AD EVAL-AD7767-2EDZ 24-bit, 8.5 mw, 109 db, 128/64/32 ksps adc Datasheet

24-Bit, 8.5 mW, 109 dB,
128/64/32 kSPS ADCs
AD7767
FEATURES
GENERAL DESCRIPTION
Oversampled successive approximation (SAR) architecture
High performance ac and dc accuracy, low power
115.5 dB dynamic range, 32 kSPS (AD7767-2)
112.5 dB dynamic range, 64 kSPS (AD7767-1)
109.5 dB dynamic range, 128 kSPS (AD7767)
−118 dB THD
Exceptionally low power
8.5 mW, 32 kSPS (AD7767-2)
10.5 mW, 64 kSPS (AD7767-1)
15 mW, 128 kSPS (AD7767)
High dc accuracy
24 bits, no missing codes (NMC)
INL: ±3 ppm (typical), ±7.6 ppm (maximum)
Low temperature drift
Zero error drift: 15 nV/°C
Gain error drift: 0.0075% FS
On-chip low-pass FIR filter
Linear phase response
Pass-band ripple: ±0.005 dB
Stop-band attenuation: 100 dB
2.5 V supply with 1.8 V/2.5 V/3 V/3.6 V logic interface options
Flexible interfacing options
Synchronization of multiple devices
Daisy chain capability
Power-down function
Temperature range: −40°C to +105°C
The AD7767/AD7767-1/AD7767-2 are high performance
24-bit oversampled SAR analog-to-digital converters (ADC).
The AD7767/AD7767-1/AD7767-2 combine the benefits of a
large dynamic range and input bandwidth, consuming 15 mW,
10.5 mW, and 8.5 mW power, respectively, all contained in a
16-lead TSSOP package.
Ideal for ultralow power data acquisition (such as PCI- and
USB-based systems), the AD7767/AD7767-1/AD7767-2
provide 24-bit resolution. The combination of exceptional SNR,
wide dynamic range, and outstanding dc accuracy make the
AD7767/AD7767-1/AD7767-2 ideally suited for measuring
small signal changes over a wide dynamic range. This is
particularly suitable for applications where small changes on the
input are measured on larger ac or dc signals. In such an
application, the AD7767/AD7767-1/AD7767-2 accurately
gather both ac and dc information.
The AD7767/AD7767-1/AD7767-2 include an on-board digital
filter (complete with linear phase response) that acts to eliminate out-of-band noise by filtering the oversampled input
voltage. The oversampled architecture also reduces front-end
antialias requirements. Other features of the AD7767 include a
SYNC/PD (synchronization/power-down) pin, allowing the
synchronization of multiple AD7767 devices. The addition of
an SDI pin provides the option of daisy chaining multiple
AD7767 devices.
The AD7767/AD7767-1/AD7767-2 operate from a 2.5 V supply
using a 5 V reference. The devices operate from −40°C to +105°C.
APPLICATIONS
Low power PCI/USB data acquisition systems
Low power wireless acquisition systems
Vibration analysis
Instrumentation
High precision medical acquisition
RELATED DEVICES
Table 1. 24-Bit Analog-to-Digital Converters
Part No.
AD7760
FUNCTIONAL BLOCK DIAGRAM
AVDD AGND MCLK
AD7762/
AD7763
DVDD VDRIVE DGND
VREF+
VIN+
REFGND
AD7767/
AD7767-1/
AD7767-2
SYNC/PD
SERIAL INTERFACE
AND
CONTROL LOGIC
SCLK DRDY SDO
SDI
CS
06859-001
VIN–
AD7764
DIGITAL
FIR FILTER
SUCCESSIVEAPPROXIMATION
ADC
Figure 1.
AD7765
AD7766
AD7766-1
AD7766-2
1
Description
2.5 MSPS, 100 dB dynamic range 1 , on-board differential
amp and reference buffer, parallel, variable decimation
625 kSPS, 109 dB dynamic range1, on-board differential
amp and reference buffer, parallel/serial, variable
decimation
312 kSPS, 109 dB dynamic range1, on-board differential
amp and reference buffer, variable decimation (pin)
156 kSPS, 112 dB dynamic range1, on-board differential
amp and reference buffer, variable decimation (pin)
128 kSPS, 109.5 dB1, 15 mW, 16-bit INL, serial interface
64 kSPS 112.5 dB1,10.5 mW, 16-bit INL, serial interface
32 kSPS, 115.5 dB1, 8.5 mW, 16-bit INL, serial interface
Dynamic range at maximum output data rate.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2007 Analog Devices, Inc. All rights reserved.
AD7767
TABLE OF CONTENTS
Features .............................................................................................. 1
AD7767 Interface ........................................................................... 17
Applications....................................................................................... 1
Initial Power-Up ......................................................................... 17
Functional Block Diagram .............................................................. 1
Reading Data............................................................................... 17
General Description ......................................................................... 1
Power-Down, Reset, and Synchronization ............................. 17
Revision History ............................................................................... 2
Daisy Chaining ............................................................................... 18
Specifications..................................................................................... 3
Reading Data in Daisy Chain Mode ........................................ 18
Timing Specifications .................................................................. 5
Choosing the SCLK Frequency ................................................ 18
Timing Diagrams.......................................................................... 6
Daisy Chain Mode Configuration and Timing Diagrams.... 19
Absolute Maximum Ratings............................................................ 8
Driving the AD7767....................................................................... 20
ESD Caution.................................................................................. 8
Differential Signal Source ......................................................... 20
Pin Configuration and Function Descriptions............................. 9
Single-Ended Signal Source ...................................................... 20
Typical Performance Characteristics ........................................... 10
Antialiasing ................................................................................. 21
Terminology .................................................................................... 14
Power Dissipation....................................................................... 21
Theory of Operation ...................................................................... 15
VREF+ Input Signal ....................................................................... 22
AD7767/AD7767-1/AD7767-2 Transfer Function................ 15
Multiplexing Analog Input Channels ...................................... 22
Converter Operation.................................................................. 15
Outline Dimensions ....................................................................... 23
Analog Input Structure.............................................................. 16
Ordering Guide .......................................................................... 23
Supply and Reference Voltages ................................................. 16
REVISION HISTORY
8/07—Revision 0: Initial Version
Rev. 0 | Page 2 of 24
AD7767
SPECIFICATIONS
AVDD = DVDD = 2.5 V ± 5%, VDRIVE = 1.8 V to 3.6 V, VREF = 5 V, MCLK = 1 MHz, common-mode input = VREF/2, TA = −40°C to +105°C,
unless otherwise noted.
Table 2.
Parameter
OUTPUT DATA RATE
AD7767
AD7767-1
AD7767-2
ANALOG INPUT 1
Differential Input Voltage
Absolute Input Voltage
Test Conditions/Comments
AD7767-1
Dynamic Range2
Signal-to-Noise Ratio (SNR)2
Spurious Free Dynamic Range (SFDR)2
Total Harmonic Distortion (THD)2
Intermodulation Distortion (IMD)2
AD7767-2
Dynamic Range2
Signal-to-Noise Ratio (SNR)2
Spurious Free Dynamic Range (SFDR)2
Total Harmonic Distortion (THD)2
Intermodulation Distortion (IMD)2
DC ACCURACY1
Resolution
Differential Nonlinearity2
Integral Nonlinearity2
Zero Error2
Gain Error2
Zero Error Drift2
Gain Error Drift2
Common-Mode Rejection Ratio2
Typ
Decimate by 8
Decimate by 16
Decimate by 32
VIN+ − VIN−
VIN+
−0.1
VIN−
Common-Mode Input Voltage
Input Capacitance
DYNAMIC PERFORMANCE
AD7767
Dynamic Range 2
Signal-to-Noise Ratio (SNR)2
Spurious Free Dynamic Range (SFDR)2
Total Harmonic Distortion (THD)2
Intermodulation Distortion (IMD)2
Min
−0.1
VREF/2 − 5%
Decimate by 8, ODR = 128 kHz
Shorted inputs
Full-scale input amplitude, 1 kHz tone
Full-scale input amplitude, 1 kHz tone
Full-scale input amplitude, 1 kHz tone
Tone A = 49.7 kHz, Tone B = 53 kHz
Second-order terms
Third-order terms
Decimate by 16, ODR = 64 kHz
Shorted inputs
Full-scale input amplitude, 1 kHz tone
Full-scale input amplitude, 1 kHz tone
Full-scale input amplitude, 1 kHz tone
Tone A = 24.7 kHz, Tone B = 25.3 kHz
Second-order terms
Third-order terms
Decimate by 32, ODR = 32 kHz
Shorted inputs
Full-scale input amplitude, 1 kHz tone
Full-scale input amplitude, 1 kHz tone
Full-scale input amplitude, 1 kHz tone
Tone A = 11.7 kHz, Tone B = 12.3 kHz
Second-order terms
Third-order terms
For all devices
No missing codes
Guaranteed monotonic to 24 bits
18-bit linearity
50 Hz tone
Rev. 0 | Page 3 of 24
108
107
111
110
VREF/2
22
109.5
108.5
−128
−118
Max
Unit
128
64
32
kHz
kHz
kHz
±VREF
+VREF + 0.1
V p-p
V
+VREF + 0.1
VREF/2 + 5%
V
V
pF
−116
−105
−133
−109
dB
dB
112.5
111.5
−128
−118
dB
dB
dB
dB
dB
dB
dB
−116
−105
−133
−108
114
112
dB
dB
dB
dB
115.5
113.5
−128
−118
−116
−105
−137
−108
24
dB
dB
dB
dB
dB
dB
dB
Bits
3
20
0.0075
15
0.4
−110
±7.6
0.075
ppm
μV
% FS
nV/°C
ppm/°C
dB
AD7767
Parameter
DIGITAL FILTER RESPONSE1
Group Delay
Settling Time (Latency)
Pass-Band Ripple
Pass Band
−3 dB Bandwidth
Stop Band Frequency
Stop-Band Attenuation
REFERENCE INPUT1
VREF+ Input Voltage
DIGITAL INPUTS (Logic Levels)1
VIL
VIH
Input Leakage Current
Input Capacitance
Master Clock Rate
Serial Clock Rate
DIGITAL OUTPUTS1
Data Format
VOL
VOH
POWER REQUIREMENTS1
AVDD
DVDD
VDRIVE
CURRENT SPECIFICATIONS
AD7767 (Operational Current)
AIDD
DIDD
IREF
AD7767-1 (Operational Current)
AIDD
DIDD
IREF
AD7767-2 (Operational Current)
AIDD
DIDD
IREF
Static Current (MCLK Stopped)
AIDD
DIDD
Power-Down Mode Current
AIDD
DIDD
POWER DISSIPATION
AD7767 (Operational Power)
AD7767-1 (Operational Power)
AD7767-2 (Operational Power)
1
2
Test Conditions/Comments
Min
Typ
Max
37/ODR
74/ODR
Complete settling
±0.005
0.453 × ODR
0.49 × ODR
0.547 × ODR
100
μs
μs
dB
Hz
Hz
Hz
dB
+2.4
2 × AVDD
V
−0.3
0.7 × VDRIVE
0.3 × VDRIVE
VDRIVE + 0.3
±1
V
V
μA/pin
pF
MHz
Hz
5
1.024
1/t8
Serial 24 bits, twos complement (MSB
first)
ISINK = +500 μA
ISOURCE = −500 μA
Unit
0.4
VDRIVE – 0.3
± 5%
± 5%
+1.7
V
V
+2.5
+2.5
+2.5
+3.6
V
V
V
1.3
3.9
0.35
1.5
4.8
0.425
mA
mA
mA
1.3
2.2
0.35
1.5
2.85
0.425
mA
mA
mA
1.3
1.37
0.35
1.5
1.86
0.425
mA
mA
mA
0.9
1
1
93
mA
μA
0.1
1
6
93
μA
μA
15
10.5
8.5
18
13
10.5
mW
mW
mW
MCLK = 1.024 MHz
128 kHz output data rate
64 kHz output data rate
32 kHz output data rate
For all devices
For all devices
MCLK = 1.024 MHz
128 kHz output data rate
64 kHz output data rate
32 kHz output data rate
Specifications for all devices, AD7767, AD7767-1, and AD7767-2.
See the Terminology section.
Rev. 0 | Page 4 of 24
AD7767
TIMING SPECIFICATIONS
AVDD = DVDD = 2.5 V ± 5%, VDRIVE = 1.7 V to 3.6 V, VREF = 5 V, common-mode input = VREF/2, TA = −40°C (TMIN) to +105°C (TMAX),
unless otherwise noted 1
Table 3.
Parameter
DRDY Operation
t1
t2 2
t3
t4
Limit at TMIN, TMAX
Unit
Description
510
100
900
265
128
71
294
435
492
MCLK rising edge to DRDY falling edge
MCLK high pulse width
MCLK low pulse width
MCLK rising edge to DRDY rising edge (AD7767)
MCLK rising edge to DRDY rising edge (AD7767-1)
MCLK rising edge to DRDY rising edge (AD7767-2)
DRDY pulse width (AD7767)
DRDY pulse width (AD7767-1)
DRDY pulse width (AD7767-2)
DRDY low period, read data during this period
tREAD 3
t DRDY − t5
ns typ
ns min
ns max
ns typ
ns typ
ns typ
ns typ
ns typ
ns typ
ns typ
t DRDY 3
n × 8 × tMCLK
ns typ
DRDY period
0
6
60
50
25
24
10
10
10
1/t8
6
0
ns min
ns max
ns max
ns max
ns max
ns max
ns min
ns min
ns min
min
ns max
ns min
DRDY falling edge to CS setup time
CS falling edge to SDO three-state disabled
Data access time after SCLK falling edge (VDRIVE = 1.7 V)
Data access time after SCLK falling edge (VDRIVE = 2.3 V)
Data access time after SCLK falling edge (VDRIVE = 2.7 V)
Data access time after SCLK falling edge (VDRIVE = 3.0 V)
SCLK falling edge to data valid hold time (VDRIVE = 3.6 V)
SCLK high pulse width
SCLK low pulse width
Minimum SCLK period
Bus relinquish time after CS rising edge
CS rising edge to DRDY rising edge
0
0
ns min
ns max
DRDY falling edge to data valid setup time
DRDY rising edge to data valid hold time
1
2
ns min
ns max
SDI valid to SCLK falling edge setup time
SCLK falling edge to SDI valid hold time
1
20
1
510
592 × (n + 2)
ns typ
ns typ
ns min
ns typ
tMCLK
SYNC/PD falling edge to MCLK rising edge
MCLK rising edge to DRDY rising edge going into SYNC/PD
SYNC/PD rising edge to MCLK rising edge
MCLK rising edge to DRDY falling edge coming out of SYNC/PD
Filter settling time after a reset or power-down
t5
Read Operation
t6
t7
t8
t9
t10
t11
tSCLK
t12
t13
Read Operation with CS Low
t14
t15
Daisy Chain Operation
t16
t17
SYNC/PD Operation
t18
t19
t20
t21
tSETTLING3
1
Sample tested during initial release to ensure compliance. All input signals are specified with tr = tf = 5 ns (10% to 90% of DVDD) and timed from a voltage level of 1.7 V.
t2 and t3 allow a ~90% to 10% duty cycle to be used for the MCLK input where the minimum is 10% for the clock high time and 90% for MCLK low time. The maximum
MCLK frequency is 1.024 MHz.
3
n = 1 for AD7767, n = 2 for the AD7767-1, n = 4 for the AD7767-2.
2
Rev. 0 | Page 5 of 24
AD7767
TIMING DIAGRAMS
t2
1
MCLK
8×n
t3
1
8×n
t4
t5
t1
t5
06859-002
tREAD
DRDY
tDRDY
Figure 2. DRDY vs. MCLK Timing Diagram, n = 1 for AD7767 (Decimate by 8), n = 2 for AD7767-1 (Decimate by 16), n = 4 for AD7767-2 (Decimate by 32)
tDRDY
tREAD
DRDY
t13
t6
CS
t10
1
t8
t7
SDO
23
t11
t9
t12
MSB
D22
D21
D20
D1
06859-003
SCLK
LSB
Figure 3. Serial Timing Diagram, Reading Data Using CS
CS = 0
tDRDY
tREAD
DRDY
t14
t10
1
SCLK
23
t8
DATA
INVALID
MSB
D22
t11
t9
D21
D20
t15
D1
LSB
DATA
INVALID
06859-004
SDO
24
Figure 4. Serial Timing Diagram, Reading Data Setting CS Logic Low
Rev. 0 | Page 6 of 24
AD7767
PART OUT OF POWER-DOWN
FILTER RESET
BEGINS SAMPLING
PART IN POWER-DOWN
MCLK (I)
A
B
t18
C
D
t20
SYNC/PD (I)
t21
t19
DOUT (O)
VALID DATA
INVALID DATA
Figure 5. Reset, Synchronization, and Power-Down Timing Diagram
Rev. 0 | Page 7 of 24
VALID DATA
06859-005
tSETTLING
DRDY (O)
AD7767
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 4.
Parameter
AVDD to AGND
DVDD to DGND
AVDD to DVDD
VREF+ to REFGND
REFGND to AGND
VDRIVE to DGND
VIN+, VIN– to AGND
Digital Inputs to DGND
Digital Outputs to DGND
AGND to DGND
Input Current to Any Pin Except
Supplies 1
Operating Temperature Range
Storage Temperature Range
Junction Temperature
TSSOP Package
θJA Thermal Impedance
θJC Thermal Impedance
Lead Temperature, Soldering
Vapor Phase (60 sec)
Infrared (15 sec)
ESD
1
Rating
−0.3 V to +3 V
−0.3 V to +3 V
−0.3 V to +0.3 V
−0.3 V to +7 V
−0.3 V to + 0.3 V
−0.3 V to +6 V
−0.3 V to VREF +0.3 V
−0.3 V to VDRIVE + 0.3 V
−0.3 V to VDRIVE + 0.3 V
−0.3 V to +0.3 V
±10 mA
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
−40°C to +105°C
−65°C to +150°C
150°C
150.4°C/W
27.6°C/W
215°C
220°C
1 kV
Transient currents of up to 100 mA do not cause SCR latch-up.
Rev. 0 | Page 8 of 24
AD7767
AVDD 1
16
CS
VREF+
15
SDI
14
MCLK
13
SCLK
12
DRDY
AGND 6
11
DGND
SYNC/PD 7
10
SDO
DVDD 8
9
VDRIVE
2
REFGND 3
VIN+ 4
VIN– 5
AD7767/
AD767-1/
AD7767-2
TOP VIEW
(Not to Scale)
06859-006
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 6. 16-Lead TSSOP Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
1
2
Mnemonic
AVDD
VREF+
3
REFGND
4
5
6
7
VIN+
VIN−
AGND
SYNC/PD
8
9
DVDD
VDRIVE
10
SDO
11
12
DGND
DRDY
13
SCLK
14
15
16
MCLK
SDI
CS
Description
+2.5 V Analog Power Supply.
Reference Input for the AD7767. An external reference must be applied to this input pin. The VREF+ input can range
from 2.4 V to 5 V. The reference voltage input is independent of the voltage magnitude applied to the AVDD pin.
Reference Ground. Ground connection for the reference voltage. The input reference voltage (VREF+) should be
decoupled to this pin.
Positive Input of the Differential Analog Input.
Negative Input of the Differential Analog Input.
Power Supply Ground for Analog Circuitry.
Synchronization and Power-Down Input Pin. This pin has dual functionality. It can be used to synchronize multiple
AD7767 devices and/or put the AD7767 device into power-down mode. See the Power-Down, Reset, and
Synchronization section for further details.
Digital Power Supply Input. This pin can be connected directly to VDRIVE.
Logic Power Supply Input, +1.8 V to +3.6 V. The voltage supplied at this pin determines the operating voltage of
the digital logic interface.
Serial Data Output (SDO). The conversion result from the AD7767 is output on the SDO pin as a 24-bit, twos
complement, MSB first, serial data stream.
Digital Logic Power Supply Ground.
Data Ready Output. A falling edge on the DRDY signal indicates that a new conversion data result is available in the
output register of the AD7767. See the AD7767 Interface section for further details.
Serial Clock Input. The SCLK input provides the serial clock for all serial data transfers with the AD7767 device. See
the AD7767 Interface section for further details.
Master Clock Input. The AD7767 sampling frequency is equal to the MCLK frequency.
Serial Data Input. This is the daisy chain input of the AD7767. See the Daisy Chaining section for further details.
Chip Select Input. The CS input selects the AD7767 device and acts as an enable on the SDO pin. In cases where CS
is used, the MSB of the conversion result is clocked onto the SDO line on the CS falling edge. The CS input allows
multiple AD7767 devices to share the same SDO line. This allows the user to select the appropriate device by
supplying it with a logic low CS signal, which enables the SDO pin of the device concerned. See the AD7767
Interface section for further details.
Rev. 0 | Page 9 of 24
AD7767
TYPICAL PERFORMANCE CHARACTERISTICS
0
–20
–20
–40
–40
–60
–60
–80
–100
–120
–80
–100
–120
–140
–140
–160
–160
–180
0
8k
16k
24k
32k
40k
48k
56k
64k
FREQUENCY (Hz)
–180
0
24k
32k
40k
48k
56k
64k
Figure 10. AD7767 FFT, 1 kHz, −6 dB Input Tone
0
0
–20
–20
–40
AMPLITUDE (dB)
–40
–60
–80
–100
–120
–60
–80
–100
–120
–140
–140
–180
0
4k
8k
12k
16k
20k
24k
28k
32k
FREQUENCY (Hz)
0
06859-102
–180
–20
–20
–40
–40
–60
–60
AMPLITUDE (dB)
0
–80
–100
–120
24k
28k
32k
–120
–160
–180
16k
06859-103
–160
FREQUENCY (Hz)
20k
–100
–140
12k
16k
–80
–140
8k
12k
Figure 11. AD7767-1 FFT, 1 kHz, −6 dB Input Tone
0
4k
8k
FREQUENCY (Hz)
Figure 8. AD7767-1 FFT, 1 kHz, −0.5 dB Input Tone
0
4k
06859-105
–160
–160
Figure 9. AD7767-2 FFT, 1 kHz, −0.5 dB Input Tone
–180
0
4k
8k
12k
FREQUENCY (Hz)
Figure 12. AD7767-2 FFT, 1 kHz, −6 dB Input Tone
Rev. 0 | Page 10 of 24
16k
06859-106
AMPLITUDE (dB)
16k
FREQUENCY (Hz)
Figure 7. AD7767 FFT, 1 kHz, −0.5 dB Input Tone
AMPLITUDE (dB)
8k
06859-104
AMPLITUDE (dB)
0
06859-101
AMPLITUDE (dB)
AVDD = DVDD = 2.5 V ± 5%, VDRIVE = 1.8 V to 3.6 V, VREF = 5 V, MCLK = 1 MHz, common-mode input = VREF/2. TA = 25°C, unless
otherwise noted. All FFTs were generated using 8192 samples using a 4-term Blackman-Harris window.
0
–20
–20
–40
–40
–60
–60
–80
–100
–120
–80
–100
–120
–140
–140
–160
–160
–180
8k
16k
24k
32k
40k
48k
56k
64k
FREQUENCY (Hz)
–180
0
–20
–40
–40
–60
–60
AMPLITUDE (dB)
–20
–80
–100
–120
–160
–180
20k
24k
28k
32k
FREQUENCY (Hz)
56k
64k
TONE A: 24.7kHz
TONE B: 25.3kHz
SECOND-ORDER IMD = –133.33dB
THIRD-ORDER IMD = –108.15dB
–180
0
4k
8k
12k
16k
20k
24k
28k
32k
FREQUENCY (Hz)
Figure 14. AD7767-1 FFT, 1 kHz, −60 dB Input Tone
Figure 17. AD7767-1 IMD FFT, 25 kHz Center Frequency
0
–40
TONE A: 11.7kHz
TONE B: 12.3kHz
–20 SECOND-ORDER IMD = –137.96dB
THIRD-ORDER IMD = –108.1dB
–40
–60
–60
AMPLITUDE (dB)
–20
–80
–100
–120
–80
–100
–120
–140
–160
–160
–180
0
4k
8k
12k
FREQUENCY (Hz)
16k
06859-109
–140
Figure 15. AD7767-2 FFT, 1 kHz, −60 dB Input Tone
–180
0
4k
8k
12k
FREQUENCY (Hz)
Figure 18. AD7767-2 IMD FFT, 12 kHz Center Frequency
Rev. 0 | Page 11 of 24
16k
06859-112
0
AMPLITUDE (dB)
48k
–120
–160
16k
40k
–100
–140
12k
32k
–80
–140
06859-108
AMPLITUDE (dB)
0
8k
24k
Figure 16. AD7767 IMD FFT, 50 kHz Center Frequency
0
4k
16k
FREQUENCY (Hz)
Figure 13. AD7767 FFT, 1 kHz, −60 dB Input Tone
0
8k
06859-111
0
TONE A: 49.7kHz
TONE B: 50.3kHz
SECOND-ORDER IMD = –133.71dB
THIRD-ORDER IMD = –109.05dB
06859-110
AMPLITUDE (dB)
0
06859-107
AMPLITUDE (dB)
AD7767
AD7767
–110
120
–112
115
–114
DYNAMIC RANGE
–116
110
–118
CMRR (dB)
–120
–122
AD7767-1
–124
AD7767
105
OPEN INPUTS
100
–126
95
FULL-SCALE 921Hz
–128
0
100k 200k 300k 400k 500k 600k 700k 800k 900k
1M
FREQUENCY (Hz)
90
06859-113
–130
0
10k
20k
30k
40k
50k
60k
fNOISE (Hz)
06859-116
THD (dB)
AD7767-2
Figure 22. AD7767 CMRR vs. Common-Mode Ripple Frequency
Figure 19. AD7767/AD7767-1/AD7767-2 THD vs. MCLK Frequency
115
200
114
180
MAX = 8388637
MIN = 8388493
SPREAD = 145
AD7767-2
160
113
140
111
OCCURRENCE
AD7767-1
110
120
100
80
60
109
AD7767
40
108
20
1M
FREQUENCY (Hz)
0
CODES
Figure 20. AD7767/AD7767-1/AD7767-2 SNR and THD vs. MCLK Frequency
150
Figure 23. AD7767 24-Bit Histogram
250
AVDD
DVDD
140
MAX = 8388507
MIN = 8388608
SPREAD = 102 CODES
200
OCCURRENCE
130
VDRIVE
120
110
150
100
100
0
10k
20k
30k
fNOISE (Hz)
40k
50k
60k
06859-117
50
0
8388508
8388512
8388516
8388520
8388524
8388528
8388532
8388536
8388540
8388544
8388548
8388552
8388556
8388560
8388564
8388568
8388572
8388576
8388580
8388584
8388588
8388592
8388596
8388600
8388604
8388608
PSRR (dB)
06859-118
100k 200k 300k 400k 500k 600k 700k 800k 900k
8388493
8388497
8388501
8388505
8388509
8388513
8388517
8388521
8388525
8388529
8388533
8388537
8388541
8388545
8388549
8388553
8388557
8388561
8388565
8388569
8388573
8388577
8388581
8388585
8388589
8388593
8388597
8388601
8388605
8388609
8388613
8388617
8388621
8388625
8388629
8388633
8388637
0
06859-114
107
CODES
Figure 21. AD7767 Power Supply Sensitivity vs. Supply Ripple Frequency with
Decoupling Capacitors
Rev. 0 | Page 12 of 24
Figure 24. AD7767-1 24-Bit Histogram
06859-119
SNR (dB)
112
AD7767
LOW TEMPERATURE
NOMINAL TEMPERATURE
HIGH TEMPERATURE
3.04
300
2.28
250
1.52
INL (ppm)
OCCURRENCE
3.80
MAX = 8388593
MIN = 8388526
SPREAD = 69 CODES
350
200
150
0.76
0
–0.76
–1.52
100
–2.28
50
–3.04
0
Figure 25. AD7767-2 24-Bit Histogram
Figure 27. AD7767/AD7767-1/AD7767-2, 24-Bit INL
1.0
0.8
0.6
0.2
0
–0.2
–0.4
–0.6
–0.8
–1.0
4194304
8388608
12582912
16777216
2097152
6291456
10485760
14680064
24-BIT CODES
06859-121
DNL (LSBs)
0.4
0
4194304
8388608
12582912
16777216
2097152
6291456
10485760
14680064
24-BIT CODES
Figure 26. AD7767/AD7767-1/AD7767-2, 24-Bit DNL
Rev. 0 | Page 13 of 24
06859-122
8388592
–3.80
06859-120
CODES
8388589
8388586
8388583
8388580
8388577
8388574
8388571
8388568
8388565
8388562
8388559
8388556
8388553
8388550
8388547
8388544
8388541
8388538
8388535
8388532
8388529
8388526
0
AD7767
TERMINOLOGY
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to the
rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in decibels.
sum of the individual distortion products to the rms amplitude
of the sum of the fundamentals expressed in decibels.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of harmonics to the fundamental. For the AD7767, it is defined as
Differential Nonlinearity (DNL)
DNL is the difference between the measured and the ideal
1 LSB change between any two adjacent codes in the ADC.
THD (dB ) = 20 log
V 22 + V32 + V 42 + V52 + V62
V1
where:
V1 is the rms amplitude of the fundamental.
V2, V3, V4, V5, and V6 are the rms amplitudes of the second to
the sixth harmonics.
Nonharmonic Spurious-Free Dynamic Range (SFDR)
SFDR is the ratio of the rms signal amplitude to the rms value
of the peak spurious spectral component, excluding harmonics.
Dynamic Range
Dynamic range is the ratio of the rms value of the full scale to
the rms noise measured with the inputs shorted together. The
value for the dynamic range is expressed in decibels.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa
and fb, any active device with nonlinearities creates distortion
products at sum and difference frequencies of mfa ± nfb, where
m, n = 0, 1, 2, 3, and so on. Intermodulation distortion terms
are those for which neither m nor n are equal to 0. For example,
the second-order terms include (fa + fb) and (fa − fb), and the
third-order terms include (2fa + fb), (2fa − fb), (fa + 2fb), and
(fa − 2fb).
The AD7767 is tested using the CCIF standard, where two input
frequencies near the top end of the input bandwidth are used.
In this case, the second-order terms are usually distanced in
frequency from the original sine waves, and the third-order
terms are usually at a frequency close to the input frequencies.
As a result, the second- and third-order terms are specified
separately. The calculation of the intermodulation distortion is
as per the THD specification, where it is the ratio of the rms
Integral Nonlinearity (INL)
INL is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function.
Zero Error
Zero error is the difference between the ideal midscale input
voltage (when both inputs are shorted together) and the actual
voltage producing the midscale output code.
Zero Error Drift
Zero error drift is the change in the actual zero error value due
to a temperature change of 1°C. It is expressed as a percentage
of full scale at room temperature.
Gain Error
The first transition (from 100…000 to 100…001) should occur
for an analog voltage ½ LSB above the nominal negative full
scale. The last transition (from 011…110 to 011…111) should
occur for an analog voltage 1½ LSB below the nominal full
scale. The gain error is the deviation of the difference between
the actual level of the last transition and the actual level of the
first transition, from the difference between the ideal levels.
Gain Error Drift
Gain error drift is the change in the actual gain error value due
to a temperature change of 1°C. It is expressed as a percentage
of full scale at room temperature.
Common-Mode Rejection Ratio (CMRR)
CMRR is defined as the ratio of the power in the ADC output
at full-scale frequency f to the power of a 100 mV sine wave
applied to the common-mode voltage of the VIN+ and VIN−
inputs at frequency fs.
CMRR (dB) = 10 log(Pf/Pfs)
where Pf is the power at the frequency f in the ADC output and
Pfs is the power at the frequency fs in the ADC output.
Rev. 0 | Page 14 of 24
AD7767
THEORY OF OPERATION
The AD7767/AD7767-1/AD7767-2 operate using a fully
differential analog input applied to a successive approximation
(SAR) core. The output of the oversampled SAR is filtered using
a linear phase digital FIR filter. The fully filtered data is output
in a serial format, with the MSB being clocked out first.
The digital filtering that follows the converter output acts to
remove the out-of-band quantization noise (see Figure 30). This
also has the effect of reducing the data rate from fMCLK at the
input of the filter to fMCLK/8, fMCLK/16, or fMCLK/32 at the digital
output, depending on which model of the device is being used.
AD7767/AD7767-1/AD7767-2 TRANSFER
FUNCTION
The digital filter consists of three separate filter blocks. Figure 31
shows the three constituent blocks of the filter. The order of
decimation of the first filter block is set as 2, 4, or 8. The
remaining sections both operate in decimate by 2.
24 BITS
TWOS
COMPLEMENT
DIGITAL FILTER
DATA
STREAM
STAGE 1
STAGE 2
STAGE 3
SINC FILTER
FIR FILTER
FIR FILTER
DEC × (2 × n)
DEC × 2
DEC × 2
SDO
24-BIT OUTPUT
011...111
06859-019
The conversion results of the AD7767/AD7767-1/AD7767-2 are
output in a twos complement, 24-bit serial format. The fully
differential inputs VIN+ and VIN− are scaled by the AD7767/
AD7767-1/AD7767-2 relative to the reference voltage input
(VREF+), as shown in Figure 28.
011...110
Figure 31. FIR Filter Stages
(n = 1 for AD7767, n = 2 for AD7767-1, n = 4 for AD7767-2)
000...010
Table 6 shows the three available models of the AD7767, listing
the change in output data rate relative to the order of decimation
rate implemented. This brings into focus the trade-off that
exists between extra filtering and reduction in bandwidth,
whereby using a filter option with a larger decimation rate
increases the noise performance while decreasing the usable
input bandwidth.
000...001
000...000
111...111
111...110
100...001
100...000
Table 6. AD7767 Models
VIN– = VREF – 1LSB
VREF
VIN+ =
2
VREF
VIN– =
2
VIN+ = VREF – 1LSB
VIN– = 0V
06859-012
VIN+ = 0V
Figure 28. AD7767/AD7767-1/AD7767-2 Transfer Function
CONVERTER OPERATION
Internally, the input waveform applied to the SAR core is
converted and an equivalent digital word is output to the digital
filter at a rate equal to MCLK. By employing oversampling, the
quantization noise of the converter is spread across a wide
bandwidth from 0 to fMCLK. This means that the noise energy
contained in the signal band of interest is reduced (see
Figure 29).
BAND OF INTEREST
fMCLK/2
06859-213
QUANTIZATION NOISE
Figure 29. Quantization Noise
Model
AD7767
AD7767-1
AD7767-2
The settling time of the filter implemented on the AD7767,
AD7767-1, and AD7767-2 is related to the length of the filter
employed. The response of the filter in the time domain sets the
filter settling time. Table 7 shows the filter settling times of the
AD7767/AD7767-1/AD7767-2.
The frequency responses of the digital filters on the AD7767,
AD7767-1, and AD7767-2 are shown in Figure 32, Figure 33,
and Figure 34, respectively. At the Nyquist frequency (output
data rate/2), the digital filter provides 6 dB of attenuation. In each
case, the filter provides stop-band attenuation of 100 dB and
pass-band ripple of ±0.005 dB.
06859-214
fMCLK/2
Output Data Rate (ODR)
128 kHz
64 kHz
32 kHz
Note that the output data rates shown in Table 6 are realized
when using the maximum MCLK input frequency of 1.024 MHz.
The output data rate scales linearly with the MCLK frequency,
as does the digital power dissipated in the device.
DIGITAL FILTER CUTOFF FREQUENCY
BAND OF INTEREST
Decimation Rate
8
16
32
Figure 30. Digital Filter Cutoff Frequency
Rev. 0 | Page 15 of 24
AD7767
0
ANALOG INPUT STRUCTURE
The AD7767/AD7767-1/AD7767-2 are configured as a
differential input structure. A true differential signal is sampled
between the analog inputs VIN+ and VIN−, Pin 4 and Pin 5,
respectively. Using differential inputs provides rejection of
signals that are common to both the VIN+ and VIN− pins.
–20
AMPLITUDE (dB)
–40
–60
–80
Figure 35 shows the equivalent analog input circuit of the
AD7767/AD7767-1/AD7767-2. The two diodes on each of the
differential inputs provide ESD protection for the analog inputs.
–100
–120
VREF+
–140
0
16k
32k
48k
64k
80k
96k
112k
128k
FREQUENCY (Hz)
D
06859-216
–160
VIN+
C1
RIN
C2
RIN
C2
D
Figure 32. AD7767 Digital Filter Frequency Response
GND
AGND
VREF+
D
VIN–
–20
C1
D
AMPLITUDE (dB)
–40
GND
–60
Figure 35. Equivalent Analog Input Structure
–80
Take care to ensure that the analog input signal does not exceed
the reference supply voltage VREF+ by more than 0.3 V as specified
in the Absolute Maximum Ratings section. The diodes become
forward biased if the input voltage exceeds this limit and start to
conduct current. The diodes can handle 130 mA maximum.
–100
–120
–160
0
8k
16k
24k
32k
40k
48k
56k
64k
FREQUENCY (Hz)
06859-217
–140
Figure 33. AD7767-1 Digital Filter Frequency Response
0
–20
The impedance of the analog inputs can be modeled as a
parallel combination of C1 and the network formed by the
series connection of RIN, C1, and C2. The value of C1 is
dominated by the pin capacitance. RIN is typically 1.4 kΩ, the
lumped component of serial resistors and the RON of the
switches. C2 is typically 22 pF, and its value is dominated by the
sampling capacitor.
SUPPLY AND REFERENCE VOLTAGES
–40
–60
–80
–100
–120
–140
–160
0
4k
8k
12k
16k
20k
24k
28k
FREQUENCY (Hz)
Figure 34. AD7767-2 Digital Filter Frequency Response
32k
06859-218
AMPLITUDE (dB)
AGND
06859-219
0
The AD7767/AD7767-1/AD7767-2 operate from a 2.5 V supply
applied to the DVDD, AVDD pins. The interface is specified to
operate between 1.7 V and 3.6 V. The AD7767/AD7767-1/
AD7767-2 operate from a 5 V reference applied to the VREF+ pin.
The recommended reference devices are the ADR445 or the
ADR425. The 5 V reference operates both as a reference supply
and as a power supply to the AD7767/AD7767-1/AD7767-2
device. This feature means that the full-scale differential input
range of the AD7767/AD7767-1/AD7767-2 is 10 V. See the
Driving the AD7767 section for details on the maximum input
voltage.
Rev. 0 | Page 16 of 24
AD7767
AD7767 INTERFACE
The AD7767 provides the user with a flexible serial interface,
enabling the user to implement the most desirable interfacing
scheme for their application. The AD7767 interface comprises
seven different signals. Five of these signals are inputs: MCLK,
CS, SYNC/PD, SCLK, and SDI. There are two output signals:
DRDY and SDO.
INITIAL POWER-UP
On initial power-up, apply a continuous MCLK signal. It is
recommended that the user reset the AD7767 to clear the filters
and ensure correct operation. The reset is completed as described
in Figure 5, with all events occurring relative to the rising edge
of MCLK. A negative pulse on the SYNC/PD input initiates the
reset, and the DRDY output switches to logic high and remains
high until valid data is available. Following the power-up of the
AD7767 by transitioning the SYNC/PD pin to logic high, a
settling time is required before valid data is output by the
device. This settling time, tSETTLING, is a function of the MCLK
frequency and the decimation rate. Table 7 lists the settling time
of each of the AD7767 models and should be referenced to
Figure 5.
1
Decimation Rate
8
16
32
There are two distinct patterns that can be initiated to read data
from the AD7767 device; these are for the cases when the CS
falling edge occurs after the DRDY falling edge and for the case
when the CS falling edge occurs before the DRDY falling edge
(when CS is set to logic low).
When the CS falling edge occurs after DRDY falling edge, the
MSB of the conversion result is available on the SDO line on
this CS falling edge. The remaining bits of the conversion result
(MSB-1, MSB-2, and so on) are clocked onto the SDO line by
the falling edges of SCLK that follow the CS falling edge. Figure 3
details this interfacing scheme.
When CS is tied low, the AD7767 serial interface can operate in
3-wire mode as shown in Figure 4. In this case, the MSB of the
conversion result is available on the SDO line on the falling
edge of DRDY. The remaining bits of the data conversion result
(MSB-1, MSB-2, and so on) are clocked onto the SDO line by
the subsequent SCLK falling edges.
POWER-DOWN, RESET, AND SYNCHRONIZATION
Table 7. Filter Settling Time After SYNC/PD
Model
AD7767
AD7767-1
AD7767-2
devices indicating permission to use the bus. When CS is logic
high, the SDO line of the AD7767 is tristated.
1
tSETTLING
594 × (tMCLK + t21)
1186 × (tMCLK + t21)
2370 × (tMCLK + t21)
tSETTLING is measured from the first MCLK rising edge after the rising edge of
SYNC/PD to the falling edge of DRDY.
READING DATA
The AD7767 outputs its data conversion results in an MSB first,
twos complement, 24-bit format on the serial data output pin
(SDO). MCLK is the master clock, which controls all the AD7767
conversions. The SCLK is the serial clock input for the device.
All data transfers take place with respect to the SCLK signal.
The DRDY line is used as a status signal to indicate when the
data is available to be read from the AD7767. The falling edge of
DRDY indicates that a new data-word is available in the output
register of the device. DRDY stays low during the period that
output data is permitted to be read from the SDO pin. The
DRDY signal returns to logic high to indicate when not to read
from the device. Ensure that a data read is not attempted during
this period as the output register is being updated.
The AD7767 SYNC/PD pin allows the user to synchronize
multiple AD7767 devices. This pin also allows the user to reset
and power down the AD7767 device. These features are
implemented relative to the rising edges of MCLK and are
shown in Figure 5.
To power down, reset, or synchronize a device, the AD7767
SYNC/PD pin should be taken low. On the first rising edge of
MCLK, the AD7767 is powered down. The DRDY pin transitions to logic high, indicating that the data in the output register
is no longer valid. The status of the SYNC/PD pin is checked on
each subsequent rising edge of MCLK. On the first rising edge
of MCLK after the SYNC/PD pin is taken high, the AD7767 is
taken out of power-down. On the next rising edge, the filter of
the AD7767 is reset. On the following rising edge, the first new
sample is taken.
A settling time, tSETTLING, from the filter reset, must pass before
valid data is output by the device (as listed in Table 7). The
DRDY output goes logic low after tSETTLING to indicate when
valid data is available on SDO for readback.
The AD7767 offers the user the option of using a chip select
input signal (CS) in its data read cycle. The CS signal is a gate
for the SDO pin and allows many AD7767 devices to share the
same serial bus, acting as an instruction signal to each of these
Rev. 0 | Page 17 of 24
AD7767
DAISY CHAINING
Daisy chaining devices allows numerous devices to use the same
digital interface lines by cascading the outputs of multiple ADCs
on a single data line. This feature is especially useful for reducing component count and wiring connections, for example, in
isolated multiconverter applications or for systems with a limited
interfacing capacity. Data readback is analogous to clocking a
shift register where data is clocked on the falling edge of SCLK.
device in the chain while its DRDY signal is active low. This is
illustrated in the example shown where the conversion results
from devices A, B, C, and D are clocked onto SDO (A) in the
time between the falling edge of DRDY (A) and the rising edge
of DRDY (A).
The block diagram in Figure 36 shows the way in which devices
must be connected in order to achieve daisy chain functionality.
This scheme operates by passing the output data of the SDO pin
of an AD7767 device to the SDI input of the next AD7767 device
in the chain. The data then continues through the chain until it
is clocked onto the SDO pin of the first device on the chain.
As shown in Figure 36, the number of SCLK falling edges that
occur during the period when DRDY (A) is active low must
match the number of devices in the chain multiplied by 24 (the
number of bits that must be clocked through onto SDO (A) for
each device).
READING DATA IN DAISY CHAIN MODE
An example of a daisy chain of four AD7767 devices is shown in
Figure 36 and Figure 37. In the case illustrated in Figure 36, the
output of AD7767 (A) is the output of the full daisy chain. The
last device in the chain (AD7767 (D)) has its serial data in (SDI)
pin connected to ground. All the devices in the chain must use
common MCLK, SCLK, CS, and SYNC/PD signals.
CHOOSING THE SCLK FREQUENCY
The period of SCLK (tSCLK) required for a known daisy chain
length using a known common MCLK frequency must
therefore be established in advance. Note that the maximum
SCLK frequency is governed by t8 and is specified in the Timing
Specifications table for different VDRIVE voltages.
In the case where CS is tied logic low,
⎡ t
⎤
t SCLK ≤ ⎢ READ ⎥
⎣ 24 × K ⎦
To enable the daisy chain conversion process, apply a common
SYNC/PD pulse to all devices, synchronizing all the devices in
the chain (see the Power-Down, Reset, and Synchronization
section).
where:
K is the number of AD7767 devices in the chain.
tSCLK is the period of the SCLK.
After applying a SYNC/PD pulse to all the devices, there is a
delay (as listed in Table 7) before valid conversion data appears
at the output of the chain of devices. As shown in Figure 37,
the first conversion result is output from the device labeled
AD7767 (A). This 24-bit conversion result is followed by the
conversion results from the devices B, C, and D, respectively,
with all conversion results output in an MSB first sequence. The
stream of conversion results is clocked through each device in
the chain and is eventually clocked onto the SDO pin of the
AD7767 (A) device. The conversion results of the all the devices
in the chain must be clocked onto the SDO pin of the final
In the case where CS is used in the daisy chain interface,
(1)
tREAD equals t DRDY − t5.
) − (t 6 + t 7 + t 13 ) ⎤
⎡ (t
t SCLK ≤ ⎢ READ
⎥
24 × K
⎣
⎦
(2)
where:
K is the number of AD7767 devices in the chain.
Note that the maximum value of SCLK is governed by t8 and is
specified in the Timing Specifications table for different VDRIVE
voltages.
Rev. 0 | Page 18 of 24
AD7767
DAISY CHAIN MODE CONFIGURATION AND TIMING DIAGRAMS
SYNC/PD
CS
SYNC/PD
SYNC/PD
CS
CS
AD7767
SDI
AD7767
(D) SDO
SDI
SYNC/PD
SCLK
(C) SDO
SDI
SCLK
MCLK
SYNC/PD
CS
CS
AD7767
(B) SDO
SDI
(A) SDO
SDI
SCLK
MCLK
DRDY
AD7767
SCLK
MCLK
MCLK
06859-013
SCLK
MCLK
Figure 36. AD7767 Daisy Chain Configuration with Four AD7767 Devices
MCLK
1
8×n
DRDY (A)
CS
24 × tSCLK
24 × tSCLK
24 × tSCLK
24 × tSCLK
SCLK
SDO (A)
AD7767 (A)
AD7767 (B)
AD7767 (C)
SDI (A) = SDO (B)
AD7767 (B)
AD7767 (C)
AD7767 (D)
SDI (B) = SDO (C)
AD7767 (C)
AD7767 (D)
SDI (C) = SDO (D)
AD7767 (D)
AD7767 (D)
AD7767 (A)
AD7767 (B)
AD7767 (D)
06859-014
AD7767 (C)
Figure 37. AD7767 Daisy Chain Timing Diagram (n = 1 for AD7767, n = 2 for AD7767-1, n = 4 for AD7767-2) Driving the AD7767
1
MCLK
DRDY (A)
CS
SDO (A)
MSB (A)
LSB (A) MSB (B)
LSB (B) MSB (C)
LSB (C)
LSB (B) MSB (C)
LSB (C) MSB (D)
LSB (D)
t16
SDI (A) = SDO (B)
MSB (B)
t17
Figure 38. AD7767 Daisy Chain SDI Setup and Hold Timing
Rev. 0 | Page 19 of 24
06859-015
SCLK
AD7767
DRIVING THE AD7767
The AD7767 must be driven with fully differential inputs. The
common-mode voltage of the differential inputs to the AD7767
device and thus the limits on the differential inputs are set by
the reference voltage VREF applied to the device. The commonmode voltage of the AD7767 is VREF/2. Where the AD7767 VREF+
pin is supplied with a 5 V supply (the ADR445 or ADR425), the
common mode is at 2.5 V. This means that the maximum inputs
that can be applied on the AD7767 differential inputs are a
5 V p-p input around 2.5 V.
DIFFERENTIAL SIGNAL SOURCE
An example of some recommended driving circuitry that can
be employed in conjunction with the AD7767/AD7767-1/
AD7767-2 is shown in Figure 40. Figure 40 shows how the
ADA4841-1 device can be used to drive an input to the AD7767/
AD7767-1/AD7767-2 from a differential source. Each of the
differential paths is driven by an ADA4841-1 device.
499Ω
3.3nF
VREF
499Ω
AIN+
VREF
2
2.5V
ADA4841-1
VIN+
3.3Ω
1
499Ω
4
VIN+
5
VIN–
AD7767
10nF
0V
3.3nF
VREF
2
VIN–
ADA4841-1
2× VCM
06859-017
SINGLE-ENDED SIGNAL SOURCE
An analog voltage of 2.5 V supplies the AD7767 AVDD pin.
However, the AD7767 allows the user to apply a reference
voltage of up to 5 V. This provides the user with an increased
full-scale range, offering the user the option of using the
AD7767 with a larger LSB voltage size. Figure 39 shows the
maximum and minimum inputs to the AD7767.
In the case where the AD7767 is being supplied from a singleended source, the application circuit in Figure 41 can be used to
drive the AD7767 device. Figure 41 shows how the ADA4941-1
single-to-differential amplifier can be used to create a fully
differential input to the AD7767. The single-ended signal input
is applied to the positive input of the ADA4941-1 device.
Arrange the values of the resistor elements to create a 2.5 V
common-mode input to the AD7767/AD7767-1/AD7767-2
device. R3 and C2 default to 3.3 Ω and 10 nF, respectively.
VSS–
R1
C1
6
5
OUT–
IN
7
V–
2.5V
8
DIS
R1
R3
1
4 VIN+
1
R4
C3
2
3
OUT+
V+
FB
REF
ADA4941-1
R3
AVDD
AD7767
C2
5 VIN–
4
VREF+
2
ADR425
R2
VSS+
R5
2× VCM
R2
RFB
CFB
Figure 41. Driving the AD7767 from a Single-Ended Source
Rev. 0 | Page 20 of 24
06859 -018
VOFFSET
ADR425
Figure 40. Driving the AD7767 from a Fully Differential Source
Figure 39. Maximum Differential Inputs to the AD7767
AIN+
3.3Ω
1kΩ
1kΩ
06859-016
0V
VREF+
499Ω
AIN–
VREF
2
AVDD
AD7767
fMCLK
3.5
DIDD
DIGITAL FILTER
IMAGE AT fMCLK
3.0
2.5
2.0
1.5
AIDD
1.0
fMCLK – (0.547 × ODR)
FIRST ALIAS POINT
IREF
0.5
0
0
Figure 42. AD7767/AD7767-1/AD7767 Spectrum
FREQUENCY (Hz)
Figure 43. AD7767 Current vs. MCLK Frequency
Table 8 shows the attenuation achieved by various orders of
front-end antialias filters prior to the AD7767/AD7767-1/
AD7767-2 at the image of the digital filter stop band, which is
1.024 MHz − 0.547 × ODR.
2.5
2.0
Table 8. Antialias Filter Order Attenuation at First Alias Point
AD7767-1
AD7767-2
Filter Order
1st
2nd
3rd
1st
2nd
3rd
1st
2nd
3rd
DIDD
Attenuation at
1.024 MHz – 0.547 × ODR
27 dB
50 dB
70 dB
33 dB
62 dB
89 dB
38 dB
74 dB
110 dB
CURRENT (mA)
Model
AD7767
100k 200k 300k 400k 500k 600k 700k 800k 900k 1000k
1.5
1.0
AIDD
0.5
IREF
0
0
100k 200k 300k 400k 500k 600k 700k 800k 900k 1000k
FREQUENCY (Hz)
06859-227
BAND OF INTEREST
4.0
06859-231
DIGITAL FILTER 100dB
ANTIALIAS PROTECTION
4.5
06859-226
The AD7767/AD7767-1/AD7767-2 sample the analog input
at a maximum rate of 1.024 MHz. The on-board digital filter
provides up to 100 dB attenuation of any possible aliasing
frequencies in the range from the beginning of the filter stop
band (0.547 × ODR) to where the image of the digital filter pass
band occurs at MCLK − filter stop band (MCLK − 0.547 × ODR),
which is the first alias point. This is illustrated in Figure 42.
in use. For instance, operating the AD7767 device with an
MCLK of 800 kHz gives an output data rate of 100 kHz due to
the decimate by 8 filtering.
CURRENT (mA)
ANTIALIASING
Figure 44. AD7767-1 Current vs. MCLK Frequency
The AD7764 and AD7765 sigma-delta devices are available to
customers that require extra antialias protection. These devices
sample internally at a rate of 20 MHz to achieve up to a maximum of 156 kHz or 312 kHz output data rate. This means that
the first alias point of these devices when run at the maximum
speeds are 19.921 MHz and 19.843 MHz, respectively.
Rev. 0 | Page 21 of 24
1.0
AIDD
0.8
0.6
0.4
IREF
0.2
0
0
100k 200k 300k 400k 500k 600k 700k 800k 900k 1000k
FREQUENCY (Hz)
Figure 45. AD7767-2 Current vs. MCLK Frequency
06859-228
The AD7767/AD7767-1/AD7767-2 offer exceptional performance at ultralow power. Figure 43, Figure 44, and Figure 45
show how the current consumption of the AD7767/AD7767-1/
AD7767-2 scales with the MCLK frequency applied to the
device. Both the digital and analog currents scale as the MCLK
frequency is reduced. The actual throughput of each of the
AD7767/AD7767-1/AD7767-2 equals the MCLK frequency
applied divided by the decimation rate employed by the device
DIDD
1.2
CURRENT (mA)
POWER DISSIPATION
1.4
AD7767
VREF+ INPUT SIGNAL
MULTIPLEXING ANALOG INPUT CHANNELS
The AD7767/AD7767-1/AD7767-2 VREF + pin is supplied with a
5 V input, which is generated by a low noise voltage reference.
Either the ADR445 or the ADR425 can be used with the AD7767/
AD7767-1/AD7767-2 device. This reference voltage input also
acts as a power supply to the AD7767/AD7767-1/AD7767-2
device.
The AD7767/AD7767-1/AD7767-2 can be used with a multiplexer configuration. As per any converter that uses a digital
filtering block, the maximum switching rate, or output data rate
per channel, is a function of the digital filter settling time.
The output of the low noise voltage reference does not require a
buffer; however, it is important to provide a passive filter network
between the VOUT pin of the voltage reference and the VREF+
input on the ADC. Figure 46 shows a reference signal network
that can be used with both the ADR445 and the ADR425.
The 100 nF capacitor on the output of the ADR445 or ADR425
stabilizes the reference output voltage. The series resistor coupled
with the other capacitive values on the reference acts as a lowpass filter. Figure 46 shows the optimal reference voltage input
circuit.
ADR445
OR
ADR425
5V
C39
100nF
100Ω
VREF+
C40
100µF
C15
10µF
C38
100nF
AD7767/
AD7767-1/
AD7767-2
The AD7767 filter settling time equals 74 divided by the output
data rate in use. The maximum switching frequency in a
multiplexed application is therefore 1/(74/ODR), where the
output data rate (ODR) is a function of the applied MCLK
frequency and the decimation rate employed by the device in
question. For example, applying a 1.024 MHz MCLK frequency
to the AD7767 gives a maximum output data rate of 128 kHz,
which in turn allows a 1.729 kHz multiplexer switching rate.
The AD7767-1 and the AD7767-2 employ digital filters with
longer settling time to achieve greater precision; thus, the
maximum switching frequency for these devices is 864 Hz and
432 Hz, respectively.
06859-229
VOUT
A user multiplexing the analog inputs to a converter that
employs a digital filter must wait the full digital filter settling
time before a valid conversion result is achieved; at this point,
the channel can be switched. After switching the channel, the
full settling time must again be observed before a valid conversion result is available and the input is switched once more.
Figure 46. AD7767/AD7767-1/AD7767-2 Reference Filtering,
ADR445 or ADR425 Circuit Topology
For the capacitor designated C40 in Figure 46, either an
electrolytic or tantalum capacitor can be used. This capacitor
acts as a reservoir of charge. Further decoupling capacitors are
placed as close as possible to the VREF+ pin.
Rev. 0 | Page 22 of 24
AD7767
OUTLINE DIMENSIONS
5.10
5.00
4.90
16
9
4.50
4.40
4.30
6.40
BSC
1
8
PIN 1
1.20
MAX
0.15
0.05
0.30
0.19
0.65
BSC
COPLANARITY
0.10
0.20
0.09
SEATING
PLANE
8°
0°
0.75
0.60
0.45
COMPLIANT TO JEDEC STANDARDS MO-153-AB
Figure 47. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD7767BRUZ 1
AD7767BRUZ-RL71
AD7767BRUZ-11
AD7767BRUZ-1-RL71
AD7767BRUZ-21
AD7767BRUZ-2-RL71
EVAL-AD7767EDZ1
EVAL-AD7767-1EDZ1
EVAL-AD7767-2EDZ1
EVAL-CED1Z1
1
Temperature Range
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
Package Description
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
Evaluation Board
Evaluation Board
Evaluation Board
Converter Evaluation and Development Board
Z = RoHS Compliant Part.
Rev. 0 | Page 23 of 24
Package Option
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
AD7767
NOTES
©2007 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06859-0-8/07(0)
Rev. 0 | Page 24 of 24
Similar pages