ETC1 GM7130-ATB5BT 3a step-down voltage regulator Datasheet

GM7130
3A STEP-DOWN VOLTAGE REGULATORS
Power Management
Features
Description
3.3V, 5V, 12V, 15V, Adjustable output versions
The GM7130 series of regulators provide all the active functions
for a step-down (buck) switching regulator, and drive 3A load with
excellent line and load regulation. GM7130's are available in fixed
output voltages of 3.3V, 5V, 12V, 15V, and a versatile Adjustable
output version. These regulators are simple to use and require a
minimum number of external components. Features include internal frequency compensation and a fixed-frequency oscillator. The
GM7130 series are high-efficiency replacements for popular
three-terminal linear regulators, requiring a smaller heatsink or
even no heatsink. The GM7130's perform well with standard
inductors from several manufacturers, simplifying the design of
switch-mode power supplies. The GM7130 series guarantee ±4%
tolerance on output voltage within specified input voltages and
output load conditions, and ±10% on the oscillator frequency.
External shutdown is included, with 50 µA (typical) standby current. The output switch has cycle-by-cycle current limiting, as well
as thermal shutdown for full protection under fault conditions.
Adjustable version output voltage range 1.23V
to 37V ±4% max over line and load conditions
3A output current
Input voltage range 7V to 40V
Requires only 4 external components
High efficiency
TTL shutdown capability, low power standby
mode
Thermal shutdown, current limit protection
Uses standard inductors
52 kHz fixed frequency internal oscillator
Application
Pre-regulator for linear regulators
On-card/ board switching regulators
High-efficiency step-down buck regulator
Positive to negative converter (buck-boost)
TYPICAL APPLICATIONS
Feedback
4
GM7130-5.0
1
+
CIN
100 µF
Output
2
3
GND
+5V
Regulated
Output
3A Load
100 µH
L1
5
ON/ OFF
Revision 1, Jun. 2004
+VIN
+
D1
1N5822
COUT
680 µF
GM 431
www.gammamicro.com
PRELIMINARY
GM7130
7V - 40V
Unregulated
DC Input
1
GM7130
MARKING INFORMATION & PIN CONFIGURATIONS (Top View)
TO-220-5
2
TO-220- 5B
TO-263-5(D PAK)
GM7130
GM7130
GM7130
V VAYWW
VIN
Output
Ground
VIN
VVAYWW
VVAYWW
ON/OFF
Feedback
VIN
Output
Ground
ON/OFF
Feedback
ON/OFF
Feedback
Output
Ground
1 2 3 4 5
V V, VVV
A
Y
WW
= Output Voltage (33 = 3.3V, 120= 12V, A =A dj )
= Assembly Location
=Year
=Work Week
ORDERING INFORMATION
GM7130
Ordering Number
2
Output Voltage
Package
GM7130-ATB5T
Adj
TO-220-5
50 Units / Tube
GM7130-ATB5BT
Adj
TO-220-5B
50 Units / Tube
GM7130-ATA5R
Adj
TO-263-5
800 Units/ Tape & Reel
GM7130-ATA5T
Adj
TO-263-5
50 Units / Tube
GM7130-3.3TB5T
3.3
TO-220-5
50 Units / Tube
GM7130-3.3TB5BT
3.3
TO-220-5B
50 Units / Tube
GM7130-3.3TA5R
3.3
TO-263-5
800 Units/ Tape & Reel
GM7130-3.3TA5T
3.3
TO-263-5
50 Units / Tube
GM7130-5.0TB5T
5.0
TO-220-5
50 Units / Tube
GM7130-5.0TB5BT
5.0
TO-220-5B
50 Units / Tube
GM7130-5.0TA5R
5.0
TO-263-5
800 Units/ Tape & Reel
GM7130-5.0TA5T
5.0
TO-263-5
50 Units / Tube
GM7130-12TB5T
12
TO-220-5
50 Units / Tube
GM7130-12TB5BT
12
TO-220-5B
50 Units / Tube
GM7130-12TA5R
12
TO-263-5
800 Units/ Tape & Reel
GM7130-12TA5T
12
TO-263-5
50 Units / Tube
GM7130-15TB5T
15
TO-220-5
50 Units / Tube
GM7130-15TB5BT
15
TO-220-5B
50 Units / Tube
GM7130-15TA5R
15
TO-263-5
800 Units/ Tape & Reel
GM7130-15TA5T
15
TO-263-5
50 Units / Tube
* TB5B: Bent and Staggered Leads of TO-220 package
** For detail Ordering Number identification, please see last page.
Shipping
GM7130
ABSOLUTE MAXIMUM RATINGS
Rating
Value
Unit
Maximum Supply Voltage
45
V
ON/OFF Pin Input Voltage
-0.3 V VIN
V
-1.0
V
Internally Limited
-
-65 to + 150
°C
+150
°C
Minimum ESD Rating (C=100pF, R=1.5kW)
2
kV
Lead Temperature (Soldering, 10 seconds)
+260
°C
Value
Unit
Output Voltage to Ground (Steady State)
Power Dissipation
Storage Temperature Range
Maximum Junction Temperature
OPERATING RATINGS
Rating
-40
Operating Temperature Range
Supply Voltage
TJ
125
°C
40
V
BLOCK DIAGRAM
+
CIN
V IN
Internal
Regulator
1
ON/OFF
5
ON/OFF
4
Feedback
R2
Fixed Gain
Error AMP
Comparator
+
1.0K
R1
-
3 AMP
Switch
+
Driver
-
Output
VOUT
L1
2
D1
52kHz
Oscillator
Reset
Thermal
Shutdown
Current
Limit
+
C out
3
GND
L
O
A
D
GM 431
1.23V
Band-Gap
Reference
GM7130
Unregulated
DC Input
3
GM7130
ELECTRICAL CHARACTERISTICS: GM7130-3.3
(Specifications with standard type face are for TJ = 25°C, and those with boldface type apply over full Operating Temperature Range)
Conditions
Symbol
Min
Typ
Max
Unit
VIN = 12V, ILOAD = 0.5A
VOUT
3.234
3.3
3.366
V
VIN
VOUT
Parameter
Output Voltage
Output Voltage - GM7130
6V
40V, 0.5A ILOAD 3.0A
h
VIN = 12V, ILOAD = 3.0A
Efficiency
3.168/ 3.135 3.3 3.432/ 3.465
-
75
-
V
%
ELECTRICAL CHARACTERISTICS: GM7130-5.0
(Specifications with standard type face are for TJ = 25°C, and those with boldface type apply over full Operating Temperature Range)
Conditions
Symbol
Min
Typ
Max
Unit
VIN = 12V, ILOAD = 0.5A
VOUT
4.900
5.0
5.100
V
Parameter
Output Voltage
Output Voltage - GM7130
8V
VIN
40V, 0.5A ILOAD 3.0A
VIN = 12V, ILOAD = 3.0A
Efficiency
VOUT
h
4.800/ 4.750 5.0 5.200/ 5.250
-
77
V
-
%
ELECTRICAL CHARACTERISTICS: GM7130-12
(Specifications with standard type face are for TJ = 25°C, and those with boldface type apply over full Operating Temperature Range)
Parameter
Output Voltage
Output Voltage - GM7130
Efficiency
15V
Conditions
Symbol
Min
Typ
Max
Unit
VIN = 25V, ILOAD = 0.5A
VOUT
11.76
12.0
12.24
V
VIN 40V, 0.5A ILOAD 3.0A
VOUT
VIN = 15V, ILOAD = 3.0A
h
11.52/ 11.40 12.0 12.48/ 12.60
-
88
V
-
%
ELECTRICAL CHARACTERISTICS: GM7130-15
(Specifications with standard type face are for TJ = 25°C, and those with boldface type apply over full Operating Temperature Range)
GM7130
Parameter
4
Output Voltage
Output Voltage - GM7130
Efficiency
Conditions
Symbol
Min
Typ
Max
Unit
VIN = 25V, ILOAD = 0.5A
VOUT
14.70
15.0
15.30
V
18V VIN 40V, 0.5A ILOAD 3.0A
VOUT
VIN = 18V, ILOAD = 3.0A
h
14.40/14.25 15.0 15.60/ 15.75
-
88
-
V
%
GM7130
ELECTRICAL CHARACTERISTICS: GM7130-ADJ
(Specifications with standard type face are for TJ = 25°C, and those with boldface type apply over full Operating Temperature Range)
Conditions
Symbol
Min
Typ
Max
Unit
VIN = 12V, ILOAD = 0.5A, VOUT = 5V
VOUT
1.217
1.230
1.243
V
Parameter
Feedback Voltage
Feedback Voltage - GM7130
Efficiency
8V VIN 40V, 0.5A ILOAD 3.0A
VOUT
VOUT = 5V
1.193/1.180 1.230 1.267/1.280
-
h
VIN = 12V, ILOAD = 3A, VOUT=5V
-
77
V
%
ELECTRICAL CHARACTERISTICS: All Output Voltage Versions
(Specifications with standard type face are for TJ = 25 C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise
Parameter
Feedback Bias Current
Oscillator Frequency
Saturation Voltage
Max Duty Cycle (ON)
Current Limit
Output Leakage Current
Quiescent Current
Standby Quiescent Current
Thermal Resistance
ON/OFF Pin
Logic Input Level
Conditions
Symbol
Min
Typ
Max
Unit
VOUT = 5V (Adjustable Version Only)
Ib
-
50
100 / 500
nA
(Note 11)
fo
47 / 42
52
58 / 63
kHz
IOUT = 3A (Notes 4)
VSAT
-
1.4
1.8 / 2.0
V
(Note 5)
DC
93
98
-
%
(Note 4, 11)
ICL
4.2 / 3.5
5.8
6.9 / 7.5
A
IL
-
7.5
2
30
mA
IQ
-
5
10
mA
ISTBY
-
50
200
µA
TO-220 Package, Junction to Ambient (Note 8)
qJA
TO-220 Package, Junction to Ambient (Note 9)
qJA
TO-220,TO-263 Package, Junction to Case
qJC
qJA
65
45
2
50
--
°C/W
TO-263 Package, Junction to Ambient (Note 10)
-
VOUT=0V
VIH
2.2 / 2.4
1.4
-
V
VOUT = Nominal Output Voltage
VIL
-
1.2
1.0 / 0.8
V
ON/OFF Pin = 5V (OFF)
IIH
-
12
30
µA
ON/OFF Pin = 0V (ON)
IIL
-
0
10
µA
(Notes 6, 7)
Output = -1 V
Output = -1V
(Note 6)
ON/OFF Pin = 5V (OFF)
ON/OFF Pin Input Current
GM 431
GM7130
specified, VIN= 12V for the 3.3V, 5.0V and ADJ version, VIN= 25V for 12V version. and VIN= 30V for 15V version. ILOAD = 500 mA)
5
GM7130
ELECTRICAL CHARACTERISTICS
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.
Operating Ratings indicate conditions for which the device is intended to be functional, but do not
guarantee specific performance limits. Guaranteed specifications and Test conditions are shown in
Electrical Characteristics.
Note 2: All limits guaranteed at 25°C (standard type face) and over full operating temperature range (bold
type face). All 25°C limits are 100% production tested. All limits over full operating temperature
range are guaranteed via correlation using standard Statistica Quality Control methods.
Note 3: External components such as the catch diode, inductor, input and output capacitors can affect
switching regulator system performance. When the GM7130 is used as shown in the Figure 1 test
circuit, system performance will be as shown in system parameters section of Electrical
Characteristics.
Note 4: Output pin sourcing current. No diode, inductor or capacitor connected to output.
Note 5: Feedback pin removed from output and connected to 0V.
Note 6: Feedback pin removed from output and connected to +12V for the Adjustable, 3.3V, and 5V
versions, and +25V for the 12V and 15V versions, to force the output transistor OFF.
Note 7: VIN = 40V
Note 8: Junction to ambient thermal resistance (no external heat sink) for the 5 lead TO-220 package
mounted vertically, with ½ inch leads in a socket, or on a PC board with minimum copper area.
Note 9: Junction to ambient thermal resistance (no external heat sink) for the 5 lead TO-220 package
mounted vertically, with ¼ inch leads soldered to a PC board containing approximately 4 square
inches of copper area surrounding the leads.
Note 10: If the TO-263 package is used, the thermal resistance can be reduced by increasing the PC board
Copper area thermally connected to the package. Using 0.5 square inches of copper area, qJA is
50°C//W, with 1 square inch of copper area, qJA is 37°C/W, and with 1.6 or more square inches of
copper area, qJA is 32°C/W.
GM7130
Note 11: The oscillator frequency reduces to approximately 11 kHz in the event of an output short or an
Overload which causes the regulated output voltage to drop approximately 40% from the nominal
output voltage. This self- protection feature lowers the Average power dissipation of the GM7130
By lowering the minimum duty cycle from 5% down to approximately 2%.
6
GM7130
TEST CIRCUIT AND LAYOUT GUIDELINES
Careful layout is important with any switching regulator. Rapidly switching currents associated with wiring
inductance generate voltage transients which can cause problems. To minimize inductance and ground loops,
the lengths of the leads indicated by heavy lines in Figure 1 below should be kept as short as possible. Singlepoint grounding (as indicated in Figure 1) or ground plane construction should be used for best results. When
using the Adjustable version, place the programming resistors as close as possible to the GM7130, to keep the
sensitive feedback wiring short.
Figure 1(a). Fixed Output Voltage Versions
Feedback
4
GM 7130-
+VIN
FIXED OUTPUT
1
L1
Output
2
GND 3
VIN
Unregulated
DC Input
+
VOUT
100 µH
ON/OFF 5
+
CIN
100 µF
L
O
A
D
D1
COUT
680 µF
CIN - 100 µF, 75V, Aluminum Electrolytic
COUT - 680 µF, 25V, Aluminum Electrolytic
D1 - Schottky, MBR360
L1 - 100 µH, 3L Electronic Corp. TC-101M-3.0A-6826
R1 - 2k, 0.1%
R2 - 6.12k, 0.1%
Feedback
4
GM7130-ADJ
1
2
7V - 40V
Unregulated
DC Input
L1
Output
GND 3
VOUT=5.0V
100 µH
ON/ OFF 5
+
+
CIN
100 µF
D1
MBR360
VOUT = VREF ( 1 +
COUT
680 µF
R2
R1
L
O
A
D
R2
)
R1
where VREF = 1.23V, R1 between 1k and 5k.
Figure 1(b). Adjustable Output Voltage Versions
GM 431
VOUT
R2 = R1 ( V
-1)
REF
GM7130
+VIN
7
GM7130
Typical Performance Characteristics
Figure 3. Current Limit
Figure 2. Switch Saturation Voltage
1.6
6.5
VIN = 25V
1.2
OUTPUT CURRENT (A)
SATURATION VOLTAGE (V)
1.4
-55°C
1.0
0.8
25°C
0.6
150 °C
0.4
6.0
5.5
5.0
4.5
0.2
4.0
0
0
0.5
1.0
1.5
2.0
2.5
3.0
-75 -50 -25
SWITCH CURRENT (A)
Figure 4. Dropout Voltage
L1 = 150 µH
1.5
ILOAD = 1A
1.0
ILOAD = 200mA
0.5
25
50
VOUT = 5V
Measured at
Ground Pin
TJ = 25°
18
16
14
12
10
ILOAD = 3A
8
6
RIND = 0.1W
0
4
75 100 125 150
ILOAD = 200mA
0
10
20
30
40
50
60
INPUT VOLTAGE (V)
Figure 6. Standby Quiescent Current
Figure 7. Minimum Operating Voltage
200
5.0
VIN = 40V
Adjustable Version Only
4.5
4.0
150
INPUT VOLTAGE (V)
SATURATION QUIESCENT CURRENT (µA)
GM7130
JUNCTION TEMPERATURE (°C)
8
50 75 100 125 150
Figure 5. Quiescent Current
ILOAD = 3A
0
-75 -50 -25
25
20
QUIESCENT CURRENT(mA)
INPUT-OUTPUT DIFFERENTIAL (V)
2.0
0
JUNCTION TEMPERATURE (°C)
V ON / OFF = 5V
100
50
3.0
2.5
2.0
1.5
1.0
VIN = 12V
0.5
0
-50 -25
0
25 50
75 100
JUNCTION TEMPERATURE (°C)
3.5
125
0
-50
VOUT 1.23V
ILOAD = 500 mA
-25
0
25 50
75 100 125
JUNCTION TEMPERATURE (°C)
GM7130
Typical Performance Characteristics
Figure 9. Feedback Voltage vs. Duty Cycle
Figure 8. Quiescent Current vs. Duty Cycle
20.0
Adjustable Version Only
FEEDBACK VOLTAGE CHANGE (mV)
QUIESCENT CURRENT (mA)
20.0
17.5
VIN = 7V
15.0
12.5
VIN = 40V
10.0
7.5
5.0
2.5
ILOAD = 500mA
0
0
20
40
Adjustable Version Only
ILOAD = 500mA
15.0
10.0
5.0
VIN = 40V
0
VIN = 7V
-5.0
-10.0
-15.0
-20.0
60
80
100
0
DUTY CYCLE (%)
20
40
60
80
100
DUTY CYCLE (%)
Figure 10. Maximum Power Dissipation(TO-263)
Figure 11. Feedback Pin Current
100
qJA = 32°C/ W
qJA = 37°C/ W
3
2
1
qJA = 50°C/ W
qJA = 73°C/ W
0
0
10 20 30 40 50 60 70 80 90 100
AMBIENT TEMPERATURE (°C)
50
25
0
-25
-50
-75
-100
-75 -50 -25 0 25 50 75 100 125 150
JUNCTION TEMPERATURE (°C)
GM7130
4
FEEDBACK PIN CURRENT (nA)
POWER DISSIPATION (W)
Adjustable Version Only
75
9
GM7130
Typical Performance Characteristics
Figure 12. Switching Waveforms
Figure 13. Load Transient Response
Output
Voltage
Change
100mv/ div
Inductor
Current
1A/ div
3A
Load
Current
1kHz
10mA
1.5
2
2.5
15
68µH
0.4 0.5 0.6 0.70.8 1.0
1.5
µH
H
00
0µ
H
0µ
7
0.3 0.4 0.5 0.60.8
2.0 2.5 3.0
0µ
H
0µ
H
47
H
µH
0µ
H
0µ
47
1 1.2 1.5
2
MAXIMUM LOAD CURRENT(A)
MAXIMUM LOAD CURRENT(A)
Figure 14. GM7130 -3.3
Figure 15. GM7130 - 12
Figure 16. GM7130 -5.0
100
90
80
00
10
00
µH
68
70
0
0µ
H
33
50
45
40
0µ
H
22
35
0µ
1. Programming Output Voltage(Selecting R1 and R2, as shown in Figure 12.
And Figure 13.
H
15
H
0µ
0
10
µH
Use the following formula to select the appropriate resistor values.
68
30
25
20
0.3
2.5 3
VOUT = Regulated Output Voltage
VIN(Max) = Maximum Input Voltage
ILOAD(Max) = Maximum Load Current
F = Switching Frequency (Fixed at 52 kHz)
µH
47
60
µH
PROCEDURE(Adjustable Output Voltage Versions)
Given:
µH
µH
15
0.4 0.5 0.6 0.7 0.8 1.0
1.5
2..0 2.5 3.0
VOUT = VREF ( 1+
Figure 17. GM7130 - ADJ
VOUT
1,000
E • T = (VIN - VOUT)
•
VIN
F(in kHz)
R2
)
R1
where VREF = 1.23V
R1 can be between 1k and 5k. (For best temperature coefficient and stability
with time, use 1% metal film resistors)
MAXIMUM LOAD CURRENT(A)
GM7130
8
MAXIMUM LOAD CURRENT(A)
150
10
10
9
68
100µH
12
10
150µH
16
15
22
220µH
10
µH
18
20
68
µH
00
00
330µH
20
14
0.3
3
470µH
15
µH
68
1
680µH
33
H
0µ
10
5
0.3 0.4 0.5 0.6 0.8
H
MAXIMUM INPUT VOLTAGE(V)
H
15
0µ
H
0µ
µ
47
6
25
40
10
H
0µ
22
7
40
35
30
15
H
8
MAXIMUM INPUT VOLTAGE(V)
MAXIMUM INPUT VOLTAGE(V)
H
0µ
68
33
10
0µ
40
20
15
47
MAXIMUM INPUT VOLTAGE(V)
Input : 12V
Output : 5V @3A
R2 = R1 (
VOUT
-1)
VREF
EXAMPLE (Adjustable Output Voltage Versions)
Given:
VOUT = 10V
VIN(Max) = 25V
ILOAD(Max) =3A
F = 52kHz
1. Programming Output Voltage (Selecting R1 and R2)
R2
VOUT = 1.23 (1+
) Select R1 = 1k
R1
V
10V
R2 = R1( OUT -1) = 1k (
-1)
1.23V
VREF
R2 = 1k (8.13 - 1) = 7.13k, closest 1% value is 7.15k
GM7130
Inductor Selection by Manufacturer's Part Numbe.
Inductor Value
3L Electronic Corp.
47µH
TC-470M-3A-5026
68µH
TC-680M-3A-5026
100µH
TC-101M-3A-5026
150µH
TC-151M-3A-8026
220µH
TC-221M-3A-8026
330µH
TC-331M-3A-8026
470µH
TC-471M-3A-8026
680µH
TC-681M-3A-8026
1000µH
TC-102M-3A-9426
1500µH
TC-152M-3A-9426
3L Electronic Corp., + 886(2) 86659999
Website : www.3lcoil.com.tw
Capacitor Selection by Manufacturer's Part Number
Capacitor Value
Nippon ChemiI - Con Corp.
100µF
KY50VB100-MH11
220µF
KY50VB220-MJ16
470µF
680µF
KY50VB470-MJ30
KY50VB680-MK30
1000µF
KY50VB1000-ML25
GM7130
Nippon Chemi-Con Corp. , + 81(3)54367628
Website : www.chemi-con.co.jp
11
GM7130
TO-220-5 PACKAGE OUTLINE DIMENSIONS
9.97 ± 0.20
4.50 ± 0.20
9.90 ± 0.20
3.60 ± 0.20
8.0 ± 0.20
8.70
2.80 ± 0.10
7.0
+0.1
1.30 -0.05
3.70 ± 0.20
4.60
28.78 MAX
8.40
P
3°
15.90 ± 0.20
1.50 DP0.20
9.20 ± 0.20
1.30 ± 0.10
1.70
1.2
3°
7.0 ± 0.20
9.20 ± 0.20
3°
13.08 ± 0.20
3-R0.2
5-0.8 ± 0.10
+0.1
0.50 -0.05
2.40 ± 0.20
1.7(TYP)
3°
3°
2 - R 0.3
Unit: mm
10.00 ± 0.20
TO-263-5 PACKAGE OUTLINE DIMENSIONS
9.90
4.50
1.30
15°
0.40
1.20
3°
4.60
1.50 DP0.20
9.20
Pad Layout
1.20
4.90
GM7130
1.70 TYP
(1.70 ± 0.20)
0.80
0.40
3°
2.00
17.5
9
2.40
R0.30
0.75
R0.30
3.8
1.7
2.54
0.50
11.5
P
0.10
15.3
10.0
8.0
7.0
4.40
1.07
1.75
3°
3°
R 0.3
0.90
R 0.45
7.2
Units: mm
9.20
15.30
10.00
12
4.90
Unit: mm
GM7130
TO-220-5B PACKAGE OUTLINE DIMENSIONS
0.18 ± 0.004
4.57 ± 0.1
0.4 ± 0.006
10.16 ± 0.15
0.108 ± 0.006
0.74 ± 0.15
0.05 ± 0.005
1.27 ± 0.1
0.151 ± 0.002
3.84 ± 0.05
C
0.4985 ± 0.0075
12.66 ± 0.2
0.032 ± 0.004
0.81 ± 0.1
0.05 ± 0.005
1.27 ± 0.1
0.965 ± 0.008
24.5 ± 0.2
0.138 ± 0.004
3.5 ± 0.1
0.220
1.700
0.996 ± 0.008
25.3± 0.2
0.105 ± 0.006
2.76± 0.17
0.153 ± 0.0035
3.9 ± 0.1
0.213 ± 0.004
5.4 ± 0.1
0.358 ± 0.008
9.1± 0.2
0.173 ± 0.006
4.4 ± 0.15
0.331 ± 0.006 0.017 ± 0.005
0.42 ± 0.11
8.4 ± 0.15
0.268 ± 0.004
0.68 ± 0.1
(
Inches
)
mm
ORDERING NUMBER
GM 7130 A TB5 T
Shipping
R: Tape & Reel
T: Tube
Gamma Micro.
Package
TA5: TO-263-5
TB5: TO-220-5
TB5B: TO-220-5B
Output Voltage
A: Adj, 3.3: 3.3V
5.0: 5.0V, 12: 12V
15: 15V
GM7130
Circuit Type
13
Similar pages