Ecliptek E13C2D1A-155.520MTR Oscillator Datasheet

Marketing Bulletin
DATE:
May 20, 2003
TO:
Affected Customers
FROM:
Mark Stoner
RE:
Product Termination
To all concerned parties,
This bulletin is to notify all customers of the termination of the following Ecliptek series
effective May 14th, 2003:
Series
E11C1
E13C1
E11C2
E13C2
E31C2
E32C2
Description
Four Pad SMD PECL Oscillator, 5V
Four Pad SMD PECL Oscillator, 3.3V
Six Pad SMD PECL Oscillator, 5V
Six Pad SMD PECL Oscillator, 3.3V
Six Pad SMD PECL VCXO, 5V
Six Pad SMD PECL VCXO, 3.3V
Recommended Replacement
E11J1 or E11W1
E13J1 or E13W1
E11J2 or E11W2
E13J2 or E13W2
E31J2 or E31W2
E32J2 or E32W2
Because of the circumstances surrounding this termination, there will be no end-of-life
policy exercised. The series will be terminated with no purchasing or lifetime buy
window available. All of us at Ecliptek Corporation apologize for any inconvenience this
may have caused and can assure you we are taking measures to insure this will not
happen again in the future.
Best Regards,
Mark W. Stoner
Director of Marketing
Ecliptek Corporation
3545 CADILLAC AVENUE • COSTA MESA, CA 92626-1401 • (714) 433-1200 • Fax (714) 433-1234
E11C1 Series
E11C1
• PECL Output Oscillators
• 5.0V supply voltage
• 4 pad ceramic SMD package with J-leads
• Stability to 20ppm
• Output Enable/Disable available
• Complementary Output available
• Available on Tape and Reel
H 5.1
L 14.2
W 9.85
OSCILLATOR
NOTES
OBSOLETE
__________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
ELECTRICAL SPECIFICATIONS
Frequency Range
19.440MHz to 212.500MHz
Operating Temperature Range
0°C to 70°C or -40°C to 85°C
Storage Temperature Range
-55°C to 125°C
Supply Voltage (VCC)
5.0VDC ±5%
Input Current
100mA Maximum
Logic Type
100KH
Frequency Tolerance / Stability
Inclusive of Operating Temp Range, Supply Voltage,
±100ppm, ±50ppm, ±25ppm, or
Load, and Aging @25°C over 10 years
±20ppm Maximum
Output Voltage Logic High (VOH)
VCC-1.025VDC Minimum
Output Voltage Logic Low (VOL)
VCC-1.620VDC Maximum
Rise Time / Fall Time
20% to 80% of waveform
2 nSeconds Maximum
Duty Cycle
at 50% of waveform
50 ±10(%)
50 ±5(%)
Load Drive Capability
50 Ohms into VCC-2.0VDC
Logic Control / Additional Output
No Connect, Enable/Disable, or
Complementary Output
Enable/Disable Input Voltage
VIL of VCC-1.475VDC Maximum
Enables Output
No Connection
Enables Output
VIH of VCC-1.165VDC Minimum
Disables Output: Logic Low,
Disables Complementary Output: Logic High
Start Up Time
10 mSeconds Maximum
RMS Phase Jitter
FJ = 12kHz to 20MHz
1 pSec Maximum
MANUFACTURER
CATEGORY
SERIES
PACKAGE
VOLTAGE
CLASS
REV.DATE
ECLIPTEK CORP.
OSCILLATOR
E11C1
CERAMIC
5.0V
OS65
10/02
800-ECLIPTEK www.ecliptek.com for latest revision
152
Specifications subject to change without notice.
PART NUMBERING GUIDE
E11C1 F 2 C - 155.520M TR
FREQUENCY TOLERANCE & STABILITY/
OPERATING TEMPERATURE RANGE
C=±100ppm Maximum over 0°C to +70°C
D=±50ppm Maximum over 0°C to +70°C
E=±25ppm Maximum over 0°C to +70°C
F=±20ppm Maximum over 0°C to +70°C
G=±100ppm Maximum over -40°C to +85°C
H=±50ppm Maximum over -40°C to +85°C
AVAILABLE OPTIONS
Blank=Tubes
TR=Tape and Reel (Standard)
FREQUENCY
LOGIC CONTROL/ADDITIONAL OUTPUT
A=No Connect
B=Enable/Disable
C=Complementary Output
DUTY CYCLE
1=50% ±10%, 2=50% ±5%
MECHANICAL DIMENSIONS
SUGGESTED SOLDER PAD LAYOUT
ALL DIMENSIONS IN MILLIMETERS
ALL DIMENSIONS IN MILLIMETERS
Tolerances = ±0.1
Pin 1: Complementary Output, No Connect, or Enable/Disable
Pin 2: Case Ground
Pin 3: Output Pin 4: Supply Voltage
TAPE AND REEL DIMENSIONS
ALL DIMENSIONS IN MILLIMETERS
TAPE
F
12 ±.1
A
B
C
D
E
24 ±.3
11.5 ±.1
10.75 ±.1
4 ±.2
2±.1
F
M
N
O
P
Q
1.5 MIN
50 MIN
20.2 MIN
13±.2
40 MIN
QTY/REEL
1000
REEL
G
H
J
K
L
R
S
T
U
V
B0*
1.5 +.1-0
A0*
.4 ±.05
K0*
2.5 MIN
10 MIN
30.4 MAX
360 MAX
24.4+2-0
*Compliant to EIA 481A
ENVIRONMENTAL/MECHANICAL SPECIFICATIONS
MARKING SPECIFICATIONS
Characteristic
Specification
Line 1: ECLIPTEK
Seal Integrity
Bubble test in Perfluorocarbon at +125°C ±5°C for 60 seconds
minimum (internal crystal only).
Line 2: XX.XXX M
OBSOLETE
Solderability
Sn63 Solder dip at +230°C ±5°C for 5 seconds/95% coverage.
Marking Permanency
10 Strokes with brush after 1 minute soak in solvent, 3 times.
Shock
Random drop on hard wooden plate 3 times from a height
of 20cm.
Vibration
Frequency in MHz (5 Digits Maximum + Decimal)
Line 3: XX Y ZZ
Week of Year
Last Digit of Year
Ecliptek Manufacturing Identifier
Frequency with an amplitude of 1.5mm sweeping between 10Hz
to 55Hz within 1 minute (approximately) for 2 hours minimum on
each axis (X, Y and Z) for a total of 6 hours.
MANUFACTURER
CATEGORY
SERIES
PACKAGE
VOLTAGE
CLASS
REV.DATE
ECLIPTEK CORP.
OSCILLATOR
E11C1
CERAMIC
5.0V
OS65
10/02
800-ECLIPTEK www.ecliptek.com for latest revision
153
Specifications subject to change without notice.
E11C2 Series
E11C2
• PECL Output Oscillators
• 5.0V supply voltage
• 6 pad ceramic SMD package with J-leads
• Stability to 20ppm
• Output Enable/Disable available
• Complementary Output available
• Available on Tape and Reel
NOTES
H 5.1
L 14.2
W 9.85
OSCILLATOR
OBSOLETE
__________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
ELECTRICAL SPECIFICATIONS
Frequency Range
19.440MHz to 212.500MHz
Operating Temperature Range
0°C to 70°C or -40°C to 85°C
Storage Temperature Range
-55°C to 125°C
Supply Voltage (VCC)
5.0VDC ±5%
Input Current
100mA Maximum
Logic Type
100KH
Frequency Tolerance / Stability
Inclusive of Operating Temp Range, Supply Voltage,
±100ppm, ±50ppm, ±25ppm, or
Load, and Aging @25°C over 10 years
±20ppm Maximum
Output Voltage Logic High (VOH)
VCC-1.025VDC Minimum
Output Voltage Logic Low (VOL)
VCC-1.620VDC Maximum
Rise Time / Fall Time
20% to 80% of waveform
2 nSeconds Maximum
Duty Cycle
at 50% of waveform
50 ±10(%)
50 ±5(%)
Load Drive Capability
50 Ohms into VCC-2.0VDC
Logic Control / Additional Output
No Connect, Enable/Disable,
Complementary Output, or
Complementary Output and Enable/Disable
Enable/Disable Input Voltage
VIL of VCC-1.475VDC Maximum
Enables Output
No Connection
Enables Output
VIH of VCC-1.165VDC Minimum
Disables Output: Logic Low
Disables Complementary Output: Logic High
Start Up Time
10 mSeconds Maximum
RMS Phase Jitter
FJ = 12kHz to 20MHz
1 pSec Maximum
MANUFACTURER
CATEGORY
SERIES
PACKAGE
VOLTAGE
CLASS
ECLIPTEK CORP.
OSCILLATOR
E11C2
CERAMIC
5.0V
OS66
800-ECLIPTEK www.ecliptek.com for latest revision
154
REV.DATE
10/02
Specifications subject to change without notice.
PART NUMBERING GUIDE
E11C2 F 2 C - 155.520M TR
FREQUENCY TOLERANCE & STABILITY/
OPERATING TEMPERATURE RANGE
C=±100ppm Maximum over 0°C to +70°C
D=±50ppm Maximum over 0°C to +70°C
E=±25ppm Maximum over 0°C to +70°C
F=±20ppm Maximum over 0°C to +70°C
G=±100ppm Maximum over -40°C to +85°C
H=±50ppm Maximum over -40°C to +85°C
AVAILABLE OPTIONS
Blank=Tubes
TR=Tape and Reel (Standard)
FREQUENCY
LOGIC CONTROL/ADDITIONAL OUTPUT
A=No Connect
D=Complementary Output and Enable/Disable
B=Enable/Disable
E=Complementary Output (Alt. Pin Configuration)
C=Complementary Output G=Complementary Output and Enable/Disable
(Alt. Pin Configuration)
DUTY CYCLE
1=50% ±10%, 2=50% ±5%
MECHANICAL DIMENSIONS
PIN CONNECTIONS TABLE
ALL DIMENSIONS IN MILLIMETERS
TAPE AND REEL DIMENSIONS
ALL DIMENSIONS IN MILLIMETERS
TAPE
F
12 ±.1
A
B
C
D
E
24 ±.3
11.5 ±.1
10.75 ±.1
4 ±.2
2±.1
F
M
N
O
P
Q
1.5 MIN
50 MIN
20.2 MIN
13±.2
40 MIN
QTY/REEL
1000
REEL
G
H
J
K
L
R
S
T
U
V
B0*
1.5 +.1-0
A0*
.4 ±.05
K0*
2.5 MIN
10 MIN
30.4 MAX
360 MAX
24.4+2-0
*Compliant to EIA 481A
ENVIRONMENTAL/MECHANICAL SPECIFICATIONS
Characteristic
MARKING SPECIFICATIONS
Line 1: ECLIPTEK
Specification
OBSOLETE
Seal Integrity
Bubble test in Perfluorocarbon at +125°C ±5°C for 60 seconds
minimum (internal crystal only).
Solderability
Sn63 Solder dip at +230°C ±5°C for 5 seconds/95% coverage.
Marking Permanency
10 Strokes with brush after 1 minute soak in solvent, 3 times.
Shock
Random drop on hard wooden plate 3 times from a height
of 20cm.
Vibration
Frequency with an amplitude of 1.5mm sweeping between 10Hz
to 55Hz within 1 minute (approximately) for 2 hours minimum on
each axis (X, Y and Z) for a total of 6 hours.
MANUFACTURER
CATEGORY
SERIES
ECLIPTEK CORP.
OSCILLATOR
E11C2
800-ECLIPTEK www.ecliptek.com for latest revision
Line 2: XX.XXX M
Frequency in MHz (5 Digits Maximum + Decimal)
Line 3: XX Y ZZ
PACKAGE
CERAMIC
155
Week of Year
Last Digit of Year
Ecliptek Manufacturing Identifier
VOLTAGE
CLASS
REV.DATE
5.0V
OS66
10/02
Specifications subject to change without notice.
E13C1 Series
E13C1
• PECL Output Oscillators
• 3.3V supply voltage
• 4 pad ceramic SMD package with J-leads
• Stability to 20ppm
• Output Enable/Disable available
• Complementary Output available
• Available on Tape and Reel
H 5.1
L 14.2
W 9.85
OSCILLATOR
NOTES
__________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
OBSOLETE
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
ELECTRICAL SPECIFICATIONS
Frequency Range
19.440MHz to 212.500MHz
Operating Temperature Range
0°C to 70°C or -40°C to 85°C
Storage Temperature Range
-55°C to 125°C
Supply Voltage (VCC)
3.3VDC ±5%
Input Current
75mA Maximum
Logic Type
100KH
Frequency Tolerance / Stability
Inclusive of Operating Temp Range, Supply Voltage,
±100ppm, ±50ppm, ±25ppm, or
Load, and Aging @25°C over 10 years
±20ppm Maximum
Output Voltage Logic High (VOH)
VCC-1.025VDC Minimum
Output Voltage Logic Low (VOL)
VCC-1.620VDC Maximum
Rise Time / Fall Time
20% to 80% of waveform
2 nSeconds Maximum
Duty Cycle
at 50% of waveform
50 ±10(%)
50 ±5(%)
Load Drive Capability
50 Ohms into VCC-2.0VDC
Logic Control / Additional Output
No Connect, Enable/Disable, or
Complementary Output
Enable/Disable Input Voltage
VIL of VCC-1.475VDC Maximum
Enables Output
No Connection
Enables Output
VIH of VCC-1.165VDC Minimum
Disable Output: Logic Low
Disables Complementary Output: Logic High
Start Up Time
10 mSeconds Maximum
RMS Phase Jitter
FJ = 12kHz to 20MHz
1 pSec Maximum
MANUFACTURER
CATEGORY
SERIES
PACKAGE
VOLTAGE
CLASS
REV.DATE
ECLIPTEK CORP.
OSCILLATOR
E13C1
CERAMIC
3.3V
OS63
10/02
800-ECLIPTEK www.ecliptek.com for latest revision
156
Specifications subject to change without notice.
PART NUMBERING GUIDE
E13C1 F 2 C - 155.520M TR
FREQUENCY TOLERANCE & STABILITY/
OPERATING TEMPERATURE RANGE
C=±100ppm Maximum over 0°C to +70°C
D=±50ppm Maximum over 0°C to +70°C
E=±25ppm Maximum over 0°C to +70°C
F=±20ppm Maximum over 0°C to +70°C
G=±100ppm Maximum over -40°C to +85°C
H=±50ppm Maximum over -40°C to +85°C
AVAILABLE OPTIONS
Blank=Tubes
TR=Tape and Reel (Standard)
FREQUENCY
LOGIC CONTROL/ADDITIONAL OUTPUT
A=No Connect
B=Enable/Disable
C=Complementary Output
DUTY CYCLE
1=50% ±10%, 2=50% ±5%
MECHANICAL DIMENSIONS
SUGGESTED SOLDER PAD LAYOUT
ALL DIMENSIONS IN MILLIMETERS
ALL DIMENSIONS IN MILLIMETERS
Tolerances = ±0.1
Pin 1: Complementary Output, No Connect, or Enable/Disable
Pin 2: Case Ground
Pin 3: Output Pin 4: Supply Voltage
TAPE AND REEL DIMENSIONS
ALL DIMENSIONS IN MILLIMETERS
TAPE
F
12 ±.1
A
B
C
D
E
24 ±.3
11.5 ±.1
10.75 ±.1
4 ±.2
2±.1
F
M
N
O
P
Q
1.5 MIN
50 MIN
20.2 MIN
13±.2
40 MIN
QTY/REEL
1000
REEL
G
H
J
K
L
R
S
T
U
V
B0*
1.5 +.1-0
A0*
.4 ±.05
K0*
2.5 MIN
10 MIN
30.4 MAX
360 MAX
24.4+2-0
*Compliant to EIA 481A
ENVIRONMENTAL/MECHANICAL SPECIFICATIONS
MARKING SPECIFICATIONS
Characteristic
Specification
Line 1: ECLIPTEK
Seal Integrity
Bubble test in Perfluorocarbon at +125°C ±5°C for 60 seconds
minimum (internal crystal only).
Line 2: XX.XXX M
Solderability
Sn63 Solder dip at +230°C ±5°C for 5 seconds/95% coverage.
Marking Permanency
10 Strokes with brush after 1 minute soak in solvent, 3 times.
Shock
Random drop on hard wooden plate 3 times from a height
of 20cm.
Vibration
Frequency with an amplitude of 1.5mm sweeping between 10Hz
to 55Hz within 1 minute (approximately) for 2 hours minimum on
each axis (X, Y and Z) for a total of 6 hours.
OBSOLETE
Frequency in MHz (5 Digits Maximum + Decimal)
Line 3: XX Y ZZ
Week of Year
Last Digit of Year
Ecliptek Manufacturing Identifier
MANUFACTURER
CATEGORY
SERIES
PACKAGE
VOLTAGE
CLASS
REV.DATE
ECLIPTEK CORP.
OSCILLATOR
E13C1
CERAMIC
3.3V
OS63
10/02
800-ECLIPTEK www.ecliptek.com for latest revision
157
Specifications subject to change without notice.
E13C2 Series
E13C2
• PECL Output Oscillators
• 3.3V supply voltage
• 6 pad ceramic SMD package with J-leads
• Stability to 20ppm
• Output Enable/Disable available
• Complementary Output available
• Available on Tape and Reel
H 5.1
L 14.2
W 9.85
OSCILLATOR
NOTES
OBSOLETE
__________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
ELECTRICAL SPECIFICATIONS
Frequency Range
19.440MHz to 212.500MHz
Operating Temperature Range
0°C to 70°C or -40°C to 85°C
Storage Temperature Range
-55°C to 125°C
Supply Voltage (VCC)
3.3VDC ±5%
Input Current
75mA Maximum
Logic Type
100KH
Frequency Tolerance / Stability
Inclusive of Operating Temp Range, Supply Voltage,
±100ppm, ±50ppm, ±25ppm, or
Load, and Aging @25°C over 10 years
±20ppm Maximum
Output Voltage Logic High (VOH)
VCC-1.025VDC Minimum
Output Voltage Logic Low (VOL)
VCC-1.620VDC Maximum
Rise Time / Fall Time
20% to 80% of waveform
2 nSeconds Maximum
Duty Cycle
at 50% of waveform
50 ±10(%)
50 ±5(%)
Load Drive Capability
50 Ohms into VCC-2.0VDC
Logic Control / Additional Output
No Connect, Enable/Disable,
Complementary Output, or
Complementary Output and Enable/Disable
Enable/Disable Input Voltage
VIL of VCC-1.475VDC Maximum
Enables Output
No Connection
Enables Output
VIH of VCC-1.165VDC Minimum
Disables Output: Logic Low
Disables Complementary Output: Logic High
Start Up Time
10 mSeconds Maximum
RMS Phase Jitter
FJ = 12kHz to 20MHz
1 pSec Maximum
MANUFACTURER
CATEGORY
SERIES
PACKAGE
VOLTAGE
CLASS
REV.DATE
ECLIPTEK CORP.
OSCILLATOR
E13C2
CERAMIC
3.3V
OS64
10/02
800-ECLIPTEK www.ecliptek.com for latest revision
158
Specifications subject to change without notice.
PART NUMBERING GUIDE
E13C2 F 2 C - 155.520M TR
FREQUENCY TOLERANCE & STABILITY/
OPERATING TEMPERATURE RANGE
C=±100ppm Maximum over 0°C to +70°C
D=±50ppm Maximum over 0°C to +70°C
E=±25ppm Maximum over 0°C to +70°C
F=±20ppm Maximum over 0°C to +70°C
G=±100ppm Maximum over -40°C to +85°C
H=±50ppm Maximum over -40°C to +85°C
AVAILABLE OPTIONS
Blank=Tubes
TR=Tape and Reel (Standard)
FREQUENCY
LOGIC CONTROL/ADDITIONAL OUTPUT
A=No Connect
D=Complementary Output and Enable/Disable
B=Enable/Disable
E=Complementary Output (Alt. Pin Configuration)
C=Complementary Output G=Complementary Output and Enable/Disable
(Alt. Pin Configuration)
DUTY CYCLE
1=50% ±10%, 2=50% ±5%
MECHANICAL DIMENSIONS
PIN CONNECTIONS TABLE
ALL DIMENSIONS IN MILLIMETERS
SUGGESTED
SOLDER PAD
LAYOUT
TAPE AND REEL DIMENSIONS
ALL DIMENSIONS IN MILLIMETERS
TAPE
F
12 ±.1
A
B
C
D
E
24 ±.3
11.5 ±.1
10.75 ±.1
4 ±.2
2±.1
F
M
N
O
P
Q
1.5 MIN
50 MIN
20.2 MIN
13±.2
40 MIN
QTY/REEL
1000
REEL
G
H
J
K
L
R
S
T
U
V
B0*
1.5 +.1-0
A0*
.4 ±.05
K0*
2.5 MIN
10 MIN
30.4 MAX
360 MAX
24.4+2-0
*Compliant to EIA 481A
ENVIRONMENTAL/MECHANICAL SPECIFICATIONS
Characteristic
MARKING SPECIFICATIONS
Line 1: ECLIPTEK
Specification
OBSOLETE
Seal Integrity
Bubble test in Perfluorocarbon at +125°C ±5°C for 60 seconds
minimum (internal crystal only).
Solderability
Sn63 Solder dip at +230°C ±5°C for 5 seconds/95% coverage.
Marking Permanency
10 Strokes with brush after 1 minute soak in solvent, 3 times.
Shock
Random drop on hard wooden plate 3 times from a height
of 20cm.
Vibration
Frequency with an amplitude of 1.5mm sweeping between 10Hz
to 55Hz within 1 minute (approximately) for 2 hours minimum on
each axis (X, Y and Z) for a total of 6 hours.
Line 2: XX.XXX M
Frequency in MHz (5 Digits Maximum + Decimal)
Line 3: XX Y ZZ
Week of Year
Last Digit of Year
Ecliptek Manufacturing Identifier
MANUFACTURER
CATEGORY
SERIES
PACKAGE
VOLTAGE
CLASS
REV.DATE
ECLIPTEK CORP.
OSCILLATOR
E13C2
CERAMIC
3.3V
OS64
10/02
800-ECLIPTEK www.ecliptek.com for latest revision
159
Specifications subject to change without notice.
E31C2 Series
E31C2
• PECL Output VCXO
• 5.0V supply voltage
• 6 pad ceramic SMD package with J-leads
• Stability to 20ppm
• Output Enable/Disable available
• Complementary Output available
• Available on Tape and Reel
H 5.1
L 14.2
W 9.85
OSCILLATOR
ELECTRICAL SPECIFICATIONS
Frequency Range
19.440MHz to 83.333MHz
Operating Temperature Range
0°C to 70°C or -40°C to 85°C
Storage Temperature Range
Supply Voltage (VCC)
Input Current
OBSOLETE
Logic Type
-55°C to 125°C
5.0VDC ±5%
100mA Maximum
100KH
Frequency Tolerance / Stability
Inclusive of Operating Temp Range, Supply Voltage, ±50ppm, ±25ppm, or
Load, and Aging @25°C over 10 years
±20ppm Maximum
Output Voltage Logic High (VOH)
VCC-1.025VDC Minimum
Output Voltage Logic Low (VOL)
VCC-1.620VDC Maximum
Rise Time / Fall Time
20% to 80% of waveform
2 nSeconds Maximum
Duty Cycle
at 50% of waveform
50 ±10(%)
50 ±5(%)
Load Drive Capability
50 Ohms into VCC-2.0VDC
Additional Output / Logic Control
No Connect and Single Output
Enable/Disable and Single Output
No Connect and Complementary Output or
Enable/Disable and Complementary Output
Enable/Disable Input Voltage
VIL of VCC-1.475VDC Maximum
Enables Output
No Connection
Enables Output
VIH of VCC-1.165VDC Minimum
Disables Output: Logic Low
Disables Complementary Output: Logic High
Start Up Time
10 mSeconds Maximum
RMS Phase Jitter
FJ = 12kHz to 20MHz
Absolute Pull Range (APR)
Inclusive of Operating Temp Range, Supply Voltage, ±50ppm Minimum
1 pSec Maximum
Load, and Aging @25°C over 10 years
Linearity
20%, 15%, or 10% Maximum
Control Voltage (VC): Test Conditions for APR
2.5VDC ±2.0VDC
Control Voltage Range (VCR)
0.0VDC to VCC
Center Control Voltage
2.5VDC
Transfer Function
Positive Transfer Characteristic
Input Impedance
50kOhms Typical
Modulation Bandwidth
10kHz Minimum
at -3dB with Control Voltage of +2.5VDC
MANUFACTURER
CATEGORY
SERIES
PACKAGE
VOLTAGE
CLASS
REV.DATE
ECLIPTEK CORP.
OSCILLATOR
E31C2
CERAMIC
5.0V
OS68
10/02
800-ECLIPTEK www.ecliptek.com for latest revision
188
Specifications subject to change without notice.
PART NUMBERING GUIDE
E31C2 F 3 A 2 C - 77.760M TR
FREQUENCY TOLERANCE & STABILITY/
OPERATING TEMPERATURE RANGE
D=±50ppm Maximum over 0°C to +70°C
E=±25ppm Maximum over 0°C to +70°C
F=±20ppm Maximum over 0°C to +70°C
H=±50ppm Maximum over -40°C to +85°C
AVAILABLE OPTIONS
Blank=Tubes
TR = Tape and Reel (Standard)
FREQUENCY
ADDITIONAL OUTPUT/LOGIC CONTROL
A=No Connect and Single Output
B=Enable/Disable and Single Output
C=No Connect and Complementary Output
D=Enable/Disable and Complementary Output
APR
3=±50ppm Minimum
LINEARITY
A=20%
B=15%
C=10%
DUTY CYCLE
1=50 ±10(%), 2=50 ±5(%)
MECHANICAL DIMENSIONS
SUGGESTED SOLDER PAD LAYOUT
ALL DIMENSIONS IN MILLIMETERS
ALL DIMENSIONS IN MILLIMETERS
Pin 1: Voltage Control
Pin 2: Enable/Disable or No Connect
Pin 3: Case Ground
TAPE AND REEL DIMENSIONS
Pin 4: Output
Pin 5: Complementary Output or No Connect
Pin 6: Supply Voltage
Tolerances = ±0.1
ALL DIMENSIONS IN MILLIMETERS
TAPE
F
12 ±.1
A
B
C
D
E
24 ±.3
11.5 ±.1
10.75 ±.1
4 ±.2
2±.1
F
M
N
O
P
Q
1.5 MIN
50 MIN
20.2 MIN
13±.2
40 MIN
QTY/REEL
1000
REEL
G
H
J
K
L
R
S
T
U
V
B0*
1.5 +.1-0
A0*
.4 ±.05
K0*
2.5 MIN
10 MIN
30.4 MAX
360 MAX
24.4+2-0
*Compliant to EIA 481A
ENVIRONMENTAL/MECHANICAL SPECIFICATIONS
MARKING SPECIFICATIONS
Characteristic
Specification
Line 1: ECLIPTEK
Seal Integrity
Bubble test in Perfluorocarbon at +125°C ±5°C for 60 seconds
minimum (internal crystal only).
Line 2: XX.XXX M
Solderability
Sn63 Solder dip at +230°C ±5°C for 5 seconds/95% coverage.
Marking Permanency
10 Strokes with brush after 1 minute soak in solvent, 3 times.
Shock
Random drop on hard wooden plate 3 times from a height
of 20cm.
Vibration
Frequency with an amplitude of 1.5mm sweeping between 10Hz
to 55Hz within 1 minute (approximately) for 2 hours minimum on
each axis (X, Y and Z) for a total of 6 hours.
OBSOLETE
Frequency in MHz (5 Digits Maximum + Decimal)
Line 3: XX Y ZZ
Week of Year
Last Digit of Year
Ecliptek Manufacturing Identifier
MANUFACTURER
CATEGORY
SERIES
PACKAGE
VOLTAGE
CLASS
REV.DATE
ECLIPTEK CORP.
OSCILLATOR
E31C2
CERAMIC
5.0V
OS68
10/02
800-ECLIPTEK www.ecliptek.com for latest revision
189
Specifications subject to change without notice.
E32C2 Series
E32C2
• PECL Output VCXO
• 3.3V supply voltage
• 6 pad ceramic SMD package with J-leads
• Stability to 20ppm
• Output Enable/Disable available
• Complementary Output available
• Available on Tape and Reel
H 5.1
L 14.2
W 9.85
OSCILLATOR
ELECTRICAL SPECIFICATIONS
Frequency Range
19.440MHz to 83.333MHz
Operating Temperature Range
Storage Temperature Range
Supply Voltage (VCC)
Input Current
OBSOLETE
Logic Type
0°C to 70°C or -40°C to 85°C
-55°C to 125°C
3.3VDC ±5%
75mA Maximum
100KH
Frequency Tolerance / Stability
Inclusive of Operating Temp Range, Supply Voltage, ±50ppm, ±25ppm, or
Load, and Aging @25°C over 10 years
±20ppm Maximum
Output Voltage Logic High (VOH)
VCC-1.025VDC Minimum
Output Voltage Logic Low (VOL)
VCC-1.620VDC Maximum
Rise Time / Fall Time
20% to 80% of waveform
2 nSeconds Maximum
Duty Cycle
at 50% of waveform
50 ±10(%)
50 ±5(%)
Load Drive Capability
50 Ohms into VCC-2.0VDC
Additional Output / Logic Control
No Connect and Single Output
Enable/Disable and Single Output
No Connect and Complementary Output or
Enable/Disable and Complementary Output
Enable/Disable Input Voltage
VIL of VCC-1.475VDC Maximum
Enables Output
No Connection
Enables Output
VIH of VCC-1.165VDC Minimum
Disables Output: Logic Low
Disables Complementary Output: Logic High
Start Up Time
10 mSeconds Maximum
RMS Phase Jitter
FJ = 12kHz to 20MHz
Absolute Pull Range (APR)
Inclusive of Operating Temp Range, Supply Voltage, ±50ppm Minimum
1 pSec Maximum
Load, and Aging @25°C over 10 years
Linearity
20%, 15%, or 10% Maximum
Control Voltage (VC): Test Conditions for APR
1.65VDC ±1.35VDC
Control Voltage Range (VCR)
0.0VDC to VCC
Center Control Voltage
1.65VDC
Transfer Function
Positive Transfer Characteristic
Input Impedance
50kOhms Typical
Modulation Bandwidth
10kHz Minimum
at -3dB with Control Voltage of +1.65VDC
MANUFACTURER
CATEGORY
SERIES
PACKAGE
VOLTAGE
CLASS
REV.DATE
ECLIPTEK CORP.
OSCILLATOR
E32C2
CERAMIC
3.3V
OS67
10/02
800-ECLIPTEK www.ecliptek.com for latest revision
190
Specifications subject to change without notice.
PART NUMBERING GUIDE
E32C2 F 3 A 2 C - 77.760M TR
FREQUENCY TOLERANCE & STABILITY/
OPERATING TEMPERATURE RANGE
D=±50ppm Maximum over 0°C to +70°C
E=±25ppm Maximum over 0°C to +70°C
F=±20ppm Maximum over 0°C to +70°C
H=±50ppm Maximum over -40°C to +85°C
AVAILABLE OPTIONS
Blank=Tubes
TR = Tape and Reel (Standard)
FREQUENCY
ADDITIONAL OUTPUT/LOGIC CONTROL
A=No Connect and Single Output
B=Enable/Disable and Single Output
C=No Connect and Complementary Output
D=Enable/Disable and Complementary Output
APR
3=±50ppm Minimum
LINEARITY
A=20%
B=15%
C=10%
DUTY CYCLE
1=50 ±10(%), 2=50 ±5(%)
MECHANICAL DIMENSIONS
SUGGESTED SOLDER PAD LAYOUT
ALL DIMENSIONS IN MILLIMETERS
ALL DIMENSIONS IN MILLIMETERS
Pin 1: Voltage Control
Pin 2: Enable/Disable or No Connect
Pin 3: Case Ground
TAPE AND REEL DIMENSIONS
Pin 4: Output
Pin 5: Complementary Output or No Connect
Pin 6: Supply Voltage
Tolerances = ±0.1
ALL DIMENSIONS IN MILLIMETERS
TAPE
F
12 ±.1
A
B
C
D
E
24 ±.3
11.5 ±.1
10.75 ±.1
4 ±.2
2±.1
F
M
N
O
P
Q
1.5 MIN
50 MIN
20.2 MIN
13±.2
40 MIN
QTY/REEL
1000
REEL
G
H
J
K
L
R
S
T
U
V
B0*
1.5 +.1-0
A0*
.4 ±.05
K0*
2.5 MIN
10 MIN
30.4 MAX
360 MAX
24.4+2-0
*Compliant to EIA 481A
ENVIRONMENTAL/MECHANICAL SPECIFICATIONS
Characteristic
MARKING SPECIFICATIONS
Line 1: ECLIPTEK
Specification
OBSOLETE
Seal Integrity
Bubble test in Perfluorocarbon at +125°C ±5°C for 60 seconds
minimum (internal crystal only).
Solderability
Sn63 Solder dip at +230°C ±5°C for 5 seconds/95% coverage.
Marking Permanency
10 Strokes with brush after 1 minute soak in solvent, 3 times.
Shock
Random drop on hard wooden plate 3 times from a height
of 20cm.
Vibration
Frequency with an amplitude of 1.5mm sweeping between 10Hz
to 55Hz within 1 minute (approximately) for 2 hours minimum on
each axis (X, Y and Z) for a total of 6 hours.
Line 2: XX.XXX M
Frequency in MHz (5 Digits Maximum + Decimal)
Line 3: XX Y ZZ
Week of Year
Last Digit of Year
Ecliptek Manufacturing Identifier
MANUFACTURER
CATEGORY
SERIES
PACKAGE
VOLTAGE
CLASS
REV.DATE
ECLIPTEK CORP.
OSCILLATOR
E32C2
CERAMIC
3.3V
OS67
10/02
800-ECLIPTEK www.ecliptek.com for latest revision
191
Specifications subject to change without notice.
Similar pages