STMicroelectronics LK112SM16TR Low noise low drop voltage regulator with shutdown function Datasheet

LK112S
SERIES
LOW NOISE LOW DROP VOLTAGE REGULATOR
WITH SHUTDOWN FUNCTION
■
■
■
■
■
■
■
OUTPUT CURRENT UP TO 200mA
LOW DROPOUT VOLTAGE (500mV MAX AT
IOUT=200mA)
VERY LOW QUIESCENT CURRENT: 0.1µA
IN OFF MODE AND MAX 250µA IN ON
MODE AT IOUT=0mA
LOW OUTPUT NOISE: TYP 30µV AT
IOUT=60mA AND 10Hz<f<80KHz
WIDE RANGE OF OUTPUT VOLTAGES
INTERNAL CURRENT AND THERMAL LIMIT
VOUT TOLERANCE ± 2% (AT 25°C)
DESCRIPTION
The LK112S is a low dropout linear regulator with
a built in electronic switch. The internal switch can
be controlled by TTL or CMOS logic levels. The
device is ON state when the control pin is pulled to
a logic high level. An external capacitor can be
used connected to the noise bypass pin to lower
the output noise level to 30µVrms. An internal PNP
pass transistor is used to achieve a low dropout
voltage.
SOT23-5L
The LK112S has a very low quiescent current in
ON MODE while in OFF MODE the Iq is reduced
down to 100nA max. The internal thermal
shutdown circuitry limits the juntion temperature to
below 150°C. The load current is internally
monitored and the device will shutdown in the
presence of a short circuit or overcurrent condition
at the output.
SCHEMATIC DIAGRAM
February 2003
1/11
LK112S SERIES
ABSOLUTE MAXIMUM RATINGS
Symbol
VI
VSHDN
IO
Parameter²
Value
Unit
DC Input Voltage
16
V
Shutdown Input Voltage
16
V
Output Current
Internally limited
Tstg
Storage Temperature Range
-55 to +150
°C
Top
Operating Junction Temperature Range
-30 to +80
°C
CONNECTION DIAGRAM (top view)
PIN DESCRIPTION
Pin N° Symbol
1
SHDN
Shutdown Input: Disables the
regulator when is connected to GND
or to positive voltage less than 0.6V
GND Ground Pin: Internally connected to
the die attach flag to decrease the
total thermal resistance and increase
the package ability to dissipate
power.
Bypass Bypass Pin: Bypass with 0.1µF to
improve the Vref thermal noise
performances.
OUT Output Port
IN
Input Port
2
3
SOT23-5L
Name and Function
4
5
ELECTRICAL CHARACTERISTICS FOR LK112 (Tj = 25°C, VIN=VOUT+1V (see Note 1), IOUT=0mA,
VSHDN=1.8V, CI = 1 µF, CO = 2.2µF, CBYPASS = 0.1µF unless otherwise specified)
Symbol
Id
Parameter
Test Conditions
Quiescent Current
ON MODE (except ISHDN)
VSHDN = 0V
OFF MODE VI = 8V
VO
Output Voltage
IO = 30mA
∆VO
Line Regulation
∆VO
Vd
ISC
Load Regulation
Dropout Voltage
Min.
Typ.
Max.
Unit
175
250
µA
0
0.1
µA
(see table)
VI = VO+1V to VO+6V,
VO ≤ 5.6V
0.7
20
mV
VI = VO+1V to VO+6V,
VO > 5.6V
0.8
40
mV
IO = 1 to 60mA
15
30
mV
IO = 1 to 200mA
30
90
mV
IO = 60 mA (see Note 2)
0.17
0.24
V
IO = 200 mA (see Note 2)
0.35
0.5
V
Short Circuit Current
200
mA
Supply Voltage Rejection
CBYP = 0.1µF
VI = VO+1.5V
CO = 10µF f = 400Hz
IO = 30mA
55
dB
Output Noise Voltage
B= 10Hz to 80KHz CBYP = 0.1µF
CO = 10µF VI = VO+1.5V,IO = 60mA
30
µVrms
ISHDN
Shutdown Input Current
VSHDN = 1.8V
12
VSHDN
Shutdown Input Logic
Output ON
Output OFF
IO = 10mA
SVR
eN
∆VO/Tj
Output Voltage
Temperature Coefficient
Note 1: for version with output voltage less than 2V VIN=2.4V
Note 2: only for version with output voltage more than 2.1V
2/11
Output ON
35
µA
0.6
V
V
mV/°C
1.8
0.09
LK112S SERIES
ORDERING NUMBERS AND OUTPUT VOLTAGE
Part Number
LK112SM13TR
LK112SM14TR (*)
LK112SM15TR
LK112SM16TR
LK112SM17TR (*)
LK112SM18TR
LK112SM19TR (*)
LK112SM20TR (*)
LK112SM21TR
LK112SM22TR (*)
LK112SM23TR (*)
LK112SM24TR (*)
LK112SM25TR
LK112SM26TR (*)
LK112SM27TR (*)
LK112SM28TR
LK112SM29TR (*)
LK112SM30TR
LK112SM31TR (*)
LK112SM32TR
LK112SM33TR
LK112SM34TR (*)
LK112SM35TR (*)
LK112SM36TR
LK112SM37TR (*)
LK112SM38TR
LK112SM39TR (*)
LK112SM40TR
LK112SM41TR (*)
LK112SM42TR (*)
LK112SM43TR (*)
LK112SM44TR (*)
LK112SM45TR (*)
LK112SM46TR (*)
LK112SM47TR
LK112SM48TR (*)
LK112SM49TR (*)
LK112SM50TR
LK112SM55TR (*)
LK112M60TR
LK112SM80TR
Output Voltage
VOUT Min
VOUT Max
Test Voltage
1.3V
1.4V
1.5V
1.6V
1.7V
1.8V
1.9V
2.0V
2.1V
2.2V
2.3V
2.4V
2.5V
2.6V
2.7V
2.8V
2.9V
3.0V
3.1V
3.2V
3.3V
3.4V
3.5V
3.6V
3.7V
3.8V
3.9V
4.0V
4.1V
4.2V
4.3V
4.4V
4.5V
4.6V
4.7V
4.8V
4.9V
5.0V
5.5V
6.0V
8.0V
1.24V
1.34V
1.44V
1.54V
1.64V
1.74V
1.84V
1.94V
2.04V
2.14V
2.24V
2.34V
2.44V
2.54V
2.64V
2.74V
2.84V
2.94V
3.04V
3.14V
3.24V
3.335V
3.435V
3.535V
3.630V
3.725V
3.825V
3.920V
4.020V
4.120V
4.215V
4.315V
4.410V
4.510V
4.605V
4.705V
4.800V
4.900V
5.390V
5.880V
7.840V
1.36V
1.46V
1.56V
1.66V
1.76V
1.86V
1.96V
2.06V
2.16V
2.26V
2.36V
2.46V
2.56V
2.66V
2.76V
2.86V
2.96V
3.06V
3.16V
3.26V
3.36V
3.465V
3.565V
3.655V
3.770V
3.875V
3.975V
4.080V
4.180V
4.280V
4.385V
4.485V
4.590V
4.690V
4.795V
4.895V
5.000V
5.100V
5.610V
6.120V
8.160V
2.4V
2.4V
2.4V
2.4V
2.4V
2.4V
2.4V
3.0V
3.1V
3.2V
3.3V
3.4V
3.5V
3.6V
3.7V
3.8V
3.9V
4.0V
4.1V
4.2V
4.3V
4.4V
4.5V
4.6V
4.7V
4.8V
4.9V
5.0V
5.1V
5.2V
5.3V
5.4V
5.5V
5.6V
5.7V
5.8V
5.9V
6.0V
6.5V
7.0V
9.0V
(*) Available on request
3/11
LK112S SERIES
TYPICAL CHARACTERISTICS (unless otherwise specified Tj = 25°C, CI=1µF, CO=2.2µF, CBYP=100nF)
Figure 1 : Output Voltage vs Temperature
Figure 4 : Load Regulation vs Temperature
Figure 2 : Output Voltage vs Temperature
Figure 5 : Dropout Voltage vs Temperature
Figure 3 : Line Regulation vs Temperature
Figure 6 : Short Circuit Currennt vs Dropout
Voltage
4/11
LK112S SERIES
Figure 7 : Output Voltage vs Input Voltage
Figure 10 : Supply Voltage Rejection vs
Temperature
Figure 8 : Shutdown Voltage vs Temperature
Figure 11 : Supply Voltage Rejection vs Output
Current
Figure 9 : Shutdown Current vs Shutdown
Voltage
Figure 12 : Supply Voltage Rejection vs
Frequency
5/11
LK112S SERIES
Figure 13 : Supply Voltage Rejection vs
Temperature
Figure 16 : Quiescent Current vs Shutdown
Voltage
Figure 14 : Quiescent Current vs Temperature
Figure 17 : Quiescent Current vs Output Current
Figure 15 : Quiescent Current vs Input Voltage
Figure 18 : Reverse Current vs Reverse Voltage
6/11
LK112S SERIES
Figure 19 : Stability
Figure 22 : Start-up Transient
VI=3.5V, V O=2.5V, VSHDN = 0 to 1.8V, RL=68Ω, CI=1µF, CO=4.7µF,
CBY=100nF
Figure 20 : Spectrum Noise
Figure 23 : Line Transient
VI=3.5 to 4.5V, V O=2.5V, V SHDN=1.8V, I O=30mA, No CI, CO=10µF,
CBY=100nF, ts=tf=2µs
Figure 21 : Start-up Transient
Figure 24 : Line Transient
VI=3.5V, V O=2.5V, V SHDN= 0 to 1.8V, RL=2.5KΩ, CI=1µF,
CO=4.7µF, CBY=10nF
VI=3.5 to 4.5V, V O=2.5V, V SHDN=1.8V, I O=30mA, No CI, CO=10µF,
CBY=10nF, t s=tf=2µs
7/11
LK112S SERIES
Figure 25 : Line Transient
Figure 27 : Load Transient
VI=3.5 to 4.5V, V O=2.5V, VSHDN =1.8V, IO=30mA, No CI, CO=1µF,
CBY=1nF, t s=tf=2µs
VI=3.5V, V O=2.5V, V SHDN=1.8V, IO=50 to 100mA, CI1µF,
CO=10µF, CBY =100nF, ts=tf=250ns
Figure 26 : Load Transient
Figure 28 : Load Transient
VI=3.5 V, V O=2.5V, VSHDN=1.8V, IO=50 to 100mA, C I=1µF,
CO=2.2µF, CBY=10nF, t s=tf=250ns
VI=4.8 V, V O=3.8V, VSHDN=1.8V, IO=50 to 100mA, C I=1µF,
CO=2.2µF, CBY=10nF, t s=tf=250ns
8/11
LK112S SERIES
SOT23-5L MECHANICAL DATA
mm.
mils
DIM.
MIN.
TYP
MAX.
MIN.
TYP.
MAX.
A
0.90
1.45
35.4
57.1
A1
0.00
0.15
0.0
5.9
A2
0.90
1.30
35.4
51.2
b
0.35
0.50
13.7
19.7
C
0.09
0.20
3.5
7.8
D
2.80
3.00
110.2
118.1
E
2.60
3.00
102.3
118.1
E1
1.50
1.75
59.0
68.8
e
0 .95
37.4
e1
1.9
74.8
L
0.35
0.55
13.7
21.6
9/11
LK112S SERIES
Tape & Reel SOT23-xL MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
A
MIN.
TYP.
180
13.0
13.2
MAX.
7.086
C
12.8
D
20.2
0.795
N
60
2.362
T
10/11
MAX.
0.504
0.512
14.4
0.519
0.567
Ao
3.13
3.23
3.33
0.123
0.127
0.131
Bo
3.07
3.17
3.27
0.120
0.124
0.128
Ko
1.27
1.37
1.47
0.050
0.054
0.0.58
Po
3.9
4.0
4.1
0.153
0.157
0.161
P
3.9
4.0
4.1
0.153
0.157
0.161
LK112S SERIES
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from
its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications
mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information
previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or
systems without express written approval of STMicroelectronics.
© The ST logo is a registered trademark of STMicroelectronics
© 2003 STMicroelectronics - Printed in Italy - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco
Singapore - Spain - Sweden - Switzerland - United Kingdom - United States.
© http://www.st.com
11/11
Similar pages