AME AME8819AEGT330Z Low dropout 600ma cmos regulator Datasheet

AME
Low Dropout
600mA CMOS Regulator
AME8819
n General Description
The AME8819 is a CMOS linear regulator. It operated from
2.5V to 5.5V input voltage and delivers up to 600mA output
current. The AME8819 provide low quiescent current (70uA
typ) low dropout voltage (Vout=3.3V, 540mV @ 600mA typ),
and excellent PSRR, thus marking them ideal for Data-Communications and battery applications.
n Functional Block Diagram
(Fixed Version)
IN
OUT
Overcurrent
Shutdown
Thermal
Shutdown
The AME8819 provide over temperature and over current
protected functions. It is stable with an output capacitance of
2.2uF or larger.
R1
Bandgap
Reference
R2
GND
n Features
l Input voltage range is from 2.8V to 5.5V
l Output voltage range is from 1.8V to 4.5V
(Adjustable Version)
IN
OUT
l Low Dropout: 540mV @ 600mA, VOUT = 3.3V
Overcurrent
Shutdown
l Guaranteed 600mA Drive Current
l Factory Pre-set output voltage
Thermal
Shutdown
l Only 2.2µF Output Capacitor Required for
Stability (Low ESR MLCC is allowable)
R1
(external)
EN
l Provided OTP, current limit
l All AME’ s Green Products Meet RoHS
Standards
Bandgap
Reference
ADJ
R2
(external)
GND
n Applications
l Data-Communication
l Laptop, Palmtops, Notebook computers
l Battery Power Equipment
l Handheld Device
l PCMCIA Cards
Rev.B.01
1
AME
Low Dropout
600mA CMOS Regulator
AME8819
n Typical Application
(Fixed Version)
(Adjustable Version)
VIN
VOUT
IN
OUT
AME8819
VIN
AME8819
EN
GND
CIN
1µF
2
COUT
2.2µF
C1
1µF
V OUT
OUT
IN
GND
ADJ
R1
VREF
C2
2.2µF
R2
Rev.B.01
AME
Low Dropout
600mA CMOS Regulator
AME8819
n Pin Configuration
SOT-89
Top View
SOT-89
Top View
AME8819AEFT
AME8819BEFT
1. IN
AME8819
2. GND (TAB)
AME8819
3. OUT
1
2
3
1
2
3
Die Attach:
Die Attach:
Conductive Epoxy
Non-Conductive Epoxy
SOT-223
Top View
AME8819
AME8819AEGT
AME8819BEGT
1. IN
1. GND
2. GND (TAB)
AME8819
3. OUT
2
2. IN (TAB)
3. OUT
SOT-223
Top View
1
1. GND
3. IN
1
3
2. OUT (TAB)
2
3
Die Attach:
Die Attach:
Conductive Epoxy
Non-Conductive Epoxy
SOP-8
Top View
8
7
6
5
AME8819AEHAADJ
1. EN
2. IN
3. OUT
AME8819
4. ADJ
5. GND
6. GND
7. GND
1
2
3
4
8. GND
Die Attach:
Conductive Epoxy
Rev.B.01
3
AME
Low Dropout
600mA CMOS Regulator
AME8819
n Pin Description
Pin Name
IN
4
Pin Description
Input voltage pin.
It should be decoupled with 1µF or greater capacitor.
GND
Ground connection pin.
OUT
LDO voltage regulator output pin.
It should be decoupled with a 2.2µF or greater value low ESR ceramic capacitor.
EN
Enable pin.
When pulled low, the PMOS pass transistor turns off, current consuming less than 10µA.
ADJ
Feedback output voltage for adjustable device.
Rev.B.01
AME
Low Dropout
600mA CMOS Regulator
AME8819
n Ordering Information
AME8819 x x x x xxx x
Special Feature1
Output Voltage
Number of Pins
Package Type
Operating Ambient Temperature Range
Pin Configuration
Pin
Configuration
Operating Ambient
Temperature Range
A: 1. IN
2. GND
(SOT-223) 3. OUT
E: -40OC to +85OC
(SOT-89)
B: 1.GND
2.IN
3.OUT
(SOT-89)
B: 1.GND
2.OUT
3.IN
(SOT-223)
Package
Type
F: SOT-89
G: SOT-223
H: SOP
Number of
Output Voltage
Pins
T: 3
A: 8
180:
250:
280:
285:
290:
300:
310:
330:
360:
ADJ:
Special
Feature 1
V=1.8V
Z: Green
V=2.5V
V=2.8V
V=2.85V
V=2.9V
V=3.0V
V=3.1V
V=3.3V
V=3.6V
Adjustable
A: 1.EN
2.IN
3.OUT
4.ADJ
5.GND
6.GND
7.GND
8.GND
(SOP-8)
Rev.B.01
5
AME
Low Dropout
600mA CMOS Regulator
AME8819
n Available Options
Part Number
Marking
Output
Voltage
Package
Operating Ambient
Temperature Range
AME8819AEFT180Z
A8819
CIyMXX
1.8V
SOT-89
-40OC to +85OC
AME8819AEFT250Z
A8819
CGyMXX
2.5V
SOT-89
-40OC to +85OC
AME8819AEFT300Z
A8819
CDyMXX
3.0V
SOT-89
-40OC to +85OC
AME8819AEFT330Z
A8819
CByMXX
3.3V
SOT-89
-40OC to +85OC
AME8819BEFT180Z
A8819
DIyMXX
1.8V
SOT-89
-40OC to +85OC
AME8819BEFT250Z
A8819
DGyMXX
2.5V
SOT-89
-40OC to +85OC
AME8819BEFT300Z
A8819
DDyMXX
3.0V
SOT-89
-40OC to +85OC
AME8819BEFT330Z
A8819
DByMXX
3.3V
SOT-89
-40OC to +85OC
AME8819AEGT180Z
A8819
AIyMXX
1.8V
SOT-223
-40OC to +85OC
AME8819AEGT250Z
A8819
AGyMXX
2.5V
SOT-223
-40OC to +85OC
AME8819AEGT300Z
A8819
ADyMXX
3.0V
SOT-223
-40OC to +85OC
AME8819AEGT330Z
A8819
AByMXX
3.3V
SOT-223
-40OC to +85OC
AME8819BEGT180Z
A8819
BIyMXX
1.8V
SOT-223
-40OC to +85OC
AME8819BEGT250Z
A8819
BGyMXX
2.5V
SOT-223
-40OC to +85OC
AME8819BEGT300Z
A8819
BDyMXX
3.0V
SOT-223
-40OC to +85OC
Note:
1. The first 2 places represent product code. It is assigned by AME such as CI.
2. y is year code and is the last number of a year. Such as the year code of 2008 is 8.
3. A bar on top of first letter represents Green Part such as A8819.
4. The last 3 places MXX represent Marking Code. It contains M as date code in "month", XX as LN code and
that is for AME internal use only. Please refer to date code rule section for detail information.
5. Please consult AME sales office or authorized Rep./Distributor for the availability of output voltage and package
type.
6
Rev.B.01
AME
Low Dropout
600mA CMOS Regulator
AME8819
n Available Options
Part Number
Marking
Output
Voltage
Package
Operating Ambient
Temperature Range
AME8819BEGT330Z
A8819
BByMXX
3.3V
SOT-223
-40OC to +85OC
Rev.B.01
7
AME
Low Dropout
600mA CMOS Regulator
AME8819
n Absolute Maximum Ratings
Parameter
Symbol
Maximum
Unit
Input Voltage
VIN
-0.3 to 6
V
EN Voltage
VEN
-0.3 to 6
V
Output Current
IOUT
PD / (V IN -V OUT)
mA
Output Voltage
VOUT
GND-0.3 to VIN +0.3
V
B*
ESD Classification
Caution: Stress above the listed absolute maximum rating may cause permanent damage to the device.
* HBM B:2000V~3999V
n Recommended Operating Conditions
Parameter
8
Symbol
Rating
Ambient Temperature Range
TA
-40 to +85
Junction Temperature Range
TJ
-40 to +125
Storage Temperature Range
TSTG
-65 to +150
Unit
o
C
Rev.B.01
AME
Low Dropout
600mA CMOS Regulator
AME8819
n Thermal Information
Parameter
Package
SOT-89*
Thermal Resistance
(Junction to Case)
SOT-223*
SOT-89
SOP-8
SOT-89
Internal Power Dissipation
Non-Conductive
Epoxy
46
SOP-8
θJC
25
Non-Conductive
Epoxy
31
Conductive Epoxy
60
Conductive Epoxy
180
Non-Conductive
Epoxy
180
θJA
120
Non-Conductive
Epoxy
135
Conductive Epoxy
150
Conductive Epoxy
550
Non-Conductive
Epoxy
550
Conductive Epoxy
SOT-223
Maximum
40
Conductive Epoxy
SOT-223
Symbol
Conductive Epoxy
Conductive Epoxy
SOP-8**
Thermal Resistance
(Junction to Ambient)
Die Attach
PD
900
Non-Conductive
Epoxy
800
Conductive Epoxy
810
Unit
o
C/W
o
C/W
mW
Maximum Junction Temperature
150
o
C
Solder Iron(10 Sec)***
350
o
C
* Measure θJC on backside center of tab.
** Measure θJC on center of molding compound if IC has no tab.
*** MIL-STD-202G 210F
Rev.B.01
9
AME
Low Dropout
600mA CMOS Regulator
AME8819
n Electrical Specifications
VIN = VOUT(NOM) + 1V, IOUT = 1mA, CIN=1µF, COUT = 4.7µF, Typical values at TA = 25oC, unless otherwise noted.
Parameter
Symbol
Test Conditions
Min
Typ Max Units
(Note1)
5.5
Input Voltage
V IN
ADJ Input Bias Current
IADJ
ADJ Reference Voltage
VREF
0.970
V OUT,ACC
-2
2
%
Output Voltage Range
VOUT
1.8
4.5
V
Output Current
IOUT
600
Output Voltage Accuracy
Quiescent Current
Dropout Voltage
Output Voltage Line
Regulation
[(∆V OUT / ∆V IN )x100%] /
IQ
VDROP
REG LINE
V IN =5V, VADJ =0.980
µA
1
V IN = 5.5V, IOUT = 1mA
IOUT = 600mA
V
0.980 0.990
V
mA
µA
70
100
1.8V≦ V OUT≦ 2.5V
800
1000
2.5V<V OUT≦3.3V
540
800
3.3V<V OUT≦4.5V
470
650
V IN(min)≦V IN ≦V IN(max)
1.8V≦ V OUT<2.5V
-0.4
0.1
0.4
V IN(min)≦V IN ≦V IN(max)
2.5≦V OUT<3.3V
-0.2
0.03
0.2
-0.1
0.01
0.1
mV
%/V
V OUT
V OUT+0.3V≦V IN≦V IN(max) 3.3V≦ V OUT <4.5V
1.8V≦ V OUT<2.5V,
Output Voltage Load
Regulation
[(∆V OUT / V OUT) x 100%]
V IN =V in(min)
REG LOAD
/∆IOUT
1mA≦ IOUT≦600mA
2.5V≦ V OUT<3.3V,
V IN =V in(min)
3.3V≦ V OUT≦ 4.5V,
V IN =V in(min)
Output Current Limit
10
-0.015
0.01
-0.005
0.004 %/mA
-0.003
0.002
ILIM
V OUT = 0.8 x VOUT(NOM)
650
800
Shutdown Current
ISHDN
VEN = 0V, VIN(min) ≦ V IN ≦ 5.5V
5
Power Supply Ripple
Rejection
PSRR
f = 1KHz, IOUT = 100mA, Cout=1µF
60
mA
10
µA
dB
Rev.B.01
AME
Low Dropout
600mA CMOS Regulator
AME8819
n Electrical Specifications
Symbol
Test Conditions
Enable High (enabled)
VEN(HI)
VIN(min) ≦ VIN ≦ 5.5V
1.4
VIN
V
Enable Low (shutdown)
VEN(LO)
VIN(min) ≦ VIN ≦ 5.5V
0
0.4
V
IEN
VEN = V IN
0.1
1
µA
TSHDN
Shutdown, temperature increasing
150
TRS
Restore, temperature decreasing
130
Parameter
Enable Pin Current
(enabled)
Thermal Shutdown
Temperature
Min Typ Max Units
O
C
Note 1: VIN(MIN)=VOUT+VDROP .
Rev.B.01
11
AME
AME8819
n Detailed Description
The AME8819 is low-dropout, low quiescent-current linear
regulator designed primarily for battery-powered applications.
It is available with present output voltage ranging from 1.8V
to 3.6V, and can supply loads up to 600mA.
n Circuit Limit
The AME8819 contains current limiters which monitor and
control the pass transistor's Gate voltage, limiting the guaranteed maximum output current to 650mA minimum. The
output can be shorted to ground for an indefinite time without
damaging the part.
n Thermal-Overload Protection
Thermal-overload protection limits total power dissipation
in the AME8819. When the junction temperature arrive TJ =
160oC approximately, the thermal sensor signals the shutdown logic, turning off the pass transistor and allowing the IC
to cool.
Low Dropout
600mA CMOS Regulator
n Capacitor Selection and
Regulator Stability
Use 1µF capacitor on the OUT. Larger input capacitor values and lower ESR provide better supply noise
rejection and line transient response. To reduce output noise and improve load transient voltage dips, use
larger output capacitors up to 4.7µF. For stable operation over the full temperature range with load currents up to 600mA, input and output capacitors should
be a minimum of 2.2µF by X7R.
Note that some ceramic dielectrics large capacitance
and ESR variation with temperature. With dielectrics
such as Z5U and Y5V, it may be necessary to use
4.7µF or more for up to 600mA load current to ensure
stability at temperatures below -10oC. With X7R or
X5R dielectrics, 2.2µF is sufficient at all operating temperatures. These regulators are optimized for ceramic
capacitors. Tantalum capacitors are not recommended.
n PSRR and Operation from
sources Other than Batteries
The AME8819 is designed to deliver low-dropout
voltage and low quiescent currents in battery-powered
system. Power-supply rejection ratio is 60dB(Typ.)
at 1KHz (see PSRR vs Frequency Curve).When operating from sources other than batteries, PSRR and
transient response can be improved by increasing input, output capacitors.
12
Rev.B.01
AME
Low Dropout
600mA CMOS Regulator
AME8819
Output Voltage vs Temperature
Quiesent Current vs Temprature
100
3.06
VOUT = 3.0V
IOUT=1mA
3.02
Quiesent Current (V)
Output Voltage (V)
3.04
3.00
2.98
IOUT=600mA
2.96
2.94
80
60
IOUT =600mA
IOUT=1mA
40
20
2.92
V OUT = 3.0V
2.90
-50
-25
0
+25
+50
+75
+100
0
-50
+125
0
+25
+50
+75
+100
Temperature (oC)
Current Limit vs Input Voltage
Dropout Voltage vs Load Current
1020
+125
800
VOUT = 3.0V
1015
Dropout Voltage (mV)
700
Current Limit (mA)
-25
Temperature ( C)
o
1010
1005
1000
995
990
985
980
VOUT = 3.0V
IOUT = 600mA
TA=125O C
600
500
400
300
TA=25OC
200
TA=-40OC
100
975
970
4
4.5
5
0
0
5.5
Input Voltage (V)
100
200
300
400
500
600
Load Current (mA)
Power Supply Rejection Ratio
Line Transient Response
VIN = 4.0V
VOUT = 3.0V
90
80
60
IOUT =100mA
50
40
IOUT =10mA
30
20
10
V OUT (10mV/DIV)
PSRR (dB)
70
VIN(1V/DIV)
100
VIN = 4V~5V
VOUT = 3.0V
IOUT = 1mA
0
1K
10K
100K
Frequency (Hz)
Rev.B.01
1M
TIME (100µSec/DIV)
13
AME
Low Dropout
600mA CMOS Regulator
AME8819
V OUT = 3.0V
IOUT = 1mA~550mA
I OUT (200mA/DIV)
V OUT (50mV/DIV)
Load Transient Response
TIME (100µSec/DIV)
14
Rev.B.01
AME
Low Dropout
600mA CMOS Regulator
AME8819
n Date Code Rule
Month Code
1: January 7: July
2: February 8: August
3: March
9: September
4: April
A: October
5: May
B: November
6: June
C: December
n Tape and Reel Dimension
SOT-89
P
W
AME
AME
PIN 1
Carrier Tape, Number of Components Per Reel and Reel Size
Rev.B.01
Package
Carrier Width (W)
Pitch (P)
Part Per Full Reel
Reel Size
SOT-89
12.0±0.1 mm
4.0±0.1 mm
1000pcs
180±1 mm
15
AME
Low Dropout
600mA CMOS Regulator
AME8819
n Tape and Reel Dimension
SOT-223
P
W
AME
AME
PIN 1
Carrier Tape, Number of Components Per Reel and Reel Size
Package
Carrier Width (W)
Pitch (P)
Part Per Full Reel
Reel Size
SOT-223
12.0±0.1 mm
4.0±0.1 mm
2500pcs
330±1 mm
SOP-8
P
PIN 1
W
AME
AME
AME
AME
Carrier Tape, Number of Components Per Reel and Reel Size
16
Package
Carrier Width (W)
Pitch (P)
Part Per Full Reel
Reel Size
SOP-8
12.0±0.1 mm
4.0±0.1 mm
2500pcs
330±1 mm
Rev.B.01
AME
Low Dropout
600mA CMOS Regulator
AME8819
n Package Dimension
SOT-89
BOTTOM VIEW
D
D1
D2
H
SIDE VIEW
E2
E
3'
10'
A1
PIN 1
C
e
S1
TOP VIEW
SYMBOLS
A
I
FRONT VIEW
Rev.B.01
MILLIMETERS
INCHES
MIN
MAX
MIN
MAX
A
1.39
1.60
0.05472
0.06299
A1
0.89
1.20
0.03503
0.04724
C
0.35
0.44
0.01378
0.01732
D
4.39
4.60
0.17283
0.18110
D1
1.35
1.83
0.05315
0.07205
E
2.28
2.60
0.08976
0.10236
I
0.36
0.56
0.01256
0.02204
e
3.00 REF
0.11811 REF
H
0.70 REF
0.02756 REF
S1
1.50 REF
0.05906 REF
E2
2.05
2.60
0.08071
0.10236
D2
1.50
1.85
0.05905
0.07283
17
AME
Low Dropout
600mA CMOS Regulator
AME8819
n Package Dimension
SOT-223
Top View
Side View
SYMBOLS
D
B1
θ
C
o
13 (4X)
H
PIN 1
E
e
INCHES
MIN
MAX
MIN
MAX
A1
0.01
0.10
0.0004
0.0039
B
0.60
0.84
0.0236
0.0330
B1
2.90
3.15
0.1140
0.1240
C
0.24
0.38
0.0094
0.0150
D
6.20
6.71
0.2441
0.2640
E
3.30
3.71
0.1299
0.1460
2.30 BSC
e
Front View
18
MILLIMETERS
0.0906 BSC
o
13 (4X)
F
1.40
1.80
0.0551
0.0709
F
H
6.70
7.30
0.2638
0.2874
A1
θ
B
0
o
10
o
0
o
10
o
Rev.B.01
AME
Low Dropout
600mA CMOS Regulator
AME8819
n Package Dimension
SOP-8
Top View
C
E
H
L
D
θ
PIN 1
Side View
Front View
o
e
A1
A
A2
7 ( 4 X)
SYMBOLS
MAX
MIN
MAX
A
1.35
1.75
0.0531
0.0689
A1
0.10
0.30
0.0039
0.0118
1.473 REF
0.05799 REF
B
0.33
0.51
0.0130
0.0201
C
0.17
0.25
0.0067
0.0098
D
4.70
5.33
0.1850
0.2098
E
3.80
4.00
0.1496
0.1575
1.27 BSC
e
0.05000 BSC
L
0.40
1.27
0.0157
0.0500
H
5.80
6.30
0.2283
0.2480
y
-
0.10
-
0.0039
θ
Rev.B.01
INCHES
MIN
A2
B
MILLIMETERS
0
o
8
o
0
o
8
o
19
www.ame.com.tw
E-Mail: [email protected]
Life Support Policy:
These products of AME, Inc. are not authorized for use as critical components in life-support
devices or systems, without the express written approval of the president
of AME, Inc.
AME, Inc. reserves the right to make changes in the circuitry and specifications of its devices and
advises its customers to obtain the latest version of relevant information.
 AME, Inc. , May 2009
Document: 1261-DS8819-B.01
Corporate Headquarter
AME, Inc.
2F, 302 Rui-Guang Road, Nei-Hu District
Taipei 114, Taiwan, R.O.C.
Tel: 886 2 2627-8687
Fax: 886 2 2659-2989
Similar pages