LINER LTC1196-2ACS8-PBF 8-bit, so-8, 1msps adcs with auto-shutdown option Datasheet

LTC1196/LTC1198
8-Bit, SO-8, 1Msps ADCs
with Auto-Shutdown Options
FEATURES
DESCRIPTION
n
The LTC®1196/LTC1198 are 600ns, 8-bit A/D converters
with sampling rates up to 1MHz. They are offered in 8-pin
SO packages and operate on 3V to 6V supplies. Power
dissipation is only 10mW with a 3V supply or 50mW with
a 5V supply. The LTC1198 automatically powers down to a
typical supply current of 1nA whenever it is not performing
conversions. These 8-bit switched-capacitor successive
approximation ADCs include sample-and-holds. The
LTC1196 has a differential analog input; the LTC1198 offers a software selectable 2-channel MUX.
n
n
n
n
n
n
n
n
n
n
n
High Sampling Rates: 1MHz (LTC1196)
750kHz (LTC1198)
Low Cost
Single Supply 3V and 5V Specifications
Low Power: 10mW at 3V Supply
50mW at 5V Supply
Auto-Shutdown: 1nA Typical (LTC1198)
±1/2LSB Total Unadjusted Error over Temperature
3-Wire Serial I/O
1V to 5V Input Span Range (LTC1196)
Converts 1MHz Inputs to 7 Effective Bits
Differential Inputs (LTC1196)
2-Channel MUX (LTC1198)
SO-8 Plastic Package
These ADCs can be used in ratiometric applications or
with external references. The high impedance analog inputs and the ability to operate with reduced spans below
1V full scale (LTC1196) allow direct connection to signal
sources in many applications, eliminating the need for
gain stages.
APPLICATIONS
n
n
n
n
The 3-wire serial I/O, SO-8 packages, 3V operation and
extremely high sample rate-to-power ratio make these
ADCs an ideal choice for compact, high speed systems.
High Speed Data Acquisition
Disk Drives
Portable or Compact Instrumentation
Low Power or Battery-Operated Systems
The A grade devices are specified with total unadjusted
error of ±1/2LSB maximum over temperature.
L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
TYPICAL APPLICATION
Single 5V Supply, 1Msps, 8-Bit Sampling ADC
2
ANALOG INPUT
0V TO 5V RANGE
3
4
CS
+IN
–IN
GND
VCC
LTC1196
CLK
DOUT
VREF
8
7
6
SERIAL DATA LINK TO
ASIC, PLD, MPU, DSP,
OR SHIFT REGISTERS
5
1196/98 TA01
50
VREF = VCC = 2.7V
fSMPL = 383kHz (LTC1196)
fSMPL = 287kHz (LTC1198)
7
6
44
VREF = VCC = 5V
fSMPL = 1MHz (LTC1196)
fSMPL = 750kHz (LTC1198)
5
S/(N + D) (dB)
1
8
5V
EFFECTIVE NUMBER OF BITS (ENOBs)
1μF
Effective Bits and S/(N + D) vs Input Frequency
4
3
2
1
TA = 25°C
0
1k
10k
100k
INPUT FREQUENCY (Hz)
1M
1196/98 G24
119698fa
1
LTC1196/LTC1198
ABSOLUTE MAXIMUM RATINGS
(Notes 1, 2)
Supply Voltage (VCC) to GND .................................... 7V
Voltage
Analog Reference ....................... –0.3V to VCC + 0.3V
Digital Inputs ......................................... –0.3V to 7V
Digital Outputs ........................... –0.3V to VCC + 0.3V
Power Dissipation .............................................. 500mW
Operating Temperature Range
LTC1196-1AC, LTC1198-1AC, LTC1196-1BC,
LTC1198-1BC, LTC1196-2AC, LTC1198-2AC,
LTC1196-2BC, LTC1198-2BC ................. 0°C to 70°C
Storage Temperature Range.................. –65°C to 150°C
Lead Temperature (Soldering, 10 sec) ................ 300°C
PIN CONFIGURATION
LTC1196
LTC1198
TOP VIEW
CS 1
8
VCC
+IN 2
7
CLK
–IN 3
6
DOUT
GND 4
5
VREF
TOP VIEW
CS/ 1
SHUTDOWN
CH0 2
8
VCC (VREF)
7
CLK
CH1 3
6
DOUT
GND 4
5
DIN
S8 PACKAGE
8-LEAD PLASTIC SO
S8 PACKAGE
8-LEAD PLASTIC SO
TJMAX = 150°C, θJA = 175°C/W
TJMAX = 150°C, θJA = 175°C/W
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC1196-1ACS8#PBF
LTC1196-1ACS8#TRPBF
11961A
8-Lead Plastic SO
0°C to 70°C
LTC1196-1BCS8#PBF
LTC1196-1BCS8#TRPBF
11961B
8-Lead Plastic SO
0°C to 70°C
LTC1196-2ACS8#PBF
LTC1196-2ACS8#TRPBF
11962A
8-Lead Plastic SO
0°C to 70°C
LTC1196-2BCS8#PBF
LTC1196-2BCS8#TRPBF
11962B
8-Lead Plastic SO
0°C to 70°C
LTC1198-1ACS8#PBF
LTC1198-1ACS8#TRPBF
11981A
8-Lead Plastic SO
0°C to 70°C
LTC1198-1BCS8#PBF
LTC1198-1BCS8#TRPBF
11981B
8-Lead Plastic SO
0°C to 70°C
LTC1198-2ACS8#PBF
LTC1198-2ACS8#TRPBF
11982A
8-Lead Plastic SO
0°C to 70°C
LTC1198-2BCS8#PBF
LTC1198-2BCS8#TRPBF
11982B
8-Lead Plastic SO
0°C to 70°C
Consult LTC Marketing for parts specified with wider operating temperature ranges.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
119698fa
2
LTC1196/LTC1198
RECOMMENDED OPERATING CONDITIONS
The l denotes the specifications which apply over
SYMBOL
PARAMETER
LTC1196-1
LTC1198-1
TYP
VCC
Supply Voltage
the full operating temperature range, otherwise specifications are at TA = 25°C.
CONDITIONS
MIN
LTC1196-2
LTC1198-2
TYP
MAX
MAX
MIN
2.7
6
2.7
6
0.01
0.01
14.4
12.0
0.01
0.01
12.0
9.6
UNITS
V
VCC = 5V Operation
fCLK
Clock Frequency
tCYC
Total Cycle Time
l
LTC1196
LTC1198
MHz
MHz
12
16
12
16
CLK
CLK
tSMPL
Analog Input Sampling Time
2.5
2.5
CLK
thCS
Hold Time CS Low After Last CLK↑
10
13
ns
tsuCS
Setup Time CS↓ Before First CLK↑
(See Figures 1, 2)
20
26
ns
thDI
Hold Time DIN After CLK↑
LTC1198
20
26
ns
tsuDI
Setup Time DIN Stable Before CLK↑
LTC1198
20
26
ns
tWHCLK
CLK High Time
fCLK = fCLK(MAX)
40%
40%
1/fCLK
tWLCLK
CLK Low Time
fCLK = fCLK(MAX)
40%
40%
1/fCLK
tWHCS
CS High Time Between Data Transfer Cycles
25
32
ns
tWLCS
CS Low Time During Data Transfer
11
15
11
15
CLK
CLK
LTC1196
LTC1198
CONVERTER AND MULTIPLEXER CHARACTERISTICS
The l denotes the specifications
which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VCC = 5V, VREF = 5V, fCLK = fCLK(MAX)
as defined in Recommended Operating Conditions, unless otherwise noted.
PARAMETER
CONDITIONS
l
No Missing Codes Resolution
Offset Error
Linearity Error
(Note 3)
Full-Scale Error
Total Unadjusted Error (Note 4)
MIN
LTC1196, VREF = 5.000V
LTC1198, VCC = 5.000V
Analog and REF Input Range
LTC1196
Analog Input Leakage Current
(Note 5)
LTC1196-1
LTC1198-1
TYP
MAX
MIN
8
LTC1196-2
LTC1198-2
TYP
MAX
8
UNITS
Bits
l
±1/2
±1
LSB
l
±1/2
±1
LSB
l
±1/2
±1
LSB
l
±1/2
±1
LSB
±1
μA
–0.05V to VCC + 0.05V
l
±1
V
DIGITAL AND DC ELECTRICAL CHARACTERISTICS
The l denotes the specifications which
apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VCC = 5V, VREF = 5V, unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
VIH
High Level Input Voltage
VCC = 5.25V
l
VIL
Low Level Input Voltage
VCC = 4.75V
l
0.8
V
IIH
High Level Input Current
VIN = VCC
l
2.5
μA
IIL
Low Level Input Current
VIN = 0V
l
–2.5
μA
VOH
High Level Output Voltage
VCC = 4.75V, IO = 10μA
VCC = 4.75V, IO = 360μA
l
l
2.0
4.5
2.4
UNITS
V
4.74
4.71
V
V
119698fa
3
LTC1196/LTC1198
DIGITAL AND DC ELECTRICAL CHARACTERISTICS
The l denotes the specifications which
apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VCC = 5V, VREF = 5V, unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
VOL
Low Level Output Voltage
VCC = 4.75V, IO = 1.6mA
l
IOZ
Hi-Z Output Leakage
CS = High
l
ISOURCE
Output Source Current
VOUT = 0V
TYP
MAX
UNITS
0.4
V
±3
μA
–25
mA
ISINK
Output Sink Current
VOUT = VCC
IREF
Reference Current, LTC1196
CS = VCC
fSMPL = fSMPL(MAX)
l
l
0.001
0.5
45
3
1
mA
μA
mA
ICC
Supply Current
CS = VCC, LTC1198 (Shutdown)
CS = VCC, LTC1196
fSMPL = fSMPL(MAX), LTC1196/LTC1198
l
l
l
0.001
7
11
3
15
20
μA
mA
mA
DYNAMIC ACCURACY
The l denotes the specifications which apply over the full operating temperature range,
otherwise specifications are at TA = 25°C. VCC = 5V, VREF = 5V, fCLK = fCLK(MAX) as defined in Recommended Operating Conditions,
unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
MIN
LTC1196
TYP
MAX
MIN
LTC1198
TYP
MAX
UNITS
S/(N + D) Signal-to-Noise Plus Distortion
500kHz/1MHz Input Signal
47/45
47/45
dB
THD
Total Harmonic Distortion
500kHz/1MHz Input Signal
49/47
49/47
dB
Peak Harmonic or Spurious Noise
500kHz/1MHz Input Signal
55/48
55/48
dB
Intermodulation Distortion
fIN1 = 499.37kHz
fIN2 = 502.446kHz
51
51
dB
Full-Power Bandwidth
8
8
MHz
Full Linear Bandwidth [S/(N + D) > 44dB
1
1
MHz
IMD
AC CHARACTERISTICS
The l denotes the specifications which apply over the full operating temperature range,
otherwise specifications are at TA = 25°C. VCC = 5V, VREF = 5V, fCLK = fCLK(MAX) as defined in Recommended Operating Conditions,
unless otherwise noted.
SYMBOL
PARAMETER
tCONV
Conversion Time (See Figures 1, 2)
CONDITIONS
MIN
LTC1196-1
LTC1198-1
TYP
LTC1196
LTC1196
LTC1198
LTC1198
tdDO
Delay Time, CLK↑ to DOUT Data Valid
CLOAD = 20pF
tDIS
Delay Time CS↑ to DOUT Hi-Z
ten
Delay Time, CLK↓ to DOUT Enabled
thDO
l
l
MIN
600
710
l
fSMPL(MAX) Maximum Samping Frequency
MAX
LTC1196-2
LTC1198-2
TYP
1.20
1.00
0.90
0.75
MAX
UNITS
710
900
ns
ns
1.00
0.80
0.75
0.60
MHz
MHz
MHz
MHz
55
64
73
68
78
94
ns
ns
l
70
120
88
150
ns
CLOAD = 20pF
l
30
50
43
63
ns
Time Output Data Remains Valid After
CLK↑
CLOAD = 20pF
l
tf
DOUT Fall Time
CLOAD = 20pF
l
tr
DOUT Rise
CLOAD = 20pF
l
CIN
Input Capacitance
Analog Input On Channel
Analog Input Off Channel
Digital Input
l
30
45
30
55
ns
5
15
10
20
ns
5
15
10
20
ns
30
5
5
30
5
5
pF
pF
pF
119698fa
4
LTC1196/LTC1198
RECOMMENDED OPERATING CONDITIONS
The l denotes the specifications which apply over
the full operating temperature range, otherwise specifications are at TA = 25°C. VCC = 2.7V Operation.
SYMBOL
PARAMETER
fCLK
Clock Frequency
tCYC
Total Cycle Time
CONDITIONS
MIN
l
LTC1196
LTC1198
LTC1196-1
LTC1198-1
TYP
0.01
0.01
MAX
MIN
5.4
4.6
0.01
0.01
LTC1196-2
LTC1198-2
TYP
MAX
UNITS
4
3
MHz
MHz
12
16
12
16
CLK
CLK
tSMPL
Analog Input Sampling Time
2.5
2.5
CLK
thCS
Hold Time CS Low After Last CLK↑
20
40
ns
tsuCS
Setup Time CS↓ Before First CLK↑
(See Figures 1, 2)
40
78
ns
thDI
Hold Time DIN After CLK↑
LTC1198
40
78
ns
tsuDI
Setup Time DIN Stable Before CLK↑
LTC1198
40
78
ns
tWHCLK
CLK High Time
fCLK = fCLK(MAX)
40%
40%
1/fCLK
tWLCLK
CLK Low Time
fCLK = fCLK(MAX)
40%
40%
1/fCLK
tWHCS
CS High Time Between Data Transfer
Cycles
50
96
ns
tWLCS
CS Low Time During Data Transfer
11
15
11
15
CLK
CLK
LTC1196
LTC1198
CONVERTER AND MULTIPLEXER CHARACTERISTICS
The l denotes the specifications
which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VCC = 2.7V, VREF = 2.5V,
fCLK = fCLK(MAX) as defined in Recommended Operating Conditions, unless otherwise noted.
PARAMETER
CONDITIONS
MIN
LTC1196-1
LTC1198-1
TYP
MAX
MIN
LTC1196-2
LTC1198-2
TYP
MAX
UNITS
No Missing Codes Resolution
l
Offset Error
l
±1/2
±1
LSB
l
±1/2
±1
LSB
l
±1/2
±1
LSB
l
±1/2
±1
LSB
Linearity Error
(Note 3)
Full-Scale Error
Total Unadjusted Error (Note 4)
LTC1196, VREF = 2.5.000V
LTC1198, VCC = 2.700V
Analog and REF Input Range
LTC1196
Analog Input Leakage Current
(Note 5)
8
8
Bits
–0.05V to VCC + 0.05V
l
±1
V
±1
μA
DIGITAL AND DC ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply
over the full operating temperature range, otherwise specifications are at TA = 25°C. VCC = 2.7V, VREF = 2.5V, unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
VIH
High Level Input Voltage
VCC = 3.6V
l
MIN
TYP
MAX
VIL
Low Level Input Voltage
VCC = 2.7V
l
2.5
μA
–2.5
μA
1.9
UNITS
V
0.45
V
IIH
High Level Input Current
VIN = VCC
l
IIL
Low Level Input Current
VIN = 0V
l
VOH
High Level Output Voltage
VCC = 2.7V, IO = 10μA
VCC = 2.7V, IO = 360μA
l
l
VOL
Low Level Output Voltage
VCC = 2.7V, IO = 400μA
l
0.3
V
Hi-Z Output Leakage
CS = High
l
±3
μA
IOZ
2.3
2.1
2.60
2.45
V
V
119698fa
5
LTC1196/LTC1198
DIGITAL AND DC ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply
over the full operating temperature range, otherwise specifications are at TA = 25°C. VCC = 2.7V, VREF = 2.5V, unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
ISOURCE
Output Source Current
VOUT = 0V
ISINK
Output Sink Current
VOUT = VCC
IREF
Reference Current, LTC1196
ICC
Supply Current
MIN
TYP
MAX
UNITS
–10
mA
15
mA
CS = VCC
fSMPL = fSMPL(MAX)
l
l
0.001
0.25
3.0
0.5
μA
mA
CS = VCC = 3.3V, LTC1198 (Shutdown)
CS = VCC = 3.3V, LTC1196
fSMPL = fSMPL(MAX), LTC1196/LTC1198
l
l
l
0.001
1.5
2.0
3.0
4.5
6.0
μA
mA
mA
DYNAMIC ACCURACY
The l denotes the specifications which apply over the full operating temperature range,
otherwise specifications are at TA = 25°C. VCC = 2.7V, VREF = 2.5V, fCLK = fCLK(MAX) as defined in Recommended Operating Conditions,
unless otherwise noted.
MAX
MIN
LTC1198
TYP
CONDITIONS
S/(N + D) Signal-to-Noise Plus Distortion
190kHz/380kHz Input Signal
47/45
47/45
dB
THD
IMD
MIN
LTC1196
TYP
SYMBOL PARAMETER
MAX
UNITS
Total Harmonic Distortion
190kHz/380kHz Input Signal
49/47
49/47
dB
Peak Harmonic or Spurious Noise
190kHz/380kHz Input Signal
53/46
55/46
dB
Intermodulation Distortion
fIN1 = 189.37kHz
fIN2 = 192.446kHz
51
51
dB
5
5
MHz
0.5
0.5
MHz
Full-Power Bandwidth
Full Linear Bandwidth [S/(N + D) > 44dB
AC CHARACTERISTICS
The l denotes the specifications which apply over the full operating temperature range,
otherwise specifications are at TA = 25°C. VCC = 2.7V, VREF = 2.5V, fCLK = fCLK(MAX) as defined in Recommended Operating Conditions,
unless otherwise noted.
SYMBOL
PARAMETER
tCONV
Conversion Time (See Figures 1, 2)
fSMPL(MAX) Maximum Samping Frequency
tdDO
Delay Time, CLK↑ to DOUT Data Valid
tDIS
Delay Time CS↑ to DOUT Hi-Z
ten
Delay Time, CLK↓ to DOUT Enabled
CONDITIONS
MIN
LTC1196-1
LTC1198-1
TYP
CLOAD = 20pF
l
l
MIN
1.58
1.85
l
LTC1196
LTC1196
LTC1198
LTC1198
MAX
LTC1196-2
LTC1198-2
TYP
450
383
337
287
MAX
UNITS
2.13
2.84
μs
μs
333
250
250
187
kHz
kHz
kHz
kHz
100
150
180
130
200
250
ns
ns
l
110
220
120
250
ns
CLOAD = 20pF
l
80
130
100
200
ns
CLOAD = 20pF
l
l
thDO
Time Output Data Remains Valid After
CLK↑
tf
DOUT Fall Time
CLOAD = 20pF
l
10
30
15
40
ns
tr
DOUT Rise
CLOAD = 20pF
l
10
30
15
40
ns
CIN
Input Capacitance
Analog Input On Channel
Analog Input Off Channel
Digital Input
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
45
90
30
5
5
45
120
ns
30
5
5
pF
pF
pF
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
119698fa
6
LTC1196/LTC1198
ELECTRICAL CHARACTERISTICS
Note 4: Total unadjusted error includes offset, full scale, linearity,
multiplexer and hold step errors.
Note 5: Channel leakage current is measured after the channel selection.
Note 2: All voltage values are with respect to GND.
Note 3: Integral nonlinearity is defined as deviation of a code from a
straight line passing through the actual endpoints of the transfer curve.
The deviation is measured from the center of the quantization band.
TYPICAL PERFORMANCE CHARACTERISTICS
Supply Current vs Clock Rate
Supply Current vs Supply Voltage
9
14
VCC = 5V
TA = 25°C
CS = 0V
VREF = VCC
3
VCC = 2.7V
2
10
“ACTIVE” MODE
CS = 0V
8
LTC1196
LTC1198
6
4
2
1
0.000002
0
0
2
4
6
8
10 12
FREQUENCY (MHz)
14
16
SUPPLY CURRENT (mA)
6
4
LT1196 VCC = 5V
LTC1198
0
2.5
3.0
5.0
3.5 4.0 4.5
SUPPLY VOLTAGE (V)
1196/98 G01
SUPPLY CURRENT (mA)
8
7
VCC = 5V
6
5
4
3
2
VCC = 2.7V
1
0
–55 –35 –15
5 25 45 65 85 105 125
TEMPERATURE (°C)
1196/98 G04
LT1198 VCC = 5V
0.1
LT1198 VCC = 2.7V
0.01
5.5
6.0
TA = 25°C
0.001
100
1k
1.6
1.4
1M
10k
100k
SAMPLE RATE (Hz)
1196/98 G03
Offset vs Reference Voltage
MAGNITUDE OF OFFSET (LSB = 1 s VREF)
256
CS = 0V
9
LT1196 VCC = 2.7V
1196/98 G02
Supply Current vs Temperature
10
1
“SHUTDOWN” MODE
CS = VCC
Offset vs Supply Voltage
TA = 25°C
VCC = 5V
fCLK = 12MHz
1.2
1.0
0.8
0.6
0.4
0.2
0.5
0.4
MAGNITUDE OF OFFSET (LSB)
7
5
10
TA = 25°C
12
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
8
Supply Current vs Sample Rate
0.3
TA = 25°C
VREF = VCC
fCLK = 3MHz
0.2
0.1
0
–0.1
–0.2
–0.3
–0.4
0
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
REFERENCE VOLTAGE (V)
1196/98 G05
–0.5
2.5
3.0
3.5 4.0 4.5
5.0
SUPPLY VOLTAGE (V)
5.5
6.0
1196/98 G06
119698fa
7
LTC1196/LTC1198
TYPICAL PERFORMANCE CHARACTERISTICS
Linearity Error vs
Reference Voltage
TA = 25°C
VCC = 5V
fCLK = 12MHz
0.9
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
–0.1
–0.2
0.2
–0.3
0.1
–0.4
0
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
REFERENCE VOLTAGE (V)
2.5
3.0
3.5 4.0 4.5
5.0
SUPPLY VOLTAGE (V)
0.2
0.1
0
–0.1
–0.2
–0.3
–0.4
5.5
17
–0.3
0
1196/98 G09
TA = 25°C
VCC = VREF = 5V
16
11
9
7
14
12
VIN
–IN
8
RSOURCE–
6
4
2
0
3.0
5.0
3.5 4.0 4.5
SUPPLY VOLTAGE (V)
5.5
1
6.0
60
50
40
30
20
10
5 25 45 65 85 105 125
TEMPERATURE (°C)
1196/98 G13
1k
10
10k
100
SOURCE RESISTANCE (Ω)
0.30
100k
1196/98 G12
Sample-and-Hold Acquisition
Time vs Source Resistance
10000
TA = 25°C
VCC = VREF = 5V
TA = 25°C
VREF = VCC
S&H ACQUISITION TIME (ns)
0.35
70
+IN
10
ADC Noise vs Referenced and
Supply Voltage
80
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
REFERENCE VOLTAGE (V)
1196/98 G11
PEAK-TO-PEAK ADC NOISE (LSB)
MINIMUM CLOCK FREQUENCY (kHz)
–0.2
18
13
5
2.5
6.0
VCC = 5V
VREF = 5V
0
–55 –35 –15
0
–0.1
Maximum Clock Frequency vs
Source Resistance
15
Minimum Clock Rate for
0.1LSB* Error
90
0.1
–0.5
6.0
TA = 25°C
VREF = VCC
1196/98 G10
100
5.5
CLOCK FREQUENCY (MHz)
MAXIMUM CLOCK FREQUENCY (MHz)
MAGNITUDE OF GAIN ERROR (LSB)
19
TA = 25°C
0.4 fCLK = 3MHz
VREF = VCC
0.3
3.5 4.0 4.5
5.0
SUPPLY VOLTAGE (V)
0.2
Maximum Clock Frequency vs
Supply Voltage
0.5
3.0
0.3
1196/98 G08
Gain vs Supply Voltage
2.5
TA = 25°C
VCC = 5V
fCLK = 12MHz
0.4
–0.4
–0.5
1196/98 G07
–0.5
Supply Current vs Sample Rate
0.5
TA = 25°C
0.4 VREF = VCC
f
= 3MHz
0.3 CLK
LINEARITY ERROR (LSB)
0.8
LINEARITY ERROR (LSB)
Linearity Error vs Supply Voltage
0.5
MAGNITUDE OF GAIN ERROR (LSB)
1.0
0.25
0.20
RSOURCE+
VIN
1000
0.15
0.10
+IN
–IN
0.05
0
2.5
100
3.0
5.0
3.5 4.0 4.5
SUPPLY VOLTAGE (V)
5.5
6.0
1196/98 G14
1
100
10
1k
SOURCE RESISTANCE (Ω)
10k
1196/98 G15
*AS THE FREQUENCY IS DECREASED FROM 12MHz, MINIMUM CLOCK FREQUENCY (ΔERROR ≤ 0.1LSB) REPRESENTS THE
FREQUENCY AT WHICH A 0.1LSB SHIFT IN ANY CODE TRANSITION FROM ITS 12MHz VALUE IS FIRST DETECTED.
119698fa
8
LTC1196/LTC1198
TYPICAL PERFORMANCE CHARACTERISTICS
Digital Input Logic Threshold vs
Supply Voltage
1.9
DOUT Delay Time vs Supply
Voltage
TA = 25°C
1.5
1.3
1.1
0.9
100
80
60
40
20
0.7
0.5
2.5
5.0
3.5 4.0 4.5
SUPPLY VOLTAGE (V)
3.0
5.5
5.0
3.5 4.0 4.5
SUPPLY VOLTAGE (V)
3.0
0.5
INTEGRAL NONLINEARITY ERROR (LSB)
LEAKAGE CURRENT (nA)
100
10
ON CHANNEL
1
OFF CHANNEL
0.1
0
64
32
64
96 128 160 192 224 256
CODE
96 128 160 192 224 256
CODE
1196/98 G22
0.5
VCC = 5V
VREF = 5V
fCLK = 12MHz
0
–0.5
0
32
64
96 128 160 192 224 256
CODE
1196/98 G21
Differential Nonlinearity vs
Code at 2.7V
0.5
Effective Bits and S/(N + D) vs
Input Frequency
8
VCC = 2.7V
VREF = 2.5V
fCLK = 3MHz
EFFECTIVE NUMBER OF BITS (ENOBs)
DIFFERENTIAL NONLINEARITY ERROR (LSB)
INTEGRAL NONLINEARITY ERROR (LSB)
Differential Nonlinearity vs
Code at 5V
0
–0.5
0
32
64
96 128 160 192 224 256
CODE
1196/98 G23
50
VREF = VCC = 2.7V
fSMPL = 383kHz (LTC1196)
fSMPL = 287kHz (LTC1198)
7
6
44
VREF = VCC = 5V
fSMPL = 1MHz (LTC1196)
fSMPL = 750kHz (LTC1198)
5
S/(N + D) (dB)
32
1196/98 G18
1196/98 G20
Integral Nonlinearity vs
Code at 2.7V
0
40
0
–60 –40 –20 0 20 40 60 80 100 120 140
TEMPERATURE (°C)
0
1196/98 G19
0
60
6.0
VCC = 5V
VREF = 5V
fCLK = 12MHz
–0.5
0.01
–60 –40 –20 0 20 40 60 80 100 120 140
TEMPERATURE (°C)
VCC = 2.7V
VREF = 2.5V
fCLK = 3MHz
VCC = 5V
80
Integral Nonlinearity vs
Code at 5V
VCC = 5V
VREF = 5V
–0.5
5.5
DIFFERENTIAL NONLINEARITY ERROR (LSB)
Input Channel Leakage Current
vs Temperature
0.5
100
1196/98 G17
1196/98 G16
1000
VCC = 2.7V
120
20
0
2.5
6.0
VREF = VCC
140
DOUT DELAY TIME, tdDO (ns)
DOUT DELAY TIME, tdDO (ns)
LOGIC THRESHOLD (V)
TA = 25°C
VREF = VCC
120
1.7
DOUT Delay Time vs Temperature
160
140
4
3
2
1
TA = 25°C
0
1k
10k
100k
INPUT FREQUENCY (Hz)
1M
1196/98 G24
119698fa
9
LTC1196/LTC1198
TYPICAL PERFORMANCE CHARACTERISTICS
4096 Point FFT Plot at 5V
–20
–40
–50
–60
–70
–20
–30
–40
–50
–60
–70
–30
–40
–50
–60
–70
–80
–90
–90
–90
300
200
FREQUENCY (kHz)
400
–100
500
0
50
150
100
FREQUENCY (kHz)
–20
–30
–40
–50
–60
–60
–70
–70
10k
100k
RIPPLE FREQUENCY (Hz)
1k
1M
10k
100k
RIPPLE FREQUENCY (Hz)
Intermodulation Distortion at 2.7V
–40
–50
–60
–70
–20
–40
–50
–60
–70
–80
–90
–90
0
50
150
100
FREQUENCY (kHz)
200
250
1196/98 G31
fIN = 200kHz
fIN = 500kHz
40
35
30
VCC = 5V
25
1.25 1.75 2.25 2.75 3.25 3.75 4.25 4.75 5.25
REFERENCE VOLTAGE (V)
1196/98 G30
S/(N + D) vs Input Level
–30
–80
–100
1M
VCC = 5V
f1 = 200kHz
f2 = 210kHz
fSMPL = 750kHz
–10
MAGNITUDE (dB)
–30
500
fIN = 100kHz
Intermodulation Distortion at 5V
0
VCC = 2.7V
f1 = 100kHz
f2 = 110kHz
fSMPL = 420kHz
–20
45
1196/98 G29
1196/98 G28
–10
400
-
–50
300
200
FREQUENCY (kHz)
50
SIGNAL TO NOISE PLUS DISTORTION (dB)
–20
FEEDTHROUGH (dB)
TA = 25°C
= 10mV)
V (V
–10 f CC = RIPPLE
CLK 5MHz
–40
100
S/(N + D) vs Reference Voltage
and Input Frequency
0
TA = 25°C
= 20mV)
V (V
–10 f CC = RIPPLE
CLK 12MHz
–30
0
1196/98 G27
Power Supply Feedthrough vs
Ripple Frequency
0
0
–100
1196/98 G26
Power Supply Feedthrough vs
Ripple Frequency
1k
200
–100
0
100
300
200
FREQUENCY (kHz)
400
1196/98 G32
50
SIGNAL TO NOISE-PLUS-DISTORTION (dB)
100
1196/98 G25
FEEDTHROUGH (dB)
–20
–80
0
VCC = 5V
fIN = 455kHz WITH 20kHz AM
fSMPL = 1MHz
–10
–80
–100
MAGNITUDE (dB)
0
VCC = 2.7V
fIN = 29kHz
fSMPL = 340kHz
–10
MAGNITUDE (dB)
–30
MAGNITUDE (dB)
0
VCC = 5V
fIN = 29kHz
fSMPL = 882kHz
MAGNITUDE (dB)
0
–10
FFT Output of 455kHz AM Signal
Digitized at 1Msps
4096 Point FFT Plot at 2.7V
40
VREF = VCC = 5V
fIN = 500kHz
fSMPL = 1MHz
30
20
10
0
–40 –35 –30 –25 –20 –15 –10
INPUT LEVEL (dB)
–5
0
1196/98 G33
119698fa
10
LTC1196/LTC1198
TYPICAL PERFORMANCE CHARACTERISTICS
Output Amplitude vs
Input Frequency
Spurious-Free Dynamic Range
vs Frequency
70
SPURIOUS-FREE DYNAMIC RANGE (dB)
PEAK-TO-PEAK OUTPUT (%)
100
80
VREF = VCC = 5V
60
VREF = VCC = 2.7V
40
20
0
50
100k
10k
1M
INPUT FREQUENCY (Hz)
VCC = 3V
fCLK = 5MHz
40
30
20
10
0
1k
VCC = 5V
fCLK = 12MHz
60
10M
TA = 25°C
1k
10k
100k
1M
10M
FREQUENCY (Hz)
1196/98 G34
1196/98 G35
PIN FUNCTIONS
LTC1196
LTC1198
CS (Pin 1): Chip Select Input. A logic low on this input
enables the LTC1196. A logic high on this input disables
the LTC1196.
CS/SHUTDOWN (Pin 1): Chip Select Input. A logic low
on this input enables the LTC1198. A logic high on this
input disables the LTC1198 and disconnects the power
to THE LTC1198.
IN+ (Pin 2): Analog Input. This input must be free of noise
with respect to GND.
IN– (Pin 3): Analog Input. This input must be free of noise
with respect to GND.
GND (Pin 4): Analog Ground. GND should be tied directly
to an analog ground plane.
VREF (Pin 5): Reference Input. The reference input defines
the span of the A/D converter and must be kept free of
noise with respect to GND.
CHO (Pin 2): Analog Input. This input must be free of
noise with respect to GND.
CH1 (Pin 3): Analog Input. This input must be free of noise
with respect to GND.
GND (Pin 4): Analog Ground. GND should be tied directly
to an analog ground plane.
DIN (Pin 5): Digital Data Input. The multiplexer address is
shifted into this input.
DOUT (Pin 6): Digital Data Output. The A/D conversion
result is shifted out of this output.
DOUT (Pin 6): Digital Data Output. The A/D conversion
result is shifted out of this output.
CLK (Pin 7): Shift Clock. This clock synchronizes the serial data transfer.
CLK (Pin 7): Shift Clock. This clock synchronizes the serial data transfer.
VCC (Pin 8): Power Supply Voltage. This pin provides power
to the A/D converter. It must be kept free of noise and ripple
by bypassing directly to the analog ground plane.
VCC (VREF)(Pin 8): Power Supply and Reference Voltage.
This pin provides power and defines the span of the A/D
converter. It must be kept free of noise and ripple by bypassing directly to the analog ground plane.
119698fa
11
LTC1196/LTC1198
BLOCK DIAGRAM
CS
(CS/SHUTDOWN) CLK
VCC (VCC/VREF)
BIAS AND
SHUTDOWN CIRCUIT
IN+ (CH0)
CSMPL
SERIAL PORT
DOUT
–
IN– (CH1)
+
SAR
HIGH SPEED
COMPARATOR
CAPACITIVE DAC
1196/98 BD
PIN NAMES IN PARENTHESES
REFER TO THE LTC1198
GND
VREF (DIN)
TEST CIRCUITS
On and Off Channel Leakage Current
Load Circuit for tdDO, tr and tf
5V
1.4V
ION
A
3k
ON CHANNEL
DOUT
IOFF
TEST POINT
100pF
A
•
•
•
•
POLARITY
OFF
CHANNEL
1196/98 TC02
1196/98 TC01
Voltage Waveform for DOUT Rise and Fall Times, tr , tf
Voltage Waveform for DOUT Delay Time, tdDO , thDO
VOH
DOUT
CLK
VOL
tr
VIH
tdDO
thDO
tf
1196/98 TC04
VOH
DOUT
VOL
1196/98 TC03
119698fa
12
LTC1196/LTC1198
TEST CIRCUITS
Load Circuit for tdis and ten
Voltage Waveforms for tdis
TEST POINT
CS
VIH
VCC tdis WAVEFORM 2, ten
3k
DOUT
DOUT
WAVEFORM 1
(SEE NOTE 1)
tdis WAVEFORM 1
20pF
90%
tdis
1196/98 TC05
DOUT
WAVEFORM 2
(SEE NOTE 2)
10%
NOTE 1: WAVEFORM 1 IS FOR AN OUTPUT WITH INTERNAL CONDITIONS SUCH
THAT THE OUTPUT IS HIGH UNLESS DISABLED BY THE OUTPUT CONTROL.
NOTE 2: WAVEFORM 2 IS FOR AN OUTPUT WITH INTERNAL CONDITIONS SUCH
THAT THE OUTPUT IS LOW UNLESS DISABLED BY THE OUTPUT CONTROL.
1196/98 TC06
Voltage Waveforms for ten
LTC1196
CS
CLK
2
1
3
4
B7
DOUT
VOL
1196/98 TC07
ten
Voltage Waveforms for ten
LTC1198
CS
DIN
CLK
START
1
2
3
5
4
6
7
B7
DOUT
VOL
ten
1196/98 TC08
119698fa
13
LTC1196/LTC1198
APPLICATIONS INFORMATION
OVERVIEW
with respect to ground or the difference between the two.
It also automatically powers down when not performing
conversion, drawing only leakage current.
The LTC1196/LTC1198 are 600ns sampling 8-bit A/D converters packaged in tiny 8-pin SO packages and operating
on 3V to 6V supplies. The ADCs draw only 10mW from a
3V supply or 50mW from a 5V supply.
SERIAL INTERFACE
The LTC1196/LTC1198 will interface via three or four wires
to ASICs, PLDs, microprocessors, DSPs, or shift registers
(see Operating Sequence in Figures 1 and 2). To run at their
fastest conversion rates (600ns), they must be clocked at
14.4MHz. HC logic families and any high speed ASIC or
PLD will easily interface to the ADCs at that speed (see
Data Transfer and Typical Application sections). Full speed
operation from a 3V supply can still be achieved with 3V
ASICs, PLDs or HC logic circuits.
Both the LTC1196 and the LTC1198 contain an 8-bit,
switched-capacitor ADC, a sample-and-hold, and a serial
port (see Block Diagram). The on-chip sample-and-holds
have full-accuracy input bandwidths of 1MHz. Although
they share the same basic design, the LTC1196 and LTC1198
differ in some respects. The LTC1196 has a differential input
and has an external reference input pin. It can measure
signals floating on a DC common mode voltage and can
operate with reduced spans below 1V. The LTC1198 has a
2-channel input multiplexer and can convert either channel
tCYC (12 CLKs)
CS
tsuCS
tdDO
DOUT
B0
B7
NULL BITS
Hi-Z
B6
B5
B4
B3
B2
B1
B0*
tCYC (8.5 CLKs)
tSMPL
NULL
BITS
Hi-Z
tSMPL
*AFTER COMPLETING THE DATA TRANSFER, IF FURTHER CLOCKS ARE APPLIED WITH CS LOW, THE ADC WILL OUTPUT ZEROS INDEFINITELY
1196/98 F01
Figure 1. LTC1196 Operating Sequence
tCYC (16 CLKs)
CS
POWER
DOWN
tsuCS
CLK
ODD/
SIGN
START
DUMMY
DIN
DON’T CARE
SGL/
DIFF
DOUT
DUMMY
tdDO
NULL BITS
HI-Z
tSMPL (2.5 CLKs)
B7
B6
B5
B4
B3
B2
B1
B0*
Hi-Z
tCONV (8.5 CLKs)
*AFTER COMPLETING THE DATA TRANSFER, IF FURTHER CLOCKS ARE APPLIED WITH CS LOW, THE ADC WILL OUTPUT ZEROS INDEFINITELY
1196/98 F02
Figure 2. LTC1198 Operating Sequence Example: Differential Inputs (CH1, CH0)
119698fa
14
LTC1196/LTC1198
APPLICATIONS INFORMATION
Connection to a microprocessor or a DSP serial port is
quite simple (see Data Transfer section). It requires no
additional hardware, but the speed will be limited by the
clock rate of the microprocessor or the DSP which limits
the conversion time of the LTC1196/LTC1198.
Data Transfer
Data transfer differs slightly between the LTC1196 and the
LTC1198. The LTC1196 interfaces over 3 lines: CS, CLK
and DOUT . A falling CS initiates data transfer as shown
in the LTC1196 Operating Sequence. After CS falls, the
first CLK pulse enables DOUT . After two null bits, the A/D
conversion result is output on the DOUT line. Bringing CS
high resets the LTC1196 for the next data exchange.
the end of the data exchange CS should be brought high.
This resets the LTC1198 in preparation for the next data
exchange.
Input Data Word
The LTC1196 requires no DIN word. It is permanently configured to have a single differential input. The conversion
result is output on the DOUT line in an MSB-first sequence,
followed by zeros indefinitely if clocks are continuously
applied with CS low.
The LTC1198 clocks data into the DIN input on the rising edge of the clock. The input data word is defined
as follows:
START
The LTC1198 can transfer data with 3 or 4 wires. The additional input, DIN, is used to select the 2-channel MUX
configuration.
The data transfer between the LTC1198 and the digital
systems can be broken into two sections: Input Data Word
and A/D Conversion Result. First, each bit of the input data
word is captured on the rising CLK edge by the LTC1198.
Second, each bit of the A/D conversion result on the DOUT
line is updated on the rising CLK edge by the LTC1198. This
bit should be captured on the next rising CLK edge by the
digital systems (see A/D Conversion Result section).
Data transfer is initiated by a falling chip select (CS) signal
as shown in the LTC1198 Operating Sequence. After CS
falls the LTC1198 looks for a start bit. After the start bit
is received, the 4-bit input word is shifted into the DIN
input. The first two bits of the input word configure the
LTC1198. The last two bits of the input word allow the
ADC to acquire the input voltage by 2.5 clocks before the
conversion starts. After the conversion starts, two null bits
and the conversion result are output on the DOUT line. At
SGL/
DIFF
ODD/
SIGN
MUX
ADDRESS
DUMMY DUMMY
DUMMY
BITS
119698 AI02
Start Bit
The first “logical one” clocked into the DIN input after CS
goes low is the start bit. The start bit initiates the data
transfer. The LTC1198 will ignore all leading zeros which
precede this logical one. After the start bit is received,
the remaining bits of the input word will be clocked in.
Further inputs on the DIN pin are then ignored until the
next CS cycle.
Multiplexer (MUX) Address
The 2 bits of the input word following the START bit assign
the MUX configuration for the requested conversion. For
a given channel selection, the converter will measure the
voltage between the two channels indicated by the “+”
and “–” signs in the selected row of the following table.
In single-ended mode, all input channels are measured
with respect to GND.
LTC1198 Channel Selection
CS
DIN1
DIN2
DOUT1
DOUT2
SINGLE-ENDED
MUX MODE
SHIFT MUX
ADDRESS IN
DIFFERENTIAL
MUX MODE
2 NULL BITS
SHIFT A/D CONVERSION
RESULT OUT
MUX ADDRESS
SGL/DIFF ODD/SIGN
1
0
1
1
0
0
0
1
CHANNEL #
0
1
+
+
–
+
+
–
GND
–
–
1196/98 AI03
1196/98 AI01
119698fa
15
LTC1196/LTC1198
APPLICATIONS INFORMATION
Unipolar Output Code
Dummy Bits
The last 2 bits of the input word following the MUX Address are dummy bits. Either bit can be a “logical one” or
a “logical zero.” These 2 bits allow the ADC 2.5 clocks to
acquire the input signal after the channel selection.
A/D Conversion Result
INPUT VOLTAGE
INPUT VOLTAGE
(VREF = 5.000V)
11111111
11111110
•
•
•
00000001
00000000
VREF – 1LSB
VREF – 2LSB
•
•
•
1LSB
0V
4.9805V
4.9609V
•
•
•
0.0195V
0V
1196/98 AI05
Both the LTC1196 and the LTC1198 have the A/D conversion result appear on the DOUT line after two null bits (see
Operating Sequence in Figures 1 and 2). Data on the DOUT
line is updated on the rising edge of the CLK line. The DOUT
data should also be captured on the rising CLK edge by the
digital systems. Data on the DOUT line remains valid for a
minimum time of thDO (30ns at 5V) to allow the capture
to occur (see Figure 3).
VIH
CLK
OUTPUT CODE
tdDO
thDO
VOH
DOUT
VOL
Operation with DIN and DOUT Tied Together
The LTC1198 can be operated with DIN and DOUT tied
together. This eliminates one of the lines required to communicate to the digital systems. Data is transmitted in both
directions on a single wire. The pin of the digital systems
connected to this data line should be configurable as either
an input or an output. The LTC1198 will take control of the
data line and drive it low on the 5th falling CLK edge after
the start bit is received (see Figure 4). Therefore the port
line of the digital systems must be switched to an input
before this happens to avoid a conflict.
REDUCING POWER CONSUMPTION
1196/98 TC03
Figure 3. Voltage Waveform for DOUT Delay Time, tdDO and thDO
Unipolar Transfer Curve
The LTC1196/LTC1198 are permanently configured for
unipolar only. The input span and code assignment for this
conversion type are shown in the following figures.
Unipolar Transfer Curve
11111111
The LTC1196/LTC1198 can sample at up to a 1MHz rate,
drawing only 50mW from a 5V supply. Power consumption
can be reduced in two ways. Using a 3V supply lowers the
power consumption on both devices by a factor of five,
to 10mW. The LTC1198 can reduce power even further
because it shuts down whenever it is not converting.
Figure 5 shows the supply current versus sample rate for
the LTC1196 and LTC1198 on 3V and 5V. To achieve such
a low power consumption, especially for the LTC1198,
several things must be taken into consideration.
Shutdown (LTC1198)
11111110
•
•
•
00000001
00000000
VIN
VREF
VREF – 1LSB
VREF – 2LSB
1LSB
0V
Figure 2 shows the operating sequence of the LTC1198.
The converter draws power when the CS pin is low and
powers itself down when that pin is high. For lowest power
consumption in shutdown, the CS pin should be driven
with CMOS levels (0V to VCC) so that the CS input buffer
of the converter will not draw current.
1196/98 AI04
119698fa
16
LTC1196/LTC1198
APPLICATIONS INFORMATION
DUMMY BITS LATCHED
BY LTC1198
CS
1
2
3
4
ODD/SIGN
DUMMY
5
CLK
DATA (DIN/DOUT)
START
SGL/DIFF
THE DIGITAL SYSTEM CONTROLS DATA LINE
AND SENDS MUX ADDRESS TO LTC1198
LTC1198 CONTROLS DATA LINE AND SENDS
A/D RESULT BACK TO THE DIGITAL SYSTEM
THE DIGITAL SYSTEM MUST RELEASE
DATA LINE AFTER 5TH RISING CLK
AND BEFORE THE 5TH FALLING CLK
LTC1198 TAKES CONTROL OF
DATA LINE ON 5TH FALLING CLK
1196/98 F04
Figure 4. LTC1198 Operation with DIN and DOUT Tied Together
SUPPLY CURRENT (mA)
10
1
0.1
In systems that have significant time between conversions, lowest power drain will occur with the minimum
CS low time. Bringing CS low, transfering data as quickly
as possible, then bringing it back high will result in the
lowest current drain. This minimizes the amount of time
the device draws power.
LT1196 VCC = 2.87V
LT1198 VCC = 5V
LT1198 VCC = 2.87V
0.01
0.001
100
Minimize CS Low Time (LTC1198)
LT1198 VCC = 5V
OPERATING ON OTHER THAN 5V SUPPLIES
1k
10k
100k
SAMPLE RATE (Hz)
1M
1196/98 F05
Figure 5. Supply Current vs Sample Rate for LTC1196/LTC1198
Operating on 5V and 2.7V Supplies
When the CS pin is high (= supply voltage), the LTC1198
is in shutdown mode and draws only leakage current.
The status of the DIN and CLK input has no effect on the
supply current during this time. There is no need to stop
DIN and CLK with CS = high; they can continue to run
without drawing current.
The LTC1196/LTC1198 operate from single 2.7V to 6V
supplies. To operate the LTC1196/LTC1198 on other than
5V supplies, a few things must be kept in mind.
Input Logic Levels
The input logic levels of CS, CLK and DIN are made to meet
TTL on 5V supply. When the supply voltage varies, the input
logic levels also change (see typical curve of Digital Input
Logic Threshold vs Supply Voltage). For these two ADCs
to sample and convert correctly, the digital inputs have
to be in the logical low and high relative to the operating
supply voltage. If achieving micropower consumption is
desirable on the LTC1198, the digital inputs must go railto-rail between supply voltage and ground (see Reducing
Power Consumption section).
119698fa
17
LTC1196/LTC1198
APPLICATIONS INFORMATION
Clock Frequency
The maximum recommended clock frequency is 14.4MHz
at 25°C for the LTC1196/LTC1198 running off a 5V supply.
With the supply voltage changing, the maximum clock frequency for the devices also changes (see the typical curve
of Maximum Clock Rate vs Supply Voltage). If the supply
is reduced, the clock rate must be reduced also. At 3V the
devices are specified with a 5.4MHz clock at 25°C.
Mixed Supplies
It is possible to have a digital system running off a 5V supply
and communicate with the LTC1196/LTC1198 operating on
a 3V supply. Achieving this reduces the outputs of DOUT
from the ADCs to toggle the equivalent input of the digital
system. The CS, CLK and DIN inputs of the ADCs will take
5V signals from the digital system without causing any
problem (see typical curve of Digital Input Logic Threshold
vs Supply Voltage). With the LTC1196 operating on a 3V
supply, the output of DOUT only goes between 0V and 3V.
This signal easily meets TTL levels (see Figure 6).
3V
4.7μF
MPU
(e.g., 8051)
CS
DIFFERENTIAL INPUTS
COMMON MODE RANGE
0V TO 3V
VCC
P1.4
CLK
P1.3
–IN
DOUT
P1.2
GND
VREF
+IN
LTC1196
supply is clean, the LTC1196/LTC1198 can also operate
with smaller 0.1μF surface mount or ceramic bypass capacitors. All analog inputs should be referenced directly to
the single-point ground. Digital inputs and outputs should
be shielded from and/or routed away from the reference
and analog circuitry.
SAMPLE-AND-HOLD
Both the LTC1196 and the LTC1198 provide a built-in
sample-and-hold (S&H) function to acquire the input
signal. The S&H acquires the input signal from “+” input
during tSMPL as shown in Figures 1 and 2. The S&H of the
LTC1198 can sample input signals in either single-ended
or differential mode (see Figure 7).
Single-Ended Inputs
The sample-and-hold of the LTC1198 allows conversion
of rapidly varying signals. The input voltage is sampled
during the tSMPL time as shown in Figure 7. The sampling
interval begins as the bit preceding the first DUMMY bit is
shifted in and continues until the falling CLK edge after the
second DUMMY bit is received. On this falling edge, the
S&H goes into hold mode and the conversion begins.
5V
Differential Inputs
3V
1196/98 F06
Figure 6. Interfacing a 3V Powered LTC1196 to a 5V System
BOARD LAYOUT CONSIDERATIONS
Grounding and Bypassing
The LTC1196/LTC1198 are easy to use if some care is
taken. They should be used with an analog ground plane
and single-point grounding techniques. The GND pin
should be tied directly to the ground plane.
The VCC pin should be bypassed to the ground plane with a
1μF tantalum with leads as short as possible. If the power
With differential inputs, the ADC no longer converts just a
single voltage but rather the difference between two voltages. In this case, the voltage on the selected “+” input
is still sampled and held and therefore may be rapidly
time varying just as in single-ended mode. However, the
voltage on the selected “–” input must remain constant
and be free of noise and ripple throughout the conversion
time. Otherwise, the differencing operation may not be
performed accurately. The conversion time is 8.5 CLK
cycles. Therefore, a change in the “–” input voltage during
this interval can cause conversion errors. For a sinusoidal
voltage on the “–” input, this error would be:
VERROR(MAX) = VPEAK • 2 • π • f(“–”) • 8.5/fCLK
where f(“–”) is the frequency of the “–” input voltage, VPEAK
is its peak amplitude and fCLK is the frequency of the CLK.
119698fa
18
LTC1196/LTC1198
APPLICATIONS INFORMATION
S A M P LE
H O LD
“+” INPUT MUST
SETTLE DURING
THIS TIME
CS
tSMPL
tCONV
CLK
DIN
START
SGL/DIFF
ODD/SIGN
DUMMY
DUMMY
DON’T CARE
B7
DOUT
1ST BIT TEST “–” INPUT MUST
SETTLE DURING THIS TIME
“+” INPUT
“–” INPUT
1196/98 F07
Figure 7. LTC1198 “+” and “–” Input Settling Windows
VERROR is proportional to f(“–”) and inversely proportional
to fCLK. For a 60Hz signal on the “–” input to generate a
1/4LSB error (5mV) with the converter running at CLK =
12MHz, its peak value would have to be 18.7V.
ANALOG INPUTS
Because of the capacitive redistribution A/D conversion
techniques used, the analog inputs of the LTC1196/LTC1198
have one capacitive switching input current spike per
conversion. These current spikes settle quickly and do
not cause a problem. However, if source resistances larger
than 100Ω are used or if slow settling op amps drive the
inputs, care must be taken to insure that the transients
caused by the current spikes settle completely before the
conversion begins.
“+” Input Settling
The input capacitor of the LTC1196 is switched onto “+”
input at the end of the conversion and samples the input
signal until the conversion begins (see Figure 1). The input
capacitor of the LTC1198 is switched onto “+” input during
the sample phase (tSMPL, see Figure 7). The sample phase
is 2.5 CLK cycles before conversion starts. The voltage on
the “+” input must settle completely within tSMPL for the
LTC1196/LTC1198. Minimizing RSOURCE+ will improve the
input settling time. If a large “+” input source resistance
must be used, the sample time can be increased by allowing more time between conversions for the LTC1196 or by
using a slower CLK frequency for the LTC1198.
119698fa
19
LTC1196/LTC1198
APPLICATIONS INFORMATION
“–” Input Settling
REFERENCE INPUT
At the end of the tSMPL, the input capacitor switches to the
“–” input and conversion starts (see Figures 1 and 7). During
the conversion, the “+” input voltage is effectively “held”
by the sample-and-hold and will not affect the conversion
result. However, it is critical that the “–” input voltage settle
completely during the first CLK cycle of the conversion time
and be free of noise. Minimizing RSOURCE– will improve
settling time. If a large “–” input source resistance must
be used, the time allowed for settling can be extended by
using a slower CLK frequency.
The voltage on the reference input of the LTC1196 defines
the voltage span of the A/D converter. The reference input
has transient capacitive switching currents which are due to
the switched-capacitor conversion technique (see Figure 9).
During each bit test of the conversion (every CLK cycle), a
capacitive current spike will be generated on the reference
pin by the ADC. These high frequency current spikes will
settle quickly and do not cause a problem if the reference
input is bypassed with at least a 0.1μF capacitor.
Input Op Amps
When driving the analog inputs with an op amp it is important that the op amp settle within the allowed time (see
Figures 1 and 7). Again, the “+” and “–” input sampling
times can be extended as described above to accommodate
slower op amps.
The reference input can be driven with standard voltage references. Bypassing the reference with a 0.1μF
capacitor is recommended to keep the high frequency
impedance low as described above. Some references
require a small resistor in series with the bypass capacitor for frequency stability. See the individual reference
data sheet for details.
REF+
5
To achieve the full sampling rate, the analog input should
be driven with a low impedance source (<100Ω) or a
high speed op amp (e.g., the LT1223, LT1191 or LT1226).
Higher impedance sources or slower op amps can easily
be accommodated by allowing more time for the analog
input to settle as described above.
Source Resistance
VIN
VIN–
RSOURCE+
“+”
INPUT
ltSMPL
RSOURCE–
“–”
INPUT
GND
4
RON
5pF TO
30pF
1196/98 F09
Figure 9. Reference Input Equivalent Circuit
Reduced Reference Operation
The analog inputs of the LTC1196/LTC1198 look like a 25pF
capacitor (CIN) in series with a 120Ω resistor (RON) as
shown in Figure 8. CIN gets switched between the selected
“+” and “–” inputs once during each conversion cycle.
Large external source resistors will slow the settling of the
inputs. It is important that the overall RC time constants
be short enough to allow the analog inputs to completely
settle within tSMPL.
+
EVERY CLK CYCLE
ROUT
VREF
LTC1196
RON
120Ω
LTC1196
LTC1198
tSMPLn
CIN
25pF
1196/98 F08
Figure 8. Analog Input Equivalent Circuit
The minimum reference voltage of the LTC1198 is limited
to 2.7V because the VCC supply and reference are internally
tied together. However, the LTC1196 can operate with
reference voltages below 1V.
The effective resolution of the LTC1196 can be increased
by reducing the input span of the converter. The LTC1196
exhibits good linearity and gain over a wide range of reference voltages (see typical curves of Linearity and FullScale Error vs Reference Voltage). However, care must be
taken when operating at low values of VREF because of the
reduced LSB step size and the resulting higher accuracy
requirement placed on the converter. The following factors
must be considered when operating at low VREF values.
1. Offset
2. Noise
119698fa
20
LTC1196/LTC1198
APPLICATIONS INFORMATION
Offset with Reduced VREF
DYNAMIC PERFORMANCE
The offset of the LTC1196 has a larger effect on the output
code when the ADC is operated with reduced reference
voltage. The offset (which is typically a fixed voltage)
becomes a larger fraction of an LSB as the size of the
LSB is reduced. The typical curve of Unadjusted Offset
Error vs Reference Voltage shows how offset in LSBs is
related to reference voltage for a typical value of VOS. For
example, a VOS of 2mV which is 0.1LSB with a 5V reference becomes 0.5LSB with a 1V reference and 2.5LSB
with a 0.2V reference. If this offset is unacceptable, it
can be corrected digitally by the receiving system or by
offsetting the “–” input of the LTC1196.
The LTC1196/LTC1198 have exceptionally high speed
sampling capability. Fast Fourier Transform (FFT) test
techniques are used to characterize the ADC’s frequency
response, distortion and noise at the rated throughput. By
applying a low distortion sine wave and analyzing the digital
output using a FFT algorithm, the ADC’s spectral content
can be examined for frequencies outside the fundamental.
Figure 10 shows a typical LTC1196 FFT plot.
The total input referred noise of the LTC1196 can be
reduced to approximately 2mVP-P using a ground plane,
good bypassing, good layout techniques and minimizing
noise on the reference inputs. This noise is insignificant
with a 5V reference but will become a larger fraction of
an LSB as the size of the LSB is reduced.
For operation with a 5V reference, the 2mV noise is only
0.1LSB peak-to-peak. In this case, the LTC1196 noise
will contribute virtually no uncertainty to the output code.
However, for reduced references, the noise may become
a significant fraction of an LSB and cause undesirable jitter in the output code. For example, with a 1V reference,
this same 2mV noise is 0.5LSB peak-to-peak. This will
reduce the range of input voltages over which a stable
output code can be achieved by 1LSB. If the reference is
further reduced to 200mV, the 2mV noise becomes equal
to 2.5LSB and a stable code is difficult to achieve. In this
case averaging readings is necessary.
This noise data was taken in a very clean setup. Any setup
induced noise (noise or ripple on VCC, VREF or VIN) will
add to the internal noise. The lower the reference voltage
to be used, the more critical it becomes to have a clean,
noise-free setup.
VCC = 5V
fIN = 29kHz
fSMPL = 882kHz
–10
–20
MAGNITUDE (dB)
Noise with Reduced VREF
0
–30
–40
–50
–60
–70
–80
–90
–100
0
100
300
200
FREQUENCY (kHz)
400
500
1196/98 G25
Figure 10. LTC1196 Non-Averaged, 4096 Point FFT Plot
Signal-to-Noise Ratio
The Signal-to-Noise plus Distortion Ratio [S/(N + D)] is
the ratio between the RMS amplitude of the fundamental
input frequency to the RMS amplitude of all other frequency
components at the ADC’s output. The output is band limited
to frequencies above DC and below one half the sampling
frequency. Figure 10 shows a typical spectral content with
a 882kHz sampling rate.
Effective Number of Bits
The Effective Number of Bits (ENOBs) is a measurement
of the resolution of an ADC and is directly related to
S/(N + D) by the equation:
N = [S/(N + D) –1.76]/6.02
119698fa
21
LTC1196/LTC1198
APPLICATIONS INFORMATION
where N is the effective number of bits of resolution and
S/(N + D) is expressed in dB. At the maximum sampling
rate of 1.2MHz with a 5V supply the LTC1196 maintains
above 7.5 ENOBs at 400kHz input frequency. Above 500kHz
the ENOBs gradually decline, as shown in Figure 11, due
to increasing second harmonic distortion. The noise floor
remains low.
50
VREF = VCC = 2.7V
fSMPL = 383kHz (LTC1196)
fSMPL = 287kHz (LTC1198)
7
6
44
VREF = VCC = 5V
fSMPL = 1MHz (LTC1196)
fSMPL = 750kHz (LTC1198)
5
S/(N + D) (dB)
EFFECTIVE NUMBER OF BITS (ENOBs)
8
4
3
(
1
TA = 25°C
1k
10k
100k
INPUT FREQUENCY (Hz)
)
(
) ⎤⎥
⎥⎦
1M
1196/98 G24
Figure 11. Effective Bits and S/(N + D) vs Input Frequency
For input frequencies of 499kHz and 502kHz, the IMD of
the LTC1196/LTC1198 is 51dB with a 5V supply.
Peak Harmonic or Spurious Noise
Total Harmonic Distortion
Total Harmonic Distortion (THD) is the ratio of the RMS
sum of all harmonics of the input signal to the fundamental
itself. The out-of-band harmonics alias into the frequency
band between DC and half of the sampling frequency. THD
is defined as:
THD = 20log
If two pure sine waves of frequencies fa and fb are applied
to the ADC input, nonlinearities in the ADC transfer function can create distortion products at sum and difference
frequencies of mfa ± nfb, where m and n = 0, 1, 2, 3, etc.
For example, the 2nd order IMD terms include (fa + fb)
and (fa – fb) while 3rd order IMD terms include (2fa + fb),
(2fa – fb), (fa + 2fb) and (fa – 2fb). If the two input sine
waves are equal in magnitudes, the value (in dB) of the
2nd order IMD products can be expressed by the following formula:
⎡amplitude fa ± fb
IMD fa ± fb = 20log ⎢
⎢⎣ amplitude att fa
2
0
produce intermodulation distortion (IMD) in addition to
THD. IMD is the change in one sinusoidal input caused
by the presence of another sinusoidal input at a different
frequency.
V22 + V32 + V42 + ... + VN2
V1
where V1 is the RMS amplitude of the fundamental frequency and V2 through VN are the amplitudes of the second
through the Nth harmonics. The typical THD specification
in the Dynamic Accuracy table includes the 2nd through
5th harmonics. With a 100kHz input signal, the LTC1196/
LTC1198 have typical THD of 50dB and 49dB with VCC =
5V and VCC = 3V, respectively.
The peak harmonic or spurious noise is the largest spectral component excluding the input signal and DC. This
value is expressed in dBs relative to the RMS value of a
full-scale input signal.
Full-Power and Full-Linear Bandwidth
The full-power bandwidth is that input frequency at which
the amplitude of the reconstructed fundamental is reduced
by 3dB for a full-scale input.
The full-linear bandwidth is the input frequency at which
the effective bits rating of the ADC falls to 7 bits. Beyond
this frequency, distortion of the sampled input signal
increases. The LTC1196/LTC1198 have been designed to
optimize input bandwidth, allowing the ADCs to undersample input signals with frequencies above the converters’
Nyquist Frequency.
Intermodulation Distortion
If the ADC input signal consists of more than one spectral
component, the ADC transfer function nonlinearity can
119698fa
22
LTC1196/LTC1198
APPLICATIONS INFORMATION
3V VERSUS 5V PERFORMANCE COMPARISON
Table 1. 5V/3V Performance Comparison
Table 1 shows the performance comparison between 3V
and 5V supplies. The power dissipation drops by a factor
of five when the supply is reduced to 3V. The converter
slows down somewhat but still gives excellent performance
on a 3V rail. With a 3V supply, the LTC1196 converts in
1.6μs, samples at 450kHz, and provides a 500kHz linearinput bandwidth.
LTC1196-1
Dynamic accuracy is excellent on both 5V and 3V. The
ADCs typically provide 49.3dB of 7.9 ENOBs of dynamic
accuracy at both 3V and 5V. The noise floor is extremely
low, corresponding to a transition noise of less than 0.1LSB.
DC accuracy includes ±0.5LSB total unadjusted error at
5V. At 3V, linearity error is ±0.5LSB while total unadjusted
error increases to ±1LSB.
5V
3V
50mW
10mW
Max fSMPL
1MHz
383kHz
Min tCONV
600ns
1.6μs
PDISS
INL (Max)
Typical ENOBs
0.5LSB
0.5LSB
7.9 at 300kHz
7.9 at 100kHz
1MHz
500kHz
50mW
10mW
Linear Input Bandwidth (ENOBs > 7)
LTC1198-1
PDISS
PDISS (Shutdown)
15μW
9μW
Max fSMPL
750kHz
287kHz
Min tCONV
600ns
1.6μs
INL (Max)
Typical ENOBs
0.5LSB
0.5LSB
7.9 at 300kHz
7.9 at 100kHz
1MHz
500kHz
Linear Input Bandwidth (ENOBs > 7)
TYPICAL APPLICATIONS
PLD Interface Using the Altera EPM5064
The Altera EPM5064 has been chosen to demonstrate the
interface between the LTC1196 and a PLD. The EPM5064
is programmed to be a 12-bit counter and an equivalent
74HC595 8-bit shift register as shown in Figure 12. The
circuit works as follows: bringing ENA high makes the CS
output high and the EN input low to reset the LTC1196 and
disable the shift register. Bringing ENA low, the CS output
goes high for one CLK cycle with every 12 CLK cycles.
The inverted signal, EN, of the CS output makes the 8-bit
data available on the B0-B7 lines. Figures 13 and 14 show
the interconnection between the LTC1196 and EPM5064
and the timing diagram of the signals between these two
devices. The CLK frequency in this circuit can run up to
fCLK(MAX) of the LTC1196.
VCC
CLK
1μF
3, 14, 25, 36
8-BIT
SHIFT REGISTER
33
DATA
DATA
1
CLK
CLK
B0-B7
B0-B7
EN
CLK
12-BIT
CONVERTER
ENA
ENA
+
–
2
3
4
CS
VCC
+IN
CLK
–IN
GND
LTC1196
DOUT
VREF
8
23
7
34
6
35
ENA
EPM5064
CLK
DATA
5
CS
CS
1196/98 F12
Figure 12. An Equivalent Circuit of the EPM5064
B7
B0
RESERVE PINS OF EPM5064:
2, 4-8,15-20, 22, 24, 26-30
9-13, 21,
31, 32, 43
1
37
38
39
40
41
42
44
1196/98 F13
Figure 13. Interfacing the LTC1196 to the Altera EMP5064 PLD
119698fa
23
LTC1196/LTC1198
TYPICAL APPLICATIONS
DATA
CLK
CS
B7
B6
B5
B4
B3
B2
B1
B0
70
140
210
280
350
420
490
560
630
700 770
840
910
980 1050 1120
TIME (ns)
1196/98 F14
Figure 14. The Timing Diagram
Interfacing the LTC1198 to the TMS320C25 DSP
Figure 15 illustrates the interface between the LTC1198
8-bit data acquisition system and the TMS320C25 digital
signal processor (DSP). The interface, which is optimized
for speed of transfer and minimum processor supervision,
can complete a conversion and shift the data in 4μs with
fCLK = 5MHz. The cycle time, 4μs, of each conversion is
limited by maximum clock frequency of the serial port of
the TMS320C25 which is 5MHz. The supply voltage for the
5MHz CLK
CLKX
CLK
CH0
CH1
CLKR
FSR
TMS320C25
FSX
LTC1198
CS
DX
DIN
DR
DOUT
1196/98 F15
Figure 15. Interfacing the LTC1198 to the TMS320C25 DSP
LTC1198 in Figure 15 can be 2.7V to 6V with fCLK = 5MHz.
At 2.7V, fCLK = 5MHz will work at 25°C. See Recommended
Operating Conditions for limits over temperature.
Hardware Description
The circuit works as follows: the LTC1198 clock line
controls the A/D conversion rate and the data shift rate.
Data is transferred in a synchronous format over DIN and
DOUT . The serial port of the TMS320C25 is compatible
with that of the LTC1198. The data shift clock lines (CLKR,
CLKX) are inputs only. The data shift clock comes from
an external source. Inverting the shift clock is necessary
because the LTC1198 and the TMS320C25 clock the input
data on opposite edges.
The schematic of Figure 15 is fed by an external clock
source. The signal is fed into the CLK pin of the LTC1198
directly. The signal is inverted with a 74HC04 and then
applied to the data shift clock lines (CLKR, CLKX). The
framing pulse of the TMS320C25 is fed directly to the CS
of the LTC1198. DX and DR are tied directly to DIN and
DOUT respectively.
119698fa
24
LTC1196/LTC1198
TYPICAL APPLICATIONS
The timing diagram of Figure 16 was obtained from the
circuit of Figure 15. The CLK was 5MHz for the timing
diagram and the TMS320C25 clock rate was 40MHz.
Figure 17 shows the timing diagram with the LTC1198
running off a 2.7V supply and 5MHz CLK.
VERTICAL: 5V/DIV
CS
The software configures and controls the serial port of
the TMS320C25.
The code first sets up the interrupt and reset vectors. On
reset the TMS320C25 starts executing code at the label
INIT. Upon completion of a 16-bit data transfer, an interrupt is generated and the DSP will begin executing code
at the label RINT.
CLK
DIN
DOUT
1196/98 F16
NULL
BITS
MSB
(B7)
LSB
(B0)
HORIZONTAL: 1500ns/DIV
Figure 16. Scope Trace the LTC1198 Running Off
5V Supply in the Circuit of Figure 15
CS
VERTICAL: 5V/DIV
Software Description
In the beginning, the code initializes registers in the
TMS320C25 that will be used in the transfer routine. The
interrupts are temporarily disabled. The data memory page
pointer register is set to zero. The auxiliary register pointer
is loaded with one and auxiliary register one is loaded with
the value 200 hexadecimal. This is the data memory location where the data from the LTC1198 will be stored. The
interrupt mask register (IMR) is configured to recognize
the RINT interrupt, which is generated after receiving the
last of 16 bits on the serial port. This interrupt is still disabled at this time. The transmit framing synchronization
pin (FSX) is configured to be an output. The F0 bit of the
status register ST1, is initialized to zero which sets up the
serial port to operate in the 16-bit mode.
Next, the code in TXRX routine starts to transmit and
receive data. The DIN word is loaded into the ACC and
shifted left eight times so that it appears as in Figure 18.
This DIN word configures the LTC1198 for CH0 with respect
to CH1. The DIN word is then put in the transmit register
and the RINT interrupt is enabled. The NOP is repeated
3 times to mask out the interrupts and minimize the cycle
time of the conversion to be 20 clock cycles. All clocking
and CS functions are performed by the hardware.
CLK
DIN
DOUT
1196/98 F17
NULL
BITS
MSB
(B7)
LSB
(B0)
HORIZONTAL: 500ns/DIV
Figure 17. Scope Trace the LTC1198 Running Off
1.7V Supply in the Circuit of Figure 15
B15
0
1
START
0
S/D
0
O/S
0
1
DUMMY DUMMY
0
B8
0
L1196/98 F18
Figure 18. DIN Word in ACC of TMS20C25 for the
Circuit in Figure 15
119698fa
25
LTC1196/LTC1198
TYPICAL APPLICATIONS
Once RINT is generated the code begins execution at
the label RINT. This code stores the DOUT word from the
LTC1198 in the ACC and then stores it in location 200
hex. The data appears in location 200 hex right-justified
as shown in Figure 19. The code is set up to continually
loop, so at this point the code jumps to label TXRX and
repeats from here.
LABEL
INIT
TXRX
RINT
MNEMONIC
LSB
MSB
X
X
X
X
X
X
X
X
7
6
5
4
DOUT FROM LTC1198 STORED IN TMS320C25 RAM
3
2
1
0
> 200
L1196/98 F19
Figure 19. Memory Map for the Circuit in Figure 15
COMMENTS
AORG
B
0
INIT
ON RESET CODE EXECUTION STARTS AT 0
BRANCH TO INITIALIZATION ROUTINE
AORG
B
>26
RINT
ADDRESS TO RINT INTERRUPT VECTOR
BRANCH TO RINT SERVICE ROUTINE
AORG
DINT
LDPK
LARP
LRLK
LACK
SACL
STXM
FORT
>32
MAIN PROGRAM STARTS HERE
DISABLE INTERRUPTS
SET DATA MEMORY PAGE POINTER TO 0
SET AUXILIARY REGISTER POINTER TO 1
SET AUXILIARY REGISTER 1 TO >200
LOAD IMR CONFIG WORD INTO ACC
STORE IMR CONFIG WORD INTO IMR
CONFIGURE FSX AS AN OUTPUT
SET SERIAL PORT TO 16-BIT MODE
LACK
SFSM
RPTK
SFL
SACL
EINT
>44
RPTK
NOP
2
MINIMIZE THE CONVERSION CYCLE TIME
TO BE 20 CLOCK CYCLES
ZALS
SACL
B
END
>0
*, 0
TXRX
STORE LTC1198 DOUT WORD IN ACC
STORE ACC IN LOCATION >200
BRANCH TO TRANSMIT RECEIVE ROUTINE
>0
>1
AR1, >200
>10
>4
0
7
>1
LOAD LTC1198 DIN WORD INTO ACC
FSX PULSES GENERATED ON XSR LOAD
REPEAT NEXT INSTRUCTION 8 TIMES
SHIFTS DIN WORD TO RIGHT POSITION
PUT DIN WORD IN TRANSMIT REGISTER
ENABLE INTERRUPT (DISABLE ON RINT)
Figure 20. TMS320C25 Code for the Circuit in Figure 15
119698fa
26
LTC1196/LTC1198
PACKAGE DESCRIPTION
S8 Package
8-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610)
.189 – .197
(4.801 – 5.004)
NOTE 3
.045 ±.005
.050 BSC
8
.245
MIN
7
6
5
.160 ±.005
.150 – .157
(3.810 – 3.988)
NOTE 3
.228 – .244
(5.791 – 6.197)
.030 ±.005
TYP
1
RECOMMENDED SOLDER PAD LAYOUT
.010 – .020
× 45°
(0.254 – 0.508)
.008 – .010
(0.203 – 0.254)
3
4
.053 – .069
(1.346 – 1.752)
.004 – .010
(0.101 – 0.254)
0°– 8° TYP
.016 – .050
(0.406 – 1.270)
NOTE:
1. DIMENSIONS IN
2
.014 – .019
(0.355 – 0.483)
TYP
INCHES
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
.050
(1.270)
BSC
SO8 0303
119698fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
27
LTC1196/LTC1198
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTC1402
12-Bit, 2.2Msps Serial ADC
5V or ±5V Supply, 4.096V or ±2.5V Span
LTC1403/LTC1403A
12-/14-Bit, 2.8Msps Serial ADCs
3V, 15mW, Unipolar Inputs, MSOP Package
LTC1403-1/LTC1403A-1
12-/14-Bit, 2.8Msps Serial ADCs
3V, 15mW, Bipolar Inputs, MSOP Package
LTC1405
12-Bit, 5Msps Parallel ADC
5V, Selectable Spans, 115mW
LTC1407/LTC1407A
12-/14-Bit, 3Msps Simultaneous Sampling ADCs
3V, 2-Channel Differential, Unipolar Inputs, 14mW, MSOP Package
ADCs
LTC1407-1/LTC1407A-1
12-/14-Bit, 3Msps Simultaneous Sampling ADCs
3V, 2-Channel Differential, Bipolar Inputs, 14mW, MSOP Package
LTC1411
14-Bit, 2.5Msps Parallel ADC
5V, Selectable Spans, 80dB SINAD
LTC1412
12-Bit, 3Msps Parallel ADC
±5V Supply, ±2.5V Span, 72dB SINAD
LCT1414
14-Bit, 2.2Msps Parallel ADC
±5V Supply, ±2.5V Span, 78dB SINAD
LTC1420
12-Bit, 10Msps Parallel ADC
5V, Selectable Spans, 72dB SINAD
LTC1604
16-Bit, 333ksps Parallel ADC
±5V Supply, ±2.5V Span, 90dB SINAD
LTC1608
16-Bit, 500ksps Parallel ADC
±5V Supply, ±2.5V Span, 90dB SINAD
LTC1609
16-Bit, 250ksps Serial ADC
5V, Configurable Bipolar/Unipolar Inputs
LTC1864/LTC1865
16-Bit, 250ksps Serial ADCs
5V Supply, 1 and 2 Channel, 4.3mW, MSOP Package
LTC2355-12/ LTC2355-14
12-Bit, 3.5Msps Serial ADCs
3.3V Supply, 0V to 2.5V Span, MSOP Package
LTC2356-12/LTC2356-14
12-/14-Bit, 3.5Msps Serial ADCs
3.3V Supply, ±1.25V Span, MSOP Package
DACs
LTC1666/LTC1667/LTC1668 12-/14-/16-Bit, 50Msps DACs
87dB SFDR, 20ns Settling Time
LTC1592
16-Bit, Serial SoftSpan™ IOUT DAC
±1LSB INL/DNL, Software Selectable Spans
LT1790-2.5
Micropower Series Reference in SOT-23
0.05% Initial Accuracy, 10ppm Drift
LT1461-2.5
Precision Voltage Reference
0.04% Initial Accuracy, 3ppm Drift
LT1460-2.5
Micropower Series Voltage Reference
0.1% Initial Accuracy, 10ppm Drift
References
SoftSpan is a trademark of Linear Technology Corporation.
119698fa
28 Linear Technology Corporation
LT 0108 REV A • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 1993
Similar pages