OPTEK OPF507 Fiber optic receiver Datasheet

Fiber Optic Receiver
OPF500 Series
OPF500 Series
•
•
•
•
•
Interfaces with all logic circuits
Two output options
Optimized for fiber optic applications using 50 to 200 micron fibers
Data rate to 200kbps NRZ
Available with multiple packaging options
The OPF500 series receiver contains a monolithic integrated circuit which incorporates a photodiode, linear amplifier, a voltage regulator, and a Schmitt trigger on a single silicon chip. These receivers are designed for short haul
fiber optic systems using 850 nm LEDs such as Optek’s OPF300 series.
These devices feature TTL/LSTTL compatible logic level output. An internal voltage regulator allows operation
with supply voltages ranging from 4.5V to 16V.
Applications
♦
♦
♦
♦
Industrial Ethernet equipment
Copper-to-fiber media conversion
Intra-system fiber optic links
Video surveillance systems
Part Ordering Information
Part Number
Description
OPF500
Buffer, 10kW Pull-Up
Plastic Cap Component
OPF505
Buffer, 10kW Pull-Up
Metal Can Component
OPF507
Buffer, 10kW Pull-Up
Metal ST Receptacle
OPF510
Inverter, 10kW Pull-Up
Plastic Cap Component
OPF512
Inverter, 10kW Pull-Up
Metal ST Receptacle
This component is susceptible to damage from electrostatic discharge (ESD).
Normal static precautions should be
taken in handling and assembly of this
component to prevent ESD damage or
degradation.
RoHS
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc.— 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (800) 341-4747 FAX: (972) 323– 2396 [email protected] www.optekinc.com
Issue A
05/2013
Page 1 of 5
Fiber Optic Receiver
OPF500 Series
Absolute Maximum Ratings
Storage Temperature
-65° C to +100° C
Operating Temperature
-40° C to +85° C
Lead Soldering Temperature (for 10 seconds)
260° C
Supply Voltage
18 V
Sinking Current
16 mA
Power Dissipation
200 mW
Open Collector Power Distribution
40mW
Voltage at Output
30 V
Electrical/Optical Characteristics
4.5 V ≤ VCC ≤ 16.0 V, TA = 25°C — unless otherwise specified
SYMBOL
PARAMETER
VCC
Supply Voltage
VOH
High Level Output Voltage
VOL
Low Level Output Voltage
ICC
Supply Current
PIN
MIN
TYP
4.5
MAX
UNITS
16.0
V
CONDITIONS
V
Buffer: PIN > 2.0 µW
Inverter: PIN < 0.1 µW
0.4
V
Buffer: PIN < 0.1 µW
Inverter: PIN > 2.0 µW
12.0
mA
No output load
Input Sensitivity
2.0
µW
λp = 850 nm
Rise Time
300
100
ns
Buffer
Inverter
tf
Fall Time
300
100
ns
Inverter
Buffer
BW
Bandwidth
tr
PWD
Pulse Width Distortion
RoHS
Issue A
05/2013
Page 2 of 5
VCC - 1.5
5.0
100
kHz
±10
%
PIN = 1.5 µW (peak)
VCC = 5.0 V
PIN > 2.0 µW, 50% duty cycle
1 µW < PIN < 100 µW, f = 20 kHz
50% duty cycle
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc.— 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (800) 341-4747 FAX: (972) 323– 2396 [email protected] www.optekinc.com
Fiber Optic Receiver
OPF500 Series
Mechanical Outline — OPF500, OPF510
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc.— 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (800) 341-4747 FAX: (972) 323– 2396 [email protected] www.optekinc.com
Issue A
05/2013
Page 3 of 5
Fiber Optic Receiver
OPF500 Series
Mechanical Outline — OPF505
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue A
05/2013
Page 4 of 5
OPTEK Technology Inc.— 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (800) 341-4747 FAX: (972) 323– 2396 [email protected] www.optekinc.com
Fiber Optic Receiver
OPF500 Series
Mechanical Outline — OPF507, OPF512
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc.— 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (800) 341-4747 FAX: (972) 323– 2396 [email protected] www.optekinc.com
Issue A
05/2013
Page 5 of 5
Similar pages