Vishay M55342K11B1C100CWSV Qpl mil-prf-55342 qualified thin film resistor chip Datasheet

E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
QPL MIL-PRF-55342 Qualified
Thin Film Resistor, Surface Mount Chip
FEATURES
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing.
CONSTRUCTION
Passivation
Resistor Film
Solder
Coating
• Established reliability, "S" and "V" failure rate level
(10 ppm), C = 2
• High purity alumina substrate
• Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+150 °C operating conditions
• Very low noise and voltage coefficient
(< -25 dB, 0.5 ppm/V)
• Non-inductive
• Laser-trimmed tolerances ± 0.1 %
• Wraparound resistance less than 0.010  typical
• In-lot tracking less than 5 ppm/°C
• Complete MIL-testing available in-house
• Antistatic waffle pack or tape and reel packaging available
• Military/aerospace/QPL
TYPICAL PERFORMANCE
ABSOLUTE
Nickel Barrier
High Purity
Alumina Substrate
Adhesion Layer
TCR
25
TOL.
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Tamelox resistor film (passivated nichrome)
10  to 6.19 M
± 25 ppm/°C to ± 300 ppm/°C
± 0.1 % to ± 10 %
R ± 0.02 %
0.1 ppm/V
30 V to 200 V
-55 °C to +150 °C
-55 °C to +150 °C
< - 25 dB
R ± 0.01 %
CONDITIONS
-55 °C to +125 °C
+25 °C
2000 h at +70 °C
1 year at +25 °C
COMPONENT RATINGS
CASE SIZE
POWER
RATING
(mW)
50
125
200
150
225
150
250
800
1000
500
50
100
RESISTANCE RANGE () BY CHARACTERISTICS TOLERANCE
WORKING
VOLTAGE
E
E
H, K, L, M
H, K, L, M
(V)
(0.1 %, 0.25 %, 0.5 %)
(1 %, 2 %, 5 %)
(0.1 %, 0.25 %, 0.5 %)
(1 %, 2 %, 5 %)
40
49.9 to 150K
49.9 to 150K
20 to 150K
20 to 150K
40
49.9 to 301K
49.9 to 301K
20 to 301K
20 to 301K
75
49.9 to 649K
49.9 to 649K
10 to 649K
10 to 649K
125
49.9 to 1.69M
49.9 to 1.69M
10 to 1.69M
10 to 1.69M
175
49.9 to 3.16M
49.9 to 3.16M
10 to 3.16M
10 to 3.16M
50
49.9 to 475K
49.9 to 475K
10 to 475K
10 to 475K
100
49.9 to 1.5M
49.9 to 1.5M
10 to 1.5M
10 to 1.5M
150
49.9 to 4.02M
49.9 to 4.02M
10 to 4.02M
10 to 4.02M
200
49.9 to 6.19M
49.9 to 6.19M
10 to 6.19M
10 to 6.19M
75
49.9 to 1M
49.9 to 1M
49.9 to 1M
49.9 to 1M
30
49.9 to 100K
49.9 to 100K
20 to 100K
20 to 100K
50
49.9 to 258K
49.9 to 261K
10 to 258K
10 to 261K
M55342/01
M55342/02
M55342/03
M55342/04
M55342/05
M55342/06
D55342/07
M55342/08
M55342/09
M55342/10
M55342/11
M55342/12
Note
• Values listed are a guide, refer to MIL spec for value/tolerance allowance
Revision: 04-Nov-14
Document Number: 60018
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
DIMENSIONS in inches
D
W
T
E
L
CASE SIZE
TERM.
L
W
T
D
E
M55342/01
B
0.055 ± 0.006
0.025 ± 0.005
0.010 to 0.030
0.010 ± 0.005
0.015 ± 0.005
M55342/02
B
0.055 ± 0.006
0.050 ± 0.005
0.012 to 0.033
0.010 ± 0.005
0.015 ± 0.005
M55342/03
B
0.105 ± 0.007
0.050 ± 0.005
0.015 to 0.033
0.015 ± 0.005
0.015 ± 0.005
M55342/04
B
0.155 ± 0.007
0.050 ± 0.005
0.015 to 0.033
0.015 ± 0.005
0.015 ± 0.005
M55342/05
B
0.230 ± 0.007
0.075 ± 0.005
0.015 to 0.033
0.020 ± 0.005
0.020 ± 0.005
0.016 ± 0.008
0.015 ± 0.005
M55342/06
B
0.080 ± 0.006
0.050 ± 0.005
0.015 to 0.033
D55342/07
B
0.126 ± 0.008
0.063 ± 0.005
0.015 to 0.033
M55342/08
B
0.209 + 0.009/- 0.018
0.098 ± 0.005
0.015 to 0.033
0.020 ± 0.005
M55342/09
B
0.259 + 0.009/- 0.015
0.124 ± 0.005
0.015 to 0.033
0.020 ± 0.005
0.020 ± 0.005
M55342/10
B
0.105 ± 0.007
0.100 ± 0.005
0.015 to 0.033
0.015 ± 0.005
0.015 ± 0.005
M55342/11
B
0.040 ± 0.005
0.025 ± 0.005
0.010 to 0.030
0.010 ± 0.005
0.015 ± 0.005
M55342/12
B
0.064 ± 0.006
0.032 ± 0.005
0.010 to 0.033
0.012 ± 0.005
0.015 ± 0.005
0.020 + 0.005/- 0.010 0.020 + 0.005/- 0.010
0.020 ± 0.005
ENVIRONMENTAL TESTS
MIL-PRF-55342 LIMITS
(R ±)
VISHAY PERFORMANCE
(R ±)
Thermal Shock
0.1 %
0.020 %
Low Temperature Operation
0.1 %
0.025 %
Short Time Overload
0.1 %
0.050 %
High Temperature Exposure
0.1 %
0.009 %
Resistance to Bonding
0.2 %
0.006 %
Moisture Resistance
0.2 %
0.004 %
± 25 ppm/°C
< 15 ppm/°C
Life (2000 h at + 70 °C)
0.5 %
0.02 %
Life (10 000 h at + 70 °C)
2.0 %
0.04 %
ENVIRONMENTAL TEST
TCR
MECHANICAL SPECIFICATIONS
Resistive Element
Tamelox
Substrate Material
Alumina
Chip Terminations
Solder over nickel
Fused Solder
Revision: 04-Nov-14
FSCM CAGE # - 57489
Plated solder 90/10
Document Number: 60018
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
Percent of Rated Wattage
DERATING
100
80
60
40
20
0
-75
-50
-25
0
25
50
75
100
125
150
175
Ambient Temperature °C
GLOBAL PART NUMBER INFORMATION
New Global Part Numbering: M55342E06B1C00RTS
M
5
5
3
GLOBAL
TCR
MODEL CHARACTERISTIC
M55342
or
D55342
(/07 size
only)
E = 25 ppm/°C
H = 50 ppm/°C
K = 100 ppm/°C
L = 200 ppm/°C
M = 300 ppm/°C
4
CASE
SIZE
01 = 0502
02 = 0505
03 = 1005
04 = 1505
05 = 2208
06 = 0705
07 = 1206
08 = 2010
09 = 2512
10 = 1010
11 = 0402
12 = 0603
2
E
0
6
TERMINATION
B = Solderable
B
1
C
0
0
FAILURE
RATE
OHMIC VALUE
M
N
P
T
S
V
THIN FILM
CODE (1)
PACKAGING
Three digits and a letter. Letter M = 1.0 %
identifies tolerance, acts as per 1000 h
multiplier and decimal locator. P = 0.1 %
per 1000 h
MULTIPLIER
R = 0.01 %
Tolerance 1  1 k 1 M per 1000 h
U = 0.01 %
0.1 %
A
B
C
per 1000 h(3)
0.25 %
R
U
V
S = 0.001 %
per 1000 h
0.5 %
W
Y
Z
V = 0.001 %
1%
D
E
F
per 1000 h (3)
2%
G
H
T
C = Non ER
version
5%
J
K
L
10 %
R
Standard Packaging:
V
BS = BULK
for
100 min., 1 mult
K, L and M
WS =WAFFLE
TCR
100 min., 1 mult
W/tolerance
W0 =WAFFLE 
1%
100 min.,100 mult
M = Part
TAPE AND REEL
marked (2)
T0 = 100 min., 100 mult
T1 = 1000 min., 1000 mult
T3 = 300 min., 300 mult
T5 = 500 min., 500 mult
TF = Full reel ( 2K, 4K, or
5K dependent on case
size ) per tape and reel
document 60034
TS = 100 min., 1 mult
Special Packaging:
WAFFLE
WI = 100 min., 1 mult
(item single lot date code)
WP =100 min., 1 mult
(package unit single lot 
date code)
TAPE AND REEL
TI = 100 min., 1 mult
(item single lot date code)
TP = 100 min., 1 mult
(package unit single lot 
date code)
Historical Part Number example: M55342K06B5E60R (for reference purposes only)
M55342
K
06
B
5E60
R
SERIES
TCR
CHARACTERISTIC
CASE SIZE
TERMINATION
VALUE AND
TOLERANCE
FAILURE RATE
Notes
(1) Only add a V at the end of part number to specify Vishay Dale Thin Film for K, L and M TCR and tolerance 1 % and higher.
(2) Option 1 marking only. Case sizes 01, 02, 11, and 12 not available due to size.
(3) Failure Rate U and V require Group A and B testing on a Production Lot Basis.
Revision: 04-Nov-14
Document Number: 60018
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000
Similar pages