the comparator more sensitive to oscillation problems for slow, low
10
RL
7
4
R3 and R4 limit input current to the LT1011 to less than
1mA when the input signals are held below V –. They may
be eliminated if R1 and R2 are large enough to limit fault
current to less than 1mA.
Input Slew Rate Limitations
8
–
LT1011
2
5V
I1
0.5mA
D1
D2
COLLECTOR
(OUTPUT)
Q1
R1
170Ω
V–
Q2
R2
470Ω
OUTPUT
TRANSISTOR
EMITTER
(GND PIN)
1011 F05
Figure 5. Output Transistor Circuitry
For more information www.linear.com/LT1011
1011afe
LT1011/LT1011A
Applications Information
is tied to V+, the voltage at the emitter in the “on” state is
about 2V below V+ (see curves).
In the “off” state, I1 is switched off and both Q1 and Q2
turn off. The collector of Q2 can be now held at any voltage
above V – without conducting current, including voltages
above the positive supply level. Maximum voltage above
V– is 50V for the LT1011M and 40V for the LT1011C/I.
The emitter can be held at any voltage between V+ and
V– as long as it is negative with respect to the collector.
Input Signal Range
The common mode input voltage range of the LT1011 is
about 300mV above the negative supply and 1.5V below the
positive supply, independent of the actual supply voltages
(see curve in the Typical Performance Characteristics). This
is the voltage range over which the output will respond
correctly when the common mode voltage is applied to
one input and a higher or lower signal is applied to the
remaining input. If one input is inside the common mode
range and one is outside, the output will be correct. If the
inputs are outside the common mode range in opposite
directions, the output will still be correct. If both inputs are
outside the common mode range in the same direction,
the output will not respond to the differential input; for
temperatures of 25°C and above, the output will remain
unconditionally high (collector output), for temperatures
below 25°C, the output becomes undefined.
In the “on” state, I1 is connected, turning on Q1 and Q2.
Diodes D1 and D2 prevent deep saturation of Q2 to improve
speed and also limit the drive current of Q1. The R1/R2
divider sets the saturation voltage of Q2 and provides turnoff drive. Either the collector or emitter pin can be held at
a voltage between V+ and V–. This allows the remaining
pin to drive the load. In typical applications, the emitter is
connected to V– or ground and the collector drives a load
tied to V+ or a separate positive supply.
When the emitter is used as the output, the collector is
typically tied to V + and the load is connected to ground
or V–. Note that the emitter output is phase reversed with
respect to the collector output so that the “+” and “–”
input designations must be reversed. When the collector
Typical Applications
Offset Balancing
Driving Load Referenced
to Positive Supply
R2
3k
5
2
3
+
V+
3
R1
20k
V+
6
LT1011
2
8
LT1011
+
V
1011 TA03
7
V+
2
RLOAD
INPUTS*
1
4
7
–
V++
8
–
Driving Load Referenced
to Negative Supply
3
V
8
–
7
LT1011
1
+
RLOAD
4
V
OR
GROUND
V++ CAN BE GREATER OR LESS THAN V+
1011 TA05
V
1011 TA06
*INPUT POLARITY IS REVERSED
WHEN USING PIN 1 AS OUTPUT
1011afe
For more information www.linear.com/LT1011
11
LT1011/LT1011A
Typical Applications
Strobing
2
3
Driving Ground Referred Load
V++**
V+
+
7
LT1011
–
2
6
INPUTS*
TTL
STROBE
3
V+
LT1011
+
V–
7
3
1
L1
NOTE: DO NOT GROUND STROBE PIN
2
1011 TA07
2
D2
D1
3
VOLTAGE
INPUT
+
7
LT1011
LT1011
–
OUTPUT HIGH
INSIDE “WINDOW”
AND LOW ABOVE
HIGH LIMIT OR
BELOW LOW LIMIT
1
+
7
LT1011
–
1
Crystal Oscillator
5V
10k
OUTPUT
2
85kHz
100pF
1k
8
+
50k
7
LT1011
3
GROUND OR
LOW IMPEDANCE
REFERENCE
*SEE CURVE, “RESPONSE TIME vs INPUT STEP SIZE”
7
1011 TA08
–
R1
3
LOW
LIMIT
Using Clamp Diodes to Improve Frequency Response*
CURRENT MODE
INPUT
(DAC, ETC)
RL
+
VIN
*INPUT POLARITY IS REVERSED
WHEN USING PIN 1 AS OUTPUT
**V++ MAY BE ANY VOLTAGE ABOVE V–.
PIN 1 SWINGS TO WITHIN ≈2V OF V++
1011 TA04
2
HIGH
LIMIT
8
–
4
1k
Window Detector
OUT
4
–
1
10k
1011 TA09
10k
1011 TA10
Noise Immune 60Hz Line Sync**
High Efficiency** Motor Speed Controller
5V
60Hz
INPUT
2VRMS
TO
25VRMS
R2
75k
C1
50µF
+
R1
1k
Q1
2N6667
5V
R1*
330k
3
C1
0.22µF
2
8
–
LT1011
+
4
5V
15V
R3
1k
R6
27k
7
1N4002
OUTPUT
60Hz
1
MOTOR-TACH
GLOBE 397A120-2
R2
470Ω
R4
27k
R3*
10k
MOTOR TACH
15V
1011 TA11
R5
10k
8
*INCREASE R1 FOR LARGER INPUT VOLTAGES
**LT1011 SELF OSCILLATES AT ≈60Hz CAUSING
IT TO “LOCK” ONTO INCOMING LINE SIGNAL
7
+
LT1011
1
–
2
3
C2*
0.1µF
R5
100k
R6
2k
C3
0.1µF
R7
1k
1011 TA12
R4
1k
4
*R3/C2 DETERMINES OSCILLATION
–5V TO
FREQUENCY OF CONTROLLER
–15V 0V TO 10V
**Q1 OPERATES IN SWITCH MODE
INPUT
1011afe
12
For more information www.linear.com/LT1011
LT1011/LT1011A
Typical Applications
Combining Offset Adjust and Strobe
Combining Offset Adjustment and Hystersis
V+
10k
3
2
+
RH*
2RH**
20k
5
–
V+
5k
6
LT1011
3
TTL OR CMOS
5V
2
1k
–
5
+
*HYSTERESIS IS ≈0.45mV/µA OF
CURRENT CHANGE IN RH
RL **THIS RESISTOR CAUSES HYSTERESIS
TO BE CENTERED AROUND VOS
20k
6
LT1011
7
1011 TA15
1
1011 TA13
Direct Strobe Drive When CMOS* Logic
Uses Same V + Supply as LT1011
Low Drift R/C Oscillator †
V+
3
2
+
**
8
–
2
6
LT1011
15V
C1
0.015µF
1011 TA14
3
*NOT APPLICABLE FOR TTL LOGIC
15V
8
+
1k
74HC04
×6
7
LT1011
BUFFERED
OUTPUT
4
–
1
Positive Peak Detector
15V
INPUT
***
2k
3
2
10k*
10k*
8
+
7
LT1011
2
1
–
4
10k 3
1M**
+
C1*
2µF
–
6
LT1008
+
OUTPUT
8
100pF
15V
*1% METAL FILM
10k*
**TRW TYPE MTR-5/120ppm/°C, 25k ≤ RS ≤ 200k
C1: 0.015µF = POLYSTYRENE, –120ppm/°C,
1011 TA16
±30ppm WESCO TYPE 32-P
NOTE: COMPARATOR CONTRIBUTES ≤10ppm/°C DRIFT
FOR FREQUENCIES BELOW 10kHz
†
LOW DRIFT AND ACCURATE FREQUENCY ARE
OBTAINED BECAUSE THIS CONFIGURATION
REJECTS EFFECTS DUE TO INPUT OFFSET
VOLTAGE AND BIAS CURRENT OF THE
COMPARATOR
1011 TA17
–15V
*MYLAR
**SELECT FOR REQUIRED RESET TIME CONSTANT
***INPUT POLARITY IS REVERSED WHEN USING PIN 1 AS OUTPUT
Negative Peak Detector
15V
2
1M**
INPUT
2k
3
2
8
–
LT1011
1
+
4
–15V
10k
7
+
C1*
2µF
3
–
LT1008
+
100pF
6
OUTPUT
8
1011 TA18
*MYLAR
**SELECT FOR REQUIRED RESET TIME CONSTANT
1011afe
For more information www.linear.com/LT1011
13
LT1011/LT1011A
Typical Applications
4-Digit (10,000 Count) A/D Converter
15V
ZERO
TRIM
R1
1k
1
3
R2
18k
R3
3.9k
8
4
C4
0.01µF
–15V
R4
5.6k
8
D1
D2
C1*
0.1µF
C2**
15pF
R8
3k
15V
D3
D4
R7
22Ω
5V
C5
0.01µF
+
6
LT1011
3
6
7
15V
R5
4.7k
2
2 5
LF398
5V
INPUT
0V TO 10V
R6
4.7K
7
1
–
OUTPUT = 1 COUNT
PER mV, f = 1MHz
CLOCK
1MHz
4
–15V
15V
C3
0.1µF
R11
6.8K
R10
1k
R9
FULL-SCALE
3.65k
TRIM
2N3904
LM329
R12
6.8k
C6
50pF
ALL DIODES: 1N4148
*POLYSTYRENE
**NPO
1011 TA19
START
≥12ms
Capacitance to Pulse Width Converter
TH ≥ [CMAX (pF)][1µs/pF]
TL ≥ 10 • CMAX • (1µs/pF)
D1
TTL OR CMOS
(OPERATING
ON 5V)
R2
R1 100k
5k
R3
86.6k
+
GAIN ADJ
5V
2
8
0.01µF
+
10µF†
LT1011
3
C**
6
1
–
4
7
(
)
*PW = (R2 + R3)(C) R1 + R4 , INPUT CAPACITANCE OF
R1
LT1011 IS ≈6pF. THIS IS AN OFFSET TERM.
R5
4.7k
OUTPUT
1µs/pF
** TYPICAL 2 SECTIONS OF 365pF VARIABLE
CAPACITOR WHEN USED AS SHAFT ANGLE
INDICATION
†THESE COMPONENTS MAY BE ELIMINATED IF
NEGATIVE SUPPLY IS AVAILABLE (–1V TO –15V)
D3†
+
D2†
10µF†
1011 TA20
1011afe
14
For more information www.linear.com/LT1011
LT1011/LT1011A
Typical Applications
Fast Settling Filter
100pF
1M
15V
2
1M
4.7k
VIN
3
–15V 15V
100k
2
–15V
8
3
1
100pF
1.5k
7 1
LT1011
OUTPUT
8
1µF
OFM-1A
4
–
6
LT1008C
4
4.7k
0.1µF
7
5
+
6
INPUT*
15V
15V
3
2
COMPARATORS DRIVE OPTO-COUPLED FET
“ON” WHEN DIFFERENCE BETWEEN OUTPUT
AND INPUT EXCEEDS THRESHOLD. WHEN
OUTPUT APPROACHES INPUT, THE GATE TURNS
“OFF” AND LOW PASS FILTERING OCCURS.
5k
THRESHOLD
5k
6
+
5 1
LT1011
–
*INPUT POLARITY IS REVERSED WHEN USING
PIN 1 AS OUTPUT
7
8
4
10k
–15V 15V
1011 TA21
100kHz Precision Rectifier
0.033µF
5V
AC INPUT
100Ω
5k
ZERO
CROSS
TRIM
2
3
5V
8
+
LT1011
–
1
4
5V
1k
7
5V
74C04
12k
820Ω
HP5082-2800
×4
RECTIFIED
OUTPUT
–5V
5V
–5V
1k
820Ω
74C04
–5V
12k
–5V
1011 TA23
1011afe
For more information www.linear.com/LT1011
15
LT1011/LT1011A
Schematic Diagram
OFFSET
OFFSET/STROBE
V+
5
6
8
R8
800Ω
Q6
R27
3k
R4
300Ω
R5
160Ω
2
R2
1.3k
Q10
R3
300Ω
R23
4k
Q11
Q5
Q31
INPUT
(+)
R1
1.3k
R9
800Ω
D1 D2
Q30
Q29
Q12
R6
3.2k
R7
3.2k
D4
D6
Q13
Q7
Q8
Q14
Q3
INPUT
(–)
Q9 Q19
3
Q27
D5
D7
Q26
Q23
R26
1.6k
R19
500Ω
7
R12
470Ω
R17
200Ω
Q21
R20
940Ω
Q22
R25
1.6k
OUTPUT
Q15
Q4
Q2
Q25
R11
170Ω
Q20
R22
200Ω
Q1
Q28
R10
4k
R21
960Ω
R18
275Ω
R16 Q24
800Ω
Q16
R24
400Ω
R15
700Ω
R13
4Ω
1
Q18
GND
R14
4.8k
D3
Q17
4
V–
1011 SD
1011afe
16
For more information www.linear.com/LT1011
LT1011/LT1011A
Package Description
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
H Package
8-Lead TO-5 Metal Can (.230 Inch PCD)
(Reference LTC DWG # 05-08-1321)
0.040
(1.016)
MAX
OBSOLETE PACKAGE
0.335 – 0.370
(8.509 – 9.398)
DIA
0.305 – 0.335
(7.747 – 8.509)
0.027 – 0.045
(0.686 – 1.143)
45°TYP
0.050
(1.270)
MAX
SEATING
PLANE
0.165 – 0.185
(4.191 – 4.699)
GAUGE
PLANE
0.010 – 0.045*
(0.254 – 1.143)
PIN 1
0.028 – 0.034
(0.711 – 0.864)
0.230
(5.842)
TYP
REFERENCE
PLANE
0.500 – 0.750
(12.700 – 19.050)
H8 (TO-5) 0.230 PCD 1197
0.110 – 0.160
(2.794 – 4.064)
INSULATING
STANDOFF
0.016 – 0.021**
(0.406 – 0.533)
*LEAD DIAMETER IS UNCONTROLLED BETWEEN THE REFERENCE PLANE
AND 0.045" BELOW THE REFERENCE PLANE
0.016 – 0.024
**FOR SOLDER DIP LEAD FINISH, LEAD DIAMETER IS
(0.406 – 0.610)
J8 Package
8-Lead CERDIP (Narrow .300 Inch, Hermetic)
(Reference LTC DWG # 05-08-1110)
OBSOLETE PACKAGE
CORNER LEADS OPTION
(4 PLCS)
0.023 – 0.045
(0.584 – 1.143)
HALF LEAD
OPTION
0.045 – 0.068
(1.143 – 1.727)
FULL LEAD
OPTION
0.005
(0.127)
MIN
0.405
(10.287)
MAX
8
7
6
5
0.025
(0.635)
RAD TYP
0.220 – 0.310
(5.588 – 7.874)
1
0.300 BSC
(0.762 BSC)
2
3
4
0.200
(5.080)
MAX
0.015 – 0.060
(0.381 – 1.524)
0.008 – 0.018
(0.203 – 0.457)
0° – 15°
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE
OR TIN PLATE LEADS
0.045 – 0.065
(1.143 – 1.651)
0.014 – 0.026
(0.360 – 0.660)
0.100
(2.54)
BSC
0.125
3.175
MIN
J8 1298
1011afe
For more information www.linear.com/LT1011
17
LT1011/LT1011A
Package Description
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
N8 Package
8-Lead PDIP (Narrow .300 Inch)
(Reference LTC DWG # 05-08-1510)
.300 – .325
(7.620 – 8.255)
.045 – .065
(1.143 – 1.651)
.065
(1.651)
TYP
.008 – .015
(0.203 – 0.381)
(
+.035
.325 –.015
+0.889
8.255
–0.381
)
.400*
(10.160)
MAX
.130 ± .005
(3.302 ± 0.127)
8
7
6
5
1
2
3
4
.255 ± .015*
(6.477 ± 0.381)
.120
(3.048) .020
MIN
(0.508)
MIN
.018 ± .003
(0.457 ± 0.076)
.100
(2.54)
BSC
N8 1002
NOTE:
1. DIMENSIONS ARE
INCHES
MILLIMETERS
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm)
S8 Package
8-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610)
.189 – .197
(4.801 – 5.004)
NOTE 3
.050 BSC
.045 ±.005
.010 – .020
× 45°
(0.254 – 0.508)
.008 – .010
(0.203 – 0.254)
.245
MIN
NOTE:
1. DIMENSIONS IN
.030 ±.005
TYP
0°– 8° TYP
.016 – .050
(0.406 – 1.270)
.160 ±.005
.053 – .069
(1.346 – 1.752)
.014 – .019
(0.355 – 0.483)
TYP
INCHES
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
8
7
6
5
.004 – .010
(0.101 – 0.254)
.050
(1.270)
BSC
.150 – .157
(3.810 – 3.988)
NOTE 3
.228 – .244
(5.791 – 6.197)
1
2
3
4
SO8 0303
RECOMMENDED SOLDER PAD LAYOUT
1011afe
18
For more information www.linear.com/LT1011
LT1011/LT1011A
Revision History
(Revision history begins at Rev D)
REV
DATE
DESCRIPTION
D
10/12
Update to Product Description
1
Addition of Order Information
2, 3
E
4/13
PAGE NUMBER
Addition of Pin Function Information
7
Correction to Positive Peak Detector Circuit
13
Correction to Pin Function descriptions
2, 7
Correction to Order Information and Obsolete Packages
3
Correction to Graphs:
Response Time—Collector Output – high to low
Response Time Using GND Pin as Output – low to high
Response Time Using GND Pin as Output – high to low
Output Saturation—Ground Output
5, 6
Correction to input pin polarity
10, 13, 15
1011afe
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection
of its circuits
as described
herein will not infringe on existing patent rights.
For more
information
www.linear.com/LT1011
19
LT1011/LT1011A
Typical Application
10Hz to 100kHz Voltage to Frequency Converter
R7
4.7k
R4
1M
15V
C1
0.002µF
POLYSTYRENE
R1
4.7k
INPUT
0V TO 10V
LT1009
2.5V
15V
R2
5k
FULL-SCALE
R3
TRIM
8.06k
R5
2k
15V
3
C2
0.68µF
15V
R16
50k
10Hz TRIM
15V
R17†
22M
2
R6
2k
LINEARITY ≈0.01%
8
–
LT1011
+
R8
4.7k
7
1
–15V
4
1.5µs
6
4.4V
–15V
0.002µF
–15V
15V
–15V
R11
20k
10pF
ALL DIODES 1N4148
TRANSISTORS 2N3904
*USED ONLY TO GUARANTEE
START-UP
†
MAY BE INCREASED FOR BETTER
10Hz TRIM RESOLUTION
R15
22k
R14
1k
Q1*
15V
R9
5k
Q2
R12
100k
+
2µF
TTL OUTPUT
10HZ TO 100kHz
1.5µs
R10
2.7k
1011 TA22
R13
620k
–15V
Related Parts
PART NUMBER
DESCRIPTION
COMMENTS
LT1016
UltraFast™ Precision Comparator
Industry Standard 10ns Comparator
LT1116
12ns Single Supply Ground-Sensing Comparator
Single Supply Version of the LT1016
LT1394
UltraFast Single Supply Comparator
7ns, 6mA Single Supply Comparator
LT1671
60ns, Low Power Comparator
450µA Single Supply Comparator
UltraFast is a trademark of Linear Technology Corporation.
1011afe
20 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
For more information www.linear.com/LT1011
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com/LT1011
LT 0413 REV E • PRINTED IN USA
 LINEAR TECHNOLOGY CORPORATION 1991