Diodes AP1084T25L-U 5a low dropout positive adjustable or fixed-mode regulator Datasheet

AP1084
5A LOW DROPOUT POSITIVE ADJUSTABLE OR
FIXED-MODE REGULATOR
General Description
Features
•
•
•
•
•
•
•
•
•
AP1084 is a low dropout positive adjustable or fixed-mode
regulator with 5.0A output current capability. The product is
specifically designed to provide well-regulated supply for low
voltage IC applications such as high-speed bus termination and
low current 3.3V logic supply. AP1084 is also well suited for other
applications such as VGA cards. AP1084 is guaranteed to have
lower than 1.4V dropout at full load current making it ideal to
provide well-regulated outputs of 1.25 to 3.3V with 4.7 to 12V
input supply.
1.4V Maximum Dropout at Full Load Current
Built-in Thermal Shutdown
Output Current Limiting
Adjustable Output Voltage or Fixed 1.5V, 1.8V, 2.5V,
3.3V, 5.0V
Fast Transient Response
Good Noise Rejection
Lead-Free Package: TO252-3L, TO263-3L, and
TO220-3L
TO252-3L: Available in “Green” Molding Compound
(No Br, Sb) (Note 1)
Lead Free Finish/RoHS Compliant for Lead Free
products (Note 2)
Ordering Information
AP1084 X
Note:
Package
Vout
D : TO252-3L
K : TO263-3L
T : TO220-3L
Blank : Adj
15 = 1.5V
18 = 1.8V
25 = 2.5V
33 = 3.3V
50 = 5.0V
X
X
Lead Free
Packing
L : Lead Free
G : Green (Note 1)
-U : Tube
-13 : Taping
1. Green is only available for TO252-3L.
2. RoHS revision 13.2.2003. Glass and High Temperature Solder Exemptions Applied, see EU Directive Annex Notes 5 and 7.
Device
Lead-free
Lead-free
Note:
XX
AP1084D
AP1084K
AP1084T
Tube/Bulk
Package Packaging
Part Number
Code
(Note 3) Quantity
Suffix
D
K
T
TO252-3L
TO263-3L
TO220-3L
80
50
50
-U
-U
-U
13” Tape and Reel
Part Number
Quantity
Suffix
2500/Tape & Reel
800/Tape & Reel
NA
-13
-13
NA
3. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at
http://www.diodes.com/datasheets/ap02001.pdf.
AP1084 Rev. 1
1 of 10
www.diodes.com
FEBRUARY 2007
© Diodes Incorporated
AP1084
5A LOW DROPOUT POSITIVE ADJUSTABLE OR
FIXED-MODE REGULATOR
Block Diagram
Vin
3
2
Vout
1
Adj
+
+
-
1.25V
+
CURRENT
LIMIT
+
-
Thermal
Shutdown
Pin Assignment
TO263-3L
TO252-3L
FRONT VIEW
FRONT VIEW
2
1
Vin
3
Vin
3
2
Vout
Adj ( GND)
Tab is Vout
1
Vout
Adj ( GND)
Tab is Vout
TO220-3L
FRONT VIEW
3
Vin
2
Vout
1
Adj ( GND)
Tab is Vout
AP1084 Rev. 1
2 of 10
www.diodes.com
FEBRUARY 2007
© Diodes Incorporated
AP1084
5A LOW DROPOUT POSITIVE ADJUSTABLE OR
FIXED-MODE REGULATOR
Pin Description
Function
Name
I/O
TO263/
252/220
Adj
(GND)
I
1
Vout
O
2
Vin
I
3
Adjustable (Ground only for fixed mode)
A resistor divider from this pin to the Vout pin and ground sets the
output voltage (Ground only for Fixed-Mode).
The output of the regulator. A minimum of 10uF (0.15Ω ≤ ESR ≤
20Ω) capacitor must be connected from this pin to ground to
insure stability.
The input pin of regulator. Typically a large storage capacitor
(0.15Ω ≤ ESR ≤ 20Ω) is connected from this pin to ground to insure
that the input voltage does not sag below the minimum dropout
voltage during the load transient response. This pin must always be
1.4V (1.3V) higher than Vout in order for the device to regulate
properly.
Absolute Maximum Ratings
Symbol
Parameter
Vin
TST
DC Supply Voltage
Storage Temperature
TOP
Operating Junction Temperature Range
TM
Maximum Junction Temperature
AP1084 Rev. 1
3 of 10
www.diodes.com
Rating
Unit
-0.3 to 12
-65 to +150
0 to +125
V
oC
oC
150
oC
FEBRUARY 2007
© Diodes Incorporated
AP1084
5A LOW DROPOUT POSITIVE ADJUSTABLE OR
FIXED-MODE REGULATOR
Electrical Characteristics
Sym.
Parameter
(Under Operating Conditions)
Conditions
o
VREF
Reference Voltage Io = 10mA, TA = 25 C, (Vin-Vout) = 1.5V
AP1084-XXX
IO = 10mA, VOUT+1.5V<VIN<12V, TA = 25oC
IOUT = 10mA, TA = 25oC, 3V≦VIN≦12V
AP1084-1.5
Line AP1084-1.8
IOUT = 10mA, TA = 25oC, 3.3V≦VIN≦12V
Regula
IOUT = 10mA, TA = 25oC, 4V≦VIN≦12V
AP1084-2.5
tion
IOUT = 10mA, TA = 25oC, 4.8V≦VIN≦12V
AP1084-3.3
IOUT = 10mA, TA = 25oC, 6.5V≦VIN≦12V
AP1084-5.0
VIN = 3.3V, 0mA<Io<5A, TA = 25oC
AP1084-Adj
C
VIN = 3V, 0mA<Io<5A, TA = 25oC
AP1084-1.5
(Note 4, 5)
VIN = 3.3V, 0mA<Io<5A
Load AP1084-1.8
o
TA = 25 C (Note 4, 5)
Regula
VIN = 4V, 0mA < Io < 5A
tion
AP1084-2.5
o
TA = 25 C (Note 4, 5)
VIN = 5V, 0mA < Io < 5A, TA = 25oC
AP1084-3.3
(Note 4, 5)
VIN = 8V, 0mA < Io < 5A, TA = 25oC
AP1084-5.0
(Note 4, 5)
∆Vo Dropout Voltage
Io = 5.0A (∆Vout = 1% Vout)
Current Limit
Vin-Vout = 5V
Minimum Load
Current
Temperature
Io = 10mA
Stability
Thermal Resistance
TO252-3L
Junction-to-Ambient
TO263-3L
θJA
(No heat sink; No
TO220-3L
air flow)
TO252-3L: Control Circuitry/Power Transistor
Thermal Resistance
θJC
TO263-3L: Control Circuitry/Power Transistor
Junction-to-Case
TO220-3L: Control Circuitry/Power Transistor
Note:
Min.
Typ.
Max.
Unit
1.225
1.250
1.470
1.764
2.450
3.235
4.900
1.500
1.800
2.500
3.300
5.000
1.275
0.2
1.530
1.836
2.550
3.365
5.100
V
%
V
V
V
V
V
1
%
12
15
mV
15
18
mV
20
25
mV
26
33
mV
40
50
mV
1.3
1.4
V
A
5
10
mA
5.1
0.5
98
95
83
10
19
13
%
O
C/W
O
C/W
4. See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant
junction temperature by low duty cycle pulse testing. Load regulation is measured at the output lead = 1/18” from the package.
5. Line and load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the difference between
input and output and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range.
AP1084 Rev. 1
4 of 10
www.diodes.com
FEBRUARY 2007
© Diodes Incorporated
AP1084
5A LOW DROPOUT POSITIVE ADJUSTABLE OR
FIXED-MODE REGULATOR
Typical Circuit
(1) TO263/252/220
5.0V to 3.3V Fixed Mode Regulator
Adjustable Regulator
5V
5V
C1
100uF
C1
100uF
Vin
Vin
Vout
GND
Tab is Vout
2.5V/5A
Vout
3.3V/5A
C2
100uF
Adj
R1 121Ω
R2 121Ω
Tab is Vout
Note: VO = VREF∗ (1 +
AP1084 Rev. 1
C2
100uF
5 of 10
www.diodes.com
R2
R1
)
FEBRUARY 2007
© Diodes Incorporated
AP1084
5A LOW DROPOUT POSITIVE ADJUSTABLE OR
FIXED-MODE REGULATOR
Functional Description
Introduction
The AP1084 adjustable Low Dropout (LDO) regulator is a 3 terminal device that can easily be programmed with the addition of two
external resistors to any voltages within the range of 1.25V to Vin-1.4V. The AP1084 only needs 1.4V differential between Vin and Vout to
maintain output regulation. In addition, the output voltage tolerances are also extremely tight and they include the transient response as
part of the specification. For example, Intel VRE specification calls for a total of +/- 100mV including initial tolerance, load regulation and 0
to 5.0A load step.
The AP1084 is specifically designed to meet the fast current transient needs as well as providing an accurate initial voltage,
reducing the overall system cost with the need for fewer output capacitors.
Output Voltage Setting
The AP1084 can be programmed to any voltages in the range of 1.25V to Vin-1.4V with the addition of R1 and R2 external resistors
according to the following formula:
Vout = Vref (1+ R2/R1) +Iadj *R2 , where Vref = 1.25 typically, Iadj =
55uA typically R1 & R2 as shown below:
Vin
AP1084
Adj
Vout
Vref
Iadj = 55uA
R1
R2
The AP1084 keeps a constant 1.25V between the output pin and the adjust pin. By placing a resistor R1 across these two pins a
constant current flows through R1, adding to the Iadj current and into the R2 resistor producing a voltage equal to the
(1.25/R1)*R2+Iadj*R2 which will be added to the 1.25V to set the output voltage. This is summarized in the above equation. Since the
minimum load current requirement of the AP1084 is 10mA, R1 is typically selected to be 121Ω resistor so that it automatically satisfies
the minimum current requirement. Notice that since Iadj is typically in the range of 55uA it only adds a small error to the output voltage
and should only be considered when a very precise output voltage setting is required. For example, in a typical 3.3V application where
R1=121Ω and R2=200Ω the error due to Iadj is only 0.3% of the nominal set point.
Load Regulation
Since the AP1084 is only a 3 terminal device, it is not possible to provide true remote sensing of the output voltage at the load. The
best load regulation is achieved when the bottom side of R2 is connected to the load and the top-side of R1 resistor is connected directly
to the case or the Vout pin of the regulator and not to the load. It is important to note that for high current applications, this can re-present a
significant percentage of the overall load regulation and one must keep the path from the regulator to the load as short as possible to
minimize this effect.
Stability
The AP1084 requires the use of an output capacitor as part of the frequency compensation in order to make the regulator stable.
For most applications a minimum of 10uF aluminum electrolytic capacitor insures both stability and good transient response.
Thermal Design
The AP1084 incorporates an internal thermal shutdown that protects the device when the junction temperature exceeds the
o
maximum allowable junction temperature. Although this device can operate with junction temperatures in the range of 150 C, it is
recommended that the selected heat sink be chosen such that during maximum continuous load operation the junction temperature is
kept below that temperature.
Layout Consideration
The output capacitors must be located as close to the Vout terminal of the device as possible. It is recommended to use a section of
a layer of the PC board as a plane to connect the Vout pin to the output capacitors to prevent any high frequency oscillation that may
result due to excessive trace inductance.
AP1084 Rev. 1
6 of 10
www.diodes.com
FEBRUARY 2007
© Diodes Incorporated
AP1084
5A LOW DROPOUT POSITIVE ADJUSTABLE OR
FIXED-MODE REGULATOR
Performance Characteristics
0.20
2. 0
Output Voltage Deviation (%)
1. 8
1. 6
Dropout Voltage (V)
1. 4
1. 2
0
I load=1.5A
-0.20
Tj = 25 oC
1. 0
-0.40
0. 8
Tj = 125 oC
0. 6
-0.80
0. 4
0. 2
0
0
1
2
3
Output Current (A)
-1
5
4
-25
Dropout Voltage vs Output Current
0
25
50
Temperature ( oC)
75
100
125
Load Regulation vs Temperature
2
1
0.8
1
0. 5
0
-0.5
-1
-1.5
-2
-50
-25
0
25
50
Temperature ( oC)
75
100
125
150
Output Voltage Deviation (%)
Output Voltage Change (%)
1.5
0.6
0.4
0.2
0
2
4
7.5
Cin=1uF
Cout=10uF Tantalum
6.5
5.5
40
20
0
-20
-40
0
20
40
60
80
100 120 140 160 180 200
TIME (us)
Load Current (A) Output Voltage Deviation (mV)
Output Voltage Deviation (mV) Input Voltage (V)
Percent Change in Output Voltage vs Temperature
8
10
12
Line Regulation
60
Cin=1uF
Cout=10uF Tantalum
Preload=100mA
40
20
0
-20
-40
6
4
2
0
Line Transient Response
AP1084 Rev. 1
6
Input Voltage (V)
0
10
20
30
40
50
TIME (us)
60
70
80
90
100
Load Transient Response
7 of 10
www.diodes.com
FEBRUARY 2007
© Diodes Incorporated
AP1084
5A LOW DROPOUT POSITIVE ADJUSTABLE OR
FIXED-MODE REGULATOR
Marking Information
(1) TO252-3L
(Top view)
Logo
84-VV
YY WW X X
Internal Code
Xth Week: 01~52
Year: "01" = 2001
"02" = 2002
~
Part Number
1084 for ADJ
84-VV:15 for 1.5V
18 for 1.8V
25 for 2.5V
33 for 3.3V
50 for 5.5V
L : Lead Free
G : Green
(2) TO220-3L / TO263-3L
( Top view )
Logo
Part Number
VV: 15 for 1.5V
18 for 1.8V
25 for 2.5V
33 for 3.3V
50 for 5V
Blank for ADJ
AP1084 Rev. 1
1084-VV
YY WW X X
8 of 10
www.diodes.com
L : Lead Free
Internal code
Xth week: 01~52
Year: "01" = 2001
"02" = 2002
FEBRUARY 2007
© Diodes Incorporated
AP1084
5A LOW DROPOUT POSITIVE ADJUSTABLE OR
FIXED-MODE REGULATOR
Package Information
(unit: mm)
2.92
Typ 1.30
(1) TO263-3L
2.5 4
BSC.
1.27/
1.78
Typ
1.52
3
15.7
9.1
8.65/9.65 Typ 9.15
10.9
14.61/15.88 Typ 15.24
9.65/10.29 Typ 9 .9 7
2.54
1.3
0 .51/0.99 Typ 0 .75
Land P attern R ecom m endation (U nit: m m )
0.38 Typ
4.06/4.83
Typ 4.45
1.14/1.40 T yp1.27
1.14/1.40
Typ 1.27
2.28/2.80 Typ 2 .54
6.354/6.80 Typ 6.58
5.6
7.2
11.0
2.25
2.0
5.40/6.20
Typ 5.57
5.6
5.20/5.50 Typ 5.35
0.88/1.27
(2) TO252-3L
1.2
2.28
BSC.
4.57 BSC.
0.64/1.02
Typ 0.83
0.45/0.58
Typ 0.52
AP1084 Rev. 1
Land Pattern Recommendation (Unit: mm)
0.89/
1.14
9.00/10.40 Typ 9.70
0.51
9 of 10
www.diodes.com
SEE NOTE2
0.61 Typ
SEATING
PLANE
2.18/2.40
Typ 2.29
0.45/0.58
Typ 0.52
FEBRUARY 2007
© Diodes Incorporated
AP1084
5A LOW DROPOUT POSITIVE ADJUSTABLE OR
FIXED-MODE REGULATOR
Package Information
(Continued)
(3) TO220-3L
∅ 3.53/4.09
3.55/4.85
Typ 4.20
Typ 3.81
5.84/6.86
Typ 6.35
4.83/5.33
Typ 5.08
12.72/14.72
Typ 13.72
3.66/6.35
Typ 5.00
1.14/1.78
Typ 1.46
0.51/1.40
Typ 0.95
SEATING PLANE
9.70/10.70
Typ 10.20
14.20/16.50
Typ 15.35
2.54/3.43
Typ 2.98
0.31/1.14
0.51/1.14
Typ 0.72
Typ 0.83
2.99/2.79
Typ 2.54
2.03/2.92
Typ 2.48
IMPORTANT NOTICE
Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further
notice to any product herein. Diodes Incorporated does not assume any liability arising out of the application or use of any product described herein; neither
does it convey any license under its patent rights, nor the rights of others. The user of products in such applications shall assume all risks of such use and will
agree to hold Diodes Incorporated and all the companies whose products are represented on our website, harmless against all damages.
LIFE SUPPORT
Diodes Incorporated products are not authorized for use as critical components in life support devices or systems without the expressed written approval of the
President of Diodes Incorporated.
AP1084 Rev. 1
10 of 10
www.diodes.com
FEBRUARY 2007
© Diodes Incorporated
Similar pages