MORNSUN IB0509LT-1W Single output smd dc-dc converter Datasheet

IB_LD-1W & IB_LS-1W Series
1W, FIXED INPUT, ISOLATED & REGULATED
SINGLE OUTPUT DC-DC CONVERTER
multi-country patent protection
FEATURES
RoHS
PRODUCT PROGRAM
Small Footprint
SIP/DIP Package
Low Ripple and good EMC features
Temperature Range: -40°C to +85°C
No Heat Sink Required
No External Component Required
1KVDC Isolation
Internal SMD construction
Continuous Short Circuit Protection
Industry Standard Pinout
RoHS Compliance
Part
Number
Input
Output
Voltage (VDC)
Voltage Current (mA)
(VDC) Max
Min
Nominal
IB0505LD-W75
5
150
15
68
DIP
IB0509LD-1W
9
111
12
70
DIP
IB0512LD-1W
12
83
9
71
DIP
IB0515LD-1W
15
67
7
73
DIP
5
150
15
68
SIP
IB0509LS-1W
9
111
12
70
SIP
IB0512LS-1W
12
83
9
71
SIP
IB0515LS-1W
15
67
7
73
SIP
IB1205LD-W75
5
150
15
68
DIP
IB1209LD-1W
9
111
12
72
DIP
IB1212LD-1W
12
83
9
70
DIP
IB1215LD-1W
15
67
7
74
DIP
5
150
15
68
SIP
IB0505LS-W75
APPLICATIONS
The IB_LD-1W & IB_LS-1W Series are
Range
Efficiency
Package
(%, Typ)
IB1205LS-W75
5
4.75-5.25
12
11.4-12.6
specially designed for applications where a
IB1209LS-1W
9
111
12
72
SIP
single power supply is highly isolated from the
IB1212LS-1W
12
83
9
70
SIP
input power supply in a distributed power supply
IB1215LS-1W
15
67
7
74
SIP
system on a circuit board.
IB1505LS-W75
5
150
15
70
SIP
These products apply to:
IB1509LS-1W *
9
111
12
71
SIP
1) Where the voltage of the input power supply
IB1512LS-1W *
12
83
9
71
SIP
IB1515LS-1W
15
67
7
72
SIP
IB2405LD-W75*
5
150
15
68
DIP
IB2409LD-1W
9
111
12
68
DIP
IB2412LD-1W
12
83
9
73
DIP
IB2415LD-1W
15
67
7
75
DIP
5
150
15
68
SIP
IB2409LS-1W
9
111
12
68
SIP
IB2412LS-1W
12
83
9
73
SIP
IB2415LS-1W
15
67
7
75
SIP
is fixed (voltage variation ≤±5%);
2) Where isolation is necessary between input
and output (isolation voltage ≤1000VDC);
3) Where the regulation of the output voltage
and
the
output
ripple
and
noise
demanded.
are
IB2405LS-W75
MODEL SELECTION
Rated Power
Package Style
Output Voltage
Input Voltage
Product Series
15
14.25-15.75
24
22.8-25.2
* Designing.
COMMON SPECIFICATION
Item
Test condition
Min
Operating temperature
-40
Storage temperature
-55
Temp. rise at full load
Lead temperature
MORNSUN Science& Technology co.,Ltd.
MORNSUN reserves the copyright
Units
95
%
125
1.5mm from case for 10 seconds
°C
25
300
Continuous
Cooling
Free air convection
Case material
Plastic(UL94-V0)
MTBF
3500
Weight
Specifications subject to change without notice.
Max
85
15
Short circuit protection
Address: 2th floor 6th building, Hangzhou
Industrial District, Guangzhou, China
Tel: 86-20-38601850
Fax: 86-20-38601272
http://www.mornsun-power.com
Typ
Storage humidity
K hours
2.1
IB_LD-1W & IB_LS-1W
A/2-2008
g
Page 1 of 2
ISOLATION SPECIFICATIONS
APPLICATION NOTE
Item
Test condition
Min
Typ
Max
Units
Isolation voltage
Tested for 1 minute
1000
VDC
Isolation resistance
Test at 500VDC
1000
MΩ
Requirement on output load
To ensure this module can operate efficiently
and reliably, During operation, the minimum
output load is not less than 10% of the full load,
OUTPUT SPECIFICATIONS
Item
and that
Test Conditions
Min
Output power
Typ
0.1
this product should never be
Max
Units
operated under no load! If the actual output
1
W
power is very small, please connect a resistor
±0.25
Line regulation
For Vin change of 5%
Load regulation
10% to 100% load
±1
Output voltage accuracy
100% full load
±3
Temperature drift
100% full load
0.03
Ripple*
20MHz Bandwidth
10
20
Noise*
20MHz Bandwidth
50
75
Switching frequency
Full load, nominal input
with proper resistance at the output end in
parallel to increase the load, or use our
%
company’s products with a lower rated output
100
%/°C
power (IB_LD -W25/IB_LS-W25 series).
mVp-p
Recommended circuit
If you want to further
decrease
the
input/output ripple, an “LC” filtering network may
KHz
*Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of
Power Converter section, application notes.
Note:
1. All specifications measured at TA=25°C, humidity<75%, nominal input voltage and rated output load
unless otherwise specified.
2. See below recommended circuits for more details.
be connected to the input and output ends of the
DC/DC converter, see (Figure 1).
L
L
+Vo
Vin
DC DC
Cin
Cout
GND
TYPICAL TEMPERATURE CURVE
0V
(Figure 1)
It should also be noted that the inductance
and the frequency of the “LC” filtering network
should be staggered with the DC/DC frequency
to avoid mutual interference. However, the
capacitance of the output filter capacitor must be
proper. If the capacitance is too big, a startup
problem might arise. For every channel of
output, provided the safe and reliable operation
Operating Temp.( C )
is ensured, the greatest capacitance of its filter
capacitor sees (Table 1).
OUTLINE DIMENSION & PIN CONNECTIONS
EXTERNAL CAPACITOR TABLE (TABLE 1)
Vin
Vout
Cout
Cin
(VDC)
(VDC)
(uF)
(uF)
Fi rst Angle Projection
(0.393)
(0.236)
(0.035)
5.08
(0.200)
(0.079)
1
(0.300)
IBXXXXL D-1W
IBXXXXLS-1W
7
14
11
9
5
12
15
24
4.7
4.7
2.2
1
5
9
12
15
10
4.7
2.2
1
It’s not recommended to connect any external capacitor
4.10
(0.256)
4.10
(0.374)
in the application field with less than 0.5 watt output.
No parallel connection or plug and play.
(0.020)
RECOMMENDED FOOTPRINT
Top view,grid:2.54*2.54mm(0.1*0.1inch),
diameter:1.00mm(0.039inch)
14
1 2
4
6
1
11
9
7
FOOTPRINT DETAILS
Pin
1
2
4
6
SIP
FOOTPRINT DETAILS
Vin
GND
0V
+Vo
Pin
1
Note:
Unit:mm(inch)
Pin section:0.50*0.30mm(0.020*0.012inch)
Pin section tol erances: 0.10mm( 0.004inch)
General tolerances: 0.25mm( 0.010inch)
MORNSUN reserves the copyright
7
9
11
14
DIP
GND
NC
+Vo
0V
Vin
NC:No Connec tion
Specifications subject to change without notice.
IB_LD-1W & IB_LS-1W
A/2-2008
Page 2 of 2
Similar pages