HT11 THRU HT18 1.0 AMP. High Efficient Rectifiers Voltage Range 50 to 1000 Volts Current 1.0 Ampere TS-1 Features Low forward voltage drop High current capability High reliability High surge current capability Mechanical Data Case: Molded plastic TS-1 Epoxy: UL 94V-O rate flame retardant Lead: Axial leads, solderable per MIL-STD202, Method 208 guaranteed Polarity: Color band denotes cathode end High temperature soldering guaranteed: 260oC/10 seconds/.375”,(9.5mm) lead lengths at 5 lbs., (2.3kg) tension Mounting position: Any Weight: 0.20 gram Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol HT HT HT HT HT HT HT HT Units Type Number 11 12 13 14 15 16 17 18 Maximum Recurrent Peak Reverse Voltage 50 100 200 300 400 600 800 1000 V VRRM Maximum RMS Voltage V VRMS 35 70 140 210 280 420 560 700 Maximum DC Blocking Voltage 50 100 200 300 400 600 800 1000 V VDC Maximum Average Forward Rectified Current .375 (9.5mm) Lead Length @TA = 55℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 1.0A Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=100℃ I(AV) 1.0 A IFSM 30 A 1.0 VF Operating Temperature Range Storage Temperature Range TSTG Typical Junction Capacitance ( Note 2 ) Typical Thermal Resistance ( Note 3) 1.7 5.0 100 IR Trr Cj RθJA TJ Maximum Reverse Recovery Time ( Note 1 ) 1.3 50 20 75 15 100 -65 to +150 -65 to +150 Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C. 3. Mount on Cu-Pad Size 5mm x 5mm on PCB. - 310 - V uA uA nS pF ℃/W ℃ ℃ RATINGS AND CHARACTERISTIC CURVES (HT11 THRU HT18) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM FIG.2- MAXIMUM AVERAGE FORWARD CURRENT DERATING trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) 0 -0.25A (+) -1.0A NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 1cm FIG.3- TYPICAL REVERSE CHARACTERISTICS 2.0 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375" (9.5mm) Lead Length 1.0 0 0 25 50 75 100 125 150 175 o AMBIENT TEMPERATURE. ( C) FIG.4- TYPICAL FORWARD CHARACTERISTICS 100 INSTANTANEOUS FORWARD CURRENT. (A) 1000 INSTANTANEOUS REVERSE CURRENT. ( A) SET TIME BASE FOR 5/ 10ns/ cm AVERAGE FORWARD CURRENT. (A) 10W NONINDUCTIVE 50W NONINDUCTIVE 100 Tj=100 0C 10 Tj=75 0C 1 10 HT15 1 0.1 HT16~HT18 HT11~HT14 Tj=25 0C 0.1 0 0.01 20 40 60 80 100 120 140 0 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 70 35 60 30 8.3ms Single Half Sine Wave JEDEC Method 25 20 15 10 0 1 0.4 0.6 0.8 1.0 FORWARD VOLTAGE. (V) 1.2 1.4 FIG.6- TYPICAL JUNCTION CAPACITANCE 40 JUNCTION CAPACITANCE.(pF) PEAK FORWARD SURGE CURRENT. (A) FIG.5- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 0.2 50 40 HT 30 11~ H HT1 20 T15 6~H T18 10 0 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz 0.1 0.5 1 2 5 10 20 REVERSE VOLTAGE. (V) - 311 - 50 100 200 500 1000