Hittite HMC737LP4E Mmic vco w/ half frequency output Datasheet

HMC737LP4 / 737LP4E
v01.0209
MMIC VCO w/ HALF FREQUENCY OUTPUT
14.9 - 15.5 GHz
Typical Applications
Features
The HMC737LP4(E) is ideal for:
Dual Output: Fo = 14.9 - 15.5 GHz
Fo/2 = 7.45 - 7.75 GHz
• Point to Point/Multipoint Radio
• Test Equipment & Industrial Controls
Pout: +9 dBm
Phase Noise: -105 dBc/Hz @ 100 kHz
• SATCOM
No External Resonator Needed
• Military End-Use
24 Lead 4x4mm SMT Package: 16mm2
Functional Diagram
The HMC737LP4(E) is a GaAs InGaP Heterojunction
Bipolar Transistor (HBT) MMIC VCO. The
HMC737LP4(E) integrate a resonator, negative
resistance device, varactor diode and feature half
frequency output. The VCO’s phase noise performance
is excellent over temperature, shock, and process due
to the oscillator’s monolithic structure. Power output
is +9 dBm typical from a +4.2V supply voltage. The
voltage controlled oscillator is packaged in a leadless
QFN 4x4 mm surface mount package, and requires no
external matching components.
VCOS with Fo/2 OUTPUT - SMT
8
8-1
General Description
Electrical Specifications, TA = +25° C, Vcc = +4.2V
Parameter
Frequency Range
Power Output
Min.
Fo
Fo/2
Max.
14.9 - 15.5
7.45 - 7.75
RFOUT
RFOUT/2
6
-8
Vtune
1
SSB Phase Noise @ 100 kHz Offset, Vtune= +5V @ RFOUT
Tune Voltage
Typ.
9
-3
GHz
GHz
13
2
-105
Supply Current
120
150
Tune Port Leakage Current (Vtune= 13V)
Output Return Loss
Units
dBm
dBm
dBc/Hz
13
V
180
mA
10
µA
2.5
dB
-45
-42
dBc
dBc
Pulling (into a 2.0:1 VSWR)
12
MHz pp
Pushing @ Vtune= 5V
24
MHz/V
Frequency Drift Rate
1.2
MHz/°C
Harmonics/Subharmonics
1/2
3/2
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC737LP4 / 737LP4E
v01.0209
MMIC VCO w/ HALF FREQUENCY OUTPUT
14.9 - 15.5 GHz
Frequency vs. Tuning Voltage, T= 25°C
17
17
16
16
FREQUENCY (GHz)
15
14
+25 C
+85 C
-40 C
13
15
14
Vcc = 4.0V
Vcc = 4.2V
Vcc = 4.4V
13
12
12
0
1
2
3
4
5
6
7
8
9
10
11 12
13
0
1
2
3
TUNING VOLTAGE (VOLTS)
Sensitivity vs. Tuning Voltage, Vcc = +4.2V
6
7
8
9
10
11 12
13
14
500
OUTPUT POWER (dBm)
SENSITIVITY (MHz/VOLT)
5
Output Power
vs. Tuning Voltage, Vcc = +4.2V
600
+25 C
+85 C
-40 C
400
300
200
100
0
8
12
10
8
+25 C
+85 C
-40 C
6
4
0
1
2
3
4
5
6
7
8
9
10
11 12
13
0
TUNING VOLTAGE (VOLTS)
-70
-50
SSB PHASE NOISE (dBc/Hz)
-30
-80
-90
10kHz offset
100kHz offset
-110
-120
0
1
2
3
4
5
6
7
8
9
TUNING VOLTAGE (VOLTS)
2
3
4
5
6
7
8
9
10
11 12
13
SSB Phase Noise @ Vtune = +5V
-60
-100
1
TUNING VOLTAGE (VOLTS)
SSB Phase Noise vs. Tuning Voltage
SSB PHASE NOISE(dBc/Hz)
4
TUNING VOLTAGE (VOLTS)
10
11 12
13
+25 C
+85 C
-40 C
-70
-90
-110
-130
-150
3
10
4
10
5
6
10
10
OFFSET FREQUENCY (Hz)
VCOS with Fo/2 OUTPUT - SMT
FREQUENCY (GHz)
Frequency vs. Tuning Voltage, Vcc = +4.2V
7
10
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
8-2
HMC737LP4 / 737LP4E
v01.0209
MMIC VCO w/ HALF FREQUENCY OUTPUT
14.9 - 15.5 GHz
RFOUT/2 Output Power
vs. Tuning Voltage, Vcc = +4.2V
9
0
8.5
-1
OUTPUT POWER (dBm)
FREQUENCY (GHz)
RFOUT/2 Frequency
vs. Tuning Voltage, Vcc = +4.2V
8
7.5
+25 C
+85 C
-40 C
7
6.5
+25 C
+85 C
-40 C
-2
-3
-4
-5
6
-6
0
1
2
3
4
5
6
7
8
9
10
11 12
13
0
1
2
3
TUNING VOLTAGE (VOLTS)
Absolute Maximum Ratings
VCOS with Fo/2 OUTPUT - SMT
8
8-3
4
5
6
7
8
9
10
11 12
13
TUNING VOLTAGE (VOLTS)
Typical Supply Current vs. Vcc
Vcc
+5.5V
Vtune
0 to 15V
Vcc (V)
4.0
Icc (mA)
140
Junction Temperature
135 °C
4.2
150
Continuous Pdiss (T=85 °C)
(derate 19.6 mW/C above 85 °C
1W
4.4
160
Thermal Resistance
(junction to ground paddle)
51 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
Note: VCO will operate over full voltage range shown above.
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Package Information
MSL Rating
Package Marking [3]
Part Number
Package Body Material
Lead Finish
HMC737LP4
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
[1]
H737
XXXX
HMC737LP4E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
[2]
H737
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC737LP4 / 737LP4E
v01.0209
MMIC VCO w/ HALF FREQUENCY OUTPUT
14.9 - 15.5 GHz
Outline Drawing
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
8
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN.
Application Circuit
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
VCOS with Fo/2 OUTPUT - SMT
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
8-4
HMC737LP4 / 737LP4E
v01.0209
MMIC VCO w/ HALF FREQUENCY OUTPUT
14.9 - 15.5 GHz
Pin Descriptions
Pin Number
VCOS with Fo/2 OUTPUT - SMT
8
8-5
Function
Description
1 - 9, 11 - 14, 18,
19, 21, 23, 24
N/C
No Connection. These pins may be connected to RF/DC
ground. Performance will not be affected.
10
RFOUT/2
Half frequency output (AC coupled).
Requires external AC coupling capacitors.
16
RFOUT
RF output (AC coupled).
20
Vcc
Supply Voltage, +4.2V
22
VTUNE
Control voltage and modulation input. Modulation
bandwidth dependent on drive source impedance.
See “Determining the FM Bandwidth of a Wideband
Varactor Tuned VCO” application note.
15, 17,
Paddle
GND
Package bottom has an exposed metal paddle that
must be connected to RF/DC ground.
Interface Schematic
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC737LP4 / 737LP4E
v01.0209
MMIC VCO w/ HALF FREQUENCY OUTPUT
14.9 - 15.5 GHz
Evaluation PCB
List of Materials for Evaluation PCB 123987 [1]
Item
Description
J1 - J3
PCB Mount SMA RF Connector
J4
2 mm DC Header
C1, C2
100 pF Capacitor, 0402 Pkg.
C3
4.7 µF Tantalum Capacitor
U1
HMC737LP4(E) VCO
PCB [2]
124532 Eval Board
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350 or Arlon 25FR
The circuit board used in the application should
use RF circuit design techniques. Signal lines
should have 50 Ohm impedance while the package
ground leads and backside ground paddle should
be connected directly to the ground plane similar to
that shown. A sufficient number of via holes should
be used to connect the top and bottom ground
planes. The evaluation circuit board shown is available from Hittite upon request.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
VCOS with Fo/2 OUTPUT - SMT
8
8-6
Similar pages