Vectron EX-4202-DAT-107 Evacuated miniature crystal oscillator Datasheet

EX-420
Evacuated Miniature Crystal Oscillator
EX-420
Description
The EX-420 provides exceptionally low aging rates and tight temperature stabilities in an extremely small package over a wide
range of environmental conditions. This EMXO series bridges the gap between current large, high precision OCXO’s and smaller
TCXO’s. The EX-420 Series becomes the most economical choice where there is a need for spectral purity, short and long term
stability, along with small size and dramatically reduced power consumption.
Features
•
•
•
•
•
Applications
4-Pin Half Dip
Fast Warmup
Low Power Consumption
Previous Model Number: EX-620 series
Frequency Range: 10 MHz - 30 MHz
•
•
•
•
SONET/SDH, DWDM, FDM, ATM, 3G
Telecom Transmission and Switching Equipment
Wireless Communication Equipment
Military Airborne and Mobile systems
Performance Specifications
Frequency Stabilities1
Parameter
vs. operating temperature range (referenced to +25°C)
Min
-50
-75
-100
Typ
Max
Units
Condition
+50
+75
+100
ppb
ppb
ppb
0… +70°C
-20… +70°C
-40… +85°C
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Performance Specifications
Frequency Stabilities1
Parameter
vs. Stratum
3 per
GR-1244CORE
Operating Temp
Holdover
Drift
MTIE
Min
Typ
-140
-140
-370
-4.63
Warm-up Time
Initial Accuracy
vs. supply voltage change
vs. load change
vs. aging / day
vs. aging / 1 year
-1
-20
-10
-2.0
-300
Max
Units
Condition
+140
+140
+370
+4.63
+1
ppb
ppb
ppb
ppb
10-13/sec
ppm
-20… +70°C
-40… +85°C
24 hours
Over 7100 seconds
0.16 sec < Observe Times < 64 sec
1
1.5
minutes
minutes
to ± 100 ppb of final frequency (1 hour) @+25°C
to ± 100ppb of final frequency (1 hour) @-40°C
+1
+20
+10
+2.0
+300
ppm
ppb
ppb
ppb
ppb
fixed frequency, no EFC input
VS ± 5%
Load ± 5%
after 30 days of operation
after 30 days of operation
Supply Voltage (Vs)
Supply voltage (Standard)
4.75
5.0
5.25
VDC
Supply voltage (Option)
3.135
3.3
3.465
VDC
1.5
0.3
0.6
Watts
Watts
Watts
Power Consumption
during warm-up
steady state @ +25°C
steady state @ -40°C
RF Output
Signal [Standard]
HCMOS
15
Load
Signal Level (Vol)
pF
0.1
Signal Level (Voh)
0.8
Duty cycle
40
VDC
VDC
60
%
(Voh-Vol)/2
Sinewave
Signal [Standard]
50
Load
Output Power [Standard]
Output Power [Option]
0
+3
ohm
+4
+7
dBm
dBm
50 Ohm load
50 Ohm load
Harmonics
-30
dBc
50 Ohm load
Spurs
-60
dBc
50 Ohm load
Frequency Tuning (EFC) 10 to 80 MHz
Tuning Range
Fixed EMXO; No adjust
Tuning Range
±3.0
Linearity
±10.0
ppm
20
%
from 0V to Vs
Positive
Tuning Slope
Additional Parameters
Phase Noise
Allan Deviation
Weight
Processing & Packing
-100
-130
-140
-145
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
10 Hz
100 Hz
1 KHz
10 KHz
0.2
ppb
Tau = 1 sec to 10 sec
3
g
Handling & processing note
Absolute Maximum Ratings
Supply Voltage
5.5
VDC
Output Load
30
pF
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Frequency Stabilities1
Parameter
Min
Typ
Max
Units
Operable temperature range
-55
+85
°C
Storage temperature range
-55
+85
°C
Condition
Environmental Conditions
• Mechanical Shock (survive)
MIL-STD-202, Test Method 213, Condition E (100G, 0.5msec)
• Vibration Random (survive)
MIL-STD-202, Test Method 214, Condition I-H (20Grms, 3 minutes/axis)
• Vibration Sine (survive)
MIL-STD-202, Test Method 204, Condition D (20Grms, 20 minutes/axis)
• Thermal Shock (survive)
MIL-STD-202, Test Method 107, Condition A-2 (50 Cycles, -55°C to +85 °C)
Outline Drawing / Enclosure
Dimensions in mm (inches)
Type A
Code
Height “H”
Pin Length “L”
0
7.62
5.08
Code
Height “H”
Pin Length “L”
1
8.89
NA
2
9.65
NA
Type B
Pin Connections
1
EFC \ No Connect
2
Ground (Case)
3
RF Output
4
Supply Voltage Input
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Recommended Reflow Profile
tp
Critical Zone
Tp
TL to Tp
Ramp up
TL
tL
Temperature
Ts
Ramp dow n
Ts
ts
preheat
25
t 25°C to peak
Time
Profile Feature
PRECAUTION:
Sn-Pb Assembly
Profile Feature
Sn-Pb Assembly
Series shall not expose to temperature higher than 230°C. If exposing to temperature higher than
230°C, stability and power consumption may permanently degrade.
Average ramp-up rate (TL to Tp)
3°C/second max.
Time 25°C to Peak Temperature
4 minutes max.
Preheat -Temperature Min Tsmin)
-Temperature Min Tsmax)
-Time (min to max) (ts)
135°c
155°c
60-90 seconds
Time maintained above
- Temperature (TL)
- Time (tL)
183°C
45-60 seconds
Tsmax to TL - Ramp-up Rate
3°C/second max.
Time maintained above
- Temperature (TL) 183°C
- Time (tL)
45-60 seconds
Time within 5°C of actual
Peak Temperature (tp)
10-20 seconds max.
Peak Temperature (Tp)
Ramp-down Rate
6°C/second max.
max 220°C
Note: All temperatures refer to topside of the package, measured on the package body surface.
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Ordering Information
EX - 420 0 - D A J - 107 0 - 10M0000000
Frequency
Product Family
EX: EMXO
Package
13x 13mm
Height
0: A 7.62mm (HCMOS only)
1: B 8.89mm (HCMOS only)
2: B 9.65mm (Sinewave only)
Stability Code
508: ±50ppb
758: ±75ppb
107: ±100ppb
147: ±140ppb(ST3)
Supply Voltage
D: 5 Vdc
E: 3.3 Vdc
Frequency Control
0: Fixed Frequency (HCMOS)
1: Fixed Frequency (0 dBm)
2: Fixed Frequency (+3 dBm)
3: Electrical Tuning (HCMOS)
4: Electrical Tuning (0 dBm)
5: Electrical Tuning (+3 dBm)
Temperature Range
E: -40°C to +85°C
J: -20°C to +70°C
T: 0°C to +70°C
RF Output Code
A: HCMOS
E: Sinewave
Notes:
1. Contact factory for improved stabilities or additional product options. Not all options and codes are available at all
frequencies.
2. Unless other stated all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency
control voltage, load, temperature (25°C).
3. Phase noise degrades with increasing output frequency.
4. Subject to technical modification.
5. Contact factory for availability.
For Additional Information, Please Contact
USA:
Europe:
Asia:
Vectron International
267 Lowell Road
Hudson, NH 03051
Tel: 1.888.328.7661
Fax: 1.888.329.8328
Vectron International
Landstrasse, D-74924
Neckarbischofsheim, Germany
Tel: +49 (0) 3328.4784.17
Fax: +49 (0) 3328.4784.30
Vectron International
1F-2F, No 8 Workshop, No 308 Fenju Road
WaiGaoQiao Free Trade Zone
Pudong, Shanghai, China 200131
Tel: 86.21.5048.0777
Fax: 86.21.5048.1881
Disclaimer
Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application.
No rights under any patent accompany the sale of any such product(s) or information.
Rev: 11-25-2008 daf
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Similar pages