LINER LT1236ALS8 Precision, low noise, low profile hermetic voltage reference Datasheet

LT1236LS8
Precision, Low Noise, Low
Profile Hermetic Voltage Reference
Features
n
n
n
n
n
n
n
n
Description
Hermetic 5mm × 5mm LCC Leadless Chip Carrier
Package:
Insensitive to Humidity
Thermal Hysteresis: 8ppm (0°C to 70°C)
Thermal Hysteresis: 60ppm (–40°C to 85°C)
Low Drift:
A-Grade: 5ppm/°C Max
B-Grade: 10ppm/°C Max
High Accuracy:
A-Grade: ±0.05% Max
B-Grade: ±0.10% Max
Low Noise: <1ppm Peak-to-Peak (0.1Hz to 10Hz)
100% Noise Tested
Sinks and Sources ±10mA
Wide Supply Range to 40V
8-Pin (5mm × 5mm) LS8 Package
Applications
n
n
n
n
n
n
Instrumentation and Test Equipment
High Resolution Data Acquisition Systems
A/D and D/A Converters
Precision Regulators
Precision Scales
Digital Voltmeters
The LT®1236LS8 is a precision reference that combines
low drift and noise with excellent long-term stability and
high output accuracy. The reference output will both source
and sink up to 10mA and remains very constant with input
voltage variations.
The hermetic package provides outstanding humidity and
thermal hysteresis performance. The LT1236LS8 is only
5mm × 5mm × 1.5mm, offering an alternative to large
through-hole metal can voltage references, such as the
industry standard LT1021. The LT1236LS8 offers similar
performance to the LT1236, with additional stability from
the hermetic package.
LT1236LS8 is based on a buried Zener diode structure,
which enables temperature and time stability, and extremely
low noise performance of < 1ppm peak-to-peak. Noise is
100% tested in production. The LT1236LS8 operates on a
supply voltage from 7.2V up to 40V. The subsurface Zener
exhibits better time stability than even the best bandgap
reference, and the hermetic package maintains that stability
over a wide range of environmental conditions.
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
Typical Application
Typical Distribution of Temperature Drift
24
DISTRIBUTION
22 OF THREE RUNS
20
Basic Connection
18
VIN
IN
OUT
VOUT
GND
UNITS (%)
16
LT1236LS8
14
12
10
8
6
LT1236LS8 TA01
4
2
0
–3
–2
–1
0
1
OUTPUT DRIFT (ppm/°C)
2
3
LT1236LS8 TA02
1236ls8f
1
LT1236LS8
Absolute Maximum Ratings
Pin Configuration
(Note 1)
Input Voltage..............................................................40V
Input/Output Voltage Differential...............................35V
Trim Pin-to-Ground Voltage
Positive.................................................. Equal to VOUT
Negative...............................................................–20V
Output Short-Circuit Duration
VIN = 35V...........................................................10 sec
VIN ≤ 20V...................................................... Indefinite
Operating Temperature Range..................– 40°C to 85°C
Storage Temperature Range................... –65°C to 150°C
TOP VIEW
NC*
NC*
1
VIN
2
NC*
3
8
4
7
NC*
6
VOUT
5
TRIM**
GND
LS8 PACKAGE
8-PIN LEADLESS CHIP CARRIER (5mm × 5mm)
*CONNECTED INTERNALLY.
D0 NOT CONNECT EXTERNAL
CIRCUITRY TO THESE PINS
**SEE APPLICATIONS
INFORMATION SECTION
TJMAX = 125°C, θJA = 120°C/W
PACKAGE LID IS GND
Order Information
LEAD FREE FINISH
PART MARKING*
PACKAGE DESCRIPTION
SPECIFIED TEMPERATURE RANGE
LT1236AILS8-5#PBF†
12365
8-Lead Ceramic LCC 5mm × 5mm
–40°C to 85°C
LT1236BILS8-5#PBF†
12365
8-Lead Ceramic LCC 5mm × 5mm
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
†This product is only offered in trays. For more information go to: http://www.linear.com/packaging/
Electrical Characteristics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 10V, IOUT = 0, unless otherwise noted.
LT1236LS8-5
PARAMETER
CONDITIONS
MIN
TYP
MAX
Output Voltage (Note 2)
LT1236ALS8
LT1236BLS8
4.9975
4.9950
5.000
5.000
5.0025
5.0050
Output Voltage Temperature Coefficient (Note 3)
LT1236ALS8
LT1236BLS8
2
5
5
10
ppm/°C
ppm/°C
Line Regulation (Note 4)
7.2V ≤ VIN ≤ 10V
4
12
20
6
10
ppm/V
ppm/V
ppm/V
ppm/V
25
40
ppm/mA
ppm/mA
l
10V ≤ VIN ≤ 40V
2
l
Load Regulation (Sourcing Current)
(Note 4)
0 ≤ IOUT ≤ 10mA
15
l
UNITS
V
V
1236ls8f
2
LT1236LS8
Electrical Characteristics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 10V, IOUT = 0, unless otherwise noted.
LT1236LS8-5
PARAMETER
CONDITIONS
Load Regulation (Sinking Current)
(Note 4)
0 ≤ IOUT ≤ 10mA
MIN
TYP
MAX
UNITS
60
100
150
ppm/mA
ppm/mA
0.8
1.2
1.5
mA
mA
3.5
µVP-P
µVRMS
l
Supply Current
l
Output Voltage Noise
(Note 5)
0.1Hz ≤ f ≤ 10Hz
10Hz ≤ f ≤ 1kHz
3.0
2.2
Long-Term Stability of Output Voltage (Note 6)
∆t = 1000Hrs Non-Cumulative
20
ppm
Temperature Hysteresis of Output (Note 7)
∆T = ±25°C
∆T = 0°C to 70°C
∆T = –40°C to 85°C
3
8
60
ppm
ppm
ppm
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Output voltage is measured immediately after turn-on. Changes
due to chip warm-up are typically less than 0.005%.
Note 3: Temperature coefficient is measured by dividing the change in
output voltage over the temperature range by the change in temperature.
Incremental slope is also measured at 25°C.
Note 4: Line and load regulation are measured on a pulse basis. Output
changes due to die temperature change must be taken into account
separately.
Note 5: RMS noise is measured with a 2-pole highpass filter at 10Hz and a
2-pole lowpass filter at 1kHz. The resulting output is full-wave rectified and
then integrated for a fixed period, making the final reading an average as
opposed to RMS. Correction factors are used to convert from average to
RMS, and 0.88 is used to correct for the non-ideal bandbass of the filters.
Peak-to-peak noise is measured with a single highpass filter at 0.1Hz and a
2-pole lowpass filter at 10Hz. The unit is enclosed in a still-air environment
to eliminate thermocouple effects on the leads. Test time is 10 seconds.
Note 6: Long-term stability typically has a logarithmic characteristic and
therefore, changes after 1000 hours tend to be much smaller than before
that time. Total drift in the second thousand hours is normally less than
one third that of the first thousand hours, with a continuing trend toward
reduced drift with time. Significant improvement in long-term drift can
be realized by preconditioning the IC with a 100-200 hour, 125°C burn in.
Long term stability will also be affected by differential stresses between
the IC and the board material created during board assembly. Temperature
cycling and baking of completed boards is often used to reduce these
stresses in critical applications.
Note 7: Hysteresis in output voltage is created by package stress that
differs depending on whether the IC was previously at a higher or lower
temperature. Output voltage is always measured at 25°C, but the IC is
cycled to high or low temperature before successive measurements.
Hysteresis is roughly proportional to the square of temperature change.
Hysteresis is not normally a problem for operational temperature
excursions, but can be significant in critical narrow temperature range
applications where the instrument might be stored at high or low
temperatures. Hysteresis measurements are preconditioned by one
temperature cycle.
1236ls8f
3
LT1236LS8
Typical Performance Characteristics
Ripple Rejection
115
Ripple Rejection
130
f = 150Hz
VIN = 15V
COUT = 0
120
110
Start-Up
8
7
100
95
OUTPUT VOLTAGE (V)
REJECTION (dB)
REJECTION (dB)
110
105
100
90
80
70
90
5
0
10
15 20 25 30
INPUT VOLTAGE (V)
35
50
40
100
1k
FREQUENCY (Hz)
10
14
300
12
200
150
6
50
2
0
10k
Load Regulation
VIN = 8V
10k
INPUT CURRENT (mA)
–2
–4
0.2
2
4 6 8
SINKING
OUTPUT CURRENT (mA)
10
1236ls8 G07
TJ = 125°C
0.6
0.4
0
TJ = 25°C
0.8
0
0
5
10
15 20 25 30
INPUT VOLTAGE (V)
80
100
Sink Mode Current Limit
TJ = – 55°C
1.0
40
20
0
60
TEMPERATURE (°C)
1236ls8 G06
60
1.2
–3
–5
–10 – 8 – 6 – 4 – 2
SOURCING
5.000
–40 –20
1236ls8 G05
1.4
–1
14
5.002
IOUT = 0
1.6
0
12
5.003
Quiescent Current
3
OUTPUT CHANGE (mV)
100
1k
BANDWIDTH (Hz)
10
1.8
1
10
5.001
1236ls8 G04
2
6
8
TIME (µs)
5.004
8
4
4
4
Output Voltage Temperature Drift
10
100
100
1k
FREQUENCY (Hz)
2
5.005
COUT = 0
FILTER = 1 POLE
fLOW = 0.1Hz
OUTPUT VOLTAGE (V)
350
RMS NOISE (µV)
NOISE VOLTAGE (nV/√Hz)
16
250
0
1236ls8 G03
Output Voltage Noise
Output Voltage Noise Spectrum
10
3
10k
1236ls8 G02
400
5
5
4
1236ls8 G01
0
6
60
CURRENT INTO OUTPUT (mA)
85
VIN = 0V TO 12V
35
40
1236ls8 G08
VIN = 8V
50
40
30
20
10
0
0
2
4
6
8 10 12 14
OUTPUT VOLTAGE (V)
16
18
1236ls8 G09
1236ls8f
4
LT1236LS8
Typical Performance Characteristics
Load Transient Response,
CLOAD = 0
Thermal Regulation
– 0.5
THERMAL
REGULATION*
– 1.0
ILOAD = 10mA
ISOURCE = 0
OUTPUT CHANGE (50mV/DIV)
LOAD
REGULATION
0
ISINK = 0
50mV
50mV
0
20
40 60 80
TIME (ms)
ISINK = 0.2mA
ISOURCE = 0.5mA
ISINK = 2-10mA
ISOURCE = 2-10mA
∆ISOURCE = 100µAP-P
0
100 120 140
1
2
∆ISINK = 100µAP-P
3 4 0
TIME (µs)
1
3
2
4
1236ls8 G11
*INDEPENDENT OF TEMPERATURE COEFFICIENT
1236ls8 G10
Load Transient Response,
CLOAD = 1000pF
Output Noise 0.1Hz to 10Hz
ISINK = 0
20mV
20mV
ISINK = 0.2mA
ISOURCE = 0.2mA
ISINK = 2-10mA
ISOURCE = 2-10mA
∆ISOURCE = 100µAP-P
0
5
FILTERING = 1 ZERO AT ORIGIN
1 POLE AT 0.1Hz
2 POLES AT 10Hz
OUTPUT VOLTAGE NOISE (5µV/DIV)
ISOURCE = 0
OUTPUT CHANGE (20mV/DIV)
OUTPUT CHANGE (mV)
VIN = 25V
∆POWER = 200mW
5µV (1ppm)
∆ISINK = 100µAP-P
10 15 20 0
TIME (µs)
5
10 15 20
1236ls8 G12
0
1
4
3
2
TIME (MINUTES)
5
6
1236ls8 G13
1236ls8f
5
LT1236LS8
Pin Functions
NC (Pins 1, 3, 7, 8): Connected internally, do not connect.
TRIM (Pin 5): Allows adjustment of output voltage. See
Applications Information section for details.
VIN (Pin 2): Power Supply. Bypass with 0.1µF (or larger)
capacitor to ground.
VOUT (Pin 6): Output Voltage. See Applications Information
section for details regarding DC and capacitive loading
and stability.
GND (Pin 4): Device Ground. See Applications Information
section for recommended connection methods.
Block Diagram
INPUT
Q2
R1
OUTPUT
D6
R2
D5
6.3V
+
–
R3
D3
R4
A1
TRIM
D4
Q1
GND
1236sl8 ES
1236ls8f
6
LT1236LS8
Applications Information
Effect of Reference Drift on System Accuracy
A large portion of the temperature drift error budget in
many systems is the system reference voltage. This graph
indicates the maximum temperature coefficient allowable
if the reference is to contribute no more than 0.5LSB error
to the overall system performance. The example shown is
a 12-bit system designed to operate over a temperature
range from 25°C to 65°C. Assuming the system calibration
is performed at 25°C, the temperature span is 40°C. It can
be seen from the graph that the temperature coefficient
of the reference must be no worse than 3ppm/°C if it is
to contribute less than 0.5LSB error. For this reason, the
LT1236LS8 has been optimized for low drift.
MAXIMUM TEMPERATURE COEFFICIENT FOR
0.5LSB ERROR (ppm/°C)
Maximum Allowable Reference Drift
100
8-BIT
10-BIT
10
12-BIT
14-BIT
1.0
LT1236LS8
IN
GND
VOUT
OUT
TRIM
R1
27k
1N4148
R2
50k
1236ls8 AI02
Capacitive Loading and Transient Response
The LT1236LS8 is stable with all capacitive loads, but for
optimum settling with load transients, output capacitance
should be under 1000pF. The output stage of the reference
is class AB with a fairly low idling current. This makes
transient response worst-case at light load currents.
Because of internal current drain on the output, actual
worst-case occurs at ILOAD = 0. Significantly better load
transient response is obtained by moving slightly away
from these points. See Load Transient Response curves
for details. In general, best transient response is obtained
when the output is sourcing current. In critical applications, a 10µF solid tantalum capacitor with several ohms
in series provides optimum output bypass.
Load Regulation
10 20 30 40 50 60 70 80 90 100
TEMPERATURE SPAN (°C)
1236ls8 AI01
Trimming Output Voltage
The LT1236LS8 has an output voltage trim pin, but the
temperature drift of the nominal 4V open circuit voltage
at pin 5 is about –1.7mV/°C. For the voltage trimming not
to affect reference output temperature drift, the external
trim voltage must track the voltage on the trim pin. Input
impedance of the trim pin is about 100kΩ and attenuation to the output is 13:1. The technique shown below
is suggested for trimming the output of the LT1236LS8
while maintaining minimum shift in output temperature
coefficient. The R1/R2 ratio is chosen to minimize interaction of trimming and temperature drift shifts, so the exact
values shown should be used.
The LT1236LS8 is capable of driving 10mA to a load. The
load regulation at the output of the LT1236LS8 is very
good, with a change of less than 25ppm/mA when driving
the load. However, the load current will cause a voltage
drop in the connecting wire between the LT1236LS8 and
the load. This IR drop is dependent on the resistance of
the connecting wire and will appear as additional load
regulation error. For example, 12 feet of #22 gauge wire or
1 foot of 0.025 inch printed circuit board trace will create
2mV loss at 10mA output current. This is equivalent to
1LSB in a 10V, 12-bit system.
There are three approaches that will reduce this effect. First,
limiting the distance between the LT1236LS8 and the load
will reduce the trace length, and improve load regulation.
Second, use wider traces for the connections between
the LT1236LS8 and the load to reduce IR drop. Finally,
1236ls8f
7
LT1236LS8
Applications Information
use a star-ground method, with the LT1236LS8 ground
tied directly to the load, rather than through a ground
plane or other shared ground trace. This last method will
reduce drop in the ground trace between the LT1236LS8
and the load. The ground wire in this case will carry only
approximately 1mA, which is the ground current of the
LT1236LS8, while the load return current will shunt to the
system ground separate from the reference-to-load path.
Series Mode with Boost Transistor
INPUT
R1
220Ω
2N3906
IN
LT1236LS8
OUT
GND
The following circuits show proper hook-up to minimize
errors due to ground loops and line losses. Losses in the
output lead can be greatly reduced by adding a PNP boost
transistor if load currents are 5mA or higher. R2 can be
added to further reduce current in the output sense lead.
Effects of Air Movement on Low Frequency Noise
The LT1236LS8 has very low noise because of the buried
zener used in its design. In the 0.1Hz to 10Hz band, peakto-peak noise is about 0.5ppm of the DC output. To achieve
this low noise, however, care must be taken to shield the
reference from ambient air turbulence. Air movement can
create noise because of thermoelectric differences between
IC package leads and printed circuit board materials and/or
sockets. Power dissipation in the reference, even though it
rarely exceeds 20mW, is enough to cause small temperature gradients in the package leads. Variations in thermal
resistance, caused by uneven air flow, create differential
lead temperatures, thereby causing thermoelectric voltage
noise at the output of the reference.
*OPTIONAL—REDUCES CURRENT IN OUTPUT SENSE
LEAD: R2 = 2.4k
1236ls8 AI04
Long-Term Drift
Long-term drift cannot be extrapolated from accelerated
high temperature testing. This erroneous technique gives
drift numbers that are wildly optimistic. The only way
long-term drift can be determined is to measure it over
the time interval of interest.
The LT1236LS8 long-term drift data was collected on 80
parts that were soldered into printed circuit boards similar
to a real world application. The boards were then placed
into a constant temperature oven with a TA = 35°C, their
outputs were scanned regularly and measured with an 8.5
digit DVM. Typical long-term drift is illustrated in Figure 1.
200
OUT
GND
NORMALIZED TO 10 HOURS
DUE TO SYSTEM WARM-UP
160
120
80
40
KEEP THIS LINE RESISTANCE LOW
+
LOAD
PPM
LT1236LS8
IN
LOAD
GROUND
RETURN
Standard Series Mode
INPUT
R2*
0
–40
–80
–120
GROUND
RETURN
–160
1236ls8 AI03
–200
0
500
1000
HOURS
1500
2000
1236ls8 F01
Figure 1. Long-Term Drift
1236ls8f
8
LT1236LS8
Applications Information
Hysteresis
Thermal hysteresis is a measure of change of output voltage as a result of temperature cycling. Figure 2a and 2b
illustrate the typical hysteresis based on data taken from
the LT1236LS8. A proprietary design technique minimizes
thermal hysteresis.
stresses on the die have changed position. This shift is
similar, but more extreme than thermal hysteresis.
Experimental results of IR reflow shift are shown below
in Figure 4. These results show only shift due to reflow
and not mechanical stress.
300
380s
IR Reflow Shift
22
0
8
12
NUMBER OF UNITS
NUMBER OF UNITS
14
4
2
–50
–30
–10
10
30
50
70
DISTRIBUTION (ppm)
90
1236ls8 F02a
Figure 2a. Hysteresis Plot 0°C to 70°C
40s
0
2
6
4
MINUTES
8
10
1236ls8 F03
Figure 3. Lead-Free Reflow Profile
9
6
tL
130s
RAMP TO
150°C
10
8
T = 150°C
120s
16
10
RAMP
DOWN
tP
30s
75
18
0
150
25°C TO 0°C TO 25°C
25°C TO 70°C TO 25°C
20
TL = 217°C
TS(MAX) = 200°C
TS = 190°C
225
TEMPERATURE (°C)
The mechanical stress of soldering a part to a board can
cause the output voltage to shift. Moreover, the heat of
an IR reflow or convection soldering oven can also cause
the output voltage to shift. The materials that make up a
semiconductor device and its package have different rates
of expansion and contraction. After a part undergoes the
extreme heat of a lead-free IR reflow profile, like the one
shown in Figure 3, the output voltage shifts. After the
device expands, due to the heat, and then contracts, the
TP = 260°C
1× REFLOW
3× REFLOW
24Hr REST
7
6
5
4
3
2
1
0
–0.05 –0.04 –0.03 –0.02 –0.01
REFLOW SHIFT (%)
0
0.01
1236ls8 F04
35
NUMBER OF UNITS
30
Figure 4. Output Voltage Shift Due to IR Reflow
25°C TO –40°C TO 25°C
25°C TO 85°C TO 25°C
Humidity Sensitivity
25
20
15
10
5
0
–120
–80
–40
0
40
80
DISTRIBUTION (ppm)
120
1236ls8 F02b
Figure 2b. Hysteresis Plot –40°C to 85°C
Plastic mold compounds absorb moisture. With changes
in relative humidity, plastic packaging materials change
the amount of pressure they apply to the die inside, which
can cause slight changes in the output of a voltage reference, usually on the order of 100ppm. The LS8 package is
hermetic, so it is not affected by humidity, and is therefore
more stable in environments where humidity may be a
concern. However, PC Board material may absorb moisture
and apply mechanical stress to the LT1236LS8. Proper
board materials and layout are essential.
1236ls8f
9
LT1236LS8
Typical Applications
Boosted Output Current
with Current Limit
Boosted Output Current
with No Current Limit
V + ≥ 9V
V+ ≥ 10V
D1*
LED
R1
220Ω
R1
220Ω
8.2Ω
2N2905
2N2905
IN
IN
LT1236LS8
OUT
GND
+
5V AT
100mA
LT1236LS8
2µF
SOLID
TANT
GND
OUT
+
5V AT
100mA
2µF
SOLID
TANT
1236ls8 TA03
* GLOWS IN CURRENT LIMIT,
DO NOT OMIT
1236ls8 TA04
Handling Higher Load Currents
10V
30mA
IN
LT1236LS8
R1*
169Ω
VOUT
5V
OUT
GND
RL
TYPICAL LOAD
CURRENT = 30mA
*SELECT R1 TO DELIVER TYPICAL LOAD CURRENT.
LT1236 WILL THEN SOURCE OR SINK AS NECESSARY
TO MAINTAIN PROPER OUTPUT. DO NOT REMOVE LOAD
AS OUTPUT WILL BE DRIVEN UNREGULATED HIGH. LINE
REGULATION IS DEGRADED IN THIS APPLICATION
1236ls8 TA05
1236ls8f
10
LT1236LS8
Typical Applications
Operating 5V Reference from 5V Supply
5V LOGIC
SUPPLY
1N914
CMOS LOGIC GATE**
+
fIN ≥ 2kHz*
LT1236LS8
1N914
≈8.5V
IN
+ C2*
C1*
5µF
OUT
GND
5µF
*FOR HIGHER FREQUENCIES C1 AND C2 MAY BE DECREASED
**PARALLEL GATES FOR HIGHER REFERENCE CURRENT LOADING
5V
REFERENCE
1236ls8 TA06
2-Pole Lowpass Filtered Reference
1µF
MYLAR
VIN
–
LT1001
LT1236LS8
VIN
IN
OUT
GND
R1
36k
R2
36k
f = 10Hz
VREF
+
0.5µF
MYLAR
TOTAL NOISE
≤2µVRMS
1Hz ≤ f ≤ 10kHz
–VREF
1236ls8 TA07
1236ls8f
11
LT1236LS8
Typical Applications
High Precision, High Stability, Differential Measurement System
8V TO 12V
5V
LT1236LS8
0.01µF
4.7µF
VCC
R1
5k
C1
0.01µF
–
IN+
+
1/ LTC2051HV
2
IN–
+
R4
5k
C4
0.01µF
–
1/ LTC2051HV
2
R2
10Ω
C2
1µF
BUSY
10µF
15
14
fO
REF+
LTC2440
13
4
0.1µF
SCK
REF–
12
SDO
11
5
CS
IN+
7
6
IN–
SDI
1, 8, 9, 16
10
EXT
R5
10Ω
1236ls8 TA08
C5
1µF
C2, C5 TAIYO YUDEN JMK107BJ105MA
1236ls8f
12
LT1236LS8
Typical Applications
Use Resistor Arrays to Provide Precise Matching in Excitation Amplifier
15V
20Ω
Q1
2N3904
+
1/2
LT1112
1
–
C1
0.1µF
22Ω
5V
3
LT1236LS8
+
C3
47µF
2
C1
0.1µF
RN1
10k
10V
1
8
RN1
10k
350Ω BRIDGE
TWO ELEMENTS
VARYING
5V
7
1
VCC
LTC2411/
LTC2411-1
2
REF +
3
REF –
6
4
–5V
5
4
RN1
10k
3
5
C2
0.1µF
GND
6
20Ω
7
15V
8
–
6
+
5
1/2
LT1112
4
–15V
IN –
6
33Ω
×2
Q2, Q3
2N3906
×2
RN1
10k
IN +
–15V
RN1 IS LT5400ACMS8E-1
1236ls8 TA09
1236ls8f
13
LT1236LS8
Typical Applications
±10V Range Precision Measurement System
VIN1
5V
2
IN
OUT
LT1236LS8
GND
C15
4.7k
5
R20
1k
4
–2.5V
R1
40k
TRIM
REF+
6
5V
3
4
+
6
1
–
REF+
30
–2.5V
REF+
31
REF–
6
R5
8.87k
7
8
5
2
9
LTC2050HV –5V
28
10
VIN2
R6
30k
R9
10k
2.5V
5V
29
R4
5k
R3
5k
C13
0.1µF
–2.5V
R10
7.5k
C14
0.1µF
11
C10
0.1µF
12
13
17
18
21
V+
VCC
CS
LTC2442
SCK
SD0
CH0
CH1
SDI
CH2
BUSY
CH3
FO
COM
EXT
ADCINB
MUOUTA
ADCINA
MUXOUTB
35
1
36
33
2
34
3
–2.5V
27
26
OUTA
–INA
+INA
25
OUTB
–INB
+INB
GND GND GND
4
5
32
19
V–
24
–5V
C9
0.1µF
–2.5V
C17
0.1µF
5V
C8
0.1µF
2.5V
12
13
2
R21
5k
1
5
SDO
3
MMBT3904
SDI
CS
R1, R3, R4 ARE CADDOCK T914
–2.5V
SCK
R22
1.8k
6
11
10
9
74HC4053
X0
X
14
X1
Y0
Y
15
Y1
Z0
Z
4
Z1
INH
A
VCC
5V
B
VEE
–2.5V
C
GND
1236sl8 TA10
1236ls8f
14
LT1236LS8
Package Description
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
LS8 Package
8-Pin Leadless Chip Carrier (5mm × 5mm)
(Reference LTC DWG # 05-08-1852 Rev Ø)
8
2.50 ±0.15
PACKAGE OUTLINE
7
1
6
2
2.54 ±0.15
5
3
1.50 ±0.15
4
0.70 ±0.05
5.00 SQ ±0.15
5.80 SQ ±0.15
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
5.00 SQ ±0.15
1.45 ±0.10
0.95 ±0.10
4.20 SQ ±0.10
8
1
PIN 1
TOP MARK
(SEE NOTE 5)
R0.20 REF
8
2.00 REF
7
2
6
3
5
1
7
4.20 ±0.10
R0.20 REF
6
2
2.54 ±0.15
5
3
1.00 TYP
4
LS8 0609 REV Ø
4
0.70 TYP
NOTE:
1. ALL DIMENSIONS ARE IN MILLIMETERS
2. DRAWING NOT TO SCALE
3. DIMENSIONS PACKAGE DO NOT INCLUDE PLATING BURRS
PLATING BURRS, IF PRESENT, SHALL NOT EXCEED 0.30mm ON ANY SIDE
4. PLATING—ELECTO NICKEL MIN 1.25UM, ELECTRO GOLD MIN 0.30UM
5. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
0.10 TYP
0.64 TYP
1236ls8f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
15
LT1236LS8
Typical Application
Measure DC to Daylight Using the LTC2408 and LT1236LS8
GUARD RING
5V
ELECTROMETER
INPUT
(pH, PIEZO)
3
7
+
2
–
R5
5k, 1%
6
LT1793
DC
VOLTMETER
INPUT
1mV TO 1000V
4
–5V
R2
4.7k
0.1%
0V TO 5V
–60mV TO 4V
R3, 10k
C1, 0.1µF
6
5V
REF
+
R4
1k
R1
900k
0.1%, 1W, 1000 WVDC
5V
MAX
10µF
+
LT1236LS8
OUT IN
GND
4
3-WIRE R-PACK
60Hz
+
AC
INPUT
R6
10k, 0.1%
100µF
5V
5V
2
RT
3
7
–
IN914
+
R9
1k
1%
IN914
6
LTC1050
R10
5k
1%
R8
100Ω, 5%
4
20mV TO 80mV
–5V
R11
24.9k, 0.1% V
REF
5V
50Ω
8V
+
R7
10k, 0.1%
1µF
60Hz–RF
RF POWER
2
100Ω
Pt RTD
(3-WIRE)
9
CH0
10
CH1
11
CH2
12
CH3
13
CH4
14
CH5
15
CH6
17
CH7
3
2, 8
VREF VCC
24-BIT
∆∑ ADC
INFRARED
THERMOCOUPLE
20
19, 25
21
FO
MPU
24
26
INTERNAL OSC
SELECTED FOR
60Hz REJECTION
1236sl8 TA11
–2.2mV to 16mV
0V to 4V
5V
DAYLIGHT
HAMAMATSU
PHOTODIODE
S1336-5BK
OMEGA
0S36-01
INFRARED
DIN
SERIAL DATA LINK
MICROWIRE AND
SPI COMPATABLE
23
LTC2408
2.7V AT 0°C
0.9V AT 40°C
R12
24.9k, 0.1% V
REF
5V
THERMISTOR
10k NTC
CLK
SDO
1, 5, 6, 16, 18, 22, 27, 28
LOCAL
TEMP
1µF
CSMUX
8-CHANNEL
MUX
GND
FORCE SENSE
J3
4
ADCIN
CSADC
<1mV
J1
J2
50Ω LOAD
BONDED TO
RTD ON
INSULATED
MOUNTING
7
MUXOUT
R13
5k
0.1%
Related Parts
PART NUMBER DESCRIPTION
COMMENTS
LT1021
Precision References for Series or Shunt Operation in
Hermetic TO-5, SOP-8, DIP-8 Package
0.05% Max Initial Error, 5ppm/°C Max Drift, 1ppm Peak-to-Peak Noise
(0.1Hz to 10Hz), –55°C to 125°C (TO-5)
LT1236S8/
LT1236N8
Low Drift, Low Noise, 5V and 10V Voltage Reference in
SO8, and DIP8 Package
0.05% Max Initial Error, 5ppm/°C Max Drift, 1ppm Peak-to-Peak Noise
(0.1Hz to 10Hz), –40°C to 85°C
LTC6652LS8
High Precision, Buffered Voltage Reference Family in
5mm × 5mm Hermetic QFN Package
0.05% Max Initial Error, 5ppm/°C Max Drift, Shutdown Current <2µA,
–40°C to 125°C Operation
LT6654LS8
Precision, Low Noise, High Output Drive Voltage Reference 1.6ppm Peak-to-Peak Noise (0.1Hz to 10Hz, Sink/Source ±10mA, 5ppm/°C
Family in 5mm × 5mm Hermetic QFN Package
Max Drift, –40°C to 125°C Operation
1236ls8f
16 Linear Technology Corporation
LT 0812 • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
 LINEAR TECHNOLOGY CORPORATION 2012
Similar pages