Cypress CY7C138-25JXC 4k x 8/9 dual-port static ram with sem, int, busy Datasheet

CY7C138, CY7C139
4K x 8/9 Dual-Port Static RAM
with Sem, Int, Busy
Features
Functional Description
■
True Dual-Ported Memory Cells that Enable Simultaneous
Reads of the Same Memory Location
■
4K x 8 Organization (CY7C138)
■
4K x 9 Organization (CY7C139)
■
0.65-micron CMOS for Optimum Speed and Power
■
High Speed Access: 15 ns
■
Low Operating Power: ICC = 160 mA (max.)
■
■
Fully Asynchronous Operation
Automatic Power Down
■
TTL Compatible
Expandable Data Bus to 32/36 Bits or more using
Master/Slave Chip Select when using more than one
Device
■ On-Chip Arbitration Logic
■
Semaphores Included to Permit Software Handshaking
between Ports
■ INT Flag for Port-to-Port Communication
■ Available in 68-pin PLCC
■ Pb-free Packages Available
■
The CY7C138 and CY7C139 are high speed CMOS 4K x 8 and
4K x 9 dual-port static RAMs. Various arbitration schemes are
included on the CY7C138/9 to handle situations when multiple
processors access the same piece of data. Two ports are
provided permitting independent, asynchronous access for
reads and writes to any location in memory. The CY7C138/9 can
be used as a standalone 8/9-bit dual-port static RAM or multiple
devices can be combined to function as a 16/18-bit or wider
master/slave dual-port static RAM. An M/S pin is provided for
implementing 16/18-bit or wider memory applications without the
need for separate master and slave devices or additional
discrete logic. Application areas include interprocessor/multiprocessor designs, communications status buffering, and dual-port
video/graphics memory.
Each port has independent control pins: chip enable (CE), read
or write enable (R/W), and output enable (OE). Two flags are
provided on each port (BUSY and INT). BUSY signals that the
port is trying to access the same location currently being
accessed by the other port. The interrupt flag (INT) permits
communication between ports or systems by means of a mail
box. The semaphores are used to pass a flag, or token, from one
port to the other to indicate that a shared resource is in use. The
semaphore logic is comprised of eight shared latches. Only one
side can control the latch (semaphore) at any time. Control of a
semaphore indicates that a shared resource is in use. An
automatic power down feature is controlled independently on
each port by a chip enable (CE) pin or SEM pin.
Logic Block Diagram
R/WL
R/WR
CEL
OEL
CER
OER
(7C139)I/O8L
I/O7L
I/O
CONTROL
I/O0L
I/O8R (7C139)
I/O7R
I/O
CONTROL
I/O0R
[1, 2]
BUSYR
BUSY L[1, 2]
A11L
ADDRESS
DECODER
A0L
CEL
OE L
MEMORY
ARRAY
INTERRUPT
SEMAPHORE
ARBITRATION
A0R
CE R
OER
R/WR
R/WL
SEML
INTL[2]
A11R
ADDRESS
DECODER
M/S
SEMR
INTR[2]
\
Notes
1. BUSY is an output in master mode and an input in slave mode.
2. Interrupt: push-pull output and requires no pull-up resistor.
Cypress Semiconductor Corporation
Document #: 38-06037 Rev. *E
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised June 03, 2009
[+] Feedback
CY7C138, CY7C139
Pin Configurations
9 8 7 6
A6L
A8L
A7L
5 4 3 2 1 68 67 66 65 64 63 62 61
60
59
58
57
56
55
54
53
CY7C138/9
52
51
50
49
48
47
46
45
44
A5L
A4L
A3L
A2L
A1L
A0L
INTL
BUSYL
GND
M/S
BUSYR
INTR
A0R
A1R
A2R
A3R
A4R
A5R
A7R
A6R
A
9R
A8R
2728 29 30 3132 33 34 35 36 37 38 39 40 41 42 43
R/W
R
SEM
R
CER
NC
NC
GND
NC
A
11R
A10R
21
22
23
24
25
26
I/O7R
I/O3R
I/O4R
I/O5R
I/O6R
10
11
12
13
14
15
16
17
18
19
20
NC [3]
OER
I/O2L
I/O3L
I/O4L
I/O5L
GND
I/O6L
I/O7L
VCC
GND
I/O0R
I/O1R
I/O2R
VCC
NC
NC
VCC
NC
A
11L
A
10L
A9L
NC [4]
OE L
R/W L
SEM
L
CEL
I/O 1L
I/O 0L
Figure 1. 68-Pin PLCC (Top View)
Table 1. Pin Definitions
Left Port
I/O0L–7L(8L)
A0L–11L
CEL
OEL
R/WL
SEML
Right Port
I/O0R–7R(8R)
A0R–11R
CER
OER
R/WR
SEMR
INTL
INTR
BUSYL
M/S
VCC
GND
BUSYR
Description
Data Bus Input/Output
Address Lines
Chip Enable
Output Enable
Read/Write Enable
Semaphore Enable. When asserted LOW, allows access to eight semaphores. The
three least significant bits of the address lines will determine which semaphore to
write or read. The I/O0 pin is used when writing to a semaphore. Semaphores are
requested by writing a 0 into the respective location.
Interrupt Flag. INTL is set when right port writes location FFE and is cleared when
left port reads location FFE. INTR is set when left port writes location FFF and is
cleared when right port reads location FFF.
Busy Flag
Master or Slave Select
Power
Ground
Table 2. Selection Guide
Description
Maximum Access Time (ns)
Maximum Operating Current
Maximum Standby Current for ISB1
Commercial
Commercial
7C138-15
7C139-15
15
220
60
7C138-25
7C139-25
25
180
40
7C138-35
7C139-35
35
160
30
7C138-55
7C139-55
55
160
30
Unit
ns
mA
mA
Notes
3. I/O8R on the CY7C139.
4. I/O8L on the CY7C139.
Document #: 38-06037 Rev. *E
Page 2 of 17
[+] Feedback
CY7C138, CY7C139
Maximum Ratings
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.[5]
Static Discharge Voltage........................................... >2001V
(per MIL-STD-883, Method 3015)
Storage Temperature ................................. –65°C to +150°C
Latch Up Current .................................................... >200 mA
Ambient Temperature with
Power Applied ............................................ –55°C to +125°C
Operating Range
Supply Voltage to Ground Potential................–0.5V to +7.0V
Range
DC Voltage Applied to Outputs
in High Z State ................................................–0.5V to +7.0V
Commercial
DC Input
Voltage[6]
.........................................–0.5V to +7.0V
Industrial
Ambient
Temperature
VCC
0°C to +70°C
5V ± 10%
–40°C to +85°C
5V ± 10%
Output Current into Outputs (LOW) ............................. 20 mA
Electrical Characteristics Over the Operating Range
Parameter
Description
Test Conditions
7C138-15
7C139-15
Min
VOH
Output HIGH Voltage
VCC = Min., IOH = –4.0 mA
VOL
Output LOW Voltage
VCC = Min., IOL = 4.0 mA
2.4
Input LOW Voltage
IIX
Input Leakage Current
GND < VI < VCC
IOZ
Output Leakage Current
Output Disabled, GND < VO < VCC
ICC
Operating Current
VCC = Max.,
IOUT = 0 mA,
Outputs Disabled
Commercial
2.2
Standby Current
(Both Ports TTL Levels)
CEL and CER > VIH,
f = fMAX[7]
Commercial
ISB2
Standby Current
(One Port TTL Level)
CEL and CER > VIH,
f = fMAX[7]
Commercial
Standby Current
(Both Ports CMOS Levels)
Both Ports
CE and CER > VCC – 0.2V,
VIN > VCC – 0.2V
or VIN < 0.2V, f = 0[7]
Commercial
Standby Current
(One Port CMOS Level)
One Port
CEL or CER > VCC – 0.2V,
VIN > VCC – 0.2V or
VIN < 0.2V, Active
Port Outputs, f = fMAX[7]
Commercial
V
0.8
V
+10
–10
+10
μA
–10
+10
–10
+10
μA
180
mA
220
190
60
40
130
110
Industrial
mA
50
Industrial
mA
120
15
Industrial
Industrial
V
–10
Industrial
ISB1
V
0.4
0.8
Unit
Max
2.4
2.2
VIL
ISB4
Min
0.4
VIH
ISB3
Max
7C138-25
7C139-25
15
mA
30
125
100
mA
115
Notes
5. The Voltage on any input or I/O pin cannot exceed the power pin during power up.
6. Pulse width < 20 ns.
7. fMAX = 1/tRC = All inputs cycling at f = 1/tRC (except output enable). f = 0 means no address or control lines change. This applies only to inputs at CMOS level standby ISB3
Document #: 38-06037 Rev. *E
Page 3 of 17
[+] Feedback
CY7C138, CY7C139
Electrical Characteristics Over the Operating Range (continued)
Parameter
Description
Test Conditions
7C138-35
7C139-35
Min
VOH
Output HIGH Voltage
VCC = Min., IOH = –4.0 mA
VOL
Output LOW Voltage
VCC = Min., IOL = 4.0 mA
7C138-55
7C139-55
Max
2.4
2.2
Input LOW Voltage
IIX
Input Leakage Current
GND < VI < VCC
–10
+10
IOZ
Output Leakage Current
Output Disabled, GND < VO < VCC
–10
+10
ICC
Operating Current
VCC = Max.,
IOUT = 0 mA,
Outputs Disabled
Commercial
Standby Current
(Both Ports TTL Levels)
ISB3
ISB4
V
0.4
2.2
VIL
ISB2
Unit
Max
2.4
0.4
VIH
ISB1
Min
0.8
V
V
0.8
V
–10
+10
μA
–10
+10
μA
160
160
mA
Industrial
180
180
CEL and CER > VIH,
f = fMAX[7]
Commercial
30
30
Industrial
40
40
Standby Current
(One Port TTL Level)
CEL and CER > VIH,
f = fMAX[7]
Commercial
100
100
Industrial
110
110
Standby Current
(Both Ports CMOS Levels)
Both Ports
CE and CER > VCC – 0.2V,
VIN > VCC – 0.2V
or VIN < 0.2V, f = 0[7]
Commercial
15
15
Industrial
30
30
Standby Current
(One Port CMOS Level)
One Port
CEL or CER > VCC – 0.2V,
VIN > VCC – 0.2V or
VIN < 0.2V, Active
Port Outputs, f = fMAX[7]
Commercial
90
90
Industrial
100
100
mA
mA
mA
mA
Capacitance[8]
Parameter
Description
CIN
Input Capacitance
COUT
Output Capacitance
Document #: 38-06037 Rev. *E
Test Conditions
TA = 25°C, f = 1 MHz,
VCC = 5.0V
Max
Unit
10
pF
15
pF
Page 4 of 17
[+] Feedback
CY7C138, CY7C139
Figure 2. AC Test Loads and Waveforms
5V
5V
R1 = 893Ω
OUTPUT
OUTPUT
C = 30 pF
R1 = 893Ω
RTH = 250Ω
OUTPUT
C = 30pF
R2 = 347Ω
C = 5 pF
R2 = 347Ω
VTH = 1.4V
(b) Thévenin Equivalent(Load 1)
(a) Normal Load (Load 1)
(c) Three-State Delay (Load 3)
ALL INPUT PULSES
OUTPUT
3.0V
C = 30 pF
GND
90%
10%
90%
10%
< 3 ns
< 3 ns
Load (Load 2)
Switching Characteristics Over the Operating Range[9]
Parameter
Description
7C138-15
7C139-15
Min
Max
7C138-25
7C139-25
Min
Max
7C138-35
7C139-35
Min
Max
7C138-55
7C139-55
Min
Unit
Max
READ CYCLE
tRC
Read Cycle Time
15
tAA
Address to Data Valid
tOHA
Output Hold From Address Change
tACE
CE LOW to Data Valid
15
25
35
55
ns
tDOE
OE LOW to Data Valid
10
15
20
25
ns
tLZOE[10,11,12]
tHZOE[10,11,12]
tLZCE[10,11,12]
tHZCE[10,11,12]
tPU[12]
tPD[12]
OE Low to Low Z
15
3
CE LOW to Power Up
25
10
0
CE HIGH to Power Down
35
15
0
15
55
20
0
25
ns
25
3
20
ns
ns
25
0
35
ns
ns
3
3
15
ns
3
3
3
10
55
3
3
3
CE HIGH to High Z
35
3
3
OE HIGH to High Z
CE LOW to Low Z
25
ns
ns
55
ns
WRITE CYCLE
tWC
Write Cycle Time
15
25
35
55
ns
tSCE
CE LOW to Write End
12
20
30
40
ns
tAW
Address Setup to Write End
12
20
30
40
ns
tHA
Address Hold From Write End
2
2
2
2
ns
tSA
Address Setup to Write Start
0
0
0
0
ns
tPWE
Write Pulse Width
12
20
25
30
ns
tSD
Data Setup to Write End
10
15
15
20
ns
tHD
Data Hold From Write End
0
0
0
0
ns
Note
8. Tested initially and after any design or process changes that may affect these parameters.
Document #: 38-06037 Rev. *E
Page 5 of 17
[+] Feedback
CY7C138, CY7C139
Switching Characteristics Over the Operating Range[9] (continued)
Parameter
7C138-15
7C139-15
Description
Min
tHZWE[11,12]
R/W LOW to High Z
tLZWE[11,12]
tWDD[13]
tDDD[13]
R/W HIGH to Low Z
Max
7C138-25
7C139-25
Min
10
3
Max
7C138-35
7C139-35
Min
Max
15
3
7C138-55
7C139-55
Min
20
3
Unit
Max
25
3
ns
ns
Write Pulse to Data Delay
30
50
60
70
ns
Write Data Valid to Read Data Valid
25
30
35
40
ns
[14]
BUSY TIMING
tBLA
BUSY LOW from Address Match
15
20
20
45
ns
tBHA
BUSY HIGH from Address Mismatch
15
20
20
40
ns
tBLC
BUSY LOW from CE LOW
15
20
20
40
ns
tBHC
BUSY HIGH from CE HIGH
15
20
20
35
ns
tPS
Port Setup for Priority
tWB
R/W LOW after BUSY LOW
0
0
tWH
R/W HIGH after BUSY HIGH
13
20
tBDD[15]
BUSY HIGH to Data Valid
INTERRUPT
5
5
5
5
ns
0
0
ns
30
40
ns
Note 15
Note 15
Note 15
Note 15
ns
TIMING[14]
tINS
INT Set Time
15
25
25
30
ns
tINR
INT Reset Time
15
25
25
30
ns
SEMAPHORE TIMING
tSOP
SEM Flag Update Pulse (OE or SEM)
10
10
15
20
ns
tSWRD
SEM Flag Write to Read Time
5
5
5
5
ns
tSPS
SEM Flag Contention Window
5
5
5
5
ns
Switching Waveforms
Figure 3. Read Cycle No. 1 (Either Port Address Access)[16, 17]
tRC
ADDRESS
tOHA
DATA OUT
PREVIOUS DATA VALID
tAA
DATA VALID
Notes
9. Test conditions assume signal transition time of 3 ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V, and output loading of the specified IOI/IOH
and 30-pF load capacitance.
10. At any temperature and voltage condition for any device, tHZCE is less than tLZCE and tHZOE is less than tLZOE.
11. Test conditions used are Load 3.
12. This parameter is guaranteed but not tested.
13. For information on part-to-part delay through RAM cells from writing port to reading port, refer to Read Timing with Port-to-Port Delay waveform.
14. Test conditions used are Load 2.
15. tBDD is a calculated parameter and is the greater of tWDD – tPWE (actual) or tDDD – tSD (actual).
Document #: 38-06037 Rev. *E
Page 6 of 17
[+] Feedback
CY7C138, CY7C139
Switching Waveforms
(continued)
Figure 4. Read Cycle No. 2 (Either Port CE/OE Access)[16, 18, 19]
SEM or CE
tHZCE
tACE
OE
tLZOE
tHZOE
tDOE
tLZCE
DATA VALID
DATA OUT
tPU
tPD
ICC
ISB
Figure 5. Read Timing with Port-to-Port Delay (M/S = L)[20, 21]
tWC
ADDRESS R
MATCH
t
R/W R
PWE
t
DATA INR
ADDRESS L
t
SD
HD
VALID
MATCH
tDDD
DATAOUTL
VALID
tWDD
Notes
16. R/W is HIGH for read cycle.
17. Device is continuously selected CE = LOW and OE = LOW. This waveform cannot be used for semaphore reads.
18. Address valid prior to or coincident with CE transition LOW.
19. CEL = L, SEM = H when accessing RAM. CE = H, SEM = L when accessing semaphores.
Document #: 38-06037 Rev. *E
Page 7 of 17
[+] Feedback
CY7C138, CY7C139
Switching Waveforms
(continued)
Figure 6. Write Cycle No. 1: OE Three-States Data I/Os (Either Port)[22, 23, 24]
tWC
ADDRESS
tSCE
SEM OR CE
tAW
tHA
tPWE
R/W
tSA
tSD
DATA IN
tHD
DATA VALID
OE
t
tHZOE
LZOE
HIGH IMPEDANCE
DATA OUT
Figure 7. Write Cycle No. 2: R/W Three-States Data I/Os (Either Port)[22, 24, 25]
tWC
ADDRESS
tSCE
tHA
SEM OR CE
R/W
tSA
tAW
tPWE
tSD
DATA VALID
DATA IN
tHZWE
DATA OUT
tHD
tLZWE
HIGH IMPEDANCE
Notes
20. BUSY = HIGH for the writing port.
21. CEL = CER = LOW.
22. The internal write time of the memory is defined by the overlap of CE or SEM LOW and R/W LOW. Both signals must be LOW to initiate a write, and either signal can
terminate a write by going HIGH. The data input setup and hold timing should be referenced to the rising edge of the signal that terminates the write.
23. If OE is LOW during a R/W controlled write cycle, the write pulse width must be the larger of tPWE or (tHZWE + tSD) to allow the I/O drivers to turn off and data to be
placed on the bus for the required tSD. If OE is HIGH during a R/W controlled write cycle (as in this example), this requirement does not apply and the write pulse can
be as short as the specified tPWE.
24. R/W must be HIGH during all address transitions.
Document #: 38-06037 Rev. *E
Page 8 of 17
[+] Feedback
CY7C138, CY7C139
Switching Waveforms
(continued)
Figure 8. Semaphore Read After Write Timing, Either Side[26]
tAA
A0–A 2
VALID ADDRESS
VALID ADDRESS
tAW
tACE
tHA
SEM
tOHA
tSCE
tSOP
tSD
I/O0
DATAIN VALID
tSA
DATAOUT VALID
tHD
tPWE
R/W
tSWRD
tDOE
tSOP
OE
WRITE CYCLE
READ CYCLE
Figure 9. Timing Diagram of Semaphore Contention[27, 28, 29]
A0L–A2L
MATCH
R/WL
SEML
tSPS
A0R–A2R
MATCH
R/WR
SEMR
Notes
25. Data I/O pins enter high impedance when OE is held LOW during write.
26. CE = HIGH for the duration of the above timing (both write and read cycle).
Document #: 38-06037 Rev. *E
Page 9 of 17
[+] Feedback
CY7C138, CY7C139
Switching Waveforms
(continued)
Figure 10. Timing Diagram of Read with BUSY (M/S = HIGH)[21]
tWC
ADDRESS R
MATCH
tPWE
R/WR
tSD
DATA INR
tHD
VALID
tPS
ADDRESS L
MATCH
tBLA
tBHA
BUSYL
tBDD
tDDD
DATAOUTL
VALID
tWDD
Figure 11. Write Timing with Busy Input (M/S=LOW)
tPWE
R/W
BUSY
tWB
tWH
Notes
27. I/O0R = I/O0L = LOW (request semaphore); CER = CEL = HIGH
28. Semaphores are reset (available to both ports) at cycle start.
29. If tSPS is violated, the semaphore will definitely be obtained by one side or the other, but there is no guarantee which side will control the semaphore.
Document #: 38-06037 Rev. *E
Page 10 of 17
[+] Feedback
CY7C138, CY7C139
Switching Waveforms
(continued)
Figure 12. Busy Timing Diagram No. 1 (CE Arbitration)[30]
CEL Valid First:
ADDRESS L,R
ADDRESS MATCH
CEL
tPS
CER
tBLC
tBHC
BUSYR
CER Valid First:
ADDRESS L,R
ADDRESS MATCH
CER
tPS
CEL
tBLC
tBHC
BUSY L
Figure 13. Busy Timing Diagram No. 2 (Address Arbitration)[30]
Left Address Valid First:
tRC or tWC
ADDRESS L
ADDRESS MATCH
ADDRESS MISMATCH
tPS
ADDRESS R
tBLA
tBHA
BUSYR
Right Address Valid First:
tRC or tWC
ADDRESS R
ADDRESS MATCH
ADDRESS MISMATCH
tPS
ADDRESS L
tBLA
tBHA
BUSY L
Note
30. If tPS is violated, the busy signal will be asserted on one side or the other, but there is no guarantee on which side BUSY will be asserted.
Document #: 38-06037 Rev. *E
Page 11 of 17
[+] Feedback
CY7C138, CY7C139
Switching Waveforms
(continued)
Figure 14. Interrupt Timing Diagrams
Left Side Sets INTR:
tWC
ADDRESS L
WRITE FFF
tHA[31]
CE L
R/W L
INTR
tINS[32]
Right Side Clears INTR:
tRC
ADDRESSR
READ FFF
CE R
tINR[32]
R/W R
OE R
INT R
Right Side Sets INTL:
tWC
ADDRESSR
WRITE FFE
tHA[31]
CER
R/W R
INT L
tINS[32]
Left Side Clears INTL:
tRC
ADDRESSR
READ FFE
CE L
tINR [32]
R/W L
OE L
INT L
Notes
31. tHA depends on which enable pin (CEL or R/WL) is deasserted first.
32. tINS or tINR depends on which enable pin (CEL or R/WL) is asserted last.
Document #: 38-06037 Rev. *E
Page 12 of 17
[+] Feedback
CY7C138, CY7C139
Architecture
The CY7C138/9 consists of an array of 4K words of 8/9 bits each
of dual-port RAM cells, I/O and address lines, and control signals
(CE, OE, R/W). These control pins permit independent access
for reads or writes to any location in memory. To handle simultaneous writes and reads to the same location, a BUSY pin is
provided on each port. Two interrupt (INT) pins can be used for
port–to–port communication. Two semaphore (SEM) control
pins are used for allocating shared resources. With the M/S pin,
the CY7C138/9 can function as a master (BUSY pins are
outputs) or as a slave (BUSY pins are inputs). The CY7C138/9
has an automatic power down feature controlled by CE. Each
port is provided with its own output enable control (OE), which
enables data to be read from the device.
Functional Description
Write Operation
Data must be set up for a duration of tSD before the rising edge
of R/W in order to guarantee a valid write. A write operation is
controlled by either the OE pin (see Write Cycle No. 1 waveform)
or the R/W pin (see Write Cycle No. 2 waveform). Data can be
written to the device tHZOE after the OE is deasserted or tHZWE
after the falling edge of R/W. Required inputs for non-contention
operations are summarized in Table 3.
If a location is being written to by one port and the opposite port
attempts to read that location, a port-to-port flowthrough delay
must be met before the data is read on the output; otherwise the
data read is not deterministic. Data is valid on the port tDDD after
the data is presented on the other port.
Read Operation
When reading the device, the user must assert both the OE and
CE pins. Data is available tACE after CE or tDOE after OE is
asserted. If the user of the CY7C138/9 wishes to access a
semaphore flag, then the SEM pin must be asserted instead of
the CE pin.
Interrupts
The interrupt flag (INT) permits communications between
ports.When the left port writes to location FFF, the right port’s
interrupt flag (INTR) is set. This flag is cleared when the right port
reads that same location. Setting the left port’s interrupt flag
(INTL) is accomplished when the right port writes to location FFE.
This flag is cleared when the left port reads location FFE. The
message at FFF or FFE is user-defined. See Table 4 for input
requirements for INT. INTR and INTL are push-pull outputs and
do not require pull-up resistors to operate. BUSYL and BUSYR
in master mode are push-pull outputs and do not require pull-up
resistors to operate.
Busy
The CY7C138/9 provides on-chip arbitration to alleviate simultaneous memory location access (contention). If both ports’ CEs
are asserted and an address match occurs within tPS of each
other the Busy logic determines which port has access. If tPS is
violated, one port definitely gains permission to the location, but
it is not guaranteed which one. BUSY will be asserted tBLA after
an address match or tBLC after CE is taken LOW.
Document #: 38-06037 Rev. *E
Master/Slave
A M/S pin is provided to expand the word width by configuring
the device as either a master or a slave. The BUSY output of the
master is connected to the BUSY input of the slave. This enables
the device to interface to a master device with no external
components.Writing of slave devices must be delayed until after
the BUSY input has settled. Otherwise, the slave chip may begin
a write cycle during a contention situation.When presented as a
HIGH input, the M/S pin allows the device to be used as a master
and therefore the BUSY line is an output. BUSY can then be
used to send the arbitration outcome to a slave.
Semaphore Operation
The CY7C138/9 provides eight semaphore latches, which are
separate from the dual-port memory locations. Semaphores are
used to reserve resources that are shared between the two
ports.The state of the semaphore indicates that a resource is in
use. For example, if the left port wants to request a resource, it
sets a latch by writing a zero to a semaphore location. The left
port then verifies its success in setting the latch by reading it.
After writing to the semaphore, SEM or OE must be deasserted
for tSOP before attempting to read the semaphore. The
semaphore value is available tSWRD + tDOE after the rising edge
of the semaphore write. If the left port was successful (reads a
zero), it assumes control over the shared resource, otherwise
(reads a one) it assumes the right port has control and continues
to poll the semaphore.When the right side has relinquished
control of the semaphore (by writing a one), the left side
succeeds in gaining control of the a semaphore.If the left side no
longer requires the semaphore, a 1 is written to cancel its
request.
Semaphores are accessed by asserting SEM LOW. The SEM
pin functions as a chip enable for the semaphore latches (CE
must remain HIGH during SEM LOW). A0–2 represents the
semaphore address. OE and R/W are used in the same manner
as a normal memory access. When writing or reading a
semaphore, the other address pins have no effect.
When writing to the semaphore, only I/O0 is used. If a zero is
written to the left port of an unused semaphore, a one will appear
at the same semaphore address on the right port. That
semaphore can now only be modified by the side showing zero
(the left port in this case). If the left port now relinquishes control
by writing a one to the semaphore, the semaphore is set to 1 for
both sides. However, if the right port had requested the
semaphore (written a zero) while the left port had control, the
right port immediately owns the semaphore after the left port
releases it. Table 5 shows sample semaphore operations.
When reading a semaphore, all eight or nine data lines output
the semaphore value. The read value is latched in an output
register to prevent the semaphore from changing state during a
write from the other port. If both ports attempt to access the
semaphore within tSPS of each other, the semaphore is definitely
obtained by one side or the other, but there is no guarantee which
side controls the semaphore.
Initialization of the semaphore is not automatic and must be reset
during initialization program at power up. All semaphores on both
sides should have a 1 written into them at initialization from both
sides to assure that they are free when needed.
Page 13 of 17
[+] Feedback
CY7C138, CY7C139
Table 3. Non-Contending Read/Write
Inputs
CE
Outputs
Operation
R/W
OE
SEM
H
X
X
H
High Z
Power Down
H
H
L
L
Data Out
Read Data in Semaphore
X
X
H
X
High Z
I/O Lines Disabled
X
L
Data In
Write to Semaphore
H
L
H
Data Out
Read
L
L
X
H
Data In
Write
L
X
X
L
H
L
I/O0-7/8
Illegal Condition
Table 4. Interrupt Operation Example (assumes BUSYL=BUSYR=HIGH)
Left Port
Function
Right Port
R/W
CE
OE
A0-11
INT
R/W
CE
OE
A0-11
INT
Set Left INT
X
X
X
X
L
L
L
X
FFE
X
Reset Left INT
X
L
L
FFE
H
X
X
X
X
X
Set Right INT
L
L
X
FFF
X
X
X
X
X
L
Reset Right INT
X
X
X
X
X
X
L
L
FFF
H
Table 5. Semaphore Operation Example
I/O0-7/8 Left
I/O0-7/8 Right
No action
Function
1
1
Semaphore free
Left port writes semaphore
0
1
Left port obtains semaphore
Right port writes 0 to semaphore
0
1
Right side is denied access
Left port writes 1 to semaphore
1
0
Right port is granted access to semaphore
Left port writes 0 to semaphore
1
0
No change. Left port is denied access
Right port writes 1 to semaphore
0
1
Left port obtains semaphore
Left port writes 1 to semaphore
1
1
No port accessing semaphore address
Right port writes 0 to semaphore
1
0
Right port obtains semaphore
Right port writes 1 to semaphore
1
1
No port accessing semaphore
Left port writes 0 to semaphore
0
1
Left port obtains semaphore
Left port writes 1 to semaphore
1
1
No port accessing semaphore
Document #: 38-06037 Rev. *E
Status
Page 14 of 17
[+] Feedback
CY7C138, CY7C139
ICC
1.0
ISB3
0.8
0.6
0.4
0.2
0.0
4.0
4.5
5.0
5.5
ICC
1.0
ISB3
0.8
0.6
VCC = 5.0V
VIN = 5.0V
0.4
0.2
0.6
–55
6.0
NORMALIZED ACCESS TIME
vs. AMBIENT TEMPERATURE
NORMALIZED ACCESS TIME
vs. SUPPLY VOLTAGE
1.4
1.6
1.3
1.4
NORMALIZED tAA
NORMALIZED tAA
125
1.2
1.1
TA = 25°C
1.2
1.0
VCC = 5.0V
0.8
0.9
0.8
4.0
4.5
5.0
5.5
OUTPUT SOURCE CURRENT
vs. OUTPUT VOLTAGE
200
160
120
VCC = 5.0V
TA = 25°C
80
40
0
0
AMBIENT TEMPERATURE (°C)
SUPPLY VOLTAGE (V)
1.0
25
0.6
–55
6.0
25
2.0
3.0
4.0
5.0
140
OUTPUT SINK CURRENT
vs. OUTPUT VOLTAGE
120
100
80
60
40
VCC = 5.0V
TA = 25°C
20
0
0.0
125
1.0
2.0
3.0
4.0
5.0
OUTPUT VOLTAGE (V)
AMBIENT TEMPERATURE (°C)
SUPPLY VOLTAGE (V)
1.0
OUTPUT VOLTAGE (V)
OUTPUT SINK CURRENT (mA)
1.2
1.2
NORMALIZED I,CC ISB
NORMALIZED ICC, ISB
1.4
NORMALIZED SUPPLY CURRENT
vs. AMBIENT TEMPERATURE
NORMALIZED SUPPLY CURRENT
vs. SUPPLY VOLTAGE
OUTPUT SOURCE CURRENT (mA)
Figure 15. Typical DC and AC Characteristics
VIN = 5.0V
TYPICAL POWER-ON CURRENT
vs. SUPPLY VOLTAGE
TYPICAL ACCESS TIME CHANGE
vs. OUTPUT LOADING
30.0
1.00
NORMALIZED ICC
DELTA tAA (ns)
NORMALIZED tPC
25.0
0.75
20.0
15.0
0.50
0.0
1.0
2.0
3.0
4.0
SUPPLY VOLTAGE (V)
Document #: 38-06037 Rev. *E
5.0
0
VCC = 5.0V
TA = 25°C
VIN = 5.0V
1.0
VCC = 4.5V
TA = 25°C
5.0
0
NORMALIZED ICC vs. CYCLE TIME
0.75
10.0
0.25
1.25
0
200
400
600
800 1000
CAPACITANCE (pF)
0.50
10
28
40
66
CYCLE FREQUENCY (MHz)
Page 15 of 17
[+] Feedback
CY7C138, CY7C139
Ordering Information
4K x8 Dual-Port SRAM
Speed
(ns)
15
25
35
55
Ordering Code
Package
Diagram
Package Type
Operating
Range
CY7C138-15JC
51-85005
68-Pin Plastic Leaded Chip Carrier
CY7C138-15JXC
51-85005
68-Pin Plastic Leaded Chip Carrier (Pb-free)
Commercial
CY7C138-25JC
51-85005
68-Pin Plastic Leaded Chip Carrier
CY7C138-25JXC
51-85005
68-Pin Plastic Leaded Chip Carrier (Pb-free)
CY7C138-25JI
51-85005
68-Pin Plastic Leaded Chip Carrier
CY7C138-25JXI
51-85005
68-Pin Plastic Leaded Chip Carrier (Pb-free)
CY7C138-35JC
51-85005
68-Pin Plastic Leaded Chip Carrier
Commercial
CY7C138-35JI
51-85005
68-Pin Plastic Leaded Chip Carrier
Industrial
CY7C138-55JC
51-85005
68-Pin Plastic Leaded Chip Carrier
Commercial
CY7C138-55JI
51-85005
68-Pin Plastic Leaded Chip Carrier
Industrial
Commercial
Industrial
Package Diagram
Figure 16. 68-Pin Plastic Leaded Chip Carrier (51-85005)
51-85005-*A
Document #: 38-06037 Rev. *E
Page 16 of 17
[+] Feedback
CY7C138, CY7C139
Document History Page
Document Title: CY7C138, CY7C139 4K x 8/9 Dual-Port Static RAM with Sem, Int, Busy
Document Number: 38-06037
Rev.
ECN No.
Orig. of
Change
**
110180
SZV
Submission Description of Change
Date
09/29/01
Change from Spec number: 38-00536 to 38-06037
*A
122287
RBI
12/27/02
Power up requirements added to Maximum Ratings Information
*B
393403
YIM
See ECN
Added Pb-Free Logo
Added Pb-Free parts to ordering information:
CY7C138-15JXC, CY7C138-25JXC, CY7C139-25JXC
*C
2623658
VKN/PYRS
12/17/08
Added CY7C138-25JXI part
Removed CY7C139 from the Ordering information table
*D
2672737
GNKK
*E
2714768
VKN/AESA
03/12/2009 Corrected title in the Document History table
06/04/2009 Corrected defective Logic Block diagram, Pinouts and Package diagrams
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at cypress.com/sales.
Products
PSoC
Clocks & Buffers
psoc.cypress.com
clocks.cypress.com
Wireless
wireless.cypress.com
Memories
memory.cypress.com
Image Sensors
image.cypress.com
© Cypress Semiconductor Corporation, 2005-2009. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document #: 38-06037 Rev. *E
Revised June 03, 2009
Page 17 of 17
All products and company names mentioned in this document may be the trademarks of their respective holders.
[+] Feedback
Similar pages