AD AD8018 5 v, rail-to-rail, high-output current, xdsl line drive amplifier Datasheet

a
5 V, Rail-to-Rail, High-Output Current,
xDSL Line Drive Amplifier
AD8018
FEATURES
Ideal xDSL Line Drive Amplifier for USB, PCMCIA, or
PCI-Based Customer Premise Equipment (CPE). The
AD8018 provides maximum reach on 5 V supply,
driving 16 dBm of power into a back-terminated,
transformer-coupled 100 ⍀ while maintaining –82 dBc
of out-of-band SFDR.
Rail-to-Rail Output Voltage and High Output Current
Drive
400 mA Output Current into Differential Load of 10 ⍀
@ 8 V p-p
Low Single-Tone Distortion
–86 dBc Worst Harmonic, 6 V p-p into Differential 10 ⍀
@ 100 kHz
Low Noise
4.5 nV/√Hz Voltage Noise Density, 100 kHz
Out-of-Band SFDR = –82 dBc, 144 kHz to 500 kHz,
R LOAD = 12.5 ⍀, PLINE = 13 dBm
Low-Power Operation
3.3 V to 8 V Power Supply Range
Two Logic Bits for Standby and Shutdown
Low Supply Current of 9 mA/Amplifier (Typ)
Current Feedback Amplifiers
High Speed
130 MHz Bandwidth (–3 dB)
300 V/␮s Slew Rate
APPLICATIONS
xDSL USB, PCI, PCMCIA Cards
Consumer DSL Modems
Twisted Pair Line Driver
–30
N = 4.0
–40
VS = 5V
SFDR – dBc
–50
PIN CONFIGURATIONS
8-Lead SOIC
(Thermal Coastline)
OUT1 1
AD8018AR
–IN1 2
14-Lead TSSOP
8 ⴙVS
ⴙIN1 3
6 –IN2
–VS 4
5 ⴙIN2
13 ⴙVS
OUT1 2
7 OUT2
–IN1 3
12 OUT2
ⴙIN1 4
11 –IN2
–VS 5
10 ⴙIN2
9 PWDN0
PWDN1 6
8 DGND
NC 7
NC = NO CONNECT
PRODUCT DESCRIPTION
The AD8018 is intended for use in single-supply (5 V) xDSL
modems where high-output current and low distortion are
essential to achieve maximum reach. The dual high-speed
amplifiers are capable of driving low distortion signals to within
0.5 V of the power supply rail. Each amplifier can drive 400 mA
of current into 10 Ω (differential) while maintaining –82 dBc
out-of-band SFDR. The AD8018 is available with flexible standby
and shutdown modes. Two digital logic bits (PWDN1 and
PWDN0) may be used to put the AD8018 into one of three
modes: full power, standby (outputs low impedance), and
shutdown (outputs high impedance).
Fabricated with ADI’s high-speed XFCB (eXtra Fast Complementary Bipolar) process, the high bandwidth and fast slew rate
of the AD8018 keep distortion to a minimum, while dissipating a minimum of power. The quiescent current of the AD8018
is a low 9 mA/amplifier. The AD8018 drive capability comes in
compact 8-lead Thermal Coastline SOIC and 14-lead TSSOP
packages. Low-distortion, rail-to-rail output voltage, and highcurrent drive in small packages make the AD8018 ideal for use in
low-cost USB, PCMCIA, and PCI Customer Premise Equipment
for ADSL, SDSL, VDSL, and proprietary xDSL systems. Both
models will operate over the temperature range –40°C to +85°C.
VS = 3.3V
5V
0.01␮F
–60
100⍀
1nF
10⍀
VS = 8V
10k⍀
10k⍀
–70
VIN
VREF
0.01␮F
–80
750⍀
6
8
10
12
PLINE – dBm
14
16
18
Figure 1. Out-of-Band SFDR vs. ADSL Upstream Line Power;
VS = 5 V, N = 4 Turns, 144 kHz to 500 kHz. See Evaluation
Board Schematics in Figure 11.
0.01␮F
100⍀
R1
3.1⍀
RL = 100⍀
POUT
16dBm
750⍀
750⍀
LINEPOWER
13dBm
R2
3.1⍀
10k⍀
–90
4
AD8018ARU 14
NC
NC 1
10⍀
1nF
10k⍀
1:4
TRANSFORMER
Figure 2. Single-Supply Voltage Differential Drive Circuit
for xDSL Applications
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2000
AD8018–SPECIFICATIONS (@ 25ⴗC, V = 5 V, R = 100 ⍀, R = R = 750 ⍀ unless otherwise noted.)
S
Parameter
DYNAMIC PERFORMANCE
–3 dB Bandwidth
0.1 dB Bandwidth
Large Signal Bandwidth
Slew Rate
Rise and Fall Time
Settling Time
NOISE/HARMONIC
PERFORMANCE
Distortion,
Second Harmonic
Third Harmonic
MTPR (In-Band)
SFDR (Out-of-Band)
Input Noise Voltage
Input Noise Current
Crosstalk
L
F
G
Conditions
Min
Typ
G = 1, VOUT < 0.4 V p-p, RL = 5 Ω
G = 1, VOUT < 0.4 V p-p, RL = 100 Ω
G = 2, VOUT < 0.4 V p-p, RL = 5 Ω
G = 2, VOUT < 0.4 V p-p, RL = 100 Ω
VOUT < 0.4 V p-p, RL = 100 Ω
VOUT = 4 V p-p, G = +2
Noninverting, VOUT = 4 V p-p
Noninverting, VOUT = 2 V p-p
0.1%, VOUT = 2 V p-p, RL = 100 Ω
40
100
35
80
50
130
40
100
10
80
300
5.5
25
MHz
MHz
MHz
MHz
MHz
MHz
V/␮s
ns
ns
–89
–61
–86
–74
–94
–63
–89
–77
–70
–82
4.5
1
10
–74
dBc
dBc
dBc
dBc
dBc
dBc
nV√Hz
pA√Hz
pA√Hz
dB
VOUT = 6 V p-p (Differential)
100 kHz, RL = 10 Ω
500 kHz, RL = 10 Ω
100 kHz, RL = 10 Ω
500 kHz, RL = 10 Ω
25 kHz to 138 kHz, RL = 12.5 Ω, PLINE = +13 dBm
144 kHz to 500 kHz, RL = 12.5 Ω, PLINE = +13 dBm
f = 100 kHz
f = 100 kHz (+Inputs)
f = 100 kHz (–Inputs)
f = 1 MHz, G = +2
DC PERFORMANCE
Input Offset Voltage
1
TMIN to TMAX
Input Offset Voltage Match
Transimpedance
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Bias Current (–)
VOUT = 2 V p-p, RL = 5 Ω
TMIN to TMAX
830
700
+Input
–Input
+Input
0.1
2000
10
125
1
0.3
TMIN to TMAX
Input Bias Current (–) Match
0.1
TMIN to TMAX
Input Bias Current (+)
1
TMIN to TMAX
Input Bias Current (+) Match
CMRR
Input CM Voltage Range
OUTPUT CHARACTERISTICS
Cap Load
Output Resistance
Output Voltage Swing
Linear Output Current
Short-Circuit Current
POWER SUPPLY
Supply Current/Amp
STBY Supply Current/Amp
SHUTDOWN Supply Current/Amp
Operating Range
+Power Supply Rejection Ratio
–Power Supply Rejection Ratio
0.1
TMIN to TMAX
VIN 2 V to 4 V
51
1.2
30% Overshoot
Frequency = 100 kHz, PWDN1, PWDN0 = 1
RL = 100 Ω
RL = 5 Ω
SFDR < –85 dBc, f = 100 kHz, RL = 10 Ω, Differential
PWDN1 = 1, PWDN0 = 1
TMIN to TMAX
PWDN1 = 0, PWDN0 = 1 or
PWDN1 = 1, PWDN0 = 0
PWDN1 = 0, PWDN0 = 0
Single Supply
⌬VS = ⫾1 V
TMIN to TMAX
⌬VS = ⫾1 V
TMIN to TMAX
–2–
350
5
15
17
2.6
8
14
5.5
8
1.5
2.5
0.5
1
54
3.8
1000
0.2
0.16 to 4.87
0.5 to 4.5
400
1000
9
4.5
4.5
0.3
3.3
60
56
52
50
Max
66
55
Unit
mV
mV
mV
kΩ
kΩ
M⍀
Ω
pF
␮A
␮A
␮A
␮A
␮A
␮A
␮A
␮A
dB
V
pF
Ω
V
V
mA
mA
10
11.4
5.1
5.1
0.55
8
mA
mA
mA
mA
mA
V
dB
dB
dB
dB
REV. A
AD8018
Parameter
Conditions
LOGIC INPUTS (PWDN1, 0)
Logic “1” Voltage
Logic “0” Voltage
Logic Input Bias Current
Standby Recovery Time
Min
Typ
Max
Unit
2.0
V
V
␮A
ns
0.8
240
500
RL = 10 Ω, G = +2, IS = 90% of Typical
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS 1
MAXIMUM POWER DISSIPATION
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V
Internal Power Dissipation2
Small Outline Package (R) . . . . . . . . . . . . . . . . . . . 650 mW
TSSOP Package (RU) . . . . . . . . . . . . . . . . . . . . . . 565 mW
Input Voltage (Common-Mode) . . . . . . . . . . . . . . . . . . . . ± VS
Logic Voltage, PWDN0, 1 . . . . . . . . . . . . . . . . . . . . . . . . . ± VS
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . ± 1.6 V
Output Short Circuit Duration
. . . . . . . . . . . . . . . . . . . . . . Observe Power Derating Curves
Storage Temperature Range RU, R . . . . . . . –65°C to +150°C
Operating Temperature Range . . . . . . . . . . . –40°C to +85°C
Lead Temperature Range (Soldering 10 sec) . . . . . . . . . 300°C
The maximum power that can be safely dissipated by the AD8018
is limited by the associated rise in junction temperature. The
maximum safe junction temperature for plastic encapsulated
devices is determined by the glass transition temperature of the
plastic, approximately 150°C. Temporarily exceeding this limit
may cause a shift in parametric performance due to a change
in the stresses exerted on the die by the package. Exceeding a
junction temperature of 175°C for an extended period can result
in device failure.
2.0
TJ = 150ⴗC
MAXIMUM POWER DISSIPATION – Watts
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2
Specification is for the device on a 4-layer board in free air at 85°C:
8-Lead SOIC Package: θJA = 100°C/W.
14-Lead TSSOP Package: θJA = 115°C/W.
While the AD8018 is internally short circuit protected, this may
not be sufficient to guarantee that the maximum junction temperature (150°C) is not exceeded under all conditions. To ensure
proper operation, it is necessary to observe the maximum power
derating curves.
ORDERING GUIDE
Model
AD8018AR
Temperature
Range
Package
Description
–40°C to +85°C 8-Lead Plastic
SOIC
AD8018AR–REEL
–40°C to +85°C 8-Lead SOIC
AD8018AR–REEL7 –40°C to +85°C 8-Lead SOIC
AD8018ARU
–40°C to +85°C 14-Lead Plastic
TSSOP
AD8018ARU–REEL –40°C to +85°C 14-Lead Plastic
TSSOP
AD8018ARU–REEL7 –40°C to +85°C 14-Lead Plastic
TSSOP
AD8018ARU–EVAL
Evaluation Board
Package
Option
SO-8
SO-8
SO-8
RU-14
1.5
8-LEAD SOIC PACKAGE
1.0
14-LEAD TSSOP PACKAGE
0.5
0
–50 –40 –30 –20 –10 0 10 20 30 40 50 60 70
AMBIENT TEMPERATURE – ⴗC
RU-14
Figure 3. Plot of Maximum Power Dissipation vs.
Temperature
RU-14
RU-14
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD8018 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
REV. A
80 90
–3–
WARNING!
ESD SENSITIVE DEVICE
AD8018–Typical Performance Characteristics
1000
100
VS = ⴞ2.5V
RL = 100⍀
10␮FTANT
0.1␮F
VOUT
AD8018
0.1␮F
VSIGNAL
RLOAD
50⍀
–VS
100
INOISE – pA/ Hz
ⴙVS
10
10
10␮FTANT
ⴙINOISE
1
10
TPC 1. Single-Ended Test Circuit
100
1k
10k
FREQUENCY – Hz
0.1
1M
100k
TPC 4. INOISE and VNOISE vs. Frequency
3k
150
G=2
VS = ⴞ2.5V
RL = 5⍀
VS=ⴞ2.5V
2.5k
OUTPUT IMPEDANCE – ⍀
100
OUTPUT VOLTAGE – mV
1
ⴚINOISE
VNOISE – nV/ Hz (RTI)
VNOISE
750⍀
750⍀
50
0
–50
2k
(0,0)
1.5k
1k
(1,0)
–150
(1,1)
500
–100
0
50
100
150
200
250
300
350
400
450
0
0.01
500
0.1
1
10
FREQUENCY – MHz
TIME – ns
TPC 2. Small Signal Step Response
TPC 5. Output Impedance vs. Frequency, for Full Power,
Standby, and Shutdown Modes
3
3
G=2
VS = ⴞ2.5V
RL = 5⍀
2
(+0.1%) 2
1
1
mV
OUTPUT VOLTAGE – V
1k
100
0
0
VOUT – (VINⴛ2)
–1
–1
–2
(–0.1%) –2
–3
0
50
100
150
200
250
300
350
400
450
–3
500
TIME – ns
TPC 3. Large Signal Step Response
G=2
VS = ⴞ2.5
VIN = 2V p-p
RL = 100⍀
0
10
20
30
40
50
60
TIME – ns
70
80
90
100
TPC 6. 0.1% Settling Time
–4–
REV. A
AD8018
5
5
G=2
VS = ⴞ2.5V
RL = 100⍀
2
–1
–4
–7
–10
–13
–16
–4
–7
–10
–13
–16
–19
–19
–22
–22
–25
10k
100k
1M
10M
FREQUENCY – Hz
100M
G=2
VS = ⴞ2.5V
RL = 5⍀
2
OUTPUT VOLTAGE – dBV
OUTPUT VOLTAGE – dBV
–1
–25
10k
1G
TPC 7. Output Voltage vs. Frequency
100k
1M
10M
FREQUENCY – Hz
100M
1G
TPC 10. Output Voltage vs. Frequency
2.5
4
750⍀ 750⍀
2.4
ⴙSWING
–SWING
3
VS = ⴞ2.5V
2
NORMALIZED GAIN – dB
OUTPUT SWING – Volts
2.3
2.2
2.1
2.0
1.9
1.8
(1,1)
–1
–3
–6
100k
10k
FULL POWER
–2
–5
100
1000
LOAD RESISTANCE – ⍀
G=2
VS = ⴞ2.5V
RL = 100⍀
0
–4
10
RL
50⍀
1.6
1
VIN
STANDBY
(1,0) or (0,1)
1
1.7
1.5
VOUT
1M
10M
FREQUENCY – Hz
100M
1G
TPC 11. Small Signal Frequency Response
TPC 8. Output Swing vs. RLOAD
0
–10
–10
–20
–20
CMRR – dB
PSRR – dB
–40
–50
ⴚPSRR
–60
–40
–50
–70
ⴙPSRR
–80
–90
100k
1M
10M
FREQUENCY – Hz
(1,1)
FULL POWER
G=2
VS = ⴞ2.5V
⌬VS = ⴞ1V
RL = 100⍀
G=2
VS = ⴞ2.5V
RL = 100⍀
–60
–70
100k
100M
1M
10M
FREQUENCY – Hz
100M
1G
TPC 12. CMRR vs. Frequency, Full Power, and Standby
Mode
TPC 9. PSRR vs. Frequency
REV. A
STANDBY
(1,0) or (0,1)
–30
–30
–5–
AD8018
–60
ⴙVS
10␮F
VS = ⴞ2.5V
G=4
fO = 100kHz
VOUT = 6V p–p
0.1␮F
100⍀
1/2
DIFFERENTIAL DISTORTION – dBc
7.96k⍀ 402⍀
0.1␮F
500⍀
VSIGIN
50⍀
AD8018
500⍀
AD8138
500⍀
0.1␮F
220␮F
RL AD9632
0.1␮F
500⍀
50⍀
OUT
0.1␮F
ⴚ6V
25⍀
ⴙ6V
750⍀
ⴙ6V
750⍀
ⴚ6V
AD8018
500⍀
100⍀
7.96k⍀
1/2
–70
–80
2ND HARMONIC
–90
3RD HARMONIC
–100
402⍀
10␮F
ⴚVS
0.1␮F
–110
5
100
10
LOAD RESISTANCE – ⍀
TPC 13. Differential Test Circuit
TPC 16. Differential Distortion vs. RLOAD
–60
VOUT = 6V p–p
RL = 10⍀
VS = ⴞ 2.5V
PWDN 1,0 = 1,1
–70
DIFFERENTIAL DISTORTION – dBc
DIFFERENTIAL DISTORTION – dBc
–60
–80
3RD HARMONIC
–90
2ND HARMONIC
–100
0.1
FREQUENCY – MHz
2ND HARMONIC
–90
3RD HARMONIC
–100
3
–60
DIFFERENTIAL DISTORTION – dBc
VS = ⴞ2.5V
RL = 3⍀
G=4
fO = 100kHz
PWDN 1,0 = 1,1
4
5
6
OUTPUT VOLTAGE – Volts
7
8
TPC 17. Differential Distortion vs. Peak-to-Peak Output
Voltage
–50
DIFFERENTIAL DISTORTION – dBc
–80
1.0
TPC 14. Differential Distortion vs. Frequency
3RD HARMONIC
–70
–80
2ND HARMONIC
–90
–100
–110
200
–70
–110
–110
0.01
–60
VS = ⴞ2.5V
RL = 10⍀
G=4
fO = 100kHz
PWDN 1,0 = 1,1
VS = ⴞ2.5V
RL = 10⍀
G=4
fO = 100kHz
PWDN 1,0 = 1,0 or 0,1
–70
–80
2ND HARMONIC
–90
3RD HARMONIC
–100
–110
300
400
500
600
PEAK OUTPUT CURRENT – mA
700
3
800
TPC 15. Differential Distortion vs. Peak Output Current
4
5
6
OUTPUT VOLTAGE – Volts
7
8
TPC 18. Differential Distortion vs. Peak-to-Peak Output
Voltage
–6–
REV. A
AD8018
16
18
VS = 8.00
15
16
VS = 5.25
VS = 5.00
14
PLINE – dBm
PLINE – dBm
14
13
VS = 5.00
VS = 4.75
12
VS = 4.75
VS = 4.50
12
10
11
8
VS = 3.3
3.2
3.4
3.8
4.0
4.2
4.4
3.6
TRANSFORMER TURNS RATIO
4.6
6
3.0
4.8
–20
VS = 5V
RLINE = 100⍀
f = 93kHz
TRANSIMPEDANCE – ⍀
MTPR – dBc
P = 13dBm
P = 13.5dBm
P = 14dBm
P = 12.5dBm
P = 12dBm
–60
3.6
3.8
4.0
4.2
4.4
TRANSFORMER TURNS RATIO
4.6
4.8
10M
200
1M
150
100k
–40
–50
3.4
TPC 22. Line Power vs. Turns Ratio; –75 dBc Out-of-Band
SFDR, f = 361 kHz
TPC 19. Line Power vs. Turns Ratio; MTPR = –65 dBc,
f = 43 kHz
–30
3.2
100
PHASE
10k
50
1k
0
100
–50
TRANSIMPEDANCE
10
–100
1
–150
0.1
–200
–70
–80
3
4
TRANSFORMER TURNS RATIO – N
0.01
1k
5
–30
100M
1G
20
VS = 5V
RLINE = 100⍀
f = 361kHz
–50
LOGIC 1 TO 0
TOTAL SUPPLY CURRENT – mA
–40
SFDR – dBc
100k
1M
10M
FREQUENCY – Hz
TPC 23. Open Loop Transimpedance and Phase
TPC 20. MTPR vs. Turns Ratio
P = 12.5dBm
P = 13dBm
P = 13.5dBm
P = 14dBm
–60
–70
–80
18
DECREASING
16
14
INCREASING
12
10
LOGIC 0 TO 1
8
P = 12dBm
–90
3
4
TRANSFORMER TURNS RATIO – N
6
0.86
5
0.88
0.90
0.92
0.94
0.96
0.98
POWER-DOWN VOLTAGE – Volts
1.00
1.02
TPC 24. Power-Up/-Down Threshold Voltage
TPC 21. Out-of-Band SFDR vs. Turns Ratio for Various
Line Power
REV. A
10k
–7–
PHASE – Degrees
10
3.0
AD8018
–10
–20
VIN = 2V p-p
G=2
VS = ⴞ2.5
CROSSTALK – dB
–30
–40
–50
RL = 5⍀
SIDE A DRIVEN
RL = 5⍀
SIDE B DRIVEN
–60
RL = 100⍀
SIDE B DRIVEN
–70
–80
–90
RL = 100⍀
SIDE A DRIVEN
–100
–110
100k
100M
1M
10M
FREQUENCY – Hz
1G
TPC 25. Crosstalk vs. Frequency
THEORY OF OPERATION
The AD8018 is composed of two current feedback amplifiers
capable of delivering 400 mA of output current while swinging
to within 0.5 V of either power supply, and maintaining low
distortion. A differential line driver using the AD8018 can provide
CPE performance on a single 5 V supply. This performance is
enabled by Analog Device’s XFCB process and a novel, twostage current feedback architecture featuring a patent-pending
rail-to-rail output stage.
VO
VP
A simplified schematic is shown in Figure 4. Emitter followers
buffer the positive input, VP, to provide low input current and
current noise. The low impedance current feedback summing
junction is at the negative input, VN. The output stage is another
high-gain amplifier used as an integrator to provide frequency
compensation. The complementary common-emitter output
provides the extended output swing.
A current feedback amplifier’s dynamic and distortion performance
is relatively insensitive to its closed-loop signal gain, which is
a distinct advantage over a voltage-feedback architecture. Figure
5 shows a simplified model of a current feedback amplifier. The
feedback signal is a current into the inverting node. RIN is inversely
proportional to the transconductance of the amplifier’s input stage,
gmi. Circuit analysis of the pictured follower with gain yields:
VOUT /VIN
BIAS
VN
Figure 4. Simplified Schematic
G=1
+
VO
VIN
RIN
IIN
IT = IIN
CT
RT
+
–
VOUT
TZ ( S )
=G×
TZ ( S ) + RF + G × RIN
–
where:
RF
G = 1 + RF /RG
RT
TZ ( S ) =
1 + SCT (RT )
RIN = 1/ g mi ≅ 125 Ω
RG
Figure 5. Model of Current Feedback Amplifier
FEEDBACK RESISTOR SELECTION
Recognizing that G ⫻ RIN < RF, and that the –3 dB point is set
when TZ(S) = RF, one can see that the amplifier’s bandwidth
depends primarily on the feedback resistor. There is a value of
RF below which the amplifier will be unstable, as an actual amplifier will have additional poles that will contribute excess phase
shift. The optimum value for RF depends on the gain and the
amount of peaking tolerable in the application.
In current feedback amplifiers, selection of the feedback and gain
resistors will impact the MTPR performance, bandwidth, noise,
and gain flatness. Care should be exercised in the selection of these
resistors so that the optimum performance is achieved. Table I
shows the recommended resistor values for use in a variety of gain
settings for the test circuit in TPC 1. These values are intended
to be a starting point when designing for any application.
–8–
REV. A
AD8018
Table I. Resistor Selection Guide
ERR
Gain
RF (⍀)
RG (⍀)
–1
+1
+2
+3
+4
+5
681
1k
750
511
340
230
681
∞
750
256
113
59
ADP3331
OUT
IN
VIN
C1
0.47␮F
FB
GND
SD
EOUT
R3
330k⍀
R1
953k⍀
VOUT
C2
0.47␮F
R2
301k⍀
ON
OFF
Figure 6. ADP3331 LDO
POWER-DOWN FEATURES
Two digitally programmable logic pins, PWDN1 and PWDN0,
are available on the TSSOP-14 package to select among three
different modes of operation, full power, standby and shutdown.
The DGND pin is the logic ground reference. The logic threshold voltage is established 1 V above DGND. In a typical 5 V
single-supply application, the DGND pin is connected to analog
ground. If PWDN1, PWDN0, and DGND are left unconnected,
the AD8018 will operate at full power.
Table II. Power-Down Features and Truth Table
PWDN0
PWDN1
State
Supply
Current
Output
Impedance
High
Low
High
Low
High
High
Low
Low
Full Power
Standby
Standby
Disabled
18 mA
9 mA
9 mA
300 µA
Low
Low
Low
High
METHOD FOR GENERATING A MIDSUPPLY VOLTAGE
To operate an amplifier on a single voltage supply, a voltage
midway between the supply and ground must be generated to
properly bias the inputs and the outputs.
A voltage divider can be created with two equal value resistors
(Figure 7). There is a trade-off between the power consumed by
the divider and the voltage drop across these resistors due to the
positive input bias currents. Selecting 2.5 kΩ for R1 and R2 will
create a voltage divider that draws only 1 mA from a 5 V supply.
The voltage generated with this topology can vary due to the
temperature coefficient (TC) of resistance. Resistors that are
closely matched and have a low TC will minimize variations in
the voltage reference due to temperature. One should also be
sure to use a decoupling capacitor (0.1 µF) at the node where
VREF is generated.
5V
R1
2.5k⍀
POWER SUPPLY AND DECOUPLING
The AD8018 can be powered with a good quality (i.e., low-noise)
supply anywhere in the range from 3.3 V to 8 V. However, in
order to optimize the ADSL upstream drive capability to +13 dBm
and maintain the best Spurious Free Dynamic Range (SFDR),
the AD8018 circuit should be supplied with a well regulated 5 V
supply. The 5 V supplied at the Universal Serial Bus (USB) port
may be poorly regulated. Improving the quality of the 5 V supply
will optimize the performance of the AD8018 in a Universal Serial
Bus-supplied CPE ADSL modem. This can be accomplished
through the use of a step-up dc-to-dc converter or switching
power supply followed by a low dropout (LDO) regulator such
as the ADP3331 (see Figure 6). Setting R1 to be 953 kΩ and
R2 to be 301 kΩ will result in a VOUT of 5 V.
Careful attention must be paid to decoupling the power supply
pins at the output of the dc-to-dc converter, the output of the
LDO regulator and the supply pins of the AD8018. High-quality
capacitors with low equivalent series resistance (ESR) such as
multilayer ceramic capacitors (MLCCs) should be used to minimize supply voltage ripple and power dissipation. A large, usually
tantalum, 10 µF to 47 µF capacitor located in proximity to the
AD8018 is required to provide good decoupling for lower frequency signals. In addition, 0.1 µF MLCC decoupling capacitors
should be located as close to each of the power supply pins as is
physically possible, no more than 1/8 inch away. An additional
large (4.7 µF to 10 µF) tantalum capacitor should be placed on the
board near the supply terminals to supply current for fast, largesignal changes at the AD8018 outputs.
REV. A
R2
2.5k⍀
VREF
0.1␮F
Figure 7. Midsupply Reference
DIFFERENTIAL TESTING
The test circuit shown in TPC 13 is used for measuring the differential distortion of the AD8018. A single-ended test signal is
applied to the inverting input of the AD8138 differential driver
with the noninverting input grounded. Applying the differential
output of the AD8138 through 100 Ω resistors serves to isolate
the inputs of the AD8018 differential driver and provide a wellbalanced low-distortion input signal. The differential load (RL)
of the AD8018 can be set to the equivalent of the line impedance reflected through a transformer. The AD9632 converts
the differential output voltage back to a single-ended signal.
The differential-to- single-ended converter using the AD9632
has an attenuation of –26 dB and is wired with precision resistors to optimize the balance of differential input signal. The
resulting smaller output signal can be easily measured using a
50 Ω spectrum analyzer.
–9–
AD8018
This circuit requires significant power supply bypassing. The
AD8018 operates on a split supply in this circuit. The bypassing
technique shown in TPC 13 utilizes a 220 µF tantalum capacitor
and a 0.1 µF ceramic chip capacitor in parallel, connected from
the positive to negative supply, and a 10 µF tantalum and 0.1 µF
ceramic chip capacitor in parallel, connected from each supply to
ground. The capacitors connected between the power supplies
serve to minimize any voltage ripples that might appear at the
supplies while sourcing or sinking any large differential current.
The large capacitor has a pool of charge instantly available for
the AD8018 to draw from, thus preventing any erroneous distortion results.
POWER DISSIPATION
It is important to consider the total power dissipation of the
AD8018 in order to properly size the heat sink area of an
application. Figure 8 is a simple representation of a differential
driver. With some simplifying assumptions we can estimate the
total power dissipated in this circuit. If the output current is
large compared to the quiescent current, computing the dissipation in the output devices and adding it to the quiescent power
dissipation will give a close approximation of the total power
dissipation in the package. A factor α (~0.6-1) corrects for the
slight error due to the Class A/B operation of the output stage.
It can be estimated by subtracting the quiescent current in the
output stage from the total quiescent current and ratioing that
to the total quiescent current. For the AD8018, α = 0.833.
+VS
PTOT = 4 (0.8 VO rmsVS – VO rms2 ) ×
For the AD8018, operating on a single 5 V supply and delivering a total of 16 dBm (13 dBm to the line and 3 dBm to the
matching network) into 12.5 Ω (100 Ω reflected back through
a 1:4.0 transformer plus back termination), the power is:
= 261 mW + 40 mW
= 301 mW
Using these calculations, and a θJA of 115°C/W for the TSSOP
package and 100°C/W for the SOIC, Tables III and IV show
junction temperature versus power delivered to the line for several supply voltages.
Table III. Junction Temperature vs. Line Power and
Operating Voltage for TSSOP, T AMB = 85ⴗC
VSUPPLY
PLINE, dBm 5
6
7
8
13
14
15
16
17
18
122
125
127
130
133
136
129
132
136
139
143
147
136
140
144
148
153
158
+VS
+VO
Table IV. Junction Temperature vs. Line Power and
Operating Voltage for SOIC, T AMB = 85ⴗC
RL
–VS
Figure 8. Simplified Differential Driver
Remembering that each output device dissipates for only half
the time gives a simple integral that computes the power for
each device:
1
2
115
117
119
121
123
125
–VO
–VS

∫ (V
S
– VO ) ×
1
+ 2 α IQ VS + POUT
RL
PLINE, dBm
5
VSUPPLY
6
7
8
13
14
15
16
17
18
111
113
115
116
118
120
117
119
122
124
127
130
123
126
129
132
136
139
129
133
136
140
144
149
Running the AD8018 at voltages near 8 V can produce junction
temperatures that exceed the thermal rating of the TSSOP packages and should be avoided. The shaded areas indicate junction
temperatures greater than 150°C.
2VO 
RL 
LAYOUT CONSIDERATIONS
The total supply power can then be computed as:
2
1
+ 2 α IQ VS + POUT
PTOT = 4 VS ∫|VO | − ∫VO  ×

 RL
In this differential driver, VO is the voltage at the output of one
amplifier, so 2 VO is the voltage across RL, which is the total
impedance seen by the differential driver, including back termination. Now, with two observations, the integrals are easily evaluated.
First, the integral of VO2 is simply the square of the rms value of
VO. Second, the integral of |VO| is equal to the average rectified value of VO, sometimes called the Mean Average Deviation, or
MAD. It can be shown that for a Discrete MultiTone (DMT)
signal, the MAD value is equal to 0.8 times the rms value.
As is the case with all high-speed applications, careful attention
to printed circuit board layout details will prevent associated
board parasitics from becoming problematic. Proper RF design
technique is mandatory. The PCB should have a ground plane
covering all unused portions of the component side of the board
to provide a low-impedance return path. Removing the ground
plane on all layers from the area near the input and output pins
will reduce stray capacitance, particularly in the area of the
inverting inputs. Signal lines connecting the feedback and gain
resistors should be as short as possible to minimize the inductance
and stray capacitance associated with these traces. Termination
resistors and loads should be located as close as possible to their
respective inputs and outputs. Input and output traces should
be kept as far apart as possible to minimize coupling (crosstalk)
though the board. Adherence to stripline design techniques for
long signal traces (greater than about 1 inch) is recommended.
–10–
REV. A
AD8018
Following these generic guidelines will improve the performance
of the AD8018 in all applications.
Stability Enhancements
The CPE bridge hybrid circuit presents a complex impedance to
the drive amplifiers, particularly when transformer parasitics are
factored in. To ensure stable operation under the full range of
load conditions, a series R-C network (Zoebel Network) should
be connected between each amplifier’s output and ground. The
recommended values are 10 Ω for the resistor and 1 nF for the
capacitor to create a low impedance path to ground at frequencies above 16 MHz (see Figure 2). R33 and R34 are added to
improve common-mode stability.
To optimize the AD8018’s performance as an ADSL differential
line driver, locate the transformer hybrid near the AD8018 drivers
and as close to the RJ11 jack as possible. Maintain differential
circuit symmetry into the differential driver and from the output
of the drivers through the transformer-coupled output of the bridge
circuit as much as possible.
CPE ADSL Application
The low-cost, high-output current dual AD8018 xDSL driver
amplifiers have been specifically designed to drive high fidelity
xDSL signals to within 0.5 V of the power rails, the performance
needed to provide CPE ADSL on a single 5 V supply. The
AD8018 may be used in transformer-coupled bridge hybrid circuits to drive modulated signals including Discrete MultiTone
(DMT) upstream to the central office.
Receive Channel Considerations
A transformer used at the output of the differential line driver to
step up the differential output voltage to the line has the inverse
effect on signals received from the line. A voltage reduction
or attenuation equal to the inverse of the turns ratio is realized
in the receive channel of a typical bridge hybrid. The turns ratio
of the transformer may also be dictated by the ability of the receive
circuitry to resolve low-level signals in the noisy twisted pair telephone plant. Higher turns ratio transformers effectively reduce the
received signal-to-noise ratio due to the reduction in the received
signal strength.
Evaluation Board
The AD8018ARU-EVAL evaluation board circuit in Figure 12
offers the ability to evaluate the AD8018 in a typical xDSL bridge
hybrid circuit.
The receiver circuit on these boards is typically unpopulated.
Requesting samples of the AD8022AR with the AD8018ARUEVAL board will provide the capability to evaluate the
AD8018ARU along with other Analog Devices products in a typical transceiver circuit. The evaluation circuits have been designed
to replicate the CPE side analog transceiver hybrid circuits.
The AD8022, a dual amplifier with typical RTI voltage noise of
only 2.5 nV/√Hz and a low supply current of 4 mA/amplifier, is
recommended for the receive channel.
DMT Modulation, MultiTone Power Ratio (MTPR), and
Out-of-Band SFDR
ADSL systems rely on DMT modulation to carry digital data
over phone lines. DMT modulation appears in the frequency
domain as power contained in several individual frequency
subbands, sometimes referred to as tones or bins, each of which
is uniformly separated in frequency. A uniquely encoded, Quadrature Amplitude Modulation (QAM)-like signal occurs at the center
frequency of each subband or tone. See Figure 9 for an example
of a DMT waveform in the frequency domain, and Figure 10 for
a time domain waveform. Difficulties will exist when decoding
these subbands if a QAM signal from one subband is corrupted
by the QAM signal(s) from other subbands, regardless of whether
the corruption comes from an adjacent subband or harmonics of
other subbands.
The circuit mentioned above is designed using a one-transformer
transceiver topology including a line receiver, line driver, line
matching network, an RJ11 jack for interfacing to line simulators,
and transformer-coupled inputs for single-ended-to-differential
input conversion.
AC-coupling capacitors of 0.01 µF, C8, and C10, in combination with 10 kΩ resistors R24 and R25, will form a zero frequency
at 1.6 kHz.
Transformer Selection
Customer premise ADSL requires the transmission of a +13 dBm
(20 mW) DMT signal. The DMT signal can have a crest factor
as high as 5.3, requiring the line driver to provide peak line power
of 27.5 dBm (560 mW). 27.5 dBm peak line power translates
into a 7.5 V peak voltage on the 100 Ω telephone line. Assuming
that the maximum low-distortion output swing available from
the AD8018 line driver on a 5 V supply is 4 V and, taking into
account the power lost due to the termination resistance, a step-up
transformer with turns ratio of 4.0 or greater is needed.
In the simplified differential drive circuit shown in Figure 2, the
AD8018 is coupled to the phone line through a step-up transformer with a 1:4 turns ratio. R1 and R2 are back-termination
or line-matching resistors, each 3.1 Ω (100 Ω/(2 × 42)), where
100 Ω is the approximate phone line impedance. The total differential load for the AD8018, including the termination resistors,
is 12.5 Ω. Even under these conditions the AD8018 provides low
distortion signals to within 0.5 V of the power rails.
REV. A
Conventional methods of expressing the output signal integrity
of line drivers, such as single-tone harmonic distortion or THD,
two-tone InterModulation Distortion (IMD), and third order
intercept (IP3), become significantly less meaningful when
amplifiers are required to process DMT and other heavily
modulated waveforms. A typical ADSL upstream DMT signal
can contain as many as 27 carriers (subbands or tones) of
QAM signals. MultiTone Power Ratio (MTPR) is the relative
difference between the measured power in a typical subband (at
one tone or carrier) versus the power at another subband specifically selected to contain no QAM data. In other words, a
selected subband (or tone) remains open or void of intentional
power (without a QAM signal), yielding an empty frequency bin.
MTPR, sometimes referred to as the “empty bin test,” is
typically expressed in dBc, similar to expressing the relative
difference between single-tone fundamentals and second or
third harmonic distortion components. Measurements of MTPR
are typically made on the line side or secondary side of the
transformer.
–11–
AD8018
4
20
3
0
–20
VOLTS
POWER – dBm
2
–40
1
0
–1
–60
–2
–3
–0.25
–80
0
50
100
FREQUENCY – kHz
150
Figure 9. DMT Waveform in the Frequency Domain
–0.2
–1.5
–1.0
–0.05
0
TIME – ms
0.05
1.0
1.5
0.2
Figure 10. DMT Signal in the Time Domain
MTPR versus transformer turns ratio is depicted in TPC 21 and
covers a variety of line power ranging from +12 dBm to +14 dBm.
As the turns ratio increases, the driver hybrid can deliver more
undistorted power due to higher output current capability.
Significant degradation of MTPR will occur if the output of the
driver swings to the rails, causing clipping at the DMT voltage
peaks. Driving DMT signals to such extremes not only compromises “in-band” MTPR, but will also produce spurs that exist
outside of the frequency spectrum containing the desired DMT
power. “Out-of-band” spurious free dynamic range (SFDR) can
be defined as the relative difference in amplitude between these
spurs and a tone in one of the upstream bins. Compromising
out-of-band SFDR is equivalent to increasing near end crosstalk (NEXT). Regardless of terminology, maintaining out-of-band
SFDR while reducing NEXT will improve the overall performance
of the modems connected at either end of the twisted pair.
TPC 21 shows how SFDR varies versus transformer turns ratio
for line power ranging from +12 dBm to +14 dBm. As line
power increases, or turns ratio decreases, SFDR degrades. The
power contained in the spurs can be measured relative to the
power contained in a typical upstream carrier and is expressed
in dBc as SFDR, similar to MTPR.
Generating DMT Signals
At this time, DMT-modulated waveforms are not typically
menu-selectable items contained within AWGs. Even using
AWG software to generate DMT signals, AWGs that are available
today may not deliver DMT signals sufficient in performance
with regard to MTPR due to limitations in the D/A converters
and output drivers used by AWG manufacturers. Similar to
evaluating single-tone distortion performance of an amplifier,
MTPR evaluation requires a DMT signal generator capable of
delivering MTPR performance better than that of the driver
under evaluation. Generating DMT signals can be accomplished using a Tektronics AWG 2021 equipped with Option
4, (12-/24-bit, TTL Digital Data Out), digitally coupled to
Analog Devices’ AD9754, a 14-bit TxDAC®, buffered by an
AD8002 amplifier configured as a differential driver. Note that
the DMT waveforms (available on the Analog Devices website,
http://www.analog.com), or similar .WFM files are needed to
produce the digital data required to drive the TxDAC from the
optional TTL Digital Data output of the TEK AWG2021.
The supply voltage of the driver can also affect SFDR. As the
supply voltage is increased, voltage swing is increased as well,
resulting in the ability to deliver more power to the line without sacrificing performance. This can be seen in TPC 22. Less
undistorted power is available when lower turns ratio transformers are used due to voltage clipping of the signal.
TxDAC is a trademark of Analog Devices, Inc.
–12–
REV. A
AD8018
TP10
R30
0⍀
VCC-T
55
C8
0.1␮F
VCC
R8
100⍀
AD8018
R24
10k⍀
2
JP4
A 1
P4
2
P4
3
B
A
CAPPOLY
R18
750⍀
R33
10k⍀
R19
750⍀
R34
10k⍀
10⍀
2 1WATT
10
CAPPOLY
C6
DNI
C27
1000pF
1
R4
10⍀
U1
R14
100⍀
VCC-T
TP4
C1
DNI
AD8022
53
R17
2.49k⍀
C20
0.1␮F
P3
3
P3
2
P3
R6
DNI
VCC
R5
DNI
R7
DNI
AD8022
DNI
C16
DNI
C3
DNI
TP5
Figure 11. EVAL Board Schematic
VCC
R28
DNI
100⍀
R26
PDN0
JP2
U1
AD8018
100⍀
R25
JP1
0.1␮F
C24
C23
DNI
C19
DNI
25V
U2 DECOUPLING
R13
DNI
R27
DNI
C17
10␮F
25V
VCC-R
VCC;8
AGND;4
DNI: DO NOT INSTALL
C15
0.01␮F
TB1 2
U2
54
VCC-T
C26
0.1␮F
C18
DNI
R10
DNI
VCC-R
TP18
TP19
TB1 1
C14
10␮F
2
1
L5
BEAD
C2
DNI
R9
DNI
TP17
2
TP23 TP24 TP25 TP26
VCC-R
AGND;4
DNI
VCC
TP9
R12
DNI
U2
VCC
6
7 8
TP8
R31
0⍀
TP11
5
TP2
R21
DNI
+V
56
4
C12
DNI
1
C10
0.1␮F
2
3
PR2
JP3
AD8018
R32
DNI
8
3
C7
DNI
1 R1
R29
10k⍀
VCC
0.1␮F
C25
PDN1
DGND NC1 NC2 NC3
Figure 12. Input Control Circuit
REV. A
9
TP1
3
2
R15
50⍀
R16
2.49k⍀
C22
1000pF
C9
DNI
7
CAPPOLY
2
1
R2
750⍀
C5
0.1␮F
T1
NC = 5,6
4
CAPPOLY
R3
10⍀
2
C28
DNI
C4
DNI
R20
DNI
VCC
B
1
TP7 PR1
C11
DNI
U1
R11
50⍀
3
P4
TP6
+V
–13–
AD8018
Figure 13. Assembly—Primary Side
Figure 14. Silk Screen—Primary Side
–14–
REV. A
AD8018
Figure 15. Layer 1—Primary Side
Figure 16. Layer 2—Ground Plane
REV. A
–15–
AD8018
Figure 17. Layer 3—Power Plane
Figure 18. Layer 4—Secondary Side
–16–
REV. A
AD8018
Figure 19. Assembly—Secondary Side
REV. A
–17–
AD8018
EVALUATION BOARD—BILL OF MATERIALS
Qty.
Description
Vendor
Ref Desc.
2
2
5
2
4
3
1
1
6
2
2
5
2
3
2
2
4
2
3
4
1
2
2
1
1
4
2
4
1
2
2
1
1
4
4
1,000 pF 50 V. 1206 ceramic chip capacitor
0.01 µF 50 V. 1206 ceramic chip capacitor
0.1 µF 50 V. 1206 size ceramic chip capacitor
1.0 µF 16 V. 1206 size ceramic chip capacitor
# 26 red (solid) wire jumper
10 µF 16 V. ‘C’ size Tantalum chip capacitor
Ferrite bead (with # 22 wire)
10 Ω 5% 3.0 W. metal oxide power resistor
0 Ω 5% 1/8 W. 1206 size chip resistor
10.0 Ω 1% 1/8 W. 1206 size chip resistor
49.9 Ω 1% 1/8 W. 1206 size chip resistor
100 Ω 1% 1/8 W. 1206 size chip resistor
2.49 kΩ 1% 1/8 W. 1206 size chip resistor
750 Ω 1% 1/8 W. 1206 size chip resistor
10.0 kΩ 0.1% 0805 size chip resistor
10.0 kΩ 1% 1/8 W. 1206 size chip resistor
Test Point (Black) [GND]
Test Point (Brown)
Test Point (Red)
Test Point (Orange)
Test Point (Yellow)
Test Point (Blue)
Test Point (Green)
2 × 5-pin strips (1/4 of a 20-pin Samtek ‘SIP’ strip socket)
2 Pos. GRAY term. blk. # 25.161.0253 (Newark # 51F4106)
0.1 inch ctr. shunt Berg # 65474 -001
2 pin gold male header 0.1 inch ctr. Berg # 69157 -102
50 Ω BNC pc mount Telegartner # J01001A1944
AMP# 555154 -1 MOD. JACK (SHIELDED) 6 –6
3-pin gold male header Waldom D-K # WM 2723 -ND
3-pin gold male locking header Waldom # WM 2701 -ND
AD8018ARU ADSL Driver hybrid
AD8018 TSSOP1T Non-Inverting REV. A Evaluation PC board
# 4 –40 × 1/4" panhead ss machine screw
# 4 –40 × 1/2" threaded alum. standoffs
ADS # 4-5-20
ADS # 4-5-19
ADS # 4-5-18
Newark # 83F6841
ADS # 10-14-3
ADS # 4-7-6
ADS # 48-1-1
D-K # P10W-3BK-ND
ADS # 3-18-88
ADS # 3-18-120
ADS # 3-14-26
ADS # 3-18-40
ADS # 3-18-71
ADS # 3-18-8
ADS # 3-36-5
ADS # 3-18-119
ADS # 12-18-44
ADS # 12-18-59
ADS # 12-18-43
ADS # 12-18-60
ADS # 12-18-32
ADS # 12-18-62
ADS # 12-18-61
ADS # 11-2-14
ADS# 12-19-10
ADS # 11-2-38
ADS # 11-2-37
ADS # 12-6-22
ADS # 12-20-5
ADS # 12-3-80
ADS # 12-3-79
ADS # AD8018ARU
DCS
ADS # 30-1-1
ADS # 30-16-2
C22, 27
C15, 23
C5, 20, 24 -26
C8, 10
C4, 6, 7, 9
C14, 17, 19
L5
R1
C11, 12, R20, 21, 30, 31
R3, 4
R11, 15
R8, 14, 25, 26, 32
R16, 17
R2, 18, 19
R33, 34
R24 and 29
TP23–26 (GND.)
TP4, 5
TP17–19
TP1, 2, 10, 11
TP3
TP6, 8
TP7, 9
(T1)
TB1, 2
JP1–4
JP1, 2
S3–6
P1
JP3, 4
P3, 4
U1 (D.U.T.)
Eval. PC Board
–18–
REV. A
AD8018
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
14 Lead TSSOP
(RU-14)
0.201 (5.10)
0.197 (5.00)
0.193 (4.90)
0.1968 (5.00)
0.1890 (4.80)
8
0.1574 (4.00)
0.1497 (3.80)
5
1
0.2440 (6.20)
0.2284 (5.80)
14
0.0196 (0.50)
ⴛ 45ⴗ
0.0099 (0.25)
0.0500 (1.27)
BSC
0.020 (0.51)
0.013 (0.33)
8ⴗ
0.0098 (0.25) 0ⴗ
0.0075 (0.19)
0.252
(6.40)
BSC
1
0.0688 (1.75)
0.0532 (1.35)
SEATING
PLANE
8
0.177 (4.50)
0.173 (4.40)
0.169 (4.30)
PIN 1
0.0098 (0.25)
0.0040 (0.10)
C01519a–.5–11/00 (rev. A)
8 Lead SOIC
(SO-8)
7
PIN 1
0.050 (1.27)
0.016 (0.40)
CONTROLLING DIMENSIONS ARE IN MILLIMETERS
ALL DIMENSIONS PER JEDEC STANDARDS MS-012 AA
0.059 (1.50)
0.093 (1.00)
0.031 (0.80)
0.0256 (0.65)
BSC
0.006 (0.15)
0.002 (0.05)
0.047 (1.2)
MAX
8ⴗ
0ⴗ
0.0118 (0.30)
SEATING 0.008 (0.20)
0.0075 (0.19) PLANE
0.004 (0.09)
0.030 (0.75)
0.024 (0.60)
0.018 (0.45)
PRINTED IN U.S.A.
CONTROLLING DIMENSIONS ARE IN MILLIMETERS
REV. A
–19–
Similar pages