Coilcraft LPO6013-683KL Smt power inductor Datasheet

Document 286-1
SMT Power Inductors - LPO6013 Series
• Very low profile – only 1.3 mm high!
• Handles saturating current up to 1.9 Amps
Designer’s Kit C352 contains 3 each of all values
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Terminations RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Weight 111 – 122 mg
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 1000/7″reel; 3500/13″ reel Plastic tape: 12 mm wide,
0.23 mm thick, 8 mm pocket spacing, 1.4 mm pocket depth
Recommended pick and place nozzle OD: 5.6 mm; ID: ≤ 2.8 mm
PCB washing Only pure water or alcohol recommended
1
2
2
Part number
1
LPO6013-102ML_
LPO6013-152ML_
LPO6013-222ML_
LPO6013-332ML_
LPO6013-392ML_
L2
(µH)
1.0
1.5
2.2
3.3
3.9
DCR
SRF
max
typ 2Isat3 3Irms4
(Ohms) (MHz) (A)
(A)
±20%
±20%
±20%
±20%
±20%
0.06
0.07
0.08
0.11
0.13
200
200
150
110
100
1.9
1.6
1.3
1.1
1.0
1.5
1.4
1.3
1.3
1.2
LPO6013-472ML_
LPO6013-682ML_
LPO6013-822ML_
LPO6013-103KL_
LPO6013-153KL_
4.7 ±20%
6.8 ±20%
8.2 ±20%
10. ±10%
15. ±10%
0.15
0.20
0.22
0.30
0.38
90
70
65
60
47
0.90
0.70
0.70
0.60
0.55
1.2
1.2
1.0
1.0
0.85
LPO6013-223KL_
LPO6013-333KL_
LPO6013-393KL_
LPO6013-473KL_
LPO6013-683KL_
22. ±10%
33. ±10%
39. ±10%
47. ±10%
68. ±10%
0.52
0.73
0.96
1.0
1.7
37
30
28
25
21
0.45
0.40
0.35
0.30
0.28
0.80
0.74
0.67
0.60
0.49
LPO6013-104KL_
LPO6013-154KL_
LPO6013-224KL_
LPO6013-334KL_
LPO6013-474KL_
100. ±10%
150. ±10%
220. ±10%
330. ±10%
470. ±10%
17
14
10
8
7
0.22
0.19
0.15
0.13
0.10
0.35
0.30
0.26
0.23
0.20
5.6 0.09
4.7 0.07
0.18
0.13
LPO6013-684KL_ 680. ±10%
LPO6013-105KL_ 1000. ±10%
3.2
4.3
5.8
7
10
14
21
1. When ordering, please specify termination and packaging code:
LPO6013-473KLC
Termination: L = RoHS compliant silver-palladium-platinum-glass frit.
Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or
S = non-RoHS tin-lead (63/37).
Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic
tape (1000 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
D = 13″ machine-ready reel. EIA-481 embossed plastic
tape (3500 parts per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc.
3. DC current at which the inductance drops 10% (typ) from its value
without current.
4. Current that causes a 40°C temperature rise from 25°C ambient.
5. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Specifications subject to change without notice.
Please check our website for latest information.
© Coilcraft, Inc. 2009
Document 286-1
Revised 10/15/08
Document 286-2
SMT Power Inductors - LPO6013 Series
Typical L vs Frequency
Typical L vs Current
10000
10000
1000 µH
100 µH
100
10 µH
10
1 µH
1
100 µH
100
10 µH
10
1 µH
1
0.1
0.01
1000 µH
1000
Inductance (µH)
Inductance (µH)
1000
1
0.1
10
0.1
0.01
10
Current (A)
Irms Derating
0.051 max
1,3
120
0.220 max
5,6
110
Dash number
0.040 ±0.005
1,016 ±0,127
100
90
XXX
0.236 max
6,0
80
X
70
60
50
Internal code
0.134
3,4
40
25°C
Percent of rated Irms
1
0.1
Frequency (MHz)
30
20
10
0.200
5,08
0
-40
-20
0
20
40
60
80
100
120 140
Recommended
Land Pattern
0.050
1,27
Ambient temperature (°C)
0.230
5,84
Dimensions are in
inches
mm
Specifications subject to change without notice.
Please check our website for latest information.
© Coilcraft, Inc. 2009
Document 286-2
Revised 10/15/08
Similar pages