GP1001 THRU GP1007 10.0 AMPS. Glass Passivated Rectifiers Voltage Range 50 to 1000 Volts Current 10.0 Amperes TO-220 Features Low forward voltage drop High current capability High reliability High surge current capability Mechanical Data Cases: TO-220 molded plastic Epoxy: UL 94V-0 rate flame retardant Terminals: Leads solderable per MIL-STD202, Method 208 guaranteed Polarity: As marked High temperature soldering guaranteed: 260℃/10 seconds .16”,(4.06mm) from case. Weight: 2.24 grams PIN 1 PIN 3 Positive CT CASE PIN 2 Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol GP GP Type Number 1001 1002 50 100 Maximum Recurrent Peak Reverse Voltage VRRM 35 70 Maximum RMS Voltage VRMS 50 100 Maximum DC Blocking Voltage VDC Maximum Average Forward Rectified Current .375”(9.5mm) Lead Length @TC = 100℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @5.0A Maximum DC Reverse Current @ TC=25℃ at Rated DC Blocking Voltage Typical Junction Capacitance ( Note 1) GP GP GP GP GP Units 1003 1004 1005 1006 1007 200 140 200 400 280 400 600 420 600 800 1000 560 700 800 1000 V V V I(AV) 10.0 A IFSM 125 A VF 1.1 V IR 5.0 uA 30 pF 3.0 ℃/W - 65 to + 150 Operating and Storage Temperature Range TJ ,TSTG ℃ Notes: 1. Measured at 1 MHz and Applied Reverse Voltage of 4.0 Volts D.C. 2. Thermal Resistance from Junction to Case Mounted on Heatsink size 2” x 3” x 0.25” Al-Plate Typical Thermal Resistance (Note 2) Cj RθJC - 488 - RATINGS AND CHARACTERISTIC CURVES (GP1001 THRU GP1007) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE FIG.2- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 175 PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD CURRENT. (A) 12 10 8 Single Phase Half Wave 60Hz Resistive of Inductive Load 6 4 2 150 125 100 8.3ms Single Half Sine Wave JEDEC Method 75 50 25 0 0 50 100 1 150 2 5 o CASE TEMPERATURE. ( C) 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.3- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG FIG.4- TYPICAL REVERSE CHARACTERISTICS PER LEG 400 100 200 INSTANTANEOUS REVERSE CURRENT. ( A) 40 40 20 10 4 2 1 Tj=25oC Pulse Width=300 s 1% Duty Cycle 0.4 0.2 0.1 10 Tj=125 0C 4 2 1.0 Tj=25 0C .4 .2 .6 .8 1.0 1.2 1.4 1.6 1.8 .1 2.0 FORWARD VOLTAGE. (V) 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.5- TYPICAL JUNCTION CAPACITANCE 120 JUNCTION CAPACITANCE.(pF) INSTANTANEOUS FORWARD CURRENT. (A) 100 100 80 60 40 f=10 MHz Vsig 50Mvp-p Tj=25 0C 20 0 0.1 0.5 1.0 4 10 40 REVERSE VOLTAGE. (V) - 489 - 100 400 1000