ON NLAS7222C High-speed usb 2.0 (480 mbps) dpdt switch Datasheet

NLAS7222B, NLAS7222C
High-Speed USB 2.0
(480 Mbps) DPDT Switches
ON Semiconductor’s NLAS7222B and NLAS7222C are part of a
series of analog switch circuits that are produced using the company’s
advanced sub−micron CMOS technology, achieving industry−leading
performance.
Both the NLAS7222B and NLAS7222C are 2− to 1−port analog
switches. Their wide bandwidth and low bit−to−bit skew allow them to
pass high−speed differential signals with good signal integrity. Each
switch is bidirectional and offers little or no attenuation of the
high−speed signals at the outputs. Industry−leading advantages
include a propagation delay of less than 250 ps, resulting from its low
channel resistance and low I/O capacitance. Their high
channel−to−channel crosstalk rejection results in minimal noise
interference. Their bandwidth is wide enough to pass High−Speed
USB 2.0 differential signals (480 Mb/s).
Features
•
•
•
•
•
•
•
RON is Typically 8.0 at VCC = 3.3 V
Low Crosstalk: −30 dB @ 250 MHz
Low Current Consumption: 1.0 A
Channel On−Capacitance: 8.0 pF (Typical)
VCC Operating Range: 1.65 V to 4.5 V
> 700 MHz Bandwidth (or Data Frequency)
These are Pb−Free Devices
http://onsemi.com
MARKING
DIAGRAM
UQFN10
CASE 488AT
1
XX
=
M
G
=
=
XX M G
G
Device Code
7222B = AS
7222C = AT
Date Code
Pb−Free Device
(Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
Typical Applications
• Differential Signal Data Routing
• USB 2.0 Signal Routing
Important Information
• Continuous Current Rating Through Each Switch ±300 mA
• 8 kV I/O to GND ESD Protection
© Semiconductor Components Industries, LLC, 2011
June, 2011 − Rev. 5
1
Publication Order Number:
NLAS7222B/D
NLAS7222B, NLAS7222C
HSD1−
7
OE
8
VCC
9
HSD2−
HSD1+
HSD1−
6
7
6
CONTROL
5
D−
4
GND
OE
8
VCC
9
5
HSD2+
4
HSD2−
3
GND
CONTROL
S
10
3
1
2
HSD1+
HSD2+
D+
S
Figure 1. Pin Connections and Logic Diagram
(NLAS7222B, Top View)
1
2
D+
D−
Figure 2. Pin Connections and Logic Diagram
(NLAS7222C, Top View)
Table 1. PIN DESCRIPTION
Pin
10
Table 2. TRUTH TABLE
Function
S
Select Input
OE
OE
S
HSD1+,
HSD1−
HSD2+,
HSD2−
1
0
0
X
0
1
OFF
ON
OFF
OFF
OFF
ON
Output Enable
HSD1+, HSD1−, HSD2+,
HSD2−, D+, D−
Data Ports
MAXIMUM RATINGS
Symbol
Pins
VCC
VCC
VIS
HSD1+, HSD1−
HSD2+, HSD2−
Parameter
Value
Unit
−0.5 to +5.5
V
−0.5 to VCC + 0.3
V
Positive DC Supply Voltage
Analog Signal Voltage
D+, D−
VIN
S, OE
ICC
VCC
TS
−0.5 to +5.5
Control Input Voltage, Output Enable Voltage
Positive DC Supply Current
Storage Temperature
−0.5 to +5.5
V
50
mA
−65 to +150
°C
IIS_CON
HSD1+, HSD1−
HSD2+, HSD2−,
D+, D−
Analog Signal Continuous Current−Closed Switch
$300
mA
IIS_PK
HSD1+, HSD1−
HSD2+, HSD2−,
D+, D−
Analog Signal Continuous Current 10% Duty Cycle
$500
mA
Control Input Current, Output Enable Current
$20
mA
IIN
S, OE
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
RECOMMENDED OPERATING CONDITIONS
Symbol
Pins
VCC
VIS
HSD1+, HSD1−
HSD2+, HSD2−
Parameter
Min
Max
Unit
Positive DC Supply Voltage
1.65
4.5
V
Analog Signal Voltage
GND
VCC
V
D+, D−
VIN
TA
S, OE
Control Input Voltage, Output Enable Voltage
Operating Temperature Range
GND
4.5
GND
VCC
V
−40
+85
°C
Minimum and maximum values are guaranteed through test or design across the Recommended Operating Conditions, where
applicable. Typical values are listed for guidance only and are based on the particular conditions listed for section, where applicable.
These conditions are valid for all values found in the characteristics tables unless otherwise specified in the test conditions.
http://onsemi.com
2
NLAS7222B, NLAS7222C
ESD PROTECTION
Symbol
Value
Unit
ESD
Human Body Model − All Pins
Parameter
2.0
kV
ESD
Human Body Model − I/O to GND
8.0
kV
DC ELECTRICAL CHARACTERISTICS
CONTROL INPUT, OUTPUT ENABLE (Typical: T = 25°C, VCC = 3.3 V)
−40°C to +85°C
Symbol
Pins
Parameter
Test Conditions
VCC (V)
Min
Typ
Max
Unit
−
−
V
0.4
0.4
0.5
V
±1.0
A
VIH
S, OE
Control Input, Output
Enable HIGH Voltage
(See Figure 3)
2.7
3.3
4.2
1.3
1.4
1.6
VIL
S, OE
Control Input, Output
Enable LOW Voltage
(See Figure 3)
2.7
3.3
4.2
−
IIN
S, OE
Control Input, Output
Enable Leakage
Current
1.65 − 4.5
−
0 ≤ VIS ≤ VCC
−
SUPPLY AND LEAKAGE CURRENT (Typical: T = 25°C, VCC = 3.3 V)
−40°C to +85°C
VCC (V)
Min
Typ
Max
Unit
1.65 − 4.5
−
−
1.0
A
3.6
−
−
10
A
0 ≤ VIS ≤ VCC
1.65 − 4.5
−
−
±1.0
A
0 ≤ VIS ≤ 4.5 V
0
−
−
±1.0
A
Symbol
Pins
Parameter
ICC
VCC
Quiescent Supply
Current
VIS = VCC or GND; IOUT =
0A
Test Conditions
ICCT
VCC
Increase in ICC
per
Control Voltage
VIN = 2.6 V
IOZ
HSD1+, HSD1−
HSD2+, HSD2−
OFF State
Leakage Current
IOFF
D+, D−
Power OFF
Leakage Current
HIGH SPEED ON RESISTANCE (Typical: T = 25°C, VCC = 3.3 V)
−40°C to +85°C
Symbol
Pins
Parameter
Test Conditions
VCC (V)
Min
Typ
Max
Unit
RON
On−Resistance
VIS = 0 V to 0.4 V, ION =
8 mA
2.7
3.3
4.2
−
9.0
8.0
7.0
12
10
8.0
RFLAT
On−Resistance
Flatness
VIS = 0 V to 1.0 V, ION =
8 mA
2.7
3.3
4.2
−
1.6
1.5
1.4
−
RON
On−Resistance
Matching
VIS = 0 V to 0.4 V, ION =
8 mA
2.7
3.3
4.2
−
1.05
0.85
0.65
−
http://onsemi.com
3
NLAS7222B, NLAS7222C
DC ELECTRICAL CHARACTERISTICS (continued)
FULL SPEED ON RESISTANCE (Typical: T = 25°C, VCC = 3.3 V)
−40°C to +85°C
Symbol
Pins
Parameter
Test Conditions
VCC (V)
Min
Typ
Max
Unit
12
10.5
8.5
RON
On−Resistance
VIS = 0 V to VCC, ION =
8 mA
2.7
3.3
4.2
9.0
8.5
7.5
RFLAT
On−Resistance
Flatness
VIS = 0 V to 1.0 V, ION =
8 mA
2.7
3.3
4.2
1.6
1.5
1.4
RON
On−Resistance
Matching
VIS = 0 V to VCC, ION =
8 mA
2.7
3.3
4.2
2.20
2.45
2.65
AC ELECTRICAL CHARACTERISTICS
TIMING/FREQUENCY (Typical: T = 25°C, VCC = 3.3 V, RL = 50 , CL = 5 pF, f = 1 MHz)
−405C to +855C
VCC (V)
Min
Typ
Max
Unit
tON
Closed Turn−ON Time
to Open
1.65 − 4.5
−
14
30
ns
tOFF
Open to Turn−OFF Time
Closed
1.65 − 4.5
−
10
20
ns
1.65 − 4.5
3.0
4.4
7.0
ns
1.65 − 4.5
−
500
−
MHz
−
750
−
Symbol
Pins
Parameter
tBBM
Break−Before−Make
Delay
BW
−3 dB Bandwidth
Test Conditions
CL = 5 pF
CL = 0 pF
ISOLATION (Typical: T = 25°C, VCC = 3.3 V, RL = 50 , CL = 5 pF, f = 1 MHz)
−405C to +855C
Symbol
Pins
OIRR
Open
XTALK
HSD1+ to
HSD1−
VCC (V)
Min
Typ
Max
Unit
OFF−Isolation
f = 250 MHz
1.65 − 4.5
−
−22
−
dB
Non−Adjacent
Channel Crosstalk
f = 250 MHz
1.65 − 4.5
−
−30
−
dB
Parameter
Test Conditions
NLAS7222B CAPACITANCE (Typical: T = 25°C, VCC = 3.3 V, RL = 50 , CL = 5 pF, f = 1 MHz)
−405C to +855C
Min
Typ
Max
Unit
Control Pin Input Capacitance
VCC = 0 V
−
3.0
−
pF
D+ to
HSD1+ or
HSD2+
ON Capacitance
VCC = 3.3 V; OE = 0 V
S = 0 V or 3.3 V
−
8.0
−
pF
HSD1n or
HSD2n
OFF Capacitance
VCC = VIS = 3.3 V; OE = 0 V
S = 3.3 V or 0 V
−
4.5
−
pF
Symbol
Pins
CIN
S, OE
CON
COFF
Parameter
Test Conditions
http://onsemi.com
4
NLAS7222B, NLAS7222C
NLAS7222C CAPACITANCE (Typical: T = 25°C, VCC = 3.3 V, RL = 50 , CL = 5 pF, f = 1 MHz)
−405C to +855C
Min
Typ
Max
Unit
VCC = 0 V
−
3.0
−
pF
ON Capacitance
VCC = 3.3 V; OE = 0 V
S = 0 V or 3.3 V
−
10
−
pF
OFF Capacitance
VCC = VIS = 3.3 V; OE = 3.3 V
S = 3.3 V or 0 V
−
5.5
−
pF
Symbol
Pins
Parameter
CIN
S, OE
Control Pin, Output Enable Input Capacitance
CON
D+ to
HSD1+ or
HSD2+
COFF
HSD1n or
HSD2n
Test Conditions
http://onsemi.com
5
NLAS7222B, NLAS7222C
140
120
ICC, (A)
100
80
VCC = 4.2 V
60
VCC = 3.3 V
40
VCC = 2.7 V
20
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
VIN, (V)
Figure 3. ICC vs. VIN
VCC
DUT
VCC
Input
Output
GND
VOUT
0.1 F
50 35 pF
tBMM
Output
50 % OF
DROOP
VOLTAGE
DROOP
Switch Select Pin
Figure 4. tBBM (Time Break−Before−Make)
VCC
Input
DUT
VCC
0.1 F
50%
0V
Output
VOUT
Open
50%
50 VOH
90%
35 pF
90%
Output
VOL
Input
tON
Figure 5. tON/tOFF
VCC
VCC
Input
DUT
Output
50%
50%
0V
50 VOUT
Open
tOFF
VOH
35 pF
Output
Input
tOFF
Figure 6. tON/tOFF
http://onsemi.com
6
10%
10%
VOL
tON
NLAS7222B, NLAS7222C
50 Reference
DUT
Transmitted
Input
Output
50 Generator
50 Channel switch control/s test socket is normalized. Off isolation is measured across an off channel. On loss
is the bandwidth of an On switch. VISO, Bandwidth and VONL are independent of the input signal direction.
ǒVVOUT
Ǔ for VIN at 100 kHz
IN
VOUT
Ǔ for VIN at 100 kHz to 50 MHz
VONL = On Channel Loss = 20 Log ǒ
VIN
VISO = Off Channel Isolation = 20 Log
Bandwidth (BW) = the frequency 3 dB below VONL
VCT = Use VISO setup and test to all other switch analog input/outputs terminated with 50 Figure 7. Off Channel Isolation/On Channel Loss (BW)/Crosstalk
(On Channel to Off Channel)/VONL
http://onsemi.com
7
NLAS7222B, NLAS7222C
APPLICATIONS INFORMATION
(www.usb.org), the industry group responsible for defining
the USB certification requirements. The test patterns were
generated by a PC and MATLAB software, and were
inputted to the analog switch through USB connectors J1
(HSD1) or J2 (HSD2). A USB certified device was plugged
into connector J4 to function as a data transceiver. The high
speed and full speed tests used a flash memory device, while
the low speed tests used a mouse. Test connectors J3 and J5
provide a direct connection of the USB device and were used
to verify that the analog switch does not distort the data
signals.
The low on resistance and capacitance of the NLAS7222B
provides for a high bandwidth analog switch suitable for
applications such as USB data switching. Results for the
USB 2.0 signal quality tests will be shown in this section,
along with a description of the evaluation test board. The
data for the eye diagram signal quality and jitter tests verifies
that the NLAS7222B can be used as a data switch in low, full
and high speed USB 2.0 systems.
Figures 8, 9 and 10 provide a description of the test
evaluation board. The USB tests were conducted per the
procedures provided by the USB Implementers Forum
Figure 8. Schematic of the NLAS7222B USB Demo Board
http://onsemi.com
8
NLAS7222B, NLAS7222C
Figure 9. Block Diagram of the NLAS7222B USB Demo Board
Figure 10. Photograph of the NLAS7222B USB Demo Board
ORDERING INFORMATION
Marking
Package
Shipping†
NLAS7222BMUTAG
AS
UQFN10
(Pb−Free)
3000 / Tape & Reel
NLAS7222BMUTBG
AS
UQFN10
(Pb−Free)
3000 / Tape & Reel
NLAS7222CMUTBG
AT
UQFN10
(Pb−Free)
3000 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
9
NLAS7222B, NLAS7222C
PACKAGE DIMENSIONS
UQFN10, 1.4x1.8, 0.4P
CASE 488AT−01
ISSUE A
EDGE OF PACKAGE
D
ÉÉ
ÉÉ
ÉÉ
PIN 1 REFERENCE
2X
2X
0.10 C
L1
E
0.10 C
EXPOSED Cu
A
0.05 C
A1
0.05 C
A1
C
SIDE VIEW
3
9X
DETAIL A
Bottom View
(Optional)
B
TOP VIEW
10X
5
SEATING
PLANE
ÉÉ
ÉÉ
DIM
A
A1
A3
b
D
E
e
L
L1
L3
MOLD CMPD
A3
DETAIL B
Side View
(Optional)
1.700
0.0669
0.663
0.0261
6
e
1
0.200
0.0079
10 X
L3
b
MILLIMETERS
MIN
MAX
0.45
0.60
0.00
0.05
0.127 REF
0.15
0.25
1.40 BSC
1.80 BSC
0.40 BSC
0.30
0.50
0.00
0.15
0.40
0.60
MOUNTING FOOTPRINT
e/2
L
10
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS
3. DIMENSION b APPLIES TO PLATED TERMINAL
AND IS MEASURED BETWEEN 0.25 AND 0.30 MM
FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED PAD
AS WELL AS THE TERMINALS.
A
1
0.10 C A B
0.05 C
9X
0.563
0.0221
2.100
0.0827
NOTE 3
BOTTOM VIEW
0.400
0.0157
PITCH
10 X
0.225
0.0089
SCALE 20:1
mm Ǔ
ǒinches
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
10
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NLAS7222B/D
Similar pages