ONSEMI NCP600SN150T1G

NCP600
High Performance
Low−Power, LDO Regulator
with Enable
The NCP600 provides 150 mA of output current at fixed voltage
options, or an adjustable output voltage from 5.0 V down to 1.250 V. It
is designed for portable battery powered applications and offers high
performance features such as low power operation, fast enable
response time, and low dropout.
The device is designed to be used with low cost ceramic capacitors
and is packaged in the TSOP−5/SOT23−5.
http://onsemi.com
5
1
TSOP−5
SN SUFFIX
CASE 483
Features
• Output Voltage Options:
•
•
•
•
•
•
•
•
Adjustable, 1.5 V, 1.8 V, 2.8 V, 3.0 V, 3.3 V, 5.0 V
Ultra−Low Dropout Voltage of 150 mV at 150 mA
Adjustable Output by External Resistors from 5.0 V down to 1.250 V
Fast Enable Turn−on Time of 15 ms
Wide Supply Voltage Range Operating Range
Excellent Line and Load Regulation
High Accuracy up to 1.5% Output Voltage Tolerance over All
Operating Conditions
Typical Noise Voltage of 50 mVrms without a Bypass Capacitor
Pb−Free Package is Available
Typical Applications
•
•
•
•
MARKING DIAGRAM
5
xxx AYWG
G
1
xxx
A
Y
W
G
= Specific Device Code
= Assembly Location
= Year
= Work Week
= Pb−Free Package
(Note: Microdot may be in either location)
SMPS Post−Regulation
Hand−held Instrumentation
Noise Sensitive Circuits – VCO, RF Stages, etc.
Camcorders and Cameras
PIN CONNECTIONS
VOUT
VIN
Fixed Voltage Only
Driver w/
Current Limit
+
−
1
GND
2
ENABLE
3
5 Vout
4 ADJ/NC*
(Top View)
* ADJ − Adjustable Version
* NC − Fixed Voltage Version
+
1.25 V
−
GND
Vin
Thermal
Shutdown
ORDERING INFORMATION
ADJ
Adjustable Version Only
See detailed ordering and shipping information in the
package dimensions section on page 12 of this data sheet.
ENABLE
Figure 1. Simplified Block Diagram
© Semiconductor Components Industries, LLC, 2006
September, 2006 − Rev. 3
1
Publication Order Number:
NCP600/D
NCP600
PIN FUNCTION DESCRIPTION
Pin No.
Pin Name
1
Vin
Description
2
GND
3
ENABLE
The Enable Input places the device into low−power standby when pulled to logic low (< 0.4 V). Connect to Vin
if the function is not used.
4
ADJ/NC
Output Voltage Adjust Input (Adjustable Version), No Connection (Fixed Voltage Versions) (Note 1)
5
Vout
Positive Power Supply Input
Power Supply Ground; Device Substrate
Regulated Output Voltage
MAXIMUM RATINGS (Voltages are with respect to device substrate.)
Rating
Symbol
Value
Unit
−
−0.3 to 6.0
V
ISC
Infinite
−
TJ(MAX)
+150
°C
Tstg
−65 to +150
°C
Voltage at Any Pin
Output Short Circuit Duration (Note 2)
Operating Junction Temperature
Storage Temperature
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. True no connect. Printed circuit board traces are allowable.
2. Internally protected by thermal shutdown circuitry.
ATTRIBUTES
Characteristic
ESD Capability
Value
Human Body Model
Machine Model
Moisture Sensitivity
Package Thermal Resistance
3.5 kV
400 V
MSL1/260
Junction−to−Ambient, RqJA
http://onsemi.com
2
250 °C/W
NCP600
ELECTRICAL CHARACTERISTICS
(Vin = 1.750 V, Vout = 1.250 V, Cin = Cout =1.0 mF, −40°C ≤ TJ ≤ 125°C, Figure 2, unless otherwise specified.) (Note 3)
Characteristic
Symbol
Test Conditions
Min
Typ
Max
Unit
1.231
(−1.5%)
1.250
1.269
(+1.5%)
V
−
−
−
62
55
38
−
−
−
Regulator Output (Adjustable Voltage Version)
Output Voltage
Vout
Iout = 1.0 mA to 150 mA
Vin = 1.75 V to 6.0 V,
Vout = ADJ
Ripple Rejection
(Vin = Vout + 1.0 V + 0.5 Vp−p)
RR
Iout = 1.0 mA to 150 mA
f = 120 Hz
f = 1.0 kHz
f = 10 kHz
dB
Line Regulation
Regline
Vin = 1.750 V to 6.0 V,
Iout = 1.0 mA
−
1.0
10
mV
Load Regulation
Regload
Iout = 1.0 mA to 150 mA
−
2.0
15
mV
f = 10 Hz to 100 kHz
−
50
−
mVrms
300
550
800
mA
−
−
−
−
−
175
150
125
100
75
250
225
175
150
125
1.470
1.764
2.744
2.940
3.234
4.900 (−2%)
1.500
1.530
1.836
2.856
3.060
3.366
5.100 (+2%)
−
−
−
62
55
38
−
−
−
−
1.0
10
−
−
−
−
−
−
2.0
2.0
2.0
2.0
2.0
2.0
20
25
30
30
30
30
−
50
−
mVrms
300
550
800
mA
−
−
−
−
−
−
150
125
75
75
75
75
225
175
125
125
125
125
Output Noise Voltage
Vn
Output Short Circuit Current
Isc
Dropout Voltage
Vout = 1.25 V
Vout = 1.5 V
Vout = 1.8 V
Vout = 2.5 V
Vout ≥ 2.8 V
VDO
Measured at: Vout – 2.0%,
Iout = 150 mA, Figure 3
mV
Regulator Output (Fixed Voltage Version)
(Vin = Vout + 0.5 V, Cin = Cout =1.0 mF, −40°C ≤ TJ ≤ 125°C, Figure 4, unless otherwise specified.) (Note 3)
Output Voltage
1.5 V Option
1.8 V Option
2.8 V Option
3.0 V Option
3.3 V Option
5.0 V Option
Vout
Iout = 1.0 mA to 150 mA
Vin = (Vout + 0.5 V) to 6.0 V
Ripple Rejection
(Vin = Vout + 1.0 V + 0.5 Vp−p)
RR
Iout = 1.0 mA to 150 mA
f = 120 Hz
f = 1.0 kHz
f = 10 kHz
Line Regulation
Regline
Vin = 1.750 V to 6.0 V,
Iout = 1.0 mA
Load Regulation
1.5 V Option
1.8 V Option
2.8 V Option
3.0 V Option
3.3 V Option
5.0 V Option
Regload
Iout = 1.0 mA to 150 mA
Output Noise Voltage
Vn
Output Short Circuit Current
Isc
Dropout Voltage
1.5 V Option
1.8 V Option
2.8 V Option
3.0 V Option
3.3 V Option
5.0 V Option
VDO
f = 10 Hz to 100 kHz
Measured at: Vout – 2.0%
V
dB
mV
mV
V
3. Designed to meet these characteristics over the stated voltage and temperature recommended operating ranges, though may not be 100%
parametrically tested in production.
4. Guaranteed by design.
http://onsemi.com
3
NCP600
ELECTRICAL CHARACTERISTICS (Vin = 1.750 V, Vout = 1.250 V (adjustable version)), (Vin = Vout + 0.5 V (fixed version)),
Cin = Cout =1.0 mF, −40°C ≤ TJ ≤ 125°C, Figure 2, unless otherwise specified.) (Note 5)
Characteristic
Symbol
Test Conditions
Min
Typ
Max
Unit
−
0.01
1.0
mA
−
−
−
−
−
−
−
100
135
140
140
140
145
145
135
170
175
175
175
180
180
General
Ground Current
ISTBY
ENABLE = 0 V, Vin = 6 V
−40°C ≤ TJ ≤ 85°C
Ground Current
Adjustable Option
1.5 V Option
1.8 V Option
2.8 V Option
3.0 V Option
3.3 V Option
5.0 V Option
IGND
ENABLE = 0.9 V,
Iout = 1.0 mA to 150 mA
Thermal Shutdown Temperature (Note 6)
TSD
150
175
200
°C
Thermal Shutdown Hysteresis
TSH
−
10
−
°C
ADJ Input Bias Current
IADJ
−0.75
−
0.75
mA
mA
Chip Enable
ENABLE Input Threshold Voltage
V
Vth(EN)
Voltage Increasing, Logic High
0.9
Voltage Decreasing, Logic Low
Enable Input Bias Current (Note 6)
IEN
−
−
−
−
0.4
−
3.0
100
−
−
−
−
−
−
−
15
15
15
15
15
15
30
25
25
25
25
25
25
50
nA
Timing
Output Turn On Time
Adjustable Option
1.5 V Option
1.8 V Option
2.8 V Option
3.0 V Option
3.3 V Option
5.0 V Option
tEN
ENABLE = 0 V to Vin
ms
5. Designed to meet these characteristics over the stated voltage and temperature recommended operating ranges, though may not be 100%
parametrically tested in production.
6. Guaranteed by design.
http://onsemi.com
4
NCP600
5
1
VIN
CIN
2
4
3
ENABLE
VOUT
COUT
Figure 2. Typical Application Circuit for Vout = 1.250 V
(Adjustable Version)
5
1
VIN
CIN
2
R1
3
ENABLE
VOUT
COUT
4
R2
Figure 3. Typical Application Circuit for Adjustable Vout
5
1
VIN
CIN
2
3
VOUT
COUT
4
Figure 4. Typical Application Circuit
(Fixed Voltage Version)
http://onsemi.com
5
NCP600
TYPICAL CHARACTERISTICS
1.260
1.260
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
1.256
Iout = 1.0 mA
1.252
Iout = 150 mA
1.248
Vin = Vout + 0.5 V
Vout = ADJ
1.244
1.240
−40 −20
0
20
40
60
80
100
1.248
Iout = 150 mA
Vin = 6.0 V
Vout = ADJ
1.244
−15
10
35
60
85
110 125
TEMPERATURE (°C)
Figure 5. Output Voltage vs. Temperature
(Vin = Vout + 0.5 V)
Figure 6. Output Voltage vs. Temperature
(Vin = 6.0 V)
1.500
Vout, OUTPUT VOLTAGE (V)
Iout = 1.0 mA
OUTPUT VOLTAGE (V)
1.490
Iout = 150 mA
1.485
1.480
−15
10
35
60
85
Iout = 1.0 mA
1.495
1.490
Iout = 150 mA
1.485
1.480
1.475
−40
110 125
−15
10
35
60
85
110 125
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 7. Output Voltage vs. Temperature
(1.5 V Fixed Output, Vin = 2 V)
Figure 8. Output Voltage vs. Temperature
(1.5 V Fixed Output, Vin = 6 V)
3.005
3.005
Iout = 1.0 mA
2.995
Iout = 1.0 mA
3.000
OUTPUT VOLTAGE (V)
3.000
OUTPUT VOLTAGE (V)
1.252
TEMPERATURE (°C)
1.495
Iout = 150 mA
2.990
2.985
2.980
2.975
−40
Iout = 1.0 mA
1.240
−40
120
1.500
1.475
−40
1.256
2.995
2.990
Iout = 150 mA
2.985
2.980
2.975
−15
10
35
60
85
110 125
2.970
−40
TEMPERATURE (°C)
−15
10
35
60
85
110 125
TEMPERATURE (°C)
Figure 9. Output Voltage vs. Temperature
(3.0 V Fixed Output, Vin = 3.5 V)
Figure 10. Output Voltage vs. Temperature
(3.0 V Fixed Output, Vin = 6 V)
http://onsemi.com
6
NCP600
TYPICAL CHARACTERISTICS
5.000
5.000
Iout = 1.0 mA
Iout = 1.0 mA
4.995
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
4.995
4.990
Iout = 150 mA
4.985
4.980
4.975
4.970
4.990
4.985
Iout = 150 mA
4.980
4.975
4.970
4.965
−40
−15
10
35
60
110 125
85
4.965
−40
−15
10
TEMPERATURE (°C)
85
110 125
Figure 12. Output Voltage vs. Temperature
(5.0 V Fixed Output, Vin = 6 V)
250
250
Vout = ADJ
Iout = 150 mA
DROPOUT VOLTAGE (mV)
Iout = 150 mA
200
150
100
Iout = 50 mA
50
0
−40 −20
6.0
5.5
5.0
Iout = 1.0 mA
0
20
40
60
80
100
Vout = 1.25 V
200
1.50 V
1.80 V
150
2.80 V
100
3.00 V
50
5.00 V
0
−40 −20
120
0
20
40
60
80
100
120
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 13. Dropout Voltage vs. Temperature
(Over Current Range)
Figure 14. Dropout Voltage vs. Temperature
(Over Output Voltage)
800
Iout = 0 mA
Cout = 1.0 mF
TA = 25°C
ENABLE = Vin
4.5
4.0
5.0 V
3.3 V
3.0 V
3.5
3.0
ENABLE THRESHOLD (mV)
DROPOUT VOLTAGE (mV)
60
TEMPERATURE (°C)
Figure 11. Output Voltage vs. Temperature
(5.0 V Fixed Output, Vin = 5.5 V)
OUTPUT VOLTAGE (V)
35
2.80 V
2.5
2.0
1.80 V
1.5 V
1.5
1.0
1.25 V
0.5
0
0
1.0
2.0
3.0
4.0
5.0
750
Enable Increasing
700
Enable Decreasing
650
Vin = 5.5 V
600
−40
6.0
−15
10
35
60
85
110 125
INPUT VOLTAGE (V)
TEMPERATURE (°C)
Figure 15. Output Voltage vs. Input Voltage
Figure 16. Enable Threshold vs. Temperature
http://onsemi.com
7
NCP600
TYPICAL CHARACTERISTICS
6.0
GROUND CURRENT (mA)
GROUND CURRENT (mA)
154
5.0
4.0
3.0
2.0
ENABLE = 0 V
1.0
146
−15
10
35
60
85
110
130
122
114
Vout = 5.0 V
Iout = 1.0 mA
106
Iout = 150 mA
ENABLE = 0.9 V
90
−40 −20
125
Iout = 150 mA
Vout = 1.25 V
138
98
0
−40
0
20
40
60
80
100
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 17. Ground Current (Sleep Mode) vs.
Temperature
Figure 18. Ground Current (Run Mode) vs.
Temperature
120
106
160
3.0 V
105
1.5 V
5.0 V
3.3 V
GROUND CURRENT (mA)
2.8 V
140
120
1.8 V
1.25 V
100
80
60
40
104
103
102
101
100
Vout = ADJ
Vin = 1.75 V
99
20
98
0
0
1.0
2.0
3.0
4.0
5.0
0
6.0
25
50
75
100
125
150
Vin, INPUT VOLTAGE (V)
OUTPUT CURRENT (mA)
Figure 19. Ground Current vs. Input Voltage
Figure 20. Ground Current vs. Output Current
400
ADJ INPUT BIAS CURRENT (nA)
GROUND CURRENT (mA)
Iout = 1.0 mA
300
200
100
0
−40
−20
0
20
40
60
80
100
TEMPERATURE (°C)
Figure 21. ADJ Input Bias Current vs.
Temperature
http://onsemi.com
8
120
NCP600
650
700
600
CURRENT LIMIT (mA)
OUTPUT SHORT CIRCUIT CURRENT (mA)
TYPICAL CHARACTERISTICS
600
550
500
500
400
300
200
100
450
−40 −20
0
0
20
40
60
80
100
120
0
4.0
5.0
Figure 23. Current Limit vs. Input Voltage
6.0
5.0
LOAD REGULATION (mV)
LINE REGULATION (mV)
3.0
Figure 22. Output Short Circuit Current vs.
Temperature
3.0
2.0
1.0
Vin = (Vout + 0.5 V) to 6.0 V
Iout = 1.0 mA
0
−40 −20
0
20
40
60
80
100
4.0
3.0
2.0
1.0
Iout = 1.0 mA to 150 mA
0
−40
120
−15
10
35
85
60
110 125
TEMPERATURE (°C)
Figure 25. Load Regulation vs. Temperature
POWER SUPPLY RIPPLE REJECTION (dB)
TEMPERATURE (°C)
Figure 24. Line Regulation vs. Temperature
45
OUTPUT TURN ON TIME (mS)
2.0
Vin, INPUT VOLTAGE (V)
4.0
40
35
5.0 V
30
25
3.0 V
20
15
1.0
TEMPERATURE (°C)
1.5 V
1.25 V (ADJ)
10
−40 −20
0
20
40
60
80
100
120
80
1.25 V
70
60
3.3 V
50
40
5.0 V
30
Vin = Vout + 1.0 V
Vripple = 0.5 Vp−p
Cout = 1.0 mF
Iout = 1.0 mA to 150 mA
20
10
0
0.1
1.0
10
100
TEMPERATURE (°C)
FREQUENCY (kHz)
Figure 26. Output Turn On Time vs.
Temperature
Figure 27. Power Supply Ripple Rejection vs.
Frequency
http://onsemi.com
9
NCP600
TYPICAL CHARACTERISTICS
OUTPUT CAPACITOR ESR (W)
10
Vout = 5.0 V
Unstable Region
Vout = 1.25 V
1.0
Stable Region
0.1
Cout = 1.0 mF to 10 mF
TA = −40°C to 125°C
Vin = up to 6.0 V
0.01
0
25
50
75
100
125
150
OUTPUT CURRENT (mA)
Figure 28. Output Stability with Output
Capacitor ESR over Output Current
Vout = 1.25 V
Figure 29. Load Transient Response (1.0 mF)
Vout = 1.25 V
Figure 30. Load Transient Response (10 mF)
http://onsemi.com
10
NCP600
DEFINITIONS
Load Regulation
Line Regulation
The change in output voltage for a change in output load
current at a constant temperature.
The change in output voltage for a change in input voltage.
The measurement is made under conditions of low
dissipation or by using pulse techniques such that the
average junction temperature is not significantly affected.
Dropout Voltage
The input/output differential at which the regulator output
no longer maintains regulation against further reductions in
input voltage. Measured when the output drops 2% below its
nominal. The junction temperature, load current, and
minimum input supply requirements affect the dropout level.
Line Transient Response
Typical output voltage overshoot and undershoot
response when the input voltage is excited with a given
slope.
Output Noise Voltage
Load Transient Response
This is the integrated value of the output noise over a
specified frequency range. Input voltage and output load
current are kept constant during the measurement. Results
are expressed in mVrms or nV √ Hz.
Typical output voltage overshoot and undershoot
response when the output current is excited with a given
slope between no−load and full−load conditions.
Ground Current
Internal thermal shutdown circuitry is provided to protect
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated at typically 175°C,
the regulator turns off. This feature is provided to prevent
failures from accidental overheating.
Thermal Protection
Ground Current is the current that flows through the
ground pin when the regulator operates without a load on its
output (IGND). This consists of internal IC operation, bias,
etc. It is actually the difference between the input current
(measured through the LDO input pin) and the output load
current. If the regulator has an input pin that reduces its
internal bias and shuts off the output (enable/disable
function), this term is called the standby current (ISTBY.)
Maximum Package Power Dissipation
The power dissipation level at which the junction
temperature reaches its maximum operating value.
APPLICATIONS INFORMATION
The NCP600 series regulator is self−protected with
internal thermal shutdown and internal current limit. Typical
application circuits are shown in Figures 2 and 3.
output, there is no resistor divider. If the part is enabled
under no−load conditions, leakage current through the pass
transistor at junction temperatures above 85°C can approach
several microamperes, especially as junction temperature
approaches 150°C. If this leakage current is not directed into
a load, the output voltage will rise up to a level
approximately 20 mV above nominal.
The NCP600 contains an overshoot clamp circuit to
improve transient response during a load current step
release. When output voltage exceeds the nominal by
approximately 20 mV, this circuit becomes active and
clamps the output from further voltage increase. Tying the
ENABLE pin to Vin will ensure that the part is active
whenever the supply voltage is present, thus guaranteeing
that the clamp circuit is active whenever leakage current is
present.
When the NCP600 adjustable regulator is disabled, the
overshoot clamp circuit becomes inactive and the pass
transistor leakage will charge any capacitance on Vout. If no
load is present, the output can charge up to within a few
millivolts of Vin. In most applications, the load will present
some impedance to Vout such that the output voltage will be
inherently clamped at a safe level. A minimum load of
10 mA is recommended.
Input Decoupling (Cin)
A ceramic or tantalum 1.0 mF capacitor is recommended
and should be connected close to the NCP600 package.
Higher capacitance and lower ESR will improve the overall
line transient response.
Output Decoupling (Cout)
The NCP600 is a stable component and does not require
a minimum Equivalent Series Resistance (ESR) for the
output capacitor. The minimum output decoupling value is
1.0 mF and can be augmented to fulfill stringent load
transient requirements. The regulator works with ceramic
chip capacitors as well as tantalum devices. Larger values
improve noise rejection and load regulation transient
response. Figure [TBD] shows the stability region for a
range of operating conditions and ESR values.
No−Load Regulation Considerations
The NCP600 adjustable regulator will operate properly
under conditions where the only load current is through the
resistor divider that sets the output voltage. However, in the
case where the NCP600 is configured to provide a 1.250 V
http://onsemi.com
11
NCP600
Noise Decoupling
power dissipation supported by the device is dependent
upon board design and layout. Mounting pad configuration
on the PCB, the board material, and the ambient temperature
affect the rate of junction temperature rise for the part. When
the NCP600 has good thermal conductivity through the
PCB, the junction temperature will be relatively low with
high power applications. The maximum dissipation the
NCP600 can handle is given by:
The NCP600 is a low noise regulator and needs no
external noise reduction capacitor. Unlike other low noise
regulators which require an external capacitor and have slow
startup times, the NCP600 operates without a noise
reduction capacitor, has a typical 15 ms start up delay and
achieves a 50 mVrms overall noise level between 10 Hz and
100 kHz.
Enable Operation
PD(MAX) +
The enable pin will turn the regulator on or off. The
threshold limits are covered in the electrical characteristics
table in this data sheet. The turn−on/turn−off transient
voltage being supplied to the enable pin should exceed a
slew rate of 10 mV/ms to ensure correct operation. If the
enable function is not to be used then the pin should be
connected to Vin.
(eq. 3)
Since TJ is not recommended to exceed 125_C (TJ(MAX)),
then the NCP600 can dissipate up to 400 mW when the
ambient temperature (TA) is 25_C.
The power dissipated by the NCP600 can be calculated
from the following equations:
PD [ VIN([email protected]) ) IOUT(VIN * VOUT)
(eq. 4)
Output Voltage Adjust
or
The output voltage can be adjusted from 1 times
(Figure 2) to 4 times (Figure 3) the typical 1.250 V
regulation voltage via the use of resistors between the output
and the ADJ input. The output voltage and resistors are
chosen using Equation 1 and Equation 2.
ǒ
Ǔ
VOUT + 1.250 1 ) R1 ) (IADJ
R2
R1 + R2 *
TJ(MAX) * TA
RqJA
R2)
VIN(MAX) [
PD(MAX) ) (VOUT IOUT)
IOUT ) IGND
(eq. 5)
If a 150 mA output current is needed, the quiescent current
IGND is taken from the data sheet electrical characteristics
table or extracted from Figure TBD and Figure TBD. IGND
is approximately 108 mA when Iout = 150 mA. For an output
voltage of 1.250 V, the maximum input voltage will then be
3.9 V, good for a 1 Cell Li−ion battery.
(eq. 1)
(IADJ * R2)]
V
ƪ[Vout *1.25
* 1ƫ ^ R2 ƪ out * 1ƫ
1.25
(eq. 2)
Hints
Input bias current IADJ is typically less than 150 nA.
Choose R2 arbitrarily t minimize errors due to the bias
current and to minimize noise contribution to the output
voltage. Use Equation 2 to find the required value for R1.
Vin and GND printed circuit board traces should be as
wide as possible. When the impedance of these traces is
high, there is a chance to pick up noise or cause the regulator
to malfunction. Place external components, especially the
output capacitor, as close as possible to the NCP600, and
make traces as short as possible.
Thermal
As power in the NCP600 increases, it might become
necessary to provide some thermal relief. The maximum
DEVICE ORDERING INFORMATION
Device
Marking Code
Version
NCP600SNADJT1G
LIO
ADJ
NCP600SN150T1G
LID
1.5 V
NCP600SN180T1G
LIE
1.8 V
NCP600SN280T1G
LIH
2.8 V
NCP600SN300T1G
LIJ
3.0 V
NCP600SN330T1G
LIK
3.3 V
NCP600SN500T1G
LIN
5.0 V
Package
Shipping*
TSOP−5
(Pb−Free)
3000/Tape & Reel
*For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting
Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
12
NCP600
PACKAGE DIMENSIONS
TSOP−5
CASE 483−02
ISSUE F
NOTE 5
2X
0.10 T
2X
0.20 T
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. MAXIMUM LEAD THICKNESS INCLUDES
LEAD FINISH THICKNESS. MINIMUM LEAD
THICKNESS IS THE MINIMUM THICKNESS
OF BASE MATERIAL.
4. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
5. OPTIONAL CONSTRUCTION: AN
ADDITIONAL TRIMMED LEAD IS ALLOWED
IN THIS LOCATION. TRIMMED LEAD NOT TO
EXTEND MORE THAN 0.2 FROM BODY.
D 5X
0.20 C A B
5
1
4
2
3
M
B
S
K
L
DETAIL Z
G
A
DIM
A
B
C
D
G
H
J
K
L
M
S
DETAIL Z
J
C
0.05
SEATING
PLANE
H
T
SOLDERING FOOTPRINT*
0.95
0.037
MILLIMETERS
MIN
MAX
3.00 BSC
1.50 BSC
0.90
1.10
0.25
0.50
0.95 BSC
0.01
0.10
0.10
0.26
0.20
0.60
1.25
1.55
0_
10 _
2.50
3.00
1.9
0.074
2.4
0.094
1.0
0.039
0.7
0.028
SCALE 10:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
13
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP600/D