Holt HI-8592PSM Single-rail arinc 429 differential line driver Datasheet

HI-8592, HI-8593, HI-8594
October, 2010
Single-Rail ARINC 429 Differential Line Driver
GENERAL DESCRIPTION
PIN CONFIGURATION (TOP VIEW)
The HI-8592 bus interface product is a silicon gate
CMOS device designed as a line driver in accordance
with the ARINC 429 bus specifications. The part includes a negative voltage converter allowing it to operate from a single +5V supply using only two external capacitors. The part also features high-impedance outputs
(tri-state) when both data inputs are taken high, allowing
multiple line drivers to be connected to a common bus.
14 AMPB
V+ 1
13 TXBOUT
SLP 2
TX0IN 3
12 AMPA
TX1IN 4
11 TXAOUT
10 V-
GND 5
The HI-8593 and HI-8594 are reduced pin count versions of HI-8592 which do not incorporate the negative
voltage converter. These devices are compatible with
Holt’s existing HI-8570 and HI-8571 respectively, with
the added advantage of the tri-state outputs. For even
smaller board footprint, versions are also available in
leadless, surface mount QFN-style packages.
CAP+ 6
9 GND
CAP- 7
8 V+
HI-8592PS
14-PIN PLASTIC SMALL OUTLINE (ESOIC) NB
SLP 1
Logic inputs feature built-in 2,000V minimum ESD input
protection as well as 5V or 3.3V logic level compatibility.
8 V+
TX0IN 2
7 TXBOUT
TX1IN 3
6 TXAOUT
GND 4
5 V-
HI-8593PS
8-PIN PLASTIC SMALL OUTLINE (ESOIC) NB
Products with 5 Ohm or 37.5 Ohm resistors in series
with each ARINC output are available to allow the use of
external resistors for lightning protection.
SLP 1
The HI-859x series of line drivers are intended for use
where logic signals must be converted to ARINC 429
levels such as when using an FPGA or the HI-3584
ARINC 429 Serial Transmitter/Dual Receiver.
8 V+
TX0IN 2
7 AMPB
TX1IN 3
6 AMPA
GND 4
5 V-
HI-8594PS
8-PIN PLASTIC SMALL OUTLINE (ESOIC) NB
o
The family of parts are available in Industrial -40 C to
o
o
o
+85 C, or Extended, -55 C to +125 C temperature ranges. Optional burn-in is available on the extended temperature range.
(See page 9 for additional package pin configurations)
FEATURES
Table 1. Function Table
• Single +5V supply
• Negative voltage generated on-chip (HI-8592)
• Digitally selectable rise and fall times
TX1IN
TX0IN
SLP
TXAOUT
TXBOUT
SLOPE
0
0
X
0V
0V
N/A
0
1
0
-5V
5V
10μs
• Tri-state Outputs
0
1
1
-5V
5V
1.5μs
• Plastic 8 & 14-pin thermally enhanced SOIC
packages available
1
0
0
5V
-5V
10μs
1
0
1
5V
-5V
1.5μs
• 5 Ohm or 37.5 Ohm output resistance
1
1
X
Hi-Z
Hi-Z
N/A
• Industrial and Extended temperature ranges
• Burn-in available
DS8592 Rev. B
HOLT INTEGRATED CIRCUITS
www.holtic.com
1
10/10
HI-8592, HI-8593, HI-8594
BLOCK DIAGRAM
V+
CSUPPLY
5V
AMPA
SLP
TX0IN
5V
ONE
ESD
PROTECTION
& VOLTAGE
TRANSLATION
CURRENT
CONTROL
NULL
“A” SIDE
TXAOUT
5Ω
32.5Ω
ZERO
TX1IN
CONTROL
LOGIC
-5V
AMPB
5V
ONE
CURRENT
CONTROL
NULL
GND
“B” SIDE
5Ω
ZERO
CONTROL
LOGIC
TXBOUT
32.5Ω
-5V
V+
CAP+
CFLY
CAP-
-5V
Switched Capacitor
DC-DC Inverter
VCOUT
Clock Generation
Figure 1. HI-8592 Block Diagram
HOLT INTEGRATED CIRCUITS
2
HI-8592, HI-8593, HI-8594
PIN DESCRIPTIONS
Table 2. Pin Descriptions
Pin
Function
Description
V+
POWER
+5V power supply
SLP
INPUT
Output slew rate control. High selects ARINC 429 high-speed. Low selects
ARINC 429 low-speed.
TX0IN
INPUT
Data input zero
TX1IN
INPUT
Data input one
GND
POWER
Ground supply
CAP+
ANALOG
Positive connection for external capacitor, CFLY
CAP-
ANALOG
Negative connection for external capacitor, CFLY
V-
POWER
-5V supply, may be connected to supply or used with on-chip negative supply converter
TXAOUT
OUTPUT
ARINC high output with 37.5 Ohms series resistance
AMPA
OUTPUT
ARINC high output with 5 Ohms series resistance
TXBOUT
OUTPUT
ARINC low output with 37.5 Ohms series resistance
AMPB
OUTPUT
ARINC low output with 5 Ohms series resistance
V+ = 5V
CSUPPLY = 68µF
HI-3584A
SLP
TX0IN
TXAOUT
TX1IN
TXBOUT
AMPA
ARINC 429
Bus
AMPB
HI-8592
CAP+
CFLY = 4.7µF
CAP- GND
-5V
COUT = 47µF
Figure 2. Application Example
HOLT INTEGRATED CIRCUITS
3
HI-8592, HI-8593, HI-8594
FUNCTIONAL DESCRIPTION
Figure 1 is a block diagram of the line driver. The chip
requires a positive 5V supply at V+. The negative 5V
supply at V- may be from an external source or may be
provided using the on-chip negative rail generator by
connecting the two external capacitors, CFLY and COUT.
Currents for slope control are set by on-chip resistors.
The TX0IN and TX1IN inputs receive logic signals from
a control transmitter chip such as the HI-3584. TXAOUT and TXBOUT hold each side of the ARINC bus
at Ground until one of the inputs becomes a One. If for
example TX1IN goes high, a charging path is enabled to
5V on an “A” side internal capacitor while the “B” side is
enabled to -5V. The charging current is selected by the
SLP pin. If the SLP pin is high, the capacitor is nominally
charged from 10% to 90% in 1.5μs. If SLP is low, the
rise and fall times are 10μs.
The reduced pin-count HI-8593 and HI-8594 require an
external -5V supply.
slopes and differentially drives the ARINC line. Current is limited by the series output resistors at each pin.
There are no fuses at the outputs of the HI-859x family.
The HI-8593 has 37.5 ohms in series with each TXOUT
output and the HI-8594 has 5 ohms in series with each
AMP output. The AMP outputs are for applications
where external series resistance is required, typically
for lightning protection devices. Both output types are
available on the HI-8592. Holt Application Note AN-300
describes suitable lightning protection schemes.
All devices feature tri-stateable outputs to allow multiple
line drivers to be connected to the same ARINC 429
bus. Setting TX1IN and TX0IN both to a logic “1” puts
the outputs in the high-impedance state.
The HI-8592 family of line drivers are built using highspeed CMOS technology. Care should be taken to ensure the V+ and V- supplies are locally decoupled to reduce noise. An application example is shown in Figure
2.
A unity gain buffer receives the internally generated
ABSOLUTE MAXIMUM RATINGS
RECOMMENDED OPERATING
CONDITIONS
Supply Voltages
V+ ........................................................... +7V
Supply Voltages
V- ........................................................... -7V
V+ ................................... +4.85V to +5.25V
DC Current per input pin ................................... +10mA
V- ................................... -5.25V to -4.85V
o
Power Dissipation at 25 C
Temperature Range
o
plastic SOIC ........... 1.0W, derate 10mW/ C
o
ceramic DIP ......... 0.5W, derate 7mW/ C
o
Solder Temperature ......................... 275 C for 10sec
o
o
Storage Temperature ....................... -65 C to +150 C
o
o
Industrial Screening .............. -40 C to +85 C
o
o
Hi-Temp Screening .............. -55 C to +125 C
NOTE: Stresses above absolute maximum ratings or outside
recommended operating conditions may cause permanent
damage to the device. These are stress ratings only. Operation at the limits is not recommended.
Note: The HI-8592 family of drivers are available in small-footprint, thermally enhanced SOIC and QFN (chip-scale) packages. These packages include a metal heat sink located on
the bottom surface of the device. This heat sink should be
soldered down to the printed circuit board for optimum thermal
dissipation.
The heat sink is electrically isolated from the chip and can be
soldered to any ground or power plane.
HOLT INTEGRATED CIRCUITS
4
HI-8592, HI-8593, HI-8594
ELECTRICAL CHARACTERISTICS
Table 3. DC Electrical Characteristics
V+ = +5V, V- = -5V (HI-8593/4 only), TA = Operating Temperature Range (unless otherwise stated)
Parameters
Symbol
Test Conditions
Min
Typ
Max
Units
Input Voltage (TX1IN, TX0IN, SLP)
High
VIH
2.1
-
V+
V
Low
VIL
-
-
0.5
V
Input Current (TX1IN, TX0IN, SLP)
Source
IIH
VIN = 0V
-
-
0.1
μA
Sink
IIL
VIN = 5V
-
-
0.1
μA
one
VDIFF1
no load; TXAOUT - TXBOUT
9
10
11
V
zero
VDIFF0
no load; TXAOUT - TXBOUT
-11
-10
-9
V
null
VDIFFN
no load; TXAOUT - TXBOUT
-0.5
0
0.5
V
one or zero
VDOUT
no load & magnitude at pin
4.5
5.0
5.5
V
null
VNOUT
no load
-0.25
0
0.25
V
ARINC Output Voltage (Differential)
ARINC Output Voltage (Ref. to GND)
Operating Supply Current
SLP = V+
V+
IDD
TX1IN & TX0IN = 0V: no load
-
22
28
mA
GND
IGND
TX1IN & TX0IN = 0V: no load
-
10
16
mA
V-
IEE
TX1IN & TX0IN = 0V: no load
-16
-10
-
mA
ARINC Output Impedance
ZOUT
TXOUT pins
37.5
Ohms
AMP pins
5
Ohms
ARINC Output Tri-State Current
IOZ
V- < VOUT < V+, TA = 125oC
TX0IN = TX1IN = V+
HOLT INTEGRATED CIRCUITS
5
-1.0
0
+1.0
μA
HI-8592, HI-8593, HI-8594
Table 4. Converter Characteristics
V+ = +5V, V- = -5V (HI-8593/4 only), TA = Operating Temperature Range (unless otherwise stated)
Parameters
Start-up transient (V+, V-)
Operating Switching Frequency
Symbol
Min
Typ
Max
Units
tSTART
-
-
10
ms
fsw
425
550
670
kHz
2.2
4.7
-
μF
22
47
-
μF
47
68
-
μF
CFLY
Recommended Capacitors
Test Conditions
COUT / CFLY >= 10
COUT
CSUPPLY
CSUPPLY >= COUT (connect from
V+ to GND)
Table 5. AC Electrical Characteristics
V+ = +5V, V- = -5V (HI-8593/4 only), TA = Operating Temperature Range (unless otherwise stated)
Parameters
Symbol
Line Driver Propogation Delay
Test Conditions
Min
Typ
Max
Units
defined in Figure 2, no load
Output high to low
tphlx
-
500
-
ns
Output low to high
tplhx
-
500
-
ns
Line Driver Transition Times
High Speed
SLP = V+
Output high to low
tfx
pin 1 = logic 1
1.0
1.5
2.0
μs
Output low to high
trx
pin 1 = logic 1
1.0
1.5
2.0
μs
Low Speed
SLP = V+
Output high to low
tfx
pin 1 = logic 0
5.0
10.0
15.0
μs
Output low to high
trx
pin 1 = logic 0
5.0
10.0
15.0
μs
-
-
10
pF
-
-
1.5
pF
Input Capacitance (Logic)1
Output Capacitance (Tri-state)1
CIN
COUT
TX0IN = TX1IN = V+
Notes:
1. Guaranteed but not tested
HOLT INTEGRATED CIRCUITS
6
HI-8592, HI-8593, HI-8594
5V
TX1IN
0V
tphlx
tplhx
tplhx
5V
TX0IN
0V
tphlx
trx
trx
VDIFF
(TXAOUT - TXBOUT)
10%
10V
90%
0V
10%
90%
-10V
10%
tfx
tfx
Figure 3. Line Driver Timing
PACKAGE THERMAL CHARACTERISTICS
Maximum ARINC LOAD
Package Style1
14-Lead Plastic
ESOIC5
ARINC 429
Data Rate
Junction Temp, Tj (oC)
Supply Current (mA)2
TA = 25oC
TA = 85oC
TA = 125oC TA = 25oC
TA = 85oC
TA = 125oC
Low Speed3
30
31
32
33
93
134
High Speed4
36
36
37
35
95
135
TXAOUT and TXBOUT Shorted to Ground6,7,8
Package Style1
14-Lead Plastic
ESOIC5
ARINC 429
Data Rate
Junction Temp, Tj (oC)
Supply Current (mA)2
TA = 25oC
TA = 85oC
TA = 125oC TA = 25oC
TA = 85oC
TA = 125oC
Low Speed3
89
82
77
53
111
149
High Speed4
87
81
77
52
111
149
Notes:
1.
All data taken in still air.
2.
At 100% duty cycle, 5V power supplies.
3.
Low Speed: Data Rate = 12.5 Kbps, Load: R = 400 Ohms, C = 30 nF.
4.
High Speed: Data Rate = 100 Kbps, Load: R = 400 Ohms, C = 10 nF. Data not presented for C = 30 nF as this is considered unrealistic for
high speed operation.
5.
14 Lead Plastic ESOIC (Thermally enhanced SOIC with built in heat sink). Heat sink not soldered.
6.
Similar results would be obtained with TXAOUT shorted to TXBOUT.
7.
For applications requiring survival with continuous short circuit, operation above Tj = 175°C is not recommended.
8.
Data will vary depending on air flow and the method of heat sinking employed.
HOLT INTEGRATED CIRCUITS
7
HI-8592, HI-8593, HI-8594
ORDERING INFORMATION
HI - 8592xx x x
PART NUMBER
LEAD FINISH
Blank
Tin / Lead (Sn / Pb) Solder
F
100% Matte Tin (Pb-free, RoHS compliant)
PART NUMBER
TEMPERATURE RANGE
o
o
FLOW
BURN IN
I
-40 C to +85 C
I
No
T
-55oC to +125oC
T
No
M
Yes
M
PART NUMBER
o
o
-55 C to +125 C
PACKAGE DESCRIPTION
PS
14 PIN PLASTIC SMALL OUTLINE - NB ESOIC (14HNE)
PC
24 PIN PLASTIC QFN (24PCS)
CR
14 PIN CERDIP (14D). NOTE: Not Available Pb-Free
HI - 859x xx x x
PART NUMBER
Blank
Tin / Lead (Sn / Pb) Solder
F
100% Matte Tin (Pb-free, RoHS compliant)
PART NUMBER
I
-40oC to +85oC
o
o
FLOW
BURN IN
I
No
-55 C to +125 C
T
No
M
-55oC to +125oC
M
Yes
PACKAGE DESCRIPTION
PS
8 PIN PLASTIC SMALL OUTLINE - NB ESOIC (8HNE)
CR
8 PIN CERDIP (8D). NOTE: Not Available Pb-Free
PART NUMBER
-
TEMPERATURE RANGE
T
PART NUMBER
Legend: ESOIC
NB
LEAD FINISH
OUTPUT RESISTANCE
8593
37.5 Ohms
8594
5 Ohms
Thermally enhanced Small Outline Package (SOIC with built-in heat sink)
Narrow Body
HOLT INTEGRATED CIRCUITS
8
HI-8592, HI-8593, HI-8594
ADDITIONAL PIN CONFIGURATIONS
NOTE: All power and ground pins must be connected.
14 AMPB
V+ 1
SLP 1
8 V+
13 TXBOUT
TX0IN 2
7 TXBOUT
TX0IN 3
12 AMPA
TX1IN 3
6 TXAOUT
TX1IN 4
11 TXAOUT
GND 4
10 V-
CAP+ 6
9 GND
CAP- 7
8 V+
5 V-
HI-8593CR
8-PIN CERDIP
GND 4
5 V-
HI-8594CR
8-PIN CERDIP
20 -
22 V+
16 TXAOUT
GND 4
15 V-
GND 5
14 V-
CAP+ 6
13 GND
V+ 11
6 AMPA
V+ 10
TX1IN 3
17 AMPA
TX1IN 3
CAP- 9
7 AMPB
21 V+
24 TX0IN 2
18 TXBOUT
- 1
TX0IN 2
- 7
8 V+
- 8
SLP 1
23 SLP
HI-8592CR
14-PIN CERDIP
19 AMPB
GND 5
GND 12
SLP 2
HI-8592PC
24-LEAD 5mm x 5mm QFN
HOLT INTEGRATED CIRCUITS
9
HI-8592, HI-8593, HI-8594
REVISION HISTORY
Revision
DS8592,
Date
Description of Change
Rev. NEW
6/21/10
Initial Release
Rev. A
7/1/10
Corrected typo in features (no “fixed” rise and fall time)
Rev. B
10/28/10
Rev. A had incorrect package drawing (SOIC-8). Replaced with correct ESOIC-8.
HOLT INTEGRATED CIRCUITS
10
HI-8592, HI-8593, HI-8594
PACKAGE DIMENSIONS
inches (millimeters)
14-PIN PLASTIC SMALL OUTLINE (ESOIC) - NB
(Narrow Body, Thermally Enhanced)
.0085 ± .001
(.220 ± .029)
.341 ± .004
(8.65 ± .10)
.236 ± .008
(6.00 ± .20)
Top View
Package TYPE: 14HNE
.270 typ
(6.86)
Bottom
View
.100 typ
(2.54)
.153 ± .003
(3.87 ± .06)
See Detail A
.0165 ± .003
(.419 ± .089)
Electrically isolated heat sink
pad on bottom of package.
Connect to any ground or
power plane for optimum
thermal dissipation.
.055 ± .005
(1.397 ± .13)
.050 BSC
(1.27)
0o to 8o
.033 ± .017
(.838 ± .43)
BSC = “Basic Spacing between Centers”
is theoretical true position dimension and
has no tolerance. (JEDEC Standard 95)
.0025 ± .0015
(.0635 ± .04)
Detail A
8-PIN PLASTIC SMALL OUTLINE (ESOIC) - NB
(Narrow Body, Thermally Enhanced)
Top View
.236 ± .008
(5.99 ± .21)
PIN 1
Package Type: 8HNE
Bottom
View
.0085 ± .0015
(.216 ± .038)
.194 ± .004
(4.92 ± .09)
inches (millimeters)
.140 ± .01
(3.56 ± .26)
.100 ± .01
(2.54 ± .25)
.154 ± .004
(3.90 ± .09)
.0165 ± .003
(.419 ± .089)
See Detail A
.055 ± .005
(1.397 ± .127)
Electrically isolated heat sink
pad on bottom of package.
Connect to any ground or
power plane for optimum
thermal dissipation.
0o to 8o
BSC = “Basic Spacing between Centers”
is theoretical true position dimension and
has no tolerance. (JEDEC Standard 95)
.050 BSC
(1.27)
.033 ± .017
(.838 ± .432)
.0025 ± .002
(.064 ± .038)
Detail A
HOLT INTEGRATED CIRCUITS
11
HI-8592, HI-8593, HI-8594
14-PIN CERDIP
inches (millimeters)
Package Type: 14D
.050 max
(1.27 max)
.767 max
(19.48 max)
.005 min
(.127 min)
.288 + .003
(7.32 + .08)
.056 typ
(1.422 typ)
.100
BSC
(2.54)
.200 max
(5.080 max)
.310 + .010
(7.874 + .254)
.180 max
(4.572 max)
.015 min
(.381 min)
.018 + .003
(.457 + .760)
.125 min
(3.175 min)
0o to 15o
.010 + .002
(.254 + .051)
8-PIN CERDIP
Package Type: 8D
.380 ± .004
(9.652 ± .102)
.005 MIN.
(.127 MIN.)
.248 ± .003
(6.299 ± .076)
.039 ± .006
(.991 ± .154)
.100 ± .008
(2.540 ± .203)
.015 MIN.
(.381 MIN.)
.200 MAX.
(5.080 MAX.)
.314 ± .003
(7.976 ± .076)
Base Plane
.010 ± .006
(.254 ± .152)
Seating Plane
.163 ± .037
(4.140 ± .940)
.056 ± .006
(1.422 ± .152)
.018 ± .006
(.457 ± .152)
HOLT INTEGRATED CIRCUITS
12
.350 ± .030
(8.890 ± .762)
HI-8592, HI-8593, HI-8594
24-PIN PLASTIC CHIP-SCALE PACKAGE (QFN)
millimeters
Package Type: 24PCS
5.00 + .05
Heat sink pad on bottom of
package. Heat sink can float
or can be connected to V+.
DO NOT connect heat sink to
GND
3.65 + .15
0.65 BSC
5.00 + .05
Top View
Bottom
View
3.65 + .15
0.35 typ.
0.45 typ.
0.93 max
0.025 max
BSC = “Basic Spacing between Centers”
is theoretical true position dimension and
has no tolerance. (JEDEC Standard 95)
HOLT INTEGRATED CIRCUITS
13
Similar pages