Cadeka CDK1308CILP40 Ultra low power, 20/40/65/80msps, 10-bit analog-to-digital converters (adcs) Datasheet

ADVANCE Data Sheet
A m p l i fy t h e H u m a n E x p e r i e n c e
CDK1308
Ultra Low Power, 20/40/65/80MSPS,
10-bit Analog-to-Digital Converters (ADCs)
n
10-bit resolution
n
20/40/65/80MSPS max sampling rate
n
The CDK1308 is a high performance ultra low power analog-to-digital
converter (ADC). The ADC employs internal reference circuitry, a CMOS
control interface and CMOS output data, and is based on a proprietary
structure. Digital error correction is employed to ensure no missing codes in
the complete full scale range.
Ultra-Low Power Dissipation:
15/25/38/46mW
n
61.6dB SNR at 8MHz FIN
n
Internal reference circuitry
n
1.8V core supply voltage
n
1.7 – 3.6V I/O supply voltage
n
Parallel CMOS output
n
40-pin QFN package
n
Pin compatible with CDK1307
Two idle modes with fast startup times exist. The entire chip can either be
put in Standby Mode or Power Down mode. The two modes are optimized to
allow the user to select the mode resulting in the smallest possible energy
consumption during idle mode and startup.
The CDK1308 has a highly linear THA optimized for frequencies up to Nyquist.
The differential clock interface is optimized for low jitter clock sources and
supports LVDS, LVPECL, sine wave, and CMOS clock inputs.
APPLICATIONS
n
Medical Imaging
n
Portable Test Equipment
n
Digital Oscilloscopes
n
IF Communication
Functional Block Diagram
Rev 0.1
10
Ordering Information
Part Number
Speed
Package
Pb-Free
RoHS Compliant
Operating Temperature Range
Packaging Method
CDK1308AILP40
20MSPS
QFN-40
Yes
Yes
-40°C to +85°C
Tray
CDK1308BILP40
20MSPS
QFN-40
Yes
Yes
-40°C to +85°C
Tray
CDK1308CILP40
65MSPS
QFN-40
Yes
Yes
-40°C to +85°C
Tray
CDK1308DILP40
80MSPS
QFN-40
Yes
Yes
-40°C to +85°C
Tray
Moisture sensitivity level for all parts is MSL-3.
©2008 CADEKA Microcircuits LLC CDK1308 Ultra Low Power, 20/40/65/80MSPS, 10-bit ADCs
General Description
FEATURES
www.cadeka.com
ADVANCE Data Sheet
Pin Configuration
SLP_N
CM_EXTBC_0
CM_EXTBC_1
OVDD
OVDD
D_9
D_8
D_7
D_6
D_5
39
38
37
36
35
34
33
32
31
DVSS
1
30
D_4
CM_EXT
2
29
D_3
AVDD
3
28
D_2
AVDD
4
27
CLK_EXT
IP
5
26
OVDD
IN
6
25
OVDD
AVDD
7
24
ORNG
DVDDCLK
8
23
D_1
CLKP
9
22
D_0
CLKN
10
21
NC
CDK1308
11
12
13
14
15
16
17
18
19
20
DVDD
CLK_EXT_EN
DFRMT
PD_N
OE_N
DVDD
OVDD
OVDD
NC
NC
QFN-40
CDK1308 Ultra Low Power, 20/40/65/80MSPS, 10-bit ADCs
40
QFN-40
Pin Assignments
Pin No.
Pin Name
0
VSS
1, 11, 16
DVDD
2
CM_EXT
3, 4, 7
AVDD
Analog supply voltage, 1.8V
5, 6
IP, IN
Analog input (non-inverting, inverting)
8
DVDDCLK
9
CLKP
Clock input, non-inverting (format: LVDS, LVPECL, CMOS/TTL, Sine Wave)
10
CLKN
Clock input, inverting. For CMOS input on CLKP, connect CLKN to ground
12
CLK_EXT_EN
CLK_EXT signal enabled when low (zero). Tristate when high.
13
DFRMT
Data format selection. 0: Offset Binary, 1: Two's Complement
14
PD_N
Full chip Power Down mode when Low. All digital outputs reset to zero. After chip power up
always apply Power Down mode before using Active Mode to reset chip.
15
OE_N
Output Enable. Tristate when high
17, 18, 25,
26, 36, 37
OVDD
I/O ring post-driver supply voltage. Voltage range 1.7 to 3.6V
19
NC
20
NC
21
NC
22
D_0
Ground connection for all power domains. Exposed pad
Digital and I/O-ring pre driver supply voltage, 1.8V
Common Mode voltage output
Rev 0.1
©2008 CADEKA Microcircuits LLC Description
Clock circuitry supply voltage, 1.8V
Output Data
www.cadeka.com
2
ADVANCE Data Sheet
Pin Assignments (Continued)
Pin No.
Description
23
D_1
Output Data
24
ORNG
Out of Range flag. High when input signal is out of range
27
CK_EXT
Output clock signal for data synchronization. CMOS levels
28
D_2
Output Data
29
D_3
Output Data
30
D_4
Output Data
31
D_5
Output Data
32
D_6
Output Data
33
D_7
Output Data
34
D_8
Output Data
35
D_9
Output Data (MSB)
38, 39
CM_EXTBC_1,
CM_EXTBC_0
40
SLP_N
CDK1308 Ultra Low Power, 20/40/65/80MSPS, 10-bit ADCs
Pin Name
Bias control bits for the buffer driving pin CM_EXT
00: OFF
10: 50μA
10: 500μA
11: 1mA
Sleep Mode when low
Rev 0.1
©2008 CADEKA Microcircuits LLC www.cadeka.com
3
ADVANCE Data Sheet
Absolute Maximum Ratings
The safety of the device is not guaranteed when it is operated above the “Absolute Maximum Ratings”. The device
should not be operated at these “absolute” limits. Adhere to the “Recommended Operating Conditions” for proper device
function. The information contained in the Electrical Characteristics tables and Typical Performance plots reflect the
operating conditions noted on the tables and plots.
Min
Max
Unit
AVDD
DVDD
AVSS, DVSSCK, DVSS, OVSS
OVDD
CLKP, CLKN
Analog inputs and outpts (IPx, INx)
Digital inputs
Digital outputs
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
+2.3
+2.3
+0.3
+3.9
+3.9
+2.3
+3.9
+3.9
V
V
V
V
V
V
V
V
CDK1308 Ultra Low Power, 20/40/65/80MSPS, 10-bit ADCs
Parameter
Reliability Information
Parameter
Junction Temperature
Storage Temperature Range
Lead Temperature (Soldering, 10s)
Min
Typ
-60
Max
Unit
TBD
+150
°C
°C
°C
TBD
ESD Protection
Product
QFN-40
Human Body Model (HBM)
Charged Device Model (CDM)
2kV
TBD
Recommended Operating Conditions
Parameter
Min
Operating Temperature Range
-40
Typ
Max
Unit
+85
°C
Rev 0.1
©2008 CADEKA Microcircuits LLC www.cadeka.com
4
ADVANCE Data Sheet
Electrical Characteristics
(AVDD = 1.8V, DVDD = 1.8V, DVDDCLK = 1.8V, OVDD = 2.5V, 20/40/65/80MSPS clock, 50% clock duty cycle,
-1dBFS 8MHz input signal, unless otherwise noted)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
DC Accuracy
Guaranteed
Offset Error
Midscale offset
Gain Error
Full scale range deviation from typical
TBD
mV
-6
6
%FS
DNL
Differential Non-Linearity
-0.3
0.3
LSB
INL
Integral Non-Linearity
-0.6
0.6
LSB
VCMO
Common Mode Voltage Output
VAVDD/2
V
Analog Input
VCMI
Input Common Mode
Analog input common mode voltage
VCM -0.1
VCM +0.1
V
VFSR
Full Scale Range
Differential input voltage range
2.0
Input Capacitance
Differential input capacitance
1.8
Bandwidth
Input bandwidth, full power
500
AVDD,
DVDD
Core Supply Voltage
Supply voltage to all 1.8V domain pins.
See Pin Configuration and Description
1.7
1.8
2.0
V
2.5
3.6
V
I/O Supply Voltage
Output driver supply voltage (OVDD).
Must be higher than or equal to Core Supply
Voltage (VOVDD ≥ VOCVDD)
1.7
OVDD
Vpp
pF
MHz
Power Supply
CDK1308 Ultra Low Power, 20/40/65/80MSPS, 10-bit ADCs
No Missing Codes
Rev 0.1
©2008 CADEKA Microcircuits LLC www.cadeka.com
5
ADVANCE Data Sheet
Electrical Characteristics - CDK1308A
(AVDD = 1.8V, DVDD = 1.8V, DVDDCLK = 1.8V, OVDD = 2.5V, 20MSPS clock, 50% clock duty cycle,
-1dBFS 8MHz input signal, unless otherwise noted)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Performance
SINAD
SFDR
HD2
HD3
ENOB
Signal to Noise Ratio
Signal to Noise and Distortion Ratio
Spurious Free Dynamic Range
Second order Harmonic Distortion
Third order Harmonic Distortion
Effective number of Bits
61.7
dBFS
FIN = 8MHz
61.6
dBFS
FIN ≃ FS/2
61.6
dBFS
FIN = 20MHz
61.6
dBFS
FIN = 2MHz
61.7
dBFS
FIN = 8MHz
61.6
dBFS
FIN ≃ FS/2
60.5
dBFS
FIN = 20MHz
61.6
dBFS
FIN = 2MHz
84.1
dBc
FIN = 8MHz
85.5
dBc
FIN ≃ FS/2
70.3
dBc
FIN = 20MHz
87.5
dBc
FIN = 2MHz
-88.8
dBc
FIN = 8MHz
-89.5
dBc
FIN ≃ FS/2
-95.9
dBc
FIN = 20MHz
-91.4
dBc
FIN = 2MHz
-89.5
dBc
FIN = 8MHz
-90.5
dBc
FIN ≃ FS/2
-70.3
dBc
FIN = 20MHz
-89.7
dBc
FIN = 2MHz
10.0
bits
FIN = 8MHz
9.9
bits
FIN ≃ FS/2
9.8
bits
FIN = 20MHz
9.9
bits
Power Supply
AIDD
Analog Supply Current
DIDD
Digital Supply Current
Output Driver Supply
mA
1.0
mA
2.5V output driver supply, sine wave input,
FIN = 1MHz, CLK_EXT enabled
1.7
mA
2.5V output driver supply, sine wave input,
FIN = 1MHz, CLK_EXT disabled
1.2
mA
Analog Power Dissipation
10.1
mW
Digital Power Dissipation
OVDD = 2.5V, 5pF load on output bits,
FIN = 1MHz, CLK_EXT disabled
4.8
mW
Total Power Dissipation
OVDD = 2.5V, 5pF load on output bits,
FIN = 1MHz, CLK_EXT disabled
14.9
mW
Power Down Dissipation
Sleep Mode
Power Dissipation, Sleep mode
9.9
µW
7.7
mW
Rev 0.1
OIDD
5.6
Digital core supply
Clock Inputs
Max. Conversion Rate
Min. Conversion Rate
©2008 CADEKA Microcircuits LLC 20
MSPS
15
MSPS
www.cadeka.com
CDK1308 Ultra Low Power, 20/40/65/80MSPS, 10-bit ADCs
SNR
FIN = 2MHz
6
ADVANCE Data Sheet
Electrical Characteristics - CDK1308B
(AVDD = 1.8V, DVDD = 1.8V, DVDDCLK = 1.8V, OVDD = 2.5V, 40MSPS clock, 50% clock duty cycle,
-1dBFS 8MHz input signal, unless otherwise noted)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Performance
SINAD
SFDR
HD2
HD3
ENOB
Signal to Noise Ratio
Signal to Noise and Distortion Ratio
Spurious Free Dynamic Range
Second order Harmonic Distortion
Third order Harmonic Distortion
Effective number of Bits
61.6
dBFS
FIN = 8MHz
61.6
dBFS
FIN ≃ FS/2
61.6
dBFS
FIN = 30MHz
61.5
dBFS
FIN = 2MHz
61.6
dBFS
FIN = 8MHz
61.6
dBFS
FIN ≃ FS/2
61.2
dBFS
FIN = 30MHz
61.4
dBFS
FIN = 2MHz
78.8
dBc
FIN = 8MHz
82.3
dBc
FIN ≃ FS/2
72.0
dBc
FIN = 30MHz
82.5
dBc
FIN = 2MHz
-87.9
dBc
FIN = 8MHz
-92.0
dBc
FIN ≃ FS/2
-84.8
dBc
FIN = 30MHz
-88.8
dBc
FIN = 2MHz
-81.8
dBc
FIN = 8MHz
-85.7
dBc
FIN ≃ FS/2
-72.0
dBc
FIN = 30MHz
-83.9
dBc
FIN = 2MHz
9.9
bits
FIN = 8MHz
9.9
bits
FIN ≃ FS/2
9.9
bits
FIN = 30MHz
9.9
bits
Power Supply
AIDD
Analog Supply Current
DIDD
Digital Supply Current
Output Driver Supply
mA
1.7
mA
2.5V output driver supply, sine wave input,
FIN = 1MHz, CLK_EXT enabled
3.1
mA
2.5V output driver supply, sine wave input,
FIN = 1MHz, CLK_EXT disabled
2.2
mA
Analog Power Dissipation
16.7
mW
Digital Power Dissipation
OVDD = 2.5V, 5pF load on output bits,
FIN = 1MHz, CLK_EXT disabled
8.6
mW
Total Power Dissipation
OVDD = 2.5V, 5pF load on output bits,
FIN = 1MHz, CLK_EXT disabled
25.3
mW
9.7
µW
Power Dissipation, Sleep mode
11.3
mW
Power Down Dissipation
Sleep Mode
Rev 0.1
OIDD
9.3
Digital core supply
Clock Inputs
Max. Conversion Rate
Min. Conversion Rate
©2008 CADEKA Microcircuits LLC 40
MSPS
20
MSPS
www.cadeka.com
CDK1308 Ultra Low Power, 20/40/65/80MSPS, 10-bit ADCs
SNR
FIN = 2MHz
7
ADVANCE Data Sheet
Electrical Characteristics - CDK1308C
(AVDD = 1.8V, DVDD = 1.8V, DVDDCLK = 1.8V, OVDD = 2.5V, 65MSPS clock, 50% clock duty cycle,
-1dBFS 8MHz input signal, unless otherwise noted)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Performance
SINAD
SFDR
HD2
HD3
ENOB
Signal to Noise Ratio
Signal to Noise and Distortion Ratio
Spurious Free Dynamic Range
Second order Harmonic Distortion
Third order Harmonic Distortion
Effective number of Bits
61.6
dBFS
FIN = 20MHz
61.6
dBFS
FIN ≃ FS/2
61.5
dBFS
FIN = 40MHz
61.3
dBFS
FIN = 8MHz
61.6
dBFS
FIN = 20MHz
61.6
dBFS
FIN ≃ FS/2
60.4
dBFS
FIN = 40MHz
61.1
dBFS
FIN = 8MHz
80.6
dBc
FIN = 20MHz
85.6
dBc
FIN ≃ FS/2
66.4
dBc
FIN = 40MHz
76.9
dBc
FIN = 8MHz
-91.4
dBc
FIN = 20MHz
-93.0
dBc
FIN ≃ FS/2
-83.8
dBc
FIN = 40MHz
-90.7
dBc
FIN = 8MHz
-80.6
dBc
FIN = 20MHz
-86.4
dBc
FIN ≃ FS/2
-66.4
dBc
FIN = 40MHz
-76.9
dBc
FIN = 8MHz
9.9
bits
FIN = 20MHz
9.9
bits
FIN ≃ FS/2
9.7
bits
FIN = 40MHz
9.9
bits
Power Supply
AIDD
Analog Supply Current
DIDD
Digital Supply Current
mA
2.6
mA
2.5V output driver supply, sine wave input,
FIN = 1MHz, CLK_EXT enabled
4.9
mA
2.5V output driver supply, sine wave input,
FIN = 1MHz, CLK_EXT disabled
3.4
mA
24.8
mW
Digital Power Dissipation
OVDD = 2.5V, 5pF load on output bits,
FIN = 1MHz, CLK_EXT disabled
13.2
mW
Total Power Dissipation
OVDD = 2.5V, 5pF load on output bits,
FIN = 1MHz, CLK_EXT disabled
38.0
mW
9.3
µW
Power Dissipation, Sleep mode
15.7
mW
Output Driver Supply
Analog Power Dissipation
Power Down Dissipation
Sleep Mode
Rev 0.1
OIDD
13.8
Digital core supply
Clock Inputs
Max. Conversion Rate
Min. Conversion Rate
©2008 CADEKA Microcircuits LLC 65
MSPS
40
MSPS
www.cadeka.com
CDK1308 Ultra Low Power, 20/40/65/80MSPS, 10-bit ADCs
SNR
FIN = 8MHz
8
ADVANCE Data Sheet
Electrical Characteristics - CDK1308D
(AVDD = 1.8V, DVDD = 1.8V, DVDDCLK = 1.8V, OVDD = 2.5V, 80MSPS clock, 50% clock duty cycle,
-1dBFS 8MHz input signal, unless otherwise noted)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Performance
SINAD
SFDR
HD2
HD3
ENOB
Signal to Noise Ratio
Signal to Noise and Distortion Ratio
Spurious Free Dynamic Range
Second order Harmonic Distortion
Third order Harmonic Distortion
Effective number of Bits
61.6
dBFS
FIN = 20MHz
61.2
dBFS
FIN = 30MHz
61.3
dBFS
FIN ≃ FS/2
61.3
dBFS
FIN = 8MHz
61.3
dBFS
FIN = 20MHz
60.7
dBFS
FIN = 30MHz
61.0
dBFS
FIN ≃ FS/2
58.7
dBFS
FIN = 8MHz
74.8
dBc
FIN = 20MHz
73.9
dBc
FIN = 30MHz
74.7
dBc
FIN ≃ FS/2
61.7
dBc
FIN = 8MHz
-88.5
dBc
FIN = 20MHz
-95.0
dBc
FIN = 30MHz
-88.9
dBc
FIN ≃ FS/2
-79.0
dBc
FIN = 8MHz
-74.8
dBc
FIN = 20MHz
-75.0
dBc
FIN = 30MHz
-74.7
dBc
FIN ≃ FS/2
-61.7
dBc
FIN = 8MHz
9.9
bits
FIN = 20MHz
9.8
bits
FIN = 30MHz
9.8
bits
FIN ≃ FS/2
9.5
bits
Power Supply
AIDD
Analog Supply Current
DIDD
Digital Supply Current
mA
3.3
mA
2.5V output driver supply, sine wave input,
FIN = 1MHz, CLK_EXT enabled
5.9
mA
2.5V output driver supply, sine wave input,
FIN = 1MHz, CLK_EXT disabled
4.1
mA
29.7
mW
Digital Power Dissipation
OVDD = 2.5V, 5pF load on output bits,
FIN = 1MHz, CLK_EXT disabled
16.2
mW
Total Power Dissipation
OVDD = 2.5V, 5pF load on output bits,
FIN = 1MHz, CLK_EXT disabled
45.9
mW
9.1
µW
Power Dissipation, Sleep mode
18.3
mW
Output Driver Supply
Analog Power Dissipation
Power Down Dissipation
Sleep Mode
Rev 0.1
OIDD
16.5
Digital core supply
Clock Inputs
Max. Conversion Rate
Min. Conversion Rate
©2008 CADEKA Microcircuits LLC 80
MSPS
65
MSPS
www.cadeka.com
CDK1308 Ultra Low Power, 20/40/65/80MSPS, 10-bit ADCs
SNR
FIN = 8MHz
9
ADVANCE Data Sheet
Digital and Timing Electrical Characteristics
(AVDD = 1.8V, DVDD = 1.8V, DVDDCLK = 1.8V, OVDD = 2.5V, 20/40/65/80MSPS clock, 50% clock duty cycle,
-1 dBFS input signal, 5pF capacitive load, unless otherwise noted)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
80
% high
Clock Inputs
20
Compliance
CMOS, LVDS, LVPECL, Sine Wave
Differential input swing
-200
200
mVpp
Differential input swing, sine wave clock input
-800
800
mVpp
Input Common Mode Voltage
Keep voltages within ground and voltage of OVDD
0.3
VOVDD -0.3
V
Input Capacitance
Differential
TPD
Start Up Time from Power Down
From Power Down Mode to Active Mode
References has reached 99% of final value
TSLP
Start Up Time from Sleep
From Sleep Mode to Active Mode
TOVR
Out Of Range Recovery Time
TAP
εRMS
Input Range
1.7
pF
Timing
900
clk cycles
0.5
µs
1
clk cycles
Aperture Delay
0.8
ns
Aperture Jitter
<0.5
ps
TLAT
Pipeline Delay
12
clk cycles
TD
Output Delay
TDC
Output Delay Relative to CLK_EXT
5pF load on output bits (see timing diagram)
4
10pF load on output bits (see timing diagram)
ns
TBD
See timing diagram
ns
2
ns
Logic Inputs
VIH
High Level Input Voltage
VOVDD ≥ 3.0V
VOVDD = 1.7V – 3.0V
VOVDD ≥ 3.0V
2
V
0.8 • VOVDD
V
0
0.8
V
VIL
Low Level Input Voltage
0
0.2 • VOVDD
V
IIH
High Level Input Leakage Current
-10
10
µA
IIL
Low Level Input Leakage Current
-10
10
µA
CI
Input Capacitance
VOVDD = 1.7V – 3.0V
3
pF
Logic Outputs
High Level Output Voltage
VOL
Low Level Output Voltage
CL
Max Capacitive Load
-0.1 +VOVDD
V
Post-driver supply voltage equal to pre-driver
supply voltage VOVDD = VOCVDD
Post-driver supply voltage above 2.25V (1)
0.1
V
5
pF
10
Rev 0.1
VOH
pF
Note:
(1) The outputs will be functional with higher loads. However, it is recommended to keep the load on output data bits as low as possible to keep dynamic currents
and resulting switching noise at a minimum.
©2008 CADEKA Microcircuits LLC www.cadeka.com
CDK1308 Ultra Low Power, 20/40/65/80MSPS, 10-bit ADCs
Duty Cycle
10
ADVANCE Data Sheet
N+3
N+4
N+5
N+2
N
N+1
CLK_EXT
Figure 1. Timing Diagram
Recommended Usage
DC-Coupling
Analog Input
Figure 3 shows a recommended configuration for DCcoupling. Note that the common mode input voltage must
be controlled according to specified values. Preferably, the
CM_EXT output should be used as a reference to set the
common mode voltage.
The analog inputs to the CDK1308 is a switched capacitor
track-and-hold amplifier optimized for differential operation. Operation at common mode voltages at mid supply
is recommended even if performance will be good for the
ranges specified. The CM_EXT pin provides a voltage suitable as common mode voltage reference. The internal
buffer for the CM_EXT voltage can be switched off, and
driving capabilities can be changed by using the CM_EXTBC control input.
Ω
Rev 0.1
Figure 2 shows a simplified drawing of the input network. The signal source must have sufficiently low output
impedance to charge the sampling capacitors within one
clock cycle. A small external resistor (e.g. 22Ω) in series
with each input is recommended as it helps reducing transient currents and dampens ringing behavior. A small differential shunt capacitor at the chip side of the resistors
may be used to provide dynamic charging currents and
may improve performance. The resistors form a low pass
filter with the capacitor, and values must therefore be determined by requirements for the application.
The input amplifier could be inside a companion chip or
it could be a dedicated amplifier. Several suitable single
ended to differential driver amplifiers exist in the market.
The system designer should make sure the specifications
of the selected amplifier is adequate for the total system,
and that driving capabilities comply with the CDK1308
input specifications.
pF
Ω
Figure 3. DC-Coupled Input
Detailed configuration and usage instructions must be
found in the documentation of the selected driver, and
the values given in Figure 3 must be varied according to
the recommendations for the driver.
AC-Coupling
Figure 2. Input Configuration
©2008 CADEKA Microcircuits LLC CDK1308 Ultra Low Power, 20/40/65/80MSPS, 10-bit ADCs
N-13
A signal transformer or series capacitors can be used
to make an AC-coupled input network. Figure 4 shows
www.cadeka.com
11
ADVANCE Data Sheet
33Ω
RT
47Ω
Note that startup time from Sleep Mode and Power Down
Mode will be affected by this filter as the time required
to charge the series capacitors is dependent on the filter
cut-off frequency.
If the input signal has a long traveling distance, and the kickbacks from the ADC not are effectively terminated at the
signal source, the input network of Figure 6 can be used.
The configuration is designed to attenuate the kickback
from the ADC and to provide an input impedance that looks
as resistive as possible for frequencies below Nyquist.
Values of the series inductor will however depend on board
design and conversion rate. In some instances a shunt
capacitor in parallel with the termination resistor (e.g. 33pF)
may improve ADC performance further. This capacitor
attenuate the ADC kick-back even more, and minimize the
kicks traveling towards the source. However, the impedance match seen into the transformer becomes worse.
120nH 33Ω
1:1
optional
RT
68Ω
220Ω
pF
120nH
33Ω
Figure 4. Transformer-Coupled Input
Ω
pF
Ω
Figure 5. AC-Coupled Input
©2008 CADEKA Microcircuits LLC Figure 6. Alternative Input Network
Rev 0.1
Figure 5 shows AC-coupling using capacitors. Resistors
from the CM_EXT output, RCM, should be used to bias the
differential input signals to the correct voltage. The series
capacitor, CI, form the high-pass pole with these resistors,
and the values must therefore be determined based on
the requirement to the high-pass cut-off frequency.
33Ω
Clock Input And Jitter Considerations
Typically high-speed ADCs use both clock edges to generate internal timing signals. In the CDK1308 only the rising
edge of the clock is used. Hence, input clock duty cycles
between 20% and 80% is acceptable.
The input clock can be supplied in a variety of formats.
The clock pins are AC-coupled internally, and hence a wide
common mode voltage range is accepted. Differential
clock sources as LVDS, LVPECL or differential sine wave
can be connected directly to the input pins. For CMOS
inputs, the CLKN pin should be connected to ground, and
the CMOS clock signal should be connected to CLKP. For
differential sine wave clock input the amplitude must be
at least ±800mVpp.
www.cadeka.com
CDK1308 Ultra Low Power, 20/40/65/80MSPS, 10-bit ADCs
a recommended configuration using a transformer. Make
sure that a transformer with sufficient linearity is selected,
and that the bandwidth of the transformer is appropriate.
The bandwidth should exceed the sampling rate of the
ADC with at least a factor of 10. It is also important to
keep phase mismatch between the differential ADC inputs
small for good HD2 performance. This type of transformer
coupled input is the preferred configuration for high frequency signals as most differential amplifiers do not have
adequate performance at high frequencies. If the input
signal is traveling a long physical distance from the signal
source to the transformer (for example a long cable), kickbacks from the ADC will also travel along this distance. If
these kick-backs are not terminated properly at the source
side, they are reflected and will add to the input signal at
the ADC input. This could reduce the ADC performance.
To avoid this effect, the source must effectively terminate
the ADC kick-backs, or the traveling distance should be
very short. If this problem could not be avoided, the circuit in Figure 6 can be used.
12
ADVANCE Data Sheet
The quality of the input clock is extremely important for
high-speed, high-resolution ADCs. The contribution to SNR
from clock jitter with a full scale signal at a given frequency
is shown in the equation below:
•
π • FIN • εt)
where FIN is the signal frequency, and εt is the total rms
jitter measured in seconds. The rms jitter is the total of all
jitter sources including the clock generation circuitry, clock
distribution and internal ADC circuitry.
For applications where jitter may limit the obtainable performance, it is of utmost importance to limit the clock
jitter. This can be obtained by using precise and stable
clock references (e.g. crystal oscillators with good jitter
specifications) and make sure the clock distribution is
well controlled. It might be advantageous to use analog
power and ground planes to ensure low noise on the supplies to all circuitry in the clock distribution. It is of utmost
importance to avoid crosstalk between the ADC output bits
and the clock and between the analog input signal and
the clock since such crosstalk often results in harmonic
distortion.
The jitter performance is improved with reduced rise and
fall times of the input clock. Hence, optimum jitter performance is obtained with LVDS or LVPECL clock with fast
edges. CMOS and sine wave clock inputs will result in
slightly degraded jitter performance.
Digital Outputs
Digital output data are presented on parallel CMOS form.
The digital outputs can be set in tristate mode by setting
the OE_N signal high.
The CDK1308 employs digital offset correction. This means
that the output code will be 4096 with shorted inputs.
However, small mismatches in parasitics at the input
can cause this to alter slightly. The offset correction also
results in possible loss of codes at the edges of the full
scale range. With no offset correction, the ADC would clip
in one end before the other, in practice resulting in code
loss at the opposite end. With the output being centered
digitally, the output will clip, and the out of range flags will
be set, before max code is reached. When out of range
flags are set, the code is forced to all ones for over-range
and all zeros for under-range.
Data Format Selection
The output data are presented on offset binary form
when DFRMT is low (connect to OVSS). Setting DFRMT
high (connect to OVDD) results in 2’s complement output
format. Details are shown in Table 1 below.
Table 1: Data Format Description for 2Vpp Full Scale Range
Output data: D_9 : D_0
Output Data: D_9 : D_0
(DFRMT = 0, offset binary)
(DFRMT = 1, 2’s complement)
1.0 V
11 1111 1111
01 1111 1111
+0.24mV
10 0000 0000
00 0000 0000
-0.24mV
01 1111 1111
11 1111 1111
-1.0V
00 0000 0000
10 0000 0000
Differential Input Voltage (IP - IN)
©2008 CADEKA Microcircuits LLC www.cadeka.com
13
Rev 0.1
If the clock is generated by other circuitry, it should be retimed with a low jitter master clock as the last operation
before it is applied to the ADC clock input.
The timing is described in the Timing Diagram section.
Note that the load or equivalent delay on CK_EXT always
should be lower than the load on data outputs to ensure
sufficient timing margins.
CDK1308 Ultra Low Power, 20/40/65/80MSPS, 10-bit ADCs
SNRjitter = 20 • log (2
The voltage on the OVDD pin set the levels of the CMOS
outputs. The output drivers are dimensioned to drive a
wide range of loads for OVDD above 2.25V, but it is recommended to minimize the load to ensure as low transient
switching currents and resulting noise as possible. In applications with a large fanout or large capacitive loads, it
is recommended to add external buffers located close to
the ADC chip.
ADVANCE Data Sheet
Reference Voltages
tributes to the Power Down Dissipation. The startup time
from this mode is longer than for Sleep Mode as all references need to settle to their final values before normal
operation can resume.
The SLP_N signal can be used to set the full chip in Sleep
Mode. In this mode internal clocking is disabled, but some
low bandwidth circuitry is kept on to allow for a short
startup time. However, Sleep Mode represents a significant reduction in supply current, and it can be used to
save power even for short idle periods.
Operational Modes
The operational modes are controlled with the PD_N and
SLP_N pins. If PD_N is set low, all other control pins are
overridden and the chip is set in Power Down mode. In
this mode all circuitry is completely turned off and the internal clock is disabled. Hence, only leakage current con-
The input clock should be kept running in all idle modes.
However, even lower power dissipation is possible in Power
Down mode if the input clock is stopped. In this case it is
important to start the input clock prior to enabling active mode.
Mechanical Dimensions
QFN-40 Package
D
D2
Pin 1 ID - Dia. 0.5
(Top Side)
1.14
Pin 1 ID - Dia. R
F
A
G
A3
0.45
A1
Pin 0 Exposed Pad
Symbol
A
A1
A2
A3
b
D
D1
D2
L
e
θ1
F
G
R
Min
–
0.001
–
0.008
0.156
0.012
0°
0.008
0.0096
0.004
Inches
Typ
–
0.0004
0.023
0.008 REF
0.010
0.236 BSC
0.226 BSC
0.162
0.016
0.020 BSC
–
–
0.0168
0.008
Max
0.035
0.002
0.028
Min
–
0.00
–
0.013
0.2
0.167
0.020
3.95
0.3
12°
–
0.024
–
0°
0.2
0.24
0.1
Millimeters
Typ
–
0.01
0.65
0.2 REF
0.25
6.00 BSC
5.75 BSC
4.10
0.4
0.50 BSC
–
–
0.42
0.2
Max
0.9
0.05
0.7
0.32
4.25
0.5
12°
–
0.6
–
NOTE:
D
D2
D1
Package dimensions in millimeter unless otherwise noted.
CDK1308 Ultra Low Power, 20/40/65/80MSPS, 10-bit ADCs
The reference voltages are internally generated and buffered based on a bandgap voltage reference. No external
decoupling is necessary, and the reference voltages are
not available externally. This simplifies usage of the ADC
since two extremely sensitive pins, otherwise needed, are
removed from the interface.
Rev 0.1
θ1
L
e
b
A2
For additional information regarding our products, please visit CADEKA at: cadeka.com
CADEKA Headquarters Loveland, Colorado
T: 970.663.5452
T: 877.663.5452 (toll free)
A m p l i fy t h e H u m a n E x p e r i e n c e
CADEKA, the CADEKA logo design, COMLINEAR and the COMLINEAR logo design are trademarks or registered trademarks of CADEKA
Microcircuits LLC. All other brand and product names may be trademarks of their respective companies.
CADEKA reserves the right to make changes to any products and services herein at any time without notice. CADEKA does not assume any
responsibility or liability arising out of the application or use of any product or service described herein, except as expressly agreed to in
writing by CADEKA; nor does the purchase, lease, or use of a product or service from CADEKA convey a license under any patent rights,
copyrights, trademark rights, or any other of the intellectual property rights of CADEKA or of third parties.
Copyright ©2008 by CADEKA Microcircuits LLC. All rights reserved.
designed by
Similar pages